Search Results

Search found 18937 results on 758 pages for 'missing controls'.

Page 561/758 | < Previous Page | 557 558 559 560 561 562 563 564 565 566 567 568  | Next Page >

• Plesk wildcard subdomain not working

  - by avdgaag

  I'm trying to set up a wildcard subdomain on my VPS. Ultimately I want to end up with this: main site: my.domain.tld subdomain: sub1.my.domain.tld - should end up serving my.domain.tld/sub1 I am using plesk 8.6. I have created a DNS A record pointing at my VPS' IP. I have then restarted the DNS server and waited up to 24 hours. But trying ping sub1.my.domain.tld results in an unknown host error. So I know there's more stuff involved, configuring apache etc. But so far, I cannot even get the subdomain working at all, let alone serve up the right content. I have also tried a CNAME record, to no effect. I have also tried creating a regular subdomain with a fixed name, which also does not work. Pre-configured subdomains DO work, like ftp.my.domain.tld or mail.my.domain.tld. I am clearly missing something here, but my hosting provider charges a small fortune for any support request not involving hardware physically burning down, so I'm hesitant to ask them. Any ideas?

  Read the article

• Cisco SG200 vlan issue in ESXi VSA cluster

  - by George

  I have three Cisco SG200-26 switches, and I also have two ESXi hosts that I have connected like shown in the below "best practice" map by VMware: http://communities.vmware.com/servlet/JiveServlet/previewBody/17393-102-1-22458/VSA_networking_map.pdf Even though I created the VLANs in the SG200 and I set the two VLANs (508 and 608) as allowed for these untagged ports (where my ESX NIC's are connected), I can not ping from host 1 to host 2 when configuring the NIC's to use 608 VLAN. Am I missing something? my IP's are all in the 192.168. range, and the only reason I need the VLANs is to isolate the traffic of VSA back-end internally, only the two hosts will be using the VLANs. So I think I do not have to create virtual interfaces on my router since that's the case, is my understanding correct? Also sending my switch config screenshot below.. all 3 switches have the latest firmware (it seems these were originally linksys and got rebranded as cisco after the acquisition) http://img31.imageshack.us/img31/2503/switch.gif Any ideas what to change on the Cisco SG200 to make this work , would be appreciated! The second VLAN (608) only needs two IP's: 192.168.0.1 and 192.168.0.2 The first VLAN (508) will have about 15 IP's for ESXi Management and VSA cluster service, I could use either 192.168.1.xx or 10.0.1.xx The rest of my network (about 50 clients) is in 192.168.1.xx range VMware also states that the VLAN protocol on the physical switch must be 802.1Q, not ISL, anyone knows which of the two my SG200-26 uses? In addition to that, the only requirement from VSA is that my two hosts: -Are in the same subnet. -Have static IP addresses set. -Have the same Default Gateway configured. If I need inter-vlan routing for this, I suppose I have to create virtual interfaces on my sonicwall, and assign an IP for each VLAN, and then set routes between them? Thank you for your time!

  Read the article

• Nginx as a proxy to Jetty

  - by user36812

  Pardon me, this is my first attempt at Nginx-Jetty instead of Apache-JK-Tomcat. I deployed myapp.war file to $JETTY_HOME/webapps/, and the app is accessible at the url: http://myIP:8080/myapp I did a default installation of Nginx, and the default Nginx page is accessible at myIP Then, I modified the default domain under /etc/nginx/sites-enabled to the following: server { listen 80; server_name mydomain.com; access_log /var/log/nginx/localhost.access.log; location / { #root /var/www/nginx-default; #index index.html index.htm; proxy_pass http://127.0.0.1:8080/myapp/; } error_page 500 502 503 504 /50x.html; location = /50x.html { root /var/www/nginx-default; } } Now I get the index page of mypp (running in jetty) when I hit myIP, which is good. But all the links are malformed. eg. The link to css is mydomain.com/myapp/css/style.css while what it should have been is mydomain.com/css/style.css. It seems to be mapping mydomain.com to 127.0.0.1:8080 instead of 127.0.0.1:8080/myapp/ Any idea what am missing? Do I need to change anything on the Jetty side too?

  Read the article

• pfsense 2.0.1 Firewall SMB Share not showing up under network

  - by atrueresistance

  I have a freenas NAS with a SMB share running at 192.168.2.2 of a 192.168.2.0/28 network. Gateway is 192.168.2.1. Originally this was running on a switch with my LAN, but now having upgraded to new hardware the Freenas has it's own port on the firewall. Before the switch the freenas would show up under Network on a windows 7 box and an OSX Lion box as freenas{wins} or CIFS shares on freenas{osx} so I know it doesn't have anything do to with the freenas. Here are my pfsense rules. ID Proto Source Port Destination Port Gateway Queue Schedule Description PASS TCP FREENAS net * LAN net 139 (NetBIOS-SSN) * none cifs lan passthrough PASS TCP FREENAS net * LAN net 389 (LDAP) * none cifs lan passthrough PASS TCP FREENAS net * LAN net 445 (MS DS) * none cifs lan passthrough PASS UDP FREENAS net * LAN net 137 (NetBIOS-NS) * none cifs lan passthrough PASS UDP FREENAS net * LAN net 138 (NetBIOS-DGM) * none cifs lan passthrough BLOCK * FREENAS net * LAN net * * none BLOCK * FREENAS net * OPTZONE net * * none BLOCK * FREENAS net * 192.168.2.1 * * none PASS * FREENAS net * * * * none BLOCK * * * * * * none I can connect if I use \\192.168.2.2 and enter the correct login details. I would just like this to show up on the network. Nothing in the log seems to be blocked when I filter by 192.168.2.2. What port am I missing for SMB to show up under the network and not have to connect by IP? ps. Do I really need the LDAP rule?

  Read the article

• 3GB RAM Installed and Detected by BIOS, Windows Vista 32bit Only Sees 2GB

  - by Nathan Taylor

  I am attempting to install more RAM on a Windows Vista 32bit machine which is using a X6DAL-XG motherboard and the RAM amount reported in the BIOS is 3GB+, but Windows is only reporting 2GB installed. The motherboard has 6 RAM bays which I have populated with various combinations of 4 1GB sticks, and 2 512mb sticks, but no matter how I configure them Windows doesn't see more than 2GB. I realize of course 32-bit Windows has a 3gb cap on memory, but that doesn't explain why it will only report 2GB when there are in fact (currently) 5GB installed. I should think I would be able to see at least 3GB. According to the spec list for the motherboard the minimum RAM requirements are DDR333/266mhz installed in pairs. I have done this exactly, and the BIOS isn't reporting any problems at POST. RAM Configuration (according to CPU-Z): Slot #1: Kingston 128mx72D266C25 - 1024mb PC2100 (133mhz) Slot #2: Kingston KVR266X72RC25/1024 - 1024mb PC2100 (133mhz) Slot #3: PQI - 512mb PC2700 (166mhz) Slot #4: Kingston 128mx72D266C25 - 1024mb PC2100 (133mhz) Slot #5: Kingston KVR266X72RC25/1024 - 1024mb PC2100 (133mhz) Slot #6: PQI - 512mb PC2700 (166mhz) I'm not sure if memory specs above conflict with this statement in the motherboard manual or not: Memory Support The X6DAL-XG supports up to 12GB/24GB of registered ECC DDR333/266 (PC2700/PC2100) memory. The motherboard was designed to support 4GB (PC2100) modules in each slot, but only the 2GB modules have been tested. When using registered ECC DDR333 (PC2700) memory, installing four pieces of double-banked memory or six pieces of single-banked memory is supported. So, am I doing something wrong with the RAM I have now, or is there some sort of compatibility problem which I am missing? Thanks!

  Read the article

• Outside VPN traffic not able to ping site-to-site VPN remote site

  - by Siriss

  we have two ASA 5510s running 8.4 in a site-to-site VPN setup. All internal traffic is working smoothly. Site/Subnet A: 192.100.0.0 - local Site/Subnet B: 192.200.0.0 - remote VPN Users: 192.100.40.0 - assigned by ASA When you VPN into the network, all traffic hits Site A, and everything on subnet A is accessible. Site B however, is completely inaccessible for VPN users. All machines on subnet B, the firewall itself, etc... is not reachable by ping or otherwise. I know I am missing a NAT rule, and in 8.2, it was easy as pie to setup using ASDM, but now I can't get it for the life of me as 8.4 apparently made a lot of changes to NAT rules. I am not too comfortable in the ASA command line, but if there is a command I need to add or if you could direct me where I can add this in 8.4 ASDM I would really appreciate it. I have tired NAT Exempt, Static NAT, Static NAT Policies, etc... I think I tried all the options. I also might have my interfaces confused with the new look at feel of ASDM. Thank you much in advance and I hope I have been thorough enough.

  Read the article

• pure-ftpd not listening on specified port

  - by Jason McLaren

  I installed the pure-ftpd package (version 1.0.35-1) on an Ubuntu 12.04 box (an EC2 instance based on the standard Ubuntu 12.04 AMI). The pure-ftpd daemon is running (verified with ps), though there is no PID file (expected one to be created by the /etc/init.d/pure-ftpd script). Here's the resulting command that gets run by the init.d script: /usr/sbin/pure-ftpd -l pam -O clf:/var/log/pure-ftpd/transfer.log -o -8 UTF-8 -u 1000 -E -B -g /var/run/pure-ftpd/pure-ftpd.pid Here's my real problem: the ftp server isn't actually listening on any port (checked with netstat and nmap). So I can't ftp to the server (either locally using localhost or remotely using the public IP address). I tried adding a Bind file to /etc/pure-ftpd/conf and restarting, but it didn't help. When I installed pure-ftpd, it replaced inetd with openbsd-inetd, but did not run it since there were no services enabled. So inetd is not listening on port 21 either. (Apparently Ubuntu has a no-inetd-by-default policy, according to https://lists.ubuntu.com/archives/ubuntu-users/2010-September/227905.html .) I want to run pure-ftpd by itself (not with inetd) anyways, since the /etc/init.d/pure-ftpd script requires no inetd if you use the UploadScript feature. I'm not familiar with how Ubuntu handles network services (and can't find any relevant docs besides generic man pages), so I'm probably missing something obvious. Nothing seems out of the ordinary with /etc/hosts.allow (empty) or hosts.deny (empty), and I didn't add any firewall rules (iptables -L shows that the firewall is in its initial state). I've checked the pure-ftpd docs; not sure what else to look at. Any help would be appreciated, thanks!

  Read the article

• Xbox 360 formatting for MP4 h.264?

  - by Kayle

  For the life of me, I can't get the Xbox 360 to recognize anything other than a WMV. It's full updated with Xbox Live and I even added all the Video apps (Zune, Netflix, etc) just to see if it would force some sort of codec update. I'm using handbrake, at the moment, to try and convert an mkv with subtitles. Handbrake burns the subtitles into the video for me, which is important. I can't figure out what is missing though, as the Xbox refuses to acknowledge my MP4s. Here's the VLC codec info output: As far as I can tell, this is EXACTLY what the xbox supports. I don't want to convert every video twice by throwing it through Windows Movie Maker just to get it to WMV. None of the converters mentions above output to WMV and I don't like WMV since it's not as universal as MP4. I've tried changing the container name manually to M4V, MOV, and AVI to see if I can trick the Xbox... no beans. The video displays perfectly in WMP, of course. If I convert it to WMV, suddenly it works fine. But I don't find this acceptable, as I know the Xbox is supposed to support other filetypes. If anyone knows why my Xbox won't play anything but WMVs, I would be very appreciative to know why! It's driving me nuts. The only other information I can think to include is that it's about 3 years old and of the cheapest variety (Xbox Arcade). I've added a hard drive, xbox live, and have thoroughly updated it. Maybe there's a specific video update I'm unaware of??

  Read the article

• nginx does not use variables set in /etc/environment on system reboot, but does when restarted from shell

  - by Dave Nolan

  I have a Rails app running on nginx/passenger. It restarts happily in a shell using sudo /etc/init.d/nginx stop|start|restart. But Passenger throws an error when the system is rebooted: "Missing the Rails #{version} gem". But GEM_HOME and GEM_PATH are both set in /etc/environment so surely they would be available to all processes during reboot? /etc/environment PATH="/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin:/usr/bin/X11:/usr/games" GEM_HOME=/var/lib/gems/1.8 GEM_PATH=/var/lib/gems/1.8 /etc/init.d/nginx #! /bin/sh ### BEGIN INIT INFO # Provides: nginx # Required-Start: $all # Required-Stop: $all # Default-Start: 2 3 4 5 # Default-Stop: 0 1 6 # Short-Description: starts the nginx web server # Description: starts nginx using start-stop-daemon ### END INIT INFO PATH=/usr/local/sbin:/usr/local/bin:/sbin:/bin:/usr/sbin:/usr/bin DAEMON=/opt/nginx/sbin/nginx NAME=nginx DESC=nginx test -x $DAEMON || exit 0 # Include nginx defaults if available if [ -f /etc/default/nginx ] ; then . /etc/default/nginx fi set -e case "$1" in start) echo -n "Starting $DESC: " start-stop-daemon --start --quiet --pidfile /var/log/nginx/$NAME.pid \ --exec $DAEMON -- $DAEMON_OPTS echo "$NAME." ;; stop) echo -n "Stopping $DESC: " start-stop-daemon --stop --quiet --pidfile /var/log/nginx/$NAME.pid \ --exec $DAEMON echo "$NAME." ;; restart|force-reload) echo -n "Restarting $DESC: " start-stop-daemon --stop --quiet --pidfile \ /var/log/nginx/$NAME.pid --exec $DAEMON sleep 1 start-stop-daemon --start --quiet --pidfile \ /var/log/nginx/$NAME.pid --exec $DAEMON -- $DAEMON_OPTS echo "$NAME." ;; reload) echo -n "Reloading $DESC configuration: " start-stop-daemon --stop --signal HUP --quiet --pidfile /var/log/nginx/$NAME.pid \ --exec $DAEMON echo "$NAME." ;; *) N=/etc/init.d/$NAME echo "Usage: $N {start|stop|restart|force-reload}" >&2 exit 1 ;; esac exit 0 $ opt/nginx/sbin/nginx -v nginx version: nginx/0.7.67 Ubuntu lucid

  Read the article

• Migrating from "partial" Exchange 2003 to full Exchange 2003 usability

  - by TheCleaner

  I have a client that is using Exchange 2003 on SBS 2003 R2, but only for calendar sharing and contacts sharing. Their email is still coming to their clients via a POP3 account on each client's Outlook. I'd like to move them over to using Exchange for both email and the other things they are utilizing it for now. Can you folks guide me in the right direction? The setup: external domain is akin to domain.com (and is where they get their POP3 email from now) internal domain is akin to domain.local only simple hardware firewall (no ISA) static external IP is available to use My "assumptions": Setup SMTP default connector in Exchange for their existing external domain Have their existing email backed up to PST files (just in case) Setup the new MX records to point domain.com to the static external IP I'm a little confused how I'm going to setup their existing Exchange accounts with the proper SMTP address though. Right now it is just [email protected]. Do I just need to modify or create a new recipient policy? Are there other steps involved that I'm missing? Anyone with a walkthrough or even a basic "steps" is fine. I'm fairly used to Exchange 03, but I've been on Exchange 07 for a while now so going back is the weird part...plus I don't know what issues Exchange 03 on SBS has versus the normal "version". Thanks for all the help!

  Read the article

• Making OpenSSL work on PHP Windows 2008 server with FastCGI

  - by KacieHouser

  I have been researching all day. Here is what I have done: In C:/PHP/php.ini and C:/PHP/php-cgi-fcgi.ini I have made the extension_dir = "C:/PHP/ext" I uncommented extension=php_openssl.dll I went to http://windows.php.net/download/ and got the thread safe version with the PHP 5.4 (5.4.8) version of DLL's In C:/PHP/ext I replaced the php_openssl.dll with the one I downloaded In System32 and SysWOW64 I added the following DLL's ssleay.dll libeay.dll I restarted the IIS server in the Server Manager under Web Server and stopped and started the World Wide Web Publishing Service That didn't work, so I tried same thing with the unthreaded versions. I still get: Fatal error: Call to undefined function ftp_ssl_connect() in C:\inetpub\wwwroot\REMOVED_dev\save_data.php on line 5 Here are related things from phpinfo(): System Windows NT DEV-WEB1 6.1 build 7601 (Windows Server 2008 R2 Standard Edition Service Pack 1) i586 Compiler MSVC9 (Visual C++ 2008) Architecture x86 Configure Command cscript /nologo configure.js "--enable-snapshot-build" "--enable-debug-pack" "--disable-zts" "--disable-isapi" "--disable-nsapi" "--without-mssql" "--without-pdo-mssql" "--without-pi3web" "--with-pdo-oci=C:\php-sdk\oracle\instantclient10\sdk,shared" "--with-oci8=C:\php-sdk\oracle\instantclient10\sdk,shared" "--with-oci8-11g=C:\php-sdk\oracle\instantclient11\sdk,shared" "--with-enchant=shared" "--enable-object-out-dir=../obj/" "--enable-com-dotnet" "--with-mcrypt=static" "--disable-static-analyze" "--with-pgo" Server API CGI/FastCGI Configuration File (php.ini) Path C:\Windows Loaded Configuration File C:\PHP\php-cgi-fcgi.ini Scan this dir for additional .ini files (none) Additional .ini files parsed (none) Registered PHP Streams php, file, glob, data, http, ftp, zip, compress.zlib, compress.bzip2, https, ftps, sqlsrv, phar Registered Stream Socket Transports tcp, udp, ssl, sslv3, sslv2, tls FTP support enabled Protocols dict, file, ftp, ftps, gopher, http, https, imap, imaps, ldap, pop3, pop3s, rtsp, scp, sftp, smtp, smtps, telnet, tftp openssl OpenSSL support enabled OpenSSL Library Version OpenSSL 0.9.8t 18 Jan 2012 OpenSSL Header Version OpenSSL 0.9.8x 10 May 2012 What am I missing here?

  Read the article

• ASA DHCP Relay configuration..

  - by Jeff

  I have locations in different cities, connected using 2 Cisco ASA devices. my main location, corporate, use the IP 192.168.1.x The second location, remote store, use the IP 192.168.3.x I have a DHCP server (192.168.1.254) at my corporate location. I have created a scope for the 192.168.1.x which works fine for the corporate location. I created a scope for the remote location (192.168.3.x) on my DHCP server and tried to configure the remote ASA DCHP Relay, on the remote ASA: I disabled the DHCP Server on the inside. I enabled DHCP Relay on the inside, with set route set at yes. I set the Global DHCP Relay Servers, specify up to four servers to which DHCP requests would be relayed. I added my DHCP, 192.168.1.254 I flashed these settings to the ASA and gave it a try, didn't do anything. am i missing something - forgetting something. not really sure what im doing wrong. DHCP Settings on remote ASA: dhcp-client update dns server both dhcpd dns 192.168.1.254 dhcpd ping_timeout 750 dhcpd domain JEWELS.LOCAL dhcpd auto_config outside dhcpd update dns both ! dhcpd address 192.168.3.2-192.168.3.33 inside ! dhcprelay server 192.168.1.254 outside dhcprelay enable inside dhcprelay setroute inside on my local ASA: i have two ACLs for UDP ports 67 and 68 permitting any inbound traffic from the remote locations IP ... dhcprelay timeout 120

  Read the article

• SNAT through Racoon IPSec VPN

  - by Mite fine d'ailes

  I am trying to route traffic from a device (that I will call "target") connected to my Ubuntu box (that I will call "host") to servers at a remote office. The host uses a Racoon IPSec VPN, connected through a NIC called efix. This creates an aliased IF called efix:0 which has IP adress 192.168.190.132. It is able to reach the servers. The link between host and target is an Ethernet link, using IP adresses 10.0.0.1 on IF eusb for the host and 10.0.0.2 on IF eth0 for the target. I have setup the following routes and iptables entries: On target: 10.0.0.0 * 255.255.255.0 U 0 0 0 eth0 default 10.0.0.1 0.0.0.0 UG 0 0 0 eth0 On host: echo 1 > /proc/sys/net/ipv4/ip_forward iptables -t nat -A POSTROUTING -s 10.0.0.0/24 -j SNAT --to 192.168.190.132 iptables -A FORWARD -s 10.0.0.0/24 -j ACCEPT iptables -A FORWARD -d 10.0.0.0/24 -j ACCEPT Using Wireshark to monitor an HTTP GET, I can see SYN packets from the target go all the way to the server, but the server's SYNACK packets stop at the host and are not forwarded to the target. Am I missing something here ? Isn't SNAT supposed to keep track of the connections ?

  Read the article

• Can reprepro accept a new version of a package into the repository?

  - by kai

  I have installed a package into my own debian package repository like so: $ sudo reprepro -b /var/packages/ubuntu includedeb maverick my-package_0.8-0_all.deb my-package_0.8-0_all.deb: component guessed as 'main' Exporting indices... I have installed my package on a few machines using apt-get install. I have now added new features to my software and would like to add a new minor version of my package to the repository so that I may update my machines using apt-get upgrade. I try to do this like so: $ sudo reprepro -b /var/packages/ubuntu includedeb maverick my-package_0.9-0_all.deb my-package_0.9-0_all.deb: component guessed as 'main' Skipping inclusion of 'my-package' '1.0-0' in 'maverick|main|i386', as it has already '1.0-0'. Skipping inclusion of 'my-package' '1.0-0' in 'maverick|main|amd64', as it has already '1.0-0'. It looks like I need to tell reprepro that this is a new version of the same package but I have no idea how to do this. I have read the reprepro man page several times and searched on the net for a couple of hours but I have not found any answers. Am I missing something? Many thanks.

  Read the article

• likewise-open and samba as pdc

  - by Knight Samar

  Hi, We have successfully implemented a Samba Primary Domain Controller for a hybrid Windows-Linux environment. So now I am setting up dual-boot clients with Windows XP and Ubuntu 9.10. Windows XP can be easily added to the Samba Domain. Everything is manageable. No worries. But when I try using likewise-open 4.1 to add the Ubuntu 9.10 to the samba domain, it cannot locate the domain controller. domainjoin-cli --loglevel verbose join MYDOMAIN root Error: Unable to resolve DC name [code 0x00080026] Resolving 'MYDOMAIN' failed. Check that the domain name is correctly entered. Also check that your DNS server is reachable, and that your system is configured to use DNS in nsswitch. I even tried mydomain.com variations but to no avail. What am I missing ? I read up a document on MSDN wherein it says that the Domain Controller creates some SRV records in the DNS server. I guess, I don't have them on my BIND. Do you think that is the problem ? If yes, can anyone please point out how and what SRV records need to be added. Thanks.

  Read the article

• Compiling mod_auth_kerb on OS X

  - by bshacklett

  I'm trying to get mod_auth_kerb installed, but I can't seem to find any information on compiling it on OS X. I'm getting the following when I attempt to compile: ./apxs.sh "-I. -Ispnegokrb5 -I/include " "-dynamic -g -O2 -arch x86_64 -Wl,-search_paths_first -lgssapi_krb5 -lkrb5 -lk5crypto -lcom_err -lresolv -lresolv" "" "/Applications/XAMPP/xamppfiles/bin/apxs" "-c" "src/mod_auth_kerb.c" /Applications/XAMPP/xamppfiles/build/libtool --silent --mode=compile gcc -prefer-pic -I/Applications/XAMPP/xamppfiles/include -L/Applications/XAMPP/xamppfiles/lib -mmacosx-version-min=10.4 -arch i386 -arch ppc -DDARWIN -DSIGPROCMASK_SETS_THREAD_MASK -no-cpp-precomp -I/Applications/XAMPP/xamppfiles/include -I/Applications/XAMPP/xamppfiles/include -I/Applications/XAMPP/xamppfiles/include -I/Applications/XAMPP/xamppfiles/include -I. -Ispnegokrb5 -I/include -c -o src/mod_auth_kerb.lo src/mod_auth_kerb.c && touch src/mod_auth_kerb.slo src/mod_auth_kerb.c: In function ‘authenticate_user_krb5pwd’: src/mod_auth_kerb.c:1030: warning: passing argument 8 of ‘verify_krb5_user’ discards qualifiers from pointer target type src/mod_auth_kerb.c: In function ‘authenticate_user_krb5pwd’: src/mod_auth_kerb.c:1030: warning: passing argument 8 of ‘verify_krb5_user’ discards qualifiers from pointer target type /Applications/XAMPP/xamppfiles/build/libtool --silent --mode=link gcc -o src/mod_auth_kerb.la -dynamic -g -O2 -arch x86_64 -Wl,-search_paths_first -lgssapi_krb5 -lkrb5 -lk5crypto -lcom_err -lresolv -lresolv -rpath /Applications/XAMPP/xamppfiles/modules -module -avoid-version src/mod_auth_kerb.lo ld: warning: in src/.libs/mod_auth_kerb.o, missing required architecture x86_64 in file warning: no debug symbols in executable (-arch x86_64) I'm configuring as follows: ./configure --with-krb4=no CFLAGS='-g -O2 -arch x86_64' I should mention that I'm using XAMPP with the development package on this machine.

  Read the article

• How often is CRL refreshed, and how to force it to be?

  - by lockstock

  I have a web service running under IIS 7 that requires an X509 client certificate. I know that the server that it rus on needs access to DigiCert.com in order to be able to get the CRL (Certificate Revocation List). There is a need to change our proxy so I am attempting to investigate the impact of doing so. I have removed the global proxy settings using the command netsh winhttp proxy refesh, and also deleted the CRL cache using the command certutil -URLcache CRL delete. However, after doing this, all calls to the web service still succeed. This suggests to me that I am missing something here. So; If the CRL cache is cleared and the server has no way of refreshing the CRL, why do web service requets not return http 403?. I have been unable to find adequate information from googling nor from my colleagues. The reason I want it to fail is that I will not be confident that the new proxy settings work until I can see it broken first, if that makes sense. I would also like to be able to force the CRL to be refeshed in order to ensure that the new proxy settings work

  Read the article

• Accessing network shares on Windows7 via SonicWall VPN client

  - by Jack Lloyd

  I'm running Windows7 x64 (fully patched) and the SonicWall 4.2.6.0305 client (64-bit, claims to support Windows7). I can login to the VPN and access network resources (eg SSH to a machine that lives behind the VPN). However I cannot seem to be able to access shared filesystems. Windows is refusing to do discovery on the VPN network. I suspect part of the problem is Windows persistently considers the VPN connection to be a 'public network'. Normally, you can open the network and sharing center and modify this setting, however it does not give me a choice for the VPN. So I did the expedient thing and turned on file sharing for public networks. I also disabled the Windows firewall for good measure. Still no luck. I can access the server directly by putting \\192.168.1.240 in the taskbar, which brings up the list of shares on the server. However, trying to open any of the shares simply tells me "Windows cannot access \\192.168.1.240\share You do not have permission to access ..."; it never asks for a domain password. I also tried Windows7 native VPN functionality - it couldn't successfully connect to the VPN at all. I suspect this is because SonicWall is using some obnoxious special/undocumented authentication system; I had similar problems trying to connect on Linux with the normal IPsec tools there. What magical invocation or control panel option am I missing that will let this work? Are there any reasonable debugging strategies? I'm feeling quite frustrated at Windows tendency to not give me much useful information that might let me understand what it is trying to do and what is going wrong.

  Read the article

• Rsync Push files from linux to windoes. ssh issue - connection refused

  - by piyush c

  For some reason I want to run a script to move files from Linux machine to Windows. I have installed cwRsync on my windows machine and able to connect to linux machine. When i execute following command: rsync -e "ssh -l "piyush"" -Wgovz --timeout 120 --delay-updates --remove-sent-files /usr/local/src/piyush/sync/* "[email protected]:/cygdrive/d/temp" Where 10.0.0.60 is my widows machine and I am running above command on Linux - CentOS 5.5. After running command I get following error message: ssh: connect to host 10.0.0.60 port 22: Connection refused rsync: connection unexpectedly closed (0 bytes received so far) [sender] rsync error: error in rsync protocol data stream (code 12) at io.c(463) [sender=2.6.8] [root@localhost sync]# ssh [email protected] ssh: connect to host 10.0.0.60 port 22: Connection refused I have modified my firewall settings on widows to allow all ports. I think this issue is due to SSH Daemon not present on my windows machine. So I tried installing OpenSSH on my machine and running ssh-agent but didn't helped. I tried similar command to run on my widows machine to pull files from Linux and its working fine. For some reason I want command for Linux machine so that I can embed it in a shell script. Can you suggest me if I am missing anything. I am already having cwRsync installed on my widows and running it in daemon mode using --damemon option. And I am able to login using ssh from windows machine to linux machine. When I issue bellow command, it just blocks for 120 seconds (timeout I specified in command) and exits saying there is timeout. rsync -e "ssh -l piyush" -Wgovz --timeout 120 --delay-updates --remove-sent-files /usr/local/src/piyush/sync/* "[email protected]:/cygdrive/d/temp" After starting rsync on widows, I checked, rsyc is running. And widows firewall setting are set to minimal, and on Linux machine stopped iptables service so that port 873 (default rsync port) is not blocked. What can be the possible reason that Linux machine is not able to connect to rsync-daemon on windows machine?

  Read the article

• linked-server sql - access

  - by user22121

  Hi, I have a SQL server 2000 and an Access database mdb connected by Linked server on the other hand I have a program in c # that updates data in a SQL table (Users) based data base access. When running my program returns the following error message: OLE DB provider 'Microsoft.Jet.OLEDB.4.0' reported an error. Authentication failed. [OLE / DB provider returned message: Can not start the application. Missing information file of the working group or is opened exclusively by another user.] OLE DB error trace [OLE / DB Provider 'Microsoft.Jet.OLEDB.4.0' IDBInitialize:: Initialize returned 0x80040E4D: Authentication failed.] . Both the program, the sql server and database access are on a remote server. On the local server the problem was solved by running the following: "sp_addlinkedsrvlogin 'ActSC', 'false', NULL, 'admin', NULL". Try on the remote server the next, without result: "sp_addlinkedsrvlogin 'ActSC', true, null, 'user', 'pass'". On the remote server and from the "Query Analyzer" sql update statements are working correctly. Can you think of what may be the problem? Thanks!

  Read the article

• DFS replication and the SYSTEM user (NTFS permissions)

  - by HopelessN00b

  Question for which I'm having trouble finding an answer on Google or Technet... Does granting the SYSTEM user permissions to DFS-shared files and folders have any effect on DFS replication? (And while we're at it, is there any good reason not to let SYSTEM have permissions to DFS-shared files?) It comes up because I have a collection of DFS namespaces and folders that I'm not able to make someone else's problem, and while troubleshooting a problem where one DFS replica just wasn't replicating with another for no discernible reason, I observed that the SYSTEM didn't have any permissions granted to any of the files or folders in the folder in question. So I set SYSTEM to have full control and propagated it down, and our DFS health diagnostic reports went from showing a backlog of ~80 files to a backlog of ~100,000... and things started replicating, including a number of files that had been missing on one server or the other (so more than just the permissions changes started replicating). Naturally, this made me curious as to whether or not DFS needs the SYSTEM account to have permissions to do its work, or if perhaps it was just any change to folder tree in question that prompted DFS to jump into action. If it matters, our DFS namespaces were set up under 2000/2003, and I have just recently finished upgrading all the servers to 2008 R2 or 2012 (with UAC enabled, blech), but have not yet gotten around to raising the DFS namespace functional levels to Server 2008. (And bonus points if anyone has an official Microsoft article on NTFS file permissions and the SYSTEM account as it pertains to DFS or network files.)

  Read the article

• r1soft agent is failing with the error: "write error while sending code: Broken pipe"

  - by curiousguy

  I have an Ubuntu 10.04.4 LTS server with r1soft agent installed in it. Recently, the backups are failing with the following error. -------- write error while sending code: Broken pipe -------- I have reinstalled the buagent but to no avail. On checking the server logs, I could see the following errors listed in it: -------- # tail -f /var/log/messages |grep -i buagent Nov 17 03:35:06 microscope buagent: Need to back up 126 sectors Nov 17 03:35:06 microscope buagent: (Righteous Backup Linux Agent) 1.79.0 build 12433 Nov 17 03:35:06 microscope buagent: allowing control from backup server (10.128.136.195) with valid RSA key Nov 17 03:35:06 microscope buagent: allowing control from backup server (10.128.136.201) with valid RSA key Nov 17 03:35:06 microscope buagent: sending auth challenge for allowed host at (10.128.136.201) port (47890) Nov 17 03:35:06 microscope buagent: host (10.128.136.201) port (47890) authentication successful Nov 17 03:35:06 microscope buagent: Backup request accepted. Starting backup. Nov 17 03:35:06 microscope buagent: Snapshot completed in 0.010 seconds. Nov 17 03:45:03 microscope buagent: Error reading blocks from snapshot. Nov 17 03:45:03 microscope buagent: Reading blocks failed Nov 17 03:45:03 microscope buagent: error backup aborted Nov 17 03:45:03 microscope buagent: backup failed on agent closing connection Nov 17 03:45:03 microscope buagent: Backup failed. Nov 17 03:45:03 microscope buagent: write error while sending code: Broken pipe (32) Nov 17 03:45:03 microscope buagent: tell child write failed -------- I tried changing the 'Timeout' and 'DiskAsPartition' value in '/etc/buagent/agent_config' file but no luck. Also, verified that proper route is added to the backup server. The agent is also running fine. Am I missing anything? Any help would be much appreciated. Note: CDP 2.0 is installed in the backup server.

  Read the article

• In Windows 7, why can't I use perfmon against a remote server?

  - by SomeGuy

  I am on Windows 7 and trying to run perfmon against Windows 2003 and Windows 2008 servers. I am running into the same issue with all remote machines. When creating a data collector set, I specify a domain account that is in the administrators group on the remote machines (and "Performance Log Users" and "Performance Monitor Users" to be safe). On the "Available Counters" screen, When I type in a remote computer name, PerfMon locks up for a good 2-3 minutes before I can add any counters. I can then save the collector set. However, when I save it, the go/stop buttons are disabled if I click the set in the left panel, and missing if I click the Data collector set itself in the right panel. See the screens below. I can run data collector sets against my local machine with no problem. I am opening perfmon with my local account in both scenarios. I also have Remote Registry Service started on each remote machine. What is going on?

  Read the article

• HP Procurve Issue Passing Multiple VLANs over a link

  - by MichaelRwat

  Just to start off with I am a Cisco guy that got placed into an HP project. Basic topology overview from outside in: ASA 5505 with two Ethernet connections to a 2910-24 port switch. This switch is then (Cisco Trunking) to a 2626 switch passing vlan (1 untagged and 100 tagged)between them. I created SVI's on each of the switches for both VLAN's for testing purposes. I can not get vlan 100 to pass across this link. I also have trunks configured to AP's off of the switch and can not ping the vlan 100 BVI on the AP's but can reach the vlan 1 BVI. Port 25 on Access layer (2626) connects (trunks) with port A1 of 2610. STP is not running at all on any switch (this is not my network I can't change this nor did I design this) Distribution Sw: MP1-0# show run ip default-gateway 10.100.100.100 vlan 1 name "DATA" untagged 1-22,24-A1,B1 ip address 10.100.100.6 255.255.255.0 no untagged 23 exit vlan 100 name "GUEST" untagged 23 tagged 24-A1 ip address 10.100.102.6 255.255.255.0 exit Access Sw: ip default-gateway 10.100.100.100 vlan 1 name "DEFAULT_VLAN" untagged 1-26 ip address 10.100.100.5 255.255.255.0 exit vlan 100 name "GUEST" ip address 10.100.102.5 255.255.255.0 tagged 15,25 exitt From the ASA I can ping the vlan 100 address of the 2610 but not the 2626 (10.100.102.6)[Not passing the "trunk"] If I plug into an access port vlan 100 of the 2626 I can ping the SVI for vlan 100 as intended. I can not ping across the "trunk" over vlan 100 but I can across vlan 1. There may be something obvious I'm missing but please review my configuration and thank you for the assistance.

  Read the article

• Data Protection Manager System Protection Backups Failing

  - by TrueDuality

  I'm just starting to setup DPM 2010 in a test environment with a Domain Controller and a File Server. Everything seem to be working fairly well and I can get all of my backup jobs to succeed except for the "Computer\System Protection" backups. Both servers are running fully up to date 64 bit Windows Server 2008 R2 Enterprise with Service Pack 1. The error that is being provided is: DPM cannot create a backup because Windows Server Backup (WSB) on the protected computer encountered an error (WSB Event ID: 517, WSB Error Code: 0x8078001D). (ID 30229 Details: Internal error code: 0x809909FB) This Microsoft Knowledge Base article describes the issue perfectly and provides a hotfix. I downloaded the hotfix, moved it onto the affected server, attempt to run it and receive the following error: The update is not applicable to your computer. I've verified that I have indeed downloaded the 64 bit version. According to this thread the hotfix got rolled into Service Pack 1, yet I'm still experiencing the issue. Both machines do have the Windows Server Backup feature installed. Can anybody point me in the right direction? What am I missing?

  Read the article

< Previous Page | 557 558 559 560 561 562 563 564 565 566 567 568  | Next Page >