Search Results

Search found 3680 results on 148 pages for 'dazed n confused'.

Page 53/148 | < Previous Page | 49 50 51 52 53 54 55 56 57 58 59 60  | Next Page >

• multiple vlans routed on one nic? trunk?General? or Access?

  - by Aceth

  ok for the last week I've tried racking my head around this... I have a SRW208P with 802.1q support, and a virtual endian appliance. I would like to be able to have 3 vlans having everything routed through the endian appliance.. i.e. The Virtual server has 2 bridged NIC's to the switch. This is where I'm getting confused .. On the 8 port switch I've got the 3 vlans set up ok (all being untagged as they are not going to be vlan aware), it's the port I'm connecting the endian firewall to the switch I'm having trouble with (second nic goes to the adsl modem and NAT'd) Is it meant to be a trunk, "Genereal" or "Access" then untagged or tagged? the end goal is to have vlan traffic routing through the single NIC and have endian route vlan traffic according to the rules. Any one have any ideas on the cisco small business stuff? Thanks

  Read the article

• Multiple SSL domains on the same IP address and same port?

  - by johnlai2004

  I set up an ubuntu 9.10 - apache2 - php5 server. I was under the impression that each valid SSL certificate (no domain wild cards) required it's own unique IP address and port number combination. But the answer to a previous question I posted is at odds with this claim: http://serverfault.com/questions/109766/ssl-site-not-using-the-correct-ip-in-apache-and-ubuntu Using the accepted answer, I was able to get multiple domains, each with it's own valid SSL to work on the same IP address and on port 443. I am very confused as to why the above answer works, especially after hearing from others that each SSL domain website on the same server requires its own IP+port combination. I am suspicious that I did something wrong. Can someone clear up the confusion? Websites currently using different SSL but on the same IP and Port are: https://www.yummyskin.com/ https://staging.bossystem.org/

  Read the article

• wireshark not seeing all packets on WiFi

  - by Caffeine Coma

  I'm using Wireshark on OSX, trying to sniff my home network over WiFi. While I can see packets that are sent to/from the host I'm sniffing on, I'm not seeing anything else that goes over the WiFi. It's like I'm not in promiscuous mode or something (the promiscuous mode box is in fact checked). The router is an Apple Airport Extreme, protected by WPA2. I'm attached to the network I'm trying to sniff, so I'm confused about why I can't see other traffic. Edit: I solved this by the following: Plug Macbook directly into the Airport Extreme router Enable "internet sharing" on Macbook, with no password. Bind wireless device (the one I wanted to sniff) to the WiFi hotspot generated by Internet sharing in step 2. Run Wireshark on the Macbook, bound to device en1. Don't forget to disable sharing after you're done. :-)

  Read the article

• Ping: Destination Host Unreachable, from the destination host itself

  - by phunehehe

  I have a server that responds in a weird way to ping: $ ping hostname.com PING hostname.com (<IP address>) 56(84) bytes of data. From hostname.com (<IP address>) icmp_seq=1 Destination Host Unreachable From hostname.com (<IP address>) icmp_seq=2 Destination Host Unreachable From hostname.com (<IP address>) icmp_seq=3 Destination Host Unreachable From hostname.com (<IP address>) icmp_seq=4 Destination Host Unreachable I'm confused, as the messages come from the server that I want to ping, and at the same time it's saying Destination Host (itself) Unreachable. Pinging by IP address yields the same result. The server is online and operating normally. What could be the cause?

  Read the article

• I just got a linode VPS a week ago and I've been flagged for SSH scanning...

  - by meder

  I got a 32-bit Debian VPS from http://linode.com and I really haven't done any sort of advanced configuration for securing it ( port 22; password enabled ). It seems somehow there is ssh scanning going on from my IP, I'm being flagged as this is against the TOS. I've been SSHing only from my home Comcast ISP which I run Linux on. Is this a common thing when getting a new vps? Are there any standard security configuration tips? I'm quite confused as to how my machine has been accused of this ssh scanning.

  Read the article

• Graphing services using pnp4nagios

  - by Matias

  I've managed to install pnp4nagios 0.6.3 and I'm a bit confused about how pnp4nagios generates graphics. Almost out of the box, it started graphs for ping and some http servers (not all of them). But, how can I make it graph things like disk utilization (When that value comes from SNMP)?? For example, ls /usr/local/pnp4nagios/var/perfdata/isis/ Cola_de_Mail.rrd Cola_de_Mail.xml HTTP.rrd HTTP.xml PING.rrd PING.xml Those are checks running on the host isis, but there are many other checks for that server that are not taken into account by pnp4nagios. How can I make pnp4nagios "see" the other checks?? Thanks!

  Read the article

• Mac Mail.app & Smart Mailbox conditions

  - by Michael Birchall

  Hey Guys, I'm having some trouble with my Smart Mailbox setup. I've got a Smart Mailbox named "Unread". And Contains messages that match any of the following conditions: Message is Unread Message is not in Mailbox News (AT) lovejungle.com Message is not in Mailbox Info (AT) lovejungle.com For some reasons, it is still displaying messages in either News@ or Info@. I've removed either Not in News@ or Info@ and it still shows messages from each inbox. Any ideas on what's set up wrong? :confused: http://i.imgur.com/IHquL.jpg

  Read the article

• How to choose a web server for a Python application?

  - by Phil

  Information and prerequisites: I have a project which is, at its core, a basic CRUD application. It doesn't have long running background processes which it forks at the beginning and talks to later on, nor does it have long running queries or kept alive connection requirements. It receives a request, makes some queries to the database and then responds. In order to serve static files and cachable files fast, I am going to use Varnish in all cases. Here is my question: After reading about various Python web application servers, I have seen that they all have their "fans" for certain, usually "personal" reasons, which got me confused since each usecase differs from the next. How can I learn about the core differentiating factors of Python web servers (in order) to decide how suitable they are for my project and if one would be better than the other? What are your (technically provable) thoughts on the matter? How should I choose a Python web server? Thank you.

  Read the article

• Signed and unsigned, and how bit extension works

  - by hatorade

  unsigned short s; s = 0xffff; int i = s; How does the extension work here? 2 larger order bytes are added, but I'm confused whether 1's or 0's are extended there. This is probably platform dependent so let's focus on what Unix does. Would the two bigger order bytes of the int be filled with 1's or 0's, and why? Basically, does the computer know that s is unsigned, and correctly assign 0's to the higher order bits of the int? So i is now 0x0000ffff? Or since ints are default signed in unix does it take the signed bit from s (a 1) and copy that to the higher order bytes?

  Read the article

• I want to start my portfolio site using ASP.Net and I'm a bit lost about hwo to actually put it on t

  - by Papuccino1

  I found this site: www.discountasp.net They seem cheap enough and have a track record. I decided to host my site with them. Here's where I'm confused. I host the application (my website) with them and they give me an IP address, right? Users can visit my site by typing in that IP address right? (Of course once I move the index file and create a defauly web folder, etc.) Next step is buying a domain name right? Like www.mysite.com, right? Is this the way it's done, or am I doing it wrong?

  Read the article

• Generating my own SQL Server SSL Certificate

  - by Haoest

  I hear it's possible to make myself a test certificate with MakeCert from Windows SDK, but the beast is 1.5 GB, which I feel reluctant to download for a half-megabyte program. I do, however, have IIS Resource kit with me, which has selfssl to generate certificate for IIS. Will that work for SQL Server? Is there a more convenient way of generating myself an SSL certificate for SQL Server use? I even tried using CREATE CERTIFICATE with TSQL within SQL Server and then have it BACKUP into a file, but with no success. I must have confused the concept of certificate fundamentally. Any advice?

  Read the article

• How do i enable deflate on apache2? debian

  - by acidzombie24

  I looked at the other answers and those solutions did not help. I am completely confused how to do this. I know almost nothing about apache nor how to use it and nearly all the article say write this but doesnt tell me where. So far i have done this # a2enmod deflate Module deflate already enabled Then i tried writing this in httpd.conf AddOutputFilterByType DEFLATE text/html text/plain text/xml text/css Then i wrote a longer version which involved deflate.c. After those didnt work i deleted them all and wrote the AddOutputFilterByType line in apache2/sites-enabled/000-default inside of I used this to test http://www.whatsmyip.org/http_compression/ everytime it says no compression. I used another site but i could never compress. Also i restart the server everytime i save a file so what could be the problem and how do i enable this properly?

  Read the article

• What Windows licenses are required to run additional terminal service sessions

  - by John P

  We need to build out a server running Windows 2008 R2 Standard that can allow up to 10 simultaneous RDP/Terminal Services connections and I'm a little confused about how the CAL licenses work. From one source I was told I needed 10 "server CALs" and an additional 10 "RDP CALs" (total of 20 CALs). From another, I was told I just needed the 10 "RDP CALs", which implicitly came with the server CAL. The Microsoft licensing website (http://www.microsoft.com/windowsserver2008/en/us/licensing-rds.aspx) seems to support scenario #1, but it is still not real clear what those server CALs are needed for. Also, can we use the 2 "built-in" RDP clients, meaning we only need to purchase 8 CALs to reach a total of 10?

  Read the article

• verisign certificate into jboss server SSL

  - by rfders

  i'm trying to enable jboss to uses ssl protocol using a previously generated certificate from verisign, i imported both certificate, server certificate and ca certificate into the keytore file, and i configured the server.xml to use that keystore and activate ssl protocol, then when i run the jboss, I got this error "certificate or key corresponds to the SSL cipher suites which are enabled" Question, reading some post on internet, i found that every example was made it generating a Certificate Request, it stricly necesary to do that if i already have the server certificate and that CSR has to be imported into the keystore as well ? at this point i'm very confused about this issue, i tried almost every solutions posted in several forums but till now i haven't any luck !! can you give me some tips in order to solve this problem. thanks in advance this are my keystore file: Keystore type: jks Keystore provider: SUN Your keystore contains 2 entries j2ee, Dec 29, 2009, trustedCertEntry, Certificate fingerprint (MD5): 69:CC:2D:2A:2D:EF:C4:DB:A2:26:35:57:06:29:7D:4C ugent, Dec 29, 2009, trustedCertEntry, Certificate fingerprint (MD5): AC:D8:0E:A2:7B:B7:2C:E7:00:DC:22:72:4A:5F:1E:92 and my server.xml configuration:

  Read the article

• Problem with SVN filename encoding on Mac OS X

  - by Albert

  I have some filename with some Unicode character in it. All filenames on Mac OS X are UTF8 encoded. Also $LANG is set to en_US.UTF-8. However, it seems svn has some problems with that: az@ip212 1054 (Integration) %ls Abbildungen Verbesserungsvorschläge_Applets.odt AllgemeineAnmerkungen.rtf Verbesserungsvorschläge_Applets.rtf Geogebra Vorlagen Texte az@ip212 1055 (Integration) %svn ls Abbildungen/ AllgemeineAnmerkungen.rtf Geogebra/ Texte/ Verbesserungsvorschläge_Applets.rtf Verbesserungsvorschläge_Applets.odt Vorlagen/ az@ip212 1056 (Integration) %svn del Verb*.odt svn: Use --force to override this restriction svn: 'Verbesserungsvorschläge_Applets.odt' is not under version control az@ip212 1057 (Integration) %svn status ? Verbesserungsvorschläge_Applets.odt ! Verbesserungsvorschläge_Applets.odt az@ip212 1058 (Integration) % As you can see, svn del does not recognize the filename. And even svn status gets confused about it. How can I fix this? I also tried with LC_CTYPE=$LANG LC_ALL=$LANG LC=$LANG but no change.

  Read the article

• why do Vagrant docs suggest using public IP address 33.33.33.10 for local VMs?

  - by Gert

  I'm following a tutorial to set up vagrant (a tool to build and configure portable virtual machine images), and it seems that vagrant documentation suggests using IPv4 address 33.33.33.10 to configure a new box. That is a publicly routed IP adress, so I'm a bit confused why using this address is suggested. Since I don't own this network, I should not use an address from the 33.33.33.10/8 range. Am I correct in thinking that I should only use either a public address from a network I own, or an address from one of the private ranges as defined in RFC 1918? If so, why does Vagrant documentation suggest otherwise?

  Read the article

• Radeon hd 6570 black screen

  - by Sho

  I got some problem with new graphic card. Every time I use AMD Catalyst drivers on Windows or Linux, screen repeatedly goes black. This usually shows u when i open new cards in a browser, resize a window or run a program. Card runs smoothly on basic drivers but this means low resolution. 1940x1080 is native for my monitor so it causes a lot of problems. I've got a 600W Deus G1, so the power is not the problem. Maybe its a silly question, but would going form a vga cable to hdmi help to improve this situation? If not, can it be caused by slow processor or old mainboard? Im getting kinda confused about this whole thing...

  Read the article

• Can a MySQL slave be a master at the same time?

  - by mmattax

  I am in the process of migrating 2 DB servers (Master & Slave) to two new DB Servers (Master and Slave) DB1 - Master (production) DB2 - Slave (production) DB3 - New Master DB4 - New Slave Currently I have the replication set up as: DB1 -> DB2 DB3 -> DB4 To get the production data replicated to the new servers, I'd like to get it "daisy chained" so that it looks like this: DB1 -> DB2 -> DB3 -> DB4 Is this possible? When I run show master status; on DB2 (the production slave) the binlog possition never seems to change: +------------------+----------+--------------+------------------+ | File | Position | Binlog_Do_DB | Binlog_Ignore_DB | +------------------+----------+--------------+------------------+ | mysql-bin.000020 | 98 | | | +------------------+----------+--------------+------------------+ I'm a bit confused as to why the binlog position is not changing on DB2, Ideally it will be the master to DB3.

  Read the article

• x86 exceptions and flags

  - by b-gen-jack-o-neill

  Hi, please, I know that when you for example divide by zero, the aproptiate flag is set in CPU flag register. But today I read that there are special interrupt vectors (I think the first 16 in IVT) that are used for such conditions like dividing by zero. So, what I want to ask is, does any situation that couses change som flag also triggers apropriate interrupt? Becouse in school, we used conditional jumps that checks wheather carry flag has been set or not, and I don´t remember there was some interrupt triggerd by that. So I am pretty confused now.

  Read the article

• Help getting iPython to run from the OSX terminal.

  - by Azfar

  Hi there, Got a heads up from stackoverflow.com to ask the question here. I'm going through the matplotlib documentation and prepared to use the iPython interactive Python shell with ipython -pylab. However I get this: MBP:~ Me$ ipython -pylab -bash: ipython: command not found Did I fail to install iPython? I used easy_install as advised. Any ideas? Update Thought I'd just say that I found the iPython "executable" in /opt/local/Library/Frameworks/Python.framework/Versions/2.6/bin after doing a Spotlight search. Still a little confused as to what to do.

  Read the article

• Why didn't cable select work?

  - by jldugger

  I got roped into doing tech support for a friend of the family. Obviously I'd already failed to hide my powers, ala Penny Arcade. Anyways, the guy bought a DVD burner OEM from Microcenter, and asked me to install it. So I stopped by before and thought I'd be slick and use Cable Select on the jumpers. I didn't get a chance to test it before it I had to leave, and it seems that this didn't work. I came back this week to investigate, and he explains he's confused how none of the software he downloaded was able to burn. So on a whim I switch it to explicit master / slave, and it starts working fine. Whoops. Well, at least it's not the extra crap he found and downloaded for free from the internet. Why doesn't setting both jumpers to Cable Select solve this?

  Read the article

• VMWARE V2V migration without shared storage

  - by TheCleaner

  I would like to do the following: Take Physical box running w2k8r2 and Sql2008R2 and do a P2V on it to a 4.1 Enterprise licensed cluster. --no worries here, I can do that part-- Take the existing physical box that is freed up and install vmware hypervisor 5.0 on it. --again I can do this part-- Do a v2v migration of the VM created in step #1 above from the Enterprise 4.1 Cluster to the standalone host. They are NOT using shared storage. Step #3 is where I'm confused as to what my best option is. I found an article online talking about using Veeam FastSCP and just shutting down the vm on the cluster, removing it from inventory, copying the files over to the new host and then adding it to inventory. Is that the best way to accomplish this?

  Read the article

• How are my DNS entries safe in a shared hosting environment?

  - by Jake

  I'm trying to understand how DNS works in a shared hosting environment. I went to my registrar and set my name servers to my host's ns1.foo.com and ns2.foo.com. I'm using a cloud hosting provider who has a web portal where I can set my DNS entries. However I am confused by the lack of security. when I entered in the entries for my domain there was never any step to prove that I actually own that domain. What is to stop somebody else on the same hosting service (a nasty neighbor) from writing over my DNS entries and pointing my traffic to their server instead?

  Read the article

• Windows cmd does not recognize xx.exe even though xx.exe is in system path

  - by July

  I installed 7-zip and add its directory to system path: C:\Program Files\7-Zip to PATH, from windows start-input cmd and press enter, Windows command line is started, i type 7z.exe, then press enter, it just run. However when i start command line this way: cmd.exe /c start {projectDir} /D{driveLetter} cmd /K then i type 7z.exe, it gives me error because it can not find 7z.exe. why and how to fix? P.S. 1. I'm on Win7. 2. For some other apps, the above way did works, that's why i'm so confused how bat works.

  Read the article

• Trouble with resolving hostnames on CentOS using Bind

  - by cabaret

  I'm taking a course on server administration at school and I have managed to set up virtual hosting in apache and a dns server on a virtual machine. However, I have now set up an old pc to run CentOS and I'm trying the same on that box. The problem I ran into now is that I can't resolve hostnames from the linux box. I have set up the nameserver in /etc/resolv.conf to the IP of the CentOS machine, but when I try for example ping google.com I get ping: unknown host google.com However, when I do ping 66.102.13.105 (which is the Google IP, figured that out by pinging on my mac) I get: PING 66.102.13.105 (66.102.13.105) 56(84) bytes of data. 64 bytes from 66.102.13.105: icmp_seq=1 ttl=52 time=15.5 ms Slightly confused why this is happening. Could it be because of my router sitting in between the linux machine and the cable modem? It's a D-Link somethingsomething. Thanks in advance

  Read the article

< Previous Page | 49 50 51 52 53 54 55 56 57 58 59 60  | Next Page >