Search Results

Search found 15558 results on 623 pages for 'basic authentication'.

Page 559/623 | < Previous Page | 555 556 557 558 559 560 561 562 563 564 565 566  | Next Page >

• hostapd running on Ubuntu Server 13.04 only allows single station to connect when using wpa

  - by user450688

  Problem Only a single station can connect to hostapd at a time. Any single station can connect (W8, OSX, iOS, Nexus) but when two or more hosts are connected at the same time the first client loses its connectivity. However there are no connectivity issues when WPA is not used. Setup Linux (Ubuntu server 13.04) wireless router (with separate networks for wired WAN, wired LAN, and Wireless LAN. iptables-save output: *nat :PREROUTING ACCEPT [0:0] :INPUT ACCEPT [0:0] :OUTPUT ACCEPT [0:0] :POSTROUTING ACCEPT [0:0] -A POSTROUTING -s 10.0.0.0/24 -o p4p1 -j MASQUERADE -A POSTROUTING -s 10.0.1.0/24 -o p4p1 -j MASQUERADE COMMIT *mangle :PREROUTING ACCEPT [13:916] :INPUT ACCEPT [9:708] :FORWARD ACCEPT [4:208] :OUTPUT ACCEPT [9:3492] :POSTROUTING ACCEPT [13:3700] COMMIT *filter :INPUT DROP [0:0] :FORWARD DROP [0:0] :OUTPUT ACCEPT [9:3492] -A INPUT -i p4p1 -m state --state RELATED,ESTABLISHED -j ACCEPT -A INPUT -i p4p1 -p tcp -m tcp --dport 22 -m state --state NEW -j ACCEPT -A INPUT -i eth0 -j ACCEPT -A INPUT -i wlan0 -j ACCEPT -A INPUT -i lo -j ACCEPT -A FORWARD -i p4p1 -m state --state RELATED,ESTABLISHED -j ACCEPT -A FORWARD -i eth0 -j ACCEPT -A FORWARD -i wlan0 -j ACCEPT -A FORWARD -i lo -j ACCEPT COMMIT /etc/hostapd/hostapd.conf #Wireless Interface interface=wlan0 driver=nl80211 ssid=<removed> hw_mode=g channel=6 max_num_sta=15 auth_algs=3 ieee80211n=1 wmm_enabled=1 wme_enabled=1 #Configure Hardware Capabilities of Interface ht_capab=[HT40+][SMPS-STATIC][GF][SHORT-GI-20][SHORT-GI-40][RX-STBC12] #Accept all MAC address macaddr_acl=0 #Shared Key Authentication wpa=1 wpa_passphrase=<removed> wpa_key_mgmt=WPA-PSK wpa_pairwise=CCMP rsn_pairwise=CCMP ###IPad Connectivevity Repair ieee8021x=0 eap_server=0 Wireless Card #lshw output product: RT2790 Wireless 802.11n 1T/2R PCIe vendor: Ralink corp. physical id: 0 bus info: pci@0000:03:00.0 logical name: mon.wlan0 version: 00 serial: <removed> width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list logical wireless ethernet physical configuration: broadcast=yes driver=rt2800pci driverversion=3.8.0-25-generic firmware=0.34 ip=10.0.1.254 latency=0 link=yes multicast=yes wireless=IEEE 802.11bgn #iw list output Band 1: Capabilities: 0x272 HT20/HT40 Static SM Power Save RX Greenfield RX HT20 SGI RX HT40 SGI RX STBC 2-streams Max AMSDU length: 3839 bytes No DSSS/CCK HT40 Maximum RX AMPDU length 65535 bytes (exponent: 0x003) Minimum RX AMPDU time spacing: 2 usec (0x04) HT RX MCS rate indexes supported: 0-15, 32 TX unequal modulation not supported HT TX Max spatial streams: 1 HT TX MCS rate indexes supported may differ Frequencies: * 2412 MHz [1] (27.0 dBm) * 2417 MHz [2] (27.0 dBm) * 2422 MHz [3] (27.0 dBm) * 2427 MHz [4] (27.0 dBm) * 2432 MHz [5] (27.0 dBm) * 2437 MHz [6] (27.0 dBm) * 2442 MHz [7] (27.0 dBm) * 2447 MHz [8] (27.0 dBm) * 2452 MHz [9] (27.0 dBm) * 2457 MHz [10] (27.0 dBm) * 2462 MHz [11] (27.0 dBm) * 2467 MHz [12] (disabled) * 2472 MHz [13] (disabled) * 2484 MHz [14] (disabled) Bitrates (non-HT): * 1.0 Mbps * 2.0 Mbps (short preamble supported) * 5.5 Mbps (short preamble supported) * 11.0 Mbps (short preamble supported) * 6.0 Mbps * 9.0 Mbps * 12.0 Mbps * 18.0 Mbps * 24.0 Mbps * 36.0 Mbps * 48.0 Mbps * 54.0 Mbps max # scan SSIDs: 4 max scan IEs length: 2257 bytes Coverage class: 0 (up to 0m) Supported Ciphers: * WEP40 (00-0f-ac:1) * WEP104 (00-0f-ac:5) * TKIP (00-0f-ac:2) * CCMP (00-0f-ac:4) Available Antennas: TX 0 RX 0 Supported interface modes: * IBSS * managed * AP * AP/VLAN * WDS * monitor * mesh point software interface modes (can always be added): * AP/VLAN * monitor valid interface combinations: * #{ AP } <= 8, total <= 8, #channels <= 1 Supported commands: * new_interface * set_interface * new_key * new_beacon * new_station * new_mpath * set_mesh_params * set_bss * authenticate * associate * deauthenticate * disassociate * join_ibss * join_mesh * set_tx_bitrate_mask * set_tx_bitrate_mask * action * frame_wait_cancel * set_wiphy_netns * set_channel * set_wds_peer * Unknown command (84) * Unknown command (87) * Unknown command (85) * Unknown command (89) * Unknown command (92) * testmode * connect * disconnect Supported TX frame types: * IBSS: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 * managed: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 * AP: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 * AP/VLAN: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 * mesh point: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 * P2P-client: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 * P2P-GO: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 * Unknown mode (10): 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 Supported RX frame types: * IBSS: 0x40 0xb0 0xc0 0xd0 * managed: 0x40 0xd0 * AP: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0 * AP/VLAN: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0 * mesh point: 0xb0 0xc0 0xd0 * P2P-client: 0x40 0xd0 * P2P-GO: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0 * Unknown mode (10): 0x40 0xd0 Device supports RSN-IBSS. HT Capability overrides: * MCS: ff ff ff ff ff ff ff ff ff ff * maximum A-MSDU length * supported channel width * short GI for 40 MHz * max A-MPDU length exponent * min MPDU start spacing Device supports TX status socket option. Device supports HT-IBSS.

  Read the article

• Why does Ubuntu 9.10 hang during boot at "Booting processor 1 APIC 0x1 ip 0x6000"?

  - by BraeburnDev

  I recently installed a new copy of Ubuntu 9.10 (Kernel 2.6.31-14) on to my Hp Pavilion dv6t, so I can setup a Linux development environment. The install went flawlessly and I proceeded with Ubuntu's udate manager's long list of updates (292 in all). I also setup a swap file and activated a Nvidia 185 driver for the Nvidia 260m GPU on the machine. After all this was done I restarted the computer and booted into Ubuntu this time with a newer 2.6.31-19 Kernel which was installed from the update manager. During booth the computer hung at this point: Feb 24 14:23:12 braeburn-laptop kernel: [ 0.013136] Performance Counters: Nehalem/Corei7 events, Intel PMU driver. Feb 24 14:23:12 braeburn-laptop kernel: [ 0.013141] ... version: 3 Feb 24 14:23:12 braeburn-laptop kernel: [ 0.013142] ... bit width: 48 Feb 24 14:23:12 braeburn-laptop kernel: [ 0.013144] ... generic counters: 4 Feb 24 14:23:12 braeburn-laptop kernel: [ 0.013146] ... value mask: 0000ffffffffffff Feb 24 14:23:12 braeburn-laptop kernel: [ 0.013147] ... max period: 000000007fffffff Feb 24 14:23:12 braeburn-laptop kernel: [ 0.013149] ... fixed-purpose counters: 3 Feb 24 14:23:12 braeburn-laptop kernel: [ 0.013151] ... counter mask: 000000070000000f Feb 24 14:23:12 braeburn-laptop kernel: [ 0.015539] ACPI: Core revision 20090521 Feb 24 14:23:12 braeburn-laptop kernel: [ 0.052264] Setting APIC routing to flat Feb 24 14:23:12 braeburn-laptop kernel: [ 0.052639] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1 Feb 24 14:23:12 braeburn-laptop kernel: [ 0.152580] CPU0: Intel(R) Core(TM) i7 CPU Q 720 @ 1.60GHz stepping 05 Feb 24 14:23:12 braeburn-laptop kernel: [ 0.270845] Booting processor 1 APIC 0x1 ip 0x6000 I can post a full kern.log of this boot process if requested. Hopefully this is enough information to go on. I should add that I'm still new to configuring and running a Linux OS although I know enough basic command line usage to do software development. This is my attempt to become more familiar with Linux and manage my own system. I'd like to get some insight on the nature of this system hang, what the problem is and how to resolve it. At this point I can scrap the install if I broke something, but my intuition says this is an issue with the kernel recognizing the correct hardware configuration for my system, or perhaps this is an issue with the APIC drivers managing Nehalem's new power management capabilities? Thanks for looking at this issue and providing feed back.

  Read the article

• Trouble with Debian Lenny and Sphinx

  - by Ando

  I've very basic understanding of linux systems, but I've a server which was setup a while ago to host some web apps. Recently I decided to test out and implement Sphinx but unfortunately I cant get the install to work. I'm running a Debian Lenny distro and when I try to install sphinx it says - checking MySQL include files... configure: error: missing include files. ****************************************************************************** ERROR: cannot find MySQL include files. Check that you do have MySQL include files installed. The package name is typically 'mysql-devel'. If include files are installed on your system, but you are still getting this message, you should do one of the following: 1) either specify includes location explicitly, using --with-mysql-includes; 2) or specify MySQL installation root location explicitly, using --with-mysql; 3) or make sure that the path to 'mysql_config' program is listed in your PATH environment variable. To disable MySQL support, use --without-mysql option. ****************************************************************************** I do have mysql 5.1 installed but I can't find the include files, AND one more thing.. I read around the net that I probably need libmysqlclient15-dev but when I try to install that using apt-get i receive the following error. The following packages were automatically installed and are no longer required: libxcb-aux0 libts-0.0-0 libxcb-atom1 ttf-dejavu-extra hunspell-en-us g++-4.3 libmysql++3 libnspr4-0d libdirectfb-1.0-0 libxcb-event1 libasound2 libstdc++6-4.3-dev libhunspell-1.2-0 ttf-dejavu libmozjs2d conkeror-spawn-process-helper libnss3-1d Use 'apt-get autoremove' to remove them. The following NEW packages will be installed: libmysqlclient15-dev 0 upgraded, 1 newly installed, 0 to remove and 276 not upgraded. Need to get 7590 kB of archives. After this operation, 26.3 MB of additional disk space will be used. WARNING: The following packages cannot be authenticated! libmysqlclient15-dev Install these packages without verification [y/N]? Y Err http://ftp.us.debian.org/debian/ lenny/main libmysqlclient15-dev amd64 5.0.51a-24+lenny5 404 Not Found [IP: 35.9.37.225 80] Err http://security.debian.org/ lenny/updates/main libmysqlclient15-dev amd64 5.0.51a-24+lenny5 404 Not Found [IP: 149.20.20.6 80] Failed to fetch http://security.debian.org/pool/updates/main/m/mysql-dfsg-5.0/libmysqlclient15-dev_5.0.51a-24+lenny5_amd64.deb 404 Not Found [IP: 149.20.20.6 80] E: Unable to fetch some archives, maybe run apt-get update or try with --fix-missing? Can you help me out by suggesting how to install the required packages and run the Sphinx.

  Read the article

• configuring slime in emacs

  - by CodeKingPlusPlus

  I am in the process of configuring slime for emacs. So far I have read about basic functionality for common lisp such as C-c C-q which invokes the command slime-close-parens-at-point which places the proper number of parens where your mouse is. Another command that seemed cool was invoked by C-c C-c and it would pass the code you are editing in a buffer to the REPL, and "compile" it. Why won't these commands work for me? Anyway, I have downloaded slime via M-x list-packages and do not seem to have this functionality (C-h w and then any of these commands tells me that these commands do note exist). So, I saw a bunch of other slime extensions such as slime-repl', 'slime-fuzzy' and 'hippie-expand-slime'. So I again usedM-x list-packages` and downloaded them. Still I did not have these commands. Here is the content of my emacs file relevant to slime: ;;;Common Lisp and Slime (add-to-list 'load-path "/home/s2s2/.emacs.d/elpa/slime-20130626.1151") (add-to-list 'load-path "/home/s2s2/.emacs.d/elpa/slime-repl-201000404") (add-to-list 'load-path "/home/s2s2/.emacs.d/elpa/hippie-expand-slime-20130226.1656") (add-to-list 'load-path "/home/s2s2/.emacs.d/elpa/slime-fuzzy-20100404") (require 'slime) (setq slime-lisp-implementations `((sbcl ("/usr/bin/sbcl")) (ecl ("/usr/bin/ecl")) (clisp ("/usr/bin/clisp" "-q -I")))) (require 'slime-repl) (require 'slime-fuzzy) (require 'hippie-expand-slime) When I execute M-x slime I get the following message in the inferior-lisp buffer where I can execute common lisp code (however, shouldn't this be the slime-repl since I required it?): STYLE-WARNING: redefining EMACS-INSPECT (#<BUILT-IN-CLASS T>) in DEFMETHOD STYLE-WARNING: Implicitly creating new generic function STREAM-READ-CHAR-WILL-HANG-P. WARNING: These Swank interfaces are unimplemented: (DISASSEMBLE-FRAME SLDB-BREAK-AT-START SLDB-BREAK-ON-RETURN) ;; Swank started at port: 46533. Then a slime-error buffer is created with the contents: Invalid protocol message: Symbol "CREATE-REPL" not found in the SWANK package. Line: 1, Column: 28, File-Position: 28 Stream: #<SB-IMPL::STRING-INPUT-STREAM {10056B9C33}> (:emacs-rex (swank:create-repl nil) "COMMON-LISP-USER" t 5) How should I modify my emacs file to give me the functionality of those commands? In my emacs file am I not loading the necessary files? Do I need to install an additional package? If you need more information let me know! All help is much appreciated!

  Read the article

• Could I centralize batch files more efficiently?

  - by PeanutsMonkey

  I am new to the world of batch scripting so please forgive what may appear as basic questions. I am learning as I get assigned different jobs and I am a huge proponent of automation where possible. I have several batch files that perform several tasks. Each of these files had their paths hard-coded e.g. c:\temp. d:\data, etc in the batch file. Initially I moved these to a text file I could call from a batch file e.g. for /f "tokens=1,2 delims==" %%R in (config.txt) do ( if %%R==bdata set bdata=%%S if %%R==cdata set cdata=%%S ) The config.txt file contains these values bdata=c:\temp cdata=d:\data I realized that each time I would need to create a new variable, I would need to update the config.txt file as well the config.bat files. I decided I would move all the values to just the config.bat file as follows set bdata=c:\temp set cdata=d:\data I then updated each of the existing batch files to call the variables rather than the hard-coded paths. I also added the following lines of code to each batch file except config.bat. The only additional line added to the config.bat file is @echo off. @echo off setlocal enableextensions enabledelayedexpansion call config.bat I then have another batch file that centralizes calling all the batch files in sequence. The name of this batch file is start.bat. The reason I am using start /wait is because there have been instances of where the delete.bat runs before compress.bat has had an opportunity to finish. start /wait compress.bat start /wait validate.bat start /wait delete.bat Questions Is this the best way to centralize values and if not, what is a better way? Do I need to specify setlocal enableextensions enabledelayedexpansion in all the existing batch files? Do all the batch files have to have @echo off or is it sufficient for just the config.bat file? Is start /wait the best way to call multiple files? Can I pass values from one batch file to another using the said command? All the batch files have different functions e.g. move, delete, etc however use %%a or %%b. Is this okay? For example The validate.bat file has the code for %%a in (%bdata%\*.*) do if "%%~xa" == "" move /Y "%bdata%\%%~xa" "%bdata%\%done%" and the delete.bat file has the code for %%a in (%bdata%\*.*) do if "%%~xa" == ".txt" del "%%a"

  Read the article

• Yahoo is sending our server's transactional email to the Spam folder, even though we have set up SPF and DKIM

  - by Derrick Miller

  Yahoo Mail is sending our server's transactional emails to the Spam folder, even though we have taken quite a few anti-spam steps. By contrast, Gmail allows the messages through to the inbox just fine. Here are the things which are in place: SPF is set up for the domain holsteinplaza.com. Yahoo reports spf=pass in the message headers. DKIM is set up for the domain holsteinplaza.com. Yahoo reports dkim=pass in the message headers. We have a proper reverse DNS entry for the sending mail server. Name - IP matches IP - Name. Neither Domainkeys nor SenderID are set up. From what I can tell, DKIM is the way of the future, and there is not much to be gained from adding Domainkeys or SenderID. Following are the headers. Any ideas what more I should do to get Yahoo to stop flagging the emails as spam? From Holstein Plaza Auctions Sat Jun 25 18:30:08 2011 X-Apparently-To: [email protected] via 98.138.90.132; Sat, 25 Jun 2011 18:30:11 -0700 Return-Path: <[email protected]> X-YahooFilteredBulk: 70.32.113.42 Received-SPF: pass (domain of holsteinplaza.com designates 70.32.113.42 as permitted sender) X-YMailISG: i_vaA_QWLDuLOmXhDjUv3aBKJl5Un6EiP6Yk2m4yn3jeEuYK MkhpqIt9zDUbHARCwXrhl9pqjTANurGVca7gytSs.mryWVQcbWBx.DaItWRb VcyrIzwMzXKCSeu06H2a.cJ7HG5vJLJaKmHUUI_1ttXKn_Aegiu5yHvFX83R Lpth0witO9zfaKvOMaJV3LAxpIpFOydwvq1cqjZ8nURxQbxM3Cl.QW7MxxrC 09qLVn_D_xSdU94QdU22IsVmlaRHv.uU5dnIazu.KSkhKpYykDoZA2SH0SY4 JmTZj3LP8N926xXVDzYQ5K6QvKuJL5g0d9pYZx3KC59sgIu5oHlJ3Q15RdKb f3OJw0PR6oIyJ2yStVr8vfbDgOfj3qig03.Tw6g6MMNpv1G7Cuol4oJeUaYP xELxX6dHgBgCSuWMcbsrxbK4BIXcS2qhpMqYQ4Isk.XXyA8uvmFXyvgc1ds5 8jo0rW.Wsw.55Z.KTPaQ0gHXj0T3OGppYMELSJv1iuhPyyAnZpmq01CU0Qd5 CcRgdyW3HaqhmpXqJCS0Clo16zXA4HmAjR0tgIQrHRLc3D9N02AOzvmDgCb1 vCh0p00QeKVq8UNkcShPRxZFKi9khtkLhPBlXEKkhJ76zyDmHUxTY.dQHVVD 8D2hx7BxbqI9DINI8x5oR5Q8hYkZqHYQsmGNkaU77O2BnsEv5WxMEmzrBJ4Z h8zGCidgYPiZycZfnfaBp0Xb4tya2WMTN45W02JFcO1qq_UMJ9xPeqZhPEj. j9YvBAC8324GGF.c8eWcNB2VB34QHgTcVUl3.c0XUCuncls9Cyg4L7AoIdCi HvAklSzDDu9nW6732VEipV9FJ_JkDupDNQU2hfiPG.3OeF8GwTnVYnEn0EiZ aO0NCnZhXuLDcN3K7ml3846yRdASvzPFs9s4aJkzR0FkhVvptiMBEOdRkKdG wHWmvWpK4GTZpW4yU7CnKpW2MiWWn1MP0h_CCZFKs5.3mfmfPjPVIABN_RuU Q8ex5hdKnKlQiqK56LzcPRnYmNtrwdsUX9CYn9d6cPpXR_Bi5jrNJMNzdFvq lGO0CBT4QPe2V45U8PtpMitttuDA1cCvmyBPFswxNlL0jyX0a_W.vl0YW5.d HhDItpHhDxKRUscM28IR.exetq4QCzyM X-Originating-IP: [70.32.113.42] Authentication-Results: mta1267.mail.ac4.yahoo.com from=holsteinplaza.com; domainkeys=neutral (no sig); from=holsteinplaza.com; dkim=pass (ok) Received: from 127.0.0.1 (EHLO predator.axis80.com) (70.32.113.42) by mta1267.mail.ac4.yahoo.com with SMTP; Sat, 25 Jun 2011 18:30:11 -0700 Received: (qmail 1440 invoked by uid 48); 25 Jun 2011 21:30:09 -0400 To: [email protected] Subject: this is a test X-PHPMAILER-DKIM: phpmailer.worxware.com DKIM-Signature: v=1; a=rsa-sha1; q=dns/txt; l=203; s=auction; t=1309051808; c=relaxed/simple; h=From:To:Subject; d=holsteinplaza.com; [email protected]; z=From:=20Holstein=20Plaza=20Auctions=20<[email protected]> |To:[email protected] |Subject:=20this=20is=20a=20test; bh=B3Tw5AQb1va627KEoazuFEBZ0fg=; b=oQ5uFq+oekPTGhszyIritjuuIAi3qPNyeitu+aWMhdx3oC6O2j5hJsDFpK0sS5fms7QdnBkBcEzT0iekEvn9EfAdCkGZ2KrtEC0yv7QKQcrjXxy07GJpj9nq0LYbgOuPdw8mGvKxlRZ+jFBX0DRJm0xXFLkr+MEaILw7adHTCCM= Date: Sat, 25 Jun 2011 21:30:08 -0400 From: Holstein Plaza Auctions <[email protected]> Reply-to: Holstein Plaza Auctions <[email protected]> Message-ID: <[email protected]> X-Priority: 3 X-Mailer: PHPMailer 5.1 (phpmailer.sourceforge.net) MIME-Version: 1.0 Content-Transfer-Encoding: 8bit Content-Type: text/plain; charset="iso-8859-1" Content-Length: 195

  Read the article

• Mod_rewrite with UTF-8 accent, multiviews , .htaccess

  - by GuruJR

  Problem: with Mod_rewrite, multiview & Apache config Introduction: The website is in french and i had problem with unicode encoding and mod_rewrite within php wihtout multiviews Old server was not handling utf8 correctly (somewhere between PHP, apache mod rewrite or mysql) Updated Server to Ubuntu 11.04 , the process was destructive lost all files in var/www/ (the site was mainly 2 files index.php & static.php) lost the site specific .Htaccess file lost MySQL dbs lost old apache.conf What i have done so far: What works: Setup GNutls for SSL, Listen 443 = port.conf Created 2 Vhosts in one file for :80 and :443 = website.conf Enforce SSL = Redirecting :80 to :443 with a mod_rewrite redirect Tried to set utf-8 everywhere.. Set charset and collation , db connection , mb_settings , names utf-8 and utf8_unicode_ci, everywhere (php,mysql,apache) to be sure to serve files as UTF-8 i enabled multiview renamed index.php.utf8.fr and static.php.utf8.fr With multiview enabled, Multibytes Accents in URL works SSL TLS 1.0 What dont work: With multiview enabled , mod_rewrite works for only one of my rewriterules With multiview Disabled, i loose access to the document root as "Forbidden" With multiview Disabled, i loose Multibytes (single charater accent) The Apache Default server is full of settings. (what can i safely remove ?) these are my configuration files so far :80 Vhost file (this one work you can use this to force redirect to https) RewriteEngine On RewriteCond %{HTTPS} off RewriteRule (.*) https://%{HTTP_HOST}%{REQUEST_URI} LanguagePriority fr :443 Vhost file (GnuTls is working) DocumentRoot /var/www/x ServerName example.com ServerAlias www.example.com <Directory "/var/www/x"> allow from all Options FollowSymLinks +MultiViews AddLanguage fr .fr AddCharset UTF-8 .utf8 LanguagePriority fr </Directory> GnuTLSEnable on GnuTLSPriorities SECURE:+VERS-TLS1.1:+AES-256-CBC:+RSA:+SHA1:+COMP-NULL GnuTLSCertificateFile /path/to/certificate.crt GnuTLSKeyFile /path/to/certificate.key <Directory "/var/www/x/base"> </Directory> Basic .htaccess file AddDefaultCharset utf-8 Options FollowSymLinks +MultiViews RewriteEngine on RewriteRule ^api/$ /index.php.utf8.fr?v=4 [L,NC,R] RewriteRule ^contrib/$ /index.php.utf8.fr?v=2 [L,NC,R] RewriteRule ^coop/$ /index.php.utf8.fr?v=3 [L,NC,R] RewriteRule ^crowd/$ /index.php.utf8.fr?v=2 [L,NC,R] RewriteRule ^([^/]*)/([^/]*)$ /static.php.utf8.fr?VALUEONE=$2&VALUETWO=$1 [L] So my quesiton is whats wrong , what do i have missing is there extra settings that i need to kill from the apache default . in order to be sure all parts are using utf-8 at all time, and that my mod_rewrite rules work with accent Thank you all in advance for your help, I will follow this question closely , to add any needed information.

  Read the article

• How to get ISA 2006 Web Proxy to work with the Single Network Adapter template

  - by tronda

  I need to test an issue with running our application behind a proxy server with different type of configurations, so I installed ISA 2006 Enterprise on a desktop computer. Since this computer only has a single network card and I want to start out easy, I chose the "Single Network Adapter" template. We have a internal NAT'ed network which is in the 10 range. I have defined the internal network on the ISA server to be 10.XXX.YY.1 - 10.XXX.YY.255 I also have the Default rule which denies all traffic, but I've added the following Rule: Policy - Protocols - From - To Accept HTTP Internal External HTTPS Local Host Internal HTTS Server Localhost Then I configured Internet Explorer on a virutal machine running XP within virtualbox with Brigded network (gets same network address range as regular computers on our network) similar to this Instead of the server name I used the IP address. When I try to access a web page, this doesn't go through and I get the following log messages on the proxy server: Original Client IP Client Agent Authenticated Client Service Referring Server Destination Host Name Transport HTTP Method MIME Type Object Source Source Proxy Destination Proxy Bidirectional Client Host Name Filter Information Network Interface Raw IP Header Raw Payload GMT Log Time Source Port Processing Time Bytes Sent Bytes Received Cache Information Error Information Authentication Server Log Time Client IP Destination IP Destination Port Protocol Action Rule Result Code HTTP Status Code Client Username Source Network Destination Network URL Server Name Log Record Type 10.XXX.YY.174 - TCP - - - 24.08.2010 13:25:24 1080 0 0 0 0x0 0x0 - 24.08.2010 06:25:24 10.XXX.YY.174 10.XXX.YY.175 80 HTTP Initiated Connection MyHTTPAccess 0x0 ERROR_SUCCESS Internal Local Host - PROXYTEST Firewall 10.XXX.YY.175 - TCP - - - 24.08.2010 13:25:24 2275 0 0 0 0x0 0x0 - 24.08.2010 06:25:24 10.XXX.YY.175 10.XXX.YY.175 80 HTTP Initiated Connection 0x0 ERROR_SUCCESS Local Host Local Host - PROXYTEST Firewall 10.XXX.YY.175 - TCP - - - 24.08.2010 13:25:25 2275 0 0 0 0x0 0x0 - 24.08.2010 06:25:25 10.XXX.YY.175 10.XXX.YY.175 80 HTTP Closed Connection 0x80074e20 FWX_E_GRACEFUL_SHUTDOWN Local Host Local Host - PROXYTEST Firewall 10.XXX.YY.175 - TCP - - - 24.08.2010 13:25:25 2276 0 0 0 0x0 0x0 - 24.08.2010 06:25:25 10.XXX.YY.175 10.XXX.YY.175 80 HTTP Initiated Connection 0x0 ERROR_SUCCESS Local Host Local Host - PROXYTEST Firewall 10.XXX.YY.175 - TCP - - - 24.08.2010 13:25:26 2276 0 0 0 0x0 0x0 - 24.08.2010 06:25:26 10.XXX.YY.175 10.XXX.YY.175 80 HTTP Closed Connection 0x80074e20 FWX_E_GRACEFUL_SHUTDOWN Local Host Local Host - PROXYTEST Firewall 10.XXX.YY.175 - TCP - - - 24.08.2010 13:25:26 2277 0 0 0 0x0 0x0 - 24.08.2010 06:25:26 10.XXX.YY.175 10.XXX.YY.175 80 HTTP Initiated Connection 0x0 ERROR_SUCCESS Local Host Local Host - PROXYTEST Firewall 10.XXX.YY.159 - UDP - - - 24.08.2010 13:25:26 68 0 0 0 0x0 0x0 - 24.08.2010 06:25:26 10.XXX.YY.159 255.255.255.255 67 DHCP (request) Denied Connection [Enterprise] Default rule 0xc004000d FWX_E_POLICY_RULES_DENIED Internal Local Host - PROXYTEST Firewall 10.XXX.YY.166 - UDP - - - 24.08.2010 13:25:26 68 0 0 0 0x0 0x0 - 24.08.2010 06:25:26 10.XXX.YY.166 255.255.255.255 67 DHCP (request) Denied Connection [Enterprise] Default rule 0xc004000d FWX_E_POLICY_RULES_DENIED Internal Local Host - PROXYTEST Firewall 0.0.0.0 Mozilla/4.0 (compatible; MSIE 8.0; Windows NT 5.1; Trident/4.0; .NET CLR 2.0.50727; .NET CLR 3.0.4506.2152; .NET CLR 3.5.30729) Yes Proxy 10.XXX.YY.175 TCP GET Internet - - - Req ID: 096c76ae; Compression: client=No, server=No, compress rate=0% decompress rate=0% - - - 24.08.2010 13:25:27 0 2945 2581 446 0x0 0x40 24.08.2010 06:25:27 10.XXX.YY.174 10.XXX.YY.175 80 http Failed Connection Attempt MyHTTPAccess 10061 anonymous Internal Local Host http://www.vg.no/ PROXYTEST Web Proxy Filter 10.XXX.YY.175 - TCP - - - 24.08.2010 13:25:27 2277 0 0 0 0x0 0x0 - 24.08.2010 06:25:27 10.XXX.YY.175 10.XXX.YY.175 80 HTTP Closed Connection 0x80074e20 FWX_E_GRACEFUL_SHUTDOWN Local Host Local Host - PROXYTEST Firewall

  Read the article

• PHP at the root directory using Ngnix on Linode and Ubuntu 12.04

  - by Steve Kinney

  I originally set up my Linode to use it with the Sinatra applications using Phusion Passenger that I was developing and I have it working great for that. However, as time goes on, I find myself needing just a wee bit of PHP to do a server-side thing here or there. My basic set up was based off of this Linode recipe (I copied and pasted the parts that I needed—I did not install Redis and Node). If I go to http://scholarsnyc.com/index.php everything works great. If I just go the base URL however, I get a 403 Forbidden error (I have a vanilla HTML page there for now). I've played with file permissions and the same file will work if I call it directly. I've done my homework and nothing I try seems to work. I'm sure there is an obvious error. I'm also sure that there are some rookie mistakes in my Nginx configuration (some of those mistakes are the artifacts of trying different fixes from my research. user www-data www-data; worker_processes 1; events { worker_connections 1024; } upstream php { server 127.0.0.1:9001; } http { passenger_root /usr/local/lib/ruby/gems/1.9.1/gems/passenger-3.0.12; passenger_ruby /usr/local/bin/ruby; include mime.types; default_type application/octet-stream; index index.php index.html index.htm; sendfile on; keepalive_timeout 65; server { server_name localhost scholarsnyc.com www.scholarsnyc.com; root /srv/www/scholarsnyc.com/public; location / { index index.php; } location ~ \.php$ { fastcgi_pass 127.0.0.1:9000; fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name; include fastcgi_params; } } server { server_name data.scholarsnyc.com; root /srv/www/data.scholarsnyc.com/public; passenger_enabled on; } server { server_name tech.scholarsnyc.com; root /srv/www/tech.scholarsnyc.com/public; location / { root /srv/www/tech.scholarsnyc.com/public; index index.php index.html index.htm; } } } Any other optimizations are also appreciated. I literally don't know what to do at this point.

  Read the article

• i cant ping to my DMZ zone from the local inside PC

  - by Big Denzel

  HI everybody. Can anyone please help me on the following issue. I got a Cisco Asa 5520 configured at my network. I cant ping to my DMZ interface from a local inside network PC. so the only way a ping the DMZ is right from the Cisco ASA firewall, there i can pint to all 3 interfaces, Inside, Outside and DMZ,,,, But no PC from the Inside Network can access the DMZ. Can please any one help? I thank you all in advance Bellow is my Cisco ASA 5520 Firewall show run; ASA-FW# sh run : Saved : ASA Version 7.0(8) ! hostname ASA-FW enable password encrypted passwd encrypted names dns-guard ! interface GigabitEthernet0/0 description "Link-To-GW-Router" nameif outside security-level 0 ip address 41.223.156.109 255.255.255.248 ! interface GigabitEthernet0/1 description "Link-To-Local-LAN" nameif inside security-level 100 ip address 10.1.4.1 255.255.252.0 ! interface GigabitEthernet0/2 description "Link-To-DMZ" nameif dmz security-level 50 ip address 172.16.16.1 255.255.255.0 ! interface GigabitEthernet0/3 shutdown no nameif no security-level no ip address ! interface Management0/0 description "Local-Management-Interface" no nameif no security-level ip address 192.168.192.1 255.255.255.0 ! ftp mode passive access-list OUT-TO-DMZ extended permit tcp any host 41.223.156.107 eq smtp access-list OUT-TO-DMZ extended permit tcp any host 41.223.156.106 eq www access-list OUT-TO-DMZ extended permit icmp any any log access-list OUT-TO-DMZ extended deny ip any any access-list inside extended permit tcp any any eq pop3 access-list inside extended permit tcp any any eq smtp access-list inside extended permit tcp any any eq ssh access-list inside extended permit tcp any any eq telnet access-list inside extended permit tcp any any eq https access-list inside extended permit udp any any eq domain access-list inside extended permit tcp any any eq domain access-list inside extended permit tcp any any eq www access-list inside extended permit ip any any access-list inside extended permit icmp any any access-list dmz extended permit ip any any access-list dmz extended permit icmp any any access-list cap extended permit ip 10.1.4.0 255.255.252.0 172.16.16.0 255.255.25 5.0 access-list cap extended permit ip 172.16.16.0 255.255.255.0 10.1.4.0 255.255.25 2.0 no pager logging enable logging buffer-size 5000 logging monitor warnings logging trap warnings mtu outside 1500 mtu inside 1500 mtu dmz 1500 no failover asdm image disk0:/asdm-508.bin no asdm history enable arp timeout 14400 global (outside) 1 interface nat (inside) 1 0.0.0.0 0.0.0.0 static (dmz,outside) tcp 41.223.156.106 www 172.16.16.80 www netmask 255.255.255 .255 static (dmz,outside) tcp 41.223.156.107 smtp 172.16.16.25 smtp netmask 255.255.2 55.255 static (inside,dmz) 10.1.0.0 10.1.16.0 netmask 255.255.252.0 access-group OUT-TO-DMZ in interface outside access-group inside in interface inside access-group dmz in interface dmz route outside 0.0.0.0 0.0.0.0 41.223.156.108 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 timeout mgcp-pat 0:05:00 sip 0:30:00 sip_media 0:02:00 timeout uauth 0:05:00 absolute http server enable http 10.1.4.0 255.255.252.0 inside no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 telnet timeout 5 ssh timeout 5 console timeout 0 management-access inside ! ! match default-inspection-traffic ! ! policy-map global_policy class inspection_default inspect dns maximum-length 512 inspect ftp inspect h323 h225 inspect h323 ras inspect netbios inspect rsh inspect rtsp inspect skinny inspect esmtp inspect sqlnet inspect sunrpc inspect tftp inspect sip inspect xdmcp ! service-policy global_policy global Cryptochecksum: : end ASA-FW# Please Help. Big Denzel

  Read the article

• How do i enable innodb on ubuntu server 10.04

  - by Matt

  Here is my entire my.cnf [client] port = 3306 socket = /var/run/mysqld/mysqld.sock # Here is entries for some specific programs # The following values assume you have at least 32M ram # This was formally known as [safe_mysqld]. Both versions are currently parsed. [mysqld_safe] socket = /var/run/mysqld/mysqld.sock nice = 0 [mysqld] key_buffer = 224M sort_buffer_size = 4M read_buffer_size = 4M read_rnd_buffer_size = 4M myisam_sort_buffer_size = 12M query_cache_size = 44M # # * Basic Settings # # # * IMPORTANT # If you make changes to these settings and your system uses apparmor, you may # also need to also adjust /etc/apparmor.d/usr.sbin.mysqld. # user = mysql socket = /var/run/mysqld/mysqld.sock port = 3306 basedir = /usr datadir = /var/lib/mysql tmpdir = /tmp skip-external-locking # # Instead of skip-networking the default is now to listen only on # localhost which is more compatible and is not less secure. bind-address = 127.0.0.1 # # * Fine Tuning # #key_buffer = 16M max_allowed_packet = 16M thread_stack = 192K thread_cache_size = 8 # This replaces the startup script and checks MyISAM tables if needed # the first time they are touched myisam-recover = BACKUP #max_connections = 100 #table_cache = 64 #thread_concurrency = 10 # # * Query Cache Configuration # query_cache_limit = 1M #query_cache_size = 16M # # * Logging and Replication # # Both location gets rotated by the cronjob. # Be aware that this log type is a performance killer. # As of 5.1 you can enable the log at runtime! #general_log_file = /var/log/mysql/mysql.log #general_log = 1 log_error = /var/log/mysql/error.log # Here you can see queries with especially long duration #log_slow_queries = /var/log/mysql/mysql-slow.log #long_query_time = 2 #log-queries-not-using-indexes # # The following can be used as easy to replay backup logs or for replication. # note: if you are setting up a replication slave, see README.Debian about # other settings you may need to change. #server-id = 1 #log_bin = /var/log/mysql/mysql-bin.log expire_logs_days = 10 max_binlog_size = 100M #binlog_do_db = include_database_name #binlog_ignore_db = include_database_name # # * InnoDB # # InnoDB is enabled by default with a 10MB datafile in /var/lib/mysql/. # Read the manual for more InnoDB related options. There are many! # # * Security Features # # Read the manual, too, if you want chroot! # chroot = /var/lib/mysql/ # # For generating SSL certificates I recommend the OpenSSL GUI "tinyca". # # ssl-ca=/etc/mysql/cacert.pem # ssl-cert=/etc/mysql/server-cert.pem # ssl-key=/etc/mysql/server-key.pem [mysqldump] quick quote-names max_allowed_packet = 16M [mysql] #no-auto-rehash # faster start of mysql but no tab completition [isamchk] key_buffer = 16M # # * IMPORTANT: Additional settings that can override those from this file! # The files must end with '.cnf', otherwise they'll be ignored. # !includedir /etc/mysql/conf.d/ And here is my show engines call....i have no idea what i need to do to enable innodb show engines; +------------+---------+----------------------------------------------------------------+--------------+------+------------+ | Engine | Support | Comment | Transactions | XA | Savepoints | +------------+---------+----------------------------------------------------------------+--------------+------+------------+ | MyISAM | DEFAULT | Default engine as of MySQL 3.23 with great performance | NO | NO | NO | | MRG_MYISAM | YES | Collection of identical MyISAM tables | NO | NO | NO | | BLACKHOLE | YES | /dev/null storage engine (anything you write to it disappears) | NO | NO | NO | | CSV | YES | CSV storage engine | NO | NO | NO | | MEMORY | YES | Hash based, stored in memory, useful for temporary tables | NO | NO | NO | | FEDERATED | NO | Federated MySQL storage engine | NULL | NULL | NULL | | ARCHIVE | YES | Archive storage engine | NO | NO | NO | +------------+---------+----------------------------------------------------------------+--------------+------+------------+ 7 rows in set (0.00 sec)

  Read the article

• Dangers of Running Computers w/o Air Conditioning

  - by Daniel Bingham

  I recently moved in to an apartment with out air conditioning. This is fine most of the time as I am in upstate New York. It only ever gets above the high 70s during the hottest of the summer months. And when it does, I'm stubborn enough that I'll just deal with wearing minimal clothing around the house. However, I'm worried about my computers. I'm a software developer and gamer, so many of my machines are very high powered. And at least one of them is a server that must be left on 24/7 (not just a game server - also serves multiple websites). I've never before had to worry about the heat too much, as I always lived in buildings with central air. The in building temperature rarely got much above 70 F. All of the machines I built had good enough air cooling that I never saw a problem. Now the temperature in building is pushing 100F and I'm worried that the machines will not be able to keep themselves cool enough by simply blowing already hot air over themselves. The hottest of them I've turned off. However, the server I cannot. It's an old Dell (not custom build) that runs on a Pentium 4 (2.2GHz). It only has a single hard drive, integrated video. And it'd not running any processor intensive servers. Just basic LAMP. It used to run a MUD server, but that's off for now. So it should be idling most of the time. I haven't been able to find any sort of built in temperature sensors in the hardware... at least not any that the programs I've found in the Debian repository can read. And it's an inherited machine to which I do not have the full specs, so I don't know the tolerances anyway. How worried should I be about it melting down on me? How worried should I be about the hard drive melting or becoming corrupted? To generalize the question for other people, what are the safe temperature tolerances for most machines. How widely does it vary, and how does one go about determining when their machine is running too hot and needs to be shut down?

  Read the article

• Pxe net install Centos with Static IP

  - by Stu2000

  I seem to be unable to perform a kickstart installation of centos5.8 with a netinstall. It correctly gets into the text installer, but keeps sending out a request for the dhcp server and failing. I have tried to manually set the IP everywhere. Here is my pxelinux.cfg file DEFAULT menu PROMPT 0 MENU TITLE Ubuntu MAAS TIMEOUT 200 TOTALTIMEOUT 6000 ONTIMEOUT local LABEL centos5.8-net kernel /images/centos5.8-net/vmlinuz MENU LABEL centos5.8-net append initrd=/images/centos5.8-net/initrd.img ip=192.168.1.163 netmask=255.255.255.0 hostname=client101 gateway=192.168.1.1 ksdevice=eth0 dns=8.8.8.8 ks=http://192.168.1.125/cblr/svc/op/ks/profile/centos5.8-net MENU end and here is my kickstart file: # Kickstart file for a very basic Centos 5.8 system # Assigns the server ip: 192.211.48.163 # DNS 8.8.8.8, 8.8.4.4 # London TZ install url --url http://mirror.centos.org/centos-5/5.8/os/i386 lang en_US.UTF-8 keyboard us network --device=eth0 --bootproto=static --ip=192.168.1.163 --netmask=255.255.255.0 --gateway=192.168.1.1 --nameserver=8.8.8.8,8.8.4.4 --hostname=client1-server --onboot=on rootpw --iscrypted $1$Snrd2bB6$CuD/07AX2r/lHgVTPZyAz/ firewall --enabled --port=22:tcp authconfig --enableshadow --enablemd5 selinux --enforcing timezone --utc Europe/London bootloader --location=mbr --driveorder=xvda --append="console=xvc0" # The following is the partition information you requested # Note that any partitions you deleted are not expressed # here so unless you clear all partitions first, this is # not guaranteed to work part /boot --fstype ext3 --size=100 --ondisk=xvda part pv.2 --size=0 --grow --ondisk=xvda volgroup VolGroup00 --pesize=32768 pv.2 logvol swap --fstype swap --name=LogVol01 --vgname=VolGroup00 --size=528 --grow --maxsize=1056 logvol / --fstype ext3 --name=LogVol00 --vgname=VolGroup00 --size=1024 --grow %packages @base @core @dialup @editors @text-internet keyutils iscsi-initiator-utils trousers bridge-utils fipscheck device-mapper-multipath sgpio emacs Here is my dhcp file: ddns-update-style interim; allow booting; allow bootp; ignore client-updates; set vendorclass = option vendor-class-identifier; subnet 192.168.1.0 netmask 255.255.255.0 { host tower { hardware ethernet 50:E5:49:18:D5:C6; fixed-address 192.168.1.163; option routers 192.168.1.1; option domain-name-servers 8.8.8.8,8.8.4.4; option subnet-mask 255.255.255.0; filename "/pxelinux.0"; default-lease-time 21600; max-lease-time 43200; next-server 192.168.1.125; } } Is it impossible to prevent it asking for a dynamic ip before trying to install from the net? Perhaps there is an error in of my files? My dhcp server is set to ignore client-updates, and is set to only works with one mac address whilst testing.

  Read the article

• Ubuntu 14.04, OpenLDAP TLS problems

  - by larsemil

  So i have set up an openldap server using this guide here. It worked fine. But as i want to use sssd i also need TLS to be working for ldap. So i looked into and followed the TLS part of the guide. And i never got any errors and slapd started fine again. BUT. It does not seem to work when i try to use ldap over tls. root@server:~# ldapsearch -x -ZZ -H ldap://83.209.243.253 -b dc=daladevelop,dc=se ldap_start_tls: Protocol error (2) additional info: unsupported extended operation Ganking up the debug level some notches returns some more information: root@server:~# ldapsearch -x -ZZ -H ldap://83.209.243.253 -b dc=daladevelop,dc=se -d 5 ldap_url_parse_ext(ldap://83.209.243.253) ldap_create ldap_url_parse_ext(ldap://83.209.243.253:389/??base) ldap_extended_operation_s ldap_extended_operation ldap_send_initial_request ldap_new_connection 1 1 0 ldap_int_open_connection ldap_connect_to_host: TCP 83.209.243.253:389 ldap_new_socket: 3 ldap_prepare_socket: 3 ldap_connect_to_host: Trying 83.209.243.253:389 ldap_pvt_connect: fd: 3 tm: -1 async: 0 ldap_open_defconn: successful ldap_send_server_request ber_scanf fmt ({it) ber: ber_scanf fmt ({) ber: ber_flush2: 31 bytes to sd 3 ldap_result ld 0x7f25df51e220 msgid 1 wait4msg ld 0x7f25df51e220 msgid 1 (infinite timeout) wait4msg continue ld 0x7f25df51e220 msgid 1 all 1 ** ld 0x7f25df51e220 Connections: * host: 83.209.243.253 port: 389 (default) refcnt: 2 status: Connected last used: Fri Jun 6 08:52:16 2014 ** ld 0x7f25df51e220 Outstanding Requests: * msgid 1, origid 1, status InProgress outstanding referrals 0, parent count 0 ld 0x7f25df51e220 request count 1 (abandoned 0) ** ld 0x7f25df51e220 Response Queue: Empty ld 0x7f25df51e220 response count 0 ldap_chkResponseList ld 0x7f25df51e220 msgid 1 all 1 ldap_chkResponseList returns ld 0x7f25df51e220 NULL ldap_int_select read1msg: ld 0x7f25df51e220 msgid 1 all 1 ber_get_next ber_get_next: tag 0x30 len 42 contents: read1msg: ld 0x7f25df51e220 msgid 1 message type extended-result ber_scanf fmt ({eAA) ber: read1msg: ld 0x7f25df51e220 0 new referrals read1msg: mark request completed, ld 0x7f25df51e220 msgid 1 request done: ld 0x7f25df51e220 msgid 1 res_errno: 2, res_error: <unsupported extended operation>, res_matched: <> ldap_free_request (origid 1, msgid 1) ldap_parse_extended_result ber_scanf fmt ({eAA) ber: ldap_parse_result ber_scanf fmt ({iAA) ber: ber_scanf fmt (}) ber: ldap_msgfree ldap_err2string ldap_start_tls: Protocol error (2) additional info: unsupported extended operation ldap_free_connection 1 1 ldap_send_unbind ber_flush2: 7 bytes to sd 3 ldap_free_connection: actually freed So no good information there neither. In /var/log/syslog i get: Jun 6 08:55:42 master slapd[21383]: conn=1008 fd=23 ACCEPT from IP=83.209.243.253:56440 (IP=0.0.0.0:389) Jun 6 08:55:42 master slapd[21383]: conn=1008 op=0 EXT oid=1.3.6.1.4.1.1466.20037 Jun 6 08:55:42 master slapd[21383]: conn=1008 op=0 do_extended: unsupported operation "1.3.6.1.4.1.1466.20037" Jun 6 08:55:42 master slapd[21383]: conn=1008 op=0 RESULT tag=120 err=2 text=unsupported extended operation Jun 6 08:55:42 master slapd[21383]: conn=1008 op=1 UNBIND Jun 6 08:55:42 master slapd[21383]: conn=1008 fd=23 closed If i portscan the host i get the following: Starting Nmap 6.40 ( http://nmap.org ) at 2014-06-06 08:56 CEST Nmap scan report for h83-209-243-253.static.se.alltele.net (83.209.243.253) Host is up (0.0072s latency). Not shown: 996 closed ports PORT STATE SERVICE 22/tcp open ssh 80/tcp open http 389/tcp open ldap 636/tcp open ldapssl But when i check certs root@master:~# openssl s_client -connect daladevelop.se:636 -showcerts -state CONNECTED(00000003) SSL_connect:before/connect initialization SSL_connect:unknown state 140244859233952:error:140790E5:SSL routines:SSL23_WRITE:ssl handshake failure:s23_lib.c:177: --- no peer certificate available --- No client certificate CA names sent --- SSL handshake has read 0 bytes and written 317 bytes --- New, (NONE), Cipher is (NONE) Secure Renegotiation IS NOT supported Compression: NONE Expansion: NONE --- And i feel like i am clearly out in deep water not knowing at all where to go from here. Anny hints appreciated on what to do or to get better debug logging... EDIT: This is my config slapcated from cn=config and it does not mention at all anything about TLS. I have inserted my certinfo.ldif: root@master:~# cat certinfo.ldif dn: cn=config add: olcTLSCACertificateFile olcTLSCACertificateFile: /etc/ssl/certs/cacert.pem - add: olcTLSCertificateFile olcTLSCertificateFile: /etc/ssl/certs/daladevelop_slapd_cert.pem - add: olcTLSCertificateKeyFile olcTLSCertificateKeyFile: /etc/ssl/private/daladevelop_slapd_key.pem and when doing that i only got this as an answer. root@master:~# sudo ldapmodify -Y EXTERNAL -H ldapi:/// -f certinfo.ldif SASL/EXTERNAL authentication started SASL username: gidNumber=0+uidNumber=0,cn=peercred,cn=external,cn=auth SASL SSF: 0 modifying entry "cn=config" So still no wiser.

  Read the article

• Cannot connect to WEBrick on home network

  - by Chris Stewart

  I'm an Android developer and often my applications require server-side code. I typically use Ruby on Rails for the web app, and during development will run the server on my local machine (Mac OS X) with WEBrick. In the morning when I get to the office, I'll run ifconfig in the console to see what IP my laptop has been given that day. I'll use that IP in my Android app when making requests to the web app in question. This all works fine, when I'm in my office. When I get home, I attempt to do the same thing, find my laptop's IP via ifconfig, set it in my app's config file, but the destination can never be found. To exclude my app from the set of hurdles, I attempt to visit the web server IP (e.g., http://192.168.1.4:3000) from my phone's browser, and it cannot connect. If I try from my laptop, which is running the web server, it works fine. If I try from another machine, on the same network, it also is unable to connect. Given this, I think I've narrowed it down to some kind of configuration in my home network, but I frankly have no idea what the cause could be. I don't have anything special at home, your basic Verizon FiOS router/modem with everything connected via Wi-Fi (Wi-Fi for both phone and laptop at work as well, fyi). I've tried disabling the firewall on my Verizon router, enabling port forwarding, and just about everything else I could do for port 3000, and nothing has changed. Dear Server Fault geniuses, please help a poor developer out. :) Edit: Some follow up items to add. My Mac's firewall is not active, and all incoming requests are allowed. I've also verified on my phone and laptop, that they're on the same network (192.168.1.4 Mac, 192.168.1.9 Phone). I have no idea why this isn't working. Edit 2: I went into System Preferences, enabled Web Sharing, and tried to view the website from my phone and it didn't connect. So it's not WEBrick or related to Rails. The firewall on my machine is off and the firewall on my router is off. Edit 3: Some progress. I set up port forwarding for port 3000 to my laptop, found the external IP, and used that and it connected fine. So, there's definitely something not quite set up correctly on my internal network.

  Read the article

• mac + parallels and https site test = router restarts

  - by Erik

  Ok I have an interesting & very frustrating problem happening. I'm going to explain it the best I can. I work as a graphic designer & web designer on a mac and have a Comcast internet connection that comes through a Comcast branded router (SMC8014) which then ties into an Airport Extreme Base Station which runs my office network. I run OS 10.5.7 and also run Parallels 4.0.3 (running Windows XP) for testing websites in Internet Explorer and so on. Ok, so that the basic background. Here's my issue. I've been collaborating an ecommerce website with another designer/developer and when testing the site on the PC side we have started to run into some sort of network problem. The site is https if that matters at all I suspect it may. Basically when I run parallels for testing I am constantly having to restart the router in order to connect to the test site (it's hosted). Funny thing is I can access the rest of the internet fine, just not this site I'm working on until I restart the router (It's sorta like the site is timing out). This never happens when just running the Mac side of things. It only becomes an issue when Parallels is open and I am doing page refreshes while making css or HTML edits via something like Coda or CSS edit (connected to the hosting server via ftp). The real problem is that once the problem starts I only get about 2 or 3 page loads before I have to restart the router again. It's absolutely crippling. I cannot get any work done when I have to restart the router every couple of minutes. So, if you think this problem is isolated to me, the answer is no. The designer/developer I'm collaborating with has an office a couple miles away and experiences very similar problems under slightly different setup. He also has Comcast as his internet provider and connects his router to an Airport and primarily works on a mac. The main difference is that rather than using a visualizer like parallels to test the website on the PC he uses a real live PC that is on his network. Once he fire up the PC to do testing he runs into the same issue described above. After a couple of page refreshes in Internet Explorer or other browser on the PC the site becomes unresponsive and the router has to get restarted. Any thoughts on what is going on here would be greatly appreciated. Thanks in advance.

  Read the article

• Unable to telnet out on port 25 on windows server 2008

  - by NickGPS

  Hi All, I just setup a Windows 2008 R2 server and am trying to get a basic mail server up and running so that I can send emails from my applications. I setup a virtual SMTP server in IIS6 and tried doing a local telnet to port 25, which seemed to work fine. There were no errors during this stage and I can see the mail message appear in the Queue folder. The problem is that mail never leaves the Queue folder. I then tried to telnet to a remote mail server on port 25 but couldn't connect:- telnet 209.85.227.27 25 Could not open connection to the host, on port 25: Connection failed) I checked my firewall and there is a default setting to allow all outgoing TCP traffic with no restriction. I even setup a specific rule for outgoing port 25 traffic but to no avail. I then ran a SmtpDiag.exe command .\SmtpDiag.exe [email protected] [email protected] and received the following output Searching for Exchange external DNS settings. Computer name is WIN-SERVERNAME. Failed to connect to the domain controller. Error: 8007054b Checking SOA for gmail.com. Checking external DNS servers. Checking internal DNS servers. SOA serial number match: Passed. Checking local domain records. Checking MX records using TCP: gmail.com. Checking MX records using UDP: gmail.com. Both TCP and UDP queries succeeded. Local DNS test passed. Checking remote domain records. Checking MX records using TCP: gmail.com. Checking MX records using UDP: gmail.com. Both TCP and UDP queries succeeded. Remote DNS test passed. Checking MX servers listed for [email protected]. Connecting to gmail-smtp-in.l.google.com [209.85.227.27] on port 25. Connecting to the server failed. Error: 10060 Failed to submit mail to gmail-smtp-in.l.google.com. Is there any other diagnostics I can do to figure out if it's my firewall or something else? I have removed antivirus to make sure that it wasn't causing the problem. Any ideas would be much appreciated.

  Read the article

• nginx can't see MySQL

  - by user135235

  I have a fully working Joomla 2.5.6 install driven by a local MySQL server, but I'd like to test nginx to see if it's a faster web serving experience than Apache. \ PHP 5.4.6 (PHP54w) \ CentOS 6.2 \ Joomla 2.5.6 \ PHP54w-fpm.i386 (FastCGI process manager) \ php -m shows: mysql & mysqli modules loaded Nginx seems to have installed fine via yum, it can process a PHP-info file via FastCGI perfectly OK (http://37.128.190.241/php.php) but when I stop Apache, start nginx instead and visit my site I get: "Database connection error (1): The MySQL adapter 'mysqli' is not available." I've tried adjusting my Joomla configuration.php to use mysql instead of mysqli but I get the same basic error, only this time "Database connection error (1): The MySQL adapter 'mysql' is not available" of course! Can anyone think what the problem might be please? I did try explicitly setting extension = mysqli.so and extension = mysql.so in my php.ini to try and force the issue (despite php -m showing they were both successfully loaded anyway) - no difference. I have a pretty standard nginx default.conf: server { listen 80; server_name www.MYDOMAIN.com; server_name_in_redirect off; access_log /var/log/nginx/localhost.access_log main; error_log /var/log/nginx/localhost.error_log info; root /var/www/html/MYROOT_DIR; index index.php index.html index.htm default.html default.htm; # Support Clean (aka Search Engine Friendly) URLs location / { try_files $uri $uri/ /index.php?q=$uri&$args; } # deny running scripts inside writable directories location ~* /(images|cache|media|logs|tmp)/.*\.(php|pl|py|jsp|asp|sh|cgi)$ { return 403; error_page 403 /403_error.html; } location ~ \.php$ { fastcgi_pass 127.0.0.1:9000; fastcgi_index index.php; include fastcgi_params; fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name; include /etc/nginx/fastcgi.conf; } # caching of files location ~* \.(ico|pdf|flv)$ { expires 1y; } location ~* \.(js|css|png|jpg|jpeg|gif|swf|xml|txt)$ { expires 14d; } } Snip of output from phpinfo under nginx: Server API FPM/FastCGI Virtual Directory Support disabled Configuration File (php.ini) Path /etc Loaded Configuration File /etc/php.ini Scan this dir for additional .ini files /etc/php.d Additional .ini files parsed /etc/php.d/curl.ini, /etc/php.d/fileinfo.ini, /etc/php.d/json.ini, /etc/php.d/phar.ini, /etc/php.d/zip.ini Snip of output from phpinfo under Apache: Server API Apache 2.0 Handler Virtual Directory Support disabled Configuration File (php.ini) Path /etc Loaded Configuration File /etc/php.ini Scan this dir for additional .ini files /etc/php.d Additional .ini files parsed /etc/php.d/curl.ini, /etc/php.d/fileinfo.ini, /etc/php.d/json.ini, /etc/php.d/mysql.ini, /etc/php.d/mysqli.ini, /etc/php.d/pdo.ini, /etc/php.d/pdo_mysql.ini, /etc/php.d/pdo_sqlite.ini, /etc/php.d/phar.ini, /etc/php.d/sqlite3.ini, /etc/php.d/zip.ini Seems that with Apache, PHP is loading substantially more additional .ini files, including ones relating to mysql (mysql.ini, mysqli.ini, pdo_mysql.ini) than nginx. Any ideas how I get nginix to also call these additional .ini's ? Thanks in advance, Steve

  Read the article

• hyperv machine guest loads slow

  - by Dani Avni

  this is by far one of the strangest things I have seen. I have a win 2008R2 cluster with a CSV. the CSV itself is on an iSCSI storage (hitachi HUS 110) basic config of the two hosts in the cluster is Dell R610 Win 2008 R2 with all patches 64GB 1 NIC for host access 2 NICs for guest access 2 NICs for iSCSI these machine work great and I can load a 2008R2 test guest machine on them in less than 90 seconds after the above config is running for over a year, I now need to add a new host. now the host is Dell R620 (Still intel but different CPU) Win 2008 R2 with all patches 64GB 1 NIC for host access 2 NICs for guest access 2 NICs for iSCSI I added this new host to the domain and to the cluster, I gave it access to the CSV and I tried loading the same guest machine that loads in 90 seconds in the other hosts. the machine loads in about 6 minutes. no matter how many times I try this the old hosts load the machine in about 90 seconds and this new host in around 6 minutes to eliminate any problems with the iSCSI connection, I added a new LUN and directly accessed it from the new host and I was working at around 300MB/s so no problem there. I also tested the connection between the other hosts and the new one and network is working fine there too. to eliminate problems in HyperV, I copied the machine to the local disk of the new host and it loaded in less than 20 seconds. now is the point were things get a lot stranger: in my tests I tried installing a fresh windows guest machine to the CSV from the new host. I noticed that while the fresh windows was installing, my test guest was loading in less than 90 seconds even on the new host (I repeated this a few times). If I paused the fresh install guest and tried loading the test guest again it loaded in 6 minutes. and again after I resumed the guest installation the test guest loaded fast. after the fresh windows was also loaded, I ran tests loading the fresh window and my test machine. each one of them loaded in about 5 minutes when I tried loading them separately. however when I started both of them in the same time they both loaded in around 2.5 minutes it seems that the iSCSI disk access is only working if it is under some load (although I never got to above 10% utilization according to the task manager) does anyone have any idea what could be the problem?

  Read the article

• BIND DNS server (Windows) - Unable to access my local domain from other computers on LAN

  - by Ricardo Saraiva

  I have a BIND DNS server running on my Windows 7 development machine and I'm serving pages with WAMPSERVER. My ideia is to develop some tools (in PHP) for my intranet at work and I want them to be accessible via LAN in this format: http://tools.mycompany.com I've already placed BIND and I can access http://tools.mycompany.com on the machine that holds BIND server, but I cannot access it from other LAN computers. I've done the following on my router: defined static IP's for all LAN computers set Port Forwarding to my server (remember: it serves DNS and Web pages) set DNS server configuration to point to my LAN server On LAN computers, I went to Local Area Network properties and also changed the DNS server IP in order to point to my local DNS server. If it helps, here is my named.conf file: options { directory "c:\windows\SysWOW64\dns\etc"; forwarders {127.0.0.1; 8.8.8.8; 8.8.4.4;}; pid-file "run\named.pid"; allow-transfer { none; }; recursion no; }; logging{ channel my_log{ file "log\named.log" versions 3 size 2m; severity info; print-time yes; print-severity yes; print-category yes; }; category default{ my_log; }; }; zone "mycompany.com" IN { type master; file "zones\db.mycompany.com.txt"; allow-transfer { none; }; }; key "rndc-key" { algorithm hmac-md5; secret "qfApxn0NxXiaacFHpI86Rg=="; }; controls { inet 127.0.0.1 port 953 allow { 127.0.0.1; } keys { "rndc-key"; }; }; ...and a single zone I've defined - file db.mycompany.com.txt: $TTL 6h @ IN SOA tools.mycompany.com. hostmaster.mycompany.com. ( 2014042601 10800 3600 604800 86400 ) @ NS tools.mycompany.com. tools IN A 192.168.1.4 www IN A 192.168.1.4 On the file above 192.168.1.4 is the IP of the local machine inside my LAN. Can someone help me here? I need my web pages to be accessible from other computers inside my LAN using my custom domain name. I've tried on other computers and they can access my server via http://192.168.1.4/, but no able when using http://tools.mycompany.com . Please, consider the following: I'm completely new to BIND I have basic knowledge in Apache configuration Thanks a lot for your help.

  Read the article

• DPM 2010 PowerShell Script to Easily Restore Multiple Files

  - by bmccleary

  I’ve got what I thought would be a simple task with Data Protection Manager 2010 that is turning out to be quite frustrating. I have a file server on one server and it is the only server in a protection group. This file server is the repository for a document management application which stores the files according to the data within a SQL database. Sometimes users inadvertently delete files from within our application and we need to restore them. We have all the information needed to restore the files to include the file name, the folder that the file was stored in and the exact date that the file was deleted. It is easy for me to restore the file from within the DPM console since we have a recovery point created every day, I simply go to the day before the delete, browse to the proper folder and restore the file. The problem is that using the DPM console, the cumbersome wizard requires about 20 mouse clicks to restore a single file and it takes 2-4 minutes to get through all the windows. This becomes very irritating when a client needs 100’s of files restored… it takes all day of redundant mouse clicks to restore the files. Therefore, I want to use a PowerShell script (and I’m a novice at PowerShell) to automate this process. I want to be able to create a script that I pass in a file name, a folder, a recovery point date (and a protection group/server name if needed) and simply have the file restored back to its original location with some sort of success/failure notification. I thought it was a simple basic task of a backup solution, but I am having a heck of a time finding the right code. I have seen the sample code at http://social.technet.microsoft.com/wiki/contents/articles/how-to-use-a-windows-powershell-script-to-recover-an-item-in-data-protection-manager.aspx that I have tried to follow, but it doesn’t accomplish what I really want to do (it’s too simplistic) and there are errors in the sample code. Therefore, I would like to get some help writing a script to restore these files. An example of the known values to restore the data are: DPM Server: BACKUP01 Protection Group: Document Repository Data Protected Server: FILER01 File Path: R:\DocumentRepository\ToBackup\ClientName\Repository\2010\07\24\filename.pdf Date Deleted: 8/2/2010 (last recovery point = 8/1/2010) Bonus Points: If you can help me not only create this script, but also show me how to automate by providing a text file with the above information that the PowerShell script loops through, or even better, is able to query our SQL server for the needed data, then I would be more than willing to pay for this development.

  Read the article

• Windows Server 2008 Software Raid 5 - Data integrity issues

  - by Fopedush

  I've got a server running Windows Server 2008 R2, with a (windows native) software raid-5 array. The array consists of 7x 1TB Western Digital RE3 and RE4 drives. I have offline backups of this array. The problem is this: I noticed a few days ago after copying a large file to the disk that there was an integrity issue with that file - it was a ~12GB file that I had downloaded via uTorrent. After moving it to the raid array, I used uTorrent to relocate the download location, and performed a re-check so I could seed it from that location. The recheck found that only 6308/6310 chunks of the copied file were intact. My next step was to write a quick powershell script that would copy files to the array, while performing a SHA1 hash of the original and resultant files and comparing them. Smaller files (100-1000MB) copied over just fine. When I started copying larger data (~15GB), I found that the hash check failed about 2/3rds of the time. The corrupt files had very, very small inconsistencies - less than .01%. I further eliminated the possibility of networking or client issues by placing this large file on the C:\ of the server, and copying it repeatedly from there to the array, seeing similar results. Copying the data via explorer, powershell, or the standard windows command prompt yield the same results. None of the copies fail or report any problems. The raid array itself is listed as healthy in disk management. After a few experiments, I shut down the server and ran memtest overnight. No errors were detected. A basic run of chkdsk found no problems, but I did not use the /R flag, as I was unsure how that might affect a software raid-5 volume. I next ran Crystal Disk Info to check the smart data on the drives - but found that CDI only detected 5 out of 7 of the disks in the array. I have no idea why. Nevertheless, CDI shows the following "caution" flags on a single one of the drives: 05 199 199 140 000000000001 Reallocated Sectors Count C5 200 200 __0 000000000001 Current Pending Sector Count Which is a little bit alarming, but I don't really know what to do with the information. I hardly feel like one reallocated sector could be causing this. At this point, I'm looking for some guidance on what to do next. I need to determine the cause of this issue, but I'm hesitant to run chkdsk /R or any bootable disk health checkers because I'm afraid they might break the array. I've considered triggering a re-sync of the array, but I'm not actually sure how to do that without doing something silly like manually dropping a disk and then restoring it. Any advice that could help me ferret out the precise cause of this issue would be greatly appreciated.

  Read the article

• Loss of wireless network connectivity when playing video via HDMI cable

  - by Jeff Fohl

  Hi Folks - New to Super User, so I hope this question fits in with the guidelines. Very strange problem I am having, and I am at a loss as to how to continue troubleshooting this one. The basic problem is that when I attempt to watch streamed video on a particular display device (an Optoma HD180 projector), my network connectivity drops like a stone to barely measurable levels. This is my setup: I have a Dell H2C 730x running Windows 7 64bit. This particular computer has two ATI Radeon HD 4800 video cards. I have two Samsung 22" monitors connected to one card, and an Optoma HD180 digital projector connected to the other card via an HDMI cable. My internet connection is normally a reliable 6Mbps. The problem I am having occurs when I stream video (or even just browse the web) on the Optoma Projector. When I do this, my internet connection drops to practically zero (just a few kilobits per second). When I move the browser away from the projector, and over to one of my Samsung monitors, the internet connection comes right back. Note that the Optoma projector is on and enabled as a third monitor all this time. I can move the mouse around on the projector without triggering the problem. I tried pinging my router when I was playing a movie on one of the monitors, and I get a 1 millisecond response. However, when I have the movie playing on the Optoma projecter, pinging the router gives me response times in the hundreds of milliseconds, or times out completely. So, it clearly is something local to my machine - and not some sort of throttling occurring down the line. I would think that it is possibly something to do with the HDMI driver conflicting somehow with my network driver (which is a USB-based wireless connection). This one has me really stumped. Anyone have any ideas? EDIT: I am now leaning towards the possibility that the HDMI cable is somehow interfering with the wireless network, when large amounts of data are being pushed through the cable. Is this possible?

  Read the article

• can't access nginx server from IP

  - by EquinoX

  So 2 days ago I can see that page where it saya "Welcome to nginx", however as of now when I tried to access it, it says 404 page not found... Why is this? Inside my sites-enabled folder I have a file named default and it has the following: # You may add here your # server { # ... # } # statements for each of your virtual hosts server { listen 80; server_name 127.0.0.1; access_log /var/log/nginx/localhost.access.log; location / { root /var/www/nginx-default; index index.html index.htm; } location /doc { root /usr/share; autoindex on; allow 127.0.0.1; deny all; } location /images { root /usr/share; autoindex on; } #error_page 404 /404.html; # redirect server error pages to the static page /50x.html # #error_page 500 502 503 504 /50x.html; #location = /50x.html { # root /var/www/nginx-default; #} # proxy the PHP scripts to Apache listening on 127.0.0.1:80 # #location ~ \.php$ { #proxy_pass http://127.0.0.1; #} # pass the PHP scripts to FastCGI server listening on 127.0.0.1:9000 # location ~ \.php$ { fastcgi_pass 127.0.0.1:9000; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME /var/www/nginx-default$fastcgi_script_name; include fastcgi_params; } # deny access to .htaccess files, if Apache's document root # concurs with nginx's one # location ~ /\.ht { deny all; } } # another virtual host using mix of IP-, name-, and port-based configuration # #server { #listen 8000; #listen somename:8080; #server_name somename alias another.alias; #location / { #root html; #index index.html index.htm; #} #} # HTTPS server # #server { #listen 443; #server_name localhost; #ssl on; #ssl_certificate cert.pem; #ssl_certificate_key cert.key; #ssl_session_timeout 5m; #ssl_protocols SSLv2 SSLv3 TLSv1; #ssl_ciphers ALL:!ADH:!EXPORT56:RC4+RSA:+HIGH:+MEDIUM:+LOW:+SSLv2:+EXP; #ssl_prefer_server_ciphers on; #location / { #root html; #index index.html index.htm; #} #} Here's my nginx.conf file: user www-data; worker_processes 4; error_log /var/log/nginx/error.log; pid /var/run/nginx.pid; events { worker_connections 1024; # multi_accept on; } http { include /etc/nginx/mime.types; access_log /var/log/nginx/access.log; sendfile on; #tcp_nopush on; #keepalive_timeout 0; keepalive_timeout 65; tcp_nodelay on; gzip on; gzip_disable "MSIE [1-6]\.(?!.*SV1)"; include /etc/nginx/conf.d/*.conf; include /etc/nginx/sites-enabled/*; } # mail { # # See sample authentication script at: # # http://wiki.nginx.org/NginxImapAuthenticateWithApachePhpScript # # # auth_http localhost/auth.php; # # pop3_capabilities "TOP" "USER"; # # imap_capabilities "IMAP4rev1" "UIDPLUS"; # # server { # listen localhost:110; # protocol pop3; # proxy on; # } # # server { # listen localhost:143; # protocol imap; # proxy on; # } # } What am I doing wrong here? I have other virtual host setup in the sites-enabled as well... UPDATE: The server_name directives are: -admin.api.frapi -api.frapi -default -example.com -php.example.com

  Read the article

• Squid - Logging to MySQL without empty rows/skipped records?

  - by Lee Ward

  I'm trying to figure out how to make Squid proxy log to MySQL. I know ACL order is pretty important but I'm not sure if I understand exactly what ACLs are or do, it's difficult to explain, but hopefully you'll see where I'm going with this as you read! I have created the lines to make Squid interact with a helper in squid.conf as follows: external_acl_type mysql_log %LOGIN %SRC %PROTO %URI php /etc/squid3/custom/mysql_lg.php acl ex_log external mysql_log http_access allow ex_log The external ACL helper (mysql_lg.php) is a PHP script and is as follows: error_reporting(0); if (! defined(STDIN)) { define("STDIN", fopen("php://stdin", "r")); } $res = mysql_connect('localhost', 'squid', 'testsquidpw'); $dbres = mysql_select_db('squid', $res); while (!feof(STDIN)) { $line = trim(fgets(STDIN)); $fields = explode(' ', $line); $user = rawurldecode($fields[0]); $cli_ip = rawurldecode($fields[1]); $protocol = rawurldecode($fields[2]); $uri = rawurldecode($fields[3]); $q = "INSERT INTO logs (id, user, cli_ip, protocol, url) VALUES ('', '".$user."', '".$cli_ip."', '".$protocol."', '".$uri."');"; mysql_query($q) or die (mysql_error()); if ($fault) { fwrite(STDOUT, "ERR\n"); }; fwrite(STDOUT, "OK\n"); } The configuration I have right now looks like this: ## Authentication Handler auth_param ntlm program /usr/bin/ntlm_auth --helper-protocol=squid-2.5-ntlmssp auth_param ntlm children 30 auth_param negotiate program /usr/bin/ntlm_auth --helper-protocol=squid-2.5-basic auth_param negotiate children 5 # Allow squid to update log external_acl_type mysql_log %LOGIN %SRC %PROTO %URI php /etc/squid3/custom/mysql_lg.php acl ex_log external mysql_log http_access allow ex_log acl localnet src 172.16.45.0/24 acl AuthorizedUsers proxy_auth REQUIRED acl SSL_ports port 443 acl Safe_ports port 80 # http acl Safe_ports port 21 # ftp acl Safe_ports port 443 # https acl CONNECT method CONNECT acl blockeddomain url_regex "/etc/squid3/bl.acl" http_access deny blockeddomain deny_info ERR_BAD_GENERAL blockeddomain # Deny requests to certain unsafe ports http_access deny !Safe_ports # Deny CONNECT to other than secure SSL ports http_access deny CONNECT !SSL_ports # Allow the internal network access to this proxy http_access allow localnet # Allow authorized users access to this proxy http_access allow AuthorizedUsers # FINAL RULE - Deny all other access to this proxy http_access deny all From testing, the closer to the bottom I place the logging lines the less it logs. Oftentimes, it even places empty rows in to the MySQL table. The file-based logs in /var/log/squid3/access.log are correct but many of the rows in the access logs are missing from the MySQL logs. I can't help but think it's down to the order I'm putting lines in because I want to log everything to MySQL, unauthenticated requests, blocked requests, which category blocked a specific request. The reason I want this in MySQL is because I'm trying to have everything managed via a custom web-based frontend and want to avoid using any shell commands and access to system log files if I can help it. The end result is to make it as easy as possible to maintain without keeping staff waiting on the phone whilst I add a new rule and reload the server! Hopefully someone can help me out here because this is very much a learning experience for me and I'm pretty stumped. Many thanks in advance for any help!

  Read the article

< Previous Page | 555 556 557 558 559 560 561 562 563 564 565 566  | Next Page >