Search Results

Search found 15903 results on 637 pages for 'mapping model'.

Page 537/637 | < Previous Page | 533 534 535 536 537 538 539 540 541 542 543 544  | Next Page >

• Why does my PC successfully boot only when unplugged for more than a few minutes?

  - by philg

  I have an HP Pavilion Elite desktop computer, model HPE-490t. I like it because it didn’t cost too much, boots itself from an SSD, came with 16 GB of RAM, and has 6 CPU cores for editing video and camera RAW images. It has one behavioral quirk that I cannot explain, however. The recent power interruptions here in the Northeast got the machine into a state where it could not be restarted. It would power up for a second or two, shut down, and then power up again, never being able to get to the point of showing anything on the monitor. I unplugged it for about 10 seconds and plugged it back in. Same behavior (fails to boot). I unplugged it and walked away for an hour, then plugged it back in and it worked perfectly! I think something similar happened after installing a second hard disk drive into this machine. So the question is why does the computer behave differently depending on how long it has been unplugged? Where is energy stored that affects the machine’s ability to boot? Capacitors in the power supply? Battery on the motherboard (there is one for the clock, but that wouldn’t be exhausted by being unplugged for an hour, I don’t think)?

  Read the article

• HP DL185 - very slow disk read speed

  - by fistameeny

  Hi, I have a HP DL185 G6 Server (12 disk model) with the following spec: Quad Core Xeon 2.27GHz 6GB RAM HP P212 RAID controller with battery backup 2 x 128GB 15K SAS 3.5" (RAID-1 for the operating system) 4 x 750GB 7.5K SAS 3.5" (RAID-5 for the data, 2TB usable space) The operating system is Ubuntu Server 9.10. Both drives have been formatted as EXT4. We are finding that read speed of the RAID-5 array is poor. Disk test results below: sudo hdparm -tT /dev/cciss/c0d1p1 /dev/cciss/c0d1p1: Timing cached reads: 15284 MB in 2.00 seconds = 7650.18 MB/sec Timing buffered disk reads: 74 MB in 3.02 seconds = 24.53 MB/sec For info, the RAID-1 array performs as follows: sudo hdparm -tT /dev/cciss/c0d0p1 /dev/cciss/c0d0p1: Timing cached reads: 15652 MB in 2.00 seconds = 7834.26 MB/sec Timing buffered disk reads: 492 MB in 3.01 seconds = 163.46 MB/sec We thought this was because with no battery, read/write cache is disabled. We have bought and installed the battery backup and have used the HP bootable CD to change the cache settings to 50% read / 50% write and check cache is enabled on the drives and the controller. Is there something I'm missing?

  Read the article

• Toshiba Satellite P755D USB 3.0 Drivers Missing - Windows 7 Professional

  - by nicorellius

  I bought a Toshiba Satellite P755D recently and installed Windows 7 Professional on the machine. It runs great. But I noticed the exclamation point in the yellow triangle icon in the Device Manager next to the Universal Serial Buss (USB) Controller (I'm assuming this is the USB 3.0 controller because mine doesn't recognize devices). Normally, when this kind of thing happens I go to the manufacturer's website and download appropriate drivers and call it a day. But not this time... I browsed to my model and found no driver for the USB 3.0 controller. I tried other HW and Utility drivers, thinking they would be bundled. No luck. I tried looking up the motherboard in my machine. Generic name, no luck. I then called Toshiba technical support and they tried basic troubleshooting, eg, uninstall device, reboot, for auto-installation; no luck. I popped the Windows 7 disk back in and tried to get information that way, no luck. Finally, the technical support guy said he would look into the engineer's system to see if there was a specific driver available and that's where I'm at. The technician told me that these USB 3.0 drivers come within the native driver pack in windows but that doesn't seem to be the case. Any ideas? EDIT - See attached screen shots.

  Read the article

• Issues regarding internet connectivity

  - by andySF

  Hello. My problem started when Yahoo Messenger stopped connecting. I've tried to see if Internet Explorer was working but will not load any page. The diagnostics of Internet Explorer says that is something wrong with my dns(using just ip of google or yahoo or my local webserver was not working). I use Windows 7 and at the moment i've had Internet Explorer 8 and after a lot of failing updates to ie9 I've successfully install the Romanian version of IE9(now i have ie8 after a system restore). Then I installed the service pack 1. I've done a lot of things and I will try to enumerate them, but my problem persists. Settings from Yahoo Messenger and Internet Explorer are OK. I've try to reset winsock and ip from netsh. I've scanned my pc with spybot, mallwarebytes, Trojan Remover(simplysup), Loaris Trojan Remover, Avast, Nod32, Kaspersky, Bitdefender,alot of registry cleaner including CCleaner and maybe others that I cannot remember now. I reset the registry permissions using subinacl. At a moment my files permissions was set jut to "trusted installer" and I've put the permission back to files and folders using the model of other windows 7 machine. I have try so many things that now i'm stuck in a loop using different security tools to check for problems. Oh, and my virtual machines are working just fine.(I'm using VirtualBox) Please Help. PS, Reinstalling Windows is not an option. Thank you!

  Read the article

• Wake on Demand for Apache server in OS X 10.8

  - by Gary

  Mac OS X Mountain Lion does not have a Web Sharing box in the Sharing system prefs menu. It is thoroughly discussed on the web that the Apache server is available, and that it can be turned on manually in the command line, or by using a convenient Prefs Pane. That works while the computer is awake. But, when my computer goes to sleep, the server stops working, even though Wake for Network Access is checked in the Energy Saver Pref Pane. From the discussion on Bonjour, I see that this problem probably results from the fact that Apache isn't registered with Bonjour. Does that sound likely? If not, please make some suggestions. The connection is via hard-wired ethernet. If registration with Bonjour is the problem, I'd like to know how to register it. You gave a nice description of dns-sd, and the command description says dns-sd -R Name Type Domain Port [TXT...] (Register a service)", but I don't know what to use for "Name" or "Type", or the format of the domain. I tried some dns-sd -B searches and found nothing I could use as a model, and it doesn't show up in Bonjour Browser. Any suggestions would be appreciated.

  Read the article

• Compaq Motherboard gives "CPU Fan Error"

  - by John

  I have a motherboard for a HP business desktop dx5150 PC. The model written on the board is "MS-7050" and it is for an AMD socket 939 processor. I got everything installed in it, and when I turned it on, it showed a message stating that there was a "CPU Fan Error" (or some similar language) and then turned off. It never stays on for more than about 30 seconds, probably less. The fan had previously been working great, but I replaced it anyway with a brand new Cooler Master fan. This did not work. I then reset the BIOS with the jumpers on the board, no dice. I replaced the CMOS battery. Same error. I then replaced the entire computer power supply with a brand new Antec, same error. The fan header is keyed, and has room for 3 pins. The CPU fan is designed the same way, so its not that I'm missing a temperature sensor or anything. Can anyone give some suggestions? Especially maybe some secret keystrokes to bypass this error?

  Read the article

• datawind ubislate 9ci tablet computer hanging on boot

  - by user57924

  I am new to this forum. I purchased a new tablet Datawind Ubislate 9ci. It is a 9 inch no-bluetooth tablet. Details: Android 4.1.1 Rock chip RK2928 KERNEL linux version 3.0.36 I was trying to install CWM through mobile odin and ROM manager but my tablet was not supported so i downloaded build.prop editor from google play and changed it to some other cwm recognizable model viz. Samsung, nexus etc. When i was doing the above mentioned procedure, suddenly my tablet is coming up to bootloading and hanging there only and not opening i went to recovery and tried to do wipe data factory reset but failed to get opened after boot android system recovery(3e) has the following options 1)reboot system now 2)apply update from ADB 3)apply update from external storage 4)update rkimage from external storage 6)wipe data factory reset 7)wipe cache partition 8)recovery system from back up i tried to do wipe data factory reset 2-3 times but still hanging at boot i had not made any back up before this bootloop and also tried hard reset by pressing needle at the back please somebody help me to get rid of this problem and also tell me how to unlock bootloader thank you

  Read the article

• Unusable network, packet losses between router and NIC

  - by KáGé

  I have this setup: Gigabyte P35-DS3P motherboard Asus NX1101 PCI network card (the one on the motherboard got fried a few years ago by a power surge) Asus RT-N16 router Windows 7 x64 I think the other specs are irrelevant here, but I'll post them if you say so. Until a week ago everything was fine, but then my network became unusable: websites start loading but timeout before anything would come through (true for the web interface of the router as well), I can't reach the computer from my notebook and Windows' ping utility measures a ~50% packet loss between the computer and the router. Pinging localhost is good. The router works completely fine when wired to my notebook. I also tested different ports on the router, different cables, different router and connecting directly to the modem, but it's still the same. Sometimes it works for a few minutes right after turning on the machine, but then it becomes crap again, but mostly it's useless from the start. I've tried updating the firmware on the router, updating the driver for the network card (after which I started getting BSoDs in every 15 minutes), reinstalling Windows, swapping to Fedora 15 but none of them changed anything. Does this mean that the network card is dying, or could it be something else? If it's the card, what model do you recommend as a replacement? (Could be PCI or PCI-Ex x1) Thanks for your help.

  Read the article

• High fan speed with no reason

  - by Klaus

  For a few weeks, the fans of my Lenovo B590 laptop, running on Xubuntu 14, turn to high speed a few minutes after it is turned on. The fans won't speed down until I turn the computer off. This is quite strange, since This didn't happen before The temperatures are quite low (are they ?) $sensors Adapter: Virtual device temp1: +36.0°C (crit = +88.0°C) temp2: +30.0°C (crit = +126.0°C) coretemp-isa-0000 Adapter: ISA adapter Physical id 0: +37.0°C (high = +72.0°C, crit = +90.0°C) Core 0: +34.0°C (high = +72.0°C, crit = +90.0°C) Core 1: +31.0°C (high = +72.0°C, crit = +90.0°C) thinkpad-isa-0000 Adapter: ISA adapter fan1: 0 RPM pkg-temp-0-virtual-0 Adapter: Virtual device temp1: +37.0°C $sudo hddtemp /dev/sda /dev/sda: ST500LT012-9WS142: 33°C The computer is under low load: top - 08:30:15 up 16 min, 2 users, load average: 0.28, 0.23, 0.23 Tasks: 197 total, 1 running, 196 sleeping, 0 stopped, 0 zombie %Cpu(s): 0.8 us, 0.5 sy, 0.0 ni, 98.7 id, 0.0 wa, 0.0 hi, 0.0 si, 0.0 st KiB Mem: 3607944 total, 1973956 used, 1633988 free, 99660 buffers KiB Swap: 3744764 total, 0 used, 3744764 free. 789936 cached Mem The BIOS is up to date (and there are no fan settings in it) The fan is clean and dust-free Why would the BIOS turn the fans to high speed where there seem to be no reason for that ? It seems that we cannot control the fan manually with this model, so I guess the only solution is to understand why this happens.

  Read the article

• Is there any way to limit the turbo boost speed / intensity on i7 lap?

  - by Anonymous

  I've just got a used i7 laptop, one of these overheating pavilions from HP with quad cores. And I really want to find a compromise between the temp and performance. If I use linpack, or some other heavy benchmark, the temp easily gets to 95+, and having a TJ of 100 Degrees, for a 2630QM model, it really gets me throttling, that no cooling pad or even an industrial fan could solve. I figured later that it is due to turbo boost, and if I set my power settings to use 99% of the CPU instead of 100%, and it seems to disable the turbo boost, so the temp gets better. But then again it loses quite a bit of performance. The regular clock is 2GHz, and in turbo boost it gets to 2.6Ghz, but I just wonder if I could limit it to around 2.3Ghz, that would be a real nice thing. Also there is another question I've hard time getting answer to. It seems to me that clocks are very quickly boosting up to max even when not needed, eg, it's ok if the CPU has 0% load, the clocks get to their 800MHz, but even if it gets to about 5% it quickly jumps to a max and even popping up turbo, which seems very strange to me. So I wonder if there is any way to adjust the sensitivity of the Speed Step feature. I believe it would be more logical to demand increased clock if it hits let's say 50% load. I do understand that most of these features are probably hardwired somewhere in the CPU itself or the MB, which has no tuning options just like on many laptops. But I would appreciate if you could recommend some thing, or some software. Thanks

  Read the article

• A router that supports connecting with 2 different wifi networks

  - by Allan Deamon

  I Have the following setup in one place: We have a small local ISP through wireless. I have a external parabolic antenna, connected to a external usb wifi radio, connected through USB to a desktop old PC. The pc connects do the ISP wiki network, then do a Dial Up (PPPoE) connection through the this wifi setup. This will expand with others mobiles devices to be used. When I need, I take my home wireless router and connect though Ethernet in the PC, which is shares the internet. The problem is that the PC must be always ON and working. I would like to buy a wireless router which could be an AP to the mobile devices, notebooks, etc, as also could connect to the ISP Wifi/PPPoE network. So, this device must: Have one radio with detachable antenna to connect to the external antenna. It must connect as client to a network and then dial up the PPP Have another radio serving as AP (infrastructure) to the local place This can't be very expensive. I found a candidate: ( http://www.tp-link.com/en/products/details/?categoryid=1682&model=TL-WR2543ND ) It have 3 deatachable antennas, working with dual band. Officially, his firmware doesn't support it. My supposition: If internally there is 3 or 2 distinct wlan ports (like wlan0, wlan1), and there is support, i could use a OpenWRT, DD-WRT or Tomato to make this works. It also have 1 USB port, which I cold use to connect my actual USB Wifi card on it instead to the old PC. Another alternative, is a router that can do this out of box, with the original firmware. But I don't think this is a easy thing to find.

  Read the article

• Internet Troubles - PPPoE vs PPPoA?

  - by AkkA

  I have been having some internet troubles at home (ADSL2+ connection in Australia). We get random drop-outs from the authentication connection. It will keep the connection to the DSL service, but we lose authentication and either have to restart the router/modem (its combined, a Belkin one, not sure on model number) or unplug the phone cable, wait about 30 seconds and plug it in again. I've called the ISP (Telstra) a few times, but they only offer limited support when we dont use their supported hardware. Apparently something had happened on their side, they checked the box again (at least it sounded that simple), and told me it would be fine. It wasnt. I've replaced all the filters around the house, but that didnt help either. We do live a little bit away from the exchange (get a sync speed of about 3000/900), so I thought it could be due to line noise but that hasnt helped. Telstra allow both PPPoE and PPPoA connections (which I'm configuring through my router, dont have software on the PC side). I've been running PPPoA the whole time, would it make any difference changing it to PPPoE? If not, are there any other theories as to why we would be experiencing these drop-outs? It has been fine for at least 12 months, then suddenly started about 2 months ago.

  Read the article

• Why do I need a managed switch and which one should I buy?

  - by ascanio1

  I bought a 2nd router and I want both routers to have direct WAN access to the modem. One of the 2 routers directs VOIP traffic to a telephone line port. This VOIP service is provided by the cable carrier which also leases the modem & the router. The cable company technician told me that this VOIP line uses IPv6 addressing and therefore I must employ an IPv6 capable/compliant Giga Hub/Switch or my telephone line won't work anymore. Pls advise me (brand/model) an IPv6 compliant, 2 port, switch to purchase. Pls educate me: By reading this forum I thought that hubs broadcast traffic to all ports, regardless of which input/output is being used and so, theoretically, they have nothing to do with IP. Correct? Same story for unmanaged switches, where the only difference is that these latter devices route traffic only to those ports which are detected to be in use. Correct? I also understood that unmanaged switches route traffic simply by detecting hardware use and not by selecting specific IP traffic. Correct? Finally, there are managed switches which DO select traffic based on IP and, therefore, only these managed switches are involved with IPv6... Why would my cable company explicitly tell me, over and over, that I must use an IPv6 compliant switch? Why would they need a managed switch instead of an unmanaged one? Thanks in advance for helping me understand!

  Read the article

• Sharing music on NAS with other zunes and ipods

  - by osij2is

  After being a long time iPod owner, I'm switching to the new Zune with its subscription model. I haven't bought a Zune yet but I'm planning on doing so within the next month or so. I have approximately 40gb worth of music and my girlfriend has her iPod music library around 30gb. I've been trying to figure out how to migrate all our music off of our laptops/desktops and centralize everything on my NAS. In sharing iPod music isn't too bad. Sharing from one machine to all is fairly easy within the iTunes player. As far as storing all the music on a NAS, again, iPods aren't too bad and imagine other systems aren't difficult. But I'm really new to the Zune and I'm beginning to run into some issues. My questions are: Is it possible to store all music from our iPods and Zune subscriptions and share music between the iPod/Zune within the same file share on my NAS? I'm sure it's possible to store music on a share, but I'm not sure how iTunes and the Zune software differs. Is there 3rd party software, maybe something like DoubleTwist that can sync based from NAS to multiple desktop/laptops? I've never used DoubleTwist but it's something that I found that looks close to being what I need. I've never quite done this myself so I'm trying to find a solution that can: a) store music on a network share; b) sync between different devices (zune/ipod) seamlessly.

  Read the article

• Setting up VPN with Snow Leopard Server and Linksys router

  - by SueP

  I'd like to get VPN going so I can log in to the office securely from home. I'm using Snow Leopard machines everywhere, and currently have Airport Extremes set up at home and at the office. I have a mac mini with Snow Leopard Server that I'm going to move to the office to act as my server. I just bought a Linksys 4-port router because it says it does VPN (model RVS4000). My problem is, I don't have a clue how to set this thing up, and the more reading I do, the more confused I get. Do I need two of these routers, one at each end? My laptop and iPad claim they can do VPN, so I was assuming I only needed one VPN router? At this point, I literally don't know what questions to ask, or where to plug this thing in. Presumably, between the modem and the airport, but...? If somebody can walk me thru some really basic setup, I'd be very grateful. Right now, I feel like going outside and screaming for a while. But that might attract the local cougar, and after the prints I saw on the arena this afternoon, I don't want to draw its attention. :-)

  Read the article

• Imac g5 with no OS nor CD drive

  - by sinekonata

  What I want: Ubuntu on a g5 Imac. What I have: An empty PC (Intel g5 17" Imac) with broken CD drive. Its model is A1173. This PC with Ubuntu 12.04 and an old Vista partition. a usb flash drive. Problems: No CD means the only boot Drive I could use is USB. There are no BIOS on Macs so I can't set boot settings or even see if it detects my USB drive. When I start the machine and press ALT the first and only thing I see is an old corrupted winXP partition and not a single option or additional information. So assuming blindly that the Mac hardware/firmware works normally, I don't have any Mac OS to use any of the tools that I found on different tutorials for building a bootable .img drive for macs. I can't find much software on Linux/Windows to substitute to those tools, for example among others converting an .iso file (win/linux) to .img (mac I guess). Which makes me think that the scenario where someone like me has Mac hardware but no Mac OS is extremely rare. So other than finding someone that has a Mac I have no solution. So I ask what would you do? the only thing is it should not involve any money (I know mac soft is rarely free) which also excludes getting any MacOS unless I can use a free macos.img for VM or restore the original Mac for free. Thank you

  Read the article

• Almost All Xenserver Logical Volumes Disappeared - Recovery?

  - by Alex

  We had a hard disc crash of one of two hard discs in a software raid with a LVM on top. The server is running Citrix xenserver. On the hard disk which is still intact, the volume group gets detected well, but only one LV is left. (some hashes replaced by "x") # lvdisplay --- Logical volume --- LV Name /dev/VG_XenStorage-x-x-x-x-408b91acdcae/MGT VG Name VG_XenStorage-x-x-x-x-408b91acdcae LV UUID x-x-x-x-x-x-vQmZ6C LV Write Access read/write LV Status available # open 0 LV Size 4.00 MiB Current LE 1 Segments 1 Allocation inherit Read ahead sectors auto - currently set to 256 Block device 253:0 root@rescue ~ # vgdisplay --- Volume group --- VG Name VG_XenStorage-x-x-x-x-408b91acdcae System ID Format lvm2 Metadata Areas 1 Metadata Sequence No 4 VG Access read/write VG Status resizable MAX LV 0 Cur LV 1 Open LV 0 Max PV 0 Cur PV 1 Act PV 1 VG Size 698.62 GiB PE Size 4.00 MiB Total PE 178848 Alloc PE / Size 1 / 4.00 MiB Free PE / Size 178847 / 698.62 GiB VG UUID x-x-x-x-x-x-53w0kL I could understand if a full physical volume is lost - but why only the logical volumes? Is there any explanation for this? Is there any way to recover the logical volumes? EDIT We are here in a rescue system. The problem is that the whole server does not boot (GRUB error 22) What we are trying to do is to access the root filesystem. But everything was in the LVM. We have only this: (parted) print Model: ATA SAMSUNG HD753LJ (scsi) Disk /dev/sdb: 750GB Sector size (logical/physical): 512B/512B Partition Table: msdos Number Start End Size Type File system Flags 1 32.3kB 750GB 750GB primary boot, lvm And this 750GB LVM volume is exactly what we see on top. edit2 Output of vgcfgrestore, but from the rescue system, as there is no root to chroot to. # vgcfgrestore --list VG_XenStorage-x-b4b0-x-x-408b91acdcae File: /etc/lvm/archive/VG_XenStorage-x-x-x-x-408b91acdcae_00000.vg VG name: VG_XenStorage-x-x-x-x-408b91acdcae Description: Created *before* executing '/sbin/vgscan --ignorelockingfailure --mknodes' Backup Time: Fri Jun 28 23:53:20 2013 File: /etc/lvm/backup/VG_XenStorage-x-x-x-x-408b91acdcae VG name: VG_XenStorage-x-x-x-x-408b91acdcae Description: Created *after* executing '/sbin/vgscan --ignorelockingfailure --mknodes' Backup Time: Fri Jun 28 23:53:20 2013

  Read the article

• How do I push my initial snapshot to a subscriber server in SQL Server 2000?

  - by Kev

  I'm configuring Transactional Replication using the Push model. The scenario is: The SQL Servers: SQL01 (publisher) and SQL02 (subscriber) - both running SQL 2000 SP4. Both servers are standalone (i.e. not domain members) Both servers have their FQDN and NETBIOS names in their HOSTS files I've managed to configure SQL01 to publish my database and configured a Push subscription for SQL02 using the Push New Subscription wizard and set the Distribution Agent to update the subscription continuously. On the Push Subscription wizard "Initialise Subscription" page I've selected "Yes, initialise the schema and data" and ticked the "Start the Snapshot Agent to begin the initialisation process immediately" option. All the required services are running (SQL Agent). When I complete the wizard and browse the Replication - Publications folder I can see my publication (blue book with arrow). The publication shows the Push subscription and its status is Pending. If I look in the c:\Program Files\Microsoft SQL Server\Mssql\Repldata folder I see a number of T-SQL scripts for each table e.g. Products.bcp, Products.sch, Products.idx. What should happen now? Should my replicated database now (magically) appear on the subscription server?

  Read the article

• why does the partition start on sector 2048 instead of 63

  - by gcb

  I had two drives partitioned the same and running 2 raid partitions on each. One died and I replaced it under warranty for the same model. While trying to partition it, the first partition can only start on sector 2048, instead of 63 that was before. Driver have different geometry as previous and remaining ones. (Fewer heads/more cylinders) old drive: $ sudo fdisk -c -u -l /dev/sdb Disk /dev/sdb: 2000.4 GB, 2000398934016 bytes 255 heads, 63 sectors/track, 243201 cylinders, total 3907029168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000aa189 Device Boot Start End Blocks Id System /dev/sdb1 * 63 174080339 87040138+ 83 Linux /dev/sdb2 174080340 182482334 4200997+ 82 Linux swap / Solaris /dev/sdb3 182482335 3907024064 1862270865 fd Linux raid autodetect remanufactured drive received from warranty: $ sudo fdisk -c -u -l /dev/sda Disk /dev/sda: 2000.4 GB, 2000398934016 bytes 81 heads, 63 sectors/track, 765633 cylinders, total 3907029168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000d0b5d Device Boot Start End Blocks Id System /dev/sda1 2048 ... why is that?

  Read the article

• Short, intermittent USB port timeouts

  - by jacobsee

  I have a data acquisition application controlled by a Windows PC. I am using an Intel Desktop Board DH67CL motherboard. This has 6 USB2 ports along with 2 of the new blue USB3 ports. The DAQ instrument connects via USB to the computer. Roughly once every day or two there is a short communication glitch with the USB that causes the instrument to disconnect briefly and then reconnect. This is logged so I know whenever it happens. Occasionally it will cause the data acquisition to stop. I've verified that the glitches will go away if I use the USB3 ports, or if I use a PCI add-on card with USB ports. So it seems that there is something going on with these built-in USB2 ports on this motherboard. I haven't yet had a chance to test with other motherboards. My question: what could be causing these glitches and how to get rid of them for this board, or is there a better motherboard to use? We have standardized on the DH67CL because it's inexpensive, has 3 PCI slots that we need, and is readily available. We don't need the power of higher-end server boards but reliability is important. Thanks. Update: This problem has been reproduced many times on different hardware, though we always use the same model of motherboard (DH67CL) and power supply (Antec EA-430D). I don't think the power requirements are very high but will check on that.

  Read the article

• Use external display from boot on Samsung laptop

  - by OhMrBigshot

  I have a Samsung RV511 laptop, and recently my screen broke. I connected an external screen and it works fine, but only after Windows starts. I want to be able to use the external screen right from boot, in order to set the BIOS to boot from DVD, and to then install a different OS and also format the hard drive. Right now I can only use the screen when Windows loads. What I've tried: I've tried opening up the laptop and disconnecting the display to make it only find the external and use the VGA as default -- didn't work. I've tried using the Fn+key combo in BIOS to connect external display - nothing I've been looking around for ways to change boot sequence without entering BIOS, but it doesn't look like it's possible. Possible solutions? A way to change boot sequence without entering BIOS? Someone with the same brand/similar model to help me blindly keystroke the correct arrows/F5/F6 buttons while in BIOS mode to change boot sequence? A way to force the external display to work from boot, through modifying the internal connections (I have no problem taking the laptop apart if needed, please no soldering though), through BIOS or program? Also, if I change boot sequence without accessing external screen, would the Ubuntu 12.1 installation sequence attempt to use the external screen or would I only be able to use it after Linux is installed and running? I'd really appreciate help, I can't afford to fix the screen for a few months from now, and I'd really like to make my computer come back to decent performance! Thanks in advance!

  Read the article

• What are the IR codes the new Apple Remote (alu) uses?

  - by index

  I would like to clone the new Apple Remote (infrared, second generation, aluminium) just for fun with a microcontroller. Most codes of the previous model can be found in the LIRC remote control database (all except the key combinations menu + <<,play, which unpair, change ID, pair the remote. I also don't know which bit encodes the battery status. It uses a modified 32 bit NEC protocol (reverse LIRC codes bytewise). But the new Apple remote uses two additional codes for the play and the new select button. I don't have a mac, so I can't brute force test codes either ;-) So if someone possesses such a remote and the ability of recording those two new buttons and three combinations I'd really appreciate it. If you can't run LIRC (or it gets confused by the new codes) and you don't have an oscilloscope or logic analyser, maybe you could hook up a photo diode to your sound input and record the codes with Audacity? Just hit record, hit each button and combo a few times, hit stop, upload the uncompressed WAV file to a sharing site, done. That'd be great!

  Read the article

• dell latitude XT touch screen issue

  - by Jake

  yesterday I installed windows 7 ultimate after I had the enterprise version on this machine for a few months. the installation went smoothly and everything worked fine except for the finger detection of the screen(only the pen worked) and the bottom screen buttons for rotating and so. so I started to install all the missing drivers dell recommends for this model on their site, but once I tried to install N-Trig degitizer driver the installation said it was unsuccessful and since then the touch stopped working completely! I tried system restore but it didn't help so I went on and formatted the harddisk completely once again and installed windows but that didn't work either. I tried to install the N-Trig's driver but it was alarting for a fatal error and said that no device was detected. same story with N-Trig rollback. so I checked the device manager and saw an "unknown device" with VID and PID values set as 0000. I figured the N-Trig driver might have messed with the device firmware or something and now it doesnt know it's ID and munufactor... Is there anything that can be done? like forcing the N-Trig driver to install on this device or something? please help!

  Read the article

• Shoretel Upgrade Path

  - by Brian

  I currently have a Shoretel Server running Server 2003 x32 as a virtual machine paired with a ShoreGear 90 switch and another unused switch of the same model being reserved for manual failover. I am getting the software mailed to me from my partner, but with limited support since the server is in a relatively remote area. I am tempted to upgrade the OS at the same time as performing the upgrade, but want to know if there are any horror stories or advice I should know about before diving in. I'm upgrading from Shoretel 9.2 Build. I will be upgrading first to version 10.1 then finally to 11.1. The system has been bullet proof since it was installed and we are upgrading mainly to get a client that is a little more modern. My question boils down to: Should I even bother with an OS upgrade or even possibly a fresh install of Windows with an install of Shoretel 11.1 and just transfer the configuration? Should I just stay with Server 2003 since it is supported in my target version of Shoretel and the upgrade will be more than enough to keep me busy as a novice?

  Read the article

• how can i move ext3 partition to the beginning of drive without losing data?

  - by Felipe Alvarez

  I have a 500GB external drive. It had two partitions, each around 250GB. I removed the first partition. I'd like to move the 2nd to the left, so it consumes 100% of the drive. How can this be accomplished without any GUI tools (CLI only)? fdisk Disk /dev/sdd: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0xc80b1f3d Device Boot Start End Blocks Id System /dev/sdd2 29374 60801 252445410 83 Linux parted Model: ST350032 0AS (scsi) Disk /dev/sdd: 500GB Sector size (logical/physical): 512B/512B Partition Table: msdos Number Start End Size Type File system Flags 2 242GB 500GB 259GB primary ext3 type=83 dumpe2fs Filesystem volume name: extstar Last mounted on: <not available> Filesystem UUID: f0b1d2bc-08b8-4f6e-b1c6-c529024a777d Filesystem magic number: 0xEF53 Filesystem revision #: 1 (dynamic) Filesystem features: has_journal dir_index filetype needs_recovery sparse_super large_file Filesystem flags: signed_directory_hash Default mount options: (none) Filesystem state: clean Errors behavior: Continue Filesystem OS type: Linux Inode count: 15808608 Block count: 63111168 Reserved block count: 0 Free blocks: 2449985 Free inodes: 15799302 First block: 0 Block size: 4096 Fragment size: 4096 Blocks per group: 32768 Fragments per group: 32768 Inodes per group: 8208 Inode blocks per group: 513 Filesystem created: Mon Feb 15 08:07:01 2010 Last mount time: Fri May 21 19:31:30 2010 Last write time: Fri May 21 19:31:30 2010 Mount count: 5 Maximum mount count: 29 Last checked: Mon May 17 14:52:47 2010 Check interval: 15552000 (6 months) Next check after: Sat Nov 13 14:52:47 2010 Reserved blocks uid: 0 (user root) Reserved blocks gid: 0 (group root) First inode: 11 Inode size: 256 Required extra isize: 28 Desired extra isize: 28 Journal inode: 8 Default directory hash: half_md4 Directory Hash Seed: d0363517-c095-4f53-baa7-7428c02fbfc6 Journal backup: inode blocks Journal size: 128M

  Read the article

< Previous Page | 533 534 535 536 537 538 539 540 541 542 543 544  | Next Page >