Search Results

Search found 31973 results on 1279 pages for 'network library'.

Page 502/1279 | < Previous Page | 498 499 500 501 502 503 504 505 506 507 508 509  | Next Page >

  • NAT and ISP Subnet when load balancing on pfsense?

    - by dannymcc
    I have a pfsense box that I'm trying to plan the configuration for. I am going to be load balancing two ISP's, each with their own /29 static IP subnet. The question I have is in relation to the way those IP's are associated with workstations on the local network. Currently I have some workstations with local (192.168.1.0/29) IP addresses, and other more complicated workstation setups have their own public IP address. Some of the more complicated systems have a NAT 1:1 configuration where I forward a public IP address to a local IP address. Others however are directly on the ISP subnet and cannot be seen on our local network. Is this configuration possible with pfsense? If so, what terms should I be looking through the documentation for? Here is a simple/brief diagram of what I am trying to achieve.

    Read the article

  • Access my mac's local server from a windows machine

    - by Simon Davies
    I am running my test sites on my mac, but I would like be able to use my windows machine to also access this server and be able to write / read fiels form this server. I can access my sites on my windows by using the IP address 192.168.1.???. But I would like to be able to use my windows machine to also access the fiels and edit them. Any ideas much appreciated. Some details: Mac OSX SL file sharing set to on. Windows 7 (tried setting up network map using afp://192.... but nothing) Both machines are connected to a local network, with several other machine (windows) Thanks

    Read the article

  • Routing Essentials

    - by zharvey
    I'm a programmer trying to fill a big hole in my understanding of networking basics. I've been reading a good book (Networking Bible by Sosinki) but I have been finding that there is a lot of "assumed" information contained, where terms/concepts are thrown at the reader without a proper introduction to them. I understand that a "route" is a path through a network. But I am struggling with visualizing some routing-based concepts. Namely: How do routes actually manifest themselves in the hardware? Are they just a list of IP addresses that get computed at the network layer, and then executed by the transport? What kind of data exists in a so-caleld routing table? Is a routing-table just the mechanism for holding these lists of IP address (read above)? What are the performance pros/cons for having a static route, as opposed to a dynamic route?

    Read the article

  • How do I set zone priority in Microsoft DNS?

    - by Justin
    I have a standard small network setup (20 users) on Active Directory. All Windows machines have a primary DNS server as the AD and a secondary DNS server as Google PDNS. I want to setup a DNS entry that exists in real DNS but set it up on our DC so that local requests would route this public domain to a local development machine on the network. I setup the zone in DNS which results in the clients resolving the public FQDN to our internal IP. However, sometimes it still resolves to the "real" value (I check by pinging it). Is there some way to give the zone definition in my DC DNS higher priority? Or will the client that has secondary public DNS always at sometimes have a competing entry for this zone?

    Read the article

  • Slow LAN transfer from 3rd party computer

    - by Chris
    Hi Everyone, I've got an odd problem that I'm not really sure where to start the troubleshooting process. I have a 'server' with Windows Server 2008R2 (64-bit) installed and it has a couple of hard drives. If I Remote Desktop into the server and transfer files from one HD to the other, all it fine. If however, I use my workstation (Windows 7 64bit) and open up a shared resource on the server and transfer a file from one hard drive on the server to another HD on the server (not using Remote Desktop, just Windows explorer/Network places), the transfer crawls... It takes about 5mins to discover files/calculate the transfer and then starts transferring at speeds like 56KB/s - 200KB/s. Both machines have Marvel GigE network ports with a TrendNet 8-port green GigE switch. I've set Jumbo packets to 9K on both machines...

    Read the article

  • Naming your website longname.com vs shortcatchy.net vs shortcatchy.info

    - by jskye
    I'm designing a website that will basically be a social network for sharing information. I have the domain $$$$d.net and the same domain $$$$d.info where $$$$ is a word (that runs into the d) pertaining to the purpose of the site . The .com of this domain was already taken, but they've got nothing showing. They only have a not reached google error showing ie. dont seem to be trying to sell it either. I also have the long name of the site $$$$------&&&&&&&&&.com where the words $$$$ and &&&&&&&&& would contribute relevant seo to the site. In fact the word $$$$------ would also if a one letter spelling mistake is recognised at all by google, which i doubt but am unsure about. But as a brandname the $$$$------ word still works relevantly. Which do you think is a better choice to use? The short catchy name with the .info for relevance to information The .net which is more familiar than .info but slightly less relevant maybe. (But i think net as in network still works cos as i said it will be a social networking site). The long, .com domain which has more SEO plus a pun albeit on a spelling mistake. I know its kind of a subjective question and also hard to answer without knowing the name (which I've obfuscated because I'm only in initial design stage) but nevertheless im interested in what some of you guys think.

    Read the article

  • IPv6 6to4 on Windows Server

    - by Graham Wager
    I'm looking for a relatively simple guide to setting up an IPv6 tunnel properly. This network currently has a server (Windows Server 2008R2) running RRAS that establishes connectivity to the internet using a demand-dial PPPoE connection and handles the NAT. It also hosts a DNS server and DHCP. My ISP does not support IPv6, but I have a static IPv4 address. I've read about 6to4 and signed up at tunnelbroker.net, but quickly felt out of my depth. How do I configure my network to use it, and how I should configure my DHCP server with regards to IPv6 addresses?

    Read the article

  • Configure IIS 6 to deny access to specific file based upon IP address

    - by victorferreira
    Hello guys, We are using IIS 6 as our webserver. And we need to deny the access for one specif file, placed in only one specific URL, to everybody OUTSIDE the local network. In other words, if somebody is trying to access that filme/page from their own computer at home, using the internet, they must not succeed. But, if the same person try to do that at the same network of the web server, its ok. I am not sure about that, but Apache uses ORDER DENY,ALLOW. You specify the URL, allow or deny to all or to a range of IP. Any suggestions? Thanks!

    Read the article

  • Is it possible to add tcp autotuning to windows xp?

    - by Caspin
    I have a network application that needs to send messages at 60 times a second. The messages are usually 300-400 bytes, but can be as large as 1500. The default setting for SO_SNDBUF is too small and limits the number of message that can be sent if the network latency is anything greater then 100ms. The naive solution is to just bump the SO_SNDBUF size to to something large. However, depending on the latency and the packet size that could be anywhere from 64K to 8MB. One of Vista's new features is TCP autotuning. Autotuning monitors the tcp connection and dynamically adjust the buffer sizes to allow for optimal communication. I would like to use auto tuning on our windows xp machine so I don't need to guess what my buffers sizes should be. Is there a way to install either a microsoft or 3rd party tcp autotuner on windows xp?

    Read the article

  • Is it possible to add tcp autotuning to windows xp?

    - by Caspin
    I have a network application that needs to send messages at 60 times a second. The messages are usually 300-400 bytes, but can be as large as 1500. The default setting for SO_SNDBUF is too small and limits the number of message that can be sent if the network latency is anything greater then 100ms. The naive solution is to just bump the SO_SNDBUF size to to something large. However, depending on the latency and the packet size that could be anywhere from 64K to 8MB. One of Vista's new features is TCP autotuning. Autotuning monitors the tcp connection and dynamically adjust the buffer sizes to allow for optimal communication. I would like to use auto tuning on our windows xp machine so I don't need to guess what my buffers sizes should be. Is there a way to install either a microsoft or 3rd party tcp autotuner on windows xp?

    Read the article

  • PHP compiled on Mac OSX 10.6 - using /usr/lib when trying to start apache... rather than /opt/local/lib specified when php was configured

    - by Anthony
    PHP 5.3.3 compiled on Mac OSX 10.6 - using /usr/lib when trying to start apache... rather than /opt/local/lib specified when php was configured Why is it trying to load from /usr/lib when I specified in my configure not to? httpd: Syntax error on line 115 of /private/etc/apache2/httpd.conf: Cannot load /usr/libexec/apache2/libphp5.so into server: dlopen(/usr/libexec/apache2/libphp5.so, 10): Library not loaded: /opt/local/lib/libiconv.2.dylib\n Referenced from: /usr/libexec/apache2/libphp5.so\n Reason: Incompatible library version: libphp5.so requires version 8.0.0 or later, but libiconv.2.dylib provides version 7.0.0 The error message above refers to /opt/local/lib which when I run: otool -LD /opt/local/lib/libiconv.2.dylib /opt/local/lib/libiconv.2.dylib: /opt/local/lib/libiconv.2.dylib (compatibility version 8.0.0, current version 8.0.0) /usr/lib/libSystem.B.dylib (compatibility version 1.0.0, current version 125.0.0) It shows that the version is different than what http is erring out as.

    Read the article

  • Simple NAT router for ESX

    - by Evan M.
    Hi Guys, I'm looking for a simple virtual appliance that I can deploy to my ESX environment to use as a virtual NAT router / firewall to create an isolated network that I can easily give internet access too. Basic setup: ESX Host, has 2 vswitches configured: 1 is connected to the physical LAN, the other is isolated. I need an appliance that I can add 2 vNICs to, and attach one to the isolated vSwitch, the other to the LAN, to give the isolated network outbound access (so it can reach the internet). Anyone have an appliance that I can setup quickly to do so? Thanks.

    Read the article

  • Is there an alternative to SDL 1.3 for a C++ game that should run on iOS and Android?

    - by futlib
    I've used SDL for many desktop games, always as the cross-platform glue for: Creating a window Processing input Rendering images Rendering fonts Playing sounds/music It has never disappointed me at those tasks. But when it comes to graphics, I prefer to work with the OpenGL API directly, even though all of our games are 2D. In the project I'm currently working on, I've made sure to only use the API subset supported by both OpenGL 1.3 and OpenGL 1.0, so making the thing run on Android should be easy, I thought. Turns out there is no official Android or iOS port of SDL yet. However, there's one in SDL 1.3, which is still in development. SDL 1.3 doesn't seem very appealing to me for three reasons: It's been in development for at least 4 years, and I have no idea when it will be done, not to mention stable. It's not ported to as many platforms as SDL 1.2. From what I've seen, it uses OpenGL for drawing, so I suppose the community will move away from directly using OpenGL. So I'm wondering if I should use a different library for our current project - it doesn't matter much if I need to port my existing code from SDL 1.2 to SDL 1.3 or to some other library. We're planning to release on Windows, Mac OS X, Linux, iOS and Android, so good support for these platforms is essential. Is there anything stable that does what I want?

    Read the article

  • Application toolkits like QT versus traditional game/multimedia libraries like SFML

    - by Aaron
    I currently intend to use SFML for my next game project. I'll need a substantial GUI though (RPG/strategy-type) so I'll either have to implement my own or try to find an appropriate third party library, which seem to boil down to CEGUI, libRocket, and GWEN. At the same time, I do not anticipate doing that many advanced graphical effects. My game will be 2D and primarily sprite-based with some sprite animations. I've recently discovered that QT applications can have their appearance styled so that they don't have to look like plain OS apps. Given that, I am beginning to consider QT a valid alternative to SFML. I wouldn't have to implement the GUI functionality I'd need, and I may not be taking advantage of SFML's lower-level access anyway. The only drawbacks I can think of immediately are the learning curve for QT and figuring out how to fit game logic inside such a framework after getting used to the input/update/render loop of traditional game libraries. When would an application toolkit like QT be more appropriate for a game than a traditional game or multimedia library like SFML?

    Read the article

  • UDP multicast streaming of media content over WIFI

    - by sajad
    I am using vlc to stream media content over wireless network in scenario like this (from content streamer to stream receiver client): The bandwidth of wireless network is 54 Mb/s and UDP stream's required bandwidth is only 4 Mb/s; however there is trouble in receiving media stream and quality of playing specifically in multicast mode; means I can play the stream but it has jitter and does not play smoothly. In uni-cast I can stream up to 5 media streams correctly, but in multicast mode there is problem with streaming just one media! However when I stream from client some multicast streams; the wifi access-point can receive data correctly and I can see the video in "udp streamer" side correctly even when number of multicast streams increases to 9; But as you see I want to stream from streaming server and receive media in client size. Is this a typical problem of streaming real-time contents over wireless networks? Is it necessary to change configurations of my WIFI switch or it is just a software trouble? thank you

    Read the article

  • What do you wish language designers paid attention to?

    - by Berin Loritsch
    The purpose of this question is not to assemble a laundry list of programming language features that you can't live without, or wish was in your main language of choice. The purpose of this question is to bring to light corners of languge design most language designers might not think about. So, instead of thinking about language feature X, think a little more philisophically. One of my biases, and perhaps it might be controversial, is that the softer side of engineering--the whys and what fors--are many times more important than the more concrete side. For example, Ruby was designed with a stated goal of improving developer happiness. While your opinions may be mixed on whether it delivered or not, the fact that was a goal means that some of the choices in language design were influenced by that philosophy. Please do not post: Syntax flame wars (I could care less whether you use whitespace [Python], keywords [Ruby], or curly braces [Java, C/C++, et. al.] to denote program blocks). That's just an implementation detail. "Any language that doesn't have feature X doesn't deserve to exist" type comments. There is at least one reason for all programming languages to exist--good or bad. Please do post: Philisophical ideas that language designers seem to miss. Technical concepts that seem to be poorly implemented more often than not. Please do provide an example of the pain it causes and if you have any ideas of how you would prefer it to function. Things you wish were in the platform's common library but seldom are. One the same token, things that usually are in a common library that you wish were not. Conceptual features such as built in test/assertion/contract/error handling support that you wish all programming languages would implement properly--and define properly. My hope is that this will be a fun and stimulating topic.

    Read the article

  • Can a switch consume bandwidth?

    - by aashiq
    I have a network with a router and a switch. At first my ISP's optical fiber is connected with media converter input port. Than Ethernet cable (output port of Media converter) is connected with the switch. Then an output Ethernet cable is connected with our inner Microtik router. Then this router is connected with another LAN switch. From this switch we have got every connection other switch. It is our total network structure. Our bandwidth is 2 Mbps. From the 11th of March our MRTG graph shows high all the time even when my all switch is switched off except LAN switch. That's why our line is breaking up (Voice call). How could be it possible? My all PC's bandwidth is limited but when connected PC with media converter directly then the graph shows normal. That's why I can't blame my ISP.

    Read the article

  • I created a program based on an LGPL project, and I'm not allowed to publish the source code

    - by Dave
    I thought LGPL was a permissive license, just like MIT, BSD or Apache. But today I read, that only linking to LGPL (libraries etc) is allowed from closed-source code - other than that, it's copyleft - so I have to publish code that is based on an LGPL program. I created a program for my employer that is based on an LGPL program, but has considerable modifications to it. Of course, I am not allowed to put that modified source code out there. At the same time, I have to, if I distribute it (right?). So I wonder whether there is a workaround to this, so I can keep this closed-source (I wish I could publish the source) - any suggestions? My idea: can I put most functions of the original LGPL app into an external library, write the core executable from scratch, but refer back to the library for all functions that I haven't modified? Currently, everything is in a .jar file (it's Java/Swing). if you think my idea is legally/technically feasible - how much effort would it be to seperate what I wrote and what the original is? I'm not the most java savvy.

    Read the article

  • 12.04 WiFi issue on a particular access point

    - by user71706
    I have a WiFi access point that I connect to a PC to share its Internet connection with multiple machines, in a training environment. All the machines with 11.04 connect to this access point with no problem, and can access any server on the Internet. These machines have an Intel Wireless -N 1030 BGN chipset (as reported by lspci). Now, my problem is that I don't manage to connect 12.04 machines to this wireless network. The systems I tried do manage to connect (confirmed by Network Manager), but when I try to access a website like http://kernel.org, the browser shows "Connecting to kernel.org...", but displays a "The connection has timed out" error page. Other symptoms: Name resolution works (for example 'nslookup kernel.org') finds kernel.org's IP address 'ping kernel.org' doesn't work The same 12.04 machines have no problem at all with other wireless networks. So there is probably something weird in my access point (though the 11.04 machines are not impacted). Would you have any suggestions for investigating this issue? Thanks, Michael.

    Read the article

  • Will disabling NAT on my wireless router cause a performance hit on my DSL router?

    - by user117313
    I have a Thomson TG508v2 router/modem and a brand new AirPort Extreme connected to it. At first, I set the AirPort Extreme to "share a public IP", which enables DHCP/NAT. Everything works great but I was having the Double NAT error. So I set the AirPort Extreme as bridge mode, which disables DHCP/NAT and let my crappy modem handle my internal network IPs. Will this cause any performance hit in my network? I'm worried because I'll outsource this job from AirPort Extreme (premium hardware) to the crappy modem. Before you suggest, I tried setting my modem as a bridge and configuring PPPoE on the AirPort Extreme, however it wouldn't connect to the internet, so I just dismissed leaving the modem as bridge.

    Read the article

  • Win 7: Share internet connection via Ethernet and WiFi

    - by Anvaka
    I have the following configuration: Box 1. Running Win 7, connected to the Internet via Eth0. Has one wireless network adapter and one another ethernet adapter (say, Eth1). Box 2. Running Win XP, has one ethernet adapter. I'd like to share Internet connection of the Box 1 with Box 2 via cable and have box 1 also sharing the Internet with other wireless devices. I don't want to buy any additional hardware. Is it possible? PS: Sorry if I'm unclear. I merely know nothing about NAT and network administration.

    Read the article

  • Win 7: Share internet connection via Ethernet and WiFi

    - by Anvaka
    I have the following configuration: Box 1. Running Win 7, connected to the internet via Eth0. Has one wireless network adapter and one more ethernet adapter (say, Eth1). Box 2. Running Win XP, has one ethernet adapter. I'd like to share Internet connection of the Box 1 with Box 2 via cable and have box 1 also sharing the Internet with other wireless devices. I don't want to buy any additional hardware. Is it possible? PS: Sorry if I'm unclear. I merely know nothing about NAT and network administration

    Read the article

  • Need advice on framework design: how to make extending easy

    - by beginner_
    I'm creating a framework/library for a rather specific use-case (data type). It uses diverse spring components, including spring-data. The library has a set of entity classes properly set up and according service and dao layers. The main work or main benefit of the framework lies in the dao and service layer. Developers using the framework should be able to extend my entity classes to add additional fields they require. Therefore I made dao and service layer generic so it can be used by such extended entity classes. I now face an issue in the IO part of the framework. It must be able to import the according "special data type" into the database. In this part I need to create a new entity instance and hence need the actual class used. My current solution is to configure in spring a bean of the actual class used. The problem with this is that an application using the framework could only use 1 implementation of the entity (the original one from me or exactly 1 subclass but not 2 different classes of the same hierarchy. I'm looking for suggestions / desgins for solving this issue. Any ideas?

    Read the article

  • How to set up a file server in a restricted corporate environment

    - by Emilio M Bumachar
    I work in a big corporation, and the disk space my team gets in the corporate file server is so low, I am considering turning my work PC into a file server. I ask this community for links to tutorials, software suggestions, and advice in general about how to set it up. My machine is an Intel Core2Duo E7500 @ 3GHz, 3 GB of RAM, Running Windows XP Service Pack 3. Upgrading, formatting or installing another OS is out of the question. But I do have Administrator priviledges on the PC, and I can install programs (at least for now). A lot of security software I don't even know about is and must remain installed. But I only need communication whithin the corporate network, which is not restricted. People have usernames (logins) on the corporate network, and I need to use them to restrict access. Simply put, I have a list of logins of team members, and only people in the list should access the files. I have about 150 GB of free disk space. I'm thinking of allocating 100 GB to the team's shared files. I plan monthly backups on machines of co-workers, same configuration. But automation of backups is a nice, unnecessary feature: it's totally acceptable for me to manually copy the contents to a different machine once a month. Uptime is important, as everyone would use these files in their daily work. I have experience as a python and C programmer, but no experience whatsoever as a sysadmin, and almost nothing of my programming experience is network programming. I'm a complete beginner in this. Thanks in advance for any help. EDIT I honestly appreciate all the warnings, I really do, but what I plan to make available is mostly stuff that now is solely on DVDs just for space reasons. It's 'daily work' to read them, but 'daily work write' files will remain on the corporate server. As for the importance of uptime, I think I overstated it: a few outages are OK, it's already an improvement over getting the DVDs. As for policy, my manager is kind of on my side, I will confirm that before making my move. As for getting more space through the proper channels, well, that was Plan A, and it's still on the table... But I don't have much hope. I'm not as "core businees" as I'd like.

    Read the article

  • Mac OS X Snow Leopard hangs after login

    - by sleepyjames
    After restoring from backup following filesystem corruption my user account hangs after login (After entering my password the login window disappears and all I get is the background and a mouse pointer, no spinning wheel of death etc ..) I can login as a different user and then logout and login as my main account (sometimes!) but this is not consistant. I can login with safemode ok and have tried deleting /System/Caches, ~/Library/Caches and removing all my ~/Library/Preferences which worked once but not again. Does anyone have an any idea which logs I can look in, if any, to see whats happening after login or any other tips? I'm using 10.6.2. Cheers.

    Read the article

< Previous Page | 498 499 500 501 502 503 504 505 506 507 508 509  | Next Page >