Search Results

Search found 17448 results on 698 pages for 'regular expressions info'.

Page 555/698 | < Previous Page | 551 552 553 554 555 556 557 558 559 560 561 562  | Next Page >

• VMware NAS/iSCSI recommendations - smallish organization

  - by Bubnoff

  I have two VMware servers - ESX + ESXi. Two backup NAS boxes. The current NAS boxes are low-cost and unsuitable for running VMs from. Support NFS only. Slow. My plan is to have a dedicated iSCSI/NAS for storing and running VMs. Two additional low-cost boxes for backup. I'm looking for advice regarding 2 things really: Recommendations as far as VMware architecture/design for a smaller organization. Less than 20 Virtual Machines. 2 servers + 2 x 1.5 terabyte backup NAS boxes. A good NAS/iSCSI box with your recommendation on RAID config ...I would go with 6 or better. I'm trying to design an installation that is both fast and reliable/redundant. If you have any experiences to share or your current configuration including network design ( switches, fiber ...etc ), I will be enormously thankful. I'm not married to this idea, so if you have a design not using iSCSI NAS boxes ...let er rip. Cost? Can we stay around $5,000 ( on top of already stated components )? Links to info are welcome also. Thanks for reading! Bubnoff

  Read the article

• Not able to access external Hard disk

  - by Jash Jacob

  I have a 1TB External Hard drive which I'm currently not able to access. When I open the External drive in Finder, It shows it's empty. When I use the option to "Get Info", I get the dialog box stating it has about 300GB Free. Tried to get into the External Drive using Terminal, I had no luck. Checking in Disk Utility, It showed that I have many number of files but ZERO folder. I tried to "repair disk", in the process the external Drive got unmounted in between the process. I checked this drive on Windows. I was able to open almost all the folders but I wasn't able to copy anything onto the external drive. One folder caused my windows computer to hang, So i connected the drive back onto my MacBook Pro and tried to access the drive through terminal (this time it worked!) and then I tried to delete the folder with rm command, I got an "input/output error" What should i do to recover the files in that folder? How can i access my external drive on my mac

  Read the article

• Apache2 Re-Routing from Domain Name to Internal IP Address

  - by Richard Grey

  The problem that I am having, is that when someone goes to my domain name example.co.uk, for some reason, apache seems to be re-routing the request to the internal IP address of the server, i.e. 192.168.0.52 My Apache2 default sites enabled file is as follows: ServerAdmin [email protected] ServerName trusteeguard.co.uk ServerAlias www.trusteeguard.co.uk DocumentRoot /var/www <Directory /> Options FollowSymLinks AllowOverride All </Directory> <Directory /var/www/> Options Indexes FollowSymLinks MultiViews AllowOverride All Order allow,deny allow from all </Directory> ScriptAlias /cgi-bin/ /usr/lib/cgi-bin/ <Directory "/usr/lib/cgi-bin"> AllowOverride All Options +ExecCGI -MultiViews +SymLinksIfOwnerMatch Order allow,deny Allow from all </Directory> ErrorLog /var/log/apache2/trusteeguard-error.log # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. LogLevel warn CustomLog /var/log/apache2/trusteeguard-access.log combined Alias /doc/ "/usr/share/doc/" <Directory "/usr/share/doc/"> Options Indexes MultiViews FollowSymLinks AllowOverride All Order deny,allow Deny from all Allow from 127.0.0.0/255.0.0.0 ::1/128 </Directory> This is an Ubuntu box if that is any help ;)

  Read the article

• EC2 instances keep becoming inaccessible via SSH, can I use elastic loadbalancer to check SSH connectivity?

  - by Rick

  This is mainly an issue for my development ec2 server as it seems that my instance keeps becoming inaccessible via SSH. It happened yesterday so I killed that one and started a new one and happened again later today. The server still works, my web application is accessible in a web browser but whenever I try to connect via SSH I get a pemrission denied (public key) error message in my terminal. I am 100% sure I am doing nothing wrong as I can create a new instance of the exact same AMI (its a personal custom AMI), change absolutely nothing, including using the same .pem key, and then am able to SSH into that new instance using the exact same command as before (just changing the IP address). I understand that ec2 can have issues but having this happen every day seems a bit odd.. I am using an m2.xlarge instance so I don't know if these tend to be unstable, in the past I have used a small instance and had it running for months with no problems which is why I find this so odd. I am looking into using loadbalancing but it seems the only "health" checks they offer is for http or tcp so I'm not sure if I can make it monitor for SSH connectivity. This is important for development as I may make 1-2 new pushes of an application a day and use SSH to do this. I have a designer that needs to have the app always accessible as he works with the front-end files to test output with the live application. Anyways, any advice / info is appreciated

  Read the article

• Postfix message ID originating process?

  - by Anders Braüner Nielsen

  Last night my postfix mail server(Debian Squeeze with dovecot, roundcube, opendkim and spamassassin enabled) started sending out spam from a single domain of mine like these: $cat mail.log|grep D6930B76EA9 Jul 31 23:50:09 myserver postfix/pickup[28675]: D6930B76EA9: uid=65534 from=<[email protected]> Jul 31 23:50:09 myserver postfix/cleanup[27889]: D6930B76EA9: message-id=<[email protected]> Jul 31 23:50:09 myserver postfix/qmgr[7018]: D6930B76EA9: from=<[email protected]>, size=957, nrcpt=1 (queue active) Jul 31 23:50:09 myserver postfix/error[7819]: D6930B76EA9: to=<[email protected]>, relay=none, delay=0.03, delays=0.02/0/0/0, dsn=4.4.2, status=deferred (delivery temporarily suspended: lost connection with mta5.am0.yahoodns.net[66.196.118.33] while sending RCPT TO) The domain in question did not have any accounts enabled but only a catchall alias set through postfixadmin - most emails were send from a specific address I use frequently but some were also sent from bogus addresses. None of the other virtual domains handled by postfix were affected. How can I find out what process was feeding postfix/sendmail or more info on where they originated? As far as I can tell php mail() wasn't used and I've run several open relay tests. I did a little tinkering(removed winbind from the server and ipv6 addresses from main.cf) after the attack and it seems to have subsided but I still have no idea how my server was suddenly sending out spam. Maybe I fixed it - maybe I didn't. Can anyone help figuring out how I was compromised? Anywhere else I should look? I've run Linux Malware Detect on recently changed files but nothing found.

  Read the article

• Can't connect to vsftpd on Ubuntu 10.04

  - by Johnny

  I started the vsftpd on Ubuntu 10.04, but can't connect to it. The error says(FTP Client): Status: Connecting to 124.205.xx.xx:21... Error: Connection timed out Error: Could not connect to server I've checked the server status, and vsftpd is running: $ ps ax | grep vsftpd 23646 ? Ss 0:00 /usr/sbin/vsftpd 23650 pts/1 S+ 0:00 grep --color=auto vsftpd port 21 is under listening as well: $ netstat -tlnp | grep 21 (No info could be read for "-p": geteuid()=1000 but you should be root.) tcp 0 0 0.0.0.0:21 0.0.0.0:* LISTEN - I can connect to localhost: $ ftp localhost Connected to localhost. 220 (vsFTPd 2.2.2) Name (localhost:jlee): 331 Please specify the password. Password: 230 Login successful. Remote system type is UNIX. Using binary mode to transfer files. ftp> Here is iptables output $ sudo iptables -vL Chain INPUT (policy ACCEPT 191 packets, 144K bytes) pkts bytes target prot opt in out source destination Chain FORWARD (policy ACCEPT 0 packets, 0 bytes) pkts bytes target prot opt in out source destination Chain OUTPUT (policy ACCEPT 124 packets, 28502 bytes) pkts bytes target prot opt in out source destination What's the problem here?

  Read the article

• Connect to Nonencrypted Wireless Network Using Ubuntu Commands

  - by Tim

  I failed to connect to an open i.e. nonencrypted wireless network using Ubuntu command lines. Here is what I did: $ sudo /etc/init.d/NetworkManager stop * Stopping network connection manager NetworkManager [ OK ] $ sudo /sbin/ifconfig wlan0 up $ sudo iwconfig wlan0 essid "Cavalier High-Speed 866-4-CAVTEL" $ sudo dhclient wlan0 There is already a pid file /var/run/dhclient.pid with pid 10812 killed old client process, removed PID file Internet Systems Consortium DHCP Client V3.1.1 Copyright 2004-2008 Internet Systems Consortium. All rights reserved. For info, please visit http://www.isc.org/sw/dhcp/ wmaster0: unknown hardware address type 801 wmaster0: unknown hardware address type 801 Listening on LPF/wlan0/00:0e:9b:cd:4e:18 Sending on LPF/wlan0/00:0e:9b:cd:4e:18 Sending on Socket/fallback DHCPREQUEST of 192.168.1.67 on wlan0 to 255.255.255.255 port 67 DHCPREQUEST of 192.168.1.67 on wlan0 to 255.255.255.255 port 67 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 7 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 7 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 8 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 12 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 21 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 6 No DHCPOFFERS received. Trying recorded lease 192.168.1.67 PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data. --- 192.168.1.1 ping statistics --- 1 packets transmitted, 0 received, +1 errors, 100% packet loss, time 0ms Trying recorded lease 192.168.1.45 PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data. --- 192.168.1.1 ping statistics --- 1 packets transmitted, 0 received, +1 errors, 100% packet loss, time 0ms No working leases in persistent database - sleeping. $ sudo /sbin/iwconfig wlan0 wlan0 IEEE 802.11bg Mode:Managed Frequency:2.422 GHz Access Point: Not-Associated Tx-Power=27 dBm Retry min limit:7 RTS thr:off Fragment thr=2352 B Encryption key:off Power Management:off Link Quality:0 Signal level:0 Noise level:0 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 I was wondering what the problem is and how I can do it right? Thanks and regards!

  Read the article

• Centos iptables configuration for Wordpress and Gmail smtp

  - by Fabrizio

  Let me start off by saying that I'm a Centos newby, so all info, links and suggestions are very welcome! I recently set up a hosted server with Centos 6 and configured it as a webserver. The websites running on it are nothing special, just some low traffic projects. I tried to configure the server as default as possible, but I like it to be secure as well (no ftp, custom ssh port). Getting my Wordpress to run as desired, I'm running into some connection problems. 2 things are not working: installing plugins and updates through ssh2 (failed to connect to localhost:sshportnumber) sending emails from my site using the Gmail smtp (Failed to connect to server: Permission denied (13)) I have the feeling that these are both related to the iptables configuration, because I've tried everything else (I think). I tried opening up the firewall to accept traffic for ports 465 (gmail smtp) and ssh port (lets say this port is 8000), but both the issues remain. Ssh connections from the terminal are working fine though. After each change I tried implementing I restarted the iptables service. This is my iptables configuration (using vim): # Generated by iptables-save v1.4.7 on Sun Jun 1 13:20:20 2014 *filter :INPUT ACCEPT [0:0] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [0:0] -A INPUT -m state --state RELATED,ESTABLISHED -j ACCEPT -A INPUT -p icmp -j ACCEPT -A INPUT -i lo -j ACCEPT -A INPUT -p tcp -m tcp --dport 8000 -j ACCEPT -A INPUT -p tcp -m tcp --dport 80 -j ACCEPT -A INPUT -p tcp -m tcp --dport 465 -j ACCEPT -A INPUT -j REJECT --reject-with icmp-host-prohibited -A FORWARD -j REJECT --reject-with icmp-host-prohibited -A OUTPUT -m state --state RELATED,ESTABLISHED -j ACCEPT -A OUTPUT -o lo -j ACCEPT -A OUTPUT -p tcp -m tcp --dport 8000 -j ACCEPT -A OUTPUT -p tcp -m tcp --dport 465 -j ACCEPT COMMIT # Completed on Sun Jun 1 13:20:20 2014 Are there any (obvious) issues with my iptables setup considering the above mentioned issues? Saying that the firewall is doing exactly nothing in this state is also an answer... And again, if you have any other suggestions for me to increase security (considering the basic things I do with this box), I would love hear it, also the obvious ones! Thanks!

  Read the article

• Legal IT documents

  - by TylerShads

  I have been wondering this past week because my big boss told me to start keeping track of all the things I have fixed, how to fix them, etc. Which is reasonable and have been doing anyway. But then a related question came to mind. What kind of documentation should I have on hand as far as users go. More specifically I am talking in terms of EULA, ToC, etc (correct me please if I'm using the wrong terms) Or more specifically a policy, so to speak, for the users and such. Can't say I'm a legal expert, otherwise I'd be a lawyer. The environment the users are in is pretty laid back so I don't forsee a problem. But assume that there should ever arise a problem, what should I have written up/have on hand? EDIT: I really should have noted that we are a medical transport facility and have patient records so I know that something must be done there to comply with HIPAA policies I believe. I do like what anthonysomerset said about the "If I get by a bus" Scenario and want to apply it not only to the documentation I am currently writing but also for if say an employee were to steal info from the server or edge cases, theft, etc. As far as our staff, its relatively small as in a single HR person, no legal department aside from the 2 owners' lawyers and me being the only IT person on staff with a guy who is no more than a mac superuser.

  Read the article

• I cannot access Windows Update at all

  - by Cardinal fang

  I have been unable to access the Windows update site for a couple of weeks now. I just get a message saying "Internet Explorer cannot display the webpage" and saying I have connection problems. Same thing is replicated with any other Microsoft site I try to access. The Automatic Updates also do not work. I can access every other wesbite I've surfed to. I've tried Googling the problem and based on what other site have suggested I have cleared my cache and temp files. I've scanning my hard drive with my antivirus in case I have a virus (nada). I've tried turning off my firewall and anti-virus (I run Zone Alarm). I've downloaded SpyBot and scanned my drive with that in case something was missed by Zone Alarm (again nada). Based on suggestions from the smart cookies on the Bad Science forum, I've used nslookup to check my translation isn't wonky (got all the info they said I should get). I've also tried navigating there directly using the IP address I was given (nope). I normally access the internet through a 3 mobile broadband connection, but have also tried connecting using a mate's wi-fi connection in case it was something on my mobile modem interferring. I run Windows XP SP3 with Internet Explorer 7 and Zone Alarm Internet Security Suite as my anti-virus/ firewall. Any suggestions?

  Read the article

• What should be monitored to troubleshoot file sharing problems?

  - by RyanW

  I'm running into some problems with a file share used by an ASP.NET web application. With this configuration, there are 2 web servers (win2k8 web) that connect to a file server (win2k8 enterprise), reading and writing files using a file share. Recently, one of the web servers has begun encountering an error accessing the file share: IOException: The specified network name is no longer available. There does not appear to be much info on the web for explaining what's causing this and how to best fix it, so I'm looking at what I can monitor in order to get clues. I'm not sure if it's hardware, just a load issue, file size, frequency, etc. With Windows perfmon, what can I monitor on the File Server side? There's the "Files Open" object, any other good ones? What can I monitor on the web server side? EDIT: I'll add that the UNC path uses the IP address of the file server, not a name to resolve. Also the share is a single, flat directory with over 100K files.

  Read the article

• PHP 5.3.2 Upgrade on Windows

  - by mcondiff

  I have a development box running Windows XP, Apache 2.2.15 Mysql and PHP 5.2.6 About a month ago I updated the Apache to the latest version and it went swimmingly. I am not having the same success with upgrading PHP to the latest version. I backed up my PHP directory and then deleted it. Used the Windows Installer for PHP 5.3.2, installed as an Apache 2.2.X module. I can get "Hello World" and phpinfo() to come up but cannot get mysql to connect. I have the extension un-commented in the php.ini and shouldn't really have to touch the Apache httpd.conf file since I didn't change the directory of PHP. Not sure what I'm doing wrong here. I have to get this right and then upgrade the Live Server too so I want to get this down pat. I've tried to use installation guides on the web with no luck. Any info pertaining to this problem would be great. I'm also afraid that the other PHP modules may not load but cannot really tell anything past mysql not working.

  Read the article

• Dell Latitude D510 Runs From Battery But Not AC Adapter

  - by Jason George

  I have a Dell Latitude D510 that went belly up around two years ago. It will run from the battery, however, the wall adapter will neither power the machine nor charge the battery. Once the battery is dead, the machine is dead. Since it died I've searched repeatedly for solutions. I've tried a new AC adapter and even removed and replaced the DC jack thinking one of the solder joints might be bad. Both to no avail. After two years of searching I finally found the answer today. Since it's such a simple fix and I had such a hard time finding it I wanted to post the info for others (as it is apparently a common issue with the D510). -----SOLUTION----- It seems this is commonly caused by a cracked solder joint at pin 1 on an inductor filter pair (FL2) near the power jack. Pins 1 and 4 are ground and pins 2 and 3 are power. There should be 20V from 1 to 2 and 3. Anything less indicates a cracked joint that is increasing resistance and dropping the supply voltage. Repair simply requires reflowing all four pins with a little added solder for security. Detailed instructions can be found here. Dell Latitude D510 solder problem

  Read the article

• AFP/SSH stopped working on OS X Server

  - by churnd

  I have 3 Mac OS X servers all bound to AD, all configured in the Golden Triangle setup. All 3 are completely separate from each other in terms of services, but all reside on the same internal network and are all bound to the same Active Directory domain. Two are 10.5.x (latest updates) and one is 10.6.3. Last weekend, all 3 simultaneously stopped allowing Active Directory users access to certain services, specifically AFP & SSH. SMB still works fine on all 3. I asked the AD admin if anything changed, and he said "Yes, we made a change to user accounts to toughen up security", and suggested I use [email protected] instead of just username. This still didn't work. I have completely removed one of my servers from AD, and re-joined, but this didn't work either. I can do kinit from command line and get a Kerberos ticket. sudo klist -ke shows all services are configured to use the correct Kerberos principles. I have been scavenging the logs for any useful info. The AFP log just shows that I'm connecting and disconnecting. The DirectoryService.log shows stuff about misconfigured Kerberos hashes, but my research is showing that's not uncommon. /var/log/system.log isn't showing anything useful that I can see. I'm not sure where to go from here. Any help/ideas appreciated.

  Read the article

• Green flickering pixels that move with black images

  - by user568458

  Strange question... Occasionally, on my LCD screen, pixels that should be black flicker rapidly and constantly between black and green, about 4 flickers a second. The crazy part is, unlike dead/stuck pixels, they are relative to content on the screen and move with it. For example, I might be looking at a web page with a picture that has lots of black. There might be a couple of green flashing pixels in that black that shouldn't be there. I scroll the page, and the green flickering pixels move with the image. It seems that everyphysical pixel is fine, but somehow something interprets part of the image in a way that causes flickering green... It's not just in a web browser. My first thought was to blame a trolling blogger cunningly uploading an animated gif that simulates a failing pixel... but it happens in a wide range of applications. It seems to occur randomly, other than that it seems to only occur in areas of pure black, and it's always pure 100% green. It happens rarely enough that it's not a big deal, but it's such a strange problem it bugs me. I can't find any info on anything like this. I'm not even sure if it's hardware or software. Any ideas? (windows 7 laptop connected to LCD by DVI to HDMI cable)

  Read the article

• Very high-pitched noise when computer does something intense?

  - by Starkers

  "Intense" is the best word I can use to describe it because I'm not sure what it is, whether it's RAM, GPU or CPU. If I pan the camera in unity: A high pitched noise issues from the computer. The picosecond I start panning the sound starts. Stops the picosecond I stop panning. If I start an infinite loop: 2.0.0p247 :016 > x = 1 => 1 2.0.0p247 :017 > while x < 2 do 2.0.0p247 :018 > puts 'huzzah!' 2.0.0p247 :019?> end huzzah! huzzah! huzzah! An identical high pitched noise can be heard. I don't think it's the GPU due to this simple experiment. Or any monitor-weirdness (although the sound does sound like one of those old CRT monitors if you're old enough to be young when those things were about) The CPU? Or maybe my SSD? It's my first SSD and the first time I've heard this noise. Should I be worried? Regardless, what's causing this sound? I can't think what would cause such high frequency vibrations. I built the PC myself. Not enough heat paste on the CPU? Too much? Just no idea what's going on. Info: CPU Type QuadCore Intel Core i5-3570K, 3800 MHz (38 x 100) Motherboard Name Asus Maximus V Extreme Flash Memory Type Samsung 21nm TLC NAND Video Adapter Asus HD7770

  Read the article

• How to enable hotlink protection without hardcoding my domain in the Apache config file?

  - by Jeff

  Been surfing around for a solution for a couple days now. How do I enable Apache hotlink protection without hardcoding my domain in the config file so I can port the code to my other domains without having to update the config file every time? This is what I have so far: RewriteCond %{HTTP_REFERER} !^$ RewriteCond %{HTTP_REFERER} !^http://www\.example\.com [NC] RewriteRule \.(gif|ico|jpe|jpeg|jpg|png)$ - [NC,F,L] ... And this is what Apache suggests: SetEnvIf Referer example\.com localreferer <FilesMatch \.(jpg|png|gif)$> Order deny,allow Deny from all Allow from env=localreferer </FilesMatch> ... both of which hardcode the domain in their rules. The closest I came to finding any info that covers this is right here on ServerFault, but the conclusion was that it cannot be done. Based on my research, that appears to be true, but I didn't find any questions or commentary dedicated soley to this question. If anyone's curious, here is the link to the Apache 2 docs that cover this topic. Note that Apache variables (e.g. %{HTTP_REFERER}) can only be used in the RewriteCond text-string and the RewriteRule substitution arguments.

  Read the article

• This .mpg video clip doesn't play well

  - by Roey

  I've installed K-lite mega codec pack v6.9.0 with playback essentials without player. My default and only media player is windows media player. here are the clip's media info: General Complete name : D:\Users\Roey\Downloads\B384MV.mpg Format : MPEG-PS File size : 273 MiB Duration : 4mn 59s Overall bit rate : 7 643 Kbps Video ID : 224 (0xE0) Format : MPEG Video Format version : Version 2 Format profile : Main@High Format settings, BVOP : No Format settings, Matrix : Default Format settings, GOP : M=1, N=15 Duration : 4mn 57s Bit rate mode : Variable Bit rate : 7 363 Kbps Nominal bit rate : 9 000 Kbps Width : 1 920 pixels Height : 1 080 pixels Display aspect ratio : 16:9 Frame rate : 25.000 fps Color space : YUV Chroma subsampling : 4:2:0 Bit depth : 8 bits Scan type : Progressive Compression mode : Lossy Bits/(Pixel*Frame) : 0.142 Stream size : 261 MiB (96%) Audio ID : 192 (0xC0) Format : MPEG Audio Format version : Version 1 Format profile : Layer 3 Mode : Joint stereo Duration : 4mn 59s Bit rate mode : Constant Bit rate : 128 Kbps Channel(s) : 2 channels Sampling rate : 44.1 KHz Compression mode : Lossy Stream size : 4.56 MiB (2%) Menu When I play it there is no sound (just a little "kahhhh" noise every 10-20 seconds) and the frames are moving very slow - it "jumps" frames. A blue tray icon [FFa] "ffdshow audio decoder" pops with the following details: Input:MP3, stereo, 44100 Hz (libavocodec) Output:PCM, stereo, 44100 Hz, 16-bit integer Any help will be much appreciated. Thanks

  Read the article

• Why does Internet Explorer sometimes fail to connect to anything until I restart it?

  - by cletus

  IE has an annoying problem on my PC (XP SP3). I start it and try to go to Google (for example) and it'll sit there saying "Connecting" but nothing will happen and it doesn't matter how many times I try, it won't connect to anything. I discovered that if I kill IE and restart it then it might start working (and then it'll work every time). It might takes 3-4 restarts (of IE, not the PC) to get a working IE. Now I wouldn't normally care about this since I use Chrome but a lot of things use IE by default like Windows Update and the online help in Office 2003 so I would like to fix it. Interestingly, my work laptop, which is running Windows 7 RC 64-bit, has exactly the same problem (completely different network and everything). I'm utterly convinced it's not a network or hardware problem but some software problem. Edit: More info. It's IE8; No add-ons; Automatically detect settings is not enabled. It is set to "Never dial a connection".

  Read the article

• Running $ORIGIN linked binaries from setuid scripts on linux

  - by drscroogemcduck

  I'm using suidperl to run some programs that require root permissions. however, the runtime linker won't expand library paths which contain $ORIGIN entries so the programs i want to run (jstack from java) won't run. more info here There is one exception to the advice to make heavy use of $ORIGIN. The runtime linker will not expand tokens like $ORIGIN for secure (setuid) applications. This should not be a problem in the vast majority of cases. my program looks something like this: #!/usr/bin/perl $ENV{PATH} = "/usr/local/sbin:/usr/local/bin:/sbin:/bin:/usr/sbin:/usr/bin:/usr/java/jdk1.6.0_12/bin:/root/bin"; $ENV{JAVA_HOME} = "/usr/java/jdk1.6.0_12"; open(FILE, '/var/run/kil.pid'); $pid = <FILE>; close(FILE); chomp($pid); if ($pid =~ /^(\d+)/) { $pid = $1; } else { die 'nopid'; } system( "/usr/java/jdk1.6.0_12/bin/jstack", "$pid"); is there any way to fork off a child process in a way so that the linker will work correctly.

  Read the article

• HP DL185 - very slow disk read speed

  - by fistameeny

  Hi, I have a HP DL185 G6 Server (12 disk model) with the following spec: Quad Core Xeon 2.27GHz 6GB RAM HP P212 RAID controller with battery backup 2 x 128GB 15K SAS 3.5" (RAID-1 for the operating system) 4 x 750GB 7.5K SAS 3.5" (RAID-5 for the data, 2TB usable space) The operating system is Ubuntu Server 9.10. Both drives have been formatted as EXT4. We are finding that read speed of the RAID-5 array is poor. Disk test results below: sudo hdparm -tT /dev/cciss/c0d1p1 /dev/cciss/c0d1p1: Timing cached reads: 15284 MB in 2.00 seconds = 7650.18 MB/sec Timing buffered disk reads: 74 MB in 3.02 seconds = 24.53 MB/sec For info, the RAID-1 array performs as follows: sudo hdparm -tT /dev/cciss/c0d0p1 /dev/cciss/c0d0p1: Timing cached reads: 15652 MB in 2.00 seconds = 7834.26 MB/sec Timing buffered disk reads: 492 MB in 3.01 seconds = 163.46 MB/sec We thought this was because with no battery, read/write cache is disabled. We have bought and installed the battery backup and have used the HP bootable CD to change the cache settings to 50% read / 50% write and check cache is enabled on the drives and the controller. Is there something I'm missing?

  Read the article

• What can cause kernel out_of_memory error?

  - by nbolton

  I'm running Debian GNU/Linux 5.0 and I'm experiencing intermittent out_of_memory errors coming from the kernel. The server stops responding to all but pings, and I have to reboot the server. # uname -a Linux xxx 2.6.18-164.9.1.el5xen #1 SMP Tue Dec 15 21:31:37 EST 2009 x86_64 GNU/Linux This seems to be the important bit from /var/log/messages Dec 28 20:16:25 slarti kernel: Call Trace: Dec 28 20:16:25 slarti kernel: [<ffffffff802bedff>] out_of_memory+0x8b/0x203 Dec 28 20:16:25 slarti kernel: [<ffffffff8020f825>] __alloc_pages+0x245/0x2ce Dec 28 20:16:25 slarti kernel: [<ffffffff8021377f>] __do_page_cache_readahead+0xc6/0x1ab Dec 28 20:16:25 slarti kernel: [<ffffffff80214015>] filemap_nopage+0x14c/0x360 Dec 28 20:16:25 slarti kernel: [<ffffffff80208ebc>] __handle_mm_fault+0x443/0x1337 Dec 28 20:16:25 slarti kernel: [<ffffffff8026766a>] do_page_fault+0xf7b/0x12e0 Dec 28 20:16:25 slarti kernel: [<ffffffff8026ef17>] monotonic_clock+0x35/0x7b Dec 28 20:16:25 slarti kernel: [<ffffffff80262da3>] thread_return+0x6c/0x113 Dec 28 20:16:25 slarti kernel: [<ffffffff8021afef>] remove_vma+0x4c/0x53 Dec 28 20:16:25 slarti kernel: [<ffffffff80264901>] _spin_lock_irqsave+0x9/0x14 Dec 28 20:16:25 slarti kernel: [<ffffffff8026082b>] error_exit+0x0/0x6e Full snippet here: http://pastebin.com/a7eWf7VZ I thought that perhaps the server was actually running out of memory (it has 1GB physical memory), but my Cacti memory graph looks OK to me... But strangely the load graph goes through the roof shortly before the kernel crashes: What logs can I look at for more info? Update: Maybe noteworthy - the CPU percentage and network traffic graphs were both normal at the time of the crash. The only abnormality was the average load graph.

  Read the article

• Games, Windows 8.1 and 144Hz display

  - by Marioysikax

  So I have been having problems with few games after switching from 7 to 8.1, which seems to be related to my 144Hz monitor. Few examples: Shank, Shank 2, Blood of the Werewolf, Astebreed, the Sims 2 and Rayman Legends patch 1.2Had few other as well but it's been long and I have 600+ steam library. From those games at least the Sims 2 and Shank worked without any problems with same setup and Windows 7. So basically these games simply refuse to launch with basic setup. However if I plug 60Hz TV with HDMI instead everything magically starts to work. As for Astebreed and the Sims 2 using windowed mode seems to also work. As for Rayman Demo and version 1.0 works for some reason and 1.2 breaks settings menu. I have already tried contacting supports. EA support stated game simply shouldn't work with 8.1 at all (which is lie as it works with that TV and friend with 8 plays just fine), ubisoft support took few weeks and support said he will forward info for further processing, blood of the werewolf support had no idea what's going on and told me to just use my TV instead.Changing monitors refresh rate to 120Hz or forcing it to 60Hz doesn't do anything. I have DVI right now but I will try with DisplayPort when I get the cable. At PCGW Garrett said it may have something to do how listing resolutions work with 8 compared to earlier Windows versions but my googling skills don't bring anything up and compatibility mode for earlier windows version doesn't work either (not that I expected that to work). My system specs are on my steam profile. How do I get those work with my 144Hz monitor as well as possible future games having same problem? Downgrading to 7 would work but is far from practical and I don't own legit lisence for that one.

  Read the article

• AMD Phenom II X2 555 BE, core unlock suddenly not working?

  - by user328271

  I've had a Phenom II X2 555 BE for around 2 - 3 years. When I got it, I immediately core unlocked it with my ECS A880GM-A3 mobo, which makes it turn into a Phenom II X4 B55. A few days ago, I installed Windows 7 64 bit to compensate for my 4 gigs of ram. When I start my system with its cores unlocked, it will restart after the BIOS screen. If I disable the core unlock, it boots to OS just fine. My question is: Does 64 bit OS makes a difference in core unlocking? Does my 3rd and 4th core burnt out? Also extra info: I tried core unlocking but keeping the 3rd and 4th core disabled and it still won't boot into OS. Could it be motherboard problems? Sorry for bad English. I will try to give additional information if needed. Thanks! Also it is worth mentioning I'm no computer expert but I tried to make my explanation as short as possible. I also asked my question on TomsHardware, but I had no answer till now so I decided to ask here too. anyone...?

  Read the article

• Nagios send mail when server is down

  - by tzulberti

  I am using nagios 3.06 to monitor the servers. When a service is critical, it sends a mail, but when a server is down no mail is sent. Even if all the services go to critical state, no mail is sent. I have the following configuration: define command {     command_name notify-host-by-email     command_line python /etc/nagios3/send_mail.py "[Nagios] $HOSTNAME$" "******** Nagios ****\n\n Host: $HOSTNAME$\n Description: the server is down" } define command{     command_name notify-service-by-email     command_line python /etc/nagios3/send_mail.py "[Nagios] $HOSTNAME$: $SERVICEDESC$ ($NOTIFICATIONTYPE$)" "***** Nagios *****\n\nNotification Type: $NOTIFICATIONTYPE$\nService: $SERVICEDESC$\nHost: $HOSTALIAS$\nAddress: $HOSTADDRESS$\nState: $SERVICESTATE$\nDate/Time: $LONGDATETIME$\nAdditional Info:$SERVICEOUTPUT$" } The python script is a script to sent a mail. It works if I execute it from the command line, but it doesn't sents an email from nagios. What I am doing wrong? UPDATE: The contact data is: define contact{     contact_name root     alias Root     service_notification_period 24x7     host_notification_period 24x7     service_notification_options w,u,c,r     host_notification_options d,r     service_notification_commands notify-service-by-email     host_notification_commands notify-host-by-email     email [email protected] } define contactgroup{     contactgroup_name admins     alias Nagios Administrators     members root }

  Read the article

< Previous Page | 551 552 553 554 555 556 557 558 559 560 561 562  | Next Page >