Search Results

Search found 15595 results on 624 pages for 'ip forward'.

Page 544/624 | < Previous Page | 540 541 542 543 544 545 546 547 548 549 550 551  | Next Page >

• Connecting to my home router web interface from work

  - by Joe

  Hi, I'm trying to connect to my home router web interface from work. I use dyndns, because I don't have a static IP at home, and it works perfectly from any other place except my workplace (update: I made a mistake, see edit below). When trying to access the web interface from work I get a "500 Server Error" with the code: SERVER_RESPONSE_RESET. I'm not trying to use any protocols such as remote desktop, I'm only trying to access the web interface. I can access any other web page from my workplace with no problems, and I think my router web interface is like any other web page, isn't it? I thought maybe my work place proxy blocks addresses of services like dyndns, so I also applied another trick. Since I have a web page on my own domain (say www.mydomain.com) which I can access from work, I tried adding a CNAME to my domain which is linked to the dyndns address (router.mydomain.com). This way if anyone enters the address router.mydomain.com from anywhere, they reach my home router web interface, and there's no way of knowing it's a dyndns address (or is there?). However, it still doesn't work from my workplace (I get the same error message). Any ides? Edit: I'm sorry to say I made a mistake earlier. I used to be able to access my home router web interface from my old workplace, and I thought it was still possible since I don't recall making any configuration changes. However, after reading the replies, I went over to my old workplace and checked, and it doesn't work from there either. I'm very sorry for giving out wrong and misleading information about my problem. So to summarize: my problem is that I can't access my home router web interface from anywhere.

  Read the article

• Prevent nginx from redirecting traffic from https to http when used as a reverse proxy

  - by Chris Pratt

  Here's my abbreviated nginx vhost conf: upstream gunicorn { server 127.0.0.1:8080 fail_timeout=0; } server { listen 80; listen 443 ssl; server_name domain.com ~^.+\.domain\.com$; location / { try_files $uri @proxy; } location @proxy { proxy_pass_header Server; proxy_redirect off; proxy_set_header Host $http_host; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_set_header X-Forwarded-Proto https; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Scheme $scheme; proxy_connect_timeout 10; proxy_read_timeout 120; proxy_pass http://gunicorn; } } The same server needs to serve both HTTP and HTTPS, however, when the upstream issues a redirect (for instance, after a form is processed), all HTTPS requests are redirected to HTTP. The only thing I have found that will correct this issue is changing proxy_redirect to the following: proxy_redirect http:// https://; That works wonderfully for requests coming from HTTPS, but if a redirect is issued over HTTP it also redirects that to HTTPS, which is a problem. Out of desperation, I tried: if ($scheme = 'https') { proxy_redirect http:// https://; } But nginx complains that proxy_redirect isn't allowed here. The only other option I can think of is to define the two servers separately and set proxy_redirect only on the SSL one, but then I would have duplicate the rest of the conf (there's a lot in the server directive that I omitted for simplicity sake). I know I could also use an include directive to factor out the redundancy, but I really want to keep just one conf file without any dependencies. So, first, is there something I'm missing that will negate the problem entirely? Or, second, if not, is there any other way (besides including an external file) to factor out the redundant config information so that I can separate out the HTTP and HTTPS versions of the server config?

  Read the article

• Router startup problems

  - by gfmoz

  I have problems with my Tilgin Vood Router. As I try to start my router by turning the power on (captain obvious), it generally doesn't work the first 3-4 times. This is getting very annoying. Five minutes after turning the power on the router's signal LEDs don't blink in the way they should do in a connected state. I can connect to my routers web configuration interface through my PC connected to it via LAN though I can't access the internet. It usually takes the router five minutes to get to the point where it should be connected to the internet but as it doesn't work the first times. So I turn on my router 3-5 times, let him work 5 minutes and then suddenly, after turning the power off and on again it all works. I also have to restart my PC too in order for everything to work. How can I solve this problem? Just leave the router turned on all time? I prefer a daily IP switch, though. May the problem have something to do with my PC? There is another one connected to the router too and it doesn't work there either.

  Read the article

• Router startup problems

  - by gfmoz

  I have problems with my Tilgin Vood Router. As I try to start my router by turning the power on (captain obvious), it generally doesn't work the first 3-4 times. This is getting very annoying. Five minutes after turning the power on the router's signal LEDs don't blink in the way they should do in a connected state. I can connect to my routers web configuration interface through my PC connected to it via LAN though I can't access the internet. It usually takes the router five minutes to get to the point where it should be connected to the internet but as it doesn't work the first times. So I turn on my router 3-5 times, let him work 5 minutes and then suddenly, after turning the power off and on again it all works. I also have to restart my PC too in order for everything to work. How can I solve this problem? Just leave the router turned on all time? I prefer a daily IP switch, though. May the problem have something to do with my PC? There is another one connected to the router too and it doesn't work there either.

  Read the article

• Prevent SSL certificate being returned for a specific domain

  - by jezmck

  Apologies for a long question: We've taken on a new client whose web hosting was previously on their in-house server which still has their Exchange/Outlook email. We now host their domain (and many others) on our server. They're complaining that they're getting errors in Outlook. I don't understand the AutoDiscover stuff at the root of the problem, but believe that I just need to stop the SSL certificate on our server being returned when requested at a particular domain: Yes it is, the issue lies with "{newclient}.com" being pointed to your server IP and that server has Port 443 open with an SSL certificate associated to it. So when Outlook/ActiveSync use autodiscover to find the mailbox settings it find your SSL (because 443 is open) and flags it as an error. The solution is to close 443 so its not discovered, Autodiscover will then proceed to mail.{newclient}.com via the MX / ServiceRecords and discover the correct SSL. I'm new here and there was no hand-over, so I don't know whether other currently hosted sites need to accept SSL connections, though I suspect some will, or may in future. This is a live server, so I can't risk trying loads of options in case I take the server offline! I feel like I should be adding something like the following to vhosts.conf. <VirtualHost *:443> ServerName {newclient}.com ServerAlias www.{newclient}.com SSLEngine Off SSLCertificateFile {NONE} SSLCertificateKeyFile {NONE} </VirtualHost> Apologies for the fact that I don't know enough about this subject to be able to ask the question more clearly!

  Read the article

• OpenVPN Keeps Crashing

  - by Frank Thornton

  Oct 20 21:00:44 sb1 openvpn[2082]: <MY_IP>:28523 [vpntest] Peer Connection Initiated with [AF_INET]<MY_IP>:28523 Oct 20 21:00:44 sb1 openvpn[2082]: vpntest/<MY_IP>:28523 MULTI_sva: pool returned IPv4=10.8.0.6, IPv6=(Not enabled) Oct 20 21:00:44 sb1 openvpn[2082]: <MY_IP>:28522 WARNING: 'link-mtu' is used inconsistently, local='link-mtu 1576', remote='link-mtu 1376' Oct 20 21:00:44 sb1 openvpn[2082]: <MY_IP>:28522 WARNING: 'tun-mtu' is used inconsistently, local='tun-mtu 1532', remote='tun-mtu 1332' Oct 20 21:00:45 sb1 openvpn[2082]: <MY_IP>:28522 [vpntest2] Peer Connection Initiated with [AF_INET]<MY_IP>:28522 Oct 20 21:00:45 sb1 openvpn[2082]: vpntest2/<MY_IP>:28522 MULTI_sva: pool returned IPv4=10.8.0.10, IPv6=(Not enabled) Oct 20 21:00:46 sb1 openvpn[2082]: vpntest/<MY_IP>:28523 send_push_reply(): safe_cap=940 Client File: client dev tun proto tcp remote <IP> 443 resolv-retry infinite nobind tun-mtu 1500 tun-mtu-extra 32 mssfix 1410 persist-key persist-tun auth-user-pass comp-lzo SERVER: port 443 #- port proto tcp #- protocol dev tun tun-mtu 1500 tun-mtu-extra 32 reneg-sec 0 #mtu-disc yes mssfix 1410 ca /etc/openvpn/easy-rsa/2.0/keys/ca.crt cert /etc/openvpn/easy-rsa/2.0/keys/server.crt key /etc/openvpn/easy-rsa/2.0/keys/server.key dh /etc/openvpn/easy-rsa/2.0/keys/dh1024.pem plugin /etc/openvpn/openvpn-auth-pam.so /etc/pam.d/login #plugin /usr/share/openvpn/plugin/lib/openvpn-auth-pam.so /etc/pam.d/login #- Comment this line if you are using FreeRADIUS #plugin /etc/openvpn/radiusplugin.so /etc/openvpn/radiusplugin.cnf #- Uncomment this line if you are using FreeRADIUS client-to-client client-cert-not-required username-as-common-name server 10.8.0.0 255.255.255.0 push "redirect-gateway def1" push "dhcp-option DNS 8.8.8.8" push "dhcp-option DNS 8.8.4.4" keepalive 3 30 comp-lzo persist-key persist-tun What is causing the VPN to keep dropping the connection and then reconnecting?

  Read the article

• Why *do* windows print queues occasionally choke on a print job

  - by Ian

  Y'know they way windows print queues will occasionally stop working with a print job at the head of the queue which just won't print and which you can't delete? Anyone know whats going on when this happens? I've been seeing this since the NT4 days and it still happens on 2008. I'm talking about standard IP connected laser printers - nothing fancy. I support a lot of servers and loads of workstations and see this happen a few times a year. The user will call saying they can't print. When you examine the print queue, which in my case will generally be a server based queue shared out to the workstations, you find a print job which you cannot cancel. You also can't pause it, reinitialize it, nothing. Stopping the spooler is the usual trick and works sometimes. However I occasionally see cases which even this doesn't cure and which a reboot is the only solution. Pause the queue, reboot, when it comes back up the job can then be deleted. Once gone the printer happily goes back to its normal state. No action is ever necessary on the printer. I regard having to reboot as last resort and don't like it. What on earth can be going on when stopping the process (spooler) and restarting it doesn't clear a problem? Its not linked to any manufacturer either. I've seen this on HPs, lexmark, canon, ricoh, on lasers, on plotters.... can't say I ever saw this on dot matrix. Anyone got any ideas as to what may be going on. Ian

  Read the article

• Nginx and Gunicorn hanging on GET requests

  - by whatWhat

  I'm using Nginx + Gunicorn which is serving my Django project. All GET requests hang for ~1 min. The content seems to be available immediately as I can see it in the Browser inspector but the browser itself looks like it's still waiting for more data. Heres my Ngnix config #allow for up to 3 connections per second. limit_req_zone $binary_remote_addr zone=one:10m rate=3r/s; server { listen 80; server_name example.com; root /var/www/example.com/example/; # serve directly - analogous for static/staticfiles location /media/ { # this changes depending on your python version root /home/example/; } location /static/ { # if asset versioning is used if ($query_string) { expires max; } root /var/www/example.com; } location / { #Allow for a burst of 50. limit_req zone=one burst=50 nodelay; proxy_pass_header Server; proxy_set_header Host $http_host; proxy_redirect off; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Scheme $scheme; proxy_connect_timeout 10; proxy_read_timeout 10; proxy_pass http://localhost:8001/; } # what to serve if upstream is not available or crashes error_page 500 502 503 504 /media/50x.html; } My Gunicorn Config: bind = "127.0.0.1:8001" workers = 3 worker_class = "gevent" Is there anything obvious that would be causing the requests to stay open for so long?

  Read the article

• Clarification for setting up SSH terminal access on Cisco IOS

  - by Matt Malesky

  I'm attempting to set up SSH on a Cisco 2811 and having some difficulties. The first step to this should be running crypto key generate rsa I seem to be missing this though: better#crypto key generate rsa ^ % Invalid input detected at '^' marker. better# Furthermore, the only available commands I have in the crypto key namespace are lock and unlock, which seem to indicate a locked keypair (for which I don't know the password): better#crypto key ? lock Lock a keypair. unlock Unlock a keypair. better#crypto key unlock ? rsa RSA keys better#crypto key unlock rsa %% Please enter the passphrase: %% Unlocking failed. . better# More or less, I'm asking what exactly this might mean, and if I actually do have certificates already here (used router)? Otherwise, how can I solve this? It's my first time configuring this feature, but I definitely believe it's part of my IOS. Speaking of my IOS, I'm running the image c2800nm-advsecurityk9-mz.124-24.T6.bin I'll also note that I have my hostname and ip domain-name configured. I'll also give you a dir flash: below if it's at all of use: better#dir flash: Directory of flash:/ 2 -rw- 2748 Jul 27 2009 14:03:52 +00:00 sdmconfig-2811.cfg 3 -rw- 931840 Jul 27 2009 14:04:10 +00:00 es.tar 4 -rw- 1505280 Jul 27 2009 14:04:32 +00:00 common.tar 5 -rw- 1038 Jul 27 2009 14:04:46 +00:00 home.shtml 6 -rw- 112640 Jul 27 2009 14:05:00 +00:00 home.tar 7 -rw- 1697952 Jul 27 2009 14:05:26 +00:00 securedesktop-ios-3.1.1.45-k9.pkg 8 -rw- 415956 Jul 27 2009 14:05:46 +00:00 sslclient-win-1.1.4.176.pkg 9 -rw- 38732900 Dec 8 2011 06:28:56 +00:00 c2800nm-advsecurityk9-mz.124-24.T6.bin 64016384 bytes total (20598784 bytes free) better#

  Read the article

• will heavy network traffic affect other connections on HP ProCurve V1810-48G?

  - by nn4l

  I have a HP ProCurve V1810-48G switch with a few servers connected to it (everything in one rack). The switch is practically in its default configuration. During copying of a few hundred GByte of data from server_a to server_b (using tar cf - data | ssh server_b 'cd myhome; tar xf -'), essentially saturating the network capacity between those two servers, I noticed network related error messages on the console of server_c - as if server_c is no longer able to send/receive traffic to server_d. After canceling the copy command everything was normal again. I would understand this if the network connection would use a shared resource, for example if server_a and server_c are in one datacenter, server_b and server_d are in another datacenter and both datacenters are connected with a 100 MBit line. But all of the mentioned servers are connected to the same switch and are located in the same IP network. I always thought that a connection between two servers on one switch will not affect any other server connected to the switch. It is also possible that the network related error messages are caused by something else - but I can't risk a network problem for any other system on this switch. Please advise.

  Read the article

• Translating debian network configuration to gentoo

  - by thpetrus

  I just got rid off Debian on my VPS (OpenVZ) and installed Gentoo on it, however it is a plain Gentoo image without further configuration, i.e. no working network. I'm not familiar with Debian and coulnd't figure out how to get the network set up, these are the debian network files /etc/network/interfaces: auto venet0 iface venet0 inet manual up ifconfig venet0 up up ifconfig venet0 127.0.0.2 up route add default dev venet0 down route del default dev venet0 down ifconfig venet0 down iface venet0 inet6 manual up ifconfig venet0 add ipv6addr/128 down ifconfig venet0 del ipv6addr/128 up route -A inet6 add default dev venet0 down route -A inet6 del default dev venet0 auto venet0:0 iface venet0:0 inet static address external_ip netmask 255.255.255.255 auto venet0:1 iface venet0:1 inet static address internal_ip netmask 255.255.255.255 Please note that external_ip, internal_ip and ipv6addr are placeholders. I copied the /etc/resolv.conf, know the gateway_ip and also have another ouput of ifconfig, if necessary. This is what I came up with, /etc/conf.d/net: config_venet0="127.0.0.2 netmask 255.255.255.255 brd 0.0.0.0" config_venet0:0="external_ip netmask 255.255.255.255 brd 0.0.0.0" route_venet0:0="default via gateway_ip" config_venet0:1="internal_ip netmask 255.255.255.255 brd 0.0.0.0" Broadcast IP is taken from ifconfig debian output - however it doesn't work. A symbolic link net.venet0:0 -> net.lo in /etc/init.d/ was created and I added net.venet0:0 to the boot runlevel.

  Read the article

• Windows 7 can't see wireless printer

  - by Chance Robertson

  I have a P1102W printer from HP. I have a Windows 7 machine. I have a MacBook Pro. I setup the printer following the instructions from the Windows 7 machine. I am able to print from the Mac but not the Windows 7 machine. And to add, I am not able to print from any Windows 7 machines. The MacBook Pro address is 198.168.2.115, the Windows machine is 192.168.2.117, and the printer in 192.168.2.140. I can ping the printer from the Mac. I can ping the Windows 7 machine from the mac. I can ping the mac from the windows 7 machine. When I try to ping the printer from the Windows 7 machine I get destination unreachable. I can browse to the printer IP address from the mac and not the Windows 7. I have turned off the firewall on the Windows 7 machine and turned on network sharing. Is there something else I am missing. I can connect the printer with a USB cable to the Windows machine and print. I can not get the Windows machine to see the printer even though they are on the same network.

  Read the article

• trying to figure out how to bridge two virtual networks together and in turn bridge that to the internet for a virtual inline IDS/IPS system

  - by Tony robinson

  I'm trying to figure out how to bridge two vmware (server or workstation, workstation) or virtualbox networks together with a linux IDS/IPS system transparently inline between both the virtual networks. How do I accomplish this? I understand how to bridge to virtual networks together, but how to I make the linux virtual machine sit between them and force traffic to go across the transparent bridge? I would like to have something along the lines of: vmnet a various vms host-only network ---- inline linux box vmnet a boxes forced to go through here to get to the internet --- vmnet b network with internet access configured as either NAT or bridged -- internet I know that basically the linux box needs two virtual nics, one on vmnet a and vmnet b, but other than that, I don't know how to force all the traffic to go across the "transparent" bridging linux box on its way to the internet. Do vmnet a and b have to be the same ip network with the same default route? does vmnet a not have a default route and vmnet b have a default route? I've read in vmware forums that on the linux host you need to change permissions on the vmnet files for promiscuous mode? is this true? how do you configure this scenario on a windows box?

  Read the article

• ssh_exchange_identification: Connection closed by remote host

  - by rick

  Firstly, I know that this question has been asked a million times, and I have read everything I can find and still cannot fix the problem. i am encountering this issue when ssh'ing in from my mac to my Ubuntu server on a fresh install of Ubuntu (I reinstalled because of this issue). I have SSH portmapped to 7070 because my ISP is blocking 22. On the client: bash: ssh -p 7070 -v [email protected] debug1: Reading configuration data /etc/ssh_config debug1: Connecting to address.org port 7070. debug1: Connection established. debug1: identity file /home/me/.ssh/identity type -1 debug1: identity file /home/me/.ssh/id_rsa type 1 debug1: identity file /home/me/.ssh/id_dsa type -1 ssh_exchange_identification: Connection closed by remote host Here's what I have done to try to resolve the issue: Made sure my maxstartups is ok: bash: grep MaxStartups /etc/ssh/sshd_config #MaxStartups 10:30:60 Made sure hosts.deny is clear of denials. Made sure hosts.allow has my client IP. Clear out known_hosts on client Changed ownership of /var/run to root Made sure etc/run/ssh is Made sure /var/empty exists Reinstall openssh-server Reinstall ubuntu When I run telnet localhost, I get this: telnet localhost Trying ::1... Trying 127.0.0.1... telnet: Unable to connect to remote host: Connection refused When I run /usr/sbin/sshd -t Could not load host key: /etc/ssh/ssh_host_rsa_key Could not load host key: /etc/ssh/ssh_host_dsa_key When I regenerate the keys with ssh-keygen -t rsa -f /etc/ssh/ssh_host_rsa_key ssh-keygen -t dsa -f /etc/ssh/ssh_host_dsa_key I get the same error. I am pretty sure this is the issue. Can anyone help?

  Read the article

• How to deploy website in IIS with a host name?

  - by Jayakumar

  I try to host my application in IIS. Below are the steps that I follow: Publish the code and place it in a path. Open IIS, right click on "sites" and select "Add Website". In that dialog I gave the site name and selected the app pool created for the application. I selected the physical path of the published code. I left the IP and port in the binding section without changes. and, finally, gave the host name as fus.km.com. When I try to browse the application the page is not Loading "Internet Explorer cannot display the Page" The machine domain is km.com UPDATE I tried to add the host name to the host file and flushed the DNS. The application asked for user credentials (I use windows Authentication in the application). But it did not login. On repeated tries it throws the error: HTTP Error 401.1 - Unauthorized You do not have permission to view this directory or page using the credentials that you supplied. I tried with different user to login but I get the same result.

  Read the article

• How to Load Balance 2 Internet Connections on a Windows 7 machine?

  - by Jimmy Chandra

  It's sort of related to this particular question, but that one is on Mac. I am looking for similar solution on Windows 7. I have 2 network connections: (Connection A) Wireless terminal connecting to ISP A (3G / EVDO internet provider) (Connection B) Broadband wired connection connecting to ISP B (Cable internet provider) Both has access to the internet. When I try connecting to a website and checking the networking tab on my Task Manager, I only see the network traffic being routed to only Connection A. Is there a way to make the computer to utilize both network (in a sense using all the bandwidth available from both the Cable ISP and the 3G / EVDO ISP) at the same time? If so, what do I need to do to set this up ... on Windows 7? Here is a bit more info on my network connections (ipconfig /all): PPP adapter Wireless Terminal: IPv4: aa.bb.ccc.ddd(preferred) Subnet mask: 255.255.255.255 Default Gateway: 0.0.0.0 DNS: aa.ee.f.ggg aa.ee.f.hhh Primary Wins: jjj.ii.k.l Secondary Wins: jjj.ii.k.m Ethernet adapter LAN: IPv4: 192.168.1.100 (connected to a router by wired that itself connect to a cable modem) subnet mask: 255.255.255.0 Default gateway: 192.168.1.1 (the wireless router) DHCP: 192.168.1.1 (the wireless router) DNS: xxx.yy.zz.ww rr.sss.t.uuu For my own privacy, I don't believe the actual number matters, the patterns are representative of the ip numbering scheme...

  Read the article

• Barriers to IPv6 deployment: addressing

  - by sysadmin1138

  There are several things that are keeping IPv6 deployment from being a topic of active discussion here at my work. There are the usual technical issues, but one non-technical one appears to be a major stumbling block on the path to actually getting a deployment project going. Addresses, memorizing of. Specifically, IPv4 addresses are comprehensible, and IPv6 addresses just look like a big long string of hex. The human mind has real trouble memorizing lists of more than 7-8 items, and an IPv4 address (192.168.231.148) has four items in it which makes it easy for us to memorize. A fully populated IPv6 address has not only 8 sections, but each section has 4 hex digits in it. IPv6 addresses were not designed for memorization. To the technician who knows that the DNS server is at 192.168.42.42 (or more likely "42.42", since the company prefix is likely memorized), the idea of memorizing an IPv6 address fills them with dread. Which in turn makes them much less enthusiastic about participating in an IPv6 deployment project. Because of how our network works we're not fully dynamic in terms of v4 addressing. We have several to many subnets that are entirely statically assigned for a variety of reasons, chief among them being that the overhead of static DHCP assignments is perceived as being too great. Also, some devices still aren't smart enough to pull DNS addresses out of DHCP while also having a static assignment, and therefore require manually configured DNS settings. Therefore, some v6 address memorization will have to be done. We're not under any mandate to get v6 out the door, so we don't have pressure from the top. However, it is time to start prepping our infrastructure to handle IPv6 even if we don't convert wholesale. For those of you who have been in IPv6-land for a while, what short-cut methods do you use to discuss or keep track of subnets and specific/critical IP addresses? If I can help reduce some of the dread surrounding IPv6 we might get the project going.

  Read the article

• CentOS 6.3 Virtual under OpenVZ cannot ping, host lookups, outbound connections while postfix running

  - by Paul Cravey

  My best theory is that some kernel limit is being hit preventing outbound connections. We have tried basically everything from tcpdumps to provisioning an entirely new virtual server (we do not have this problem on any other virtuals), however the problem somehow carried over, even with new postfix build (working). Emails work, and outbound connections work, so long as postfix does not have too much going on. /proc/user_beancounters shows no limits being hit (show below). Nevertheless, pings fail even to IP addresses. TCP stack appears healthy. Load is low. No iowait. Flushed iptables already. Has anyone experienced anything like this? uid resource held maxheld barrier limit failcnt 3: kmemsize 166216365 170262528 9223372036854775807 9223372036854775807 0 lockedpages 0 0 9223372036854775807 9223372036854775807 0 privvmpages 285727 351885 9223372036854775807 9223372036854775807 0 shmpages 16933 17605 9223372036854775807 9223372036854775807 0 dummy 0 0 0 0 0 numproc 150 303 9223372036854775807 9223372036854775807 0 physpages 314156 326191 0 1280000 0 vmguarpages 0 0 9223372036854775807 9223372036854775807 0 oomguarpages 165355 165355 9223372036854775807 9223372036854775807 0 numtcpsock 89 172 9223372036854775807 9223372036854775807 0 numflock 22 76 9223372036854775807 9223372036854775807 0 numpty 1 2 9223372036854775807 9223372036854775807 0 numsiginfo 0 75 9223372036854775807 9223372036854775807 0 tcpsndbuf 2733472 4371752 9223372036854775807 9223372036854775807 0 tcprcvbuf 1798336 5427296 9223372036854775807 9223372036854775807 0 othersockbuf 491120 1000760 9223372036854775807 9223372036854775807 0 dgramrcvbuf 0 238728 9223372036854775807 9223372036854775807 0 numothersock 361 505 9223372036854775807 9223372036854775807 0 dcachesize 135941831 136114679 9223372036854775807 9223372036854775807 0 numfile 2905 4990 9223372036854775807 9223372036854775807 0 dummy 0 0 0 0 0 dummy 0 0 0 0 0 dummy 0 0 0 0 0 numiptent 8 9 9223372036854775807 9223372036854775807 0 [root@bni /]# ping 4.2.2.1 PING 4.2.2.1 (4.2.2.1) 56(84) bytes of data. --- 4.2.2.1 ping statistics --- 9 packets transmitted, 0 received, 100% packet loss, time 8493ms [root@bni /]# service postfix stop [root@bni /]# ping 4.2.2.1 PING 4.2.2.1 (4.2.2.1) 56(84) bytes of data. 64 bytes from 4.2.2.1: icmp_seq=1 ttl=53 time=8.63 ms 64 bytes from 4.2.2.1: icmp_seq=2 ttl=53 time=8.62 ms 64 bytes from 4.2.2.1: icmp_seq=3 ttl=53 time=8.63 ms 64 bytes from 4.2.2.1: icmp_seq=4 ttl=53 time=8.66 ms Outbound connections of all sorts fail when postfix is running.

  Read the article

• Filesharing mac 10.6 with windows vista

  - by adam

  Ive followed all the tutorials on the net to no avail. I can see my vista pc in finder on the mac but when I click on it tries to connect but fails. The same is true from vista, it can see the mac but i cant connect. Wont even offer a login box. So I tried to troubleshoot by using a 3rd computer with xp. It joined the network and can access both the mac and vista on the same workgroup. Mac sees it and it shows under finder but i cant access it by clicking on the icon i have to access by using the ip of the xp machine...strange. Ive turned off all my firewalls. The fact that xp can connnet to the others and vice versa boggles my mind why vista and mac cant connect directly. Oh and pings indicates the same. I.e. xp has no problem but mac to vista and vice versa fails. Can anyone help.

  Read the article

• Troubleshoot IIS 6 and Intermittent SQL Server Connectivity Loss

  - by jpsnow

  I am not a System Administrator, but I am temporarily trying to fill that role. I have 2 Windows 2003 Servers. 1 server has my Microsoft SQL Database (SQL Server 2005) and the other is the web server with IIS6. Intermittently (once every month or 2) the web server loses connectivity to the database server for a period of roughly 10 minutes. It normally regains connectivity without intervention. The website is set up to send me an email when there is a problem connecting to the database. Within the email, I get the error code: [Microsoft][ODBC SQL Server Driver][TCP/IP Sockets]SQL Server does not exist or access denied. I am able to access both servers during the outage. I can go to my SQL server and open up SQL server without any issues. I have looked in the EventViewer and do not see anything. The last time that I had this issue, I stopped IIS6 and started it. After doing this, the issue was resolved. This leads me to believe that it is an issue with IIS and not SQL server. How can I begin troubleshooting?

  Read the article

• Road Warrior VPN Setup

  - by wobblycogs

  I apologise up front for the rather open ended nature of this question but I've got well out of my depth and could really do with some pointers. I need to set up a road warrior VPN solution which will allow our customers to securely access a number of services we provide for them. Customer machines will be running a variety of Windows versions from XP onwards with a variety of patch levels. Typically they will connect from the clients main offices but not always. It is safe to assume that all clients will be behind NATs but we may occasionally see a connection that isn't NAT'ed. Typical connection situation is therefore: Customer Laptop -- Router (NAT) -- Internet -- VPN Server + Firewall -- Server (Win 2008 R2, Non-routable IP) There will initially be a dozen or so people that could connect but that will grow quickly to around 100. It's unlikely that we'll see that many concurrent connections though, I imagine our total VPN throughput would be <50Mbps peak. What are my options for setting this up? I've been trying to set up a system like this using a MikroTik router for a few days but have struggled to get it working correctly, particularly with NAT'ed clients. I've had a quick look at OpenVPN and liked what I saw but I think it's unlikely our customers IT departments would allow the client to be installed. Finally I've looked at the Cisco ASA range but I'm on a fairly tight budget so this is less preferable but it looks like it would work pretty much out of the box. My fall back position is to connect the server directly and use the provided VPN + Firewall facilities but that is far from ideal as the number of servers is likely to grow over time.

  Read the article

• Shorewall log question.

  - by Shikoru

  I have been getting various attempts to connect to ports on my shorewall firewall. The ports that I keep seeing connection attempts at are tcp 44444, tcp 44446, udp 55555 and every now and then some slight variation. I ran "netstat -a" and did not see anything listening on those ports. Is this something that I should be worried about or is it just some rouge computers out there? I have noticed alot of the ip addresses are from Spain and Mexico. May 25 18:39:35 Takkun kernel: [62516.626514] Shorewall:net2fw:DROP:IN=eth0 OUT= MAC=00:d0:b7:65:d4:13:34:ef:xx:xx:xx:81:08:00 SRC=200.124.9.113 DST=72.xxx.xxx.xxx LEN=48 TOS=0x00 PREC=0x00 TTL=112 ID=51796 DF PROTO=TCP SPT=2071 DPT=44446 WINDOW=16384 RES=0x00 SYN URGP=0 May 25 18:39:52 Takkun kernel: [62535.433285] Shorewall:net2fw:DROP:IN=eth0 OUT= MAC=00:d0:b7:65:d4:13:34:ef:xx:xx:xx:81:08:00 SRC=72.50.95.174 DST=72.xxx.xxx.xxx LEN=90 TOS=0x00 PREC=0x00 TTL=105 ID=31130 PROTO=UDP SPT=59505 DPT=55555 LEN=70 May 25 18:40:05 Takkun kernel: [62548.963413] Shorewall:net2fw:DROP:IN=eth0 OUT= MAC=00:d0:b7:65:d4:13:34:ef:xx:xx:xx:81:08:00 SRC=77.12.37.1 DST=72.xxx.xxx.xxx LEN=90 TOS=0x00 PREC=0x00 TTL=108 ID=9585 PROTO=UDP SPT=20401 DPT=55555 LEN=70 That is the jist of what im seeing.

  Read the article

• System Slow After Uprading Ubuntu

  - by Aragon N

  I have an Ubuntu network machine which has release of 10.04.1 LTS Lucid. On this system I have Apache, PostgreSQL and django. For some app. development I have to install PGP and php-curl. Due to being on network, I have exported a VMware machine to the Internet and firstly I have upgraded the system and then installed php5 packages on it. I don't know is it all about django or apache configuration. Maybe some Apache settings had changed. In this case in apache where I have to look at ? After all replacing it with its old place, I see that the new system query is slow according to another. Old system query time : 140 ms New system query time : 9.11 s I have checked /etc/network interface and it seems there is no problem. I have checked /etc/resolv.conf and it seems OK I have checked /etc/nsswitch.conf and only host section is different from old one which old system has hosts: files mdns4_minimal [NOTFOUND=return] dns mdns4 and then I have checked time host -t A services.myapp.com and I got real 0m0.355s user 0m0.010s sys 0m0.020s and I have checked apache2 HostnameLookups : find /etc/apache2/ -type f | xargs grep -i HostnameLookups It returned : /etc/apache2/apache2.conf:# HostnameLookups: Log the names of clients or just their IP addresses /etc/apache2/apache2.conf:HostnameLookups Off and now what can I have to check for boosting my system as before?

  Read the article

• What was SPX from the IPX/SPX stack ever used for?

  - by Kumba

  Been trying to learn about older networking protocols a bit, and figured that I would start with IPX/SPX. So I built two MS-DOS virtual machines in VirtualBox, and got IPX communications working (after much trial and error). The idea being to get several old DOS games to run, link up to a multiplayer match, interact with each game window, and capture the traffic using Wireshark from the host machine. From this, I got Quake, Masters of Orion 2, and MechWarrior 2 to communicate back and forth. Doom, Doom2, Duke3d, Warcraft, and several others either buggered up under the VM or just couldn't see the other VM on the IPX network. What did I discover? None of the working games used SPX. Not even Microsoft's NET DIAG used SPX. They all ran ONLY on top of IPX. I can't even find SPX examples or use-cases of SPX traffic running over IEEE 802.3 Ethernet II framing. I did find references that it was in abundant use on token ring, but that's it. Yet any IPX-aware application that I've hunted down so far usually advertises itself as "IPX/SPX", which seems to be a bit of a misnomer, since it doesn't seem to use SPX. So what was SPX used for? Any DOS applications out there that use it which will run under my VM setup? Edit: I am aware that IPX is to SPX as IP is to TCP (layer 3 to layer 4), so I expected to see an SPX layer underneath the IPX layer in Wireshark when I ran my tests.

  Read the article

• After few days of server running fine with nginx it start throwing 499 and 502

  - by Abhay Kumar

  Nginx start throwing 499 and 502 after running fine for few days, website is a rails app using thin as the webserver. Restarting the Nginx doent not seem to help. Below the the Nginx config Nginx config under sites-enabled upstream domain1 { least_conn; server 127.0.0.1:3009; server 127.0.0.1:3010; server 127.0.0.1:3011; } server { listen 80; # default_server; server_name xyz.com *.xyz.com; client_max_body_size 5M; access_log /home/ubuntu/www/xyz/current/log/access.log; root /home/ubuntu/www/xyz/current/public/; index index.html; location / { proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_set_header Host $http_host; proxy_redirect off; proxy_read_timeout 150; if (!-f $request_filename) { proxy_pass http://domain1; break; } } }

  Read the article

< Previous Page | 540 541 542 543 544 545 546 547 548 549 550 551  | Next Page >