Search Results

Search found 13575 results on 543 pages for 'desktop virtualization'.

Page 493/543 | < Previous Page | 489 490 491 492 493 494 495 496 497 498 499 500  | Next Page >

• Why can't a PC with 2 network cards be accessed by hostname?

  - by lewis

  I set up PC with 2 network cards, connected to the same LAN. I can connect to this PC (e.g. by remote desktop) only via ip-addresses. Accessing by hostname does not work. Why is this the case? UPDATE: Full environment 1. PC with 2 hardware network adapters. 2. On this PC installed VMWare Workstation. Created 3 VM's, networked by "bridged" network setting in VMWare. 3. In LAN all ip-addresses given from DHCP. 4. Win2k8 on all hosts (both physical and vitrual). As result: 1. PC has 2 ip-address (e.g. 192.168.1.71 and 192.168.1.72). PC available in LAN by ip-addreses, but not avail by hostname. 2. VM's has own ip-addr on each (e.g. 192.168.1.73, *74, *75 etc). They are available from LAN by their ip's, BUT not by their hostnames. How can I access to PC and to VM's by hostname?

  Read the article

• Is it a good Idea to switch to a SSD to use less battery?

  - by Walter Maier-Murdnelch

  I am thinking of buying a SSD for my laptop, mainly for the purpose of extended operating time when running on battery. At the moment I use a Hitachi HTS545032B9A300 (320GB) (Datasheet) as main drive and a Seagate Momentus 5400.3 120GB as secondary drive. I dualboot Windows and Linux but I don't need the windows partition any longer, a 120GB SDD would be more than sufficient space-wise. Speed is not an issue for me, I make heavy use of tmpfs (ramdrive) within Linux and transfers of bigger files are mainly through some network filesystem anyways, thus a cheaper SSD should do. For the purpose of comparison I chose the OCZ Vertex Plus 120GB. Power consumption always is a big promotional thing the industry uses to make me want to buy their SSDs, some sheet on the OCZ page provides an astonishing comparison of desktop HDDS and SSDs. The numbers I got comparing my laptop HDD and their SSD were not really astonishing any longer. Hitachi 320GB HDD: Startup (W, peak, max.) 4.5 Seek (W, avg.) 1.7 Read / Write (W, avg.) 1.4 Performance idle (W, avg.) 1.3 Active idle (W, avg.) 0.8 Low power idle (W, avg.) 0.5 Standby (W, avg.) 0.2 Sleep 0.1 OCZ 120GB SSD: 1.5W active 0.3W standby I see that there are differences, but actually they don't seem that high as I though they were. And compared to the power consuption of the rest of my system I wonder if it makes a difference at all. Have I just taken the wrong look at the whole thing or may I be better off to buy another battery for my laptop?

  Read the article

• RHEL 5.3 Kickstart - How specify location of individual package in Workstation folder?

  - by Ed

  I keep getting "package does not exist" errors during the install. I made a kickstart ISO to create an unattended install of a RHEL 5.3 build machine for C++ software releases. It pulls the kickstart config file from our internal web server. This is handy; it makes it easy to test and modify without having to make a new ISO. And I plan to check it in to version control if I can get it working. Anyway, the rpm packages are located in two folders on the disk; Client and Workstation. The packages install fine for the ones that are physically located under the Client folder. It cannot find those under the Workstation folder such as as doxygen and subversion complaining that packages do not exist. Is there a way to specify the individual package location? # ----------------------------------------------------------------------------- # P A C K A G E S # ----------------------------------------------------------------------------- %packages @gnome-desktop @core @base @base-x @printing @development-tools emacs kexec-tools fipscheck xorg-x11-server-Xnest xorg-x11-server-Xvfb #Packages Located in Workstation Folder *** Install can not find any of these ?? bison doxygen gcc-c++ subversion zlib-devel freetype-devel libxml2-devel Thanks in advance, -Ed

  Read the article

• Ubuntu 12.04 Very slow especially with Android Studio

  - by Nada

  I have an old laptop with the following specification: Memory: 485 MiB, Processor: Genuine intel CPU T2300 @ 1.66 GHz ×2, OS Type: 32 bit, Disk: 78.1 GB, I installed on it Ubuntu 12.04 LTS and I noticed that the overall system is very slow in responding. I tried to search about that in the internet and I found some articles talking about how to make Ubuntu 12.04 LTS run fast I applied all what they said including download LXDE desktop environment and then nothing different in the system response time. Then I need to develop some android applications so, I download Android Studio (Beta) 0.8.6. The problem became worse than before whenever I tried to open the Android Studio the screen is frozen for some minutes then it took time to download the projects and initialize the work space also, when I tried to move the cursor he is move very slowly. When I tried to run my first application on the AVD it took three hours and still not run yet. I delete the Android Studio and install it again several times, I was trying to solve the problem but still nothing change. Please if you have any suggestions that may help me make my laptop and Android Studio work faster I will appreciate it for you. Thank you in advance.

  Read the article

• Sharing music on NAS with Zune and iPod?

  - by osij2is

  After being a long time iPod owner, I'm switching to the new Zune with its subscription model. I haven't bought a Zune yet but I'm planning on doing so within the next month or so. I have approximately 40GB worth of music and my girlfriend has her iPod music library around 30GB. I've been trying to figure out how to migrate all our music off of our laptops/desktops and centralize everything on my NAS. In sharing iPod music isn't too bad. Sharing from one machine to all is fairly easy within the iTunes player. As far as storing all the music on a NAS, again, iPods aren't too bad and imagine other systems aren't difficult. But I'm really new to the Zune and I'm beginning to run into some issues. My questions are: Is it possible to store all music from our iPods and Zune subscriptions and share music between the iPod/Zune within the same file share on my NAS? I'm sure it's possible to store music on a share, but I'm not sure how iTunes and the Zune software differs. Is there 3rd party software, maybe something like DoubleTwist that can sync based from NAS to multiple desktop/laptops? I've never used DoubleTwist but it's something that I found that looks close to being what I need. I've never quite done this myself so I'm trying to find a solution that can: a) store music on a network share; b) sync between different devices (Zune/iPod) seamlessly.

  Read the article

• Half of installed RAM is hardware reserved

  - by user968270

  After a rather arduous and convoluted series of problems that left me without a desktop for ~80 days, I've finally got the thing up and running, having replaced the power supply, motherboard, graphics card and CPU. Now, however, I'm experiencing the 'hardware reserved RAM' issue. Perhaps this is the exhaustion talking, but looking at the question that tends to get pointed to when this kind of topic gets locked as a duplicate hasn't helped. I have 16 GB of RAM installed in an MSi 970A-G46, which is spec'd for up to 32 GB of RAM. The BIOS recognizes that I have 16 GB installed, and the resource monitor also shows the whole 16 GB, only it shows 8 GB as hardware reserved. I've seen suggestions that it's an OS issue, but the particular installation of Windows 7 (64-bit) which I'm running on my boot drive is the same as the one that could actually access the 16 GB in my previous motherboard (MSi 870A-G54). I've updated my BIOS using the MSi Live Update tool and restarted the machine with no effect, and I cannot seem to locate any 'Memory Remapping' option as I've seen mentioned. I've physically swapped the RAM between the slots to no effect. I've unchecked the Maximum Memory box in the msconfig Boot tab's advanced options, also to no effect. These are my system's basic specifications OS: Windows 7 Home Premium (64-Bit) Motherboard: MSi 970A-G46 CPU: AMD FX-8150 Graphics Card: XFX Radeon HD 6870 Boot Drive: OCZ Agility 3 Storage Drive: Samsung Spinpoint F3 ST1000DM005/HD103SJ 1TB PSU: Thermaltake TR-2 TR600 600W ATX12V v2.3

  Read the article

• Computer keeps restarting [closed]

  - by Joris

  I have a strange problem with my desktop pc, when I start it, it just restarts immediately, it displays the bios/motherboard logo and then restarts. I can't access the bios to edit settings because it restarts to fast. Then I tried different things to fix it with mixed success. (I also tried to reset the bios without success) I noticed that a capacity from the graphics card was broken (it looked exploded) so I ordered a new graphics card & plugged it in the computer. It didn't change much, still the same problem. Then I unplugged everything that's not necessary and put only 1Gig RAM in the motherboard (usually it has 4 x 1Gig RAM) and the computer started, then I putted another gig of RAM and the computer still started. (starting=booting windows) When I putted in the 3th RAM it didn't boot anymore (again restarting all the time) so I removed this 3th gig of RAM and this is where it gets weird. I expected the computer to boot again because it is exactly the same configuration as before - which worked - but the computer didn't want to start. It just gave the same problem as before (restarting all the time.. ) Anyone an idea what might be wrong?

  Read the article

• What mobile phones are viable for a "nerdy" person? [closed]

  - by Blixt

  This community wiki is for determining a list of good mobile phone choices if you are "nerdy" (definition follows.) As a point of reference, the almost two years old N95 8GB will be used. Mostly because that's what I can most relate to since I've had it since it came out. Today, iPhone and other modern mobile phones really out-shine it in usability and interface. However, it still does everything I want it to do (and here's the definition of "nerdy"; modify as needed): Syncs contacts, calendar, tasks and mail in the background Can run multiple installable applications in the background (Google Maps with Latitude, for example) Good amount of space for music etc. Lets you develop your own little toy applications (Python; not to mention it can also run an Apache server with a public URL!) Tethering! Supports Flash (maybe not very important, but it has its uses) Has a manufacturer that believes in the nerdiness! (The people at Nokia Labs make lots of cool stuff and share early versions with the community and are generally open) A high resolution screen (at least 320x240) Special hardware features such as an accelerometer and GPS What's missing from the N95 8GB but still qualifies as good, "nerdy", qualities: 7.2 Mbit/s (or faster) internet through HSDPA or HSPA+. A good web browser that can do most of the stuff a desktop browser can (especially render sites properly and run JavaScript correctly) Touch (especially multi-touch) More special hardware features such as a compass Intuitive and fluent user interface (Shiny stuff) Ability to configure it to trust root certificates of my own choice A processor fast enough to run Quake 3! =)

  Read the article

• Recovering corrupted VB.NET Form file?

  - by Omega

  Good day. This question is directly related to this one I made here: http://stackoverflow.com/questions/4911099/there-is-no-editor-available-for-form1-vb-error There, I was working on my VB.NET 2010 Express application, I saved, then a blackout came and now, apparently, I can't view the designer nor code of my Form file (Form1.vb). On StackOverflow, I was recommended to check for the From1.vb file, and try to open it on Notepad. If nothing appeared, it would mean that my file was corrupted. I open it on Notepad, and I get a blank file. It is 27kb, but it only has blank spaces. So I assume it is corrupted. I was told this place was better for dealing with corrupted files, about techniques to recover them. I use Windows7, VB.NET 2010 Express. I run Windows7 on Parallels Desktop, Mac OS X. However, I do not believe that is the problem, most likely it was that damned blackout... this is the first time that happens to me. VB.NET worked just fine for me all time (about a month and half). Thank you.

  Read the article

• "Network is unreachable" When pinging google, can connect to internal computers on debian VM

  - by musher

  Similar to this SU question: "Network is unreachable" when attempting to ping google, but internal addresses work Actually, it's pretty much the same base issue. I went through that thread trying to find a solution, I changed my resolv.conf: before: domain [my work domain] search [my work domain] nameserver [my gateway] nameserver [my gateway2] I changed it to: after: domain [my work domain] search [my work domain] nameserver 8.8.8.8 nameserver 8.8.4.4 However, any time I reboot the computer the resolv.conf gets overwritten to the previous version (the 'before' above). The issues began after I installed virtualbox additions, X server and (specifically) LXDE: Cat of apt history.log: Start-Date: 2014-08-21 10:03:42 Commandline: apt-get install virtualbox-guest-utils virtualbox-guest-dkms Install: x11-xkb-utils:amd64 (7.7+1, automatic), libxaw7:amd64 (1.0.12-2, automatic), xfonts-utils:$ End-Date: 2014-08-21 10:03:56 Start-Date: 2014-08-21 10:18:39 Commandline: apt-get install lxde Install: desktop-base:amd64 (7.0.3, automatic), libgoa-1.0-0b:amd64 (3.12.4-1, automatic), lxmenu-d$ End-Date: 2014-08-21 10:21:52 Start-Date: 2014-08-21 10:26:40 Commandline: apt-get upgrade Upgrade: libio-socket-ssl-perl:am ifconfig on the guest: root@Peridot:~# ifconfig eth0 Link encap:Ethernet HWaddr 08:00:27:89:c9:20 og inet addr:172.31.2.102 Bcast:172.31.2.255 Mask:255.255.255.0 inet6 addr: fe80::a00:27ff:fe89:c920/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:2281 errors:0 dropped:1 overruns:0 frame:0 TX packets:463 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:266507 (260.2 KiB) TX bytes:120554 (117.7 KiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:4 errors:0 dropped:0 overruns:0 frame:0 TX packets:4 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:240 (240.0 B) TX bytes:240 (240.0 B) The adapter in VBox is a bridged adapter directly onto my ethernet connection; as are my other 2 VMs (which work) Other SU questions I've tried: "connect: Network is unreachable" in VirtualBox VM

  Read the article

• Print over remote CUPS server, but just show a subset of the printers.

  - by jdm

  I'd like to print from my Ubuntu laptop (karmic) to some networked printers. Our organisation uses a CUPS server with several hundred printers. What I know I can do is: CUPS_SERVER=printers.company.com acroread document.pdf and then Adobe Reader shows me all available printers to select from. However, it takes a couple of minutes to display the large list, which is really annoying. (The desktop PCs here suffer from this, too.) The other option is to add a new printer with an address like ipp://printers.company.com/printer/bldg1_hp8150 (to the Ubuntu printer configuration = local CUPS server). However, it asks me for a driver. I don't want to / can't always specify a driver, since some printers don't appear in the list. I'd like to let the remote CUPS server handle the driver part (like it does when i set CUPS_SERVER), and do no more preprocessing/"driver stuff" on my side. The ideal thing would be if I could somehow add the remote printer list to my local cups server, and apply a filter, so that it would just display printers a la bldg1_*. This feature was available in KDE3.?, but I can't find something similar in Ubuntu/Gnome. Any suggestions?

  Read the article

• Route web traffic through a separate iterface

  - by tkane

  I'd like to route web traffic through the wlan0 interface and the rest through eth1. Can you please help me with the iptables commands to achieve this. Below is my configuration. Thank you :) Edit: This is about desktop configuration not a web server set up. Basically I want to use one of my connections to browse the web and the other one for everything else. ifconfig: eth1 Link encap:Ethernet HWaddr 00:1d:09:59:80:70 inet addr:192.168.2.164 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::21d:9ff:fe59:8070/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:33 errors:0 dropped:0 overruns:0 frame:0 TX packets:41 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4771 (4.7 KB) TX bytes:7081 (7.0 KB) Interrupt:17 wlan0 Link encap:Ethernet HWaddr 00:1c:bf:90:8a:6d inet addr:192.168.1.70 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::21c:bfff:fe90:8a6d/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:77 errors:0 dropped:0 overruns:0 frame:0 TX packets:102 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:14256 (14.2 KB) TX bytes:14764 (14.7 KB) route: Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.2.0 * 255.255.255.0 U 1 0 0 eth1 192.168.1.0 * 255.255.255.0 U 2 0 0 wlan0 link-local * 255.255.0.0 U 1000 0 0 wlan0 default adsl 0.0.0.0 UG 0 0 0 eth1

  Read the article

• Computer loop restarts on Windows loading

  - by Robinson G.

  My computer restarts, just after or during Windows loading (4 squares getting together), or after some time on the desktop IF I'm idle. In order to start the computer I either have to swap my RAM (24Go) in differents DIMM slots, for example (I have 4 slots) : 1-2-4 or 2-3-4 or 1-3-4, not the same position each boot or it restarts in a loop... I can also change the ram timing from 1.5 to 1.6V and it starts, at the next reboot I have to change it again to 1.5 or it won't boot... And If after all, I succeed to boot, I have to use the computer for about 10 minutes, and it's ok, if I don't, it restarts by itself after some minutes. If I stay on the BIOS, It's all OK, I can stay for a whole year without restarting. I have check my RAM on Memtest (4*8G SDRAM DDR3) : OK I have check without graphic card : Still the same. I tried to reset the bios stack by getting it off and on : Still the same. I tried to reset my BIOS, and many settings about the RAM in the menu : Still the same. CPU temps are just fine (around 35°C) I was thinking ofc about the motherboard but I want to be sure. Motherboard : MSI zh77a-g43 RAM : 4*8G Dual Mode or not (depends on the number I put ofc.) PSU : 600W (enough to run all the config) CPU : i7 3770 non K

  Read the article

• Disable internal display on Macbook Pro without closed lid mode?

  - by jslaker

  I have an early 2007 Macbook Pro running 10.5 that I've recently set up on a KVM with my primary desktop system. The problem I've run into is that I have a 20" 1680x1050 LCD, and OS X only provides options to mirror at the resolution of the built-in display or to span. Since the built-in display runs at 1440x900, this leads to running my LCD at non-native res and a fuzzy picture. There isn't any option that I can find to simply disable the built-in display entirely and run the external LCD at its native resolution. I am aware of closed lid mode, but the MBP was disassembled while in storage for about 6 months (took it apart to pull the HDD) and the cable to the touchpad, which controls the sleep sensor was damaged, meaning closed lid mode won't work. I've looked into replacing the cable, but the cheapest I've been able to find it is $75-100, and I'm trying not to invest any more money into this computer as it also has a completely dead battery and a few other minor problems. I've found the app SwitchResX which appears to allow you to do what I need, but it has a lot of functionality I don't need and a ~$20 registration charge attached to it. An odd set of circumstances, I'm aware, but I was hoping somebody might know of an OS hack that would let me just disable the internal display and be done with it. :)

  Read the article

• Can I autoregister my servers hostname in my local DNS? [on hold]

  - by Christian Wattengård

  We have evaluated a W2k12 server as a domain controller at work. This has the extra benefit of registering every "subordinate" computers name in it's DNS so that I don't have to go around remembering IP's all the time. (And it let's me easily run dhcp also on my "pop-up" dev-servers). We need to rework our work network for several odd reasons, and in this new scenario there was no money for an extra Windows 2012 license. We have at our disposal several old boxes that run linux quite well. Is it possible to set up a DNS-server-"appliance" that somehow autoregisters it's own hostname.. Scenario: Router (N66u) on 172.20.20.1. Runs DHCP on 172.20.20.100-200 range. Server [verdant] of a *nix flavor on 172.20.20.2 Laptop [speedy] of W8 flavor on DHCP assigned Laptop [canary] of W8 flavor on DHCP assigned Desktop [lianyu] of Ubuntu flavor on DHCP assigned What I would like is that all of the above servers (except possibly the router) would be available on verdant.starling.lan and canary.starling.lan and so on. This is how it works right now (except the Ubuntu box... I haven't cracked that one yet) because Windows just does this for you.. I would also be able to do this without any manual labor on the server. When I tell my box it's name is smoak it should "immediately" be available as smoak.starling.lan without any extra configuration on my part. How can I do this in a Linux (Ubuntu) environment?

  Read the article

• Installing Visual Studio Express on Windows 8.1

  - by robrene

  I've been trying to install the latest version of Microsoft Visual Studio Express from their website to toy around with the IDE and C# development in general. I have a relatively fresh and completely vanilla installation of Windows 8.1 Professional x64 for this purpose. I come from a Linux background, where installing software (especially software distributed by the maintainer of the OS) is usually done with package managers. First, I tried to look for Visual Studio in the Windows 8 Store. There was one entry, but it did not have an installation button. Instead, it redirected me to their website. From all the products listed under the "Download" section on their website, I decided Visual Studio 2013 Express for Windows Desktop was the best for me. I selected it and clicked on "Install now". An installer program downloaded, and I'm assuming that the installer downloaded the necessary files as it was running. When it was done, it asked for a reboot, to which I obliged. However, I can't seem to find the IDE installed anywhere? It doesn't show up anywhere in the Start menu interface. I can't find any executables that look like they might be the IDE in its installation folder. Running the installer again and selecting "Repair" does download some files, but after its requested reboot, nothing has changed. The only thing that I can find is an advertisement link to "Try other Visual Studio 2013 Products" in my start menu. I suppose my question is what I have to do to run Visual Studio 2013 Express on Windows 8.1? Am I not looking in the right places? Am I doing the installation process wrong? Thanks in advance

  Read the article

• Windows 7 SSH file server

  - by Siriss

  Hello all- I have looked at the other posts, but have not quite found an answer I have a question about windows file sharing over SSH. I have copssh installed and it is working for Remote desktop connections. I have port 22 forwarded on my router etc. I connect from a Mac or Putty with this address: ssh -l copsshusername 3391:localhost:3389 [external ip] That works fine. I would like to configure Windows 7 to allow my ssh account that I use to login, access to certain shared folders. I have documents and videos and things that I would like to be able to download externally. I have done this before on Linux and a long time ago on XP, but I cannot figure out what I am missing on Windows 7. There is a designated SSH user that copssh uses to run the service and that I use to to login as. I have googled and googled and have not found a solution that does everything I need that is why I am turning here for ideas. I hope I am explaining this correctly. Thank you very much for your help!

  Read the article

• Shortcuts located in "D:\Program Data\..." not working even though they're pointing to the right targets (Windows 7)

  - by Kevin

  I just made a fresh install of my windows 7 home premium using my laptop's recovery disks (HP Pavilion dv6-2151cl) using minimal settings. After install, I set up "Program Data" and "Users" to my D partition to save space changing the folders in the registry. Then I updated windows (including W7 SP1), and installed all other programs. After installing all other programs I noticed that the icons of all new programs (not included in the windows install) in "All Programs" had a blank sheet as icon and they don't do anything. Looked into "D:\Program Data\Microsoft\Windows\Start Menu\Programs" in the windows explorer and the same is true there. All the shortcuts in C: and "D:\Users..." work both in the "Windows Explorer" and "All Programs". Also I noticed that the shortcuts do display the right icons inside the "open" dialog boxes. And if I copy the shortcuts in "D:\Program Data..." to the desktop they also work as expected. I checked file association for .lnk and it was OK, but also tried the registry fixers for this file association and they had no effect. There are no missing programs that I can tell in the "All Programs" menu, the just don't do anything if they lay in "D:\Program Data...". Any thoughts on how to make Windows 7 treat shortcuts in "D:\Program Data..." as they should?

  Read the article

• How do I get rid of these "There is a problem with your tablet driver" messages?

  - by Adam Rosenfield

  Every time I run certain applications (including but not limited to GIMP, Microsoft Visual Studio, and 3DS Max), I get the following message box: There is a problem with your tablet driver. Please reboot your system. If the problem persists reinstall or update the driver. Obviously I've tried rebooting and that hasn't fixed anything. Secondly, I'm not running a tablet PC. This is just Windows XP SP3 running on a Dell Precision PWS490 desktop workstation. How do I get rid of these error messages? The applications still load normally after dismissing them, but they're rather annoying. Using Process Explorer, I got the call stack from the message box. It's coming from wintab32.dll. Here's the call stack when running GIMP (irrelevant frames omitted): ... 8 USER32.dll!MessageBoxA+0x45 9 wintab32.dll!WTMgrPacketHookExA+0x44a 10 libgdk-win32-2.0-0.dll!gdk_display_list_devices+0x37 ... So, does anyone know how I can get an updated version of wintab32.dll or have any other ideas? I've been keeping my system up to date with Windows Updates. The timestamp on wintab32.dll is 2007-03-30 17:38, and its MD5 sum is ffdc332007c9dc6dd346c8ac2b09a015.

  Read the article

• Ubuntu 10.10 - disaster - what other linux for beginner?

  - by A-ha

  Guys, I've tried to install ubuntu (desktop and notebook ed) on my laptop and unortunately I have to say that as despite the fact that installation process supposed to be easy I couldn't finish installation of this system - didn't detect my keyboard or rather lost my keyboard as soon as I tried to switch on/off pad on my laptop. After I've discovered that, I started all over again (this time without touching my laptop's pad during installation) and yes, eventually it get to the end of installation. Unfortunately, when I've tried to switch my pad (sometimes I just do not want to use a mouse) the whole system froze. So I had to restart it with the power button and this time I didn't touch pad at all, plugged in mouse and tried to rearrange taskbars according to my liking (all taskbars on the top side of the screen and auto-hide on) and I gave up. It is so unfinished that I just can't be bothered to use it. I would like to have one linux system on my machine so I started googling and most of the links are to either ubuntu (which I just do not want to touch for now) and suse or commercial versions of linux. I do not really mind paying for something (and having experience with ubuntu I'd rather pay and have something pro then get it free and discover that it's unusable). So could someone please provide short list of linux distros which would be appropriate for a beginner, and I don't mind paying for it, I just want it to be a professional product.

  Read the article

• Windows won't boot after moving house. How do I solve this?

  - by James

  Ive just moved house and tried to set up my desktop after packing it away and now when I power it on, the BIOS boots up and no errors are found but when my computer tires to boot into Windows 7 a continuous fast beeping sound is made and a black screen is displayed. What I've done so far: Reset to UEFI defauts Played about with RAM, I had 4*4 GB sticks, I took all of them out to test for a mobo error which I have and now im only using 1 stick of 4 GB. Changed my GPU, I tok my gtx580 out and now im using the onboard Intel 3000 graphics driver, the BIOS and uefi are correctly displaying so I no longer think its a GPU based error. Ive check all of the connections and nothing seems to be loose. My HDD setup is: 2 128 GB SSD's in Raid 0 as my main C drive (possibly cause of error?) 1 1 TB Games drive 1 2 TB Data Drive Ive also got a blueray drive connected. After searching the internet im pretty much out of suggestions but im currently downloading a live CD to see if it will boot and if I can access some files on my HDD.

  Read the article

• Trouble setting up incoming VPN in Microsoft SBS 2008 through a Cisco ASA 5505 appliance

  - by Nils

  I have replaced an aging firewall (custom setup using Linux) with a Cisco ASA 5505 appliance for our network. It's a very simple setup with around 10 workstations and a single Small Business Server 2008. Setting up incoming ports for SMTP, HTTPS, remote desktop etc. to the SBS went fine - they are working like they should. However, I have not succeeded in allowing incoming VPN connections. The clients trying to connect (running Windows 7) are stuck with the "Verifying username and password..." dialog before getting an error message 30 seconds later. We have a single external, static IP, so I cannot set up the VPN connection on another IP address. I have forwarded TCP port 1723 the same way as I did for SMTP and the others, by adding a static NAT route translating traffic from the SBS server on port 1723 to the outside interface. In addition, I set up an access rule allowing all GRE packets (src any, dst any). I have figured that I must somehow forward incoming GRE packets to the SBS server, but this is where I am stuck. I am using ADSM to configure the 5505 (not console). Any help is very much appreciated!

  Read the article

• nVidia performance with newer X and newer driver abysmal with Compiz

  - by Nakedible

  I recently upgraded Debian to Xorg 2.9.4 and installed nvidia-glx from experimental, version 260.19.21. This was somewhat of an uphill battle as the dependencies for the experimental nvidia-glx package are still somewhat broken. I got it to work without forcing the installation of any packages and without modifying the packages. However, after the upgrade compiz performance has been abysmal. I am using the desktop wall plugin and switching viewports is really slow - takes a few seconds for each switch. In addition to this, every effect that compiz does, such as zoom animations for icons when launching applications, takes seconds. The viewport switching speed changes relative to the amount of windows on that virtual screen - empty screens switch almost at normal speed, single browser windows work almost decently, but just 4 rxvt terminals slows the switches down to a crawl. My compiz configuration should be pretty basic. Xorg is likewise configured without anything special - the only "custom" configuration is forcing the driver name to be "nvidia". I've fiddled around with the nvidia-settings and compizconfig trying different VSync settings, but none of those helped. My graphics card is: NVIDIA GPU NVS 3100M (GT218) at PCI:1:0:0 (GPU-0). This is laptop GPU that is from the Geforce GTX 200 series. Graphics card performance should naturally be no problem. EDIT: In the end, nothing really worked, and I got really annoyed with the state of compiz and its support in Debian. Many nVidia driver revisions have passed and I am using Gnome 3 now, so I am accepting the best answers to this question even though the issue was not resolved.

  Read the article

• Windows 7 BSOD on boot after windows update

  - by Razor Storm

  After Windows updates today, I restarted my desktop (for the first time in a couple weeks), and on boot up ran into a BSOD: STOP: 0x0000007E (0xFFFFFFFFC0000005, 0xFFFFF8000355AB5A, 0xFFFFF880031CB3A8, 0xFFFFF880031CAC10) I tried system restore, but there was only 1 restore point which was from all the way back in January. I tried it anyway but after 10 minutes of running it said system restore could not be completed. Additional info: I checked my BIOS and it is detecting my rams. CPU is Intel Sandy Bridge i5-2500k overclocked to 4.3GHz. I reclocked it back to stock speeds (3.3 GHz) in case it was causing the issue (I highly doubt that it is). But the problem persists. Running Windows 7. 12 GB of RAM at 1333 MHz OS on 64gb SSD. What is causing this? How should I fix it? Also, if it is caused by windows update, is there a way to undo the update with command prompt? I tried safemode, and the blue screen comes up as well, but I am able to access command prompt.

  Read the article

• How can I create a separate toolbar from the Task Bar?

  - by Iszi

  In Windows XP, you could separate toolbars from the Task Bar by dragging them to the desktop. They could then be left lying about anywhere on your screen or, my preferred option, docked to any side of the screen. I found this particularly useful to keep a handy list of common phone numbers quickly accessible. I'd create a new toolbar pointing to a custom folder, and put a bunch of dead shortcuts in the folder that had names and numbers as their file names. I'd then dock the toolbar to the left side, set it to auto-hide and always on top (options which could be set separate from the Task Bar as well) and it would be readily available no matter what else I was doing on my system. However, on my Windows 7 system, I seem unable to perform the crucial step of pulling the new toolbar off of the Task Bar. This is of course with the Task Bar "unlocked" so that I can move all my toolbars around. Is there something I'm missing here, or is this a feature that's been disabled in Windows 7? Is there any way to re-enable it, or otherwise achieve similar functionality? I'd rather be able to do this without additional software, if possible.

  Read the article

< Previous Page | 489 490 491 492 493 494 495 496 497 498 499 500  | Next Page >