Search Results

Search found 16174 results on 647 pages for 'disk space'.

Page 524/647 | < Previous Page | 520 521 522 523 524 525 526 527 528 529 530 531  | Next Page >

• Best option for storage clustering

  - by sam

  I'm working on an application that requires a large amount of storage space and I want to handle storage 'in-house' (Much cheaper than, say, S3) so we will have multiple servers (Initially 4) with large amounts of storage (6TB each). The storage will need to be very flexible and configurable, each piece of data should be replicated on at least 2 servers and must be easily readable/writable from ether an API of a UNIX device/file/folder like a normal drive, I don't mind which. We must also be able to easily offload content to our HTTP CDN (Edgecast), it doesn't need to have built in HTTP support but if it doesn't I'm going to have to write something to get the files onto HTTP so they can be pulled by the CDN. I've looked at a lot of solutions including Eucalyptus Walrus OpenStack Object Storage MogileFS and some others which I can't remember All the servers will be running RHEL 6, they have 4x1.5TB drives which will be RAID1'd into a single partition. All the servers have 1GB/s connections between them and 100MB/s connections to the internet with unlimited bandwidth. They have 2x2.66ghz processors. I understand there isn't a single, perfect answer but it would be nice to get some pointers.

  Read the article

• Files not being copied to AFP volume when copying through the Finder

  - by cefstat

  I am trying to copy files from my Macbook's hard disk to my NAS. The latter is a ReadyNAS Duo and is mounted as an AFP volume. The files are about 5MB each and I copy them by selecting in a Finder window all the files that I need and then dropping them onto the destination directory. Almost always some of the files do not get copied to the NAS. For example, if I select 200 files and then start the copying, everything looks at the beginning normal (while the copying takes place the Finder window for the destination directory is updated to show 200 files while it was empty before), but after the copying ends the destination directory shows less than 200 files (let's say 190). If I copy again the same 200 files to the NAS, without replacing already copied files, the remaining 10 files are usually copied correctly. In a few cases, I have to repeat the process a third time. Notice that the Finder does not give any warning that some of the files have not been copied at any stage. I am wondering if this a known problem with AFP and the Finder and/or if there is something that I can do to solve this problem.

  Read the article

• Setup of high-end web server and DB server cluster on Amazon EC2: Is this how it's done?

  - by user1086584

  Amazon is so technical, I want to confirm that my understanding is correct. We have a large 500 GB database. (OrientDB.) We will have it mirrored to one another in the same Availability Zone. We believe the database size will grow rapidly. The plan is: Get 4 large instances that are compatible types with Placement Groups (as well as ideally, Enhanced Networking) (2 for web, 2 for DB.) We use an EBS-backed instances to store our operating system. Discussion here: http://alestic.com/2012/01/ec2-ebs-boot-recommended We can set up ephemeral SSD instance storage as swap space. (But it is lost after even a reboot. I hear its hard to add ephemeral storage if booting from EBS, but possible.) For offsite backup, we will take periodic snapshots and store them on S3. Obviously we need to ensure the database is in a safe state when that snapshot happens to avoid corruption. (Any hints here, aside from shutting down the DB?) If the database gets too big, we need to create a EBS volume that's larger. We can use RAID to break the 1 TB limit: http://alestic.com/2009/06/ec2-ebs-raid Static assets on web servers will be stored on S3. Is that correct? Or am I missing something?

  Read the article

• Error with procmail script to use Maildir format

  - by bradlis7

  I have this code in /etc/procmailrc: DROPPRIVS=yes DEFAULT=$HOME/Maildir/ :0 * ? /usr/bin/test -d $DEFAULT || /bin/mkdir $DEFAULT { } :0 E { # Bail out if directory could not be created EXITCODE=127 HOST=bail.out } MAILDIR=$HOME/Maildir/ But, when the directory already exists, sometimes it will send a return email with this error: 554 5.3.0 unknown mailer error 127. The email still gets delivered, mind you, but it sends back an error code to the sending user as well. I fixed this temporarily by commenting out the EXITCODE and HOST lines, but I'd like to know if there is a better solution. I found this block of code in multiple places across the net, but couldn't really find why this error was coming back to me. It seems to happen when I send an email to a local user. Sometimes the user has a .forward file to send it on to other users, sometimes not, but the result has been the same. I also tried removing DROPPRIVS, just in case it was messing up the forwarding, but it did not seem to affect it. Is the line starting with * ? /usr/bin/test a problem? The * signifies a regex, but the ? makes it return an integer value, correct? What is the integer being matched against? Or is it just comparing the integer return value? Do I need a space between the two blocks? Thanks for the help.

  Read the article

• Why won't 2GB of ram across 3 of 4 slots work on my motherboard (max 2GB)?

  - by Andrew

  My desktop is an old home-built machine circa 200[5-6] running Ubuntu 11.10 (but this is not relevant because I'm reading available ram from BIOS loading screen), with an ASUS P5GPL motherboard, not X or X-SE - it has four slots. I'm mainly a laptop person, but keep this around for running a server from if needed, backing up to, seeding Ubuntu to people from, etc… It has four (DDR) ram slots, two black and two blue, in the order black-blue-black-blue (I will call them D, C, B, and A, respectively) with some space in the middle. The blue ones are the closest to the processor. I used to have two 512MB chips in the two blue slots. I just got a 1GB chip and plugged it into one of the black slots; my system didn't recognize it. I messed around and discovered that it will not recognize chips in many positions, and I couldn't get it to recognize all three of these chips at the same time. In particular, if I put the 512MB chips in A and B it would only use 1, but AC, AD, BD, and CD worked. I didn't try BC, I believe. Only some of these continue to work when I switch the 1GB chip into one of these positions. Can I have some advice as to how to position these chips to get all 2GB used? How about if I get another 1GB chip - where should I put the two? And what about the RAM maximum Crucial says? Can I go above 2GB, if I get another 1GB chip? Right now, I have a 512MB chip in A and the 1GB chip in C. EDIT: I read some other posts and tried dmidecode in Ubuntu to clarify the max memory question, that wasn't a major part anyways. It says my max memory module size is 1024M (OK) and my max memory size is 4096M (doesn't agree with Crucial OR the Asus web site, maybe it will only work while in Linux and BIOS won't OK it?).

  Read the article

• Conditionally changing MIME type in nginx

  - by Peter

  I'm using nginx as a frontend to Rails. All pages are cached as .html files on disk, and nginx serves these files if they exist. I want to send the correct MIME type for feeds (application/rss+xml), but the way I have so far is quite ugly, and I'm wondering if there is a cleaner way. Here is my config: location ~ /feed/$ { types {} default_type application/rss+xml; root /var/www/cache/; if (-f request_filename/index.html) { rewrite (.*) $1/index.html break; } if (-f request_filename.html) { rewrite (.*) $1.html break; } if (-f request_filename) { break; } if (!-f request_filename) { proxy_pass http://mongrel; break; } } location / { root /var/www/cache/; if (-f request_filename/index.html) { rewrite (.*) $1/index.html break; } if (-f request_filename.html) { rewrite (.*) $1.html break; } if (-f request_filename) { break; } if (!-f request_filename) { proxy_pass http://mongrel; break; } } My questions: Is there a better way to change the MIME type? All cached files have .html extensions and I cannot change this. Is there a way to factor out the if conditions in /feed/$ and /? I understand that I can use include, but I'm hoping for a better way. Putting part of the config in a different file is not that readable. Can you spot any bugs in the if conditions? I'm using nginx 0.6.32 (Debian Lenny). I prefer to use the version in APT. Thanks.

  Read the article

• PPTP server connection closes - Too much data?

  - by Sebastian Hoitz

  I set up a PPTP server for my company. However, every time I have another computer connected to this server (i.e. our backup server) and a lot of data gets transferred, the connection to this computer closes. In the syslog on the PPTP server I find this message: Apr 22 12:44:34 komola-chase pptpd[2581]: CTRL: Reaping child PPP[2583] Apr 22 12:44:34 komola-chase pppd[2583]: MPPE disabled Apr 22 12:44:34 komola-chase pppd[2583]: Connection terminated. Apr 22 12:44:34 komola-chase pppd[2583]: Exit. Apr 22 12:44:34 komola-chase pptpd[2581]: CTRL: Client 192.168.0.11 control connection finished Apr 22 12:55:11 komola-chase pptpd[2674]: GRE: xmit failed from decaps_hdlc: No buffer space available Apr 22 12:55:11 komola-chase pptpd[2674]: CTRL: PTY read or GRE write failed (pty,gre)=(6,7) Apr 22 12:55:11 komola-chase pppd[2675]: Modem hangup Apr 22 12:55:11 komola-chase pppd[2675]: Connect time 23.0 minutes. Hopefully you can help me as to what is wrong. As far as I can tell, there is no compression enabled on the PPTP server (npbsdcomp option). Thank you!

  Read the article

• Simple P2V help from Linux to Windows

  - by Ke

  Hi, I have two OS's installed on different drives in my PC. One linux (Centos 5.4) and one windows 7. Its getting tiresome to constantly have to stop and restart the PC when I want to use either OS. I would very much like to use Windows 7 as my host OS and access my linux OS from within Windows. However, im having trouble deciphering exactly how to do this (many of the articles seem confusing and a bit overkill) From what i have seen its possible to use VMWare converter to convert the physical linux image to a virtual image so that I can use it in windows. As im having problems understanding how this is done, I would really appreciate a step by step guide (for a newbie), or any simple tutorials that you can point me at. Some questions beforehand: 1) My linux image is around 80gb, do i need to take this into consideration? The linux drive is around 180gb in total. All my other drives are NTFS non writeable in linux (as I use them in windows and ntfs is dodgy in linux), so probably not possible to move the image over to my ntfs drives 2) Can I just zip the linux files up somehow and transfer it to windows to create the p2v? 3) Is it possible to do the P2V conversion while I am logged into windows. I can see the actual linux drive loaded in disk manager, but windows doesnt read linux file systems so im confused as to how to access the linux drive if this is possible. 4) Or will i need to do the whole p2v conversion inside linux? Cheers, any help is much appreciated Ke (a confused p2v newbie)

  Read the article

• On a failing hard drive, I am able to view data but unable to copy it - why?

  - by Tom

  I have a 2.5" external hard drive that is failing. It's not making the expected 'clicking' noise that most hard drives and I am able to view the data, but I am unable to actually retrieve the data. I attempted to use SpinRite in order to access the data on the drive, but it didn't like the external drive. When I view the drive's property page, the drive shows that it's used space is at 100% and that it has 0 bytes available; however, the progress indicator under the drive icon in Windows Explorer shows that it's roughly 50% full (which is correct). When I attempt to run Windows' "Error Checking" tool and attempt to "scan for an attempt recovery of bad sectors," the tool begins to run then immediately closes with no error message. I am able to browse the contents of the drive using Windows Explorer. When I begin to try copying any given single file, the copy process begins, an indicator starts, and then the copy fails with no real error message. The Disk Management page in Computer Management under Control Panel also shows this drive has being 'Healthy.' I dropped the drive off at a data recovery store and they said that "The data seems to be intact, but an internal failure is preventing any information from being retrieved." They offered to provide me references to a data recovery specialist. I've also attempted to run CHKDSK on the drive (with and without arguments) but it returns the following error: The type of the filesystem is RAW. CHKDSK is not available for RAW drives. Before going the route of more expensive data recovery, I'm wondering if these symptoms sound familiar to anyone? Other questions... I'm willing to continue trying tools such as TestDisk and/or PhotoRec (as the majority of the data that I'd like to salvage are photos) but how long I should expect either tool to run given approximately 400GB of data? I'm also comfortable using Linux so I welcome any suggestions for utilities or tools and strategies with which you've had success.

  Read the article

• See former key sequences in vim

  - by Vasiliy Sharapov

  Sometimes I share screen shots and clips of vim usage with others. It would be nice to expand on the part of the status bar highlighted in this picture: I would like some way to make previous key sequences visible as well, such as: y2w jj f[ p 2d - You can see the key sequences leading up to the current one. I'll elaborate on my wish list at the bottom. Is something like this is available as a plugin or vim script? The sheer number of scripts available on vim online makes this hard to find by keyword. Some features I would hope for (but seem improbable): Delimit key sequences with a non-keyboard character instead of space, and a different one for the current command, so y2w jj f[ p 2d might become y2w¦jj¦f[¦p » 2d Replace keys that have a letter alternative with the alternative, such as the right arrow key - ^[[C with the equivalent l. Edit: To clarify, the right arrow key is a valid key in vim, but has no character to represent it, the l key preforms the same function and could/should substitute it. Have previous keystrokes run all the way to the beginning of the line (instead of just one or two), and just have vim's command prompt overwrite it when necessary. Replace some keystrokes with a more elegant alternative, for example hhhhh with 5h or more impressively d2f) with d% (in the appropriate situation).

  Read the article

• I get a Segmentation fault when doing apt-get util-linux

  - by Adam

  I've found that a lot of upgrade commands and Apache on my system are failing with Segmentation faults. I don't know if this is the main one, but a lot of packages depend on util-linux: root@myUbuntuHardyHeronServer:~# apt-get install util-linux Reading package lists... Done Building dependency tree Reading state information... Done The following packages will be upgraded: util-linux 1 upgraded, 0 newly installed, 0 to remove and 72 not upgraded. 20 not fully installed or removed. Need to get 0B/441kB of archives. After this operation, 0B of additional disk space will be used. (Reading database ... 20547 files and directories currently installed.) Preparing to replace util-linux 2.13.1-5ubuntu2 (using .../util-linux_2.13.1-5ub untu3.1_i386.deb) ... Unpacking replacement util-linux ... Segmentation fault dpkg: warning - old post-removal script returned error exit status 139 dpkg - trying script from the new package instead ... Segmentation fault dpkg: error processing /var/cache/apt/archives/util-linux_2.13.1-5ubuntu3.1_i386 .deb (--unpack): subprocess new post-removal script returned error exit status 139 Segmentation fault dpkg: error while cleaning up: subprocess post-removal script returned error exit status 139 Errors were encountered while processing: /var/cache/apt/archives/util-linux_2.13.1-5ubuntu3.1_i386.deb E: Sub-process /usr/bin/dpkg returned an error code (1)

  Read the article

• Why would my HDD main partition suddenly become hidden?

  - by Luis Oscar

  A few days ago I was using my computer as usual and I turned it off. The next day it wouldn't boot up. It just stayed after the hardware diagnostic window on the intermittent underscore screen. So clearly It wasn't booting up. I tried turning it on and off a couple of times with no avail. Finally I used windows 7 disk and it seemed as if there was no HDD. not even the installation would see the HDD. So i thought it was dead, i bought a new one installed it with windows and used a external case with the old HDD. plug it in and still couldn't see it. I finally downloaded a partition program EASUS or something and my HDD was there listed WITHOUT a system letter. I could however explore it and i set it as Unhidden and it came back to life. I could see it normally. I really just wish someone could explain to me what happened here, was it a virus? does it means the HDD is about to die? How can i prevent this or what should I do now? should i stop using this OLD HDD? Thanks

  Read the article

• Intel Rapid Storage Technology (pre-OS) driver installation

  - by Nero theZero

  My desktop machine is built on Gigabyte GA-Z87-UD3H and Gigabyte provides the latest driver for Intel Rapid Storage Technology (IRST), which I installed after installing the OS. Same goes for my Lenovo Thinkpad-T420. And for both machine, checking the controller device under the IDE ATA/ATAPI Controllers section in Device Manager I see the driver has been updated to the latest version. I set the SATA controller to AHCI from BIOS On the desktop machine I have one WD 2TB BLACK & one WD 3TB Green I don’t use RAID, & no chance of using in near future, but according to Intel IRST improves performance in single disk scenario too. Now I have the following questions – What is the actual purpose of IRST (pre-OS install) driver that doesn’t get served with a post-OS driver that I installed? There must be some difference, otherwise there wouldn’t be a pre-OS version of the driver. Right? In the pre-OS procedure (loading the drivers at OS-installation time) after successfully completing the OS installation, do I need that post-OS driver? Because after installing from that one I got a quick launch icon that runs the IRST configuration application. Where do get that after installing the pre-OS driver? As it is “pre-OS”, when I load it at OS-installation time, does it updates anything at BIOS level or anywhere other than HDD? That’s because I’m going to dual boot Windows 7 with Windows 8.1, and after installing Windows 7 when I install Windows 8.1 & load the IRST driver for that, is there any chance of any “overwriting” or OS-incompatibility? In short, is there anything specific to follow while installing the second OS?

  Read the article

• New keyboard for linux: Adesso Tru-Form or MS Natural Keyboard 4000?

  - by Andrea

  Hi folks! I'm going to buy a new ergonomic keyboard for my laptop. In the following, keep in mind I live in Italy. I considered the following models: Adesso PCK-308UB - Adesso Tru-Form™ Pro - Contoured Ergonomic Keyboard with TouchPad-PS2 Pro: has a built-in touchpad in the same position of my laptop somewhat cheaper than the alternative below Cons: the surface doesn't seem to be bowl-shaped. keys seem to lay on a straight slightly-inclined surface. It seems an idea used extensively in other ergonomic keyboards according to a few comments on the net, new Adesso keyboards seem to lack robustness, they're likely to loose small parts after a few weeks or months. Other users, instead, seem to never had any problem in years and swear by their quality and comfortability. Those who had problems, however, lamented a lack of responsiveness from the manufacturer. I'm not sure whether the keyboard, at least the standard keys, and the touchpad will both be recognized correctly under linux distros (I mostly use FC btw) last time I checked, Adesso didn't have local resellers in my country Microsoft Natural Ergonomic Keyboard Pro: recognized as one of the most comfortable keyboards reliable customer service operating in my country AFAIK there are several documented ways to get extra buttons work with linux Cons: it doesn't have a builtin touchpad and has a numeric keypad wasting space to reach mouse But there could be other keyboards I haven't considered yet, so here follows my ideal keyboard wishlist, ordered by priority linux compatible basic ergonomic design, which entails split tilted keyboard and pads advanced ergonomic design, like true-ergonomic's or kinesis , where special keys (like enter, caps-lock...) are placed symmetrically in the middle to be used by thumbs a builtin touchpad/trackball placed under the keyboard. I just love this on my notebook. I think it's pretty effective, since it allows my hand to rest naturally everytime I use it. Any opinion on this? high-quality switches, like cherry's (unsure about this one) additional programmable keys placed near usual ones, to simplify typing shortcuts TIA Andrea

  Read the article

• Spotlight can't see anything in Applications

  - by mix

  There have been other threads on this but none of the solutions mentioned have helped me. Spotlight has stopped showing any results for my Applications. I've tried reindexing and removing the index so it rebuilds it. No change. I've tried adding Applications to the Privacy tab and removing it, no change. I tried repairing disk permissions and redoing the above, no change. I've tried removing everything from the index except Applications and then I just get nothing for any search at all (except dictionary entries). I tried adding a symlink in my homedir to Applications and reindexing, but no change. Any ideas on what to do? I'm running Snow Leopard. This is driving me crazy! Update: I've noticed that when I start a reindex with sudo mdutil -E / and then immediately do a spotlight search for an app that the app shows up temporarily until spotlight gets disabled due to active indexing. After the indexing is done the app entries go away.

  Read the article

• mac terminal run a file of commands

  - by Ilan Tal

  I am coming from Linux and trying to get a Mac to do what I want it to do. The question is what is the best tool to use. I want to mount (unmount) several remote disks. If I go into a terminal I can do the trick by mount -t smbfs //username:pass@addr /Users/me/RemoteDisks/mnt1 Since I want to mount several disks I would like to put all of the information into a file, store it in Documents/subfolder and make a link to it on the desktop (or somewhere better, if there is a better place). At the moment I have manually run the appropriate command in the terminal and the remote disk is mounted and I see its contents. What I need is a one click method to run a file to mount all the disks. I tried Apple script but that didn't like my commands. I don't know exactly what it is expecting to see and perhaps Apple script is the wrong tool. I have no problems in Linux, but the Mac is new to me and I don't know what I should be using. Thanks, Ilan

  Read the article

• RHEL 5.3 Kickstart - How specify location of individual package in Workstation folder?

  - by Ed

  I keep getting "package does not exist" errors during the install. I made a kickstart ISO to create an unattended install of a RHEL 5.3 build machine for C++ software releases. It pulls the kickstart config file from our internal web server. This is handy; it makes it easy to test and modify without having to make a new ISO. And I plan to check it in to version control if I can get it working. Anyway, the rpm packages are located in two folders on the disk; Client and Workstation. The packages install fine for the ones that are physically located under the Client folder. It cannot find those under the Workstation folder such as as doxygen and subversion complaining that packages do not exist. Is there a way to specify the individual package location? # ----------------------------------------------------------------------------- # P A C K A G E S # ----------------------------------------------------------------------------- %packages @gnome-desktop @core @base @base-x @printing @development-tools emacs kexec-tools fipscheck xorg-x11-server-Xnest xorg-x11-server-Xvfb #Packages Located in Workstation Folder *** Install can not find any of these ?? bison doxygen gcc-c++ subversion zlib-devel freetype-devel libxml2-devel Thanks in advance, -Ed

  Read the article

• Ubuntu 10.04 - Add RAID 1 Array?

  - by N Rahl

  I have an existing Ubuntu 10.04 desktop system setup and running on a hard drive (Drive A). I'd like to add 2 more hard drives (Drives B & C, same size) to the system and mount them as a RAID 1 array. How do I do that? I know how to create RAID arrays during the installation, but I don't want to reinstall my system, and I shouldn't have to since my system files will stay on their own drive separate from the RAID array. I've physically added both drives to the system, and formatted them as EXT3 with gparted. Ubuntu's disk utility has a "create raid" option, but it won't let me select any of my drives (it thinks they're all full). I don't mind using mdadm, but I've found several guides that are old, and give conflicting advice. Some say I have to edit an /etc/raidtab file, some say this is done automatically. So what's the current (Ubuntu 10.04) preferred way of adding a RAID 1 to an existing system? It should turn into a raid at boot, and mount itself in /home/myname/files/. Thanks!

  Read the article

• What do different patterns mean in Windows 8 file copy dialog

  - by MainMa

  When copying or extracting files, Windows 8 shows the chart with the speed of the operation. I noticed several patterns: Randomness, High speed at the beginning, then low speed during the most part of the operation, Mostly constant speed. 1. Randomness/nice mountains. 2. High speed at the beginning, then low speed during the most part of the operation. 3. Low speed at the beginning, then high speed during the most part of the operation. (Similar to the previous image, but inverted) 3. Mostly constant speed. (Same as previous image, but without the fast start) I'm curious, what each of those patterns mean? Do some indicate that there may be a problem with hard disk performance? Why the nearly constant speed is so rare, even when copying a single large file from and to a spinning drive, or when copying a single large file or a bunch of small files from and to an SSD?

  Read the article

• Change which server mailbox is associated with in Exchange 2007

  - by tacos_tacos_tacos

  I have restored and mounted an EDB file onto a new Exchange 2007 Server. However, the old server is still online and although all the mailboxes I need are in the newly-mounted database, in Exchange 2007 System Manager it still shows that the mailbox is associated with the old server. If I try to "Move" the database it actually tries to copy the files from the old server to the new server, which is not necessary because they are already there - and produces and error about the mailbox on the destination already existing. How can I simply tell Exchange (AD?) to use the new server to find the mailbox rather than the old? Edit: I did the restore by taking the old server offline (turning off all Exchange services), copying EDB file to the new server, restoring it with eseutil, and mounting it to the new server. I did it this way in part because I didn't know a better way and in part because I couldn't use move-mailbox as the source location had a horrible Internet connection (which is why Exchange is being moved to the new location). I had to copy the EDB from the old server to a hard disk, go somewhere with a better Internet connection, upload the EDB to the new server.

  Read the article

• SQL Server Installaion error 0x84B40000

  - by Kurtevich

  I have a problem installing SQL Server 2008 R2. Long time ago I had it installed, and then uninstalled. It was left in "Add/remove programs", but I didn't pay attention on that. I had 2005 installed. And now there is a need to install 2008. I removed 2005 and started installing 2008, but it says that space on C: is not enough. That's when I found out that "Add/remove programs" shows it occupying more than 4 gigabytes, though I used to uninstall it. So I click "Remove", it shows all those many screens and validations, shows that removal completed, but the size of Program Files folder is still more than 4 GB. I removed (from "Add\remove programs" everything that had "SQL Server" in it's name, but that main "SQL Server 2008" item is still there and still 4 GB and uninstalling does nothing. Because installation of SQL Server did not show existing instances, and I don't see any running services related to SQL server (well, almost any, more details in the end), I though that this folder contains just some leftover staff and data and deleted it manually. Then agreed to removing of the item in "Add/remove programs" and everything looks clean. Now every time I try to install SQL Server (even in the minimum configuration), I receive the following error: SQL Server Setup has encountered the following error: The specified credentials that were provided for the SQL Server service are not valid. To continue, provide a valid account and password for the SQL Server service. Error code 0x84B40000. What is this service mentioned here? This error looks like I'm trying to add features to existing server and it can't login. But the setup didn't ask me for any credentials, except one username that couldn't be changed. Here are the services shown that can be related, both disabled and pointing to non-existing executables: SQL Active Directory Helper Service SQL Full-text Filter Daemon Launcher (MSSQLSERVER) I understand that this must be because of my manual deletion, but is there a way to clean it up now?

  Read the article

• Macbook Pro Triple Boot OS X Lion, Windows 7 and Windows 8

  - by Lloyd Sparkes

  MacBook Pro (Summer 2010 Model, Basic Model) I currently have OS X Lion and Windows 7 running side by side on my MacBook Pro. However I have a need to get Windows 8 running as well in this mix (a Virtual Machine is not good enough, I need the performance). I have created a suitably sized parition (80GB) that is recognizable in Boot Camp. However every time I try to boot from the USB stick (that worked to install Windows 8 on my PC) using the latest version of rEFIt, it just boots Windows 7 and not the Windows 8 installer. I cannot start the installation within Windows 7 as it will just install over Windows 7. I'm guessing the Boot Camp emulation is doing something werid to stop the "Press any key to install Windows..." message from appearing (which should happen if the installer detects Windows is already installed (e.g. if you left your install disk in). Is there a way to get around this / force the installer to start? (Note I cannot start the Windows 7 installer either if I wanted to install a second copy of Windows 7 to upgrade to Windows 8)

  Read the article

• Can't pop3 from exchange server after a reboot

  - by BLAKE

  Last night I shutdown my Exchange 2003 Virtual Machine, I added a new VHD (For backups), and booted it again. Now I can't POP3 email from it with Outlook 2007. In Outlook I get the error: Task '[email protected] - Receiving' reported error (0x800CCC0F) : 'The connection to the server was interrupted. If this problem continues, contact your server administrator or Internet service provider (ISP).' Does anybody know what is wrong? All I did was a reboot. I haven't formated the added disk. There are no weird errors in the event log. I can still send mail with Outlook over port 25. I can send and recieve mail with OWA. I can POP3 the mail to my phone (it take about 15 minutes after sending a message, but I do get it eventually). EDIT: The 'Microsoft Exchange POP3' Service says that it is started but if I stop it and try to start it again, it fails saying 'Could not start the Microsoft Exchange POP3 service on Local Computer. Error 1053: The service did not respond to the start or control request in a timely fashion.' I did some googling and someone on exchangefreaks.com said that if I use task manager to 'End Task' on inetinfo.exe, then I can start the POP3 service fine. Does anyone know what causes this problem? I am fine for now since I did get the Service started, but If it does this after every reboot...

  Read the article

• Xen guests accessing LUNs

  - by mechcow

  We are using RHEL5.3 with a Clarion SAN attached by FC. Our situation is that we have a number of LUNs presented to Hosts and we want to dynamically present the LUNs to Xen Guests. We are not sure on what the best practice approach is to set this up. The Xen guests will form a cluster together and need the LUNs only for data partitions, i.e. when they are actively running services. So one approach would be to always present all disks to all Xen guests, and then rely up on the cluster software, and mount itself, to not mount the disk twice in two locations. This sounds kinda risky and also is not very secure (one cracked guest can see/destroy all the data). Another approach would be to dynamically add and remove the disks from the Xen guests at the dom0 level (using xm block-attach). This could work but sounds slightly complicated, I'm wondering whether Red Hat Cluster Suite supports this in some way or whether there are scripts to do this. Yet another approach would be to have the LUNs endpointed at the Xen guests themselves - I'm not sure whether this is technically possible since the multipathing has to be done at the Host level.

  Read the article

• How can I restore my original IME Romaji input settings?

  - by JOhn K

  the this one, Japanese IME on Windows: switch back to romaji input method (3) did not help. The problem seems the same. My Vista home premium version PC, I had been using Microsoft IME to use English and Japanese input using romaji henkan for a long time. One day, all of a sudden, first when I started up the PC, it has cap lock indicator ON. So, I press SHIFT key, CAP lock indicator is off!(This I have to do every morning.) Now when I want to type romaji input to change to Japanese, I switch EN English (United States) to "JP Japanese (Japan) and select input to hiragana input. It worked until that day. But now when I set to input romaji for hiragana as I used to do and start typing, then it shows Japanese hiragana directly on the display just as keyboard setting as Japanese ???109???????? as shown in Wikipedia JIS keyboard. And I cannot show hiragana as I wanted ( I can convert to Kanji OK) etc. by hitting space key. But its key board arrangement is what I never learned. Other thing I found is when I hit "`" key, it switches between hiragana and alphabet. When I see Control panel setting it is the same setting as I have seen. Please suggest me a solution to get the original setting for IME input mode as I used to do. John K.

  Read the article

< Previous Page | 520 521 522 523 524 525 526 527 528 529 530 531  | Next Page >