Search Results

Search found 60836 results on 2434 pages for 'system io directory'.

Page 532/2434 | < Previous Page | 528 529 530 531 532 533 534 535 536 537 538 539  | Next Page >

• Ubuntu 12.04 boot degraded raid

  - by beacon_bonanza

  I've installed Ubuntu 12.04.1 in a new server and set up the 4 hard drives with 3 RAID 1 devices, the configuration is such that the first two drives have md0 (swap space) and md1 (/) with the third and fourth drives having md2 (/var). I've been testing the operation under a drive failure and found that the system boots fine if I remove disk two but if I remove disk one then the system gets to grub and then just restarts. I'm confused as to why grub appears to be loading properly from disk two but then the boot fails. I've tried to copy the MBR from disk 1 to 2: dd if=/dev/sda of=/dev/sdb bs=512 count=1 but this didn't make a difference. Any ideas how to get it to boot from just the second disk? fdisk -l Disk /dev/sda: 2000.4 GB, 2000398934016 bytes 255 heads, 63 sectors/track, 243201 cylinders, total 3907029168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000ccfa5 Device Boot Start End Blocks Id System /dev/sda1 2048 31250431 15624192 fd Linux RAID autodetect /dev/sda2 * 31250432 3907028991 1937889280 fd Linux RAID autodetect Disk /dev/sdb: 2000.4 GB, 2000398934016 bytes 255 heads, 63 sectors/track, 243201 cylinders, total 3907029168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000ccfa5 Device Boot Start End Blocks Id System /dev/sdb1 2048 31250431 15624192 fd Linux RAID autodetect /dev/sdb2 * 31250432 3907028991 1937889280 fd Linux RAID autodetect Disk /dev/sdd: 2000.4 GB, 2000398934016 bytes 255 heads, 63 sectors/track, 243201 cylinders, total 3907029168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00035b05 Device Boot Start End Blocks Id System /dev/sdd1 2048 3907028991 1953513472 fd Linux RAID autodetect Disk /dev/sdc: 2000.4 GB, 2000398934016 bytes 255 heads, 63 sectors/track, 243201 cylinders, total 3907029168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000c73aa Device Boot Start End Blocks Id System /dev/sdc1 2048 3907028991 1953513472 fd Linux RAID autodetect Disk /dev/md1: 1984.3 GB, 1984264208384 bytes 2 heads, 4 sectors/track, 484439504 cylinders, total 3875516032 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/md2: 2000.3 GB, 2000263380992 bytes 2 heads, 4 sectors/track, 488345552 cylinders, total 3906764416 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/md0: 16.0 GB, 15990652928 bytes 2 heads, 4 sectors/track, 3903968 cylinders, total 31231744 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000

  Read the article

• Recommended partitions to migrate from Windows XP to Windows 7 and Ubuntu

  - by Juanillo

  Hello, I have a system with Windows XP. My hard disk has 189 GB NTFS. I want to change the operative system to windows 7, but I want to add Ubuntu as well. As the change might take several days (because I don't have much time) I want to install one system (or Windows 7 or Ubuntu) keeping my windows XP installed in another partition so if something doesn't work in thebrand new operating system installed I can use my Windows XP installation. So I've thouht about doing something like this: Copy the data I want to keep to an external hard disk. Make partitions enough to install windows 7, keep data in another partition and another one to install Ubuntu. Copy the data I want to keep to the partition I've just created. Install Ubuntu in the partitions for Ubuntu. Check if Ubuntu works fine If it works OK install Windows 7 on the partition of Windows XP (Windows XP will be erased). Reinstall the programs in Windows 7. So my question is: How many partitions do you recommend me to have (and the size of each one and NTFS or FAT32)? The operative system I'm going to use more is Windows 7 (though I love Linux I use many programs which are windows dependant). Do you think I should do anything else / change something in the proccess to avoid any problem? I don't know if making the partitions can harm the data I have in the disk. Thanks.

  Read the article

• Migration from XP to Windows 7 using recovered HD

  - by KenK

  Is it possible to migrate the Windows XP Pro 32 bit operating system, applications etc from a USB external drive which is the recovered hard drive from that failed system to my new desktop computer with Windows7 64 bit system? In doing so, I would like to set up the new computer with the OS and all general applications on the primary 1TB hard drive while the secondary 1TB hard drive to have nothing else but graphics programs and gaming applications complete with their related files and add-ons. What will I need to accomplish this task efficiently and economically?

  Read the article

• Mod_rewrite (CakePHP routing functionality) forbidden after Snow Leopard upgrade

  - by Ryan Ballantyne

  Hello ServerFault, I am using the standard Apple-provided installations of PHP 5.3 and Apache 2 to do web development on a Mac Pro that I just upgraded to Mac OS X 10.6 (Snow Leopard). The upgrade went well enough, if I ignore the fact that it destroyed my ability to get work done. ;) After the update, the CakePHP application I was developing started giving me 403 Forbidden errors when accessed. Based on the errors in the log file, I've determined that Apache is choking on the mod_rewrite rules in Cake's .htaccess file. Here's the file, in its entirety: <IfModule mod_rewrite.c> RewriteEngine on RewriteRule ^$ app/webroot/ [L] RewriteRule (.*) app/webroot/$1 [L] </IfModule> It's not that the rules themselves are wrong, but that Apache is forbidding the use of mod_rewrite altogether. All other pages on the machine work fine, and the 403 errors go away if I comment out the .htaccess file (but nothing works, of course). In my httpd.conf file, I've tried changing this: <Directory /> Options FollowSymLinks AllowOverride None Order deny,allow Deny from all </Directory> To this: <Directory /> Options FollowSymLinks AllowOverride All Order deny,allow Allow from all </Directory> ...which has no effect. I don't know much about Apache configuration files, and I'm quite stuck on this. In fact, I know little enough that I'm not sure which information about my setup is needed to enable people to provide useful answers. I'm just using the vanilla OS X setup, nothing fancy. Googling has yielded no fruits for me this time, so I'm turning to you. Any ideas?

  Read the article

• Problem adding second domain controller to SBS 2008

  - by Quango

  Have an SBS 2008 server in one location, and want to add a backup domain controller at a different site. The two sites are linked by a VPN. New server is running Server 2008 R2, fully patched. At present it is a member server and the DNS is pointing at the SBS DNS. When I try running DCPROMO to connect the server, the wizard runs fine up to the point where the wizard is 'configuring Active Directory Domain Services' and 'examining forest': "The operation failed because: The wizard could not read operational attributes from the remote Active Directory Domain Controller SERVER.DOMAIN.LOCAL using LDAP. "The specified server cannot perform the requested operation." This error can occur if you have not been granted necessary permissions to read data in the directory. For more information, please see article 936241 in the Microsoft Knowledge Base (http://go.microsoft.com/fwlink/?LinkId=88420)." I was logged on as domain administrator. Interestingly the link is invalid and the KB article does not exist..! Settings: Configure this server as an additional Active Directory domain controller for the domain "[domain]". Site: [site] Additional Options: Read-only domain controller: "No" Global catalog: Yes DNS Server: Yes Update DNS Delegation: No Source domain controller: any writable domain controller Database folder: C:\Windows\NTDS Log file folder: C:\Windows\NTDS SYSVOL folder: C:\Windows\SYSVOL The DNS Server service will be configured on this computer. This computer will be configured to use this DNS server as its preferred DNS server.

  Read the article

• Hostname and SSL (apache) issue on Debian

  - by user105566

  I have been trying to setup SSL virtual host ServerAdmin [email protected] ServerName moclm.tap.pt DocumentRoot /var/www/tapme/ <Directory /> Options FollowSymLinks AllowOverride All Order deny,allow Deny from all Allow from 127.0.0.0/255.0.0.0 ::1/128 </Directory> <Directory /var/www/tapme/> Options -Indexes FollowSymLinks MultiViews AllowOverride All #Order allow,deny #allow from all </Directory> SSLEngine on SSLCertificateFile /etc/ssl/moclm.cer SSLCertificateKeyFile /etc/ssl/moclm.pem </VirtualHost> For some reason, the server automatically redirect to SSL (http:// to https://). The apache is not configured to redirect and application was working fine on port 80 only. I have no knowledge how the internal network works as i am working remotely. The SSL error logs show: [Tue Oct 02 22:40:32 2012] [error] Hostname linemnt01.tap.pt provided via SNI and hostname moclm.tap.pt provided via HTTP are different I thought may be the hostname has some issue and have changed the hostname of the server from "linemnt01.tap.pt" to "moclm.tap.pt" but the issue is still there. I am getting the following error on browser: Bad Request Your browser sent a request that this server could not understand. i have /etc/hosts: 127.0.0.1 localhost.localdomain localhost moclm.tap.pt moclm and openssl returns: openssl verify -CAfile cert-CA.cer moclm.cer moclm.tap.pt.cer: OK I have been trying to troubleshoot the issue but no luck. Need help Thanks

  Read the article

• How can I debug user mode driver failures in Windows 8

  - by Tom

  I have a 32 GB SD Card. Whenever I insert this card in to my newly upgraded Windows 8 laptop the OS stops responding normally. Metro Apps won't work. The system may or may not log in. Desktop apps may or may not be able to do things. When I remove the card and restart then all is fine. As soon as I put the card back in, the system starts misbehaving again. I've run Windows Update, so I have the latest drivers from Microsoft. This does not occur with the 8 GB cards I have. Unfortunately I only have one 32 GB card, so I can't test with others. From examining the system event log I've determined this is happening due to a user mode driver failure. How can I best debug this issue from here? How can I figure out which driver this is related to? Will there be a Dr. Watson crash dump somewhere? Details - System - Provider [ Name] Microsoft-Windows-DriverFrameworks-UserMode [ Guid] {2E35AAEB-857F-4BEB-A418-2E6C0E54D988} EventID 10110 Version 1 Level 1 Task 64 Opcode 0 Keywords 0x2000000000000000 - TimeCreated [ SystemTime] 2012-10-29T00:51:57.532718300Z EventRecordID 40417 Correlation - Execution [ ProcessID] 1056 [ ThreadID] 3796 Channel System Computer thebrain - Security [ UserID] S-1-5-18 - UserData - UMDFHostProblem [ lifetime] {811E3DC4-FBC6-420B-ABCC-AD7505A36F3B} - Problem [ code] 3 [ detectedBy] 2 ExitCode 3 - Operation [ code] 259 Message 72448 Status 4294967295 Edit 1 So I tried using Debug View from SysInternals (you can get it here: http://technet.microsoft.com/en-us/sysinternals/bb896647.aspx). That gave me this information: which is not especially helpful. Then I tried connecting WinDbg to WUDFHost.exe (the process that seems to host user mode drivers) to see if it could catch the error. Get it here: http://msdn.microsoft.com/en-US/windows/hardware/hh852363 Instructions: http://msdn.microsoft.com/en-US/library/windows/hardware/ff554716(v=vs.85).aspx That didn't help much. It didn't catch any exceptions as I'd hoped (which would point me to the cause of the crash at least). Here's the stack of one of the threads:

  Read the article

• Slow solid state drive on laptop running Linux

  - by wcyang

  I installed a solid state drive on my laptop, but I don't get the blazing speeds which people write about. My system: Laptop: Acer Aspire 7552G-6061 Solid state drive: Crucial 256GB M4 CT256M4SSD2 Operating system: Linux (Trisquel 5.5, a derivative of Ubuntu) I am using AHCI. I installed the operating system onto the solid state drive (as opposed to copying it). How can I make the solid state drive faster? Could the problem be with the block or sector alignment?

  Read the article

• DIR $file "File Not Found" vs DIR $filedir shows it....not permissions, not USB

  - by Kev

  I was having this problem before on a USB drive, but now it's happening on my main RAID5-backed hard disk: 2013-10-17 9:37 C:\>dir "C:\Shares\Shared\Reference\Safety Management System\Vid eo CD\AutoPlay\Docs\Manuel*" Volume in drive C has no label. Volume Serial Number is 3C18-E114 Directory of C:\Shares\Shared\Reference\Safety Management System\Video CD\AutoP lay\Docs 2003-09-09 11:29 PM 1,056,768 Manuel d'intervention d'urgence MFC.doc 2004-06-20 10:36 PM 139,849 Manuel d'intervention d'urgence MFC.pdf 2 File(s) 1,196,617 bytes 0 Dir(s) 196,068,691,968 bytes free 2013-10-17 9:38 C:\>dir "C:\Shares\Shared\Reference\Safety Management System\Vid eo CD\AutoPlay\Docs\Manuel d'intervention d'urgence MFC.doc" Volume in drive C has no label. Volume Serial Number is 3C18-E114 Directory of C:\Shares\Shared\Reference\Safety Management System\Video CD\AutoP lay\Docs File Not Found 2013-10-17 9:38 C:\> This is from a Command Prompt window where I went to Properties and told it I wanted to modify who it ran as. I opened it, had it run as me with the "restricted access" unchecked, then ran the above. The file in question has the following ACLs: Administrators, SYSTEM, and OurCompanyUsers. All three have full control of everything. Nobody has any Deny bits set. I am a member of Administrators. So I don't believe it's a permissions issue. It's not a USB drive, so this time there is no question of USB hardware. Windows Server 2003 Standard Edition SP2. What does this mean? Is this more likely a hardware or software problem?

  Read the article

• Is the master database backup crucial for restoring MS SQL server in the event where you have to res

  - by Imagineer

  I have been advise by Commvault partner support to turn off the backup of the master database as the backup failed due to the log file being lock. The following is the advise given: "The message is caused by Commvault’s inability to backup the master database’s transaction log. If this is happening intermittently its possible that something is locking the transaction log, preventing SQL iData agent from accessing the log. Typically the master database is just a template and is not used by any applications (applications that do require the use of an SQL database create their own) so there should be no harm in preventing it from being backed up You can do this by nominating NOT to back it up in the primary copy for the SQL data agent" The following is the error that I get. sqlxx SQL Server/ SQLxx N/A/ System DBs 19856* (CWE) Transaction Log N/A 01/08/2010 19:00:16 (01/08/2010 19:00:18 ) 01/08/2010 19:03:15 (01/08/2010 19:03:14 ) 1.44 MB 0:01:11 0.071 2 0 1 ITD014L2 Failure Reason: • ERROR CODE [30:325]: Error encountered during backup. Error: [ERROR: [Microsoft][ODBC SQL Server Driver][SQL Server]Cannot back up the log of the master database. Use BACKUP DATABASE instead. [Microsoft][ODBC SQL Server Driver][SQL Server]BACKUP LOG is terminating abnormally.] Job Options:Create new index, Start new media, Backup all subclients, Truncation Log, Follow mount points , Backup files protected by system file protection , Stop DHCP service when backing up system state data, Stop WINS service when backing up system state data Associated Events: • 79714 [backupxx/JobManager] [01/08/2010 19:03:15 ]: Backup job [19856] completed. Client [sqlxx], Agent Type [SQL Server], Subclient [System DBs], Backup Level [Transaction Log], Objects [2], Failed [1], Duration [00:02:59], Total Size [1.44 MB], Media or Mount Path Used [ITD014L2]. • 79712 [sqlxx/SQLiDA] [01/08/2010 19:01:53 ]: Error encountered during backup. Error: [ERROR: [Microsoft][ODBC SQL Server Driver][SQL Server]Cannot back up the log of the master database. Use BACKUP DATABASE instead. [Microsoft][ODBC SQL Server Driver][SQL Server]BACKUP LOG is terminating abnormally.] • 79711 [sqlxx/SQLiDA] [01/08/2010 19:01:51 ]: Query Result [[Microsoft][ODBC SQL Server Driver][SQL Server]Cannot back up the log of the master database. Use BACKUP DATABASE instead. [Microsoft][ODBC SQL Server Driver][SQL Server]BACKUP LOG is terminating abnormally.]. • 79707 [backupxx/JobManager] [01/08/2010 19:00:15 ]: New backup request received for Client [sqlxx], iDataAgent [SQL Server], Instance [SQLxx], Subclient [System DBs], Backup Level [Transaction Log]. Files failed to back up: • Backup Database[master] Failed Please advise, thank you.

  Read the article

• SYS-5016T-MTFB will not POST without manual assistance (Motherboard: X8STi-F)

  - by Dan

  I have a Supermicro 5016T-MTFB 1U server which I am in the process of setting up, but it has a really strange problem. When the system is powered on it will not POST until I press the reset button a few times, followed by pressing the delete key on the keyboard to "wake it up". If I power it on and do nothing, the fans spin up but nothing else happens at all. After pressing the reset button once, the red "overheat" light comes on and blinks which is supposed to indicate a fan failure - but all the fans are working. Pressing reset again usually stops the blinking, and the system starts the normal POST routine but it will not actually get to the bios screen unless I press delete. If I don't press delete, it just continues to hang. After pressing delete it will take me into the bios setup screen, if I exit without saving changes I can boot the system normally. I was able to successfully install Linux with no trouble...but upon rebooting the same problem happened again. This board has integrated IPMI which I thought was the problem, so I disabled it via the jumper on the board. Did not help. Each time this system powers on, it goes on for a second, then turns off again for another second, then turns back on again. I don't know why it does that. Here is what I put in the system: 1 x Xeon E5630 (Nehalem) 80W TDP (it's not overheating, CPU temps stay under 40 degrees C) 2 x Kingston 2GB x 3 DDR3-1066 Memory ECC, unbuffered, unregistered (kvr1066d3e7sk3/6g) 1 x Intel X25-M 160 GB 2 x Western Digital RE3 1TB

  Read the article

• Setting up subdomain to respond on :443 with apache2

  - by compucuke

  I read through some guides on this and I believe it is possible to have apache respond to a subdomain through ssl. I have domain.com responding on 80 and I do not need domain.com responding on 443. Rather, the only use I have for ssl is for the subdomain sub.domain.com. So my site should be http://domain.com http://www.domain.com https://sub.domain.com https://www.sub.domain.com My CNAME records are as follows sub.domain.com xxx.xx.xx.xxx *.sub.domain.com xxx.xx.xx.xxx The A record exists but should not matter for the example. I set up a separate config file in sites-enabled for sub.domain.com NameVirtualHost xxx.xx.xx.xxx:443 <VirtualHost xxx.xx.xx.xxx:443> SSLEngine on SSLStrictSNIVHostCheck on SSLProtocol -ALL +SSLv3 +TLSv1 SSLCipherSuite ALL:!aNULL:!ADH:!eNULL:!LOW:!EXP:RC4+RSA:+HIGH:-MEDIUM ServerAlias sub.domain.com DocumentRoot /usr/local/www/ssl/documents/ SSLCertificateFile /root/sub.domain.com.crt SSLCertificateKeyFile /root/sub.domain.com.key Alias /robots.txt /usr/local/www/ssl/documents/robots.txt Alias /favicon.ico /usr/local/www/ssl/documents/favicon.ico Alias /js/libs /usr/local/www/ssl/documents/js/libs Alias /media/ /usr/local/www/documents/media/ Alias /img/ /usr/local/www/ssl/documents/img/ Alias /css/ /usr/local/www/ssl/documents/css/ <Directory /usr/local/www/ssl/documents/> Order allow,deny Allow from all </Directory> WSGIDaemonProcess sub.domain.com processes=2 threads=7 display-name=%{GROUP} WSGIProcessGroup sub.domain.com WSGIScriptAlias / /usr/local/www/wsgi-scripts/script.wsgi <Directory /usr/local/www/wsgi-scripts> Order allow,deny Allow from all </Directory> </VirtualHost> Now, it is important to mention that https://domain.com responds with what I have running from script.wsgi above instead of on https://sub.domain.com. It does not respond to sub.domain.com. checking https://sub.domain.com causes a 105 error. This is a DNS error but I am convinced the DNS does not have a problem with the CNAME records, they just point to my IP. Am I doing something that Apache can not do?

  Read the article

• Only 2.99 Gb RAM usable out of 8GB in Windows 8 32 bit [closed]

  - by user1832280

  Possible Duplicate: 8gb ram in 32bit operating system I have installed 8 GB RAM in my system. Also upgraded OS to Windows 8 32 bit. My System configuration: Intel i7 960. Ram Crossair 4 GB X 2 1666Mhz Motherboard Asus Rampage III Gene Video card: NVIDIA GeForce GT 240. 2 TB Seagate I have updated all drivers BIOS also. But my system showing only 2.99 GB out of 8GB usable RAM. Please help me fix this problem.

  Read the article

• Apache directive for authenticated users?

  - by Alex Leach

  Using Apache 2.2, I would like to use mod_rewrite to redirect un-authenticated users to use https, if they are on http.. Is there a directive or condition one can test for whether a user is (not) authenticated? For example, I could have set up the restricted /foo location on my server:- <Location "/foo/"> Order deny,allow # Deny everyone, until authenticated... Deny from all # Authentication mechanism AuthType Basic AuthName "Members only" # AuthBasicProvider ... # ... Other authentication stuff here. # Users must be valid. Require valid-user # Logged-in users authorised to view child URLs: Satisfy any # If not SSL, respond with HTTP-redirect RewriteCond ${HTTPS} off RewriteRule /foo/?(.*)$ https://${SERVER_NAME}/foo/$2 [R=301,L] # SSL enforcement. SSLOptions FakeBasicAuth StrictRequire SSLRequireSSL SSLRequire %{SSL_CIPHER_USEKEYSIZE} >= 128 </Location> The problem here is that every file, in every subfolder, will be encrypted. This is quite unnecessary, but I see no reason to disallow it. What I would like is the RewriteRule to only be triggered during authentication. If a user is already authorised to view a folder, then I don't want the RewriteRule to be triggered. Is this possible? EDIT: I am not using any front-end HTML here. This is only using Apache's built-in directory browsing interface and its in-built authentication mechanisms. My <Directory> config is: <Directory ~ "/foo/"> Order allow,deny Allow from all AllowOverride None Options +Indexes +FollowSymLinks +Includes +MultiViews IndexOptions +FancyIndexing IndexOptions +XHTML IndexOptions NameWidth=* IndexOptions +TrackModified IndexOptions +SuppressHTMLPreamble IndexOptions +FoldersFirst IndexOptions +IgnoreCase IndexOptions Type=text/html </Directory>

  Read the article

• OSX 10.6 integration into NIS/netgroup/automount infrastructure

  - by mdpc

  I have an existing infrastructure where accounts are maintained under NIS (yp) with no local unix accounts. Also, all the standard maps including hosts, mail aliases, netgroups, etc...are maintained in this form. Extensive use of the UNIX/Linux automounter with items scattered over the network on NFS servers. There are NO ACLs on any local or shared files. All mail needs to use basically the nullclient sendmail configuration feeding into a different system. I now have a requirement to integrate an Apple OSX 10.6 system into this environment and make it run seamlessly. My initial reading and second-hand information seems to indicate that this may not be possible on the native OSX 10.6 system. I'm concerned. Any ideas as to how to accomplish this task and make everybody happy? Thanks PS: I have never used an Apple OSX system.

  Read the article

• Windows 7 Goes to Sleep in conflict with Power Option Setting

  - by Decker

  My Del Dimension E521 running Windows 7 puts itself in sleep mode each night -- despite the fact that I have chosen a power option that specifies NEVER Each morning I find the monitor blank and I have to hit the power button on the PC at which point Windows "resumes". The system event log shows this: Source: Microsoft-Windows-Kernel-Power Date: 3/27/2010 3:21:10 AM Description: The system is entering sleep. Sleep Reason: System Idle My specific power options are: Turn off Display : 20 Minutes Put the computer to sleep : Never Is there some other setting coming into play here?

  Read the article

• Batch deletion of smaller files from group of files via unix command line

  - by artlung

  I have a large number (more than 400) of directories full of photos. What I want to do is to keep the larger sizes of these photos. Each directory has 31 to 66 files in it. Each directory has thumbnails, and larger versions, plus a file called example.jpg I dispatched the example.jpg file easily with: rm */example.jpg I initially thought that it would be easy to delete the thumbnails, but the problem is they are not consistently named. The typical pattern was photo1.jpg and photo1s.jpg. I did rm */photo*s.jpg but it ended up some of the files named photoXs.jpg were actually larger and not smaller. Argh. So what I want to do is scan each directory for filesize and delete (or move) the thumbnails. I initially thought I'd just ls -R every file and extract the size of each file and save those under a threshold. The problem? In one directory the large will be 1.1 MB and the thumb is 200k. In another the large is 200k and the small 30k. Even worse, the files really are mostly named photo1.jpg - so simply putting them all in the same folder, sorting by size, and deleting in groups would not work without renaming already, and if it's possible I'd prefer to keep them in their folders. I was almost resolved to just doing this all manually, but then thought I'd ask here. How would you do this task?

  Read the article

• Password Cracking Windows Accounts

  - by Kevin

  At work we have laptops with encrypted harddrives. Most developers here (on occasion I have been guilty of it too) leave their laptops in hibernate mode when they take them home at night. Obviously, Windows (i.e. there is a program running in the background which does it for windows) must have a method to unencrypt the data on the drive, or it wouldn't be able to access it. That being said, I always thought that leaving a windows machine on in hibernate mode in a non-secure place (not at work on a lock) is a security threat, because someone could take the machine, leave it running, hack the windows accounts and use it to encrypt the data and steal the information. When I got to thinking about how I would go about breaking into the windows system without restarting it, I couldn't figure out if it was possible. I know it is possible to write a program to crack windows passwords once you have access to the appropriate file(s). But is it possible to execute a program from a locked Windows system that would do this? I don't know of a way to do it, but I am not a Windows expert. If so, is there a way to prevent it? I don't want to expose security vulnerabilities about how to do it, so I would ask that someone wouldn't post the necessary steps in details, but if someone could say something like "Yes, it's possible the USB drive allows arbitrary execution," that would be great! EDIT: The idea being with the encryption is that you can't reboot the system, because once you do, the disk encryption on the system requires a login before being able to start windows. With the machine being in hibernate, the system owner has already bypassed the encryption for the attacker, leaving windows as the only line of defense to protect the data.

  Read the article

• apache2: Could not reliably determine the server's fully qualified domain name, using 127.0.1.1 for ServerName

  - by user35402

  I keep getting this warning when I (re)start Apache. Restarting web server apache2 apache2: Could not reliably determine the server's fully qualified domain name, using 127.0.1.1 for ServerName ... waiting apache2: Could not reliably determine the server's fully qualified domain name, using 127.0.1.1 for ServerName [ OK ] This is the content of my etc/hosts file: #127.0.0.1 hpdtp-ubuntu910 #testproject.localhost localhost.localdomain localhost #127.0.1.1 hpdtp-ubuntu910 127.0.0.1 localhost 127.0.0.1 testproject.localhost 127.0.1.1 hpdtp-ubuntu910 # The following lines are desirable for IPv6 capable hosts ::1 localhost ip6-localhost ip6-loopback fe00::0 ip6-localnet ff00::0 ip6-mcastprefix ff02::1 ip6-allnodes ff02::2 ip6-allrouters ff02::3 ip6-allhosts This is the content of my /etc/apache2/sites-enabled/000-default file: <VirtualHost *:80> ServerName testproject.localhost DocumentRoot "/home/morpheous/work/websites/testproject/web" DirectoryIndex index.php <Directory "/home/morpheous/work/websites/testproject/web"> AllowOverride All Allow from All </Directory> Alias /sf /lib/vendor/symfony/symfony-1.3.2/data/web/sf <Directory "/lib/vendor/symfony/symfony-1.3.2/data/web/sf"> AllowOverride All Allow from All </Directory> </VirtualHost> When I go to http://testproject.localhost, I get a blank page can anyone spot what I am doing wrong?

  Read the article

• Cannot boot from windows 7 DVD

  - by webnoob

  Hi All, I have just purchased windows 7 64bit. I entered the disk in the drive and it told me I couldn't upgrade as I am using XP so I have tried to boot from CD instead but it doesn't work. It seems to look at the disk for a few seconds and then ends up at a screen saying windows failed to start and then I hit enter and it loads windows XP again. Does anyone know what could cause this? Here is my system info: Time of this report: 4/15/2010, 18:11:39 Machine name: MYCOMP Operating System: Windows XP Professional (5.1, Build 2600) Service Pack 3 (2600.xpsp_sp3_gdr.100216-1514) Language: English (Regional Setting: English) System Manufacturer: Dell Inc. System Model: OptiPlex 755 BIOS: Phoenix ROM BIOS PLUS Version 1.10 A09 Processor: Intel(R) Core(TM)2 Duo CPU E6550 @ 2.33GHz (2 CPUs) Memory: 3316MB RAM Page File: 568MB used, 4631MB available Windows Dir: C:\WINDOWS DirectX Version: DirectX 9.0c (4.09.0000.0904) DX Setup Parameters: Not found DxDiag Version: 5.03.2600.5512 32bit Unicode

  Read the article

• Cannot boot from windows 7 DVD

  - by webnoob

  Hi All, I have just purchased windows 7 64bit. I entered the disk in the drive and it told me I couldn't upgrade as I am using XP so I have tried to boot from CD instead but it doesn't work. It seems to look at the disk for a few seconds and then ends up at a screen saying windows failed to start and then I hit enter and it loads windows XP again. Does anyone know what could cause this? Here is my system info: Time of this report: 4/15/2010, 18:11:39 Machine name: MYCOMP Operating System: Windows XP Professional (5.1, Build 2600) Service Pack 3 (2600.xpsp_sp3_gdr.100216-1514) Language: English (Regional Setting: English) System Manufacturer: Dell Inc. System Model: OptiPlex 755 BIOS: Phoenix ROM BIOS PLUS Version 1.10 A09 Processor: Intel(R) Core(TM)2 Duo CPU E6550 @ 2.33GHz (2 CPUs) Memory: 3316MB RAM Page File: 568MB used, 4631MB available Windows Dir: C:\WINDOWS DirectX Version: DirectX 9.0c (4.09.0000.0904) DX Setup Parameters: Not found DxDiag Version: 5.03.2600.5512 32bit Unicode

  Read the article

• Gray Progress Bar in Macbook Boot caused by Partition Fault

  - by Konstantin Bodnya

  Here's my problem: When I try to load my macbook it shows the gray progress bar. It takes a while to fill the whole progress and after it macbook just shuts down. I tried to boot from recovery partition and run Disk Utility to repair it. Disk Utility showed my "Macintosh HD" in a gray color and failed to repair it. I thought all my data was lost, but then I tried the following: So I booted into ubunto from live usb and it successfully mounted my macintosh hd hfs+ partition. Parted shows me the following partitions on my disk: Disk /dev/sda: 500GB Sector size (logical/physical): 512B/512B Partition Table: gpt Number Start End Size File system Name Flags 1 20.5kB 210MB 210MB fat32 EFI System Partition boot 2 210MB 499GB 499GB hfs+ Macintosh HD 3 499GB 500GB 650MB hfs+ Recovery HD Seems legit except for FAT32 for EFI System Partition. Since all my data is okay and backed up what should I do to recover the system. I don't really want to reinstall all the system though I believe there's a command to make it allright in linux. Thank you everyone!

  Read the article

• Editing sudoers file to restrict a user's commands

  - by devin

  Is it possible to edit the sudoers file so a user can use sudo for any command except for a specified one? I reverse is true, I believe, that the sudoers file can be setup so that a user can only execute a given list of commands. EDIT: the commands I really want to take away are halt and reboot... this makes me think there are special system calls for halt and reboot. Can you take system calls away from a user? If not, is it because the unix permission system abstracts over system calls neglecting this?

  Read the article

• Mobile Intel® GMA 4500MHD boost

  - by Andy Smith

  My machine has a Mobile Intel® GMA 4500MHD integrated graphics chipset. The machine is currently running 64 bit windows 7 premium with 3GB of ram (1x1gb and 1x2gb). I note that the Mobile Intel® GMA 4500MHD shares the physical memory to process the graphics. now, the total available graphics memory can be up to 1,340 MB with a 32-bit operating system and 3 GB system memory or 1,759 MB with a 64-bit operating system and 4 GB system memory. I am considering investing in a 4GB stick to replace the 1gb stick bringing the total up to 6gb, mainly for an increase in graphics processing ability. Can anyone let me know what sort of power (if any over the 4gb) I could expect by upgrading to 6GB?

  Read the article

• Assets not served - Apache Reverse proxy - Diaspora

  - by Matt

  I have succeeded in installing Diaspora* on my subdomain diaspora.mattaydin.com. I have VPS running CentOS 5.7 with Plesk installed. By means of an vhost.conf and vhost_ssl.conf file I, (with the help of another gentleman) have managed to reverse proxy the app. vhost.conf: ServerName diaspora.mattaydin.com ServerAlias *.diaspora.mattaydin.com <Directory /home/diaspora/diaspora/public> Options -Includes -ExecCGI </Directory> DocumentRoot /home/diaspora/diaspora/public RedirectPermanent / https://diaspora.mattaydin.com vhost_ssl.conf ServerName diaspora.mattaydin.com DocumentRoot /home/diaspora/diaspora/public RewriteEngine On RewriteCond %{DOCUMENT_ROOT}/%{REQUEST_FILENAME} !-f RewriteRule ^/(.*)$ balancer://upstream%{REQUEST_URI} [P,QSA,L] <Proxy balancer://upstream> BalancerMember http://127.0.0.1:3000/ </Proxy> ProxyRequests Off ProxyVia On ProxyPreserveHost On RequestHeader set X_FORWARDED_PROTO https <Proxy *> Order allow,deny Allow from all </Proxy> <Directory /home/diaspora/diaspora/public> Options -Includes -ExecCGI Allow from all AllowOverride all Options +Indexes </Directory> DocumentRoot /home/diaspora/diaspora/public Basically it's working. However, the only thing that's not working are the assets. The do not get loaded not the server, as seen on diaspora.mattaydin.com The error messages I get in the access_ssl.log are a lot of: 11/Dec/2012:19:04:05 +0100] "GET /robots.txt HTTP/1.1" 404 2811 "-" "Mozilla/5.0 (Macintosh; Intel Mac OS X 10_8_2) AppleWebKit/536.26.17 (KHTML, like Gecko) Version/6.0.2 Safari/536.26.17" The error messages I get from diaspora's log file is: Started GET "//assets/branding/logo_large.png" for 77.250.99.193 at 2012-12-11 20:13:11 +0100 ActionController::RoutingError (No route matches [GET] "/assets/branding/logo_large.png"): lib/rack/chrome_frame.rb:39:in call' lib/unicorn_killer.rb:35:incall' Hope you guys can help me out. If you need anything else please let me know Thanks in advance, Matt

  Read the article

< Previous Page | 528 529 530 531 532 533 534 535 536 537 538 539  | Next Page >