Search Results

Search found 58094 results on 2324 pages for 'http status codes'.

Page 545/2324 | < Previous Page | 541 542 543 544 545 546 547 548 549 550 551 552  | Next Page >

• NIC are not advertising Correct Speeds

  - by Squidly

  I have an IBM x336 that is not advertising the proper LINK speeds. One interface is the other is not. I've tried to Force it to 1000/Full but then it just shows link down. I have confirmed the switch is set to auto negotiate like my switches. I have also changed out my Ethernet Cables. I'm at a loss where to look further. I have verified that it will connect at 1G on a different swtich. This also has happened on two different servers on the same switch. This is my output from mii-tool -v for each interface. eth0: negotiated 100baseTx-FD, link ok product info: vendor 00:08:18, model 24 rev 0 basic mode: autonegotiation enabled basic status: autonegotiation complete, link ok capabilities: 1000baseT-HD 1000baseT-FD 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD advertising: 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD flow-control link partner: 1000baseT-HD 1000baseT-FD 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD eth1: negotiated 1000baseT-FD flow-control, link ok product info: vendor 00:08:18, model 24 rev 0 basic mode: autonegotiation enabled basic status: autonegotiation complete, link ok capabilities: 1000baseT-HD 1000baseT-FD 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD advertising: 1000baseT-FD 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD flow-control link partner: 1000baseT-HD 1000baseT-FD 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD

  Read the article

• Is .htaccess slowing down my dedicated server?

  - by David Robles

  First of all, I consider myself more a programmer than a servers guy. I have a website where I receive about 3,000 visits per day, which I think is a lot less than the max capacity for a dedicated server. However, I've noticed that the connection to the website is pretty slow, e.g., to load images, to connect to it via SSH, etc. I configured .httaccess recently to avoid hotlinking to images in my server (i.e. .jpg, .gif and .png), and I was wondering if that could be slowing down my website. This is the configuration that I have: # BEGIN WordPress <IfModule mod_rewrite.c> RewriteEngine On RewriteBase / RewriteEngine on RewriteCond %{HTTP_REFERER} !^$ RewriteCond %{HTTP_REFERER} !^http://www.mysite.com/.*$ [NC] RewriteCond %{HTTP_REFERER} !^http://www.mysite.com$ [NC] RewriteRule .*\.(jpg|jpeg|gif|png|bmp|swf)$ http://www.google.com/ [R,NC] RewriteCond %{REQUEST_FILENAME} !-f RewriteCond %{REQUEST_FILENAME} !-d RewriteRule . /index.php [L] </IfModule> # END WordPress I found some code to do that in google, and I just copied to .htacces since I'm not an expert in apache. It works, but I don't know if that is the best way to do it. How can I see if that is the reason why the server is slow? Are there any tools to monitor it? What would you do guys? Thanks in advance!

  Read the article

• The Network folder specified is currently mapped using a different user name and password

  - by Frank Thornton

  I have a NAS device, it has 3 shares. On one computer I have access to all 3 of the shares. On another computer I keep getting this error when try and add a 2nd one. The Network folder specified is currently mapped using a different user name and password [...] That is the message I keep getting. What causes that? EDIT: Every share has it's own username and password. EDIT: NET USE on the one running 3 from the same NAS device New connections will be remembered. Status Local Remote Network ------------------------------------------------------------------------------- OK T: \\192.168.2.5\SHARE1 Microsoft Windows Network OK X: \\Nas-1dsho-abc\SHARE2 Microsoft Windows Network Disconnected Y: \\192.168.2.9\backups Microsoft Windows Network OK Z: \\Nas-1dsho-abc\cbackups Microsoft Windows Network The command completed successfully. NET USE on the other: New connections will be remembered. Status Local Remote Network ------------------------------------------------------------------------------- OK Y: \\192.168.2.5\SHARE1 Microsoft Windows Network Unavailable Z: \\192.168.2.5\SHARE2 Microsoft Windows Network The command completed successfully.

  Read the article

• Haproxy and CNAME

  - by user123354

  I want to create a simple load balancer for the two servers. The problem is with CNAME records, I think. Let's say I have two the same applications on AppFog.com. app1.aws.af.cm and app2.aws.af.cm Here is my haproxy.cfg file: global maxconn 2000 daemon defaults mode http clitimeout 60000 srvtimeout 30000 contimeout 4000 option httpclose listen http_proxy bind [myip]:80 mode http stats enable stats auth user:passwd stats uri /stats balance source option httpchk option forwardfor server host01 app1.aws.af.cm:80 maxconn 300 check server host02 app2.aws.af.cm:80 maxconn 300 check But this only resolving IP for domain app1.aws.af.cm and app2.aws.af.cm, which obviously doesn't work if I open this IP in web browser. The problem is that AppFog doesn't have public IP for application (same as OpenShift). How to do that Haproxy to perform a proper connection between Load Balancer and this two servers? Example: This is real app - http://freechat.eu01.aws.af.cm Haproxy only resolves IP for this domain which is 46.51.204.8:80 Of course this IP will not show my application, only an error page. Sorry for my poor English.

  Read the article

• Resize a RAID 1 volume on OS X Snow Leopard - how? (Note: software raid)

  - by Emmel

  I've scoured the Internet in search of an answer to this question, and as usual with OSX-related topics, I often don't find any deep-dive technical explanations sufficient enough to feel confident doing dangerous things. Here is my question: I have a Mac Pro, running OS X 10.6.2. I have, as my main root/boot disk, a RAID 1 volume called "Mirror1". Mirror1 is comprised of two 1 TB disks. Mirror1, however, is fixed at 640 GB. That's because, I originally took a 640GB disk, bought a terabyte disk, mirrored it (using diskutil appleraid enable), when it synced I removed the 640GB and replaced it with a second 1 TB disk, and synced again. Voila! A single 640 GB replaced by two 1 TB disks in a mirror.. Actually, no. There's still something missing from the equation: Mirror1 needs to be expanded from 640GB to 1 TB to match the partition sizes on each of those disks. How do I do this? Perhaps the diskutil output will help: -> diskutil list /dev/disk0 #: TYPE NAME SIZE IDENTIFIER 0: GUID_partition_scheme *1.0 TB disk0 1: EFI 209.7 MB disk0s1 2: Apple_RAID 999.9 GB disk0s2 3: Apple_Boot Boot OSX 134.2 MB disk0s3 /dev/disk1 #: TYPE NAME SIZE IDENTIFIER 0: GUID_partition_scheme *1.0 TB disk1 1: EFI 209.7 MB disk1s1 2: Apple_RAID 999.9 GB disk1s2 3: Apple_Boot Boot OSX 134.2 MB disk1s3 /dev/disk2 #: TYPE NAME SIZE IDENTIFIER 0: GUID_partition_scheme *640.1 GB disk2 1: EFI 209.7 MB disk2s1 2: Apple_HFS Mac Disk 2 536.7 GB disk2s2 3: Microsoft Basic Data BOOTCAMP 103.1 GB disk2s3 /dev/disk3 #: TYPE NAME SIZE IDENTIFIER 0: Apple_HFS Mirror1 *639.8 GB disk3 -> diskutil appleraid list AppleRAID sets (1 found) =============================================================================== Name: Macintosh HD Unique ID: 1953F864-B474-4EB6-8E69-41834EBD0247 Type: Mirror Status: Online Size: 639.8 GB (639791038464 Bytes) Rebuild: manual Device Node: disk3 ------------------------------------------------------------------------------- # Device Node UUID Status ------------------------------------------------------------------------------- 0 disk1s2 25109BAE-5697-40EA-B612-0217851444F7 Online 1 disk0s2 11B83AB0-8148-4DB6-8761-DEF08C855F8D Online =============================================================================== Thanks in advance.

  Read the article

• Turn off gzip for a location in Nginx

  - by Nyxynyx

  How can gzip be turned off for a particular location and all its sub-directories? My main site is at http://mydomain.com and I want to turn gzip off for both http://mydomain.com/foo and http://mydomain.com/foo/bar. gzip is turned on in nginx.conf. I tried turning off gzip as shown below, but the Response Headers in Chrome's dev tools shows that Content-Encoding:gzip. How should gzip/output buffering be disabled properly? Attempt: server { listen 80; server_name www.mydomain.com mydomain.com; access_log /var/log/nginx/access.log; error_log /var/log/nginx/error.log; root /var/www/mydomain/public; index index.php index.html; location / { gzip on; try_files $uri $uri/ /index.php?$args ; } location ~ \.php$ { fastcgi_pass unix:/var/run/php5-fpm.sock; fastcgi_index index.php; include fastcgi_params; fastcgi_read_timeout 300; } location /foo/ { gzip off; try_files $uri $uri/ /index.php?$args ; } }

  Read the article

• SSL wildcard certificates and trailing 'www'

  - by user173326

  I've got a wildcard SSL certificate for *.mydomain.com. I'm using nginx, and redirecting all traffic for http to https, and also rewriting the URLs without a trailing www (if there is one). So it has, 1) http://subdomain.mydomain.com ---> https://subdomain.mydomain.com 2) http://www.subdomain.mydomain.com ---> https://subdomain.mydomain.com 3) https://www.subdomain.mydomain.com ---> https://subdomain.mydomain.com 4) https://subdomain.mydomain.com ---> https://subdomain.mydomain.com However, since my cert is for *.mydomain.com, case 3 gets an SSL error in chrome ('This is probably not the site that you are looking for!'), but if you click through it gets redirected and all is well. I understand why, since the initial connection is for https with a www (2 levels of subdomains), which doesn't match what is on the wildcard certificate. I thought a solution would be to get an additional cert for *.*.mydomain.com to cover www.*.mydomain.com. But it seems like that won't work. I spoke to agents from namecheap and comodo, and both said *.*.mydomain.com was not possible. I also came across this: https://support.quovadisglobal.com/KB/a60/will-ssl-work-with-multilevel-wildcards.aspx Is there a solution to this? To be able to cover www.*.mydomain.com?

  Read the article

• Excel 2007 - Adding line breaks in a cell and no line over 50 characters

  - by Richard Drew

  I have notes stored in an excel cell. I add line breaks and dates every time I add a new note. I need to copy this to another program, but it has a line limit of 50 characters. I want a line break for each new date and for when each date's comment goes over 50 characters. I'm able to do one or the other, but I can't figure out how to do both. I'd prefer words not to be split up, but at this point I don't care. Below is some sample input. If needed for a SUBSTITUTE or REPLACE function, I could add a ~ before each date in my input as a delimiter. Sample Input: 07/03 - FU on query. Copies and history included. CC to Jane Doe and John Public 06/29 - Cust claiming not to have these and wrong PO on query form. Responded with inv sent dates and locations, correct PO values, and copies. 06/27 - New ticket opened using query form 06/12 - Opened ticket with helpdesk asking status 05/21 - Copy submitted to [email protected] 05/14 - Copy sent to John Public and [email protected] Ideal Output: 07/03 - FU on query. Copies and history included. CC to Jane Doe and John Public 06/29 - Cust claiming not to have these and wrong PO on query form. Responded with inv sent dates an d locations, correct PO values, and copies. 06/27 - New ticket opened using query form 06/12 - Opened ticket with helpdesk asking status 05/21 - Copy submitted to [email protected] om 05/14 - Copy sent to John Public and email@custome r.com

  Read the article

• Domain workstation acting up and I can't track it down.

  - by DevNULL

  I have a developer with a Windows XP (SP2) 64 bit machine. If the machine is left on overnight (or any period of time longer than 5-6 hours) it takes 2-3 minutes to open any local drive and his network drives are no longer accessible. Here's what the system logs report... Any Help BTW: The problem just started a week ago and nothing has changed on the domain controller / AD or his machine. --- ERROR 1 Event Type: Error Event Source: NETLOGON Event Category: None Event ID: 5719 Date: 6/8/2010 Time: 9:17:26 AM User: N/A Computer: BFC1 Description: This computer was not able to set up a secure session with a domain controller in domain UR due to the following: There are currently no logon servers available to service the logon request. This may lead to authentication problems. Make sure that this computer is connected to the network. If the problem persists, please contact your domain administrator. ADDITIONAL INFO If this computer is a domain controller for the specified domain, it sets up the secure session to the primary domain controller emulator in the specified domain. Otherwise, this computer sets up the secure session to any domain controller in the specified domain. For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp. Data: 0000: 5e 00 00 c0 ^..A --- ERROR 2 The machine-default permission settings do not grant Local Activation permission for the COM Server application with CLSID {555F3418-D99E-4E51-800A-6E89CFD8B1D7} to the user NT AUTHORITY\LOCAL SERVICE SID (S-1-5-19). This security permission can be modified using the Component Services administrative tool. For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp. --- ERROR 3 Event Type: Error Event Source: RemoteAccess Event Category: None Event ID: 20106 Date: 6/8/2010 Time: 10:12:18 AM User: N/A Computer: BFC1 Description: Unable to add the interface {E76F0A78-7A0B-4EBB-A081-BA3BD452FC4C} with the Router Manager for the IP protocol. The following error occurred: Cannot complete this function. For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp. Data: 0000: eb 03 00 00 e...

  Read the article

• My system administrator set up 2 databases that sync. Master-Master. However, these two databases a

  - by Alex

  DB1 and DB2. I made changes to DB1, and it does not seem to be on DB2. When I do "SHOW SLAVE STATUS\G" on DB2, there seems to be an error: mysql> show slave status\G *************************** 1. row *************************** Slave_IO_State: Waiting for master to send event Master_Host: Master_User: Master_Port: Connect_Retry: 60 Master_Log_File: mysql-bin.0005496 Read_Master_Log_Pos: 5445649315 Relay_Log_File: mysqld-relay-bin.0041705 Relay_Log_Pos: 1624302119 Relay_Master_Log_File: mysql-bin.0004461 Slave_IO_Running: Yes Slave_SQL_Running: No Replicate_Do_DB: Replicate_Ignore_DB: Replicate_Do_Table: Replicate_Ignore_Table: Replicate_Wild_Do_Table: Replicate_Wild_Ignore_Table: Last_Errno: 1062 Last_Error: Error 'Duplicate entry '4779' for key 1' on query. Default database: 'falc'. Query: 'INSERT INTO `log` (`anon_id`, `created_at`, `query`, `episode_url`, `detail_id`, `ip`) VALUES ('fdzn1d45kMavF4qbyePv', '2009-11-19 04:19:13', 'amazon', '', '', '130.126.40.57')' Skip_Counter: 0 Exec_Master_Log_Pos: 162301982 Relay_Log_Space: 136505187184 Until_Condition: None Until_Log_File: Until_Log_Pos: 0 Master_SSL_Allowed: No Master_SSL_CA_File: Master_SSL_CA_Path: Master_SSL_Cert: Master_SSL_Cipher: Master_SSL_Key: Seconds_Behind_Master: NULL 1 row in set (0.00 sec) Then, I did show tables, and it seems like DB2 is lacking a table that I created on DB1...that means that for some reason, DB2 stopped syncing with DB1. How can I simply allow them to be in full synchronization again? All I want is DB2 to be exactly the same as DB1!

  Read the article

• Kickstart: Serve dynamic kickstart images via a CGI or PHP script?

  - by Stefan Lasiewski

  I'd like to kickstart a couple dozen RHEL6/SL6 servers. However, some of these servers are different and I don't want to create a new ks.cfg file for each class of server. Are there any products which can generate a Kickstart file dynamically on the fly, from a template? For example, if I append a line like this to the KERNEL: APPEND ks=http://192.168.1.100/cgi-bin/ks.cgi Then the script ks.cgi can determine what host this is (Via the MAC address), and print out Kickstart options which are appropriate for that host. I could optionally override some options by passing parameters to the script, like this: APPEND ks=http://192.168.1.100/cgi-bin/ks.cgi?NODETYPE=production&IP=192.168.2.80 After we kickstart the server, we activate Cfengine/Puppet on this system and manage the system using our favorite Configuration Management product. We're experimenting with xCAT but it is proving too cumbersome. I've looked into Cobbler, but I'm not sure it does this. Update: A roll-your-own solution is discussed in the O'Reilly book: Managing RPM-Based Systems with Kickstart and Yum, Chapter 3. Customizing Your Kickstart Install Dynamic ks.cfg, which echos some of the comments in this thread: To implement such a tool is beyond the scope of this Short Cut, but I can walk through the high-level design. Any such solution would mix a data store (the things that change) with a templating solution (the things that don’t change). The data store would hold the per-machine data, such as the IP address and hostname. You would also need a unique identifier, perhaps the hostname, such that you could pick up a given machine’s data. The data store could be a flat file, XML data, or a relational database such as PostgreSQL or MySQL. In turn, to invoke the system, you pass a machine’s unique identifier as a URL parameter. For example: boot: linux ks=http://your.kickstart.server/gen_config?host-server25 In this example, the CGI (or servlet, or whatever) generates a ks.cfg for the machine server25. But where, oh where, is the code for ks.cgi?

  Read the article

• Linux - real-world hardware RAID controller tuning (scsi and cciss)

  - by ewwhite

  Most of the Linux systems I manage feature hardware RAID controllers (mostly HP Smart Array). They're all running RHEL or CentOS. I'm looking for real-world tunables to help optimize performance for setups that incorporate hardware RAID controllers with SAS disks (Smart Array, Perc, LSI, etc.) and battery-backed or flash-backed cache. Assume RAID 1+0 and multiple spindles (4+ disks). I spend a considerable amount of time tuning Linux network settings for low-latency and financial trading applications. But many of those options are well-documented (changing send/receive buffers, modifying TCP window settings, etc.). What are engineers doing on the storage side? Historically, I've made changes to the I/O scheduling elevator, recently opting for the deadline and noop schedulers to improve performance within my applications. As RHEL versions have progressed, I've also noticed that the compiled-in defaults for SCSI and CCISS block devices have changed as well. This has had an impact on the recommended storage subsystem settings over time. However, it's been awhile since I've seen any clear recommendations. And I know that the OS defaults aren't optimal. For example, it seems that the default read-ahead buffer of 128kb is extremely small for a deployment on server-class hardware. The following articles explore the performance impact of changing read-ahead cache and nr_requests values on the block queues. http://zackreed.me/articles/54-hp-smart-array-p410-controller-tuning http://www.overclock.net/t/515068/tuning-a-hp-smart-array-p400-with-linux-why-tuning-really-matters http://yoshinorimatsunobu.blogspot.com/2009/04/linux-io-scheduler-queue-size-and.html For example, these are suggested changes for an HP Smart Array RAID controller: echo "noop" > /sys/block/cciss\!c0d0/queue/scheduler blockdev --setra 65536 /dev/cciss/c0d0 echo 512 > /sys/block/cciss\!c0d0/queue/nr_requests echo 2048 > /sys/block/cciss\!c0d0/queue/read_ahead_kb What else can be reliably tuned to improve storage performance? I'm specifically looking for sysctl and sysfs options in production scenarios.

  Read the article

• lighttpd with multiple IPs, each with a UCC certificate and many hostnames

  - by Dave

  I'd like to get lighttpd working with UCC certificates, but I can't seem to figure out the correct syntax. Essentially, for each IP address, I have one UCC certificate and a bunch of hostnames. $SERVER["socket"] == "10.0.0.1:443" { ssl.engine = "enable" ssl.ca-file = "/etc/ssl/certs/the.ca.cert.pem" ssl.pemfile = "/etc/ssl/private/websitegroup1.com.pem" $HTTP["host"] =~ "mywebsite.com" { server.document-root = /var/www/mywebsite.com/htdocs" } The above code works fine for one hostname, but as soon as I try to set up another hostname (note the same SSL cert): $SERVER["socket"] == "10.0.0.1:443" { ssl.engine = "enable" ssl.ca-file = "/etc/ssl/certs/the.ca.cert.pem" ssl.pemfile = "/etc/ssl/private/websitegroup1.com.pem" $HTTP["host"] =~ "anotherwebsite.com" { server.document-root = /var/www/anotherwebsite.com/htdocs" } ...I get this error: Duplicate config variable in conditional 6 global/SERVERsocket==10.0.0.1:443: ssl.engine Is there any way I can put a conditional so that only if ssl.engine is not already enabled, enable it? Or do I have to put all my $HTTP["host"]s inside the same $SERVER["socket"] (which will make config file management more difficult for me) or is there some entirely different way to do it? This has to be repeated for multiple IPs too (so I'll have a bunch of SERVER["socket"] == 10.0.0.2:443" etc), each with one UCC cert and many hostnames. Am I going about this the wrong way entirely? My goal is to conserve IP addresses when I have many websites that are related and can share an SSL certificate, but still need their own SSL-accessible version from the appropriate hostname (instead of a single secure.mywebsite.com).

  Read the article

• why does mysql have so many more open and fragmented tables than tables in the DB?

  - by kswift

  I've been working making our database run a little smoother and had good results over the past week. But there are still some things I dont understand. For one thing, the database has 25 tables. But mysql status shows 512 are open: mysqladmin status Uptime: 212854 Threads: 1 Questions: 43041 Slow queries: 7 Opens: 2605 Flush tables: 1 Open tables: 512 Queries per second avg: 0.202 I've read that isam opens extra file descriptors and a few other reasons why the number of open tables might be higher than 25, but I am guessing that 512 is not a good thing. Any suggestions on why this might be or what I should be looking into? I've also been using mysqltuner and its been helpful. But it has consistently listed the number of fragmented tables at 207. In phpmyadmin I've selected all the tables and optimized them several times. It hasn't reduced the number of fragmented tables that mysqltuner reports. I think I am missing some important concept about how this all works. Does anyone have any suggestions to point me in the right direction or narrow down google searches or just generally help me be less clueless? Thanks!

  Read the article

• How can I cornify a SharePoint site?

  - by Chris Farmer

  Inspired by the April 1 gravatar changes and the memory of last year's cornification of Stack Overflow, I wanted to add a cornify button to my company's SharePoint app. I just added their html snippet to a Content Editor Web Part. <a href="http://www.cornify.com" onclick="cornify_add();return false;"> <img src="http://www.cornify.com/assets/cornifycorn.gif" width="52" height="51" border="0" alt="Cornify" /> </a><script type="text/javascript" src="http://www.cornify.com/js/cornify.js"></script> The button renders all glittery and beautiful, and the magical functionality works fine in Chrome and Firefox (I'm on Windows 7) for me. But, in IE8, all the gorgeous unicorn images get added at the bottom of the page such that you can't see them unless you scroll down. Since most of our users are IE users, I fear that this just isn't going to be all that much fun. So, is there some known way to force this to work better in IE8, or is there another similarly fun site adornment utility that I could use that might behave better in a SharePoint 2007 app running in IE7/8?

  Read the article

• Need Help getting perl module DBD::mysql installed for bugzilla on RedHat.

  - by Alos Diallo

  Hi everyone I am having some issues getting Bugzilla setup, I have the software on the server and am trying to get the pre-rec's setup. I am using RedHat 4.1.2-42. I have all of the required perl modules save one:DBD::mysql When I try: sudo perl install-module.pl DBD::mysql I get the following response(this is only an excerpt): rm -f blib/arch/auto/DBD/mysql/mysql.so LD_RUN_PATH="/usr/lib64/mysql:/usr/lib64:/lib64" /usr/bin/perl myld gcc -shared -O2 -g -pipe -Wall -Wp,-D_FORTIFY_SOURCE=2 -fexceptions -fstack-protector --param=ssp-buffer-size=4 -m64 -mtune=generic dbdimp.o mysql.o -o blib/arch/auto/DBD/mysql/mysql.so \ -L/usr/lib64/mysql -lmysqlclient -lz -lcrypt -lnsl -lm -L/usr/lib64 -lssl -lcrypto \ /usr/bin/ld: skipping incompatible /usr/lib/libssl.so when searching for -lssl /usr/bin/ld: skipping incompatible /usr/lib/libssl.a when searching for -lssl /usr/bin/ld: cannot find -lssl collect2: ld returned 1 exit status make: * [blib/arch/auto/DBD/mysql/mysql.so] Error 1 /usr/bin/make -- NOT OK Running make test Can't test without successful make Running make install make had returned bad status, install seems impossible I then tried the following: CFLAGS="-I/usr/lib64/mysql:/usr/lib64:/lib64" perl install-module.pl DBD::mysql I get the same result. I have also tried to install it using CPAN but also get the same result. Right now I have DBD-mysql v3.0007 but need (v4.00) Also when I try to install open ssl it says I have the latest version. Does anyone know what I have to do to get this to work? Any help would be greatly appreciated. Thank you

  Read the article

• pfSense Load Balancer and Virtual IP

  - by jshin47

  I have two identical web servers on 10.2.1.13 and 10.2.1.113. I would like to set up pfSense load balancer to balance requests to both of these. I set up pools that included HTTP and HTTPS for both of these hosts, then set up virtual servers that responded on HTTP and HTTPS and referred traffic to its respective pool. However, I set up the virtual server to listen on 10.2.1.213, a LAN IP rather than a WAN IP, because I want LAN traffic to be able use the load balancer virtual server as well. So, I set up a Virtual IP for 10.2.1.213 on LAN IP, and a NAT port forwarding rule for HTTP and HTTPS traffic on a WAN IP to forward to 10.2.1.213. It seems like this should work, but it fails. What eventually happens is that when I try to access the page from WAN, I am directed to the login page for my pfSense device rather than the page I am expecting. When I try to access 10.2.1.213 from LAN, the request times out. What is going wrong here? I have tried it with and without NAT reflection to no avail. Please advise

  Read the article

• Trouble getting latest version of Git

  - by TheMethod

  I am using Ubuntu 10.04 LTS. I'm looking at using git as source control for personal projects and Github as a remote repository. I was having trouble pushing a commit to my remote github repo getting the following error message: The requested URL returned error: 403 while accessing https://github.com/Jstall/helloworld.git/info/refs When I did some digging I found that the problem could be me not having the latest version of Git. When I did a --version I found that I have version 1.7.0.4 locally. So I tried to update git using: sudo apt-get install git but get the following error: Reading package lists... Done Building dependency tree Reading state information... Done Package git is not available, but is referred to by another package. This may mean that the package is missing, has been obsoleted, or is only available from another source E: Package git has no installation candidate I've tried running: sudo apt-get update and trying again but it didn't seem to make a difference. I'm not sure if it's relevant but I'm also getting a couple of 404's when I run update: Err http://wine.budgetdedicated.com edgy/main Packages 404 Not Found Fetched 4,117B in 0s (5,142B/s) W: Failed to fetch http://us.archive.ubuntu.com/ubuntu/dists/edgy/universe/binary-i386/Packages.gz 404 Not Found [IP: 91.189.91.15 80] W: Failed to fetch http://wine.budgetdedicated.com/apt/dists/edgy/main/binary-i386/Packages.gz 404 Not Found I'm not sure when I should try next. Could anyone suggest a course of action to get this resolved? Any advice would be appreciated. Thanks much!

  Read the article

• File Replication Service Errors

  - by ekamtaj

  Hey Guys, We have a windows 2003 r2 server and couple of the users are reporting that they can not scan files into the windwos server. They are getting an Out of Space errors. I took a look at the server and we have 600GB free disk space on that partition. But while looking at the event log I found a lot of errors like (13552,13555) The File Replication Service is unable to add this computer to the following replica set: "DOMAIN SYSTEM VOLUME (SYSVOL SHARE)" This could be caused by a number of problems such as: -- an invalid root path, -- a missing directory, -- a missing disk volume, -- a file system on the volume that does not support NTFS 5.0 The information below may help to resolve the problem: Computer DNS name is "server.domain.local" Replica set member name is "server" Replica set root path is "c:\windows\sysvol\domain" Replica staging directory path is "c:\windows\sysvol\staging\domain" Replica working directory path is "c:\windows\ntfrs\jet" Windows error status code is FRS error status code is FrsErrorMismatchedJournalId Other event log messages may also help determine the problem. Correct the problem and the service will attempt to restart replication automatically at a later time. For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp.

  Read the article

• Squid: The request or reply is too large

  - by Ueli

  I have done a reverse proxy with an Apache in the background (on the same server). All works great but I can't open one page. I get the error "The request or reply is too large." In my cache.log contains: 2010/12/09 15:28:29| WARNING: http.c:971: HTTP header too large 2010/12/09 15:29:03| ctx: enter level 0: 'http://server/admin/cms/nav' 2010/12/09 15:29:03| httpProcessReplyHeader: Too large reply header 2010/12/09 15:29:03| ctx: exit level 0 In my squid.conf i disabled the limitations of the request and reply header, without success: reply_body_max_size 0 allow all request_body_max_size 0 Does someone know why that don't work? Thank you very much. Squid Version: Squid Cache: Version 2.7.STABLE3 configure options: '--prefix=/usr' '--exec_prefix=/usr' '--bindir=/usr/sbin' '--sbindir=/usr/sbin' '--libexecdir=/usr/lib/squid' '--sysconfdir=/etc/squid' '--localstatedir=/var/spool/squid' '--datadir=/usr/share/squid' '--enable-async-io' '--with-pthreads' '--enable-storeio=ufs,aufs,coss,diskd,null' '--enable-linux-netfilter' '--enable-arp-acl' '--enable-epoll' '--enable-removal-policies=lru,heap' '--enable-snmp' '--enable-delay-pools' '--enable-htcp' '--enable-cache-digests' '--enable-underscores' '--enable-referer-log' '--enable-useragent-log' '--enable-auth=basic,digest,ntlm,negotiate' '--enable-negotiate-auth-helpers=squid_kerb_auth' '--enable-carp' '--enable-follow-x-forwarded-for' '--with-large-files' '--with-maxfd=65536' 'amd64-debian-linux' 'build_alias=amd64-debian-linux' 'host_alias=amd64-debian-linux' 'target_alias=amd64-debian-linux' 'CFLAGS=-Wall -g -O2' 'LDFLAGS=' 'CPPFLAGS='

  Read the article

• What steps to take when CPAN installation fails?

  - by pythonic metaphor

  I have used CPAN to install perl modules on quite a few occasions, but I've been lucky enough to just have it work. Unfortunately, I was trying to install Thread::Pool today and one of the required dependencies, Thread::Converyor::Monitored failed the test: Test Summary Report ------------------- t/Conveyor-Monitored02.t (Wstat: 65280 Tests: 89 Failed: 0) Non-zero exit status: 255 Parse errors: Tests out of sequence. Found (2) but expected (4) Tests out of sequence. Found (4) but expected (5) Tests out of sequence. Found (5) but expected (6) Tests out of sequence. Found (3) but expected (7) Tests out of sequence. Found (6) but expected (8) Displayed the first 5 of 86 TAP syntax errors. Re-run prove with the -p option to see them all. Files=3, Tests=258, 6 wallclock secs ( 0.07 usr 0.03 sys + 4.04 cusr 1.25 csys = 5.39 CPU) Result: FAIL Failed 1/3 test programs. 0/258 subtests failed. make: *** [test_dynamic] Error 255 ELIZABETH/Thread-Conveyor-Monitored-0.12.tar.gz /usr/bin/make test -- NOT OK //hint// to see the cpan-testers results for installing this module, try: reports ELIZABETH/Thread-Conveyor-Monitored-0.12.tar.gz Running make install make test had returned bad status, won't install without force Failed during this command: ELIZABETH/Thread-Conveyor-Monitored-0.12.tar.gz: make_test NO What steps do you take to start seeing why an installation failed? I'm not even sure how to begin tracking down what's wrong.

  Read the article

• Sparing level on HP EVA 4000

  - by Samuel

  One of the disks of our EVA4000 died today. This diskgroup (all volumes vraid5 with sparing level 1 and almost no space left for more volumes, 1TiB drives) is being rebuilt with "spare space" right now, and it will take at least 15 hours to do the leveling/rebuilding. We can't get a new disk until Friday. So, the question is, what would happen if another disk dies before the leveling completes? Would we lose data? And after that, how many aditional disks could die before losing data? 1 or 2? In "usual" RAID, we would be vulnerable to data loss while the rebuild takes place, but in this case the space reserved for sparing is two times the size of the bigger disk, so at the very least the effect should be the same of having two spares. Thanks in advance. Update: I have found some interesting threads about this question but still can't answer to this question, so I'm starting a bounty. http://blog.thestoragearchitect.com/2008/10/27/understanding-eva/ http://www.google.com/url?sa=t&rct=j&q=&esrc=s&source=web&cd=1&url=http%3A%2F%2Fwww.experts-exchange.com%2FStorage%2FStorage_Technology%2FQ_25548177.html (Expert Exchange question from google).

  Read the article

• Postfix misconfigured? 550 Sender rejected from recieving server

  - by wnstnsmth

  We use Postfix on our CentOS 6 machine, having the following configuration. We use PHP's mail() function to send rudimentary password reset emails, but there is a problem. As you will see, mydomain and myhostname is correctly set, afaik. alias_database = hash:/etc/aliases alias_maps = hash:/etc/aliases command_directory = /usr/sbin config_directory = /etc/postfix daemon_directory = /usr/libexec/postfix data_directory = /var/lib/postfix debug_peer_level = 2 html_directory = no inet_interfaces = localhost inet_protocols = all mail_owner = postfix mailq_path = /usr/bin/mailq.postfix manpage_directory = /usr/share/man mydestination = $myhostname, localhost.$mydomain, localhost mydomain = ***.ch myhostname = test.***.ch newaliases_path = /usr/bin/newaliases.postfix queue_directory = /var/spool/postfix readme_directory = /usr/share/doc/postfix-2.6.6/README_FILES sample_directory = /usr/share/doc/postfix-2.6.6/samples sendmail_path = /usr/sbin/sendmail.postfix setgid_group = postdrop unknown_local_recipient_reject_code = 550 Now this is the stuff that is in the /var/log/maillog of Postfix upon sending an email to ***.***@***.ch, with ***.ch being the same domain our sending server test.***.ch is on: Dec 13 16:55:06 R12X0210 postfix/pickup[6831]: E6D6311406AB: uid=48 from=<apache> Dec 13 16:55:06 R12X0210 postfix/cleanup[6839]: E6D6311406AB: message-id=<20121213155506.E6D6311406AB@test.***.ch> Dec 13 16:55:07 R12X0210 postfix/qmgr[6832]: E6D6311406AB: from=<apache@test.***.ch>, size=1276, nrcpt=1 (queue active) Dec 13 16:55:52 R12X0210 postfix/smtp[6841]: E6D6311406AB: to=<***.***@***.ch>, relay=mail.***.ch[**.**.249.3]:25, delay=46, delays=0.18/0/21/24, dsn=5.0.0, status=bounced (host mail.***.ch[**.**.249.3] said: 550 Sender Rejected (in reply to RCPT TO command)) Dec 13 16:55:52 R12X0210 postfix/cleanup[6839]: 8562C11406AC: message-id=<20121213155552.8562C11406AC@test.***.ch> Dec 13 16:55:52 R12X0210 postfix/bounce[6848]: E6D6311406AB: sender non-delivery notification: 8562C11406AC Dec 13 16:55:52 R12X0210 postfix/qmgr[6832]: 8562C11406AC: from=<>, size=3065, nrcpt=1 (queue active) Dec 13 16:55:52 R12X0210 postfix/qmgr[6832]: E6D6311406AB: removed Dec 13 16:55:52 R12X0210 postfix/local[6850]: 8562C11406AC: to=<root@test.***.ch>, orig_to=<apache@test.***.ch>, relay=local, delay=0.13, delays=0.07/0/0/0.05, dsn=2.0.0, status=sent (delivered to mailbox) Dec 13 16:55:52 R12X0210 postfix/qmgr[6832]: 8562C11406AC: removed So the receiving server rejects the sender (line 4 of log output). We have tested it with one other recipient and it worked, so this problem might be completely unrelated to our settings, but related to the recipient. Still, with this question, I want to make sure we're not making an obvious misconfiguration on our side.

  Read the article

• converting a png with an ICC profile?

  - by jedierikb

  I can convert a jpg from one ICC to another ICC. convert rgb_image.jpg -profile USCoat.icm cmyk_image.jpg Or I can convert a jpg with no ICC to another ICC. convert rgb_image.jpg +profile icm \ -profile sRGB.icc -profile USCoat.icm cmyk_image.jpg But how do I convert a png's pixels into the gamut described by an ICC profile? I understand I cannot embed the profile into the image file, but would at least like to convert the colors. When I reuse the above commands, the colors come out wrong... (different from the colors in the JPG when converted). This is the source image: http://alumni.media.mit.edu/~erikb/tmp/RED_JPG.jpg And here is what I am trying: convert RED_JPG.jpg +profile icm -profile sRGB_v4_ICC_preference.icc -profile USWebUncoated.icc CMYK_PNG.png and this is what I am getting: http://alumni.media.mit.edu/~erikb/tmp/CMYK_PNG.png I was hoping to get an image with the same colors as a JPEG run through the same command: convert RED_JPG.jpg +profile icm -profile sRGB_v4_ICC_preference.icc -profile USWebUncoated.icc CMYK_JPG.jpg resulting in: http://alumni.media.mit.edu/~erikb/tmp/CMYK_JPG.jpg *this image, CMYK_JPG.jpg, is what I am trying to reproduce pixel by pixel in a PNG file.* Any suggestions? Original (unanswered) post here.

  Read the article

• Allignment of ext3 partition on LVM RAID volume group

  - by John P

  I'm trying to add a partition on a LVM that resides on a RAID6 volume group and fdisk is complaining about the partition not residing on a physical sector boundry. My question is, how do you calculate the correct starting sector for a partition on a LVM? This partition will be formated ext3. Would it be better to just format the LVM directly instead of creating a new partition? Disk /dev/dedvol/backup: 2199.0 GB, 2199023255552 bytes 255 heads, 63 sectors/track, 267349 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 1048576 bytes / 8388608 bytes Disk identifier: 0x4e428f49 Device Boot Start End Blocks Id System /dev/dedvol/backup1 63 267349 2146982827+ 83 Linux Partition 1 does not start on physical sector boundary. lvdisplay /dev/dedvol/backup --- Logical volume --- LV Name /dev/dedvol/backup VG Name dedvol LV UUID OV2n5j-7LHb-exJL-t8dI-dU8A-2vxf-uIicCt LV Write Access read/write LV Status available # open 0 LV Size 2.00 TiB Current LE 524288 Segments 1 Allocation inherit Read ahead sectors auto - currently set to 32768 Block device 253:1 vgdisplay dedvol --- Volume group --- VG Name dedvol System ID Format lvm2 Metadata Areas 1 Metadata Sequence No 3 VG Access read/write VG Status resizable MAX LV 0 Cur LV 2 Open LV 1 Max PV 0 Cur PV 1 Act PV 1 VG Size 14.55 TiB PE Size 4.00 MiB Total PE 3815448 Alloc PE / Size 3670016 / 14.00 TiB Free PE / Size 145432 / 568.09 GiB VG UUID 8fBcOk-aXGx-P3Qy-VVpJ-0zK1-fQgy-Cb691J

  Read the article

< Previous Page | 541 542 543 544 545 546 547 548 549 550 551 552  | Next Page >