Search Results

Search found 19279 results on 772 pages for 'everything'.

Page 539/772 | < Previous Page | 535 536 537 538 539 540 541 542 543 544 545 546  | Next Page >

  • CPU temperatures high on new build after gaming

    - by Reznor
    My friend had a problem with his computer a while back. His games were crashing, even within the menus. He was stumped as to what the problem was, so I posted on here requesting help. He found out the day later, when his computer would start up but wouldn't display anything on the screen. His video card must have came screwed up. So, he got a replacement. Now, there's a new problem. His temperatures, which were acceptable before, are now insanely high. His GPU temperature runs 70-80c, which is understandable considering he's running his games maxed out, but the real problem here is his processor and motherboard temperatures. All four of his cores are running at 88-90c after coming out of a game. His motherboard temperature was also 70c at one point. In terms of cooling, his case should definitely be adequate. He has an Antec Twelve Hundred. He's using stock fans. The cable management in his case is very good; better than average. He's using the stock heatsink with the processor too, but note, it was fine before the replacement, so it isn't like there's some inherent problem. He has checked the case too. Everything's fine! No cables in the way. The heatsink is seated properly. He turned his case fans up to high, as well, but the temperatures are persisting. Could the processor be overheating due to running games maxed out? Any ideas?

    Read the article

  • BIOS and Windows cannot detect CDROM device

    - by eman
    Hello! I have a HL-DT-ST RW/DVD GCC-4521B dvdrom device and a big problem. Some days ago everything worked fine. A friend installed some software and then the drives in winxp has been marked as corrupt. I uninstalled the software, but still corrupt drives. The next step I have done was running the current software GCC-4521B101(E).exe. When I ran this software again, the drives was automatically updated, but still marked as corrupt (in the Device Manager), even if I did a reboot. And then the big mistake: once more I tried to run this software, but during the update process, the machine restarted and boom! The DVDROM device doesn't work anymore. The led doesn't blink and if I push the eject button, nothing happens. Also bios and winxp doesn't recognize the optical drive. Then I plugged an other optical drive and it worked, but my old drive seems to be dead. So, what happened and how to solve this problem? Please help. Regards!

    Read the article

  • IIS 7, FastCGI, PHP and custom php.ini files

    - by Marlon
    I'm running PHP 5.3, FastCGI, and IIS 7 on Windows Server 2008. I have a site which I would like to configure its own php.ini settings for but things aren't working as expected. I am following the tutorial located here. This is what I have done so far: 1) Configured a new website with it's own AppPool. 2) Selected PHP 5.3.6 from the PHP Manager available on the website home on IIS (not the web server home which sets the global version of PHP) 3) Added the following lines to the section of the applicationHost.config file located at system32/inetsrv/config <application fullPath="C:\Program Files (x86)\PHP\v5.3\php-cgi.exe" arguments="-d open_basedir=C:\inetpub\wwwroot\kickasswebsite.com" maxInstances="4" idleTimeout="300" activityTimeout="30" requestTimeout="90" instanceMaxRequests="200" protocol="NamedPipe" queueLength="1000" flushNamedPipe="false" rapidFailsPerMinute="10"> <environmentVariables> <environmentVariable name="PHPRC" value="c:\inetpub\wwwroot\kickasswebsite.com" /> </environmentVariables> </application> 4) I then create a php.ini file located in C:\inetpub\wwwroot\kickasswebsite.com (the location of the root of the website) register_globals = on 5) I then run test.php which simply outputs everything the method call to phpinfo() returns. At this point, I observe that the global setting for register_globals = off (as it should be), but the local setting for register_globals = off, even though I specified it differently in the php.ini file I created at the root of the site. Furthermore, I see these settings in the output of the php.ini Configuration File (php.ini) Path C:\Windows Loaded Configuration File C:\Program Files (x86)\PHP\v5.3\php.ini Scan this dir for additional .ini files (none) Additional .ini files parsed (none) What am I messing up on, or is there a different way to go about this?

    Read the article

  • How do I Forward root's email to an external email address?

    - by ErebusBat
    I have a small server (Ubuntu 10.04) at my house and I would like to forward root's email to my gmail hosted domain to get security notifications and what not. I ripped everything out and started from scratch and ran into some other issues. I now have sendmail working in the sense that I can mail [email protected] and get the mail. HOWEVER, adding an address to /root/.forward does not actually forward the message. I get the following in my logs: Dec 22 14:04:37 batcave sendmail[4695]: oBML4bAT004695: to=<root@batcave>, ctladdr=aburns (1000/1000), delay=00:00:00, xdelay=00:00:00, mailer=relay, pri=30075, relay=[127.0.0.1] [127.0.0.1], dsn=2.0.0, stat=Sent (oBML4bJ9004696 Message accepted for delivery) Dec 22 14:04:39 batcave sm-mta[4698]: STARTTLS=client, relay=[69.145.248.18], version=TLSv1/SSLv3, verify=FAIL, cipher=DES-CBC3-SHA, bits=168/168 Dec 22 14:04:40 batcave sm-mta[4698]: oBML4bJ9004696: to=<[email protected]>, ctladdr=<[email protected]> (1000/1000), delay=00:00:03, xdelay=00:00:03, mailer=relay, pri=120336, relay=[69.145.248.18] [69.145.248.18], dsn=2.0.0, stat=Sent (OK 01/D4-00853-216621D4) You can see where my local sendmail instance accepts it then hands it off to my ISP, but with the wrong address ([email protected]).

    Read the article

  • How to prevent Gnome-shell's Alt+Tab from grouping windows from similar apps?

    - by wleoncio
    I love pretty much everything about how Gnome Shell handles app-switching through Alt+Tab. My one gripe with it, though, is how it forces the user to use Alt+` to switch between windows of the same app. This is very annoying for me, because now I have to keep in mind if the last window I was using belonged to the same app as the current window or not. Definitely a nuisance for power users who thinks in terms of "windows I'm working with" instead of "applications I'm working on". I've tried the AlternateTab extension ( https://extensions.gnome.org/extension/15/alternatetab/ ), but it's looks way too ugly for me. Not to mention that in the end all I want is to remap Alt+(key above tab) to Alt+Tab on this application. I guess one option would be to just tweak Gnome-shell. My guess is that I should tinker with the altTab.js file at /usr/share/gnome-shell/js/ui/, but the file is too long and overwhelming for someone like me, who doesn't know JavaScript. Does anyone know how I can make Gnome Shell stop grouping windows by applications?

    Read the article

  • Effects of internet connection speeds on server queries

    - by SephMerah
    Can my internet connection significantly effect queries run on phpmyadmin? I am currently 18 down and 30 up. I switched internet connections today and noticed a deep drop in query performance. The query that I am running is SELECT * FROM table. Simple. The table has one row of data. The MySQL server is on the same server as everything else. It is a VPS. Godaddy hosts. I dont have any other information. Centos 6.3 MySQL 5.1 PhpMyAdmin 3.4 Okay used google tools to inspect the XHR going out and coming in and this is what it reported. {"success":true,"message":"<div class=\"success\">Your SQL query has been executed successfully ( Query took 0.0033 sec )<\/div>","sql_query":"<div id=\"result_query\" align=\"\">\n<div class=\"success\">Your SQL query has been executed successfully ( Query took 0.0033 sec ) SNIP..................."}. So apparently my server is fine. The strange thing is though.. The returned XHR comes back exactly as soon as I execute the query on the page. It comes back within less than a second. Why PhpMyadmin does not report the change immediately. I am going to try a re-install.

    Read the article

  • nginx: Rewrite PHP does not work

    - by Ton Hoekstra
    I've a Suffix Proxy installed and I'm using the following rewrite with wildcard subdomain DNS on: location / { if (!-e $request_filename) { rewrite ^(.*)$ /index.php last; break; } } My suffix proxy has the following URL format: (subdomain and/or domain + domain extension to proxy).proxy.org/(request-uri to proxy) I've this php code in my index.php: if(preg_match('#([\w\.-]+)\.example\.com(.+)#', $_SERVER['SERVER_NAME'].$_SERVER['REQUEST_URI'], $match)) { header('Location: http://example.com/browse.php?u=http://'.$match[1].$match[2]); die; } But when requested a page with a .php extension I'll get a 404 not found error: http://www.php.net.proxy.org/docs.php - HTTP/1.1 404 Not Found http://www.utexas.edu.proxy.org/learn/php/ex3.php - HTTP/1.1 404 Not Found But everything else is working (also index.php is working): http://php.net.proxy.org/index.php - HTTP/1.1 200 OK http://www.php-scripts.com.proxy.org/php_diary/example2.php3 - HTTP/1.1 200 OK http://www.utexas.edu.proxy.org/learn/php/ex3.phps - HTTP/1.1 200 OK http://www.w3schools.com.proxy.org/html/default.asp - HTTP/1.1 200 OK Somebody has an answer? I don't know why it's not working, on apache it's working fine. Thanks in advance. I've removed the location and now it's working perfectly: if (!-e $request_filename) { rewrite ^(.*)$ /index.php last; break; }

    Read the article

  • Microsoft Office 2003 applications crash on 'Save As' to a network mapped drive

    - by Archit Baweja
    Hey guys, so I'm not sure if it belongs on ServerFault forums so figured I'd ask here first because its a workstation/client side issue. I have a client where we have windows server 2003 setup, with windows xp professional setup on all the workstations. We've setup a 'domain' and all workstations logon to the domain (authenticated by the Windows Domain Controller), and in the logon script we map drives on to each workstation. Everything is working peachy except for one workstation, where when I open a file in excel from a mapped drive, it opens fine, but when I go to hit Save As, the Save As dialog pops and hangs up. I cannot perform any other action in excel. When I try cancel the Save As dialog, excel crashes. The mapped drive opens up fine in Windows Explorer. To further investigate this issue, I created a new blank text document on the network drive in Windows Explorer. I then opened it. Then hit save as, and the Save As dialog opened up fine and it would let me save the document. I repeated the above steps for a word document. However this time the Save As dialog hung/froze again. So I'd imagine its a Microsoft Office Issue. Any ideas?

    Read the article

  • Printing special / extended characters on web page - Firefox or printer issue?

    - by edmicman
    My dad brought this to my attention and I'm looking into it, but thought I'd post here and see if anyone has any ideas... He's running Win7, using Firefox and printing to a wireless connected Brother HL-2170W printer. He's got a web page (http://cornandsoybeandigest.com/inputs/fertilizer/applying-nitrogen-after-planting-0512/index.html) that has extended/special characters in it - the funny "a" in Fernandez. The characters show correctly in Firefox on the page. He printed it, and the extended "a" printed as a diamond with a question mark. He says it shows that way in the print preview, too. I pulled up the same page in Ubuntu, Firefox, and it displayed in my print preview and physically printed everything correctly. I just checked on my wife's Win7 PC in Firefox and the print preview looked correct on her system, too. We have a Brother 2040 here. Soooo, my question is, is this possibly a problem in the browser somehow, or the printer driver? I'm leaning towards the printer driver now, but I can't say I've run into this before. Is it a setting somewhere? I just installed this printer for him the other day, using the CD that came with it; I could try updating the driver from Brother's website I guess. Is there anything else I should look at or check? Thanks!

    Read the article

  • Varnish does not start properly (crashes after startup) with no error messages

    - by Matthew Savage
    I am running Varnish (2.0.4 from the Ubuntu unstable apt repository, though I have also used the standard repository) in a test environment (Virtual Machines) on Ubuntu 9.10, soon to be 10.04. When I have a working configuration and the server starts successfully it seems like everything is fine, however if, for whatever reason, I stop and then restart the varnish daemon it doesn't always startup properly, and there are no errors going into syslog or messages to indicate what might be wrong. If I run varnish in debug mode (-d) and issue start when prompted then 7 times out of time it will run, but occasionally it will just shut down 'silently'. My startup command is (the $1 allows for me to pass -d to the script this lives in): varnishd -a :80 $1 \ -T 127.0.0.1:6082 \ -s malloc,1GB \ -f /home/deploy/mysite.vcl \ -u deploy \ -g deploy \ -p obj_workspace=4096 \ -p sess_workspace=262144 \ -p listen_depth=2048 \ -p overflow_max=2000 \ -p ping_interval=2 \ -p log_hashstring=off \ -h classic,5000009 \ -p thread_pool_max=1000 \ -p lru_interval=60 \ -p esi_syntax=0x00000003 \ -p sess_timeout=10 \ -p thread_pools=1 \ -p thread_pool_min=100 \ -p shm_workspace=32768 \ -p thread_pool_add_delay=1 and the VCL looks like this: # nginx/passenger server, HTTP:81 backend default { .host = "127.0.0.1"; .port = "81"; } sub vcl_recv { # Don't cache the /useradmin or /admin path if (req.url ~ "^/(useradmin|admin|session|sessions|login|members|logout|forgot_password)") { pipe; } # If cache is 'regenerating' then allow for old cache to be served set req.grace = 2m; # Forward to cache lookup lookup; } # This should be obvious sub vcl_hit { deliver; } sub vcl_fetch { # See link #16, allow for old cache serving set obj.grace = 2m; if (req.url ~ "\.(png|gif|jpg|swf|css|js)$") { deliver; } remove obj.http.Set-Cookie; remove obj.http.Etag; set obj.http.Cache-Control = "no-cache"; set obj.ttl = 7d; deliver; } Any suggestions would be greatly appreciated, this is driving me absolutely crazy, especially because its such an inconsistent behaviour.

    Read the article

  • CIFS Mounting Permissions

    - by malco
    I have an issue that I;m going round in circles with, I hope you can help. The Set up: Server 1 (CIFS Client) - CentOS 6.3 AD integrated uing Samba/Winbind & idmap_ad Server 2 (CIFS Server) - CentOS 6.3 AD integrated uing Samba/Winbind & idmap_ad All users (apart from root) are AD authenticated and this, including groups, etc works happily. What's working: I have created a share on Server 2: [share2] path = /srv/samba/share2 writeable = yes Permissions on the share: drwxrwx---. 2 root domain users 4096 Oct 12 09:21 share2 I can log into a Windows machine as user5 (member of domain users) and everything works as it should, for example: If I create a file it shows the correct permissions and attributes on both the MS and the Linux sides. Where I Fall Down: I mount the share on Server 1 using: # mount //server2/share2 /mnt/share2/ -o username=cifsmount,password=blah,domain=blah Or using fstab: //server2/share2 /mnt/share2 cifs credentials=/blah/.creds 0 0 This mounts fine, but.... If I log su, or log onto server 1 as a normal user (say user5) and try to create a file I get: #touch test touch test touch: cannot touch `test': Permission denied Then if I check the folder the file was created but as the cifsmount user: -rw-r--r--. 1 cifsmount domain users 0 Oct 12 09:21 test I can rename, delete, move or copy stuff around as user5, I just can't create anything, what am I doing wrong? I'm guessing it's something to do with the mount action as when I log onto server2 as user5 and access the folder locally it all works as it should. Can anyone point me in the right direction?

    Read the article

  • How to track which process is failing logons?

    - by Massimo
    Windows Server 2003, VMWare VirtualCenter 2.5. Something is continuously trying to log on to VirtualCenter using a disabled domain account; the failed logon attempts are logged by VirtualCenter in its own logs and by Windows in the Security event log. This happens roughly every minute or two. The source of the logon attempts is 127.0.0.1, so it must be some process running on the server itself. There are no services running as this user account and no scheduled jobs on the system. The task manager doesn't show any proces running under this account, either. The user account's name is nowhere to be found in the Registry. But some process is trying to use it, and failing. It probably is not some critical process, as everything looks fine; it could be something that was installed long ago and forgotten there. Whatever it is, it probably is running under another user account (possibly a system one), but is trying to log on to VC using those credentials, which are probably saved in some configuration file, since they're not stored in the Registry. How can I track which process is trying (and failing) those logon attempts, either using Windows or VirtualCenter?

    Read the article

  • HP tx2510us shuts down without warning, now won't boot, no BIOS codes, screen doesn't light

    - by Tim S
    Hey all, HP tx2150us worked great for a year and a half, rarely it would shut down instead of sleeping. It started running hot sometimes, I installed Win7, worked great, still running hot. Before Xmas, it gave me evidence of video errors - jagged lines, rows missing. That same night, it started rebooting, then it shut off and wouldn't boot. It gave me a BIOS code, I shut it off to look up the code online. When I turned it on again, it won't boot at all. The LEDs all light up, the fan, HD, and optical all spin up, but the screen never lights up and it doesn't try to boot, nor does it blink any BIOS codes. It just acts like it's sleeping, and won't wake up. I suspected heat problems, so I disassembled it, cleaned the crap out of the fan, and reassembled it, breaking the stereo mic connector. Oh well. When I reassembled it, it booted up into Win7 again, but kept shutting down for no discernible reason. After a dozen or so random reboots like that, it is now back to where it was - turns on but doesn't boot or give BIOS codes. The screen never lights, and everything spins up then idles. Any ideas? I really can't afford to buy a new one and I use(d) it to take ALL my notes, that's why I got a tablet in the first place.

    Read the article

  • Max. Temp. on Intel Burn Test for Stock Dell Precision T3500

    - by HK1
    I'm troubleshooting an issue on a Dell Precision T3500. As part of my troubleshooting I've decided to try running a stress test using Intel Burn Test software. This machine is a stock configuration with 12GB of RAM and a Xeon W3670 processor (nothing overclocked). When I run IBT using the standard mode, SpeedFan reports a processor temperature in excess of 80C. I've seen numbers as high as 90C but even at that temperature the machine does not become unstable or crash. However, it seems way too high. This processor has a TCase of 67.9C according to Intel's website. I'm guessing that means I'm in the danger zone any time I go over that temperature. I've checked the cooling system and everything looks fine. I've even took out the heat sink and reinstalled it with new thermal compound. This did not appear to make the problem better or worse. Is there a discrepancy somewhere here in the way temperatures are measured or displayed? I've also tried using HWMonitor from CPUID and it reports the same temperatures. Should I just let the Standard Test go and disregard the temperature outputs?

    Read the article

  • OS X (10.6) Apache Sudden Death, Nginx not working either...

    - by Jesse Stuart
    Hi, I turned on my computer today and apache wasn't working. This is weird as its been working for the last 6 months without issue. The only thing I did which may of caused a problem, is I uninstalled a bunch of gems. This shouldn't be the issue though as apache doesn't rely on gems. I decided to give nginx a try to see if it would work and have the exact same issue. The symtoms are: I go to http://localhost and get the browsers default 404 page (not rendered by apache/nginx) No error is found anywhere (I checked all logs) Apache is rinning (also tried with Nginx) How can I debug this to find the root of the problem? I can't think of why this would be happening. I've tried repairing permissions in case this was the issue, apparently it wasn't. Everything was working the other day, and nothing changed in the apache config. Update: Here is the output of telnet localhost 80 $ telnet localhost 80 Trying ::1... telnet: connect to address ::1: Connection refused Trying fe80::1... telnet: connect to address fe80::1: Connection refused Trying 127.0.0.1... telnet: connect to address 127.0.0.1: Connection refused telnet: Unable to connect to remote host

    Read the article

  • ssh Prompts For Password After Account Unlocked - Despite ssh key?

    - by user1011471
    Here's what happened: I set up ssh key so that user could ssh from A to B without a password. I got user's password wrong in some other context too many times, and user's account got locked out. (IT uses Active Directory here) IT unlocked the account. Concurrent to the unlocking, a script was running, calling something like ssh user@B some-health-check-command every 5 seconds or so -- which seemed to work fine before I caused user to get locked out in step 2. IT reports user reliably gets locked out a short time after each unlock attempt. I thought the ssh key would allow ssh user@B some-command as long as the account is not locked. But it behaves as if, when user gets unlocked, B suddenly asks for a password and since my command repeatedly runs without supplying a password, the account gets locked out after 5 attempts. Account cannot be accessed at this time. Please contact your system administrator. My questions are... Is that what's happening? Or: what's happening? More importantly: How can I reconfigure things such that my script doesn't cause problems? Can I accomplish what I want without having to install Expect? (I don't know if I have permission to do so) Other notes: Not using ssh-agent currently. The ssh command is running on our Jenkins master, a linux box. A and B are Mac OS X. user is managed in Active Directory and normally can sign into all three machines. Other than these things and the ssh key I set up, everything else has the default configuration as far as I know.

    Read the article

  • Almost All Xenserver Logical Volumes Disappeared - Recovery?

    - by Alex
    We had a hard disc crash of one of two hard discs in a software raid with a LVM on top. The server is running Citrix xenserver. On the hard disk which is still intact, the volume group gets detected well, but only one LV is left. (some hashes replaced by "x") # lvdisplay --- Logical volume --- LV Name /dev/VG_XenStorage-x-x-x-x-408b91acdcae/MGT VG Name VG_XenStorage-x-x-x-x-408b91acdcae LV UUID x-x-x-x-x-x-vQmZ6C LV Write Access read/write LV Status available # open 0 LV Size 4.00 MiB Current LE 1 Segments 1 Allocation inherit Read ahead sectors auto - currently set to 256 Block device 253:0 root@rescue ~ # vgdisplay --- Volume group --- VG Name VG_XenStorage-x-x-x-x-408b91acdcae System ID Format lvm2 Metadata Areas 1 Metadata Sequence No 4 VG Access read/write VG Status resizable MAX LV 0 Cur LV 1 Open LV 0 Max PV 0 Cur PV 1 Act PV 1 VG Size 698.62 GiB PE Size 4.00 MiB Total PE 178848 Alloc PE / Size 1 / 4.00 MiB Free PE / Size 178847 / 698.62 GiB VG UUID x-x-x-x-x-x-53w0kL I could understand if a full physical volume is lost - but why only the logical volumes? Is there any explanation for this? Is there any way to recover the logical volumes? EDIT We are here in a rescue system. The problem is that the whole server does not boot (GRUB error 22) What we are trying to do is to access the root filesystem. But everything was in the LVM. We have only this: (parted) print Model: ATA SAMSUNG HD753LJ (scsi) Disk /dev/sdb: 750GB Sector size (logical/physical): 512B/512B Partition Table: msdos Number Start End Size Type File system Flags 1 32.3kB 750GB 750GB primary boot, lvm And this 750GB LVM volume is exactly what we see on top. edit2 Output of vgcfgrestore, but from the rescue system, as there is no root to chroot to. # vgcfgrestore --list VG_XenStorage-x-b4b0-x-x-408b91acdcae File: /etc/lvm/archive/VG_XenStorage-x-x-x-x-408b91acdcae_00000.vg VG name: VG_XenStorage-x-x-x-x-408b91acdcae Description: Created *before* executing '/sbin/vgscan --ignorelockingfailure --mknodes' Backup Time: Fri Jun 28 23:53:20 2013 File: /etc/lvm/backup/VG_XenStorage-x-x-x-x-408b91acdcae VG name: VG_XenStorage-x-x-x-x-408b91acdcae Description: Created *after* executing '/sbin/vgscan --ignorelockingfailure --mknodes' Backup Time: Fri Jun 28 23:53:20 2013

    Read the article

  • NTFS 'Owner' missing when accessing hard disk from external USB adapter

    - by trismarck
    I have a hard drive with Windows XP SP3 installed on it. When the drive is connected through the standard SATA connector inside the laptop, everything works as expected. However when I remove the drive from the laptop and connect the drive to the external USB adapter, almost all files / folders lose the 'Owner' field contents. I was wondering why could that be. I've tried two USB adapters and this happens on each. I could take the ownership of all of the files, but this would overwrite the Owner value (the Owner value that is present when the drive is accessed through standard SATA connector in the laptop). //edit: if the hard drive is used through the USB adapter, I can't access most of the files, at least until I take ownership of the files (/folders). This is how it looks like: HDD inside USB adapter: HDD inside laptop: (note the Owner column) //edit: some of the files on the first screenshot have Owner field filled up. That's because I took the ownership of those files / folders to be able to access the files on the hard drive. //edit2: also, if the hard drive is connected through USB adapter and if I've took the ownership of some files by the 'ddd' user, then if i login as a different user (lets say 'eee' user), the owner field is _still_ empty: ddd user: eee user: eee user can't access the 'ddd' folder. Both users have Administrator priviledges.

    Read the article

  • FreeNAS pool configuration - RAID1 + other drives

    - by trnelson
    Simple questions, really. I found this answer with a similar setup, but not sure it answers my question. If it does, I'm curious why since the answer seems a bit unsure: ZFS Hard Drive Configuration in FreeNAS I'm building a server which will be used primarily for backup, plus some media streaming, possibly with Plex. I seem to understand most everything I need, but I'm still a bit confused on how pools work, and how to configure them for my scenario. I will have 2x 2TB WD Red drives, which I plan on using in a mirrored set up (RAID1). This would be for backup, and I'd also like to do offsite backup to my CrashPlan account from this array. I also have a few other drives: 1.5TB, 320GB, 250GB. I'm not sure exactly what to do with them yet, but looking for options. FreeNAS OS will be running from a 16GB USB Flash drive. Would it be wise to use the 1.5TB as a backup-backup, essentially as a mirror or perhaps for snapshots of the 2TB RAID1? I'm still learning about snapshots. Should the 2TB mirrored drives be in their own pool? Should the other drives be set up in their own pools as well, or should they be JBOD in a single pool? They may or may not get much use since the 2TB array is plenty for me. Does a dataset basically mimic the idea of a partition or a network share? In other words, I would map \SERVER\Share to X: on my laptop? Let's say I wanted to use the 250GB drive as an encrypted drive to store all of my cat pictures. Would it have to be in its own pool? If I use jails apps, should they go in the backup RAID1, or in another place? Thank you!

    Read the article

  • Wired to wireless bridge in Linux

    - by adrianmcmenamin
    I am attempting to set up my Raspberry Pi as a bridge (but I think this is not a question specific to the hardware) - using Debian wheezy. I have a hostapd.conf: (some details changed for security)... interface=wlan0 bridge=br0 driver=nl80211 auth_algs=1 macaddr_acl=0 ignore_broadcast_ssid=0 logger_syslog=-1 logger_syslog_level=0 hw_mode=g ssid=MY_SSID channel=11 wep_default_key=0 wep_key0=MY_KEY wpa=0 (yes, I know WEP is no good) And this in /etc/network/interfaces auto lo iface lo inet loopback iface eth0 inet dhcp allow-hotplug wlan0 iface wlan0 inet manual wpa-roam /etc/wpa_supplicant/wpa_supplicant.conf iface default inet dhcp auto br0 iface br0 inet dhcp bridge-ports eth0 wlan0 Everything seems to come up ok, but I cannot associate with the bridged wireless connection - even though the flashing lights on the USB stick suggest packets are being exchanged. I have read somewhere that not all cards/devices will run in hostap mode - they won't pass packets in one direction: is that right? (The info was a bit old)- this my card: [ 3.663245] usb 1-1.3.1: new high-speed USB device number 5 using dwc_otg [ 3.794187] usb 1-1.3.1: New USB device found, idVendor=0cf3, idProduct=9271 [ 3.804321] usb 1-1.3.1: New USB device strings: Mfr=16, Product=32, SerialNumber=48 [ 3.816994] usb 1-1.3.1: Product: USB2.0 WLAN [ 3.823790] usb 1-1.3.1: Manufacturer: ATHEROS [ 3.830645] usb 1-1.3.1: SerialNumber: 12345 So, what have I got wrong here?

    Read the article

  • organizing my music and my itunes

    - by Cawas
    What can we do to organize our music? I've got over 20k items on my iTunes Library, at least 5k with ratings and play counts, apparently just 12k music files and I can't understand how this question have not been properly answered yet. Maybe there is no answer. I have too many duplicates, broken links, bad music, corrupted files... Well, a big mess with no tags! Probably there's no single software capable of just organizing everything, though I'd love one. Hopefully some time in the near future we all will be able to just sync the cloud of our automagically selected music to the newly created offline copy. But meanwhile... Please, do consider I've at least gave a shot (even while not a full test drive) to every single answer linked here already, plus a few more. I'm fine with using other software (mac too, please) to organize, but I'd need it to sync (retrieve and put back) at least iTunes ratings, because of iPhone and smart playlists. Not looking for iTunes replacement. I'm hoping to hear what you hardcore music organizers out there are using as your own solutions! :) I myself am using way too many tools, getting way too little done and end up going song by song.

    Read the article

  • Is Ubuntu a viable replacement of Windows XP for small enterprise environments?

    - by Alex. S.
    Hi all, I'm a newbie systems administrator, so any advice would be great. I would like to setup ubuntu 8.04 lts in a small office of consulting in management (around 50 workstations) instead of Windows XP. I would install MS Office 2007 via WINE (*). It would be a fresh installation, so the migration would be less of a pain. The new setup would also include a small server as document repository and a backup server by now. Later, I would install another goodies like a IM server, a document management solution, and whatnot collaborative tool. What do you advice in this scenario? Do you think is viable? Should I try to convince my managers this is a good idea? I consider myself as a fair experienced user in both systems, and I'm the only guy in charge of everything. I need to cut costs down, and I think that antivirus and antimalware software are a waste of money and time. Is this good idea?, or should I resign and try to lock down the Windows systems and install AV software? Is there anything else in this setup I'm not foreseeing? (*) The only catch in my test machine until now had been that Office SmartArt doesn't work properly, the rest of Office 2007 may seem ok.

    Read the article

  • "could not find suitable fingerprints matched to available hardware" error

    - by Alex
    I have a thinkpad t61 with a UPEK fingerprint reader. I'm running ubuntu 9.10, with fprint installed. Everything works fine (I am able to swipe my fingerprint to authenticate any permission dialogues or "sudo" prompts successfully) except for actually logging onto my laptop when I boot up or end my session. I receive an error below the gnome login that says "Could not locate any suitable fingerprints matched to available hardware." What is causing this? here are the contents of /etc/pam.d/common-auth file # # /etc/pam.d/common-auth - authentication settings common to all services # # This file is included from other service-specific PAM config files, # and should contain a list of the authentication modules that define # the central authentication scheme for use on the system # (e.g., /etc/shadow, LDAP, Kerberos, etc.). The default is to use the # traditional Unix authentication mechanisms. # # As of pam 1.0.1-6, this file is managed by pam-auth-update by default. # To take advantage of this, it is recommended that you configure any # local modules either before or after the default block, and use # pam-auth-update to manage selection of other modules. See # pam-auth-update(8) for details. # here are the per-package modules (the "Primary" block) auth sufficient pam_fprint.so auth [success=1 default=ignore] pam_unix.so nullok_secure # here's the fallback if no module succeeds auth requisite pam_deny.so # prime the stack with a positive return value if there isn't one already; # this avoids us returning an error just because nothing sets a success code # since the modules above will each just jump around auth required pam_permit.so # and here are more per-package modules (the "Additional" block) auth optional pam_ecryptfs.so unwrap # end of pam-auth-update config #auth sufficient pam_fprint.so #auth required pam_unix.so nullok_secure

    Read the article

  • Unusable network, packet losses between router and NIC

    - by KáGé
    I have this setup: Gigabyte P35-DS3P motherboard Asus NX1101 PCI network card (the one on the motherboard got fried a few years ago by a power surge) Asus RT-N16 router Windows 7 x64 I think the other specs are irrelevant here, but I'll post them if you say so. Until a week ago everything was fine, but then my network became unusable: websites start loading but timeout before anything would come through (true for the web interface of the router as well), I can't reach the computer from my notebook and Windows' ping utility measures a ~50% packet loss between the computer and the router. Pinging localhost is good. The router works completely fine when wired to my notebook. I also tested different ports on the router, different cables, different router and connecting directly to the modem, but it's still the same. Sometimes it works for a few minutes right after turning on the machine, but then it becomes crap again, but mostly it's useless from the start. I've tried updating the firmware on the router, updating the driver for the network card (after which I started getting BSoDs in every 15 minutes), reinstalling Windows, swapping to Fedora 15 but none of them changed anything. Does this mean that the network card is dying, or could it be something else? If it's the card, what model do you recommend as a replacement? (Could be PCI or PCI-Ex x1) Thanks for your help.

    Read the article

  • MAMP Pro virtual hosts on Mountain Lion not being recognized

    - by user135242
    I'm running MAMP PRO 2.1.1 on OSX 10.8.1 and not having any luck getting Apache to recognize any hosts that have been set up in MAMP besides localhost. This only happens when trying to use port 80. When I switch to port 8888 everything runs fine. Mountain Lion's Apache has been disabled and I get no errors or warnings when starting MAMP and the servers. Any doc root I set for "localhost" runs without problem. Any other server name I define, however, results in "cannot connect" when viewing in Chrome (not to be confused with "cannot find" - the browser is in fact following /etc/hosts to 127.0.0.1, but MAMP's Apache is simply not responding) I was wondering if anyone else has run into this issue or knows how to solve it. I'm working on some WordPress development and it keeps wanting to redirect to the base URL (with no port reference) even during setup. I'm sure I could fix things from the WP side but I'd rather figure out what the root issue is with MAMP. Thanks in advance for any insight you can provide.

    Read the article

< Previous Page | 535 536 537 538 539 540 541 542 543 544 545 546  | Next Page >