Search Results

Search found 14757 results on 591 pages for 'switch statement'.

Page 527/591 | < Previous Page | 523 524 525 526 527 528 529 530 531 532 533 534  | Next Page >

• pfSense 2.1 OpenVPN client not using tunnelled interface

  - by Brian M. Hunt

  I'm having some trouble getting OpenVPN working on my pfSense box. The issue is quite strange to me. When I have the OpenVPN turned on, only my router is able to connect to the Internet. From the router I can use ping, links, etc., and connections work exactly as expected - through the VPN, with the IP address assigned by my VPN provider (Proxy.sh, incidentally). However, none of the clients on the local network can connect to the Internet. I get timeouts when using ping or a web browser. I can ping my router, and the IP address of the gateway. When I switch the default gateway from the VPN to my ISP's gateway, all works exactly as expected. Here the routing table (netstat -r) when in VPN mode, and a key for it: IPv4 Destination Gateway Flags Refs Use Mtu Netif Expire 0.0.0.0/1 10.XX.X.53 UGS 0 122 1500 ovpnc1 = default 10.XX.X.53 UGS 0 235 1500 ovpnc1 8.8.8.8 10.XX.X.53 UGHS 0 82 1500 ovpnc1 10.XX.X.1/32 10.11.0.53 UGS 0 0 1500 ovpnc1 10.XX.X.53 link#12 UH 0 0 1500 ovpnc1 10.XX.X.54 link#12 UHS 0 0 16384 lo0 ZZ.XX.XXX.0/20 link#1 U 0 83 1500 re0 ZZ.XX.XXX.XXX link#1 UHS 0 0 16384 lo0 127.0.0.1 link#9 UH 0 12 16384 lo0 128.0.0.0/1 10.11.0.53 UGS 0 123 1500 ovpnc1 192.168.1.0/24 link#11 U 0 1434 1500 ue0 192.168.1.1 link#11 UHS 0 0 16384 lo0 YYY.YYY.YYY.YYY/32 ZZ.XX.XXX.1 UGS 0 249 1500 re0 IP addresses 10.XX.X.53/54 - My DHCP-assigned IP address/pair from the VPN provider ZZ.XX.XXX.XXX - My external IP assigned by my ISP YYY.YYY.YYY.YYY - The external IP assigned by the VPN provider Interfaces ovpnc1 - My VPN client interface re0 - My LAN interface ue0 - My WAN interface This looks essentially what I would expect it to be. The default route is through the VPN provider. The VPN address is routed through the ISP-assigned IP address. I am not sure what would be wrong here. So figuring this was a firewall issue, I basically tried enabling all in/out traffic. This did not seem to remedy the problem. Also figuring it could possibly be some client networking issue, I restarted the clients on the LAN. This did not help. I also ran route flush and reset the routes manually. So I am a bit stumped, and would be very grateful for any thoughts on what the problem might be.

  Read the article

• Can an administration extraction of an MSI file perform registry and/or system wide changes?

  - by Wil

  I am always getting MSI (or setup EXEs which are basically MSI) files, and half the time they really do not need to be a setup. Microsoft is probably one of the biggest sources - almost every time I want to download a little source code sample, it has a MSI which if you install, only usually has three files. I would rather not do an install and add it to the add/remove programs and who knows what else (although I am sure it wouldn't be that bad) for the sake of three files! For this reason, I always use the following command: MSIEXEC /a <filename.msi> /qb TARGETDIR=<directory name> Now, this works fine and I have never had problems... However, I was just browsing some articles on Technet and found the following resource about administration installs. Apparently, MSI files can have two sequences: The AdminUISequence Table and the AdminExecuteSequence Table. I am not so worried about the AdminUISequence Table as it states that "The installer skips the actions in this table if the user interface level is set to basic UI or no UI", and this is what the /qb switch I use does. However, there is nothing similar written against AdminExecuteSequence Table. I realise that many people who write MSI files simply do it for a single end user and probably do not even touch the admin install options, however, is it possible for them to set items that can affect the system and if so, is there a fail proof way of extracting? I do already use 7-zip, however despite it being on the "supported" page, MSI support is lacking... well... completely sucks. It looses the file names and is generally useless. They have a bug which was closed with no reason/resolution over three years ago, and I opened a forum post and haven't had a reply. I would not really want to install any additional programs if I could help it and just want peoples opinions on this. Thanks. edit - Should also say, I run with UAC on, and I have never ever had a elevation prompt whilst performing the MSIEXEC operation, so I am guessing I have never had a system wide change, however, I am still curious as to if it is possible... As if changes (even just to the user) are possible I would do this locally/in a VM and never on a server or place of importance!

  Read the article

• MySQL: Pacemaker cannot start the failed master as a new slave?

  - by quanta

  I'm going to setup failover for MySQL replication (1 master and 1 slave) follow this guide: https://github.com/jayjanssen/Percona-Pacemaker-Resource-Agents/blob/master/doc/PRM-setup-guide.rst Here're the output of crm configure show: node serving-6192 \ attributes p_mysql_mysql_master_IP="192.168.6.192" node svr184R-638.localdomain \ attributes p_mysql_mysql_master_IP="192.168.6.38" primitive p_mysql ocf:percona:mysql \ params config="/etc/my.cnf" pid="/var/run/mysqld/mysqld.pid" socket="/var/lib/mysql/mysql.sock" replication_user="repl" replication_passwd="x" test_user="test_user" test_passwd="x" \ op monitor interval="5s" role="Master" OCF_CHECK_LEVEL="1" \ op monitor interval="2s" role="Slave" timeout="30s" OCF_CHECK_LEVEL="1" \ op start interval="0" timeout="120s" \ op stop interval="0" timeout="120s" primitive writer_vip ocf:heartbeat:IPaddr2 \ params ip="192.168.6.8" cidr_netmask="32" \ op monitor interval="10s" \ meta is-managed="true" ms ms_MySQL p_mysql \ meta master-max="1" master-node-max="1" clone-max="2" clone-node-max="1" notify="true" globally-unique="false" target-role="Master" is-managed="true" colocation writer_vip_on_master inf: writer_vip ms_MySQL:Master order ms_MySQL_promote_before_vip inf: ms_MySQL:promote writer_vip:start property $id="cib-bootstrap-options" \ dc-version="1.0.12-unknown" \ cluster-infrastructure="openais" \ expected-quorum-votes="2" \ no-quorum-policy="ignore" \ stonith-enabled="false" \ last-lrm-refresh="1341801689" property $id="mysql_replication" \ p_mysql_REPL_INFO="192.168.6.192|mysql-bin.000006|338" crm_mon: Last updated: Mon Jul 9 10:30:01 2012 Stack: openais Current DC: serving-6192 - partition with quorum Version: 1.0.12-unknown 2 Nodes configured, 2 expected votes 2 Resources configured. ============ Online: [ serving-6192 svr184R-638.localdomain ] Master/Slave Set: ms_MySQL Masters: [ serving-6192 ] Slaves: [ svr184R-638.localdomain ] writer_vip (ocf::heartbeat:IPaddr2): Started serving-6192 Editing /etc/my.cnf on the serving-6192 of wrong syntax to test failover and it's working fine: svr184R-638.localdomain being promoted to become the master writer_vip switch to svr184R-638.localdomain Current state: Last updated: Mon Jul 9 10:35:57 2012 Stack: openais Current DC: serving-6192 - partition with quorum Version: 1.0.12-unknown 2 Nodes configured, 2 expected votes 2 Resources configured. ============ Online: [ serving-6192 svr184R-638.localdomain ] Master/Slave Set: ms_MySQL Masters: [ svr184R-638.localdomain ] Stopped: [ p_mysql:0 ] writer_vip (ocf::heartbeat:IPaddr2): Started svr184R-638.localdomain Failed actions: p_mysql:0_monitor_5000 (node=serving-6192, call=15, rc=7, status=complete): not running p_mysql:0_demote_0 (node=serving-6192, call=22, rc=7, status=complete): not running p_mysql:0_start_0 (node=serving-6192, call=26, rc=-2, status=Timed Out): unknown exec error Remove the wrong syntax from /etc/my.cnf on serving-6192, and restart corosync, what I would like to see is serving-6192 was started as a new slave but it doesn't: Failed actions: p_mysql:0_start_0 (node=serving-6192, call=4, rc=1, status=complete): unknown error Here're snippet of the logs which I'm suspecting: Jul 09 10:46:32 serving-6192 lrmd: [7321]: info: rsc:p_mysql:0:4: start Jul 09 10:46:32 serving-6192 lrmd: [7321]: info: RA output: (p_mysql:0:start:stderr) Error performing operation: The object/attribute does not exist Jul 09 10:46:32 serving-6192 crm_attribute: [7420]: info: Invoked: /usr/sbin/crm_attribute -N serving-6192 -l reboot --name readable -v 0 The full logs: http://fpaste.org/AyOZ/ The strange thing is I can starting it manually: export OCF_ROOT=/usr/lib/ocf export OCF_RESKEY_config="/etc/my.cnf" export OCF_RESKEY_pid="/var/run/mysqld/mysqld.pid" export OCF_RESKEY_socket="/var/lib/mysql/mysql.sock" export OCF_RESKEY_replication_user="repl" export OCF_RESKEY_replication_passwd="x" export OCF_RESKEY_test_user="test_user" export OCF_RESKEY_test_passwd="x" sh -x /usr/lib/ocf/resource.d/percona/mysql start: http://fpaste.org/RVGh/ Did I make something wrong?

  Read the article

• Detach current session and attach to another session, done with one script, can I?

  - by Jimm Chen

  After reading the vague official doc of GNU screen( http://www.gnu.org/software/screen/manual/screen.html ) and asking quite some questions at this site. I still cannot figure out how to accomplish such a task with a shell script. This task costs some words to describe. Assume I'm using PuTTY to telnet into my Linux server. ?STEP 1? Launch 2 telnet connections . From putty window 1 (PTWIN1),telnet into Linux Bash shell, execute screen -RR to launch a screen session, and get session name 21385.pts-4.linux-ic37 . From putty window 2 (PTWIN2), do that same as in PTWIN1, but this time, I get session name 22041.pts-9.linux-ic37 . Now, we have two screen sessions running simultaneously. We can check this: $ screen -ls There are screens on: 22041.pts-9.linux-ic37 (Attached) 21385.pts-4.linux-ic37 (Attached) 2 Sockets in /var/run/uscreens/S-chj2. ?STEP 2? Assume that for some reason, PTWIN1's TCP connection is lost abnormally(but server doesn't know that), and an urgent work is pending on session 21385 and I want to quickly regain control of it. Fortunately, we know the 21385 session is still there, so, I want to have PTWIN2 attach to session 21385. Because I hate to remember the esoteric screen option all the time, so I decide to write a script called sttach. I hope that sttach 21385.pts-4.linux-ic37 can let me attach to session 21385(for PTWIN2). Now, let's say sttach works well and I take control of 21385 on PTWIN2. ?STEP 3? Some minutes later. I want to go back to work on session 22041. Here, please allow me to have PTWIN2 remain associated with session 21385. What I would like to do is to launch another putty window (PTWIN3), telnet into server, and execute sttach 22041.pts-9.linux-ic37 in hope that I can resume session 22041 on PTWIN3 . You can see the benefit of sttach: as long as I know the target session name, I can call it to have my PuTTY window switch to that session, regardless whether the target session is "(Attached)" or "(Detached)", and regardless whether the running context is inside a screen session or not. Now the question: How to write the (Bash) script sttach? I mean, run screen with appropriate options in sttach to accomplish the goal. Waiting for your kind answer. Thank you. My previous questions regarding GNU screen: GNU screen, how to get current sessionname programmatically Is it possible to change GNU screen session name after created? How do I know I'm running inside a linux "screen" or not? My env: openSUSE Linux 11.3, GNU screen 4.00.03 (FAU) 23-Oct-06

  Read the article

• Garbled text in Screen [closed]

  - by Prabin Dahal

  The graphical Interface in my system is garbled with some text. At the beginning I thought it was due to java and tomcat that I installed. But after removing java and tomcat, it is still the same. I am using ubuntu server and i have installed xfce desktop environment with oboard softkey I have added my dmesg output to this message. What is the problem here. I am not able to figure it out. Thank you for your help. Prabin [ 0.390936] usbcore: registered new interface driver usbfs [ 0.391006] usbcore: registered new interface driver hub [ 0.391147] usbcore: registered new device driver usb [ 0.391580] PCI: Using ACPI for IRQ routing [ 0.400509] PCI: pci_cache_line_size set to 64 bytes [ 0.400669] reserve RAM buffer: 000000000009ec00 - 000000000009ffff [ 0.400681] reserve RAM buffer: 000000007f597000 - 000000007fffffff [ 0.400699] reserve RAM buffer: 000000007f6f0000 - 000000007fffffff [ 0.401135] NetLabel: Initializing [ 0.401155] NetLabel: domain hash size = 128 [ 0.401168] NetLabel: protocols = UNLABELED CIPSOv4 [ 0.401212] NetLabel: unlabeled traffic allowed by default [ 0.401466] HPET: 3 timers in total, 0 timers will be used for per-cpu timer [ 0.401494] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0 [ 0.401520] hpet0: 3 comparators, 64-bit 14.318180 MHz counter [ 0.408228] Switching to clocksource hpet [ 0.434341] AppArmor: AppArmor Filesystem Enabled [ 0.434447] pnp: PnP ACPI init [ 0.434531] ACPI: bus type pnp registered [ 0.434784] pnp 00:00: [bus 00-ff] [ 0.434794] pnp 00:00: [io 0x0cf8-0x0cff] [ 0.434804] pnp 00:00: [io 0x0000-0x0cf7 window] [ 0.434813] pnp 00:00: [io 0x0d00-0xffff window] [ 0.434822] pnp 00:00: [mem 0x000a0000-0x000bffff window] [ 0.434831] pnp 00:00: [mem 0x00000000 window] [ 0.434840] pnp 00:00: [mem 0x80000000-0xffffffff window] [ 0.435018] pnp 00:00: Plug and Play ACPI device, IDs PNP0a08 PNP0a03 (active) [ 0.435526] pnp 00:01: [mem 0xe0000000-0xefffffff] [ 0.435537] pnp 00:01: [mem 0x7f700000-0x7f7fffff] [ 0.435545] pnp 00:01: [mem 0x7f800000-0x7fffffff] [ 0.435554] pnp 00:01: [mem 0xfee00000-0xfeefffff] [ 0.435727] system 00:01: [mem 0xe0000000-0xefffffff] has been reserved [ 0.435754] system 00:01: [mem 0x7f700000-0x7f7fffff] has been reserved [ 0.435775] system 00:01: [mem 0x7f800000-0x7fffffff] has been reserved [ 0.435796] system 00:01: [mem 0xfee00000-0xfeefffff] has been reserved [ 0.435818] system 00:01: Plug and Play ACPI device, IDs PNP0c01 (active) [ 0.436233] pnp 00:02: [io 0x0000-0xffffffffffffffff disabled] [ 0.436245] pnp 00:02: [io 0x0000-0xffffffffffffffff disabled] [ 0.436414] system 00:02: Plug and Play ACPI device, IDs PNP0c02 (active) [ 0.436512] pnp 00:03: [io 0x0060] [ 0.436521] pnp 00:03: [io 0x0064] [ 0.436548] pnp 00:03: [irq 1] [ 0.436682] pnp 00:03: Plug and Play ACPI device, IDs PNP0303 PNP030b (active) [ 0.436825] pnp 00:04: [irq 12] [ 0.436958] pnp 00:04: Plug and Play ACPI device, IDs PNP0f03 PNP0f13 (active) [ 0.437835] pnp 00:05: [io 0x03f8-0x03ff] [ 0.437861] pnp 00:05: [irq 4] [ 0.437870] pnp 00:05: [dma 0 disabled] [ 0.438142] pnp 00:05: Plug and Play ACPI device, IDs PNP0501 (active) [ 0.439014] pnp 00:06: [io 0x02f8-0x02ff] [ 0.439036] pnp 00:06: [irq 3] [ 0.439045] pnp 00:06: [dma 0 disabled] [ 0.439297] pnp 00:06: Plug and Play ACPI device, IDs PNP0501 (active) [ 0.439346] pnp 00:07: [io 0x0000-0x000f] [ 0.439355] pnp 00:07: [io 0x0081-0x0083] [ 0.439363] pnp 00:07: [io 0x0087] [ 0.439371] pnp 00:07: [io 0x0089-0x008b] [ 0.439380] pnp 00:07: [io 0x008f] [ 0.439388] pnp 00:07: [io 0x00c0-0x00df] [ 0.439563] system 00:07: Plug and Play ACPI device, IDs PNP0c01 (active) [ 0.439617] pnp 00:08: [io 0x0070-0x0077] [ 0.439639] pnp 00:08: [irq 8] [ 0.439751] pnp 00:08: Plug and Play ACPI device, IDs PNP0b00 (active) [ 0.439788] pnp 00:09: [io 0x0061] [ 0.439893] pnp 00:09: Plug and Play ACPI device, IDs PNP0800 (active) [ 0.439977] pnp 00:0a: [io 0x0010-0x001f] [ 0.439986] pnp 00:0a: [io 0x0022-0x003f] [ 0.439994] pnp 00:0a: [io 0x0044-0x005f] [ 0.440055] pnp 00:0a: [io 0x0063] [ 0.440063] pnp 00:0a: [io 0x0065] [ 0.440071] pnp 00:0a: [io 0x0067-0x006f] [ 0.440079] pnp 00:0a: [io 0x0072-0x007f] [ 0.440086] pnp 00:0a: [io 0x0080] [ 0.440094] pnp 00:0a: [io 0x0084-0x0086] [ 0.440102] pnp 00:0a: [io 0x0088] [ 0.440109] pnp 00:0a: [io 0x008c-0x008e] [ 0.440117] pnp 00:0a: [io 0x0090-0x009f] [ 0.440125] pnp 00:0a: [io 0x00a2-0x00bf] [ 0.440133] pnp 00:0a: [io 0x00e0-0x00ef] [ 0.440141] pnp 00:0a: [io 0x04d0-0x04d1] [ 0.440150] pnp 00:0a: [io 0x0000-0xffffffffffffffff disabled] [ 0.440160] pnp 00:0a: [io 0x0000-0xffffffffffffffff disabled] [ 0.440168] pnp 00:0a: [io 0x03f4] [ 0.440175] pnp 00:0a: [io 0x03f5] [ 0.440183] pnp 00:0a: [io 0x0374] [ 0.440190] pnp 00:0a: [io 0x0375] [ 0.440405] system 00:0a: [io 0x04d0-0x04d1] has been reserved [ 0.440432] system 00:0a: [io 0x03f4] has been reserved [ 0.440451] system 00:0a: [io 0x03f5] has been reserved [ 0.440469] system 00:0a: [io 0x0374] has been reserved [ 0.440488] system 00:0a: [io 0x0375] has been reserved [ 0.440508] system 00:0a: Plug and Play ACPI device, IDs PNP0c02 (active) [ 0.440550] pnp 00:0b: [io 0x00f0-0x00ff] [ 0.440572] pnp 00:0b: [irq 13] [ 0.440691] pnp 00:0b: Plug and Play ACPI device, IDs PNP0c04 (active) [ 0.440770] pnp 00:0c: [io 0x0810] [ 0.440779] pnp 00:0c: [io 0x0800-0x080f] [ 0.440787] pnp 00:0c: [io 0xffff] [ 0.440947] system 00:0c: [io 0x0810] has been reserved [ 0.440970] system 00:0c: [io 0x0800-0x080f] has been reserved [ 0.440989] system 00:0c: [io 0xffff] has been reserved [ 0.441010] system 00:0c: Plug and Play ACPI device, IDs PNP0c02 (active) [ 0.441620] pnp 00:0d: [io 0x0900-0x097f] [ 0.441630] pnp 00:0d: [io 0x09c0-0x09ff] [ 0.441639] pnp 00:0d: [io 0x0400-0x043f] [ 0.441647] pnp 00:0d: [io 0x0480-0x04bf] [ 0.441656] pnp 00:0d: [mem 0xfec00000-0xfec85fff] [ 0.441664] pnp 00:0d: [mem 0xfed1c000-0xfed1ffff] [ 0.441673] pnp 00:0d: [mem 0x000c0000-0x000dffff] [ 0.441689] pnp 00:0d: [mem 0x000e0000-0x000effff] [ 0.441697] pnp 00:0d: [mem 0x000f0000-0x000fffff] [ 0.441706] pnp 00:0d: [mem 0xff800000-0xffffffff] [ 0.441911] system 00:0d: [io 0x0900-0x097f] has been reserved [ 0.441935] system 00:0d: [io 0x09c0-0x09ff] has been reserved [ 0.441955] system 00:0d: [io 0x0400-0x043f] has been reserved [ 0.441975] system 00:0d: [io 0x0480-0x04bf] has been reserved [ 0.441997] system 00:0d: [mem 0xfec00000-0xfec85fff] could not be reserved [ 0.442019] system 00:0d: [mem 0xfed1c000-0xfed1ffff] has been reserved [ 0.442040] system 00:0d: [mem 0x000c0000-0x000dffff] could not be reserved [ 0.442061] system 00:0d: [mem 0x000e0000-0x000effff] could not be reserved [ 0.442082] system 00:0d: [mem 0x000f0000-0x000fffff] could not be reserved [ 0.442103] system 00:0d: [mem 0xff800000-0xffffffff] has been reserved [ 0.442126] system 00:0d: Plug and Play ACPI device, IDs PNP0c01 (active) [ 0.442308] pnp 00:0e: [mem 0xfed00000-0xfed003ff] [ 0.442454] pnp 00:0e: Plug and Play ACPI device, IDs PNP0103 (active) [ 0.442569] pnp 00:0f: [mem 0x7f6f0000-0x7f6fffff] [ 0.442762] system 00:0f: [mem 0x7f6f0000-0x7f6fffff] has been reserved [ 0.442788] system 00:0f: Plug and Play ACPI device, IDs PNP0c01 (active) [ 0.443360] pnp: PnP ACPI: found 16 devices [ 0.443378] ACPI: ACPI bus type pnp unregistered [ 0.443395] PnPBIOS: Disabled by ACPI PNP [ 0.486106] PCI: max bus depth: 3 pci_try_num: 4 [ 0.486189] pci 0000:00:1c.0: PCI bridge to [bus 01-01] [ 0.486217] pci 0000:00:1c.0: bridge window [io 0xe000-0xefff] [ 0.486241] pci 0000:00:1c.0: bridge window [mem 0xd0100000-0xd01fffff] [ 0.486266] pci 0000:00:1c.0: bridge window [mem 0xff700000-0xff7fffff pref] [ 0.486298] pci 0000:03:01.0: PCI bridge to [bus 04-04] [ 0.486319] pci 0000:03:01.0: bridge window [io 0xd000-0xdfff] [ 0.486348] pci 0000:03:01.0: bridge window [mem 0xd0000000-0xd00fffff] [ 0.486374] pci 0000:03:01.0: bridge window [mem 0xff600000-0xff6fffff 64bit pref] [ 0.486406] pci 0000:03:02.0: PCI bridge to [bus 05-05] [ 0.486444] pci 0000:03:03.0: PCI bridge to [bus 06-06] [ 0.486479] pci 0000:02:00.0: PCI bridge to [bus 03-06] [ 0.486499] pci 0000:02:00.0: bridge window [io 0xd000-0xdfff] [ 0.486522] pci 0000:02:00.0: bridge window [mem 0xd0000000-0xd00fffff] [ 0.486545] pci 0000:02:00.0: bridge window [mem 0xff600000-0xff6fffff 64bit pref] [ 0.486575] pci 0000:00:1c.1: PCI bridge to [bus 02-06] [ 0.486593] pci 0000:00:1c.1: bridge window [io 0xd000-0xdfff] [ 0.486615] pci 0000:00:1c.1: bridge window [mem 0xd0000000-0xd00fffff] [ 0.486637] pci 0000:00:1c.1: bridge window [mem 0xff600000-0xff6fffff pref] [ 0.486710] pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 0.486735] pci 0000:00:1c.0: setting latency timer to 64 [ 0.486774] pci 0000:00:1c.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17 [ 0.486796] pci 0000:00:1c.1: setting latency timer to 64 [ 0.486817] pci 0000:02:00.0: setting latency timer to 64 [ 0.486836] pci 0000:03:01.0: setting latency timer to 64 [ 0.486858] pci 0000:03:02.0: setting latency timer to 64 [ 0.486880] pci 0000:03:03.0: setting latency timer to 64 [ 0.486893] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7] [ 0.486902] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff] [ 0.486912] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff] [ 0.486922] pci_bus 0000:00: resource 7 [mem 0x80000000-0xffffffff] [ 0.486932] pci_bus 0000:01: resource 0 [io 0xe000-0xefff] [ 0.486941] pci_bus 0000:01: resource 1 [mem 0xd0100000-0xd01fffff] [ 0.486951] pci_bus 0000:01: resource 2 [mem 0xff700000-0xff7fffff pref] [ 0.486961] pci_bus 0000:02: resource 0 [io 0xd000-0xdfff] [ 0.486970] pci_bus 0000:02: resource 1 [mem 0xd0000000-0xd00fffff] [ 0.486980] pci_bus 0000:02: resource 2 [mem 0xff600000-0xff6fffff pref] [ 0.486989] pci_bus 0000:03: resource 0 [io 0xd000-0xdfff] [ 0.486998] pci_bus 0000:03: resource 1 [mem 0xd0000000-0xd00fffff] [ 0.487008] pci_bus 0000:03: resource 2 [mem 0xff600000-0xff6fffff 64bit pref] [ 0.487018] pci_bus 0000:04: resource 0 [io 0xd000-0xdfff] [ 0.487028] pci_bus 0000:04: resource 1 [mem 0xd0000000-0xd00fffff] [ 0.487038] pci_bus 0000:04: resource 2 [mem 0xff600000-0xff6fffff 64bit pref] [ 0.487177] NET: Registered protocol family 2 [ 0.487405] IP route cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.488397] TCP established hash table entries: 131072 (order: 8, 1048576 bytes) [ 0.489792] TCP bind hash table entries: 65536 (order: 7, 524288 bytes) [ 0.490493] TCP: Hash tables configured (established 131072 bind 65536) [ 0.490525] TCP reno registered [ 0.490551] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.490590] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.490898] NET: Registered protocol family 1 [ 0.490970] pci 0000:00:02.0: Boot video device [ 0.491052] pci 0000:00:1d.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20 [ 0.491092] pci 0000:00:1d.0: PCI INT A disabled [ 0.491134] pci 0000:00:1d.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21 [ 0.491174] pci 0000:00:1d.1: PCI INT B disabled [ 0.491220] pci 0000:00:1d.2: PCI INT C -> GSI 22 (level, low) -> IRQ 22 [ 0.491259] pci 0000:00:1d.2: PCI INT C disabled [ 0.491307] pci 0000:00:1d.7: PCI INT D -> GSI 23 (level, low) -> IRQ 23 [ 0.864431] Freeing initrd memory: 13820k freed [ 2.088042] pci 0000:00:1d.7: EHCI: BIOS handoff failed (BIOS bug?) 01010001 [ 2.088207] pci 0000:00:1d.7: PCI INT D disabled [ 2.088267] PCI: CLS 64 bytes, default 64 [ 2.089248] audit: initializing netlink socket (disabled) [ 2.089287] type=2000 audit(1349363630.084:1): initialized [ 2.144783] highmem bounce pool size: 64 pages [ 2.144808] HugeTLB registered 2 MB page size, pre-allocated 0 pages [ 2.160057] VFS: Disk quotas dquot_6.5.2 [ 2.160232] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 2.161716] fuse init (API version 7.17) [ 2.161995] msgmni has been set to 1713 [ 2.162925] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) [ 2.163008] io scheduler noop registered [ 2.163023] io scheduler deadline registered [ 2.163048] io scheduler cfq registered (default) [ 2.163339] pcieport 0000:00:1c.0: setting latency timer to 64 [ 2.163530] pcieport 0000:00:1c.1: setting latency timer to 64 [ 2.163706] pcieport 0000:02:00.0: setting latency timer to 64 [ 2.163873] pcieport 0000:03:01.0: setting latency timer to 64 [ 2.163964] pcieport 0000:03:01.0: irq 40 for MSI/MSI-X [ 2.164193] pcieport 0000:03:02.0: setting latency timer to 64 [ 2.164272] pcieport 0000:03:02.0: irq 41 for MSI/MSI-X [ 2.164453] pcieport 0000:03:03.0: setting latency timer to 64 [ 2.164531] pcieport 0000:03:03.0: irq 42 for MSI/MSI-X [ 2.164783] pcieport 0000:00:1c.0: Signaling PME through PCIe PME interrupt [ 2.164801] pci 0000:01:00.0: Signaling PME through PCIe PME interrupt [ 2.164816] pcie_pme 0000:00:1c.0:pcie01: service driver pcie_pme loaded [ 2.164853] pcieport 0000:00:1c.1: Signaling PME through PCIe PME interrupt [ 2.164867] pcieport 0000:02:00.0: Signaling PME through PCIe PME interrupt [ 2.164880] pcieport 0000:03:01.0: Signaling PME through PCIe PME interrupt [ 2.164892] pci 0000:04:00.0: Signaling PME through PCIe PME interrupt [ 2.164904] pcieport 0000:03:02.0: Signaling PME through PCIe PME interrupt [ 2.164917] pcieport 0000:03:03.0: Signaling PME through PCIe PME interrupt [ 2.164932] pcie_pme 0000:00:1c.1:pcie01: service driver pcie_pme loaded [ 2.164988] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 2.165115] pciehp 0000:00:1c.0:pcie04: HPC vendor_id 8086 device_id 8110 ss_vid 8086 ss_did 8119 [ 2.165177] pciehp 0000:00:1c.0:pcie04: service driver pciehp loaded [ 2.165199] pciehp 0000:00:1c.1:pcie04: HPC vendor_id 8086 device_id 8112 ss_vid 8086 ss_did 8119 [ 2.165260] pciehp 0000:00:1c.1:pcie04: service driver pciehp loaded [ 2.165290] pciehp: PCI Express Hot Plug Controller Driver version: 0.4 [ 2.165488] intel_idle: MWAIT substates: 0x3020220 [ 2.165508] intel_idle: v0.4 model 0x1C [ 2.165513] intel_idle: lapic_timer_reliable_states 0x2 [ 2.165519] Marking TSC unstable due to TSC halts in idle states deeper than C2 [ 2.165779] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input0 [ 2.165855] ACPI: Lid Switch [LID] [ 2.165983] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1 [ 2.166005] ACPI: Power Button [PWRB] [ 2.173811] thermal LNXTHERM:00: registered as thermal_zone0 [ 2.173829] ACPI: Thermal Zone [TZ00] (48 C) [ 2.174004] thermal LNXTHERM:01: registered as thermal_zone1 [ 2.174018] ACPI: Thermal Zone [TZ01] (34 C) [ 2.174194] thermal LNXTHERM:02: registered as thermal_zone2 [ 2.174207] ACPI: Thermal Zone [TZ02] (34 C) [ 2.174378] thermal LNXTHERM:03: registered as thermal_zone3 [ 2.174392] ACPI: Thermal Zone [TZ03] (34 C) [ 2.174503] ERST: Table is not found! [ 2.174513] GHES: HEST is not enabled! [ 2.174601] isapnp: Scanning for PnP cards... [ 2.176175] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled [ 2.196702] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 2.292409] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A [ 2.528909] isapnp: No Plug & Play device found [ 2.588733] 00:05: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 2.624523] 00:06: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A [ 2.640702] Linux agpgart interface v0.103 [ 2.645138] brd: module loaded [ 2.647452] loop: module loaded [ 2.648149] pata_acpi 0000:00:1f.1: setting latency timer to 64 [ 2.649238] Fixed MDIO Bus: probed [ 2.649315] tun: Universal TUN/TAP device driver, 1.6 [ 2.649327] tun: (C) 1999-2004 Max Krasnyansky <[email protected]> [ 2.649524] PPP generic driver version 2.4.2 [ 2.649824] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.649884] ehci_hcd 0000:00:1d.7: PCI INT D -> GSI 23 (level, low) -> IRQ 23 [ 2.649937] ehci_hcd 0000:00:1d.7: setting latency timer to 64 [ 2.649946] ehci_hcd 0000:00:1d.7: EHCI Host Controller [ 2.650082] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1 [ 2.650148] ehci_hcd 0000:00:1d.7: debug port 1 [ 2.654045] ehci_hcd 0000:00:1d.7: cache line size of 64 is not supported [ 2.654093] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xd02c4000 [ 2.668035] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00 [ 2.668392] hub 1-0:1.0: USB hub found [ 2.668413] hub 1-0:1.0: 8 ports detected [ 2.668618] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 2.668666] uhci_hcd: USB Universal Host Controller Interface driver [ 2.668726] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20 [ 2.668751] uhci_hcd 0000:00:1d.0: setting latency timer to 64 [ 2.668759] uhci_hcd 0000:00:1d.0: UHCI Host Controller [ 2.668910] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2 [ 2.668981] uhci_hcd 0000:00:1d.0: irq 20, io base 0x0000f040 [ 2.669335] hub 2-0:1.0: USB hub found [ 2.669355] hub 2-0:1.0: 2 ports detected [ 2.669508] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21 [ 2.669531] uhci_hcd 0000:00:1d.1: setting latency timer to 64 [ 2.669538] uhci_hcd 0000:00:1d.1: UHCI Host Controller [ 2.669675] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3 [ 2.669739] uhci_hcd 0000:00:1d.1: irq 21, io base 0x0000f020 [ 2.670099] hub 3-0:1.0: USB hub found [ 2.670118] hub 3-0:1.0: 2 ports detected [ 2.670271] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 22 (level, low) -> IRQ 22 [ 2.670295] uhci_hcd 0000:00:1d.2: setting latency timer to 64 [ 2.670302] uhci_hcd 0000:00:1d.2: UHCI Host Controller [ 2.670435] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4 [ 2.670502] uhci_hcd 0000:00:1d.2: irq 22, io base 0x0000f000 [ 2.670869] hub 4-0:1.0: USB hub found [ 2.670888] hub 4-0:1.0: 2 ports detected [ 2.671186] usbcore: registered new interface driver libusual [ 2.671332] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12 [ 2.673408] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 2.673437] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 2.673844] mousedev: PS/2 mouse device common for all mice [ 2.674272] rtc_cmos 00:08: RTC can wake from S4 [ 2.674482] rtc_cmos 00:08: rtc core: registered rtc_cmos as rtc0 [ 2.674529] rtc0: alarms up to one year, y3k, 242 bytes nvram, hpet irqs [ 2.674691] device-mapper: uevent: version 1.0.3 [ 2.674903] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: [email protected] [ 2.675024] EISA: Probing bus 0 at eisa.0 [ 2.675037] EISA: Cannot allocate resource for mainboard [ 2.675050] Cannot allocate resource for EISA slot 1 [ 2.675061] Cannot allocate resource for EISA slot 2 [ 2.675072] Cannot allocate resource for EISA slot 3 [ 2.675083] Cannot allocate resource for EISA slot 4 [ 2.675094] Cannot allocate resource for EISA slot 5 [ 2.675105] Cannot allocate resource for EISA slot 6 [ 2.675116] Cannot allocate resource for EISA slot 7 [ 2.675127] Cannot allocate resource for EISA slot 8 [ 2.675137] EISA: Detected 0 cards. [ 2.675161] cpufreq-nforce2: No nForce2 chipset. [ 2.675401] cpuidle: using governor ladder [ 2.675786] cpuidle: using governor menu [ 2.675797] EFI Variables Facility v0.08 2004-May-17 [ 2.676429] TCP cubic registered [ 2.676751] NET: Registered protocol family 10 [ 2.678031] NET: Registered protocol family 17 [ 2.678052] Registering the dns_resolver key type [ 2.678107] Using IPI No-Shortcut mode [ 2.678515] PM: Hibernation image not present or could not be loaded. [ 2.678543] registered taskstats version 1 [ 2.701145] Magic number: 0:84:234 [ 2.701312] rtc_cmos 00:08: setting system clock to 2012-10-04 15:13:51 UTC (1349363631) [ 2.702280] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found [ 2.702294] EDD information not available. [ 2.702858] Freeing unused kernel memory: 740k freed [ 2.703630] Write protecting the kernel text: 5816k [ 2.703692] Write protecting the kernel read-only data: 2376k [ 2.703706] NX-protecting the kernel data: 4424k [ 2.751226] udevd[84]: starting version 175 [ 2.980162] usb 1-1: new high-speed USB device number 2 using ehci_hcd [ 3.001394] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded [ 3.001474] r8169 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 3.001554] r8169 0000:01:00.0: setting latency timer to 64 [ 3.001654] r8169 0000:01:00.0: irq 43 for MSI/MSI-X [ 3.004220] r8169 0000:01:00.0: eth0: RTL8168c/8111c at 0xf8416000, 00:18:92:03:10:46, XID 1c4000c0 IRQ 43 [ 3.004254] r8169 0000:01:00.0: eth0: jumbo features [frames: 6128 bytes, tx checksumming: ko] [ 3.004347] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded [ 3.005085] r8169 0000:04:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18 [ 3.005182] r8169 0000:04:00.0: setting latency timer to 64 [ 3.005292] r8169 0000:04:00.0: irq 44 for MSI/MSI-X [ 3.007187] r8169 0000:04:00.0: eth1: RTL8168c/8111c at 0xf8418000, 00:18:92:03:10:47, XID 1c4000c0 IRQ 44 [ 3.007224] r8169 0000:04:00.0: eth1: jumbo features [frames: 6128 bytes, tx checksumming: ko] [ 3.034417] pata_sch 0000:00:1f.1: version 0.2 [ 3.034518] pata_sch 0000:00:1f.1: setting latency timer to 64 [ 3.036698] scsi0 : pata_sch [ 3.039842] scsi1 : pata_sch [ 3.040913] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xf060 irq 14 [ 3.040940] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xf068 irq 15 [ 3.131850] Initializing USB Mass Storage driver... [ 3.136405] scsi2 : usb-storage 1-1:1.0 [ 3.136642] usbcore: registered new interface driver usb-storage [ 3.136656] USB Mass Storage support registered. [ 3.524465] usb 3-1: new low-speed USB device number 2 using uhci_hcd [ 3.968144] usb 3-2: new full-speed USB device number 3 using uhci_hcd [ 4.137903] scsi 2:0:0:0: Direct-Access TS TS4GUFM-H 1100 PQ: 0 ANSI: 0 CCS [ 4.140067] sd 2:0:0:0: Attached scsi generic sg0 type 0 [ 4.140590] sd 2:0:0:0: [sda] 8028160 512-byte logical blocks: (4.11 GB/3.82 GiB) [ 4.141597] sd 2:0:0:0: [sda] Write Protect is off [ 4.141618] sd 2:0:0:0: [sda] Mode Sense: 43 00 00 00 [ 4.142974] sd 2:0:0:0: [sda] No Caching mode page present [ 4.143000] sd 2:0:0:0: [sda] Assuming drive cache: write through [ 4.145837] sd 2:0:0:0: [sda] No Caching mode page present [ 4.145858] sd 2:0:0:0: [sda] Assuming drive cache: write through [ 4.147931] sda: sda1 sda2 < sda5 > [ 4.150972] sd 2:0:0:0: [sda] No Caching mode page present [ 4.151001] sd 2:0:0:0: [sda] Assuming drive cache: write through [ 4.151023] sd 2:0:0:0: [sda] Attached SCSI disk [ 4.249168] input: HID 046a:004b as /devices/pci0000:00/0000:00:1d.1/usb3/3-1/3-1:1.0/input/input2 [ 4.249579] generic-usb 0003:046A:004B.0001: input,hidraw0: USB HID v1.11 Keyboard [HID 046a:004b] on usb-0000:00:1d.1-1/input0 [ 4.287805] input: HID 046a:004b as /devices/pci0000:00/0000:00:1d.1/usb3/3-1/3-1:1.1/input/input3 [ 4.289235] generic-usb 0003:046A:004B.0002: input,hidraw1: USB HID v1.11 Mouse [HID 046a:004b] on usb-0000:00:1d.1-1/input1 [ 4.297604] input: EloTouchSystems,Inc Elo TouchSystems 2216 AccuTouch\xffffffc2\xffffffae\xffffffae USB Touchmonitor Interface as /devices/pci0000:00/0000:00:1d.1/usb3/3-2/3-2:1.0/input/input4 [ 4.298913] generic-usb 0003:04E7:0050.0003: input,hidraw2: USB HID v1.00 Pointer [EloTouchSystems,Inc Elo TouchSystems 2216 AccuTouch\xffffffc2\xffffffae\xffffffae USB Touchmonitor Interface] on usb-0000:00:1d.1-2/input0 [ 4.299878] usbcore: registered new interface driver usbhid [ 4.299925] usbhid: USB HID core driver [ 4.352639] EXT4-fs (sda1): INFO: recovery required on readonly filesystem [ 4.352661] EXT4-fs (sda1): write access will be enabled during recovery [ 8.519257] EXT4-fs (sda1): recovery complete [ 8.564389] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) [ 14.280922] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 14.280944] ADDRCONF(NETDEV_UP): eth1: link is not ready [ 14.310368] udevd[308]: starting version 175 [ 14.353873] Adding 1045500k swap on /dev/sda5. Priority:-1 extents:1 across:1045500k [ 14.428718] lp: driver loaded but no devices found [ 14.521667] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro [ 15.073459] [drm] Initialized drm 1.1.0 20060810 [ 15.097073] psb_gfx: module is from the staging directory, the quality is unknown, you have been warned. [ 15.180630] gma500 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 15.180648] gma500 0000:00:02.0: setting latency timer to 64 [ 15.182117] Stolen memory information [ 15.182127] base in RAM: 0x7f800000 [ 15.182134] size: 7932K, calculated by (GTT RAM base) - (Stolen base), seems wrong [ 15.182143] the correct size should be: 8M(dvmt mode=3) [ 15.234889] Set up 1983 stolen pages starting at 0x7f800000, GTT offset 0K [ 15.235126] [drm] SGX core id = 0x01130000 [ 15.235135] [drm] SGX core rev major = 0x01, minor = 0x02 [ 15.235143] [drm] SGX core rev maintenance = 0x01, designer = 0x00 [ 15.268796] [Firmware Bug]: ACPI: No _BQC method, cannot determine initial brightness [ 15.269888] acpi device:04: registered as cooling_device2 [ 15.270568] acpi device:05: registered as cooling_device3 [ 15.270947] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:00/input/input5 [ 15.271238] ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no) [ 15.271424] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010). [ 15.271434] [drm] No driver support for vblank timestamp query. [ 15.374694] type=1400 audit(1349363644.167:2): apparmor="STATUS" operation="profile_load" name="/sbin/dhclient" pid=435 comm="apparmor_parser" [ 15.385518] type=1400 audit(1349363644.179:3): apparmor="STATUS" operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=435 comm="apparmor_parser" [ 15.386369] type=1400 audit(1349363644.179:4): apparmor="STATUS" operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" pid=435 comm="apparmor_parser" [ 15.677514] r8169 0000:01:00.0: eth0: link down [ 15.694828] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 16.537490] gma500 0000:00:02.0: allocated 800x480 fb [ 16.558066] fbcon: psbfb (fb0) is primary device [ 16.747122] gma500 0000:00:02.0: BL bug: Reg 00000000 save 00000000 [ 16.775550] Console: switching to colour frame buffer device 100x30 [ 16.781804] fb0: psbfb frame buffer device [ 16.781812] drm: registered panic notifier [ 16.870168] [drm] Initialized gma500 1.0.0 2011-06-06 for 0000:00:02.0 on minor 0 [ 16.871166] snd_hda_intel 0000:00:1b.0: power state changed by ACPI to D0 [ 16.871186] snd_hda_intel 0000:00:1b.0: power state changed by ACPI to D0 [ 16.871207] snd_hda_intel 0000:00:1b.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 16.871284] snd_hda_intel 0000:00:1b.0: setting latency timer to 64 [ 29.338953] r8169 0000:01:00.0: eth0: link up [ 29.339471] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 31.427223] init: failsafe main process (675) killed by TERM signal [ 31.522411] type=1400 audit(1349363660.316:5): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=889 comm="apparmor_parser" [ 31.523956] type=1400 audit(1349363660.316:6): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=889 comm="apparmor_parser" [ 31.524882] type=1400 audit(1349363660.320:7): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=889 comm="apparmor_parser" [ 31.525940] type=1400 audit(1349363660.320:8): apparmor="STATUS" operation="profile_load" name="/usr/sbin/tcpdump" pid=891 comm="apparmor_parser" [ 34.526445] postgres (1003): /proc/1003/oom_adj is deprecated, please use /proc/1003/oom_score_adj instead. [ 40.144048] eth0: no IPv6 routers present

  Read the article

• Snmpd update interface counters slowly or something like this

  - by Korjavin Ivan

  I update one my freebsd box to 9-stable (totally new installation) and install net-snmp for monitoring. uname -r 9.1-PRERELEASE pkg_info net-snmp-5.7.1_7 Information for net-snmp-5.7.1_7: Comment: An extendable SNMP implementation .... cat /var/db/ports/net-snmp/options # This file is auto-generated by 'make config'. # Options for net-snmp-5.7.1_7 _OPTIONS_READ=net-snmp-5.7.1_7 _FILE_COMPLETE_OPTIONS_LIST= IPV6 MFD_REWRITES PERL PERL_EMBEDDED PYTHON DUMMY TKMIB DMALLOC MYSQL AX_SOCKONLY UNPRIVILEGED OPTIONS_FILE_UNSET+=IPV6 OPTIONS_FILE_UNSET+=MFD_REWRITES OPTIONS_FILE_SET+=PERL OPTIONS_FILE_SET+=PERL_EMBEDDED OPTIONS_FILE_UNSET+=PYTHON OPTIONS_FILE_SET+=DUMMY OPTIONS_FILE_UNSET+=TKMIB OPTIONS_FILE_SET+=DMALLOC OPTIONS_FILE_UNSET+=MYSQL OPTIONS_FILE_UNSET+=AX_SOCKONLY OPTIONS_FILE_UNSET+=UNPRIVILEGED I have about 500 vlan on this machine, and collect info about interface through snmpd to 2 different software, zabbix and cacti. And both of them plot the graphs with blank fields. I tryed change polling time in zabbix, from 15, sec to 30,60,90,120,10. And anyway i have blank fields. snmpd.conf is empty - only a access controls. This configuration worked fine on freebsd 8. Where is my fault? How fix this graphs? UPD: Changing pooling time, switch off one of agent, doesnt help. I look at zabbix log (recieved data from snmpd) and see that: sorry for russian locale, just look at numbers: and thats is not true, as my "iftop" show speed was about 90Mbits, but snmpd return 2Mbits. I understand that snmpd doesnt return speed, it return just a counter. But how its possible? why 2Mbit/s ? I tryed recompile snmpd with 64-bit counters, and without it. In both variants this blank fields present. So i think its my OS (freebsd) doesnt update interface counters well. I still collect tcpdump for found this request/response. But have problem with that, to much trash. UPD2: I decrypt tcpdump-ed file, and public this as google doc at gdocfile Timediff looks strange.. Like zabbix sometimes "forget" do request, and then do twice at row, ehh UPD3: I parse log from command "while true; do netstat -bin -I vlan4008 /var/log/netstat; sleep 300; done" and load as google docs, and add formula for speed : link Looks like all counters in OS are good. Now i think problem in : 1. zabbix get request twice at row (and what about cacti) 2. snmpd use counter32

  Read the article

• Persistent Issues on small business network using Cisco 871W and Catalyst Express 500

  - by Ben Campbell

  Being the most qualified (read: still not qualified) to solve our persistant network issues, I've turned to serverfault for guidance. I've done some searching, reading related documentation on cisco.com and tried a bit of troubleshooting. Here is the config: 100mb synchronous connection from a business internet provider (tested multiple times at 100meg at the source) Cisco 871W wireless point & router is where the WAN connection starts (this serves all our wireless). The only wired connection in the 871W is the Catalyst switch listed below. Cisco Catalyst Express 500 (24TT) is where all the wired connections terminate. About 20 Windows workstations and servers (AD/Webservers only). Some services in EC2 including mail and other web servers/apps. I've been TOLD cabling internally should be gigabit-ready. Here are the problems: generally slow download rates from the internet to the desktop/laptop frequent "page cannot be displayed" errors in browsers-sometimes 3 or 4 reloads are necessary... often times CSS wont load or other content requiring the browser to connect to a different server. slow speed within the LAN from workstation to workstation copying files. I would expect extremely fast data transfer workstation to workstation / server to workstation in this simple network. Several things I need to admit: I'm not primarily a network guy. Funding is relatively low, I need to be the guy that finds the solution. I understand most of the terminology and most of the technology. Implementation is where I fail due to lack of experience. Getting to the point: I'm wondering whether experienced network admins think that our small network should be sufficiently served with our current hardware if configured properly... or if we should purchase new equipment and start fresh? If starting fresh is the plan, whatever that new equipment may be is a likely different question entirely. If I haven't provided enough information, I will happily do some troubleshooting and update with the results. I have experience using wireshark and some other tools. Please let me know what you think would be most helpful and thanks in advance. EDIT: I forgot to add that the Cisco applicance will not finish loading the SDM Express console. It hangs every time at the "populating modules... DHCP". It eventually crashes and closes. I've rebooted the hardware and this still happens.

  Read the article

• Squid 2.7.STABLE3-4.1 as a transparent proxy on Ubuntu Server 9.04

  - by LOGIC9

  Can't get this to work at all! I'm trying to get this linux box to act as a transparent proxy and, with the help of DHCP, force everyone on the network to gate into the proxy. I have two ethernet connections, both to the same switch. And I'm trying to get 192.168.1.234 to become the default gateway. The actual WAN connection is to a gateway 192.168.1.1. eth0 is 192.168.1.234 eth1 is 192.168.1.2 Effectively I'm trying to make eth0 a LAN only interface and eth1 a WAN interface. I've oi should set the gateway for eth1 to point to 192.168.1.234 my squid.conf file has the following directives added at the bottom: nly set eth0 to have a gateway address in /etc/network/interfaces I'm not sure whether http_port 3128 transparent acl lan src 192.168.1.0/24 acl lh src 127.0.0.1/255.255.255.0 http_access allow lan http_access allow lh i've added the following routing commands: iptables -t nat -A PREROUTING -i eth0 -p tcp -m tcp --dport 80 -j DNAT --to-destination 192.168.1.2:3128 iptables -t nat -A PREROUTING -i eth1 -p tcp -m tcp --dport 80 -j REDIRECT --to-ports 3128 I set a computer with TCP settings 192.168.1.234 as the gateway and opened up google.com, but it comes up with a request error. Any ideas why this isn't working? :( Been searching continuously for a solution to no avail. ----------------------------- EDIT ------------------------------- Managed to get it to route properly to the squid, here's the error I get in the browser: ERROR The requested URL could not be retrieved While trying to process the request: GET / HTTP/1.1 Host: www.google.com User-Agent: Mozilla/5.0 (Windows; U; Windows NT 5.1; en-GB; rv:1.9.1.2) Gecko/20090729 Firefox/3.5.2 Accept: text/html,application/xhtml+xml,application/xml;q=0.9,*/*;q=0.8 Accept-Language: en-gb,en;q=0.5 Accept-Encoding: gzip,deflate Accept-Charset: ISO-8859-1,utf-8;q=0.7,*;q=0.7 Keep-Alive: 300 Connection: keep-alive Cache-Control: max-age=0 The following error was encountered: * Invalid Request Some aspect of the HTTP Request is invalid. Possible problems: * Missing or unknown request method * Missing URL * Missing HTTP Identifier (HTTP/1.0) * Request is too large * Content-Length missing for POST or PUT requests * Illegal character in hostname; underscores are not allowed Your cache administrator is webmaster. Generated Mon, 26 Oct 2009 03:41:15 GMT by mjolnir.lloydharrington.local (squid/2.7.STABLE3)

  Read the article

• Cannot read status the monit daemon, even with allowed group

  - by jefflunt

  I cannot seem to get monit status or other CLI commands to work. I've built monit v5.8 to run on a Raspberry Pi. I'm able to add services to be monitored, and the web interface can be accessed just fine, as I've set it up for public read-only access (it's a test server, not my final production setup, so not a big deal right now). Problem is, when I run monit status while logged in as root I get: # monit status monit: cannot read status from the monit daemon I also have monit started on boot via this /etc/inittab file entry: mo:2345:respawn:/usr/local/bin/monit -Ic /etc/monitrc I've verified that monit is running, and I'm getting email alerts anytime I either kill the monit process manually, or reboot my raspberry pi. So, next I check my monitrc file permissions to see which group is allowed access. # ls -al /etc/monitrc -rw------- 1 root root 2359 Aug 24 14:48 /etc/monitrc Here's my relevant allow section of the control file. set httpd port 80 allow [omitted] readonly allow @root allow localhost allow 0.0.0.0/0.0.0.0 Also tried setting permissions on this file to 640 to allow group read permissions, but no matter what I try I either get the same error as noted above, or when the permissions are set to 640 I get: # monit status monit: The control file '/etc/monitrc' must have permissions no more than -rwx------ (0700); right now permissions are -rw-r----- (0640). What am I missing here? I know that the httpd must be enabled, as that's the interface that the CLI uses to get information (or so I've read), so I've done that. And in terms of monit doing its monitoring job and sending email alerts, that's all working as well. Here's my entire monitrc file - again, this is version v5.8, and it was build with both PAM and SSL support. The process runs under the root user: # Global settings set daemon 300 with start delay 5 set logfile /var/log/monit.log set pidfile /var/run/monit.pid set idfile /var/run/.monit.id set statefile /var/run/.monit.state # Mail alerts ## Set the list of mail servers for alert delivery. Multiple servers may be ## specified using a comma separator. If the first mail server fails, Monit # will use the second mail server in the list and so on. By default Monit uses # port 25 - it is possible to override this with the PORT option. # set mailserver smtp.gmail.com port 587 username [omitted] password [omitted] using tlsv1 ## Send status and events to M/Monit (for more informations about M/Monit ## see http://mmonit.com/). By default Monit registers credentials with ## M/Monit so M/Monit can smoothly communicate back to Monit and you don't ## have to register Monit credentials manually in M/Monit. It is possible to ## disable credential registration using the commented out option below. ## Though, if safety is a concern we recommend instead using https when ## communicating with M/Monit and send credentials encrypted. # # set mmonit http://monit:[email protected]:8080/collector # # and register without credentials # Don't register credentials # # ## Monit by default uses the following format for alerts if the the mail-format ## statement is missing:: set mail-format { from: [email protected] subject: $SERVICE $DESCRIPTION message: $EVENT Service: $SERVICE Date: $DATE Action: $ACTION Host: $HOST Description: $DESCRIPTION Monit instance provided by chicagomeshnet.com } # Web status page set httpd port 80 allow [omitted] readonly allow @root allow localhost allow 0.0.0.0/0.0.0.0 ## You can set alert recipients whom will receive alerts if/when a ## service defined in this file has errors. Alerts may be restricted on ## events by using a filter as in the second example below.

  Read the article

• Parsing xml files locally from assets folder using XmlPullParser

  - by Randolphg

  Im trying to parse a local xml file that I place in my assets folder. I've been trying to do this for almost a week now. Here is my test xml file Test1 Test2 Test3 Test4 Test5 I keep getting the same error: W/System.err(22458): org.xmlpull.v1.XmlPullParserException: unexpected type (position:TEXT Code: public void xmlParser() throws XmlPullParserException, IOException, ParserConfigurationException, SAXException { Log.d("tag", "xmlParsing...."); Arithmetic arthm = new Arithmetic(); XmlPullParserFactory xmlPF = XmlPullParserFactory.newInstance(); xmlPF.setValidating(false); XmlPullParser xml = xmlPF.newPullParser(); InputStream raw = getApplication().getAssets().open("menu.xml"); xml.setInput(raw, null); xml.nextTag(); Log.d("tag", "start parsing...."); String elementText = null; String elemName = null; int nofTags = 0; while (xml.getEventType() != XmlPullParser.END_DOCUMENT) { Log.d("tag", "while(xml.next)..."); switch (xml.getEventType()) { case XmlPullParser.START_DOCUMENT: Log.d("tag", "while (xml.getEventType() != XmlPullParser.END_DOCUMENT)"); break; case XmlPullParser.START_TAG: Log.d("tag", " case XmlPullParser.START_TAG"); elementText = xml.getName(); Log.d("tag", "elementText = " + elementText); if (xml.getEventType() != XmlPullParser.END_TAG) { xml.nextTag(); } break; case XmlPullParser.TEXT: Log.d("tag", "case TEXT"); if (elementText.equals("menu") && xml.isWhitespace()) { Log.d("tag", "<" + elementText + ">"); arthm.menu_name = xml.getText(); Log.d("tag", "value " + xml.getText() + " added"); } else if (elementText.equals("item")) { arthm.description = xml.getText(); Log.d("tag", "value " + xml.getText() + " added"); } else if (elementText.equals("SUBCATEGORY NAME")) { arthm.subcategoryDesc.add(xml.getText()); Log.d("tag", "value " + xml.getText() + " added"); } else if (elementText.equals("SUBCATEGORY DESC")) { arthm.subcategoryName.add(xml.getText()); Log.d("tag", "value " + xml.getText() + " added"); } break; case XmlPullParser.END_TAG: Log.d("tag", "case END_TAG"); nofTags += 1; String tags = Integer.toString(nofTags); Log.d("tags", elementText + " number of tags" + tags); if (xml.nextTag() != XmlPullParser.START_TAG) { xml.next(); } break; case XmlPullParser.END_DOCUMENT: Log.d("tag", "case END_DOCUMENT"); break; default: break; } } Log.d("tag", "Success!"); } Thanks in advance.

  Read the article

• Persuading openldap to work with SSL on Ubuntu with cn=config

  - by Roger

  I simply cannot get this (TLS connection to openldap) to work and would appreciate some assistance. I have a working openldap server on ubuntu 10.04 LTS, it is configured to use cn=config and most of the info I can find for TLS seems to use the older slapd.conf file :-( I've been largely following the instructions here https://help.ubuntu.com/10.04/serverguide/C/openldap-server.html plus stuff I've read here and elsewhere - which of course could be part of the problem as I don't totally understand all of this yet! I have created an ssl.ldif file as follows; dn:cn=config add: olcTLSCipherSuite olcTLSCipherSuite: TLSV1+RSA:!NULL add: olcTLSCRLCheck olcTLSCRLCheck: none add: olcTLSVerifyClient olcTLSVerifyClient: never add: olcTLSCACertificateFile olcTLSCACertificateFile: /etc/ssl/certs/ldap_cacert.pem add: olcTLSCertificateFile olcTLSCertificateFile: /etc/ssl/certs/my.domain.com_slapd_cert.pem add: olcTLSCertificateKeyFile olcTLSCertificateKeyFile: /etc/ssl/private/my.domain.com_slapd_key.pem and I import it using the following command line ldapmodify -x -D cn=admin,dc=mydomain,dc=com -W -f ssl.ldif I have edited /etc/default/slapd so that it has the following services line; SLAPD_SERVICES="ldap:/// ldapi:/// ldaps:///" And everytime I'm making a change, I'm restarting slapd with /etc/init.d/slapd restart The following command line to test out the non TLS connection works fine; ldapsearch -d 9 -D cn=admin,dc=mydomain,dc=com -w mypassword \ -b dc=mydomain,dc=com -H "ldap://mydomain.com" "cn=roger*" But when I switch to ldaps using this command line; ldapsearch -d 9 -D cn=admin,dc=mydomain,dc=com -w mypassword \ -b dc=mydomain,dc=com -H "ldaps://mydomain.com" "cn=roger*" This is what I get; ldap_url_parse_ext(ldaps://mydomain.com) ldap_create ldap_url_parse_ext(ldaps://mydomain.com:636/??base) ldap_sasl_bind ldap_send_initial_request ldap_new_connection 1 1 0 ldap_int_open_connection ldap_connect_to_host: TCP mydomain.com:636 ldap_new_socket: 3 ldap_prepare_socket: 3 ldap_connect_to_host: Trying 127.0.0.1:636 ldap_pvt_connect: fd: 3 tm: -1 async: 0 TLS: can't connect: A TLS packet with unexpected length was received.. ldap_err2string ldap_sasl_bind(SIMPLE): Can't contact LDAP server (-1) Now if I check netstat -al I can see; tcp 0 0 *:www *:* LISTEN tcp 0 0 *:ssh *:* LISTEN tcp 0 0 *:https *:* LISTEN tcp 0 0 *:ldaps *:* LISTEN tcp 0 0 *:ldap *:* LISTEN I'm not sure if this is significant as well ... I suspect it is; openssl s_client -connect mydomain.com:636 -showcerts CONNECTED(00000003) 916:error:140790E5:SSL routines:SSL23_WRITE:ssl handshake failure:s23_lib.c:188: I think I've made all my certificates etc OK and here are the results of some checks; If I do this; certtool -e --infile /etc/ssl/certs/ldap_cacert.pem I get Chain verification output: Verified. certtool -e --infile /etc/ssl/certs/mydomain.com_slapd_cert.pem Gives "certtool: the last certificate is not self signed" but it otherwise seems OK? Where have I gone wrong? Surely getting openldap to run securely on ubuntu should be easy and not require a degree in rocket science! Any ideas?

  Read the article

• SMPS stops when I plug in a SATA drive?

  - by claws

  Hello, Part 1: my first question is all the 4 wire power connectors (intended for hardisks/dvd drives not mother board) are same. Right? I've been using all of them same and I had no problem for years. Yesterday I borrowed a SATA disk from my friend and connected it my computer using Sata Power adaptor (4 wire) and when I switched on the computer. There were fumes coming out of the connector. I immediately turned it off (in just one second). I tested the voltages in the 4 wire power connector of my SMPS: They were 5.3v & 12.2V. I couldn't measure the current. But my SMPTS label reads: DC Output: 3.3v (25A) +5v (32A) -5v (0.3A) +12V (17A) -12V (0.8A) And the SATA hardisk label reads Input: +5v (0.72A) +12V (0.52A) I'm shocked! I never noticed this. Does the "sata power adaptor" scale down the current to required? If it doesn't, I've been connecting same way for years. I never had any problem. This is the first time I'm encountering it. Part 2: I wanted to return the drive to my friend. He has two hard disks, SATA & PATA. Its the SATA that I borrowed. When he usually switches on. The CPU fan starts & then stops for a sec and starts again and continues working. That was the earlier situation. I don't know why it stops & starts? Well, Now when I connect this SATA disk and switch ON the computer. CPU fan starts (just for an instant, not even a 0.5 sec) and stops. It doesn't start again, I mean the power from SMPS has stopped. But if I disconnect this SATA disk. It works fine. What seems to be the problem? I've no idea about why there were fumes or why his SMPS starts & stops giving power? What is its relation with the SATA disk connection?

  Read the article

• Xubuntu login hangs after Cancel Button click

  - by akester

  I'm running Xubuntu 12.04 (I installed using the alternative installer.) running in Virtaulbox 4.1.20 My issue is with the login screen (lightdm-gtk-greeter). It usually runs just fine, and allows users to log in and out but it will hang if the user presses the cancel button. The interface is still working (ie, shutdown menu is still available, I can switch to a different tty) but the username or password field (depending on when the button is hit) is disabled. Restarting lightdm will reset the screen, but the problem still exists. The issue is only with the cancel button. The login, session, and language buttons/menus as well as the accessibility and shutdown menu appear to work normally. I've modified some of the config files for lighdm-gtk-greeter, specifically /etc/lightdm/lighdm-gtk-greeter.conf to change the background image and /etc/lightdm/lightdm.conf to disable the user list. I did not check to see if the error existed before the changes took place. The changes have been restored the default settings but the problem persists. Here is the output of /var/log/lightdm/lightdm.log when the screen is hung: [+0.00s] DEBUG: Logging to /var/log/lightdm/lightdm.log [+0.00s] DEBUG: Starting Light Display Manager 1.2.1, UID=0 PID=2072 [+0.00s] DEBUG: Loaded configuration from /etc/lightdm/lightdm.conf [+0.00s] DEBUG: Using D-Bus name org.freedesktop.DisplayManager [+0.00s] DEBUG: Registered seat module xlocal [+0.00s] DEBUG: Registered seat module xremote [+0.00s] DEBUG: Adding default seat [+0.00s] DEBUG: Starting seat [+0.00s] DEBUG: Starting new display for greeter [+0.00s] DEBUG: Starting local X display [+0.02s] DEBUG: Using VT 7 [+0.02s] DEBUG: Activating VT 7 [+0.03s] DEBUG: Logging to /var/log/lightdm/x-0.log [+0.04s] DEBUG: Writing X server authority to /var/run/lightdm/root/:0 [+0.04s] DEBUG: Launching X Server [+0.05s] DEBUG: Launching process 2078: /usr/bin/X :0 -auth /var/run/lightdm/root/:0 -nolisten tcp vt7 -novtswitch [+0.05s] DEBUG: Waiting for ready signal from X server :0 [+0.05s] DEBUG: Acquired bus name org.freedesktop.DisplayManager [+0.05s] DEBUG: Registering seat with bus path /org/freedesktop/DisplayManager/Seat0 [+0.28s] DEBUG: Got signal 10 from process 2078 [+0.28s] DEBUG: Got signal from X server :0 [+0.28s] DEBUG: Connecting to XServer :0 [+0.29s] DEBUG: Starting greeter [+0.29s] DEBUG: Started session 2082 with service 'lightdm', username 'lightdm' [+0.36s] DEBUG: Session 2082 authentication complete with return value 0: Success [+0.36s] DEBUG: Greeter authorized [+0.36s] DEBUG: Logging to /var/log/lightdm/x-0-greeter.log [+0.36s] DEBUG: Session 2082 running command /usr/lib/lightdm/lightdm-greeter-session /usr/sbin/lightdm-gtk-greeter [+0.58s] DEBUG: Greeter connected version=1.2.1 [+0.58s] DEBUG: Greeter connected, display is ready [+0.58s] DEBUG: New display ready, switching to it [+0.58s] DEBUG: Activating VT 7 [+1.04s] DEBUG: Greeter start authentication for andrew [+1.04s] DEBUG: Started session 2137 with service 'lightdm', username 'andrew' [+1.09s] DEBUG: Session 2137 got 1 message(s) from PAM [+1.09s] DEBUG: Prompt greeter with 1 message(s) [+17.24s] DEBUG: Cancel authentication [+17.24s] DEBUG: Session 2137: Sending SIGTERM

  Read the article

• Python in command line runs the wrong version?

  - by Deflect

  I have several versions of Python installed on a Windows 7 computer. I want to run Python 2.7 by default, but for whatever reason, typing python in the command line runs Python version 2.4.5. I've tried adding C:\Python27 to my system path variable as per this question, and manually combed my path variable it to make sure Python 2.4.5 wasn't tossed in there by mistake, but that didn't fix the issue. I have to type in C:\Python27\python.exe every time I want to access the correct version of python I want. What other places can I check? How can I make the command line use the correct version of python? I also found this but it's not for windows. [EDIT] My path (separated by semicolons): C:\Program Files\Common Files\Microsoft Shared\Windows Live; C:\Program Files (x86)\Common Files\Microsoft Shared\Windows Live; C:\Windows\system32; C:\Windows; C:\Windows\System32\Wbem; C:\Windows\System32\WindowsPowerShell\v1.0\; C:\Program Files\Dell\DW WLAN Card\Driver; C:\Program Files (x86)\Common Files\Roxio Shared\DLLShared\; C:\Program Files (x86)\Windows Live\Shared; c:\Program Files (x86)\Microsoft SQL Server\100\Tools\Binn\; c:\Program Files\Microsoft SQL Server\100\Tools\Binn\; c:\Program Files\Microsoft SQL Server\100\DTS\Binn\; C:\Program Files\TortoiseGit\bin; C:\Program Files\Java\jdk1.6.0_26\bin; C:\Program Files\Java\jdk1.6.0_21 ; C:\Program Files\IVI Foundation\VISA\Win64\Bin\; C:\Program Files (x86)\IVI Foundation\VISA\WinNT\Bin\; C:\Program Files (x86)\IVI Foundation\VISA\WinNT\Bin; C:\Program Files\WPIJavaCV\OpenCV_2.2.0\bin; C:\Program Files (x86)\LilyPond\usr\bin; C:\Program Files\TortoiseSVN\bin; C:\Program Files (x86)\doxygen\bin; C:\Program Files (x86)\Graphviz 2.28\bin; C:\Users\Michael\bin\Misc\cppcheck\; C:\Program Files (x86)\Git\cmd; C:\Python27\python.exe; C:\Ruby192\bin; C:\Users\Michael\AppData\Roaming\cabal\bin; C:\Python27\; [EDIT 2] Running python spews this out: 'import site' failed; used -v for traceback Python 2.4.5 (#1, Jul 22 2011, 02:01:04) [GCC 4.1.1] on mingw32 Type "help", "copyright", "credits" or "license" for more information. >>> ...and running python --version (as suggested below) seems to be an unrecognized option. (I also tried running python -v, and it appears that Python 2.4 is trying to import libraries from C:\Python27\Lib, and failed due to a syntax error when it encountered a with statement, which was added in later version, I think) Also, I'm not sure if it's significant or not, but the above python version says something about GCC and mingw32, while running C:\python27\python.exe shows this: Python 2.7.2 (default, Jun 12 2011, 15:08:59) [MSC v.1500 32 bit (Intel)] on win32 Type "help", "copyright", "credits" or "license" for more information. >>>>

  Read the article

• What "pieces" are needed in order to set up a cluster of physical servers?

  - by Chris Dutrow

  Background: Currently, we use Rackspace cloud servers. We have no intention to stop using them, but would like to look into setting up a cluster of physical servers (probably desktop computers in the $400 range with 8gb memory each) to offset some of our load and work as a secondary, more powerful, less reliable system. To put things in perspective, we can buy comparable desktop computers for the same price as we pay in one month to rent them on Rackspace Cloud. I understand that this is generally a dumb idea. However, in this particular instance, the server cluster is needed for its computation power. It is not mission-critical, it does not host a consumer-facing website, and if it goes down for a day or two, its not really a problem. Currently, we have access to business class verizon fios. If I understand correctly, we can get at least 25 dedicated IP addresses with this service, this should be enough. Requirements: Each server runs Linux Centos 6.3 Some of the servers run Python and execute processes from a task queue (Redis or RabbitMQ) Some of the servers are capable of serving static files and Python driven REST APIs Some of the servers host a Cassandra database cluster One or more of the servers are a Redis database servers One or more of the servers are PostgreSQL servers Questions: What kind of router or switch is needed? We would like the computers to be able to communicate effectively with each other via internal IP addresses. This is especially important for communicating with servers hosting Redis that need to be able to respond to requests very quickly. Are there special switches or routers that need to be used to connect the servers together? Are Desktop computers ok for this? We have found that we are mostly RAM-bottle necked, I understand that some servers have highly superior CPUs, but I'm not sure we need CPU power as much as we need RAM, which is cheap in Desktop computers. Will we have problems with the WIFI cards in the desktops or any other unexpected hardware limitation? What tools should be used to "image" the servers. For example, when we get an installation right for a Redis server or Cassandra node, are there tools that come with Linux Centos 6.3 to image the server to a USB drive or something like that? Or do we need to use some other software for this? What other things are we missing that we should be concerned about? Thanks so much!

  Read the article

• VPN - force a selective range of ip to run on VPN (linux)

  - by Francesco

  Preface: I know there are similar question here and there however I'm a kind of newbie on Net stuff so I need an answer on this specific scenario, hoping that can help others too as it is a common problem Let say I cannot do anything on the local switch to change the local ip range, I don't want to use any complicate trick as use VMachine to hide the local ip range but I want to use net tools to solve the issue. Scenario my local net assign me an IP of this class 192.168.1.xxx (ex. 192.168.1.116) and my VPN (VPNC) assign me IP of same class 192.168.1.xxx (ex. 192.168.1.247) Obviously I need VPN to access local address (ex. 192.168.1.100) but when I open any address of the class 192.168.1.xx the route point to my local net and not to the VPN ones. I'm on linux and i'd like gui solution (network manager) in case it is not possible let play with route command. here what network manager offer me: Here my actual route once connected to the VPN: Here some route information (route -n) Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 0.0.0.0 0.0.0.0 U 0 0 0 ppp0 169.254.0.0 0.0.0.0 255.255.0.0 U 1000 0 0 wlan0 182.71.21.106 192.168.1.1 255.255.255.255 UGH 0 0 0 wlan0 182.71.21.106 192.168.1.1 255.255.255.255 UGH 0 0 0 wlan0 192.168.1.0 0.0.0.0 255.255.255.0 U 9 0 0 wlan0 192.168.1.246 0.0.0.0 255.255.255.255 UH 0 0 0 ppp0 Here my ifconfig : ppp0 Link encap:Point-to-Point Protocol inet addr:192.168.1.247 P-t-P:192.168.1.246 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1400 Metric:1 RX packets:3415 errors:0 dropped:0 overruns:0 frame:0 TX packets:2525 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:3 RX bytes:3682328 (3.6 MB) TX bytes:402315 (402.3 KB) wlan0 Link encap:Ethernet HWaddr 4c:eb:42:06:a3:a6 inet addr:192.168.1.116 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::4eeb:42ff:fe06:a3a6/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:72598 errors:0 dropped:0 overruns:0 frame:0 TX packets:42300 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:76000532 (76.0 MB) TX bytes:13919400 (13.9 MB) The Question So basically I would like to add a rule to force this particular address (192.168.1.100) on the VPN and not on my local net

  Read the article

• Open ports broken from internal network

  - by ksvi

  Quick summary: Forwarded port works from the outside world, but from the internal network using the external IP the connection is refused. This is a simplified situation to make the explanation easier: I have a computer that is running a service on port 12345. This computer has an internal IP 192.168.1.100 and is connected directly to a modem/router which has internal IP 192.168.1.1 and external (public, static) IP 1.2.3.4. (The router is TP-LINK TD-w8960N) I have set up port forwarding (virtual server) at port 12345 to go to port 12345 at 192.168.1.100. If I run telnet 192.168.1.100 12345 from the same computer everything works. But running telnet 1.2.3.4 12345 says connection refused. If I do this on another computer (on the same internal network, connected to the router) the same thing happens. This would seem like the port forwarding is not working. However... If I run a online port checking service on my external IP and the service port it says the port is open and I can see the remote server connecting and immediately closing connection. And using another computer that is connected to the internet using a mobile connection I can also use telnet 1.2.3.4 12345 and I get a working connection. So the port forwarding seems to be working, however using external IP from the internal network doesn't. I have no idea what can be causing this, since another setup very much like this (different router) works for me. I can access a service running on a server from inside the network both through the internal and external IP. Note: I know I could just use the internal IP inside of the network to access this service. But if I have a laptop that must be able to do this both from inside and outside it would be annoying to constantly switch between 1.2.3.4 and 192.168.1.100 in the software configuration. Router output: > iptables -t nat -L -n Chain PREROUTING (policy ACCEPT) target prot opt source destination ACCEPT all -- 0.0.0.0/0 224.0.0.0/3 DNAT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:25 to:192.168.1.101 DNAT udp -- 0.0.0.0/0 0.0.0.0/0 udp dpt:25 to:192.168.1.101 DNAT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:110 to:192.168.1.101 DNAT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:12345 to:192.168.1.102 DNAT udp -- 0.0.0.0/0 192.168.1.1 udp dpt:53 to:217.118.96.203 Chain POSTROUTING (policy ACCEPT) target prot opt source destination MASQUERADE all -- 192.168.1.0/24 0.0.0.0/0 Chain OUTPUT (policy ACCEPT) target prot opt source destination

  Read the article

• What are some of the best wireless routers for a price-conscious home power-user?

  - by Alain

  I'm extremely dissatisfied with the 'popular' choice for routers in homes and small offices. They are expensive (upwards of 60$), lack a great deal of useful configuration options, and seem to need to be restarted quite often. (Linksys comes to mind). I've been on the market for a good router lately, and slowly collecting a set of requirements I feel good routers should meet. Maximum number of TCP/IP connections. - This isn't something I see any routers advertise, but in terms of supporting torrent applications, I've been screwed by routers that support less than 20 here. From what I understand a fairly standard number is 200, but there are not so expensive routers that support thousands. Router configuration menu - Most have standard menu's that let you set up basic things like your wireless network encryption settings, uPnP, and maybe even DMZ (demilitarized zones). An absolute requirement for me, however, are routers with good enough firmware to support: Explicit Port forwarding Assigning static local ips to specific mac addresses, or at least Port forwarding by MAC address Port, IP and MAC filtering Dynamic DNS service for home users who want to set up a server but have a dynamic IP Traffic shaping (ideally) - giving priority to packets from certain machines or over certain ports. Strong wireless signal - If getting a reliable signal requires me to be so close to the router that I can connect an Ethernet cable, it's not good enough. As many Ethernet ports as possible. - Because I want to be able to switch from console gaming to PC gaming without visiting my router. So far, the best thing I've stumbled upon (in the bargain bin at staples) was a 20$ retail plus router. It was meant to be the cheapest alternative until I could find something better to purchase online, but I was actually blown away by the firmware capabilities. It supports defining reserved bandwidth for certain network traffic, dynamic DNS, reserving local IPs for specific MAC addresses, etc. At 2 am when my roommate is killing our Internet with their torrents, I can limit their bandwidth without outright blacklisting them. I have, however, met serious limitations when it comes to network traffic between local machines. It claims a 300Mbps connection, but I have trouble streaming videos from my PC to my console or other laptops wirelessly. It has a meltdown and needs to be reset once in a while (no more than a couple times a month), and it's got a 200 connection limit. There 4 Ethernet ports in the back but I'm pretty sure the first doesn't work. So some great answers to this question would be: Any metrics you use to compare routers, and requirements you have for new candidates. The best routers you've found for supporting home servers, file management systems, high volume torrent traffic, good price/feature ratio, etc. Good configuration advice (aside from 'use Ethernet whenever possible') Thanks for your feedback and experiences!

  Read the article

• 2 Servers setup for redundency, backup

  - by minal

  I presently have 1 dedicated virtual server running my website/blog/mail, etc. This is on Hyper-V with 512MB RAM. Windows Web2008. With the VM, I have these running within it: SmarterMail – for emails MS DNS – I have my own nameservers on this server SQL Express IIS7 2 IP Address I have now leased 2 physical servers : P4 2.6Ghz 1GB RAM 80GB HDD. With these new servers, I get 2 IPs per server as well. These are running Windows 2008 Standard. With the VM the HDD was obviously on a RAID setup so I was not worried about hardware issues as it fell on the provider to manage. However, with the new servers the HDD is not RAID’d, hence my concern is that if it fails I need a backup position. What would be the most ideal setup to go for? I am thinking: Server 1: (Web/PrimaryDNS) DNS – NS1 SQL Express – OFF turn on when required, ie. Server2 is down SmarterMail – OFF turn on when required, ie. Server2 is down IIS 7 Server2:(SQL/Backup) DNS – NS2 SQL Web Edition SmarterMail IIS 7 How can I set it up so that if 1 goes down I can have everything on 2 instantly or by manual switching over. I am confused as other DNS servers will cache the web servers IP address for requests, and if that server goes down, the backup server will have a different IP. How do I make this work? I will be doing routine backups, in which case I will keep copies of backups on both servers. If I am copying the same stuff on both servers like a mirror then I am losing on using the true performance out of it. It's like 1 server is always on standby. Ideally I want SQL and web on 2 diff machines for best performance. If Server1 goes down, I should be able to switch to Server2 fairly easily. I don't have a problem with manual intervention to start the sql/mail services, etc. In terms of scalabilty, the VM has coped pretty well to date. Moving forward the SQL and IIS workload is going to double pretty quickly. Some ideas would be great.

  Read the article

• Ubuntu 10.04 LTS - Dual monitor works only sometimes (ATI multi-desktop)

  - by Beres Botond

  I've been using my laptop with an external LCD monitor attached to it at work (Philips 201E). And at home with a different external monitor (Samsung 2032BW). I have an ATI graphics card (HD3450), with Ati Catalyst drivers enabled and I'm using the Single display desktop (Multi-Desktop) seeting. At work I have the external monitor on the left and laptop on the right, while at home the other way around. So when I switch between the two setups, I just needed to go to Ati Catalyst Control Center, change the order of the displays, change the resolution (Home - 1680x1050, Work - 1440x900), reboot and it was all fine. But since a while it doesn't work properly anymore: At home it still works fine. At work it doesn't work. Sometimes it works for some reason, after a few resolution/setting changes in ACCC and reboots... it's very strange and annoying. With the home monitor I can see the whole bootup process on both monitors (laptop + LCD) and it always just works fine. With the work monitor on the external LCD monitor I just see "No video input" until I get to the login screen, then it shows up there as well. But after login it will either: Flicker a few times, but then work OK. Or (more often) Flicker once and then go back to "No video input" again. I usually end up rebooting a few times until it works. Does anyone have any idea for fixing it? This is my xorg.conf currently: Section "ServerLayout" Identifier "amdcccle Layout" Screen 0 "amdcccle-Screen[6]-0" 0 0 Screen "amdcccle-Screen[6]-1" 1280 0 EndSection Section "Files" EndSection Section "Module" Load "glx" EndSection Section "ServerFlags" Option "Xinerama" "off" EndSection Section "Monitor" Identifier "0-LVDS" Option "VendorName" "ATI Proprietary Driver" Option "ModelName" "Generic Autodetecting Monitor" Option "DPMS" "true" Option "PreferredMode" "1280x768" Option "TargetRefresh" "60" Option "Position" "0 0" Option "Rotate" "normal" Option "Disable" "false" EndSection Section "Monitor" Identifier "0-CRT1" Option "VendorName" "ATI Proprietary Driver" Option "ModelName" "Generic Autodetecting Monitor" Option "DPMS" "true" Option "TargetRefresh" "60" Option "Position" "0 0" Option "Rotate" "normal" Option "Disable" "false" Option "PreferredMode" "1440x900" EndSection Section "Device" Identifier "Default Device" Driver "fglrx" EndSection Section "Device" Identifier "amdcccle-Device[6]-0" Driver "fglrx" Option "Monitor-LVDS" "0-LVDS" BusID "PCI:6:0:0" EndSection Section "Device" Identifier "amdcccle-Device[6]-1" Driver "fglrx" Option "Monitor-CRT1" "0-CRT1" BusID "PCI:6:0:0" Screen 1 EndSection Section "Screen" Identifier "Default Screen" DefaultDepth 24 SubSection "Display" Virtual 2560 1024 EndSubSection EndSection Section "Screen" Identifier "amdcccle-Screen[6]-0" Device "amdcccle-Device[6]-0" DefaultDepth 24 SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection Section "Screen" Identifier "amdcccle-Screen[6]-1" Device "amdcccle-Device[6]-1" DefaultDepth 24 SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection

  Read the article

• Puppet - Possible to use software design patterns in modules?

  - by Mike Purcell

  As I work with puppet, I find myself wanting to automate more complex setups, for example vhosts for X number of websites. As my puppet manifests get more complex I find it difficult to apply the DRY (don't repeat yourself) principle. Below is a simplified snippet of what I am after, but doesn't work because puppet throws various errors depending up whether I use classes or defines. I'd like to get some feed back from some seasoned puppetmasters on how they might approach this solution. # site.pp import 'nodes' # nodes.pp node nodes_dev { $service_env = 'dev' } node nodes_prod { $service_env = 'prod' } import 'nodes/dev' import 'nodes/prod' # nodes/dev.pp node 'service1.ownij.lan' inherits nodes_dev { httpd::vhost::package::site { 'foo': } httpd::vhost::package::site { 'bar': } } # modules/vhost/package.pp class httpd::vhost::package { class manage($port) { # More complex stuff goes here like ensuring that conf paths and uris exist # As well as log files, which is I why I want to do the work once and use many notify { $service_env: } notify { $port: } } define site { case $name { 'foo': { class 'httpd::vhost::package::manage': port => 20000 } } 'bar': { class 'httpd::vhost::package::manage': port => 20001 } } } } } That code snippet gives me a Duplicate declaration: Class[Httpd::Vhost::Package::Manage] error, and if I switch the manage class to a define, and attempt to access a global or pass in a variable common to both foo and bar, I get a Duplicate declaration: Notify[dev] error. Any suggestions how I can implement the DRY principle and still get puppet to work? -- UPDATE -- I'm still having a problem trying to ensure that some of my vhosts, which may share a parent directory, are setup correctly. Something like this: node 'service1.ownij.lan' inherits nodes_dev { httpd::vhost::package::site { 'foo_sitea': } httpd::vhost::package::site { 'foo_siteb': } httpd::vhost::package::site { 'bar': } } What I need to happen is that sitea and siteb have the same parent "foo" folder. The problem I am having is when I call a define to ensure the "foo" folder exists. Below is the site define as I have it, hopefully it will make sense what I am trying to accomplish. class httpd::vhost::package { File { owner => root, group => root, mode => 0660 } define site() { $app_parts = split($name, '[_]') $app_primary = $app_parts[0] if ($app_parts[1] == '') { $tpl_path_partial_app = "${app_primary}" $app_sub = '' } else { $tpl_path_partial_app = "${app_primary}/${app_parts[1]}" $app_sub = $app_parts[1] } include httpd::vhost::log::base httpd::vhost::log::app { $name: app_primary => $app_primary, app_sub => $app_sub } } } class httpd::vhost::log { class base { $paths = [ '/tmp', '/tmp/var', '/tmp/var/log', '/tmp/var/log/httpd', "/tmp/var/log/httpd/${service_env}" ] file { $paths: ensure => directory } } define app($app_primary, $app_sub) { $paths = [ "/tmp/var/log/httpd/${service_env}/${app_primary}", "/tmp/var/log/httpd/${service_env}/${app_primary}/${app_sub}" ] file { $paths: ensure => directory } } } The include httpd::vhost::log::base works fine, because it is "included", which means it is only implemented once, even though site is called multiple times. The error I am getting is: Duplicate declaration: File[/tmp/var/log/httpd/dev/foo]. I looked into using exec, but not sure this is the correct route, surely others have had to deal with this before and any insight is appreciated as I have been grappling with this for a few weeks. Thanks.

  Read the article

• IIS URL Rewrite - Redirect any HTTPS traffic to sub-domain

  - by uniquelau

  We have an interesting hosting environment that dictates all secure traffic must travel over a specific sub domain. E.g. http://secure.domain.com/my-page I'd like to handle this switch using URL Rewrite, i.e. at server level, rather than application level. My cases are: https://secure.domain.com/page = NO CHANGE, remains the same https://domain.com/page = sub-domain inserted, https://secure.domain.com/page https://www.domain.com/page = remove 'www', insert sub-domain In my mind the logic is: INPUT = Full Url = http://www.domain.com/page If INPUT contains HTTPS Then check Full URL, does it contain 'secure'? If YES do nothing, if no add 'secure' If INPUT contains 'www' remove 'www' The certificate is not a wild card (e.g. top level domain) and is issues to: https://secure.domain.com/ The website could also be hosted in a staging environment. E.g. https://secure.environment.domain.com/ I do not have control over 'environment' or 'domain' or the 'tld'. Laurence - Update 1, 19th August So as mentioned below, the trick here is to avoid a redirect loop that could drive anyone well loopy. This is what I propose: One rule to force certain traffic to the secure domain: <rule name="Force 'Umbraco' to secure" stopProcessing="true"> <conditions logicalGrouping="MatchAll"> <add input="{REQUEST_URI}" pattern="^/umbraco/(.+)$" ignoreCase="true" /> <add input="{HTTP_HOST}" negate="true" pattern="^secure\.(.+)$" /> </conditions> <action type="Redirect" url="https://secure.{HTTP_HOST}/{R:0}" redirectType="Permanent" /> </rule> Another rule, that then removes the secure domain, expect for traffic on the secure domain. <rule name="Remove secure, expect for Umbraco" stopProcessing="true"> <match url="(.*)" ignoreCase="true" /> <conditions logicalGrouping="MatchAll"> <add input="{HTTP_HOST}" pattern="^secure\.(.+)$" /> <add input="{REQUEST_URI}" negate="true" pattern="^/umbraco/(.+)$" ignoreCase="true" /> </conditions> <!-- Set Domain to match environment --> <action type="Redirect" url="http://staging.domain.com/{R:0}" appendQueryString="true" redirectType="Permanent" /> </rule> This works for a single directory or group of files, however I've been unable to add additional logic into those two rules. For example you might have 3 folders that need to be secure, I tried adding these as Negate records, but then no redirection happens at all. Hmmm! L

  Read the article

• How can I repair my USB drive?

  - by yurko

  USB drive is in read only state and I can't repair it. First of all I tried erase it using dd: root@yurko-laptop:/home/yurko-laptop# ls -l /dev/disk/by-id | grep usb lrwxrwxrwx 1 root root 9 ??? 18 23:45 usb-Generic_Flash_Disk_C173828A-0:0 -> ../../sdb lrwxrwxrwx 1 root root 10 ??? 18 23:45 usb-Generic_Flash_Disk_C173828A-0:0-part1 -> ../../sdb1 root@yurko-laptop:/home/yurko-laptop# dd if=/dev/zero of=/dev/sdb dd: ?????? ? «/dev/sdb»: ?? ?????????? ????????? ????? 8257537+0 ??????? ??????? 8257536+0 ??????? ???????? ??????????? 4227858432 ????? (4,2 GB), 942,633 c, 4,5 MB/c After that I wanted to create new filesystem using fdisk: root@yurko-laptop:/home/yurko-laptop# fdisk /dev/sdb You will not be able to write the partition table. WARNING: DOS-compatible mode is deprecated. It's strongly recommended to switch off the mode (command 'c') and change display units to sectors (command 'u'). Command (m for help): p Disk /dev/sdb: 4227 MB, 4227858432 bytes 4 heads, 63 sectors/track, 32768 cylinders Units = cylinders of 252 * 512 = 129024 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Device Boot Start End Blocks Id System /dev/sdb1 18 32768 4126596 b W95 FAT32 Command (m for help): fdisk showed that the partition still exists and I can't write the partition table. I tried to delete the existing partition: Command (m for help): d Selected partition 1 Command (m for help): w Unable to write /dev/sdb root@yurko-laptop:/home/yurko-laptop# Why am I not be able to write the partition table? Does it mean that some hardware failure occurred? And is it possible to repair the current USB drive? I've tried to use hdparm and it showed that the readonly flag is on: root@yurko-laptop:/home/yurko-laptop# hdparm /dev/sdb /dev/sdb: SG_IO: bad/missing sense data, sb[]: f0 00 05 00 00 00 00 0a 00 00 00 00 26 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 multcount = 0 (off) readonly = 1 (on) readahead = 256 (on) geometry = 1016/131/62, sectors = 8257536, start = 0

  Read the article

• broken apache .htaccess (mod_rewrite)

  - by Tim

  Hey there, I'm running into an apache mod_rewrite configuration issue on one of our machines. Has anyone encountered / overcome anyone of these issues. URL1 ( http://www.uppereast.com ) is not being redirected to URL2 ( http://www.nyclocalliving.com ). This definitely worked in my test environment where a localhost address was rewritten to URL2 ( RewriteRule ^http://upe.localhost$ http://www.nyclocalliving.com ). I'm trying to get the all of the redirect rules working ( 2200 + ), but the 'http://www.nyclocalliving.com' site encounters a server error if I use more that 1000 or more rules. A) .htaccess file - I've tried the simplest approach which worked in a local environment 75 # Various rewrite rules. 76 <IfModule mod_rewrite.c> 77 RewriteEngine on 78 79 # BEGIN new URL Mapping rules 80 #RewriteRule ^http://www.uppereast.com/$ http://www.nyclocalliving.com ... 2307 #RewriteRule ^http://www.uppereast.com/zipcodechange.html$ http://www.nyclocalliving.com/zip-code-change fig. 1 B) /var/log/httpd/error_log file - there are these seg. fault errors when I enable the first rule ( line 80 ). no error logs otherwise. 1893 [Fri Sep 25 17:53:46 2009] [notice] Digest: generating secret for digest authentication ... 1894 [Fri Sep 25 17:53:46 2009] [notice] Digest: done 1895 [Fri Sep 25 17:53:46 2009] [notice] Apache/2.2.3 (CentOS) configured -- resuming normal operations 1896 [Fri Sep 25 17:53:47 2009] [notice] child pid 29774 exit signal Segmentation fault (11) 1897 [Fri Sep 25 17:53:47 2009] [notice] child pid 29775 exit signal Segmentation fault (11) 1898 [Fri Sep 25 17:53:47 2009] [notice] child pid 29776 exit signal Segmentation fault (11) 1899 [Fri Sep 25 17:53:47 2009] [notice] child pid 29777 exit signal Segmentation fault (11) 1900 [Fri Sep 25 17:53:47 2009] [notice] child pid 29778 exit signal Segmentation fault (11) 1901 [Fri Sep 25 17:53:47 2009] [notice] child pid 29779 exit signal Segmentation fault (11) fig. 2 C) Some more debug information from the shell; the mod_rewrite is turned on and this is the machine architecture 1 # apachectl -t -D DUMP_MODULES | more 2 Loaded Modules: 3 core_module (static) 4 ... 5 rewrite_module (shared) 1 # uname -a 2 Linux RegionalWeb 2.6.24-23-xen #1 SMP Mon Jan 26 03:09:12 UTC 2009 x86_64 x86_64 x86_64 GNU/Linux fig. 3 I looked into some previous posts (http://serverfault.com/questions/18744/htaccess-not-working-modrewrite), but didn't find a solution for this. I'm sure there's a small switch somewhere that I'm missing. Thanks in advance Tim

  Read the article

• Is there a way to permanently arrange 2 displays under XP?

  - by rumtscho

  When I am home or on a business trip, or on a meeting, I use my laptop in the usual way. When I get to work, I put it on the docking station and boot it with the lid closed. The image appears on the two displays connected to the docking station. On the left, there is an old monitor connected over VGA, on the right, a big widescreen connected over DVI. Obviously, the videocard seems to think that the DVI is the primary output, and the VGA the secondary one. Thus Windows always displays the widescreen on the left and the old FSC monitor on the right. So when I want to move the mouse pointer from the (physically) left display to the (physically) right display, I have to move it from right to left, which is a usability nightmare. Of course, I can just drag one display over the other one in the display properties, and then everything is as it should be. The catch: Windows remembers this only as long as it has the two displays. Every time it runs on the laptop display, it forgets the setting. Physically switching the monitors isn't an option, for ergonomical reasons. I prefer to run the more important applications on the bigger screen with the better colourspace, and the shape of my desk forces me to sit off-center, so the more important applications should be shown on the right display. Just switching the video ports doesn't help either. When I connect the big monitor over VGA, image quality deteriorates visibly. So what I do now is: every time I bring the laptop to my desk, I boot it. I wait the whole 7 minutes of XP booting, syncing network drives, etc. Then I fire up the display properties, switch to the last tab, drag the widescreen display to the right, and close. Only then can I start working. Does someone have a better idea? The laptop is a Dell Latitude 630 with Windows XP SP 3. It has an nVidia graphics card (not an onboard chip).

  Read the article

< Previous Page | 523 524 525 526 527 528 529 530 531 532 533 534  | Next Page >