Search Results

Search found 18249 results on 730 pages for 'real world haskell'.

Page 566/730 | < Previous Page | 562 563 564 565 566 567 568 569 570 571 572 573  | Next Page >

• bond0:0 + define virtual IP

  - by yael

  hi all in my linux server I have the follwoing: Linux Version - RedHat-Linux- 5.3.0.0 (this linux server only only one LAN) more /etc/sysconfig/network-scripts/ifcfg-bond0:0 DEVICE=bond0:0 ONBOOT=yes BOOTPROTO=static IPADDR=10.10.10.12 NETMASK=255.255.255.0 ifconfig -a bond0 Link encap:Ethernet HWaddr 00:00:00:00:00:00 UP BROADCAST MASTER MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) bond0:0 Link encap:Ethernet HWaddr 00:00:00:00:00:00 inet addr:10.10.10.12 Bcast:1.1.1.255 Mask:255.255.255.0 UP BROADCAST MASTER MULTICAST MTU:1500 Metric:1 eth0 Link encap:Ethernet HWaddr 00:0E:0C:C7:F8:92 inet addr:1.1.1.1 Bcast:1.1.1.255 Mask:255.255.255.0 inet6 addr: fe80::20e:cff:fec7:f892/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:8600 errors:0 dropped:0 overruns:0 frame:0 TX packets:4764 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:717979 (701.1 KiB) TX bytes:598620 (584.5 KiB) Memory:b8820000-b8840000 my problems: why I get HWaddr 00:00:00:00:00:00 and not the real MAC address I cant ping to other server with 10.10.10.11 from my server is it posible to define bond0:0 when I have only one LAN (eth0) other info: more /etc/modprobe.conf alias eth0 e1000e alias eth1 e1000e alias eth2 e1000e alias eth3 e1000e alias scsi_hostadapter mptbase alias scsi_hostadapter1 mptsas alias scsi_hostadapter2 ata_piix alias bond0 bonding alias bond1 bonding

  Read the article

• clocksource tsc unstable

  - by amorfis

  Ok, now I have real server fault ;) After some time from booting (about one minute) my server hangs. All I can do is hard reset. Then after restart in /var/log/kern.log I can find: Jul 29 22:38:57 leonidas kernel: [ 90.729598] longhaul: Failed to set requested frequency! Jul 29 22:38:57 leonidas kernel: [ 90.731252] longhaul: Enabling "Ignore Revision ID" option. Jul 29 22:38:57 leonidas kernel: [ 91.201461] longhaul: Failed to set requested frequency! Jul 29 22:38:57 leonidas kernel: [ 91.201482] longhaul: Disabling ACPI C3 support. Jul 29 22:38:57 leonidas kernel: [ 91.204230] longhaul: Disabling "Ignore Revision ID" option. Jul 29 22:38:58 leonidas kernel: [ 91.416133] longhaul: Failed to set requested frequency! Jul 29 22:38:58 leonidas kernel: [ 91.416152] longhaul: Enabling "Ignore Revision ID" option. Jul 29 22:38:58 leonidas kernel: [ 91.960048] Clocksource tsc unstable (delta = -105611479 ns) I found some resources on the net, and it said to change clocksource, or disable ACPI. I tried disabling ACPI but it didn't help (but I noticed there was longer time before hanging). I can't change clock to hpet, because my system doesn't have such one. Output of cat /sys/devices/system/clocksource/clocksource0/available_clocksource: acpi_pm jiffies tsc My system is ubuntu server on VIA Epia hardware.

  Read the article

• my cpu won't start. all fan were spinning for a second then nothing happen

  - by Tommy

  I need help about this.. I'm from Malaysia.. Back then my cpu is all okay..and it's 4 year old.. I think this question is answered before but i'm still don't understand.. when i plugged my cpu..turn it on and all of the fan (graphic card, mobo fan and PSU fan) were spinning just for a second than nothing happen.. I don't know if it is because of the PSU or my mobo.. I sent my cpu to the shop and they said it must be the mobo.. They tell me to change my mobo and PSU also..and it cost over 100 buck (rm300 in Malaysia). and i'm real 'dry' right now. My whole data is inside the HDD. School projects, photos, games, and many..I really-really need my cpu back alive.. My mobo is MSI MS-7529 with dual core chips. My PSU is ATX-480W. the PC store guy said i need to change to new ASUS mobo if I want. I dont know what type it is but Then he tell me to change my PSU also because he don't think my old PSU (ATX-480W) ain't compatible to the new mobo.. I was very need a help from you techie guys.. sorry for my terrible English..

  Read the article

• How to access XAMPP virtual hosts from iPad on local network?

  - by martin's

  Using XAMPP on one machine. Multiple virtual hosts defined. One per project. Format is .local For example: apple.local microsoft.local client-site.local our-own-internal-site.local All works perfectly from that one machine. I now want to have other systems within the network access the various sites. The main reason for wanting to do this is to be able to test site functionality and layout from mobile devices without having to upload partial work to public servers. I can access the main XAMPP default site by simply entering the IP address of the XAMPP machine in, say, Safari on an iPad. However, there is no way to reach .local that I can see. Would this entail setting up a DNS server within the network? We have a mixture of Windows and Mac machines. No Linux. The XAMPP machine is Vista 64. I don't want real external internet access to be affected in any way, just ".local" pointed to the XAMPP machine if that makes sense.

  Read the article

• Could I use Windows 7 instead of Windows SBS 2008 for this server?

  - by Ecyrb

  First off, I'm not a sys admin. I'm just a software developer trying to help out my parents' small business. Right now they have one server, a domain controller with a P4 processor running SBS 2003. They also have this machine hosting QuickBooks, MySQL for the old version of an app, and SQL Server 2008 Express for the new version of the app (which will replace the old eventually). They've been complaining about the workstations being slow so I figured it might help if they bought a new server and moved QuickBooks, MySQL, and SQL Server to the new server, leaving the old server as just a DC. In trying to pick an operating system for their new server, I was thinking about Windows SBS 2008 Standard with enough licenses for seven machines. But that's a lot more money than they're going to want to spend. So then I wondered if there's any real advantage to having a server OS as opposed to just throwing Windows 7 on the new server. It's a lot cheaper and I can't think of any SBS features that it would need if it's just hosting QuickBooks, MySQL, and SQL Server. Would it be okay to use Windows 7 for a server like this? Are there any advantages to using SBS 2008 that I would be missing out on? Any additional tips are much appreciated!

  Read the article

• Viewing Postscript (or PDF) on OS X: Aliasing issues

  - by mankoff

  I am generating postscript graphics and am trying to find a balance between non-aliasing and over-aliasing. If I use the raw ghostscript viewer gs on the Postscript, it looks good. The text appears anti-aliased, but the image remains nice and blocky. Unfortunately, gs has no real user interface and loses all of the nice things that Preview.app has. I could install gv, but the dependency bloat is huge! It requires all of gnome. And even that isn't a great viewer compared to Preview.app or Skim.app. Here is an image viewed with gs: From a user-interaction and Mac-ish perspective, Preview.app (or Skim.app is a much nicer program to use. They have the option to turn on or off aliasing, but neither option looks very good. Which aliasing on, the image is blurry. When it is off, the graphic matches what is seen from gs, but there are two issues. Minor issue: the font is ugly. Uglier than with gs. Major issue: Every PDF is un-aliased, making it hard to read regular PDFs full of text. So, in summary: Is there a way to manually generate the PDF from the PS that overcomes these issues? Is there a way to find a middle ground of alias/unalias with Preview.app? Is there another app that displays with quality like gs, but has a decent UI like Skim.app or Preview.app Is there a way to have Preview.app turn off aliasing for only one file (containing graphics) but leave it enabled in general so that text PDFs are still readable?

  Read the article

• SSH Keys Authentication keeps asking for password

  - by Rhyuk

  Im trying to set access from ServerA(SunOS) to ServerB(Some custom Linux with Keyboard Interactive login) with SSH Keys. As a proof of concept I was able to do it between 2 virtual machines. Now in my real life scenario it isnt working. I created the keys in ServerA, copied them to ServerB, chmod'd .ssh folders to 700 on both ServerA,B. Here is the log of what I get. debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-ctr hmac-md5 none debug1: kex: client->server aes128-ctr hmac-md5 none debug1: Peer sent proposed langtags, ctos: debug1: Peer sent proposed langtags, stoc: debug1: We proposed langtags, ctos: en-US debug1: We proposed langtags, stoc: en-US debug1: SSH2_MSG_KEX_DH_GEX_REQUEST sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug1: dh_gen_key: priv key bits set: 125/256 debug1: bits set: 1039/2048 debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug1: Host 'XXX.XXX.XXX.XXX' is known and matches the RSA host key. debug1: Found key in /XXX/.ssh/known_hosts:1 debug1: bits set: 1061/2048 debug1: ssh_rsa_verify: signature correct debug1: newkeys: mode 1 debug1: set_newkeys: setting new keys for 'out' mode debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: newkeys: mode 0 debug1: set_newkeys: setting new keys for 'in' mode debug1: SSH2_MSG_NEWKEYS received debug1: done: ssh_kex2. debug1: send SSH2_MSG_SERVICE_REQUEST debug1: got SSH2_MSG_SERVICE_ACCEPT debug1: Authentications that can continue: publickey,keyboard-interactive debug1: Next authentication method: publickey debug1: Trying private key: /XXXX/.ssh/identity debug1: Trying public key: /xxx/.ssh/id_rsa debug1: Authentications that can continue: publickey,keyboard-interactive debug1: Trying private key: /xxx/.ssh/id_dsa debug1: Next authentication method: keyboard-interactive Password: Password: ServerB has pretty limited actions since its a custom propietary linux. What could be happening? EDIT WITH ANSWER: Problem was that I didnt have those settings enabled in the sshd_config (Refer to accepted answer) AND that while pasting the key from ServerA to ServerB it would interpret the key as 3 separate lines. What I did was, in case you cant use ssh-copy-id like I couldnt. Paste the first line of your key in your "ServerB" authorized_keys file WITHOUT the last 2 characters, then type yourself the missing characters from line 1 and the first one from line 2, this will prevent adding a "new line" between the first and second line of the key. Repeat with the 3d line.

  Read the article

• Is there a limit to how many sites can be hosted on a single IP address when using HTTP Host Headers on Windows 2008?

  - by Kev

  For reasons that are lost in the mists of time, our older Windows (2000, 2003) servers have been configured with a "Administrative" IP address and three further "Hosting" IP addresses. There are also additional IP's for sites with SSL certificates. The "Administrative" IP address is where all our internal provisioning, monitoring and other such apps are bound to. We lock this down and don't permit access to it from the outside world (other than over our VPN). The three "Hosting" IP addresses are used for IIS website hosting (in conjunction with host headers). Historically, new site IP address allocations have been rotated through these three IP addresses. I'm not really sure why. I'm building a new batch of servers and I'm considering just having a single hosting IP address. Our servers can host up to 1200 sites on a single machine. Is there a technical limit to the number of IIS sites that can bind to a single IP address? Our Linux platform seems to do just fine with just a single shared IP + host headers. I initially thought this might be an SEO thing, but given that IPv4 address space conservation is paramount I hardly think Google or other search engines could reasonably penalise site rankings just because hundreds of sites hang off the same IP.

  Read the article

• Convert MPG w/ AC3 audio to something else - on a Mac

  - by anonymous coward

  I'm helping with a small volunteer media team, and they have several .mpg videos that don't appear to have sound when played in QuickTime, iTunes, Real Player, etc, on the local Mac machine. I was able to hear audio after transferring one of the movies to a Windows machine that had VLC media player on it. Through VLC I was able to discover that the audio stream is a52 / AC3 format. We use Autodesk Cleaner in our normal workflow of converting the format of our videos to FLV, but for some reason it's unable to convert this particular batch of videos (well, the video converts fine, but with no audio). Obviously, it seems that there's a codec issue here, but I'm not sure how to correct it. (I'm not extremely familiar with Macs, and/or Autodesk Cleaner). I've seen the Perian codec pack, but I'm not sure that having the codecs on the system will enable Cleaner to convert these videos (particularly the audio stream, since the video converts fine). Is there something obvious that I'm overlooking, or will we have to use something else for this particular batch of videos? If so, what?

  Read the article

• SFTP access without hassle

  - by enobayram

  I'm trying to provide access to a local folder for someone over the internet. After googling around a bit, I've come to the conclusion that SFTP is the safest thing to expose through the firewall to the chaotic and evil world of the Internet. I'm planning to use the openssh-server to this end. Even though I trust that openssh will stop a random attacker, I'm not so sure about the security of my computer once someone is connected through ssh. In particular, even if I don't give that person's user account any privileges whatsoever, he might just be able to "su" to, say, "nobody". And since I was never worried about such things before, I might have given some moderate privileges to nobody at some point (not sudo rights surely!). I would of course value your comments about giving privileges to nobody in the first place, but that's not the point, really. My aim is to give SFTP access to someone in such a sandboxed state that I shouldn't need to worry about such things (at least not more so than I should have done before). Is this really possible? Am I speaking nonsense or worried in vain?

  Read the article

• HAProxy crashes on all requests in 1.5-dev12

  - by Daniel Hough

  I'm having an issue where HAProxy is crashing with no explanation when I switch from 1.4.12 to 1.5-dev12. The reason I'm switching is for the SSL offloading. My config file doesn't have any errors, it's quite simple and it works well with 1.4 - but for some reason when I run it with 1.5-dev12 I see the logs noting that the two backends I have have been set up, and then when I hit one of the frontends, I get an HTTP 400 in the browser and suddenly HAProxy isn't running anymore when I check. I understand that a common workaround to the lack of SSL support for HAProxy is to use Stud, and I may go with that since I am in need of an SSL solution for my service, but before I dele into that world I thought I might see if anybody has experienced the same problems and might know how to fix it. The server is Ubuntu 10.04 and I followed the make instructions on the Exceliance blog here. EDIT: On the advice of Kyle Brandt, I did a bit more investigation. I attached gdb to the haproxy process and when the crash occurred this is what I got: Program received signal SIGSEGV, Segmentation fault. 0x0804e5c2 in dequeue_all_listeners (list=0x9e1a418) at src/protocols.c:184 184 list_for_each_entry_safe(listener, l_back, list, wait_queue) { P.S. HAProxy is awesome, so thank you Exceliance for providing us with something so useful :)

  Read the article

• Windows disk change monitoring for malware analysis

  - by SuperDuck

  Not sure if this question belongs to here, because it has some relations with 'serverfault' (system backups) and 'stackoverflow' (software analysis). I'm looking for a solution to monitor disk changes on a Windows system and selectively revert them. It should be able to handle live files like registry parts, so may need to be an offline backup software. It shouldn't silently pass over files which the current admin user doesn't have permissions on (files with no permission entries or owned by the 'system' user) Registry change tracking would be a bonus but is not a requirement I use virtual machines for malware analysis, there is even no solution to list file changes in disk snapshot files (delta VMDK). I currently use Ashampoo for monitoring changes. Though it's the best one between similars, it's not a good software and hasn't really evolved in many 'platinum', 'deluxe' versions released in the last 10 years (it even used non-resizable windows until the latest version). The real problem is it misses some disk / registry changes. Perhaps it only compares modification dates and doesn't catch a change if the dates are preserved. So, I think the solution should compare files using hashes, or file sizes at least. There are numerous backup software out there and I'm sure one can handle this, offline or online.

  Read the article

• Macvlan based interface pings from host but not from namespace

  - by jtlebi

  My setup: Private network vboxnet1 10.0.7.0/24 1 Host, ubuntu desktop 1 VM, ubuntu server (VirtualBox) Adressing layout: HOST: 10.0.7.1 VM: 10.0.7.101 VM MAC NAMESPACE: 10.0.7.102 On the VM, I ran the following commands: ip netns add mac # create a new nmespace ip link add link eth0 mac0 type macvlan # create a new macvlan interface ip link set mac0 netns mac On the mac namespace, inside the VM: ip link set lo up ip link set mac up ip addr add 10.0.7.102/24 dev mac0 So that we basically end up with: (Like Inception ?) +------------------------+ | Host: 10.0.7.1 | | | | +--------------------+ | | | VM: 10.0.7.101 | | | | | | | | +----------------+ | | | | | NS: 10.0.7.102 | | | | | | | | | | | +----------------+ | | | +--------------------+ | +------------------------+ What works: Ping between Host and VM Ping between NS and NS dhclient from NS What does not work: ping between NS and VM ping between NS and Host Where I started to go nuts: tcpdump on host (the real machine) actually shows ARP request AND replies tcpdump on NS shows ARP requests sent to the host tcpdump on VM makes the whole mess work (!) -- ping starts to get answers when tcpdump is started on the VM ?!? So, I bet you were eager for it, my question is: how to I make it work ? I suspect something's wrong with ARP on the macvlan inside the NS but can't figure out what exactly... Btw, I did the same expérimentations with the mac0 interface directly on the VM (no namespace) and it worked flawlessly.

  Read the article

• WAN Optimization for Small Office/Home Office

  - by TiernanO

  I have been reading up on WAN optimization for the last while, mostly out of interest of speeding up my own internet connections, but also to speed up the office internet connection. At home, I have 2 cable modems plugged into a RouterBoard RB750, which load balances the connections. In the office, we have a single connection into a NetGear router. Most of the WAN Optimization products I have seen, seem to be prohibitively expensive, but also seem to be based on the idea of having multiple branches around the world. What I am looking for, ideally, is as follows: software install: I am "guessing" I need to install it in 2 places: one in the office or house, and one in "the cloud". any connections going to, say, The US (we are in Europe, but our backup's live in the US currently, which would be something important to speed up) would be "tunnelled" though the Optimizer. If downloading or uploading large files, open multiple connections between both "the cloud" and the optimizer... This is where a lot of speed could be gained. finally, for items not compressed, they would be compressed on the cloud side of things, also items that are already on the optimizer could be not sent again. kind of like RSync or Proxy servers... So, is there something that can be done? Is it available using off the shelf components (some magic script with SSH, Squid, Linux and duct tape) or is it something that needs to be purchased? or even an Open Source Project that does 90% of what i am asking?

  Read the article

• How do I send e-mails with attachments to a Microsoft WebTV user?

  - by Petr 'PePa' Pavel

  my friend uses Microsoft WebTV (e-mail address ends with @webtv.net) and I'd like to send him an e-mail with a picture attached to it. We went through a series of attempts one of which ended up a success, all others a failure. He just can't see my e-mail in his mailbox, when it contains an attachment. E-mails without attachments always go through all right. What seemed to help in the first successful case, was that he added my e-mail address to his address book and my e-mail suddenly showed up. Seemed to have been delivered before but hidden. He kept my address in his address book however, it didn't help with the following trials. He did look into his junk folder, nothing there. I made sure the file name contains no spaces. It's a regular jpeg, named something-like-this.jpg I downsized it to have only about 50k, as I've read somewhere that that's a limit. I actually doubt this piece of information, because I think the successful attempt was larger. webtv.net contains zero information. I watched their video demo for the e-mail client, so I at least know how the user interface looks like. I've never laid my hands on the real thing. I'm an advanced user myself (a programmer) but I can't wrap my mind around this. He on the other hand, is a very technically inexperienced user and because he's half way across the globe, I can't come and look over his shoulder. He doesn't have a computer, afaik there's no way I could see what he sees. Any ideas on how to debug this? Thanks for your time, guys. P.S. I can't tag this "webtv" because such tag doesn't exist yet and my reputation is too low, sorry.

  Read the article

• Why am I missing 4GB of RAM on Windows Server 2008 R2 64bit?

  - by Nick G

  I noticed today that a server was very low on memory. It physically has 8GB installed and runs Windows 2008 R2 Standard 64bit. It also hosts 2 virtual machines using HyperV. Server is Dell Poweredge R510. However the host OS reports in task manager that it only has 4GB of RAM, despite actually having 8GB and it being a 64bit OS. Computer properties shows Installed memory: 8.00GB (3.99GB usuable). Why would "usable" be half the real RAM installed under a 64bit OS? Additionally nearly all of the 4GB of visible RAM on the host OS is being used by something without anything showing up in task manager (presumably HyperV as it's allocated 3.6GB to the virtual machines its hosting). However that doesn't explain where the other 4GB has gone which Windows can't even see. Where is my missing 4GB of RAM? Update: Dell OpenManage says this: Total Installed Capacity 8192 MB Total Installed Capacity Available to the OS 4096 MB So looks like Nathan's suggestion of memory mirroring might be correct. I'll have to reboot to check this (I think?) Update 2 OK. So I reboot and I get a message saying "the amount of system memory has changed" (despite not having touched the hardware in a year). Once Windows has booted, all 8GB is visible again. Looks like I probably have a hardware RAM issue (I'll perhaps try reseating it whenever I can chuck everyone off the server next). Thanks for your answers and comments. I was hoping it was going to be the mirrored-RAM option but it seems not - that's not even mentioned in the BIOS.

  Read the article

• Loadbalancing with nginx and tomcat

  - by London

  Hello this should be fairly easy to answer for any system admin, the problem is that I'm not server admin but I have to complete this task, I'm very close but still not managing to do it. Here is what I mean, I have two tomcat instance running on machine1 and machine2. People usually access those by visiting urls : http://machine1:8080/appName http://machine2:9090/appName The problem is when I setup nginx with domain name i.e domain.com, nginx sends requests to http://machine1:8080/ and http://machine2:9090/ instead of http://machine1:8080/ and http://machine2:9090/appName Here is my configuration (very basic as it can be noted) : upstream backend { server machine1:8080; server machine2:9090; } server { listen 80; server_name www.mydomain.com mydomain.com; location / { # needed to forward user's IP address to rails proxy_set_header X-Real-IP $remote_addr; # needed for HTTPS proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_set_header Host $http_host; proxy_redirect off; proxy_max_temp_file_size 0; proxy_pass http://backend; } #end location } #end server What changes must I do to do the following : - when user visits mydomain.com - transfer him to either machine1:8080/appName or machine2:9090 Thank you

  Read the article

• DVI output only working on Windows, not during booting or on Linux

  - by Mononofu

  So yesterday I booted my laptop up and the external monitor I have it connected to just stayed black. At first, I thought the problem would go away when Ubuntu was loaded, but it didn't. I tried to reboot a few times, to no avail. Then I decided to give Windows 7 a try, and suddenly (at the login-screen), my external monitor turned on and worked like normal. I have connected the monitor via DVI, and this only seems to work with Windows now. I don't even get a signal in my BIOS! Mind you, everything was working fine before that, and I didn't change a single thing. I then tried to connect the monitor via VGA (from my DVI jack, which can output VGA using an adaptor), and it worked again. However, 1920x1200 using VGA looks like crap - black print on white background is basically illegible. Do you have any ideas how to fix this peculiar problem? I only use windows for gaming, so it's no real help that it still works normally. Please also excuse any spelling mistakes, I am practically typing this blindly. Edit: I only have one graphics card in my laptop, and I can't select anything related to that in my BIOS. In fact, I can pretty much do almost nothing there. My laptop is a Nexoc Osiris E703, graphics gard is a GeForce Go 7900 GTX. As I mentioned before, DVI output during booting and on Ubuntu was working fine for years before yesterday!

  Read the article

• torrent downloads not showing on Squid log

  - by noobroot

  hello, i have just a few months working as sysadmin, hence i still have lots to learn, first thing id like to do is as follows: We have an OpenBSD 4.5 box acting like firewall,dns,cache etc, the box has 2 network cards, one conected directly to the internet and the other to our switch, i used to work with sarg for the log analysis but then changed to the much faster free-sa. I use a daily free-sa report to check the bandwidth usage and report our top 5 bandwidth consumers (3 days a week being #1 and you will be buying the pizzas :D, we are a small company ~20 so we are very familiar). this was working really good until recently, one of us required to download some stuff via torrent (~3GB) and since the pizza rule is active for non-work related downloads, he told me (verified) that his download was indeed work related so i would dismiss that 3GB off his quota, but to my surprise the log didnt showed that 3GB, since his ip consumption was only around 290MB. More recently, since the FIFA world cup started, we know that some of the employees are watching the match's streaming, we know it and we dont care about it since, like already stated, we are a small company so we dont have restrictive policies, we all can chat, watch youtube, download anything we want BUT we are only allowed 300MB a day otherwise you'll get in the top5-pizza-board, anyway, that streaming consumption is also not showing in the free-sa reports. So my question is, why is these data being excluded from the reports? im thinking that the free-sa reports list only certain types of things but im also thinking if are the squid logs the ones that are not erm... logging these conections. Any help, guide, advice or clarification is appreciated.

  Read the article

• Slow manipulation of netfilter rules

  - by Ole Martin Eide

  I have a script maintaining gre tunnels and firewall rules using the "ip" and "iptables" tools. Setting up hundreds of tunnels, and adresses per interface runs just fine. Takes less than 0.1 second per interface, however when I get around to do the firewall rules everything slows down spending 0.5 per insertion. Why is it running so slow? What can I do to improve the speed? It seems like I could try ipset instead, but I really feel there is something wrong with the kernel or something. The interesting thing is that the first 10 rules runs fast, then it slows down.. mybox(root) foo# iptables -V iptables v1.3.5 mybox(root) foo# uname -a Linux foo 2.6.18-164.el5 #1 SMP Tue Aug 18 15:51:48 EDT 2009 x86_64 x86_64 x86_64 GNU/Linux mybox(root) foo# cat test.sh #!/bin/sh for n in {1..100} do /sbin/iptables -A OUTPUT -s ${n} -j ACCEPT /sbin/iptables -D OUTPUT -s ${n} -j ACCEPT done mybox(root) foo# time ./test.sh real 1m38.839s user 0m0.100s sys 1m38.724s Appriciate any help. Cheers!

  Read the article

• Recommended drive encryption solution

  - by Chris Driver

  Hello, I will soon be purchasing a number of laptops running Windows 7 for our mobile staff. Due to the nature of our business I will need drive encryption. Windows BitLocker seems the obvious choice, but it looks like I need to purchase either Windows 7 Enterprise or Ultimate editions to get it. Can anyone offer suggestions on the best course of action: a) Use BitLocker, bite the bullet and pay to upgrade to Enterprise/Ultimate b) Pay for another 3rd party drive encryption product that is cheaper (suggestions appreciated) c) Use a free drive encryption product such as TrueCrypt Ideally I am also interested in 'real world' experience from people who are using drive encryption software and any pitfalls to look out for. Many thanks in advance... UPDATE Decided to go with TrueCrypt for the following reasons: a) The product has a good track record b) I am not managing a large quantity of laptops so integration with Active Directory, Management consoles etc is not a huge benefit c) Although eks did make a good point about Evil Maid (EM) attacks, our data is not that desirable to consider it a major factor d) The cost (free) is a big plus but not the primary motivator The next problem I face is imaging (Acronis/Ghost/..) encrypted drives will not work unless I perform sector-by-sector imaging. That means an 80Gb encrypted partition creates an 80Gb image file :(

  Read the article

• Microsoft Excel not graphing

  - by SmartLemon

  Im not sure if this is a math question or a su question. The experiment was relating the period of one "bounce" when you hang a weight on a spring and let it bounce. I have this data here, one being mass and one being time. The time is an average of 5 trials, each one being and average of 20 bounces, to minimize human error. t 0.3049s 0.3982s 0.4838s 0.5572s 0.6219s 0.6804s 0.7362s 0.7811s 0.8328s 0.869s The mass is the mass that was used in each trial (they aren't going up in exact differences because each weight has a slight difference, nothing is perfect in the real world) m 50.59g 100.43g 150.25g 200.19g 250.89g 301.16g 351.28g 400.79g 450.43g 499.71g My problem is that I need to find the relationship between them, I know m = (k/4PI^2)*T^2 so I can work out k like that but we need to graph it. I can assume that the relationship is a sqrt relation, not sure on that one. But it appears to be the reverse of a square. Should it be 1/x^2 then? Either way my problem is still present, I have tried 1/x, 1/x^2, sqrt, x^2, none of them produce a straight line. The problem for SU is that when I go to graph the data on Excel I set the y axis data (which is the weights) and then when I go to set the x axis (which is the time) it just replaces the y axis with what I want to be the x axis, this is only happening when I have the sqrt of "m" as the y axis and I try to set the x axis as the time. The problem of math is that, am I even using the right thing? To get a straight line it would need to be x = y^1/2 right? I thought I was doing the right thing, it is what we were told to do. I'm just not getting anything that looks right.

  Read the article

• Nginx load balancing and maintaining URLs

  - by Steve Klabnik

  I'm trying to use nginx as a load balancer, and it's working great. One problem, though. The load balancing box is at 123.123.123.123, and the backend box is 456.456.456.456. So I have this config: upstream backend { server 456.456.456.456; } server { listen 80; server_name 123.123.123.123; access_log off; error_log off; location / { proxy_set_header Host $host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_pass http://backend; } } This works great. I hit 123.123.123.123 in my browser, and the page comes up. But now the URL in the browser says http://456.456.456.456. Do I need to use a rewrite rule or something to keep the url correct? I don't want it to be different when going to different backed servers. None of the tutorials I've read have mentioned anything about this.

  Read the article

• What does Firefox do when "scanning for viruses" after download?

  - by Joey

  Never mind the fact that Firefox is a browser and not a AV tool, but what exactly does it do after a download? Even on systems that have an up-to-date AV this generates a pause of several seconds after download (where I can't open the file from within the DL manager) and I have no idea what FF might be trying there. I know I can turn it off (using FF only at work anyway) but I'm wondering. I can think of some things here what it might be: FF itself is a AV scanner and it loads signatures in the background and whatnot. Sounds highly unlikely and shouldn't need tens of seconds for 20 KiB files. FF tries to talk with the installed AV to munch the file. Sounds unneeded, given that most AV programs feature real-time protection anyway and therefore will have caught a virus already and also because FF does that on systems without AV installed too. FF uploads the file to some online virus checker. Unlikely and stupid. FF instructs some online virus checker to download the file and check it. Unlikely and would be a nice target for DoSing that service. FF generates a hash of the file and sends that somewhere (presumably Google) to check for. They then respond with either "Whoa, that hash is totally a virus" or "Nope, that MD5 doesn't look very virus-y to me". I'm running out of better ideas. Anyone have a clue?

  Read the article

• Cisco configuration for public library internet

  - by AlternateZ

  I'm a C/C++ computer programmer turned IT support guy working for a public library. My day is usually spent helping random grandparents learn how to use email, so my networking knowledge is limited to what I can glean from google. Here's the situation. We have a public library with 20 PCs on a LAN and also public wifi access. Previously we were running all of this on 1 ADSL connection and people complained about low speeds. We hired a networking company to set up a Cisco dual-WAN router for us, and purchased an additional ADSL connection. The intention was to give the LAN PCs a guaranteed amount of bandwidth each, and then let the wifi users split the rest. The results were far worse than what we expected, and all we got from the company was excuses and they've since washed their hands of us. During busy periods, net performance on the LAN PCs are so poor that attaching files to gmail etc often times out and fails - far from the "guaranteed amount of bandwidth each" that we hope for! Sometimes it feels like performance is worse than before when we had 1 ADSL link and an unconfigured router? Anyways, surely this is a problem encountered a million times over across the world? (Sharing internet across many users effectively.) What are standard solutions for something like this? I admit to not even knowing the right jargon to google for (load balancing?) I'd appreciate any links to resources/guides that might help me get a better understanding of the problem/solutions, and perhaps some stories of your own experience in solving similar problems. This will help us evaluate and negotiate with network consultants in the future. If its relevant, our router config contains a section "policy-map" with "bandwidth percent" for each class of user (LAN, wifi), and "fair queue".

  Read the article

< Previous Page | 562 563 564 565 566 567 568 569 570 571 572 573  | Next Page >