Search Results

Search found 413 results on 17 pages for 'bateman ap'.

Page 5/17 | < Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >

• Issues getting a Cisco WLC 5508 to find AIR-LAP1142N

  - by user95917

  hoping someone can help me with a problem here. I'm attempting to setup a test (loan from Cisco) wireless network. Here's what i've got/done: 5508 Controller - Service Port IP set to 10.74.5.2 /24. Management IP set to 10.74.6.2 /24 with a default gateway of 10.74.6.1. Virtual IP set to 1.1.1.1. Copper SFP in slot 7, CAT5 (known good) going from there to port 1/0/47 on the switch. Green lights on both ends. 2960-S Switch - Vlan1 - 10.74.6.1 /24. dhcp pool 10.74.6.0 /24, default router 10.74.6.1. excluded-address 10.74.6.1, 10.74.6.2. 1/0/4 on the switch is set to switchport mode access and no shut. 1/0/47 on the switch is setup to switchport mode trunk and no shut. 1/0/4 has a CAT5 (known good) cable going from there to the AP. When I do a sh cdp nei from the switch, i can see the AP and Controller listed. When i configure my PC's nic to 10.74.5.5, and plug a cable from my nic to the SP port on the controller i can get on the device via the gui. In there, the only errors/info that show up in the trap are: Link Up: Slot: 0 Port: 7 Controller time base status - Controller is out of sync with the central timebase. I've manually set the time but apparently that's not quite the problem (or at least not the entire problem). When i plug the AP in, i see on the switch console that it grants it power, it sees it connect...but the controller won't see it for some reason. From what i've read you shouldn't have to do anything to the AP as it's managed by the controller...but i'm not sure what setting I'm missing for it to work. The AP light on top is continually cycling green, red, yellow. When I first start it up, it blinks green for 20 or so seconds, then goes to solid green for another 20 seconds or so, then flashes blue, green, red for awhile...but always ends up goinn back to the standard, green, red, yellow. Does anyone see any obvious issues with my setup or have any suggestions as to why i might be having a problem? Thanks for your help!

  Read the article

• What speed are Wi-Fi management and control frames sent at?

  - by Bryce Thomas

  There are a bunch of different 802.11 Wi-Fi standards, e.g. 802.11a, 802.11b, 802.11g, 802.11n etc. that all support different speeds. Wi-Fi frames are generally categorised as one of the following: Data frames - carry the actual application data Control frames - coordinate when its safe to send/reduce collisions Management frames - handle connection discovery/setup/tear down (e.g. AP discovery, association, disassociation) My question is about whether all these frames, and specifically management frames, are transmitted at the fastest supported speed available, or whether certain classes of frames are transmitted at some lowest common denominator speed. I have noticed that when I put an 802.11b/g only device into monitor mode and capture traffic over the air, I still see management frames (e.g. association/disassociation) being transmitted between my phone and AP which are both 802.11n, even though 802.11n has a higher transfer rate. So I am imagining one of two possibilities: My 802.11n phone/AP had to negotiate a slower speed for some reason and that's why I can see their frames on my 802.11b/g monitoring device. Management frames (and perhaps control frames also?) are sent at a lower speed, and it's only data frames that are transmitted faster with newer 802.11 standards. The reason I would like to know which one of these two possibilities (or perhaps a third possibility) is the case is that I want to capture management frames, and need to know whether using an 802.11b/g card is going to lead to me missing some frames sent at higher speeds than the monitoring card can observe. If management frames are indeed sent at a slower rate, then it's all good. If I just happen to be seeing the management frames because my phone/AP have negotiated a slower rate though, then I need to reconsider what card I use for packet capture.

  Read the article

• Wireless disconnects at random after upgrade to Ubuntu 10.4

  - by Daniel Elessedil Kjeserud

  After upgrading my home server from Ubuntu 8.10 to 10.4 my wireless seemingly drops out, even though my IRC client keeps it's connection to the servers, so it looks like the machine just stops taking wireless requests. A ping will give a me this Request timeout for icmp_seq 27 ping: sendto: Host is down After a while the machine just starts responding again, without any interaction from me. When the machine comes back, this is what dmesg gives me [ 18.296288] wlan0: direct probe to AP 00:1b:63:22:a4:5f (try 1) [ 18.296350] wlan0: deauthenticating from 00:1b:63:22:a4:5f by local choice (reason=3) [ 18.296440] wlan0: direct probe to AP 00:1b:63:22:a4:5f (try 1) [ 18.298697] wlan0: direct probe responded [ 18.298706] wlan0: authenticate with AP 00:1b:63:22:a4:5f (try 1) [ 18.306836] wlan0: authenticated [ 18.306886] wlan0: associate with AP 00:1b:63:22:a4:5f (try 1) [ 18.309396] wlan0: RX AssocResp from 00:1b:63:22:a4:5f (capab=0x411 status=0 aid=2) [ 18.309402] wlan0: associated [ 18.310187] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 18.447742] apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac) [ 18.447748] apm: overridden by ACPI. [ 19.163282] padlock: VIA PadLock not detected. [ 28.352022] wlan0: no IPv6 routers present kjes@brin:~$ lspci 02:07.0 Network controller: RaLink RT2561/RT61 rev B 802.11g It's on a wireless network with WPA2, the machine worked without any problems on the same wireless network since Ubuntu 8.10 was the most resent version, and there have been no changes to my network recently. Even though the server drops out, everything else on the network keeps working like normal.

  Read the article

• Wireless signal changes from strong to weak after connecting

  - by gibberish

  Router (primary AP) is a WRVS4400N, WAP (signal booster) is a WAP4410N. Problem: User is physically located within ten feet of WAP (200 feet from main wireless router). Signal is at 5 bars as user connects to wireless network. Within seconds, signal is at or below two bars and connection is poor. Background: Trying to solve problem of weak wireless signal in back offices. Desired result is for client laptops to automatically switch to the stronger signal. WAP is connected to network via Ethernet cable. WAP is set to AP mode (instead of Wireless Repeater mode) WAP does appear to boost signal. Using Windows 7 sys tray Connect To A Network applet, can observe signal boost as laptop approaches the WAP. Above-described problem happens to users located near or beyond the WAP. It does not happen to users in close proximity to the router. Secondary Question: If using WAP in AP Mode, do WAP and Router (primary AP) need to be on the same channel?

  Read the article

• Games consoles won't connect through the TP-Link TL-WA500G Access Point

  - by Manfred Wolff

  I hope that someone can help me. I have several Laptops and other devices, all using my Wireless Router (Sky Digital Netgear) To extend the range to the back of the house, I purchased a TP-Link TL-WA500G Range extender. configured just as a pure repeater, it picks up the signal from the Netgear Router. The Netgear Router does the DHCP, handing out the IP addresses. This all works a treat with several different laptops and my iPone4S, but when my son tries to use his XBox360, Sony Playstation3 or the Nintendo Wii those devices fail to acquire an IP address. They just sit their waiting for the IP config. This also happens with my wife's HTC desire ONE Android phone. My son says that, when his HTC Desire C won't get an IP address, he just unplugs the AP briefly - the phone will connect and he puts the AP back on. Once he is connected to the Router, the AP won't disturb function. The Games Consoles don't seem to work like that. They stop working, when the AP is reconnected. I had my son try to configure permanent IP addresses, and he said that did not work either, though I have to confirm that, as I did not see that for myself. Has anybody seen this before? I have searched the Net and have not found any similar problems anywhere. I wonder if there is setting somewhere that would fix this. Many thanks for anyone reading this and trying to help. M

  Read the article

• Meraki wireless access point disconnects clients

  - by resolver101

  We have a Meraki MR16 Cloud Managed AP and it disconnects certain clients. The clients with Intel wireless cards work without any disconnects. The Meraki reports the follow in its event log: Sep 4 09:55:47 WPA authentication Sep 4 09:55:47 802.11 association channel: 11, rssi: 64 Sep 4 09:55:38 802.11 disassociation client has left AP Sep 4 09:55:38 WPA deauthentication vap: 0, radio: 0, aid: 1633956416 An example wireless network card which the Meraki disconnects is Realtek RTL8191SE 802.11b/g/n WiFi Adapter. The realtek laptop is sat 2 meters away from the AP and has a lot of signal and the Meraki reports minimal interference. Any ideas why it disconnects non-intel wireless network cards?

  Read the article

• Wireless Network Issue, Disconnecting Randomly From Network

  - by Surfer513

  I'm having an odd problem with my wireless network. Here is the background information: Server (Windows Server 2008) 1 to 10 end user machines connecting to the network Layer 3 Access Point (Asus WL-330 gE) connected to ethernet of Server and all machines connect to the network via the AP The end user machines get a connection to the server with no problems initially. But then connections are randomly lost throughout the day to the server/network. The wireless NICs of the machines still see the wireless network but are unable to connect to it. Then after some time the connection is regained automatically. I initially thought there was a problem with this particular AP, but then I took the same make/model AP out of storage and still ran into the problem. Any ideas what could be causing this??? Very confusing that the wireless nics on the end user machines can still see the network but not connect, and that the connections are randomly lost/gained. Thanks in advance!

  Read the article

• Wireless Access Point - Can't ping other machines on the wireless network

  - by Surfer513

  I have a wireless access point (Netgear), and I have it setup so that it has an IP address in the current subnet (let's say 192.168.2.0, subnet mask of 255.255.255.0). The machine that it is connected to via ethernet cable has an IP in the same subnet as the AP. The machines that are connected to the AP via the wireless connection also have an IP address in the same subnet as the rest of the network (192.168.2.0). All machines can ping the access point, but they cannot ping each other. I don't totally understand why, because there is connection and all of the machines are in the same subnet. I realize this is a layer 3 device, but is there an issue because of this AP's lack of gateway capabilities? (i.e. no routing table, etc.)

  Read the article

• wireless network with cable modem and access point

  - by hayri

  I have a Scientific Atlanta EPC2203 cable modem and a TP-Link TL-WA500G access point. When I connect my computer directly to modem with a CAT5e cable I have internet connection on my laptop (when i type ipconfig i see my external ip there, provided by isp). So I decided to have wireless network in the flat, allowing other devices to connect as well. I bought this wireless ap (TL-WA500G) configured Wireless security stuff, and connected it to my modem. With that configuration (by default AP has static ip of 192.168.1.254) only my computer can connect to internet over wifi, but not any other device. When I set the IP of AP to Dynamic IP (DHCP) it is the same. How should I change my configuration to enable all wifi devices to connect to internet?

  Read the article

• Tiny linux box with 2xGbLAN, WLAN and 10MB/s AES throughput?

  - by Nakedible

  I'd like to find a small linux box with the following specifications: Small (mini-ITX size is OK) Fanless Runs Debian At least two gigabit network interfaces WLAN that supports "host ap" with hostapd + mac80211 in AP mode Can encrypt AES at least 10 megabytes per second Total cost $300 or less Solutions from multiple parts also accepted - I can buy an external network card etc. and build the box myself if the components are available. If you don't know about the "host ap" thing, just suggest your solution, I'll find out if I can get that resolved. If I can't get all that, I can possibly skip the "runs Debian" part, and I can definitely skip the hostapd part if the box can be a wireless access point with multiple ESSIDs out of the box. Something like Asus RT-N16 is close - doesn't run Debian easily, and probably doesn't encrypt AES fast enough. Something like Zotac ZBOX HD-ID11 is also close - no idea which WLAN card it has and it lacks second gigabit interface, but otherwise nice.

  Read the article

• Access points fighting for dominance?

  - by Phillip Oldham

  We have a small office with a large number of wireless devices (a mixture of desktop machines, laptops, and wifi-enabled phones) all working from a single Apple Airport Extreme which extends our wired network. I've added another Airport Extreme for resiliency, since we've been seeing a decrease in performance and (as far as I understand) access points can only handle a small number of clients. I set the new AP to extend the current network so that the clients weren't constantly switching between different wireless networks, however as soon as this AP was configured all the wireless devices started seeing network trouble, flicking on and off. I'm assuming that this is because both APs are reasonably strong, and the client can't decide which to use. What is the best route to follow to resolve this? What I'm aiming for is wireless resiliency; preferably having two APs share the network load, or if this isn't an option then having a primary AP with a "fail-over", should the primary go down for any reason.

  Read the article

• unreachable subnet in one direction

  - by Carl Michaud

  I'm unable to route traffic to a subnet in my home. Here's my topology: INET <- Router A <- Router B <- WIFI AP where: Router A - ARRIS TG862G/CT (from comcast) - WAN DHCP, LAN 10.0.0.99 Router B - Linksys WRT400N with DD-WRT - WAN 10.0.0.12 , LAN 10.0.1.1 I was able to use DD-WRT to configure a static route for the 10.0.1.x network back to the 10.0.0.x network. But I'm not sure if i can do the reverse on the ARRIS router and was looking for suggestions on how to fix that. I've set things up this wasy because I am using OpenDNS to mange internet content for my kids and of course I wasn't able to configure DNS to my liking on Router A either. So at present I'm using Router A on 10.0.0.x to provide a private unfiltered WIFI AP (no ssid broadcast) that I use for netflix only and then I use router B to provide a filtered WIFI AP for the rest of my WIFI devices on 10.0.1.x. However I would like to be able to connect to my 10.0.1.x devices from the internet via dynamic dns; but I can't see anything behind router B this way. Thoughts?

  Read the article

• wordpress php > div issue

  - by Philip Bateman

  Thanks in advance for you help Ive been doing this as a lovejob for friends and now im getting quotes of several hundred dollars for minor homepage variation and I'm not sure if its valid. I'm not a programmer myself, just trying hard :) Via the CafePress press75 theme, I'm trying to go from 1 / 2 / 3 column home layout, to 1-2 merged and 3, push the 2nd column data to the right and have the 1st column span as a 16:9 gallery (nextgengallery plugin installed). Is this really a complex thing from a coding perspective? The current guy talking to me is saying its going to cost $700 or 800 AUD to alter, which is rough when the template cost $85.. From this http://shocolate.com.au.previewdns.com/wp-content/uploads/2010/05/shocolatecurrent.jpg to this 'url+Shocolatelooklikethis.jpg' I was able to get the sidebar removed by taking out ‘‘ near the bottom of home.css.. Just can’t get the middle data to flow over it? This would be ideal as a result, as the system puts the latest selected blog post on the homepage, so if we can get rid of the sidebar div and have the text appear where it was, that would be ideal. Removing the sidebar from the bottom of home.php and setting the thumbnail width to say 450 gives me the result im after EXCEPT the text doesn’t fill where the sidebar is, it wraps underneath. Reference 'shocolate.com.au.previewdns.com' for current site Thank you!!! Phil (Melbourne)

  Read the article

• Problem with duplicates in a SQL Join

  - by Chris Ballance

  I have the following result set from a join of three tables, an articles table, a products table, an articles to products mapping table. I would like to have the results with duplicates removed similar to a select distinct on content id. Current result set: [ContendId] [Title] [productId] 1 article one 2 1 article one 3 1 article one 9 4 article four 1 4 article four 10 4 article four 14 5 article five 1 6 article six 8 6 article six 10 6 article six 11 6 article six 13 7 article seven 14 Desired result set: [ContendId] [Title] [productId] 1 article one * 4 article four * 5 article five * 6 article six * 7 article seven * Here is condensed example of the relevant SQL: IF EXISTS (SELECT * FROM sys.objects WHERE object_id = OBJECT_ID(N'tempdb.dbo.products') AND type = (N'U')) drop table tempdb.dbo.products go CREATE TABLE tempdb.dbo.products ( productid int, productname varchar(255) ) go IF EXISTS (SELECT * FROM sys.objects WHERE object_id = OBJECT_ID(N'articles') AND type = (N'U')) drop table tempdb.dbo.articles go create table tempdb.dbo.articles ( contentid int, title varchar(255) ) IF EXISTS (SELECT * FROM sys.objects WHERE object_id = OBJECT_ID(N'articles') AND type = (N'U')) drop table tempdb.dbo.articles go create table tempdb.dbo.articles ( contentid int, title varchar(255) ) IF EXISTS (SELECT * FROM sys.objects WHERE object_id = OBJECT_ID(N'articleproducts') AND type = (N'U')) drop table tempdb.dbo.articleproducts go create table tempdb.dbo.articleproducts ( contentid int, productid int ) insert into tempdb.dbo.products values (1,'product one'), (2,'product two'), (3,'product three'), (4,'product four'), (5,'product five'), (6,'product six'), (7,'product seven'), (8,'product eigth'), (9,'product nine'), (10,'product ten'), (11,'product eleven'), (12,'product twelve'), (13,'product thirteen'), (14,'product fourteen') insert into tempdb.dbo.articles VALUES (1,'article one'), (2, 'article two'), (3, 'article three'), (4, 'article four'), (5, 'article five'), (6, 'article six'), (7, 'article seven'), (8, 'article eight'), (9, 'article nine'), (10, 'article ten') INSERT INTO tempdb.dbo.articleproducts VALUES (1,2), (1,3), (1,9), (4,1), (4,10), (4,14), (5,1), (6,8), (6,10), (6,11), (6,13), (7,14) GO select DISTINCT(a.contentid), a.title, p.productid from articles a JOIN articleproducts ap ON a.contentid = ap.contentid JOIN products p ON a.contentid = ap.contentid AND p.productid = ap.productid ORDER BY a.contentid

  Read the article

• pointer to a structure in a nested structure

  - by dpka6

  I have a 6 levels of nested structures. I am having problem with last three levels. The program compiles fine but when I run it crashes with Segmentation fault. There is some problem in assignment is what I feel. Kindly point out the error. typedef struct { char addr[6]; int32_t rs; uint16_t ch; uint8_t ap; } C; typedef struct { C *ap_info; } B; typedef struct { union { B wi; } u; } A; function1(char addr , int32_t rs, uint16_t ch, uint8_t ap){ A la; la.u.wi.ap_info->addr[6] = addr; la.u.wi.ap_info->rs = rs; la.u.wi.ap_info->ch = ch; la.u.wi.ap_info->ap = ap; }

  Read the article

• Paid antivirus solutions for Windows

  - by AP Erebus

  NOTE: If your looking for recommendations on free antivirus, check this question: http://superuser.com/questions/2/free-antivirus-solutions-for-windows Much like the above, I'm curious to opinions on the best PAID antivirus solution, personal or commercial. Enterprise solutions are welcome and as much detail regarding costs is welcome. Personally I'm looking for a licence that will grant me more than 1 computer install and quality technical support, for personal use. as in the free antivirus question: See if your antivirus of choice is already listed. Chances are it is. If you spot an answer that mentions one you already use, vote that up if you think it's a good solution. If you know of a feature or drawback not listed, or can include experiences in dealing with it, please edit the answer accordingly. If you know of any that can also be used at work please point this out. This covers all Windows platforms from XP, Vista and Windows 7. If you see an existing entry that needs an update or to add your testimonial, please do.

  Read the article

• Setting up a software access point on Gigabyte GN-WPKG x64

  - by Reckage

  I'm using a Gigabyte GN-WPKG card on Windows 7 64-bit and was thinking it would be good to turn it into a wireless AP (I have a wired internet connection). Connectify, which would normally be the solution, says it's not compatible. There are instructions for setting up an AP, but they seem to be for 32-bit. I found the equivalent drivers for 7 and they don't seem to do anything. Is there no SoftAP for Vista and later on a Gigabyte card?

  Read the article

• D-Link DIR-300 slows down / loses network

  - by basic6

  Hi there, there are 2 buildings (A and B). In bldg A is an open WLAN (which I'm allowed to use btw). In bldg B is a computer that I want to connect to that network. So I flashed an old D-Link DIR-300 AP with DD-WRT, mounted it to the wall (bldg B) near a window, attached a 13 dBi directional antenna (pointing to bldg A) and configured it as AP client in that wireless network. Then there's another AP, connected to the D-Link AP, acting as standard access point, which the computer is connected to. That's basically working so far, but: Every now and then the connection is lost. Not the connection between the computer and the D-Link (I can access the DD-WRT admin page normally) or the connection between the D-Link and the WLAN (in Status - Wireless it says it's still connected to the network), but when I want to access a web page (which only works if I'm connected to the wireless network from bldg A), my Firefox keeps "Looking for" (name resolution) without finding anything. When I reset the D-Link (power off, power on) in this situation, after some moments, everything's working fine again (Internet access). I've no idea why this is happening, but usually it's at most every few weeks (most times when nobody was using the computer, so no traffic). Compared to the connection speed when I connect directly to the WLAN in bldg A (Laptop), the speed in bldg B is rather slow, but I have the impression that this difference is worse in the last few days. A few minutes ago, I got 582 KB/s down and 911 KB/s up in bldg A (directly/laptop) and 84 KB/s down and 9 KB/s up in bldg B. The speed in bldg B used to be way higher (I remember 200 KB/s up) while the actual network speed in bldg A was lower than it is now (close to those 200). I'm aware that the wireless connection between those buildings should slow things down, but I'm wondering why this difference has become that extreme. Thanks for any tips... Update: I currently want to upload a large file (1.5 GB) via FTP (FileZilla). Since that caused the D-Link to disconnect (as described in first post), I took my laptop to bldg A, connected directly to the original WLAN (bypassing my D-Link) and tried the same upload. Guess what - same issue: At some point the connection is dead (at this point I would have reset my D-Link if I was connected to it). Just as the D-Link, my laptop is still connected, but not even name resolution is working ("Looking for..." in Firefox). After reconnecting, it's working again. Maybe my D-Link isn't the problem at all...

  Read the article

• Sonicwall 3500 (Creating VLANS for usage of multiple SSID)

  - by Thomas Chia

  I have an issue here. Here is my setup: X0 - STAFF network | X2 - AGENT network | X4 - Wireless AP (for multiple SSID) Okay, basically I'm going to set up the wireless AP to be broadcasting 2 SSID, STAFF-WIFI and AGENT WIFI. When connected to STAFF-WIFI, the users will be connected to the STAFF network, while connected to the AGENT WIFI, the users will be connected to the AGENT network. Can someone explain in details how to go about setting up this configuration? Thanks!

  Read the article

• Multiple access points for the same SSID ?

  - by krosenvold

  I need to upgrade my existing wireless infrastructure and this time I want 2 access points to cover my house, since I get blind spots no matter what with a single AP, I have physical cabling to my central network available for both access points. But I would really like these two to interoperate seamlessly as a single SSID. How do I do this and what are the features the new AP's I'm buying need to support ? (Product recommendations are welcome ;)

  Read the article

• Wifi interference tool for Mac

  - by Kevin Burke

  This Server Fault blog post shows some tools you can use to view interference on your wireless network: blog.serverfault.com/2012/01/05/a-studied-approach-at-wifi-part-2/. They mention Vistumbler, which only works on PC's. Is there a similar tool I can use to measure wireless interference on a Mac? Also, is it better to be on a channel with many AP's, each with a weak signal, or on a channel with only a few AP's, but a strong signal?

  Read the article

• D-Link DIR-300 slows down / loses network

  - by basic6

  there are 2 buildings (A and B). In bldg A is an open WLAN (which I'm allowed to use btw). In bldg B is a computer that I want to connect to that network. So I flashed an old D-Link DIR-300 AP with DD-WRT, mounted it to the wall (bldg B) near a window, attached a 13 dBi directional antenna (pointing to bldg A) and configured it as AP client in that wireless network. Then there's another AP, connected to the D-Link AP, acting as standard access point, which the computer is connected to. That's basically working so far, but: Every now and then the connection is lost. Not the connection between the computer and the D-Link (I can access the DD-WRT admin page normally) or the connection between the D-Link and the WLAN (in Status - Wireless it says it's still connected to the network), but when I want to access a web page (which only works if I'm connected to the wireless network from bldg A), my Firefox keeps "Looking for" (name resolution) without finding anything. When I reset the D-Link (power off, power on) in this situation, after some moments, everything's working fine again (Internet access). I've no idea why this is happening, but usually it's at most every few weeks (most times when nobody was using the computer, so no traffic). Compared to the connection speed when I connect directly to the WLAN in bldg A (Laptop), the speed in bldg B is rather slow, but I have the impression that this difference is worse in the last few days. A few minutes ago, I got 582 KB/s down and 911 KB/s up in bldg A (directly/laptop) and 84 KB/s down and 9 KB/s up in bldg B. The speed in bldg B used to be way higher (I remember 200 KB/s up) while the actual network speed in bldg A was lower than it is now (close to those 200). I'm aware that the wireless connection between those buildings should slow things down, but I'm wondering why this difference has become that extreme. Thanks for any tips... Update: I currently want to upload a large file (1.5 GB) via FTP (FileZilla). Since that caused the D-Link to disconnect (as described in first post), I took my laptop to bldg A, connected directly to the original WLAN (bypassing my D-Link) and tried the same upload. Guess what - same issue: At some point the connection is dead (at this point I would have reset my D-Link if I was connected to it). Just as the D-Link, my laptop is still connected, but not even name resolution is working ("Looking for..." in Firefox). After reconnecting, it's working again. Maybe my D-Link isn't the problem at all...

  Read the article

• Getting IP Address of Access Point.

  - by andreas

  Hi Folks, recently I turned my Router to a wireless access point for my home network. Unfortunately, I forgot to note down the AP's IP Address and Subnet. How do I reliably get the IP of my AP? Thank's in advance.

  Read the article

• How to know a file is finished copying

  - by Yigang Wu

  I’m using ReadDirectoryChangesW to spy a folder, if I’m copying a large file to the folder, I can receive multiple FILE_ACTION_MODIFIED messages, it seems each time windows writes a large chunk of the file, you get the file modified notification for each time. I tried to use CreateFile API to check if the file can open by AP or not, but sometime, some of files are always locked by other AP, for example, if you are opening the Outlook, the PST will update, but my AP can’t access it, we have to start Shadow Copy to open it. So my question is, how to know a file is finished copying?

  Read the article

• How to get the SMTP response in CACHE

  - by praveenjayapal

  Hi friends, I want to retrive the SMTP response after sending the mail. I need to fetch the response for the send mail (whether its send properly or not) The response must be like this Return-path: itgigs@4wtech.com Envelope-to: [email protected] Delivery-date: Fri, 12 Dec 2008 23:54:57 -0500 Received: from pool-98-109-89-94.nwrknj.fios.verizon.net ([98.109.89.94] helo=Andy-PC) by server.4wtech.com with esmtp (Exim 4.69) (envelope-from itgigs@4wtech.com) id 1LBMWn-0005BH-7u for [email protected]; Fri, 12 Dec 2008 23:54:57 -0500 Date: Sat, 13 Dec 2008 04:55:09 UT From: [email protected] Subject: Web Deverloper Internship (SoHo) (955259288 ) To: [email protected] MIME-Version: 1.0 Content-Type: text/html; charset="ISO-8859-1" Content-Transfer-Encoding: quoted-printable How can i retrieve the SMTP response? Please help me

  Read the article

< Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >