Search Results

Search found 18677 results on 748 pages for 'current'.

Page 531/748 | < Previous Page | 527 528 529 530 531 532 533 534 535 536 537 538  | Next Page >

• Computer hangs at boot screen with new RAID card

  - by shanethehat

  I am trying to build a new server around a Biostar TH61 motherboard and an Adaptec 6405E RAID controller card. The machine booted fine from USB before the RAID card and drives were installed. After installing, on the first boot the card was detected, but then started to spit out the following message every 10 seconds: Error: Controller Kernel Stopped Running << Press any key to continue ... Following the troubleshooting guide I unplugged everything, reseated the card, and reattached all the drives. This time the machine is sitting on the boot screen without any error messages and flashing a cursor, but after 15 minutes of this, nothing seems to be happening. Given that there are no error messages I'm hesitant to reboot again. Is it normal for a RAID card to sit without a status message when it firsts boots, maybe to initialise the drives or something? The current screen output looks a bit like this: Controller #00 found at PCI Slot:01, Bus:01, Dev:00, Func:00 Controller Model: Adaptec 6405E Firmware Version: 5.2-0[18512] Memory Size: 128MB Serial number: 111111111111111 SAS WWN: 50000D1104AE9180 _ Update: So after waiting 30 minutes I've rebooted back to the Kernal Stopped Running error. Maybe time to update the RAID BIOS.

  Read the article

• DAS vs SAN storage for serving 2 to 4 nodes

  - by Luke404

  We currently have 4 Linux nodes with local storage, arranged in two active/passive pairs with storage mirrored using DRBD, running virtual machines (actually using Xen Hypervisor) for typical hosting workloads (mail, web, a couple VPS, etc.). We're approaching the (presumed) maximum IOPS of those servers, and we're planning to migrate to an external storage solution with two active nodes, with capacity for up to four active nodes. Since we're an all-Dell shop I've done some research and found the MD3200 / MD3200i products should be the ones we're looking for. We are pretty sure we won't be attaching more than 4 hosts on a single storage and I'm wondering if there is any clear advantage for one or the other. In theory I should be able to attach 4 SAS hosts to a single MD3200 (single links on a single controller MD3200, or dual redundant SAS links from each host to a dual-controller MD3200), or 4 iSCSI hosts to a single MD3200i (directly on its 4 GigE ports without any switch, again with dual links for the dual controller option). Both setups should let us implement live VM migration since all hosts can access all the LUNs at the same time, and also some shared filesystem like GFS2 or OCFS2. Also, both setups should allow full redundancy of the whole system (assuming dual controllers in the storage). One difference I can see is that the DAS solution is actually limited to 4 hosts while the iSCSI one should be able to grow to more hosts (adding two GigE switches to the mix). One point for the iSCSI solution is that it would allow us to start out with our current nodes and upgrade them at a later time (we can't add other SAS controllers, but they already have 4 GigE ports each). With the right (iSCSI|SAS) controllers I should be able to connect diskless nodes and boot them off the external storage which I think is a good thing (get rid of any local storage). On the other hand, I would have thought the SAS one to be cheaper but it seems like an MD3200 actually costs a little less than an MD3200i (?) (please note: I've used Dell gear in my examples since that's what we're looking for but I assume the same goes with other vendors) I would like to know if my assumptions above are correct, and if I'm missing any important difference between the two setups.

  Read the article

• Move an SSD with Windows 7 to a new PCIe SATA controller card

  - by Shevek

  This is my current setup: Abit AB9 QuadGT motherboard which has an Intel P965 chipset with Intel ICH8 SATA Rev. 2.0 controller Kingston HyperX 3K 120GB SSD which supports SATA Rev. 3.0 Windows 7 Ultimate x64 For some reason I was unable to install Windows with the controller set in AHCI mode, even with the correct driver from Intel so it is currently in IDE mode. Due to the ICH8 controller being SATA Rev 2.0 and running in IDE mode, the SSD is operating well under it's published read/write speeds. I have ordered an Asus U3S6 controller card to add both SATA Rev. 3.0 and USB 3.0 to my computer. The motherboard does have a PCIe x4 slot available so I will hopefully achieve the full potential of my SSD. My question is this - am I able to swap the SSD over to the controller card from the motherboard controller without having to clean install Windows? I am hoping that all I will need to do is ensure that the controller card drivers are available to Windows and set the registry as per this KB article. Will this work or should I perform a clean installation?

  Read the article

• Port Forwarding failing only to Ubuntu servers from Draytek router

  - by Rufinus

  I know this is a kinda unusal question, but Draytek support (..which is very eager to solve the issue) seems to reach its limits. Scenario: Draytek Vigor Multiwan router with current firmware. Multiple WAN IP Aliases on one of the wan ports DMZ (or port forwarding doesnt matter) from wan ip alias to internal host currently i have two internal hosts: 192.168.0.51 (Ubuntu) 192.168.0.53 (Debian) both should be accessible from outside via one of the wan ip aliases. both are accessible with their internal ip's at all times (!) If the router gots restartet, both external ips are forwarding to its internal hosts. But after a few minutes up to 2 hours, the ubuntu host is no longer reachable via its external interface. The debian hosts on the other hand is reachable. In what does ubuntu differs from debian ? I know at least of one user with the exact same problem. see http://ubuntuforums.org/showthread.php?p=10994279 Any ideas ? TIA EDIT: via ping diagnostics directly on vigor, 192.168.0.53 is pingable, 192.168.0.51 is not. but both hosts are perfectly reachable from anywhere inside the network. if i restart ubuntu networking it works again for a short time.... i'm out of ideas.. EDIT 2: after further investigation, i noticed a ping from .51 to the network (or a host in the internet) is enough to make the port-forwarding working again. So i will add an Cronjob as a "keep-alive" ping. This will solve the problem, but the reason for this behaivor is still in the dark. Thanks to all commentors.

  Read the article

• Home Server: cpu virtualisation, what to choose?

  - by Huygens

  I'm looking for virtualisation solutions for storage and OS for a home server. A sort of private cloud where I manage the storage space independently of the VM one. This question focus on VM (or compute instance) management and what would best suit my needs. (I have another question related to the storage management). My use cases are: A backup server: rsync and other services running. A personal cloud server: a kind of owned dropbox system, à la ownCloud. " users foreseen. A media server: streaming videos and displaying photos. Here my environement and wishes: Server: HP Proliant MicroServer with 8 GB RAM (AMD Turion dual core with AMD-V technology) OS types: only Linux (perhaps a *BSD VM in the future) Linux distributions do not matter, I'm familiar with RHEL, Fedora, Suse, Ubuntu, but any other recommandation will be fine 2-3 VMs foreseen: backup server, owncloud server and media server (optional). Those are only servers, so no graphical console needed (I don't need VirtualBox) By VM I mean a virtualised environment like KVM, Xen, etc. or a compute instance like with OpenStack storage should be "virtualised/cloudified" see my other question. VM should be able to be migrated to another server in the future if performance cannot be fullfilled anymore by the current server It does not matter if installation of such setup is complicated as long as management tools allow for easy maintenance I don't have Windows at home, so solution should be Linux friendly and would be nice to be web based. But native apps are OK too. System should be easy to enhance: by adding a new server to migate some of the VMs to it. So it's really a kind of private cloud on which I could run some Linux OS. I would prefer free (libre, as in a free speach) and open source tools. But it does not have to be free as in a free beer. So Xen, KVM, VitualBox or OpenStack? What would you recommend?

  Read the article

• How to troubleshoot when one has no idea where to start?

  - by Chris Walton

  I am looking for hints, tips and answers on how to get started on troubleshooting when: The problem is intermittent The problem could lie literally anywhere - operating system; free source software; my own software developments; purchased software; crumbs on the keyboard; the specific combination of software I am currently running; Maxwell's demon; the little blue men actually running the machine have gone on strike; etc. I have expertise only in a few of the areas that are potential candidates for the cause of the problem. The specific problem I am having is detailed below as an example, but I am not seeking answers to my current problem, but rather where and how to start on tackling such problems. I am currently encountering a problem with my new machine. On a few occasions the machine has just frozen; not accepting keystrokes, mouseclicks, or anything except the power on/off switch. Invariably I have been merely browsing the web; I have had a few (<= 6 other applications) running. None of these applications are major; and represent a mix of commercial programs and open source programs, typically migrated from Unix of some variety. My machine is a Windows 7 I7 quad core laptop.

  Read the article

• SSD Drive not being recongized in BIOS

  - by chobo2

  Well I bought my first drive Mushkin Chronos 180GB and got it installed in my computer and loaded up. I went to windows 7 and initialized the drive and then I installed "SSDlife Free" and loaded it up and my the SSD drive came up said it was "powered on 3 times"(thought it was odd but then thought maybe some testing???). I then restarted my computer and loaded into Acronis. Went to my SSD drive and make a partition called windows(made a basic logical partition). I then loaded up Norton ghost and wanted to copy my current windows onto the SSD drive on the partition I made found out I could not do it through the recovery disk so I made a backup of my windows drive and wanted to then restore it onto the SSD drive. Came back an hour later when the backup was done. I tried to restore the it on my SSD drive and could not find the partition so I loaded up Acronis again and it did not see it. I then went to the bios and saw only my other hard drive. What I tried Tried uplugging and replugging in both sata and power cables. Tried using the power and sata cable from the working drive and giving it the ones that SSD drive were using. Tried Sata AHCI Mode (Intel ICH9 Southbridge) Tried SATA PORT0-1 NATIVE MODE (Intel ICH9 Southbridge) Nothing worked. Software / hardware Windows 7 ultimate Gigabyte S-Series GA-P35-DS3L Mother board I hope someone has some ideas on why it is not being recognized.

  Read the article

• ADFS Relying Party

  - by user49607

  I'm trying to set up an Active Directory Federation Service Relying Party and I get the following error. I've tried modifying the page to allow <pages validateRequest="false"> to web.config and it doesn't make a difference. Can someone help me out? Server Error in '/test' Application. A potentially dangerous Request.Form value was detected from the client (wresult="<t:RequestSecurityTo..."). Description: Request Validation has detected a potentially dangerous client input value, and processing of the request has been aborted. This value may indicate an attempt to compromise the security of your application, such as a cross-site scripting attack. To allow pages to override application request validation settings, set the requestValidationMode attribute in the httpRuntime configuration section to requestValidationMode="2.0". Example: <httpRuntime requestValidationMode="2.0" />. After setting this value, you can then disable request validation by setting validateRequest="false" in the Page directive or in the <pages> configuration section. However, it is strongly recommended that your application explicitly check all inputs in this case. For more information, see http://go.microsoft.com/fwlink/?LinkId=153133. Exception Details: System.Web.HttpRequestValidationException: A potentially dangerous Request.Form value was detected from the client (wresult="<t:RequestSecurityTo..."). Source Error: An unhandled exception was generated during the execution of the current web request. Information regarding the origin and location of the exception can be identified using the exception stack trace below. Stack Trace: [HttpRequestValidationException (0x80004005): A potentially dangerous Request.Form value was detected from the client (wresult="<t:RequestSecurityTo...").] System.Web.HttpRequest.ValidateString(String value, String collectionKey, RequestValidationSource requestCollection) +11309476 System.Web.HttpRequest.ValidateNameValueCollection(NameValueCollection nvc, RequestValidationSource requestCollection) +82 System.Web.HttpRequest.get_Form() +186 Microsoft.IdentityModel.Web.WSFederationAuthenticationModule.IsSignInResponse(HttpRequest request) +26 Microsoft.IdentityModel.Web.WSFederationAuthenticationModule.CanReadSignInResponse(HttpRequest request, Boolean onPage) +145 Microsoft.IdentityModel.Web.WSFederationAuthenticationModule.OnAuthenticateRequest(Object sender, EventArgs args) +108 System.Web.SyncEventExecutionStep.System.Web.HttpApplication.IExecutionStep.Execute() +80 System.Web.HttpApplication.ExecuteStep(IExecutionStep step, Boolean& completedSynchronously) +266 `

  Read the article

• Turn off monitor (energy saving) while in text console mode (in Linux)

  - by Denilson Sá

  How to configure Linux text console to automatically turn of the monitor after some time? And by "text console" I mean that thing that you get on ctrl+alt+F[1-6], which is what you get whenever X11 is not running. And, no, I'm not using any framebuffer console (it's a plain, good and old 80x25 text-mode). Many years ago, I was using Slackware Linux, and it used to boot up in text-mode. Then you would manually run startx after the login. Anyway, the main login "screen" was the plain text-mode console, and I remember that the monitor used to turn off (energy saving mode, indicated by a blinking LED) after some time. Now I'm using Gentoo, and I have a similar setup. The machine boots up in text-mode, and only rarely I need to run startx. I say this because this is mostly my personal Linux server, and there is no need to keep X11 running all the time. (which means: I don't want to use GDM/KDM or any other graphical login screen) But now, in this Gentoo text-mode console, the screen goes black after a while, but the monitor does not enter any energy-saving mode (the LED is always lit). Yes, I've waited long enough to verify this. Thus, my question is: how can I configure my current system to behave like the old one? In other words, how to make the text console trigger energy-saving mode of the monitor? (maybe I should (cross-)post this question to http://unix.stackexchange.com/ )

  Read the article

• FTP not listing directory NcFTP PASV

  - by Jacob Talbot

  I am attempting to setup Multicraft on my server, all is running smoothly however the FTP won't allow anyone to connect from a remote FTP client, where net2ftp will work smoothly from a remote location. I have included the transcript from my FTP client, Transmit below to give you an idea of what's going on. I have disabled iptables as well, and still no luck either way. Transmit 4.1.7 (x86_64) Session Transcript [Version 10.8.2 (Build 12C54)] (21/10/12 11:23 PM) LibNcFTP 3.2.3 (July 23, 2009) compiled for UNIX 220: Multicraft 1.7.1 FTP server Connected to ateam.bn-mc.net. Cmd: USER jacob.9 331: Username ok, send password. Cmd: PASS xxxxxxxx 230: Login successful Cmd: TYPE A 200: Type set to: ASCII. Logged in to ateam.bn-mc.net as jacob.9. Cmd: SYST 215: UNIX Type: L8 Cmd: FEAT 211: Features supported: EPRT EPSV MDTM MLSD MLST type*;perm*;size*;modify*;unique*;unix.mode;unix.uid;unix.gid; REST STREAM SIZE TVFS UTF8 End FEAT. Cmd: OPTS UTF8 ON 200: OK Cmd: PWD 257: "/" is the current directory. Cmd: PASV Could not read reply from control connection -- timed out. (SReadline 1)

  Read the article

• OpenVPN Server - CPU is pegged out

  - by ericl42

  Hello, I am configuring OpenVPN to act as a SSL tunnel for a remote location. I have OpenVPN1 at our current location acting as a server then OpenVPN2 at the other location that is acting as a client but is also acting as a DHCP server to machines behind it so they are basically connected to the local LAN. Everything is set up fine and I can talk from location A to location B with no problems like everyone is local. I am however having some performance issues. OpenVPN1 CPU is pegged to 100% the entire time I am copying or doing any type of activity through the tunnel. I expect some CPU usage going up but nothing like this. It's really killing my performance. OpenVPN1 is running in ESX right now with 2 gig RAM and 4 procs with unlimited bursting capacity. I am using AES-192 encryption with a 1024 key. Any idea how I can get my CPU down on OpenVPN1 and my download/upload speeds higher between the tunnel? Thanks. edit: Turning down the logging helped boost the throughput a little bit, but I am still fairly shy of where I believe I should be. Also I am still maxed out on the CPU. Does anyone have any ideas? I am really stuck on this. Thanks.

  Read the article

• What do the readonly attributes in diskpart really mean?

  - by marzipan

  I am wondering exactly what the meaning is of the "Read-only" disk and volume attributes that you can twiddle in diskpart on Windows 7. I am trying to set up an external USB drive as an installation medium for my own software, so I'd like to protect it against casual or inadvertent changes by users who it is given to, so they don't screw up the installation files they might need in the future. From what I can tell by experimentation with diskpart, the volume read-only attribute is actually stored on the physical disk somewhere, because I can set it and it shows up when I take the drive to another machine. This is great because my users can't (easily) change any of the files on the volume, or format it from Windows explorer. However, the disk read-only attribute seems to be just an aspect of how the current machine is accessing the drive. When I set it I can no longer delete the volume in the disk via Disk Management, but when I take the drive to another machine, the attribute is no longer set and in Disk Management I can delete the volume on the disk. I guess I'm not that worried about my users doing that, but I am annoyed that I don't understand what these attributes are really doing. Another thing that I don't understand is that the "volume" read-only attribute actually seems to be global to the disk - if I have two volumes on the disk, and I set the readonly flag on one of them, then it gets set on the other one too. ?!? I have the feeling I'm not searching for the right docs - all I'm finding is diskpart docs that give the syntax for twiddling these attributes, not what they really mean. Any pointers would be very welcome! Thanks, Asa

  Read the article

• Some guest networking and VMware Tools functionality broken with Sprint SmartView on the host

  - by Mads

  Using VMware Workstation 6.5.3 on Vista 64-bit. I started having problems with VMware networking about 6 months ago after upgrades to Sprint SmartView. I did not have problems previously, but I don't know if that is because I was lucky. The main symptoms of the problem when SmartView is installed are: I can no longer drag files from the host to copy them to the guest. When they are dragged, the disallowed cursor (the circle with a slash) shows in the guest. If I try to enable shared folders in the guest while it is running, I will not be able to see the shared files and will be informed that networking is not working. I can still ping guests from the host and I can still access network services via NAT most of the time when connected via my USB broadband adapter. When I configure shared folders so they are "always enabled" (with a mapped drive), I can access files on the via the mapped folders. I can also copy the file on the host and then paste it in the guest, as was suggested in some other threads concerning drag-and-drop problems that I found. The VMware Tools icon is showing in all cases and I don't see any obvious errors in the host's event viewer. If I uninstall SmartView, the problems disappear. If SmartView (current version is 2.28.0082) is reinstalled I will experience the same problems. I have tried uninstalling/reinstalling VMware and SmartView in various ways but it appears tha these problems are consistent when SmartView is installed (not just when it is running or connected, but when it is present on the system). I'm wondering if this is a combination of software (WS 6.5.3, Vista64, and SmartView) that works for other people, which would indicate a problem that is peculiar to my configuration.

  Read the article

• Excel concatenate strings from cells listed in third cell

  - by Puddingfox

  I have an excel 2007 workbook that has five columns: A. A list of machines B. A list of service numbers for each machine C. A list of service names for each machine ...(nothing here) I. A list of Service Numbers J. A list of Service Names Each machine listed in column A has one or more services running on it from the list in column J. I would like to be able to add services to a machine (i.e. updating the cell in Column C) by simply adding another comma-separated number to Column B. For Example, The first row would look like this assuming Machine1 has the first three services: | A | B | C | Machine1 | 1,2,3 | HTTP,HTTPS,DNS Right now I have to manually update the formula in column c for each change I make. The current formula is: =CONCATENATE(J1,",",J2,",",J3) I would like to use something like this (please forgive my syntax; I'm a coder and I'm treating cell B1 as if it is an indexed array): =CONCATENATE(CELL("J"+B1[0] , "," , "J"+B1[1] , "," "J"+B1[2]) Although having variable numbers of services makes this even more difficult. Is there any way of doing this. For reference, this is columns I and J: | I | J | 1 |HTTP | 2 |HTTPS | 3 |DNS ..... | 16 |Service16 I don't know very much about Excel so any help is greatly appreciated.

  Read the article

• IPv6 - Public IPs, private IPs, IPs derived from the MAC address? Confused!

  - by sinni800

  I'm pretty much excited for IPv6 because of the large address room and (potential?) owning of more than one IP, or even tens of IPs (/122 subnet?) Though one magazine has now confused me. In a current issue (no. 3) of "CT", a German computer magazine, I read that when using IPv6 your IP address consists of your MAC address and various other things, and that this address will be public on the web, no matter what access point / LAN you connect to. My knowledge of IP(v6) is in contrary of this. I thought you will normally always have a a local network IP and NAT takes care of your Internet access, and your provider gives the NAT router an IP. I've heard of the 6to4 interface, but does this one give you your own ip in the IPv6 net? Personally I hope it still is through a personal IP space (like 192.168, 127.16-31, 10. in IPv4) in private networks with a NAT going to the Internet. And also I hope that providers will offer subnets to private customers so they don't have to use NAT anymore. Yay for converting your LAN into the WAN and using better security (so Computers from the same subnet still get access rights like normal).

  Read the article

• Cluster FIle System

  - by Ben

  We are looking for to choose a clustered file system for our in house appplication. Let me first highlight my requirement. we have a storage and 2 servers at present.We get the data files from remote servers to our server and on both servers we are running our application to access those data and make a final result as per our requirements. In future may be after 3-4 months, we can add another servers in current cluster pool to handle more data load from remote location data senders. So my requirement is that to integrate same storage partition on 2-3 servers , it might be 4-5 more servers in future, My application read data from storage partition and write back to storage partition. Is there any bottleneck / limitation from RHCS , GFS2 or anything.? We are new with RHCS + GFS and all. Can we have any other better approach or someway to deal with our requirement light way? what is the best OS version for this ? how's RHEL 6.4 64 bit ? please share some case study or some gudie reference as per past experiences with such environnmnets Regards, Ben

  Read the article

• nginx projects in subfolders

  - by Timothy

  I'm getting frustrated with my nginx configuration and so I'm asking for help in writing my config file to serve multiple projects from sub-directories in the same root. This isn't virtual hosting as they are all using the same host value. Perhaps an example will clarify my attempt: request 192.168.1.1/ should serve index.php from /var/www/public/ request 192.168.1.1/wiki/ should serve index.php from /var/www/wiki/public/ request 192.168.1.1/blog/ should serve index.php from /var/www/blog/public/ These projects are using PHP and use fastcgi. My current configuration is very minimal. server { listen 80 default; server_name localhost; access_log /var/log/nginx/localhost.access.log; root /var/www; index index.php index.html; location ~ \.php$ { fastcgi_pass 127.0.0.1:9000; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME /var/www$fastcgi_script_name; include fastcgi_params; } } I've tried various things with alias and rewrite but was not able to get things set correctly for fastcgi. It seems there should be a more eloquent way than writing location blocks and duplicating root, index, SCRIPT_FILENAME, etc. Any pointers to get me headed in the right direction are appreciated.

  Read the article

• Thundrbird 3: can't change column width?

  - by rumtscho

  I recently installed Thunderbird 3.0.3. Just noticed a suboptimal UI setting: in the upper pane, which lists the e-mails in the current folder, the Date column is about 200px wide. So when I keep the window at 480x600, all I see in a row is: | tree icon | favourites icon | attachment icon | read icon | junk icon | Date and time, followed by 5cm whitespace | ... | P Where "P" is the first letter of the name of the sender. And the "..." is actually shown this way, I have no idea which column it is meant to be. But I don't see neither the sender, nor the message subject, which makes scrolling a folder for a certain mail rather pointless. I see these when I maximize the window, actually the columns are then not only bigger, they are arranged in another sequence. But I feel that holding a mail client permanently maximised at 1600x1200 is a waste of screen real estate. My naive solution attempt was to try to go with the mouse cursor to the right edge of the date column and try to shrink it by moving the cursor left while holding down the left mouse button. Not only is this default behaviour for all resizable columns I've ever encountered in GUIs, the cursor actually turns into a horizontal double-headed arrow. But pulling has no effect at all. I cannot make a wide column narrow, and I cannot make the narrow columns wide. I didn't find anything in the preferences either. So can please somebody explain how to get the columns arranged sensibly?

  Read the article

• Managing disk in a VM

  - by dst

  I'm replacing my two old rack servers with a new one that has plenty of power to take over the functionality my current servers. The server is a 4U rack mount with 16 3.5" SAS drive bays, two 2.5" bays, a Xeon E3-1230v2 CPU and 32GB of ECC RAM. My issue is the following. I would like to have a FreeBSD file server with ZFS managing disks. However, I need other VMs for e.g. a shell/git server, mail server etc. I'm wondering how to deal with the following issues: I want ZFS to fully manage the disks, so I'm not using any hardware RAID. Should I pass the SAS controller directly to the FreeBSD system as passthrough PCI? I want to maximize the reliability of the setup. On what disks should I install the hypervsor and keep server system disks? For (2) I have the option of having a RAID setup on the SAS controller and using that as system disk to store the hypervisor as well as VM images. However, this makes PCI passthrough to the file server impossible. Another option is using the two 2.5" bays. In terms of reliability how are SSDs compared to e.g. WD RE4 disks? Would it make sense to have two SSDs in software RAID as boot disks for the hypervisor or should I just go with e.g. WD RE4 disks in a software RAID setup. I also need to think about where to store the mails for the mail server, but this could be done over NFS between the VMs. BTW, this is for home use, so the load is not really that big. What I'm looking for is best practices for splitting up a server.

  Read the article

• Moving a lotus database causes incoming mail failure

  - by Logman

  Hey all, I moved a couple lotus note databases to another hd (ran out of space) by using a directory link/pointer on the domino server. USed a text file with the .DIR ext with the desired new path etc... well that works fine. I open up a lotus notes client, use the id and then OPEN the database. The directory link works fine, the new location of the db is opened with no problems. We found out that we couldnt FORWARD any mail: We did the following to make it work: Goto menu FILE|MOBILE|EDIT CURRENT LOCATION Goto tab MAIL and enter the correct path for "Mail File:" example: it should read "mail\morespace\flabor" and not "mail\flabor" "morespace" = directory link/pointer we can forward and reply to emails fine after that fix. The problem is that the user has no incoming email. Domino is still trying to send the incoming mail of that user to its old db location "mail\flabor" instead of "mail\morespace\flabor". Delivery error saying user does not exist. Is this a cache problem? We have reset the server ("Q" at the prompt), though we have not completely shut it down though. Thanks Frank

  Read the article

• Why does redis report limit of 1024 files even after update to limits.conf?

  - by esilver

  I see this error at the top of my redis.log file: Current maximum open files is 1024. maxclients has been reduced to 4064 to compensate for low ulimit. I have followed these steps to the letter (and rebooted): Moreover, I see this when I run ulimit: ubuntu@ip-XX-XXX-XXX-XXX:~$ ulimit -n 65535 Is this error specious? If not, what other steps do I need to perform? I am running redis 2.8.13 (tip of the tree) on Ubuntu LTS 14.04.1 (again, tip of the tree). Here is the user info: ubuntu@ip-XX-XXX-XXX-XXX:~$ ps aux | grep redis root 1027 0.0 0.0 66328 2112 ? Ss 20:30 0:00 sudo -u ubuntu /usr/local/bin/redis-server /etc/redis/redis.conf ubuntu 1107 19.2 48.8 7629152 7531552 ? Sl 20:30 2:21 /usr/local/bin/redis-server *:6379 The server is therefore running as ubuntu. Here are my limits.conf file without comments: ubuntu@ip-XX-XXX-XXX-XXX:~$ cat /etc/security/limits.conf | sed '/^#/d;/^$/d' ubuntu soft nofile 65535 ubuntu hard nofile 65535 root soft nofile 65535 root hard nofile 65535 And here is the output of sysctl fs.file-max: ubuntu@ip-XX-XXX-XXX-XXX:~$ sysctl -a| grep fs.file-max sysctl: permission denied on key 'fs.protected_hardlinks' sysctl: permission denied on key 'fs.protected_symlinks' fs.file-max = 1528687 sysctl: permission denied on key 'kernel.cad_pid' sysctl: permission denied on key 'kernel.usermodehelper.bset' sysctl: permission denied on key 'kernel.usermodehelper.inheritable' sysctl: permission denied on key 'net.ipv4.tcp_fastopen_key' as sudo ubuntu@ip-10-102-154-226:~$ sudo sysctl -a| grep fs.file-max fs.file-max = 1528687 Also, I see this error at the top of the redis.log file, not sure if it's related. It makes sense that the ubuntu user isn't allowed to change max open files, but given the high ulimits I have tried to set he shouldn't need to: [1050] 23 Aug 21:00:43.572 # You requested maxclients of 10000 requiring at least 10032 max file descriptors. [1050] 23 Aug 21:00:43.572 # Redis can't set maximum open files to 10032 because of OS error: Operation not permitted.

  Read the article

• How to pass alias through sudo

  - by Tanktalus

  I have an alias that passes in some parameters to a tool that I use often. Sometimes I run as myself, sometimes under sudo. Unfortunately, of course, sudo doesn't recognise the alias. Does anyone have a hint on how to pass the alias through? In this case, I have a bunch of options for perl when I'm debugging: alias pd='perl -Ilib -I/home/myuser/lib -d' Sometimes, I have to debug my tools as root, so, instead of running: pd ./mytool --some params I need to run it under sudo. I've tried many ways: sudo eval $(alias pd)\; pd ./mytool --some params sudo $(alias pd)\; pd ./mytool --some params sudo bash -c "$(alias pd)\; pd ./mytool --some params" sudo bash -c "$(alias pd); pd ./mytool --some params" sudo bash -c eval\ "$(alias pd)\; pd ./mytool --some params" sudo bash -c eval\ "'$(alias pd)\; pd ./mytool --some params'" I was hoping for a nice, concise way to ensure that my current pd alias was fully used (in case I need to tweak it later), though some of my attempts weren't concise at all. My last resort is to put it into a shell script and put that somewhere that sudo will be able to find. But aliases are soooo handy sometimes, so it is a last resort.

  Read the article

• How to grant read/write to specific user in any existent or future subdirectory of a given directory? [migrated]

  - by Samuel Rossille

  I'm a complete newbie in system administration and I'm doing this as a hobby. I host my own git repository on a VPS. Let's say my user is john. I'm using the ssh protocol to access my git repository, so my url is something like ssh://[email protected]/path/to/git/myrepo/. Root is the owner of everything that's under /path/to/git I'm attempting to give read/write access to john to everything which is under /path/to/git/myrepo I've tried both chmod and setfacl to control access, but both fail the same way: they apply rights recursively (with the right options) to all the current existing subdirectories of /path/to/git/myrepo, but as soon as a new directory is created, my user can not write in the new directory. I know that there are hooks in git that would allow me to reapply the rights after each commit, but I'm starting to think that i'm going the wrong way because this seems too complicated for a very basic purpose. Q: How should I setup my right to give rw access to john to anything under /path/to/git/myrepo and make it resilient to tree structure change ? Q2: If I should take a step back change the general approach, please tell me.

  Read the article

• Seizing naming master from child domain server

  - by meera

  when I am trying to seize the role from my child domain server the naming master I get the following error fsmo maintenance: seize naming master Attempting safe transfer of domain naming FSMO before seizure. ldap_modify_sW error 0x34(52 (Unavailable). Ldap extended error message is 000020AF: SvcErr: DSID-03210380, problem 5002 (UN AVAILABLE), data 8438 Win32 error returned is 0x20af(The requested FSMO operation failed. The current FSMO holder could not be contacted.) ) Depending on the error code this may indicate a connection, ldap, or role transfer error. Transfer of domain naming FSMO failed, proceeding with seizure ... Server "win-fb20ixk90mu" knows about 5 roles Schema - CN=NTDS Settings,CN=WIN-3918XHC5STU,CN=Servers,CN=Default-First-Site-Na me,CN=Sites,CN=Configuration,DC=HCL,DC=com Naming Master - CN=NTDS Settings,CN=WIN-FB20IXK90MU,CN=Servers,CN=Default-First- Site-Name,CN=Sites,CN=Configuration,DC=HCL,DC=com PDC - CN=NTDS Settings,CN=WIN-FB20IXK90MU,CN=Servers,CN=Default-First-Site-Name, CN=Sites,CN=Configuration,DC=HCL,DC=com RID - CN=NTDS Settings,CN=WIN-FB20IXK90MU,CN=Servers,CN=Default-First-Site-Name, CN=Sites,CN=Configuration,DC=HCL,DC=com Infrastructure - CN=NTDS Settings,CN=WIN-FB20IXK90MU,CN=Servers,CN=Default-First -Site-Name,CN=Sites,CN=Configuration,DC=HCL,DC=com

  Read the article

• MySQL Config on Large Machine

  - by Jonathon

  We have a Windows 2003 Enterprise Edition server (64bit) running only MySQL 5.1.45 64-bit. It has 16G RAM and 10T of hard-drive space in RAID 10. We are having horrible performance from mysqld (85-100% CPU utilization). We were running a smaller machine with better performance, so I am assuming our my.ini file is not correct for our current machine. The my.ini file is as follows: [client] port=3306 [mysql] default-character-set=latin1 [mysqld] port=3306 basedir="D:/MySQL/" datadir="D:/MySQL/data" default-character-set=latin1 default-storage-engine=MYISAM sql-mode="" skip-innodb skip-locking max_allowed_packet = 1M max_connections=800 myisam_max_sort_file_size=5G myisam_sort_buffer_size=500M table_open_cache = 512 table_cache=8000 tmp_table_size=30M query_cache_size=50M thread_cache_size=128 key_buffer_size=3072M read_buffer_size=2M read_rnd_buffer_size=16M sort_buffer_size=2M #replication settings (this is the master) log-bin=log server-id = 1 Does anyone see anything wrong with this setup? For a machine with this much RAM, why in the world would mysqld eat up so much CPU? I know we can optimize some queries, etc., but it did run okay on a smaller machine, so I am pretty sure it is the config. Thanks in advance for any help.

  Read the article

< Previous Page | 527 528 529 530 531 532 533 534 535 536 537 538  | Next Page >