Search Results

Search found 17782 results on 712 pages for 'questions and answers'.

Page 568/712 | < Previous Page | 564 565 566 567 568 569 570 571 572 573 574 575  | Next Page >

• Why does my ftp(e)s server fails like half of the time

  - by user1092608

  I have this discussion at work regarding our ftp server running via vsftpd. Initially, we have opted to serve ftpes instead of sftp because this seemed the most flexible and straightforward solution for our server to have secure file transmission. Afterwards, our ftp server seems to be a source of issues for our end users. Half of the time, users complain about not working ftp connections. I must say, i tested our FTP trough different infrastructures (=in the field, at random times at random places) and indeed, sometimes behind some configurations (=no idea how they are configured, because the 'field' testing), i recieve errors. Some of the are: Error: Failed to retrieve directory listing (filezilla) Furthermore, behind my basic home configuration, everything seems to be running fine. I (think I) did all the basic configuration checks (passive mode?, firewall for all ports?, ...) and can't seem to find the source. Being a bunch of techies at our small office, yet knowing nothing about infrastructure, some start suggesting that ftps protocol could be the source of issues. ("No, i only knew sftp so far" "Ftps is not widespread"). I, however, strongly doubt this hypothesis, since reading around on the www, asking questions on serverfault, everyone seems to deny this. So, as I would like to avoid reconfiguring, since this involves messing around in our SSH service, our virtual user setup and ftp service, i would need some advice on 1) what could be potentially the general cause? 2) do you have some general tips? 3) would you mind having a look at my configuration file? ----- General Settings ----- write_enable=YES dirmessage_enable=YES nopriv_user=ftpsecure ftpd_banner="Welcome to XXXX FTP!" hide_ids=YES hide_file=.* max_per_ip=10 max_clients=10 local_enable=YES local_umask=022 chroot_local_user=YES secure_chroot_dir=/usr/share/empty userlist_enable=NO userlist_deny=YES userlist_file=/etc/vsftp_deny_users guest_enable=YES guest_username=ftpvirtual virtual_use_local_privs=YES user_sub_token=$USER local_root=/srv/ftp/ftpvirtual/$USER anonymous_enable=NO syslog_enable=NO xferlog_enable=YES xferlog_file=/var/log/vsftpd_xfer.log connect_from_port_20=YES pam_service_name=vsftpd listen=YES listen_port=21 pasv_enable=YES pasv_min_port=30000 pasv_max_port=30030 pasv_address=foo ssl_enable=YES rsa_cert_file=/etc/vsftpd.pem rsa_private_key_file=/etc/vsftpd.pem force_local_data_ssl=YES force_local_logins_ssl=YES ssl_tlsv1=YES ssl_sslv2=YES ssl_sslv3=YES ssl_ciphers=HIGH anon_mkdir_write_enable=NO anon_root=/srv/ftp anon_upload_enable=NO idle_session_timeout=900 log_ftp_protocol=NO dsa_cert_file=/etc/vsftpd.pem Thanks

  Read the article

• SSH & SFTP: Should I assign one port to each user to facilitate bandwidth monitoring?

  - by BertS

  There is no easy way to track real-time per-user bandwidth usage for SSH and SFTP. I think assigning one port to each user may help. Idea of implementation Use case Bob, with UID 1001, shall connect on port 31001. Alice, with UID 1002, shall connect on port 31002. John, with UID 1003, shall connect on port 31003. (I do not want to lauch several sshd instances as proposed in question 247291.) 1. Setup for SFTP: In /etc/ssh/sshd_config: Port 31001 Port 31002 Port 31003 Subsystem sftp /usr/bin/sftp-wrapper.sh The file sftp-wrapper.sh starts the sftp server only if the port is the correct one: #!/bin/sh mandatory_port=3`id -u` current_port=`echo $SSH_CONNECTION | awk '{print $4}'` if [ $mandatory_port -eq $current_port ] then exec /usr/lib/openssh/sftp-server fi 2. Additional setup for SSH: A few lines in /etc/profile prevents the user from connecting on the wrong port: if [ -n "$SSH_CONNECTION" ] then mandatory_port=3`id -u` current_port=`echo $SSH_CONNECTION | awk '{print $4}'` if [ $mandatory_port -ne $current_port ] then echo "Please connect on port $mandatory_port." exit 1 fi fi Benefits Now it should be easy to monitor per-user bandwidth usage. A Rrdtool-based application could produce charts like this: I know this won't be a perfect calculation of the bandwidth usage: for example, if somebody launches a bruteforce attack on port 31001, there will be a lot of traffic on this port although not from Bob. But this is not a problem to me: I do not need an exact computation of per-user bandwidth usage, but an indicator that is approximately correct in standard situations. Questions Is the idea of assigning one port for each user is a good one? Is the proposed setup an reliable one? If I have to open dozens of ports for many users, should I expect a performance drawback? Do you know a rrdtool-based application which could make the chart above?

  Read the article

• Windows 7 pc freezes for an indeterminate amount of time after unlocking

  - by pikes

  Not sure if this type of question is appropriate for this forum, but I've tried everything I can think of to solve this problem aside from format/reinstall. I recently got a new work PC (Dell optiplex 755) with windows 7 professional x64. Standard developer software installed for .net development: VS2008, VS2005, SQL management studio, office 2007, etc. Recently I've been having this weird problem where after I lock my pc, when I try to unlock it, the screen will be black for awhile after unlocking. I can ctl+alt+del and put my password in but then it just goes black. The amount of time on the black screen seems to be related to the amount of time I am away from my PC. If only away a few minutes, it'll take about a minute to get to the desktop. If away for an hour, could take up to 15 minutes. If I lock it and go home for the night, I have to restart my PC in the morning (I've let it sit for an hour after a night of being locked and nothing happened). It doesn't do it every time but definitely the majority of the time. One weird thing I've seen is that if I remote into my machine before trying to log back in it does not do it. I uninstalled all software back to the point when I remember it started happening and it still does it. I was using this PC for a few weeks without this problem happening at all. Anyone know what my next troubleshooting steps could be? My IT department tried to fix it by moving my old profile to another disk and having me log in, effectively recreating a profile from scratch but that didn't solve it. As I said above if this isn't the right forum for these types of questions please let me know. Thanks in advance!

  Read the article

• Searching for just files

  - by M Schenkel

  I have a couple questions about searching for files on Windows 7. I find the XP method much easier than this new Windows 7 search. Note: I am only concerned about finding files matching a search term, not ALL files containing the search term. Is there a way to search just for files? When I use the search it seems to be searching "within" files and returning instances where the name of the file is used. Example: I have a whole web directory and want to find the javascript files. But if I enter "myjavascript.js" in the search, it also returns all the html files which reference the javascript file. This is both slow and difficult to actually find the reference to the file. Is there a way to search for an exact match? The search seems to implicitly use wildcards. For instance, say I have a bunch of files in a folder: file1.txt,file11.txt, file12.txt, file13.txt. If I enter "file1.txt" in the searcher it returns instances as if I were using a wild card file1*.txt I miss XP!!!!

  Read the article

• How to get Subversion repository from svn:// and https://?

  - by Hikari

  I know these are noob questions, but I never got my own Subversion running before and I'm kinda lost. I installed VisualSVN in Windows, but it doesn't support svn:// protocol by default, only HTTP or HTTPS. It is working fine over HTTP, and I'm able to manage it from its management tool, see its repositories and get their HTTP-based URL, and from that I'm able to use Tortoise to check out and check in. I'm able to check out from a repository URL using Tortoise: http://Main:90/svn/HikariKrumo/ But I need svn:// protocol for Redmine to access it. Redmine says to support http:// but it reports this error message: The entry or revision was not found in the repository.. And I need HTTPS to access it from Internet. If I can get Redmine to access it from svn:// I can just configure it to use HTTPS in place of HTTP, and I hope it all to works. I like VisualSVN because of its management tool, but I can use another Subversion distro if needed, as long as it supports svn:// and https://. I'm getting crazy on it because it should be simple but I can't get it to work.

  Read the article

• Connecting PC to TV via HDMI/DVI: Windows XP doesn't allow the appropriate screen resolution

  - by Jørgen

  I have a computer that is connected to the living room TV (a Panasonic) via HDMI. There is no other monitor connected. My problem is that the computer, which is running Windows XP, does not allow me to set the proper resolution for the TV. Both the graphics adapter and the TV should support the 1280x720 resolution, but it cannot be selected - the only available options are 1280x600 and 800x600, both in the "native" Windows dialog box and the custom Intel graphics options dialog box. Do anyone have a suggestion for a solution for this? Things I've thought of: Setting the resolution directly in the registry (where?) Installing some "custom" monitor driver (the TV manufacturer does not appear to provide any, currently the "generic" one is used) Details on the setup: Connection: DVI output on the computer via a passive DVI-HDMI adapter to the HDMI input on the TV, audio is run on a separate link, the TV is able to combine video and audio without any problem, the problem is there regardless of whether or not the audio is connected. The connection is several meters long through some walls, for this reason using a VGA cable instead is not an option. Note that the report explicitly says that the TV supports 1280x720. Still, I am not allowed to select it in Graphics Options, only 1280x600 and 800x600 is available. For 800x600, there's a lot of black around the edges; for 1280x600, the screen is "zoomed" so the edges of the monitor image (like the taskbar) is not visible. Other: The computer is running Windows XP. More recent versions of Windows are not an option (I have no licence). Linux is probably not an option (some of the video streaming sites I plan to use do not support it, I think) I wrote the rest of the details below. Thanks for any help!! TV: Panasonic TX-L32X10Y, European version; a 720p 32" quite "regular" LCD TV. Allowed resolutions according to manual: Signal name: 640x480 @60HZ Horizontal frequency: 31.47 kHz Vertical frequency: 60Hz Signal name: 750/720) /60p Horizontal frequency: 45.00 kHz Vertical frequency: 60Hz Signal name: 1,125 (1,080) / 60p Horizontal frequency: 67.50 kHz Vertical frequency: 60Hz (this is exactly how the manual presents it. PC via D-SUB (VGA cable) and "regular" HDMI have more alternatives.) Messing with the "zoom" settings on the TV does not affect the available resolution options on the computer. Computer: The following is a printout from one of the graphics adapter option pages. I think it covers most of it. The computer is a Dell. INTEL(R) EXTREME GRAPHICS 2 REPORT Report Date: 04/17/2011 Report Time[hr:mm:ss]: 20:18:02 Driver Version: 6.14.10.4396 Operating System: Windows XP* Professional, Service Pack 3 (5.1.2600) Default Language: English DirectX* Version: 9.0 Physical Memory: 1021 MB Minimum Graphics Memory: 1 MB Maximum Graphics Memory: 96 MB Graphics Memory in Use: 6 MB Processor: x86 Processor Speed: 2593 MHZ Vendor ID: 8086 Device ID: 2572 Device Revision: 02 * Accelerator Information * Accelerator in Use: Intel(R) 82865G Graphics Controller Video BIOS: 2972 Current Graphics Mode: 1280 by 600 True Color (60 Hz) * Devices Connected to the Graphics Accelerator * Active Digital Displays: 1 * Digital Display * Monitor Name: Plug and Play Monitor Display Type: Digital Gamma Value: 2.20 DDC2 Protocol: Supported Maximum Image Size: Horizontal: Not Available Vertical: Not Available Monitor Supported Modes: 1280 by 720 (50 Hz) 1280 by 720 (60 Hz) Display Power Management Support: Standby Mode: Not Supported Suspend Mode: Not Supported Active Off Mode: Not Supported (disclaimer: this question was also asked at the Wikipedia Reference Desk some time ago and might show up in a Google search. I got no useful answers there.)

  Read the article

• Virtual Server HDD shrinks without apparent reason

  - by Christian

  We have a virtual hosted Linux server, and in the last few months every now and then the HDD shrinks from 400GB down to the exact byte count that is in use. All existing data can be downloaded and displayed without a problem, but we can't upload or edit any files because of the "full" hard drive. Here is a screenshot, where "size" should be 400GB: This has happened twice before, and again today. The last times, when I reported the issue to the host, they said "that isn't possible, you must be doing it wrong", but soon after the call, the problem vanished without us doing anything, so I suppose that they have some kind of problem they're not willing to admit. Even after the fact, they acted like nothing was wrong and wrote me a mail in which they explained that I can use "df -h" to view available disk space (well duh, how do you think I noticed this particular issue?). Questions about if and what they had done were ignored. It has happened around the 25th to 28th of the month, so I suspect that they might have a cronjob running every 30 days or so which wreaks havoc with some VM configs. I just want to understand the problem, but the host support hasn't been very helpful in that regard. I have tried Googling the issue, but any combination of search terms I can come up with just gives me tutorials on how to change HDD size in a virtual machine. a) What could be the cause of shrinking HDD size in a Ubuntu 12.04.3 LTS server? Could there be anything in our virtual machine or is it more likely to be an issue with the vm host? b) Can I do anything about it without needing to contact the host's support? c) Is there anyway I can prevent this from happening at all?

  Read the article

• Huh? JDK not found? (on Windows 7 64-bit)

  - by Android Eve

  I am setting up a development environment for the latest Android 2.3 on a fresh install of Windows 7 64-bit. I first installed the 64-bit JDK 6 (jdk-6u23-windows-x64.exe). Then, I installed 64-bit Eclipse Classic 3.6 (eclipse-SDK-3.6.1-win32-x86_64.zip). Then, I proceed to install the Android SDK Starter Package: installer_r08-windows.exe. But... upon start it says: "Java SE Development Kit (JDK) not found." Why? I just installed it. Is this a mismatch between 32-bit and 64-bit? How do I solve this? Update (1): I tried setting the %JAVA_HOME% environment variable, as well as setting the Installed JREs in Eclipse, as suggested below. None of these solved the problem. It appears that I am not the only experiencing the problem, as this thread suggests: http://stackoverflow.com/questions/1919340/android-sdk-setup-under-windows-7-pro-64-bit I wonder whether there is a 64-bit version of the Android SDK. Update (2): I used the zip version instead (android-sdk_r08-windows.zip), ran android.bat, updated all SDK packages, and installed the ADT plugin (8.0.1), not before having to check: 'Contact all update sites during install to find required software'. We'll see how this goes... Update (3): It worked! (going to accept @bubu's answer shortly) -- but why doesn't the emulator include the HelloAndroid app when I run it (Ctrl+F11) from Eclipse?

  Read the article

• Can't login after upgrading to Windows 8.1

  - by flatline

  This afternoon, I upgraded my work laptop from Windows 8 to Windows 8.1. I had previously had a local account, but after the upgrade, it prompted me to enter my windows account credentials, which I had set up beforehand at some point. I entered my password and clicked next, went through another screen or two, grew tired with the process, and clicked whatever the equivalent button to "skip this step" that I was presented with. Now I can't log in. Not with my (previous) local account password, and not with my windows account password. It's a Dell with biometric identification, which I had set up previously, so I put my finger on the reader and it complained that I couldn't use that fingerprint because I had changed my password. But, I hadn't wittingly changed my password at all. I assume that what happened is that, by entering my credentials, my local account was tied to the Windows account, but because I cancelled the process partway through, something went wrong and I cannot log in. A few questions: 1) How do I log in with my windows account credentials? Should LOCALMACHINENAME\username, which was my previous login method, still work for the Windows account? When I booted to safemode it prompted me with WindowsAccount\myemailaddress, which allowed me to login there, but the regular login doesn't accept the '@' symbol. 2) Is there any way to make that account local-only again? I can't find any way of doing it. 3) I managed to enable the local administrator account and get back into the box; failing all else, is there a quick way to migrate my old profile over to a new user?

  Read the article

• Force Installing a Radeon HD 2100 on Windows 8

  - by Click Ok

  I'm trying force installing a Radeon HD 2100 on Windows 8. I've found that link from AMD with the drivers for Windows7: http://support.amd.com/us/gpudownload/windows/legacy/Pages/legacy-radeonaiw-vista64.aspx I know too that AMD will stop support Radeon HD 400 and older: http://www.techspot.com/news/48321-amd-drops-windows-8-support-for-radeon-hd-4000-and-older.html Now, let's go to the problem. If I try install the 12.6 driver, Windows will stick with the "basic display adapter", and this is bad for 3d games like Minecraft, that runs really slow now compared with the previous Windows7 installation. Forcing install the catalyst driver can help to fix it. So, I follow that steps: Extract the Catalist Driver (C:\AMD\Support\12-6-legacy_vista_win7_64_dd_ccc_whql) Right click the "basic display adapter" on device manager, and "update driver" Search on PC I will choose the driver "With Disk" "C:\AMD\Support\12-6-legacy_vista_win7_64_dd_ccc_whql\Packages\Drivers\Display\W76A_INF" There is a big list of drivers and the nearest driver to HD 2100 is "Radeon HD 2350 Series" My questions: Why isn't "Radeon HD 2100 Series" listed? (or Where is it listed?) In theory it must be listed" The first link above show that "This article applies to the following configuration(s):" (...) "AMD Radeon HD 2000 Series" Am I doing something wrong?

  Read the article

• Exchange 2003 mail non-delivery (NDR), spam activity? events 7002 & 7004

  - by HighTechGeek

  Windows Server 2003 Small Business Server SP2 Exchange Version 6.5 (Build 7638.2: Service Pack 2) This network has been neglected and has been having email problems for years and was on many blacklists. I was called in after the server eventually crashed... I got the server back up and running, but email problems persist. Outgoing mail delivery is sporadic. Sometimes the mail goes through, sometimes a delayed delivery report is generated after a day or more, and sometimes it seems to go through, but the recipient never receives it. Not sure if spammers are successfully using the server as a relay (see event entries below after turning on maximum SMTP logging)... User PCs infected with viruses and server was blacklisted on many sites (I used mxtoolbox.com) I have cleaned all the PCs and changed all passwords (including administrator) I have requested removal from all of the blacklists - most have removed the listing, some take more time. I have setup rDNS pointer records with the ISP (Comcast) - that was one reason for some of the blacklistings. I have tested that it's not an open relay using telnet as described here: www.amset.info/exchange/smtp-openrelay.asp I followed the advise of a Spamhaus & Microsoft article to enable maximum SMTP logging. http://www.spamhaus.org/faq/answers.lasso?section=isp%20spam%20issues#320 which directed me to Microsoft KB article 895853, specifically, the part 2/3 down titled: "If mail relay occurs from an account on an Exchange computer that is not configured as an open relay" . The Application Event Log is filling with this type of activity (Event ID 7002, 7002 & 3018 errors): Event Type: Error Event Source: MSExchangeTransport Event Category: SMTP Protocol Event ID: 7004 Date: 1/18/2011 Time: 7:33:29 AM User: N/A Computer: SERVER Description: This is an SMTP protocol error log for virtual server ID 1, connection #621. The remote host "212.52.84.180", responded to the SMTP command "rcpt" with "550 #5.1.0 Address rejected [email protected] ". The full command sent was "RCPT TO: ". This will probably cause the connection to fail. and this: Event Type: Warning Event Source: MSExchangeTransport Event Category: SMTP Protocol Event ID: 7002 Date: 1/18/2011 Time: 7:33:29 AM User: N/A Computer: SERVER Description: This is an SMTP protocol warning log for virtual server ID 1, connection #620. The remote host "212.52.84.170", responded to the SMTP command "rcpt" with "452 Too many recipients received this hour ". The full command sent was "RCPT TO: ". This may cause the connection to fail. or a variant of: Event Type: Warning Event Source: MSExchangeTransport Event Category: SMTP Protocol Event ID: 7002 Date: 1/18/2011 Time: 8:39:21 AM User: N/A Computer: SERVER Description: This is an SMTP protocol warning log for virtual server ID 1, connection #661. The remote host "82.57.200.133", responded to the SMTP command "rcpt" with "421 Service not available - too busy ". The full command sent was "RCPT TO: ". This may cause the connection to fail. also Event Type: Error Event Source: MSExchangeTransport Event Category: NDR Event ID: 3018 Date: 1/18/2011 Time: 9:49:37 AM User: N/A Computer: SERVER Description: A non-delivery report with a status code of 5.4.0 was generated for recipient rfc822;[email protected] (Message-ID ). Causes: This message indicates a DNS problem or an IP address configuration problem Solution: Check the DNS using nslookup or dnsq. Verify the IP address is in IPv4 literal format. Data: 0000: ef 02 04 c0 ï..À Any guidance and/or suggestions and/or tests to perform would be greatly appreciated.

  Read the article

• Duplicate forwarded messages in Blackberry when using BIS

  - by Avery Payne

  Our Setup External email arrives at a Postfix server, is scanned, and then forwarded via settings in transport (using the RELAY:[{ip-address}] for a given address) to an Exchange 2007 server. Some users are on Exchange, but a few are still on the Postfix server (they will be moved in the near future). IMAPS is provided for external connections via Dovecot; in-house, IMAP is provided for the Gateway and native MAPI is used for Exchange/Outlook. Blackberries are connected via BIS, which uses Dovecot as a reverse-proxy IMAPS service to connect to Exchange (when the mailbox exists on Exchange, otherwise it connects to the mailbox on the gateway). The Issue We have a user that, when they forward an email on their Outlook client, they get a duplicate of the original message on their Blackberry. When I say duplicate, I mean that they have a copy of the forwarded version of the message (i.e. their version of the message that they obtained hitting the forward button), and a copy of the original message that shows up at the same time. The expected behavior is to just see the forwarded message, not the forwarded message and a 2nd copy of the original message. We've only seen this with Outlook users that also have a Blackberry. Other IMAP clients, such as OS X Mail or Thunderbird, do not exhibit this behavior when connecting to the Exchange server; forwarded messages work as expected. The Questions what is causing this to happen? why does it only affect Outlook/Blackberry setups, and not TBird/Blackberry or OSX-Mail/Blackberry? how do we get it to stop, before people go insane and never forward messages again?

  Read the article

• 4GB Memory Upgrade for Acer Aspire 5102WLMi

  - by Richard Slater

  I have bought a 4GB memory upgrade (2x 2GB PC2-5300 SODIMM) for my Acer Aspire 5102WLMi (Aspire 5100 Series) laptop, I installed the two memory modules correctly however with 4GB installed the laptop refuses to POST. I have tried the following: Tried both 2GB SODIMMs without the other (Worked Fine) Tried the original 512MB SODIMMs (Worked Fine) Tried with original 512MB SODIMM and new 2GB SODIMM (Worked Fine) Tried swapping over the 2GB SODIMs (Didn't Boot) Left the computer for 10 minutes with both 2GB SODIMMs installed (Didn't Boot) Checked latest BIOS installed (No Change) The Crucial website said that the laptop supported 4GB of RAM as do several other sites through found through Google, up until now I was fairly confident this would work. Couple of questions that would be good to have answered: Question: Has anyone got an Acer Aspire 5100 Series running with 4GB RAM? Answer: Yes, I have now got one working with 3.75GB Usable, the rest is occupied utilized by the Graphics Card. Question: Any tips on getting this to work; is there a CMOS reset switch? Answer: Yes there is, if both SODIMMs are removed two very small interlocking PCB tracks are revealed. If these are shorted together with a screwdriver the BIOS will be reset. Thanks.

  Read the article

• Problems in Table of Contents formatting

  - by ChrisW

  Two questions about captions in Word (they are related, hence the same post): Using Word 2010 (and its inbuilt equation editor) I've got figure captions which contain equations (well, actually, they represent chemical equations, such as nitrate, for which the correct representation is NO3- where the 3 is subscript and the - is superscript, but in the same column). However, when I generate a figure list, the equation displays as NO3- (with no subscript or superscript) - Word knows it's an equation though (the Equation Tools design ribbon/tab is displayed when I click on the NO3-). I've tried changing it from Professional to Linear and similar other obvious options, but still can't get it to display correctly. File to show this problem in action: http://dl.dropbox.com/u/101867759/EqtnTest.docx - note how the (chemical) equation for nitrate is rendered correctly in the 'caption' on Page 2, but not in the ToC on page 1. I have another caption where the whole figure is included in my list of figures. When I double click on the caption in my text, the caption is highlighted (as expected), but so is the figure (this doesn't happen with any of my other figures) so I assume that the figure has been 'linked' in some way to the text - how do I remove this link?

  Read the article

• How does everyone set up AWS for PHP with a git workflow while worrying about distributing EC2?

  - by Parris

  Hello, I have been looking for something like heroku but for php, and after much frustration (and almost finding what I need, but not quite) we decided to just go with AWS without any other abstraction. We are using PHP 5.3 (and CakePHP 1.3), and are currently using git. Ubuntu seems like the easiest way to get both of those on there and we will most likely use that. We aren't really going worry about outgoing email. We are using smtp through gmail, but will most likely switch to some other service eventually. I had 3 questions: 1) I have been looking at Zend Server, and I am not quite sure how that is more beneficial than xampp. Perhaps it is not? 2) I suppose to make the application scale we would need multiple instances of some ec2 ami. Then just duplicate it and such. The question then becomes how do we make sure all EC2 instances are up to date? 3) I understand the concept of load balancing to some degree. I understand that in 1 region you select a bunch of servers and have it load balance across them. The question then becomes well how about world wide? How do I make it so that traffic is directed to the correct ec2 server? I have heard of route 53, and tried signing up for that, but nothing appears in my control panel. Also perhaps it is just a DNS thing with my domain registrar? AHHH... some tutorial would be helpful!

  Read the article

• Grub Installation Failed: Fatal Error ... now what I do?

  - by eklavya

  I know there are some threads that touch this but I feel I have done something uniquely stupid. hence the post and plea for help. I am a beginner @ Linux. So I have a PC with a HDD (hard disk drive) and SSD (solid state drive) It was running Linux Mint /dev/sda1 - HDD Partition 1 - 2 TB (mounted this is /home /dev/sda2 - HDD Partition 2 - 1 TB (separate back up drive, i was backing up files to this) /dev/sdb1 - SSD Partition 1 - 100 GB (OS) /dev/sdb2 - SSD Partition 2 - 20 GB (Swap) The operating system was Linux Mint and was installed on the /dev/sdb1 i.e the solid state drive. I had partitioned off the sda into 2 TB and 1TB and presented the 2 TB as the /home to the OS. Anyway last night I decided to make a return to Ubuntu via the path of Elementary OS. Everything went fine with the install until it stated that GRUB installed failed and this was a Fatal error (no kidding I said). No I am stuck. I have definitely done something wrong and don't know what it is... My biggest pain is the files on the /dev/sda2. I want to save these before I try something drastic like wiping off the /dev/sda completely. So I have the following questions... Can I use a liveCD USB to save these files ? I can see the /dev/sda2 but was unable to access the files in the liveCD last not least ... how do I fix the main issue here. Why could the OS not install GRUB 2b... why is my SSD the /dev/sdb ... and not /dev/sda. Does that have something to do with it that my master boot record sits on the HDD /dev/sda and not /dev/sdb

  Read the article

• AMD processors witn graphics card bundled [closed]

  - by shybovycha

  Sorry for posting this question here - just don't know to which StackExchange website i should be writing. I've heard AMD created processors with video card bundled. So now these processors should work as fast as just usual processors with discrete video card but AMD's ones should use less power and spread less warm. Some googling around gave me the result like "AMD processors of A-series". They were mentioned to be build using that technology i described above. But on the other hand, we have a small rate of publishing and not-very-good quality of AMD drivers. I am a game-developer and web-developer so i need a powerful processor and graphics card and a lot of RAM on board (to make it possible to create a sample Grails application, for example or to create some 3D models in Maya/Cinema4D, for instance). Still i want my battery to be a long-living one, so power usage is a bit critical for me. So, my questions are: are there any processor building technology like i've described and which series they are (if they exist)? which processor shall fit the laptop the best: AMD one or i5/i7 on with nVidia graphics card for the purposes mentioned above?

  Read the article

• please explain these mongo statistics

  - by sivann

  My setup: I have 2 hosts, and 2 shards each. Host1 has 2 shards, and is the master of the replicas host2 has the secondaries of the 2 shards. . host1: shard1 (repset1),shard2 (repset2) host2: shard1 (repset1),shard2 (repset2) There's also a 3rd host that acts as arbitrer. I have 50 threads writing randomly to both shards (using a hash) via mongos with REPLICA_SAFE WriteConcern set on each insert. The questions: mongostat displays about 90% locked for both shards in host1 and about 1% locked on host2. Since I use REPLICA_SAFE which supposedly writes to both servers shouldn't the locks be the same? mongostat reports qr=30 for both shards of host1, and qw=0 always. Since I perform only writes how is this possible? Moreover on host2 all queues are reported 0. Faults are abut the same in all shards/hosts (arround 80). netIn/netOut on the secondaries (host2) are always about 200bytes/sec. Too low. mongos has 53 connections, host1's shards have 71 and 71 and host2's shards have 9 and 8. How is this? Please answer whatever you can. Thanks!

  Read the article

• Receiving and processing SMS messages through a script?

  - by ShankarG

  I am attempting to setup a system to receive and process SMS messages automatically. The system is intended for use in a context (an unfunded migrant workers' union in India) where both finances and sysadmin skills are extremely constrained (I would be the only person, in the near future, who would be administering the system). The intention is to make some functions - registration of members, generation of ID cards, communication of alerts and other information - easier. However, for receiving and sending SMS, I have not been able to find any email to SMS or other kind of gateway that functions in India. Perhaps there is one (edit: apparently Clickatell does have an India service, but the prices appear astronomical). If not, can one rely on a USB mobile modem (such as those provided by many mobile providers in India)? It seems like, with utilities such as gammu or bitpim, SMS operations on such a modem could be scripted. Is this actually feasible, though? Thanks in advance for your thoughts and suggestions. edit: Original first question removed since the two questions had little to do with each other. The original first question has been asked separately here

  Read the article

• Removed Old Domain Trust. Now Progress (9.1D) can't open DB File

  - by RLH

  My company has an old server, running Progress 9.1D on a Windows 2000 VM, which was used by our company OS (Vantage 6 by Epicor.) Vantage was our primary OS for a very long time. About 2 years ago, we migrated to a larger, corporate OS and we cancelled our service contract with Epicor. Yesterday, we removed an AD trust between the corporate domain and our old AD domain we used in the days of Vantage. After restarting the virtual server, I have been able to start the ProService for 9.1D Windows service, however, I can not get Vantage to start back up. When I run the application, I get the error in the message listed below. Transcript: ** Could not connect to server for database [progress db file], errno 0. (1432) How can I fix this? FYI, I haven't had to work with Progress in years and even then I wouldn't have considered myself a "novice"-- I'm even less knowledgeable than that title would suggest. Vantage had a lot of internal tools and I recall that Epicor support managed to prevent .pf scripts from being executed. If there was a Progress specific patch that needed to be applied, you had to do it within the Vantage software OR they had to remote into the machine to fix this. I may not be able to run a .pf script but I do know that I can log into the console-based server application. (Yes, I can't even recall which utility that was called. It is sad.) It's been a long time and I never had to digg into Progress that much. Please help and feel free to ask questions. If you need more info, I'll update this post.

  Read the article

• Specific issue on data pump API in oracle

  - by Median Hilal

  I have a client/server architecture. Using an Oracle dbms on the database server side. I need to perform a user-triggered (from client side) backup of the database, where the best way to perform that is using a stored procedure on the server side which the client may call, as the client has no oracle tools to perform the backup. I've searched thorough inside available solutions and have found that using a stored procedure is the best way. Well, then I found that using oracle data pump API is the best way to use inside a PL/SQl stored procedure. My specific questions about the API are... I would like to ask about two issues ... ---- The first ----- the detach function to detach the handler, is it necessary to be used at the end of the procedure? and what if I don't use it? I read the Oracle documentation but I didn't get their point, they say it doesn't terminate the job but indicates that the user is not interested in it, an when I use detach at the end of my procedure the exported .dmp file disappears. ---- The second ----- to perform a user (client side) triggered back up as the modification are only to the data, I used TABLE parameter for the export operation. But the version parameter... what should it be? I also read the documentation but couldn't determine what I need (LATEST or COMPATIBLE) ? Thanks

  Read the article

• How can I tell if my UPS is functioning properly or not for my PC?

  - by prabha

  For the last two days, my Uninterruptable Power Supply (UPS) has failed to produce the actual back up. So, I charged it for 24hrs and again checked that when the power failed my PC was automatically shut down. But in the time of power no supply from ups bt .......is my ups is working properly or not else there is direct power. It will cause any harm to my pc. my questions are..... Is the UPS functioning properly or not? If not, then will it harm my pc? If it is functioning, will it regulate direct power to pc without any cause? Is my UPS battery not working? What should I do to make my UPS batteries last for at least a year? I am using FRONTECH UPS 600va (Warranty for both ups and battery is expired) I already changed the battery 8 months previously. Note from editor: Tried to make as much sense of this question as I could. I hope I didn't alter the meaning in any way.

  Read the article

• Allow connections to only a specific URL via HTTPS with iptables, -m recent (potentially) and -m string (definitely)

  - by The Consumer

  Hello, Let's say that, for example, I want to allow connections only to subdomain.mydomain.com; I have it partially working, but it sometimes gets in a freaky loop with the client key exchange once the Client Hello is allowed. Ah, to make it even more annoying, it's a self-signed certificate, and the page requires authentication, and HTTPS is listening on a non-standard port... So the TCP/SSL Handshake experience will differ greatly for many users. Is -m recent the right route? Is there a more graceful method to allow the complete TCP stream once the string is seen? Here's what I have so far: #iptables -N SSL #iptables -A INPUT -i eth0 -p tcp -j SSL #iptables -A SSL -m recent --set -p tcp --syn --dport 400 #iptables -A SSL -m recent --update -p tcp --tcp-flags PSH,SYN,ACK SYN,ACK --sport 400 #iptables -A SSL -m recent --update -p tcp --tcp-flags PSH,SYN,ACK ACK --dport 400 #iptables -A SSL -m recent --remove -p tcp --tcp-flags PSH,ACK PSH,ACK --dport 400 -m string --algo kmp --string "subdomain.mydomain.com" -j ACCEPT Yes, I have tried to get around this with nginx tweaks, but I can't get nginx to return a 444 or abrupt disconnect before the client hello, if you can think of a way to achieve this instead, I'm all ears, err, eyes. (As suggested by a user, bringing this inquiry over from http://stackoverflow.com/questions/4628157/allow-connections-to-only-a-specific-url-via-https-with-iptables-m-recent-pote)

  Read the article

• How to fix "The connection was restarted"?

  - by Altar

  I have a php script with ajax. Few days ago, without making any changes, the script stopped working. The script is working sometimes but it is very slow. Other times it doesn't load completely. Yet other times it loads and empty page or it shows a "The connection was restarted" message. We have tried loading the page from 4 different computers in two different countries (two different ISPs). There is nothing relevant in the server's log. We contacted iPage.com hosting support. We sent screenshots. And all we manage to get from them was an incomplete screenshot and the message 'We tested. The page loads'. So, they won't admit the fault. It looks like they loaded the page once and declared it is working and went back to playing solitaire. I know their support. We had all kind of problems with iPage hosting. My questions are: 1. There is any way to make this error more easy to reproduce? I mean instead of fixing the error to get it appear more often. 2. There is any way to test a server response, to see if it drops connections?

  Read the article

• SQL Server 2012 memory usage steadily growing

  - by pgmo

  I am very worried about the SQL Server 2012 Express instance on which my database is running: the SQL Server process memory usage is growing steadily (1.5GB after only 2 days working). The database is made of seven tables, each having a bigint primary key (Identity) and at least one non-unique index with some included columns to serve the majority of incoming queries. An external application is calling via Microsoft OLE DB some stored procedures, each of which do some calculations using intermediate temporary tables and/or table variables and finally do an upsert (UPDATE....IF @@ROWCOUNT=0 INSERT.....) - I never DROP those temporary tables explicitly: the frequency of those calls is about 100 calls every 5 seconds (I saw that the DLL used by the external application open a connection to SQL Server, do the call and then close the connection for each and every call). The database files are organized in only one filgegroup, recovery type is set to simple. Some questions to diagnose the problem: is that steadily growing memory normal? did I do any mistake in database design which probably lead to this behaviour? (no explicit temp-table drop, filegroup organization, etc) can SQL Server manage such a stored procedure call rate (100 calls every 5 seconds, i.e. 100 upsert every 5 seconds, beyond intermediate calculations)? do the continuous "open connection/do sp call/close connection" pattern disturb SQL Server? is it possible to diagnose what is causing such a memory usage? Perhaps queues of wating requests? (I ran sp_who2, but I didn't see a big amount of orphan connections from the external application) if I restrict the amount of memory which SQL Server is allowed to use, may I sooner or later get into trouble?

  Read the article

< Previous Page | 564 565 566 567 568 569 570 571 572 573 574 575  | Next Page >