Search Results

Search found 22716 results on 909 pages for 'network architecture'.

Page 490/909 | < Previous Page | 486 487 488 489 490 491 492 493 494 495 496 497  | Next Page >

• Wifi antenna extension with F-connector/RG-6(RG-59) cable?

  - by rjz2000

  In an older house, the wire mesh in walls surrounding the furnace behave like a Faraday cage and block wifi signals. It is also difficult to lay new cable, however there is television cable to multiple locations due to there once having been a roof-installed, television antenna. It would be relatively trivial to install the wifi router at the center distribution point, then have the antenna broadcasting/receiving the signal plugged in at each of the old television outlets. I assume that it would not be too difficult to find an adapter for SMA <- F-type connectors. The cable is actually RG-59 rather than RG-6, but I assume that it still has relatively good RF isolation along its length, which is no more than a couple hundred feet in any direction. Does anyone know a problem with the idea? Will a router get confused if there is /too little/ interference between the two antenna? Is that length of cable (~100ft) too long for the signal a router broadcasts? I have seen that it is also possible to use old ~$30/each FiOS cable modems available on eBay to extend a network over television cable. However, that seems like a less elegant solution, and might interfere with upnp and dlna services I'd like to have work on a single network. Thanks if anyone has answers or suggestions before I try this project!

  Read the article

• Wifi antenna extension with F-connector/RG-6(RG-59) cable?

  - by rjz2000

  In an older house, the wire mesh in walls surrounding the furnace behave like a Faraday cage and block wifi signals. It is also difficult to lay new cable, however there is television cable to multiple locations due to there once having been a roof-installed, television antenna. It would be relatively trivial to install the wifi router at the center distribution point, then have the antenna broadcasting/receiving the signal plugged in at each of the old television outlets. I assume that it would not be too difficult to find an adapter for SMA <- F-type connectors. The cable is actually RG-59 rather than RG-6, but I assume that it still has relatively good RF isolation along its length, which is no more than a couple hundred feet in any direction. Does anyone know a problem with the idea? Will a router get confused if there is /too little/ interference between the two antenna? Is that length of cable (~100ft) too long for the signal a router broadcasts? I have seen that it is also possible to use old ~$30/each FiOS cable modems available on eBay to extend a network over television cable. However, that seems like a less elegant solution, and might interfere with upnp and dlna services I'd like to have work on a single network. Thanks if anyone has answers or suggestions before I try this project!

  Read the article

• which is best smart automatic file replication solution for cloud storage based systems.

  - by TORr0t

  I am looking for a solution for a project i am working on. We are developing a websystem where people can upload their files and other people can download it. (similar to rapidshare.com model) Problem is, some files can be demanded much more than other files. The scenerio is like: I have uploaded my birthday video and shared it with all of my friend, I have uploaded it to myproject.com and it was stored in one of the cluster which has 100mbit connection. Problem is, once all of my friends want to download the file, they cant download it since the bottleneck here is 100mbit which is 15MB per second, but i got 1000 friends and they can only download 15KB per second. I am not taking into account that the hdd is serving same files. My network infrastrucre is as follows: 1 gbit server(client) and connected to 4 Nodes of storage servers that have 100mbit connection. 1gbit server can handle the 1000 users traffic if one of storage node can stream more than 15MB per second to my 1gbit (client) server and visitor will stream directly from client server instead of storage nodes. I can do it by replicating the file into 2 nodes. But i dont want to replicate all files uploadded to my network since it is costing much more. So i need a cloud based system, which will push the files into replicated nodes automatically when demanded to those files are high, and when the demand is low, they will delete from other nodes and it will stay in only 1 node. I have looked to gluster and asked in their irc channel that, gluster cant do such a thing. It is only able to replicate all the files or none of the files. But i need it the cluster software to do it automatically. Any solutions ? (instead of recommending me amazon s3) S

  Read the article

• How can the route between two private IPs go via public IPs?

  - by Gilles

  I'm trying to understand what this output from traceroute means. I changed the IP addresses for privacy but retained the public/private IP range distinction. traceroute.db -e -n 10.1.1.9 traceroute to (10.1.1.9), 30 hops max, 60 byte packets 1 10.0.0.1 0.596 ms 0.588 ms 0.577 ms 2 10.0.0.2 1.032 ms 1.029 ms 1.084 ms 3 10.0.0.3 3.360 ms 3.355 ms 3.338 ms 4 23.0.0.4 3.974 ms 4.592 ms 4.584 ms 5 23.0.0.5 13.442 ms 13.445 ms 13.434 ms 6 45.0.0.6 13.195 ms 12.924 ms 12.913 ms 7 67.0.0.7 52.088 ms 51.683 ms 52.040 ms 8 10.1.1.8 46.878 ms 44.575 ms 44.815 ms 9 10.1.1.9 45.932 ms 45.603 ms 45.593 ms The first 10.0.* range is inside my organisation. The last 10.1.* range is another site of my organisation. The intermediate addresses belong to various ISPs. I expect that there is some kind of VPN between the two sites, but I don't know much about our network topology. What I don't understand is how the route can go from a private address through public addresses back into private addresses. Searching led me to Public IPs on MPLS Traceroute, which gives a possible explanation: MPLS. Is MPLS the only possible or most likely explanation? Otherwise what does this tell me about our network infrastructure? Bonus question for my edification: in this scenario, who is generating the ICMP TTL exceeded packets and if relevant mangling their source and destination addresses?

  Read the article

• virtualized windows 2003 domain with CentOS 5.3 and poor connectivity

  - by Chris Gow

  Hi: I have a test lab set up running a virtualized windows 2003 domain on a CentOS 5.3(xen) host and am experiencing connectivity problems with guests running on other hosts that are part of the same domain. Here's the setup: On Computer A I have CentOS 5.3 running as the host and have virtualized windows 2003 servers for a primary domain controller, a backup domain controller and an exchange server. The primary domain controller also acts as a WINS and dns server. The windows domain appears on a separate subnet from my company's corporate network. Connectivity to any of the virtualized guests on Computer A is fine (remote desktop, ping, what have you). I have another host computer (Computer B) that also has a virtualized Windows 2003 server guest that is part of the same domain. However, connectivity to that guest is flaky at best. I continuously get at least 60% packet loss when I try to ping the guest, and due to that flakiness I can not access any of the services that it runs (remote desktop, web). Now here's the interesting part. It seems to affect only machines running on a different computer than the domain controller that are in the same domain. On Computer B there is another Windows 2003 guest that is not part of the test domain and is on my corporate network. There's no connectivity issues with that guest machine. The problem does not seem to be specific to Computer B either. I created a test VM on my local computer within the test domain and it exhibits the same behaviour as the guest in Computer B. A couple of items to note: - Host OS on both Computer A and B are the same CentOS 5.3 64 bit - Guest OS is Windows 2003 64 bit and 32 bit (the guest on Computer B is 32 bit) - Guest OSes are all up to date (as of Monday) - Host OS on Computer A was upgraded from CentOS 5.2 to 5.3 Update: Sorry I did not follow up with the comments from below. Computer A and B have been moved to their own dedicated switch and the problem has gone away. I'm not sure what the underlying problem(s) were though

  Read the article

• Wifi Works with Android and Windows 8 but not Linux and Win 7

  - by eramm

  Support has told me that our company wide wifi network is setup to support mobile phones only. However it doesn't make sense to me that they can identify a mobile device rather they have setup the Access Point to use a protocol that is only supported on Android and Windows phones. Because the Access Point supports Windows mobile this means that laptops running Windows 8 can also connect to the Access Point (proven). So it stands to reason that since Android is based on Linux there must be a way to connect using Linux as well. iwlist shows IEEE 802.11i/WPA2 Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : TKIP CCMP Authentication Suites (1) : 802.1x WIreshark seems to show that a connection is being made to a website to get a certificate and use a Domain Controller for authentication. Questions: 1) what protocol could they be using that is supported on Win Mobile and Android but not on Win 7 and Linux (Debian) ? 2) what tools can I use to help me discover what protocol i need to support ? I have used iwlist and wireshark but I was not able to glean to much useful information from them. I can post the results if needed. 3) is there an app i can use on my Android phone to help me understand what kind of network it is connecting to ? I can provide more information if you tell me how to get it. I just don't know what I am looking for.

  Read the article

• Windows Server 2012 Can't Print

  - by Chris

  I know this may sound incredibly stupid and there is probably an easy solution but I can't seem to find it. Friends of mine recently upgraded their server for their small business from the POS old one. New hardware and a change from Windows Server 2003 to Windows Server 2012. I've got everything they need transfered over and running except for printing. They need to be able to print to printers in the vans their technicians use from the server via remote desktop. In other words the use a laptop to remote desktop into the server and need to print invoices out from the remote server to printers attached locally via usb. On the old server they just installed the identical driver and that was it, they could print as needed. On this server no matter what we seem to do we can't get it to print remotely, and in the process we also discovered that the server can't even print to the network printer. It sees the printer on it's network and it sees (through redirect) the printers in the vans but when you hit print it claims it did and nothing happens. There isn't an issue with the printers themselves as every other device we have can print to them without issues. Is there some setting that is inhibiting the server from printing? Is there something I need to install (print server?) to add the functionality? Thanks in advance for helping me out here

  Read the article

• Linux: CIFS/Samba mount hangs for several minutes

  - by Pistos

  I have a small local network which has a Gentoo box and a Windows box. I mount a share originating on the Windows box onto the Gentoo box with a command like: mount -t cifs -o username=WindowsUsername,password=thepassword,uid=pistos //192.168.0.103/Users /mnt/windowsbox Most of the time, everything Just Works, and I can read and write without problems. However, every few weeks or so, the connection or the mount point seems to go dead or hang, such that any process that tries to access the mount point gets stuck in D state (disk, or I/O wait). These processes become impervious to TERM and KILL signals. Disconnecting and reconnecting the Windows box from the network does not help. The frozen state lasts for 5+ minutes. It's really frustrating and gets in the way of normal work, because it freezes Save As dialogues, ls commands, etc. If I issue a umount on the mount point, it either hangs also, or reports that the mount point is in use. Eventually, the dead state resolves itself, and the mount point gets unmounted, or it becomes possible to umount with no delay. My guess is that this happens when the connection/mount has gone idle, or when the Windows machine has been idle. I am not really sure. Why is this happening, and what can I do to prevent it? Or how can I successfully kill these D-state processes at will? Possibly related: CIFS mounts hang on read

  Read the article

• Cannot Connect To VMWare Guest OS Using NEither RDP Nor

  - by Humanier

  Hi, I have a PC (Windows XP SP3) with VMWare Workstation 7 installed. The VMWare hosts Windows Server 2003 Enterprise Edition R2. RealVNC (4.1.3) is installed on both OS'es. Both of them use Hamachi2. Host OS (WinXP) also runs ZoneAlarm Firewall. Hamachi network is set as trusted. My goal is to allow RDP and VNC connections to be made to the guest OS (Windows Server 2003). Both options work absolutely fine if I connect from the host OS. However I have problems when other computers from our Hamachi network try to connect the guest OS (Win2K3). 1) RDP connections. RDP window opens, shows black content and after 15-20 seconds displays following error: http://lh6.ggpht.com/_yQhsRRimgKU/TArRrtiteQI/AAAAAAAABZA/e96za-y9wzo/rdp_error.JPG 2) RealVCN connections. Users are able to connect but all they see is a black screen inside VNC window. At the same their input (keystrokes or mouse moves/clicks) are visible when looking at the console window of the Win2K3. I really appreciate any ideas on how to resolve mentioned problems. Thank you in advance.

  Read the article

• Access server using IP on another interface

  - by Markos

  I am using Windows Server 2012 instead of a router for my home network. Currently I am using RRAS and computers from local network can access Internet correctly. Here is a map of the current setup: [PC1] ---| |---- (lan ip)[Server](wan ip)--> internet [PC2] ---| I have applications running on Server, such as IIS and others. All can be accessed from internet using wan ip and from lan using lan ip. I have a domain, lets say its my-domain.com, which is resolved to my wan ip. What I want is to enable my LAN computers to be able to connect to services on my server using the very same address as internet users: eg http://my-domain.com/. However this does not work for my lan computers. What I understand is that I need to set up some kind of loopback route in a way that packets comming to LAN interface get routed to WAN interface. But I haven't found how to achieve this (in fact, I don't know WHAT to search for). Feel free to ask for additional informations and I will try to update the question.

  Read the article

• Pinging computer name in LAN results in public IP?

  - by Bob

  Hi, I recently introduced a new machine to my LAN. The computer name for this machine is 'server'. Historically I've been able to access machines from my home network (from a web browser or RDP) using the machine name and it resolves to a local IP address just fine. However, I can't seem to do this anymore. When I ping the computer name, I get the following: C:\Users\Robert>ping server Pinging server.router [67.215.65.132] with 32 bytes of data: Reply from 67.215.65.132: bytes=32 time=24ms TTL=54 Reply from 67.215.65.132: bytes=32 time=23ms TTL=54 Reply from 67.215.65.132: bytes=32 time=24ms TTL=54 Reply from 67.215.65.132: bytes=32 time=24ms TTL=54 I notice also that it appends the 'router' suffix to my domain name for some reason. 'router' is the name of my router, obviously. I'm also using OpenDNS as my DNS provider (configured through my router so it gets passed down through DHCP). Why is this not working for me? Can someone explain how the DNS resolution should take place? For LAN resolution, it shouldn't go straight to OpenDNS. I thought that each Windows machine kept it's own sort of "mini DNS server" that knows about all machines on the local network and it first tries to resolve using that. Please let me know what I can do to get this working!

  Read the article

• "Ethernet" doesn't have a valid IP configuration

  - by Xuzuno

  I'm using an ethernet cord to connect to my internet and it has been working well until Thursday morning when I turned on my laptop (Windows 8) to see a yellow triangle sign in the bottom right hand corner, in front of the ethernet connected symbol. Since then I haven't been able been able to access the internet from my computer. When I hover over it, it says that it is an "Unidentified network" and there is "No internet access". I've run the Windows 8 troubleshooting and it says that the problem found was ""Ethernet" doesn't have a valid IP configuration", but I'm unsure how to fix it. I'm thinking that the problem is to do with my computer rather than my network, because I've tried another laptop (Windows 7) through the same ethernet cable and connection and the internet works fine on the other laptop. I've tried so many fixes that I've found online, with none of them actually working. Yesterday I even tried a full system reset, where I re-installed Windows 8, re-partitioned and wiped everything off the hard drive, but it still appears have the exact same problem. Today I also purchased and tried a new ethernet cable which didn't work, so I then purchased a USB to Ethernet adapter, to make sure that it wasn't my ethernet port on my laptop that was faulty. That didn't work either, and the same problem still remains. I feel like I've tried everything, so can someone please help me?

  Read the article

• openVPN as a way to connect to a LAN by another client, different from server

  - by Einar

  Setup: one LAN handled by a router without a publicly available IP address but without any outbound connection restrictions ("target LAN"); a separate server publicly reachable from the Internet ("gateway"). I am trying to set up openVPN so that a third client can connect to the "gateway" and access the "target LAN". As the router of "target LAN" is not reachable from the Internet directly, it connects to the gateway itself via openVPN as well. The problem is how to handle routing. The LAN router has two network interfaces (for the outside network and the LAN itself). In openVPN (the server on the gateway) I set client-to-client and push "route 192.168.10.0 255.255.255.0" but I assume this would be horribly wrong (it actually messed up the routing on the LAN router until I killed openVPN). openVPN is not using bridging, is configured via tun. Other config details from the server server 10.8.0.0 255.255.255.0 client-config-dir ccd route 192.168.10.0 255.255.255.0 And the client file in ccd is iroute 192.168.10.0 255.255.255.0 What can be adjusted to ensure that a third client can connect through openVPN and access the LAN mentioned earlier?

  Read the article

• Measure Upload Speed between a client and our server

  - by tresstylez

  We host a SAAS application specially customized for multiple clients. For one customer in particular -- they are reporting sporadic performance issues from various locations on their network, in particular UPLOADING documents through a form on our website. The client claims they have "bandwidth to spare" and that utilization of their "pipe" is so low that it MUST be our application, but our application has MANY clients and all features are working fine for all other clients. Interestingly enough -- DOWNLOADS (ie. just accessing the website, or downloading documents) is working fine. Speed test shows that they should get 1.2Mbps UP. So, a 3MB file should take 20 secs to upload. It takes 60+ seconds on their network. Sometimes even small files take OVER 10 minutes to upload or they timeout. Pings and Traceroutes don't show any abnormally long hops or response times. They claim other SAAS applications they use allow them to upload just fine. Both IT teams are working together to resolve this issue. What kind of data can I request from the clients to begin ruling things out. Seems like we need to somehow measure LATENCY of the networks involved or even at the switch level, we need to understand if packets are getting dropped somewhere and why. Where should I start? Any help is appreciated. I'll provide more info upon requests

  Read the article

• Find routers IP address on the other side

  - by corsiKa

  Here's the basic setup of my network In this diagram: 1: The internet c: cable 2: Wireless router w: wireless connection 3: A win7 box with internet connection sharing enabled 4: A wireless router, but I'm only using its LAN capabilities to connect box 5 to the internet. 5: A win7 box, the computer I'm using to make this post. So its internet works just fine. Now if I'm on box 5, and I ping 192.168.1.1, I hit 4. If I'm on box 3 and I ping 192.168.1.1, I hit 2. Now obviously box 3 does not think 4's IP address is 192.168.1.1, or I wouldn't be able to connect to the internet. Okay, now that you know as much as I do about my network, here's my question: If I was on box 3, how would I determine the IP address of 4? Basically I'm running a webserver on box 5 and want to access this webserver on box 3 and other boxes. So that's the end goal. If there's other information there that can help, I'd appreciate it. Thanks!

  Read the article

• Print from Linux to Windows networked printer

  - by wonkothenoob

  I want to print from a Debian (Lenny) workstation to a Windows networked printer. I'm not even sure what type of Windows network this is. Our tech-support is friendly but doesn't want to get involved with supporting Linux. I need to use it for a variety of reasons and am completely stumped because I know nothing about Windows networking. They gave me URI smb://msprint.ourorg.edu as the "address" of the printer and further confirmed that the domain is "OURORG" and the share is "PHYS-PRI". I've installed CUPS and made sure that it's running as a daemon, I've clicked on the system-config-printer[1] icon, selected the printer as a Windows printer shared via SAMBA and entered the above URI. Attempting to print a testpage just sees it sit in the queue. I attempted to see if I could access the share using two other methods. Method 1. First I tried the "smbclient" from the CLI: $ smbclient -L //msprint.ourorg.edu -U user23 timeout connecting to 192.168.44.3:445 timeout connecting to 192.168.44.3:139 Connection to msprint.ourorg.edu failed (Error NT_STATUS_ACCESS_DENIED) Method 2. I tried to use the GUI tool Smb4K. This shows me four other toplevel (I'm assuming they're domains?) groupings one of which is the one which our IT department supplied to me. Clicking them shows a bunch of other machines with (what I assume are NetBIOS names?) including my own. I see all sorts of other networked printers belonging to other departments but none within mine. Certainly not the PHYS-PRI one suggested to me by the IT folks. I realize that I'm probably using the wrong terminology for the windows network, but can anyone help me with this? What steps should I be taking in debugging this? Do I need to actually run my machine as a SAMBA server to authenticate to the printer or should I just be able to communicate using CUPS? It's a GUI to CUPS configuration http://cyberelk.net/tim/software/system-config-printer/

  Read the article

• Using Windows Explorer, how to find file names starting with a dot (period), in 7 or Vista?

  - by Chris W. Rea

  I've got a MacBook laptop in the house, and when Mac OS X copies files over the network, it often brings along hidden "dot-files" with it. For instance, if I copy "SomeUtility.zip", there will also be copied a hidden ".SomeUtility.zip" file. I consider these OS X dot-files as useless turds of data as far as the rest of my network is concerned, and don't want to leave them on my Windows file server. Let's assume these dot-files will continue to happen. i.e. Think of the issue of getting OS X to stop creating those files, in the first place, to be another question altogether. Rather: How can I use Windows Explorer to find files that begin with a dot / period? I'd like to periodically search my file server and blow them away. I tried searching for files matching ".*" but that yielded – and not unexpectedly – all files and folders. Is there a way to enter more specific search criteria when searching in Windows Explorer? I'm referring to the search box that appears in the upper-right corner of an Explorer window. Please tell me there is a way to escape my query to do what I want? (Failing that, I know I can map a drive letter and drop into a cygwin prompt and use the UNIX 'find' command, but I'd prefer a shiny easy way.)

  Read the article

• Can not open ports in iptables on CentOS 5??

  - by abszero

  I am trying to open up ports in CentOS's firewall and am having a terrible go at it. I have followed the "HowTo" here: http://wiki.centos.org/HowTos/Network/IPTables as well as a few other places on the Net but I still can't get the bloody thing to work. Basically I wanted to get two things working: VNC and Apache over the internal network. The problem is that the firewall is blocking all attempts to connect to these services. Now if I issue service iptables stop and then try to access the server via VNC or hit the webserver everything works as expected. However the moment I turn iptables back on all of my access is blocked. Below is a truncated version of my iptables file as it appears in vi -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 5801 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 5901 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 6001 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 5900 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 80 -j ACCEPT Really I would just be happy if I could get port 80 opened up for Apache since I can do most stuff via putty but if I could figure out VNC as well that would be cool. As far as VNC goes there is just a single/user desktop that I am trying to connect to via: [ipaddress]:1 Any help would be greatly appreciated!

  Read the article

• What is going on when I can't access an SMB server share (not accessible error) until I run cmdkey to delete the credential?

  - by Warren P

  I have a network connection share issue. The first connection works, and seems to stay connected for at least a few hours. However, after each time my windows 7 PC reboots, it can no longer form a network connection to the shared folder, nor browse to it, until I not only unmap and remap the mapped drive, but also, I have to use cmdkey to delete the stored credentials like this: cmdkey /delete:Domain:target=HOSTNAME My work PC is on a domain, and I am not the IT administrator, but I'm curious if there is anything I can do to investigate this issue. Any settings in registry or group policy that I could examine to see why the first connection works, but each subsequent attempt (once a stored credential exists) to browse or use the connection, fails with a connection error saying it is "not accessible", like this: I do not even get any error until at least several minutes go by. THe first thing I see is a window frozen and empty, and then I get this error: This has happened when connecting to a share on a DROBO device, and on a share which is not on the domain, but which was a Microsoft Home Server. I wonder if there's something broken in WIndows 7 professional with regards to connecting to non-domain shares when an active directory domain controller exists, and a particular workstation is joined to a domain? The problem only occurs if I click "remember credentials". It is not fixed by any amount of working with net use. Usingcmdkey to delete all stored credentials for the host is the only way to get back in, and it affects all non-domain shared folders. Update I'm hoping there are some registry locations I could check that could be misconfigured in some way that might explain why SMB/CIFS stored credentials for non-domain systems seem to be auto-invalidated in this weird way. Knowing how whacko Microsoft Windows domain and security handling is sometimes, this could be some kind of stupid "feature".

  Read the article

• Routing and authenticating all access through squid

  - by Knight Samar

  Hi, I want to route all Internet access in my network through a Squid proxy server and authenticate and log all users. I want this to be a client-independent setting so that no one needs to do anything on their browsers or machines. I have set my network gateway as the proxy server so that all traffic will be sent to it. I have done this using options in DHCP server. Now I tried using squid as a transparent proxy, but then it won't authenticate in that mode. I tried using iptables to route all traffic to port 3128 but it won't popup the authentication dialog box from SQUID. I tried telling DHCP to give WPAD to all clients by placing a WPAD file on a webserver containing the following for automatic proxy configuration on clients: Changes in dhcpd.conf option wpad code 252 =test; option wpad "\n\000"; option wpad "http://192.168.1.5/wpad.dat\n"; The WPAD file: function FindProxyForURL(url,host) { return "PROXY squid-server-ip-address:3128 ; DIRECT "; } But the browsers (different versions of Firefox and IE) seem to ignore it. :( What should I do ?

  Read the article

• TCP Keepalive and firewall killing idle sessions

  - by Carlos A. Ibarra

  In a customer site, the network team added a firewall between the client and the server. This is causing idle connections to get disconnected after about 40 minutes of idle time. The network people say that the firewall doesn't have any idle connection timeout, but the fact is that the idle connections get broken. In order to get around this, we first configured the server (a Linux machine) with TCP keepalives turned on with tcp_keepalive_time=300, tcp_keepalive_intvl=300, and tcp_keepalive_probes=30000. This works, and the connections stay viable for days or more. However, we would also like the server to detect dead clients and kill the connection, so we changed the settings to time=300,intvl=180,probes=10, thinking that if the client was indeed alive, the server would probe every 300s (5 minutes) and the client would respond with an ACK and that would keep the firewall from seeing this as an idle connection and killing it. If the client was dead, after 10 probes, the server would abort the connection. To our surprise, the idle but alive connections get killed after about 40 minutes as before. Wireshark running on the client side shows no keepalives at all between the server and client, even when keepalives are enabled on the server. What could be happening here? If the keepalive settings on the server are time=300,intvl=180,probes=10, I would expect that if the client is alive but idle, the server would send keepalive probes every 300 seconds and leave the connection alone, and if the client is dead, it would send one after 300 seconds, then 9 more probes every 180 seconds before killing the connection. Am I right? One possibility is that the firewall is somehow intercepting the keepalive probes from the server and failing to pass them on to the client, and the fact that it got a probe makes it think that the connection is active. Is this common behavior for a firewall? We don't know what kind of firewall is involved. The server is a Teradata node and the connection is from a Teradata client utility to the database server, port 1025 on the server side, but we have seen the same problem with an SSH connection so we think it affects all TCP connections.

  Read the article

• Ubuntu Server Wireless connection issue - replaced router but kept ESSID

  - by Stevo

  I have a ubuntu server 12.04 which was connected to my wireless network with no problem I replaced the wireless router but kept the ESSID and password the same. All other devices on network have connected correctly. However the Ubuntu Server will not route correctly. It will connect to the wifi router, and get a dhcp served IP address, however it will not route anything. I cannot ping the router from the server. the contents of /etc/resolve.conf are updated with the information from the router, (the host name has been served) I know there is nothing wrong with the router or the server, or the wireless card etc. I'm assuming there's some cached setting that associates the old router with the ESSID and causing the issue. I've got a lot of other devices connected to the router, so don't want to change the name of the ESSID. How do I fix this? EDIT: outputs (abbreviated as I've got no cut and paste) netstat -rn: Kernel IP Routing table Dest Gate Gen Flags MSS Window irtt Iface 0.0.0.0 192.168.0.1 0.0.0.0. UG 0 0 0 wlan0 192.168.0.0 0.0.0.0. 255.255.255.0 U 0 0 0 wlan0

  Read the article

• Reverse proxy for mailserver (SMTP + HTTP for web client)

  - by ba

  I'm looking at doing some reverse proxy work for a mail server with corresponding web client. Both servers are running on the same machine, this is not a server with a high load. :) The solution I've discussed with friends is having the mail server/web client on our internal network. Then to put a reverse proxy on the DMZ to service both SMTP and web client HTTP-traffic to the mail server on the internal network. From what I understand this is the recommended secure solution? So far I've thought for the SMTP-proxy part of using postfix which will receive mail, do some spamhause and similar anti-spam measures and if it all checks out, send the mail to the mail server on the inside. The mail server on the inside will send all outgoing mail to the proxy which will then send it out on the Internet. For the web client I'm not sure exactly which software I should be running on the proxy machine, I've been thinking about using Squid -- but that's basically based on the fact that I know squid is a http proxy. The web client data will be sent out over SSL. Reading around some here on Serverfault I've seen other people using Apache with mod_proxy+mod_security for similar situations. Am I thinking correctly for this solution? What software would you guys use and with which modules? Thanks in advance for the help! :)

  Read the article

• Slow tracepath on local LAN

  - by Simone Falcini

  I am on EXSi and I have 2 instances: Ubuntu and CentOS. These are the network configurations Ubuntu eth0 Link encap:Ethernet HWaddr 00:50:56:00:1f:68 inet addr:212.83.153.71 Bcast:212.83.153.71 Mask:255.255.255.255 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:76059 errors:0 dropped:26 overruns:0 frame:0 TX packets:7224 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:6482760 (6.4 MB) TX bytes:2080684 (2.0 MB) eth1 Link encap:Ethernet HWaddr 00:0c:29:46:5a:f2 inet addr:192.168.1.1 Bcast:192.168.1.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:252 errors:0 dropped:0 overruns:0 frame:0 TX packets:608 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:42460 (42.4 KB) TX bytes:82474 (82.4 KB) /etc/iptables.conf *nat :PREROUTING ACCEPT [142:12571] :INPUT ACCEPT [5:1076] :OUTPUT ACCEPT [8:496] :POSTROUTING ACCEPT [8:496] -A POSTROUTING -s 192.168.1.0/24 -o eth0 -j MASQUERADE COMMIT *filter :INPUT ACCEPT [2:72] :FORWARD ACCEPT [4:336] :OUTPUT ACCEPT [6:328] -A INPUT -i eth1 -p tcp -j ACCEPT -A INPUT -i eth1 -p udp -j ACCEPT -A INPUT -i eth0 -p tcp --dport ssh -j ACCEPT COMMIT CentOS eth0 Link encap:Ethernet HWaddr 00:0C:29:74:1C:55 inet addr:192.168.1.2 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::20c:29ff:fe74:1c55/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:499 errors:0 dropped:0 overruns:0 frame:0 TX packets:475 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:68326 (66.7 KiB) TX bytes:82641 (80.7 KiB) The main problem is that if i execute this command from the CentOS instance ssh 192.168.1.2 it takes more than 20s to connect. It seems like it's routing the connection to the wrong network. What could it be? Thanks!

  Read the article

• Changing SkyDrive default location on Windows 8.1

  - by jmblack

  Update: This issue is due to the use of any non-local location for the SkyDrive folder. I've currently worked around this by using a local folder, but this has not resolved the original problem. I am trying to change the location where SkyDrive is located in Windows 8.1. This is the newly integrated SkyDrive, and not a downloadable client. There are a couple of similar questions on this site, but they pertain to Windows 8 and 8.1 Preview: Changing the SkyDrive default path in Windows 8.1 (Windows 8.1 Preview) How do I change the SkyDrive default folder in Windows (Windows 8) The SkyDrive folder is a system folder in 8.1, and like other system folders, has a Location tab in its properties that theoretically lets you change its location. I was able to do this with other system folders such as Downloads and Pictures, but there is an error when I try to change this for SkyDrive. Edit: The location that causes this error is a mapped network drive. The error does not occur when trying to move SkyDrive to another location on the same drive. There are no permission restrictions on the mapped network drive. Edit #2: This is the method I followed that produced the error: A screenshot of the error can be found here Has anyone else encountered this or have any information on this?

  Read the article

< Previous Page | 486 487 488 489 490 491 492 493 494 495 496 497  | Next Page >