Search Results

Search found 20904 results on 837 pages for 'disk performance'.

Page 569/837 | < Previous Page | 565 566 567 568 569 570 571 572 573 574 575 576  | Next Page >

• HDD bad sectors with OS

  - by Michael Z

  I wonder is that possible for OS to make bad sectors on Hard Drive? Preface: I have bought new HDD on 1Tb WB Caviar Black. I have installed new OS on ext4 partition Ubuntu 12.04.1 LTS. After few days S.M.A.R.T. of the Ubuntu's Disk Utility show that my hard has bad sectors! I have checked on S.M.A.R.T. immediately after installing OS - all was OK. During new OS working I have noticed some strange with HDD - all OS was freezed from 20 sec to 1 min and I have heard like HDD's engine restarting. At the dmes I have found something like this: [40085.407947] ata1.00: device reported invalid CHS sector 0

  Read the article

• VMWare Server lck file keeps coming back

  - by muncherelli

  I am running VMWare Server 2.0 on a Debian Lenny system as a host OS. I am getting this error when I try to start a Virtual Machine Cannot open the disk '/var/lib/vmware/Virtual Machines//.vmdk' or one of the snapshot disks it depends on. Reason: Failed to lock the file. So I looked around on the web and found that I need to delete the .lck folder and file in order to get this error This seems to happen any time I reboot my Debian Server. The Virtual Machines sometimes do not recover and this lck file is causing problems. Should I create a cron script that does a rm *.lck on each of my machines on reboot? Looking for any direction on how to resolve this. It seems when i do a "reboot" command it is maybe not gracefully shutting down the VMware containers so the lock files are still intact?

  Read the article

• Routing Essentials

  - by zharvey

  I'm a programmer trying to fill a big hole in my understanding of networking basics. I've been reading a good book (Networking Bible by Sosinki) but I have been finding that there is a lot of "assumed" information contained, where terms/concepts are thrown at the reader without a proper introduction to them. I understand that a "route" is a path through a network. But I am struggling with visualizing some routing-based concepts. Namely: How do routes actually manifest themselves in the hardware? Are they just a list of IP addresses that get computed at the network layer, and then executed by the transport? What kind of data exists in a so-caleld routing table? Is a routing-table just the mechanism for holding these lists of IP address (read above)? What are the performance pros/cons for having a static route, as opposed to a dynamic route?

  Read the article

• What settings to use for fastest reloading of a MySQL backup?

  - by Alex R

  I have a MySQL database which dumps to a 3.5 GB backup (mysqldump) in about 10 minutes. But reloading this backup on a standby / test server takes upwards of 12 hours. What are some settings that would maximize reloading performance? The most promising appear to be innodb_buffer_pool_size, innodb_additional_mem_pool_size, and innodb_log_buffer_size... but I'm reaching the limits of my trial-and-error approach. Which of these settings "should" be the most important? Through trial-and-error I was not able to get more than 70% CPU utilization and 63% memory utilization. I'd like both at 100% during a reload. All tables are InnoDB.

  Read the article

• Is it possible to change the default scan folder on an Eye-Fi Wireless SD Card

  - by MichaelPh

  By default Eye-Fi cards scan the DCIM folder (and subfolders) used by most digital cameras for new images to upload. Is there a way of changing this to a different folder? In my particular case I'm using a Kodak photo scanner (P461) that uses a PHOTO(N) folder format to store the scanned images, as far as I know the device has no configuration interface to alter this setting so that doesn't seem to be an option. This topic on the Eye-Fi forums is the closest I've come to a solution, but a perfunctory investigation of Disk Probe doesn't make it obvious what needs to be modified on the card.

  Read the article

• Network backup for Macs and PCs - formatting question

  - by neilfein

  I'm trying to use a LaCie 2TB drive as an AirPort drive, for backup on a home network. We have one mac and two PC laptops. My plan is to create a Mac partition and a Windows partition. However, Disk Utility won't let me set the windows partition to Windows format; there's no option in the menu for it in the partition tab. Am I doing something wrong? Alternatively, is there a way to partition the drive with one partition that all three machines can see? We have a Mac G5 with 10.4 and two laptops with Windows 7. Thanks!

  Read the article

• Windows XP , HP , IntelInside Trobelshooting

  - by Jamil Hneini

  My Windows XP PC has stopped booting. On start up, before Windows boots a screen appears saying: Windows Could Not Boot: Could Not Find or Corrupted file <Windows root>\Sytem32\Hal.dll Please Reinstall the file... From that I understand that I have to reinstall the OS but my computer is so old that I have lost the backup and recovery disk. My Computer's Info: 32Bit Computer Pentium 4 Windows XP Service Pack 2 HP History: My Computer has 4 hard drives 2 internal 40 GB drives (C And D) 2 external 8GB drives (E And F) Additional Info: I need the files inside C And E The computer reads my flash drive as a hard drive (8.45GB)(I have never booted while my USB pluged in while I was troubleshooting) With some test I discovered that the C drive wasn't detected by the computer I have already configured the boot order of BiOS I have Set The SATA to IDE The Question: I have a setup for windows 8 32 bit how can I boot from my USB to run that setup? If that isn't the proper way to handle this problem please tell me the proper way.

  Read the article

• Ubuntu on an XPS 14 Ultrabook with mSATA cache and 500GB HD - how to partition for dual boot?

  - by JDS

  I am getting an XPS 14 ( http://www.dell.com/us/p/xps-14-l421x/pd ) and I want to dual-boot Windows and Ubuntu. This thing has a 500GB standard HD and a 32GB mSATA that can be used as cache. Does anyone know how this thing is partitioned? Is the OS installed on the mSATA drive and data is on the big HD? Is there a BIOS controller or maybe even a Windows driver that makes the mSATA drive and 500GB HD appear contiguous? I get the impression that something makes the mSATA be used invisibly as cache, but I can't find any technical documentation how that works. My primary concern here is wrt dual-booting Ubuntu. I want to know if I need to partition the mSATA separately, or the big HD, or just partition the "magic" contiguous disk space that appears available to the OS.

  Read the article

• CPU fan turns on and off repeatedly without booting

  - by rnso

  My PC has suddenly stopped starting up. On checking with case open, the CPU fan starts running when the power is turned on, but it stops after about 2-3 seconds, restarts again after about 2-3 seconds and the loop is repeated. There is no beep and nothing appears on the screen. On searching the internet, I found there could be several reasons for this. I tried removing hard-disk, CD drive, tightening connections etc but of no avial. I also tried using a new power supply but the response is the same. Where could be the problem and how can it be solved? Thanks in advance.

  Read the article

• How to increase Remote Desktop resolution?

  - by BugAlert

  I'm using Windows 7 on a PC and connect to it via Remote Desktop Connection for Mac by MS, using a Mac. On the Mac, I have a 27" Display with 2560 x 1440 px resolution. The PC has a high performance graphics card (one of those that needs an additional power supply). Both machines are connected via network cable to a router. So network should be insanely fast. However, the max resolution I can get is 1400 x 1050. The PC just has a old and bad 21" monitor connected to it. How can I increase the resolution to 2560 x 1440 to work fullscreen with the Apple LED Cinema Display via Remote Desktop? Maybe I shouldn't even ask, because I already experience some lag at the low resolution of 1400 x 1050. But I guess this can be resolved as well?

  Read the article

• What kind of CPU/GPU integration is offered by APUs?

  - by clabacchio

  I'm truly fascinated by the idea of GPGPU and using the GPU for heavy processing. I'm seeing that also APUs (Accelerated Processing Units, CPU+GPU on the same chip) are gaining a consistent popularity. Are all of the APUs using a GPGPU? Can it be used for processing? And is it seamless or it requires special code (like Cuda) to have the hard work made by the GPU? I'm not interested in bare graphic performance, but more about how much the GPU can accelerate the "normal" CPU work.

  Read the article

• Windows 7, files reappear after deletion.

  - by HeavyWave

  I'm trying to delete some files from a folder. I've taken ownership of the files and the folder. When I delete these files Windows doesn't report any errors and deletes them. BUT, after I press F5 these files reappear again. There are no messages whatsoever, they are just undeletable. I know login off will help, but how do I fix it without going through the pain of closing everything down? P.S. Files disappear from the folder after aprox. 5 minutes. Update. Turns out my version of Windows did not properly upgrade from test version, so it had some weird disk drive issues.

  Read the article

• Make SoX not show output

  - by Ram Rachum

  I'm recording with SoX, and I want to make it not show output at all. When recording, it shows this output: Input File : 'default' (waveaudio) Channels : 2 Sample Rate : 48000 Precision : 16-bit Sample Encoding: 16-bit Signed Integer PCM In:0.00% 00:00:00.68 [00:00:00.00] Out:28.7k [ | ] Clip:0 I tried setting verbosity to 0, but it has no effect. (I'm guessing it's meant for messages other than this.) I don't just want to hide the output, which I could do easily; I want SoX to not generate it in the first place, for performance on a weak computer.

  Read the article

• Older raid controllers in raid 5 vs. Jbod and SW raid

  - by TEB

  Hi. Im in the fortunate position to have 6 Supermicro older VOD servers with the following config: Supermicro 3U case, 3xPSU Dual Xeon 3ghz P4 class cpu (5 years old.. havnt checked the exact type) 4GB Ram 3ware 9500-8 SATA controller 8 SATA SLOTS and alot of free drives. 2GB FLASH Bootdrive What im curious about is the RAID5 performance on these old beasts in HW mode vs. SW on Linux with the controller set in JBOD mode. Im thinking on using Centos 5.5 or Ubuntu or ZFS RaidZ on Opensolaris. Any tips? or reccomendations ? best regards TEB

  Read the article

• using nmap to guess remote OS and probe service details on a single port only

  - by WoJ

  I am looking at scanning with nmap a large network in order to identify the OS of devices (-O--osscan-limit) probe for details of a service on a single port (I would have used -sV for all open ports) The problem is that -sV will probe all the ports (which I do not want to do for performance reasons) and I cannot use -p to limit the ports to the one I am interested in as this impacts the OS fingerprinting. I could not find anything in the manual to limit the service probing. Thank you for any ideas (including other approaches outside of nmap, though I would prefer to stick to nmap)

  Read the article

• Few questions about SLI

  - by toomanyairmiles

  Hi all, thanks in advance for your help. I've just added a second card to my system so I can add a third monitor. I'd got as far as determining both cards need to use the same driver (after a blind alley with another cheap ATi card) so I'm now the proud owner of a second BFG 9800 GTX+ card. One is a BFG OCX and the other an BFG OC (small difference in clock speeds but they are in all other respects the same) but wanted to know the following:- 1) Is it worth adding the SLI connector, will it really boost overall performance (I'm guessing that the OCX card will then perform as the OC card does)? 2) Are SLI connectors (the one's that run across the top of the cards) motherboard or manufacturer specific? 3) If I do SLI the cards will I still be able to use all four monitor connectors or just the two on the master card? I'm not a gamer, I'm an IA and web designer so the system is mostly for Photoshop and Illustrator work and the occasional knock around in command and conquer.

  Read the article

• auspex LFS backups

  - by user1250465

  I have some backup tapes which existed on an AUSPEX file server. The backups were written to tape with the SunOs version of the CPIO command. Now that I need to restore them, (of course there are no more auspex servers in existance), the backups won't restore because the headers are not standard. I have dumped the tape images to disk. PAX, CPIO, and TAR cannot read the images. I've tried all of the CPIO format options. The errors I get are "name too long", "byte swapped in header", or just junk output. I can open up the images and read the contents of the files, but cannot restore the images. I have found that SunOs had a special header in CPIO V2.5 images. I have found the source for cpio, now I need definition of the SunOs header inside CPIO?

  Read the article

• Switching to Linux, Need backup help

  - by Stephen

  I have an existing Vista installation on my thinkpad x200 and I want to install Linux on my machine. I've done this several times already but I usually format the whole disk and dual boot on Windows and Linux. Which means I have to reinstall and reconfigure everything I had on Windows. What I want to do is backup my windows installation (into an image) and start a clean Linux installation, and run the windows image thru Vmware or Virtualbox. Whats the easiest way to do this? any free tools available? I've seen acronis but dont wanna buy it for a 1 time session only.

  Read the article

• Which VNC for Mac to WinXP Home control?

  - by IVR Avenger

  Hi, all. I've got a MacBook and a Windows XP Home machine. I'd like to be able to connect into the XP machine from the Mac over VNC, but not through the Web method, where performance seems to be a bit iffy. I've done some research, and it seems everyone is interested in the XP-Mac connection, where I'm looking to go in the other direction. Is there a free VNC Server out there that will let me accomplish this? Thanks! IVR Avenger

  Read the article

• SCSI vs SATA? Is SCSI "actually" better?

  - by earlz

  Well, I was talking with a guy about servers the other day. I was a bit shocked whenever I asked him if there was any significant difference between SCSI and SATA and why he always uses SCSI. (note, I'm not sure if by SCSI he meant SAS) He told me that SCSI is always faster and that the drives are always more reliable.. I mean, this seems like a bold statement. He told me something about how SCSI will always be faster than SATA because the OS sends the SCSI (controller?) a request to get a file and it will build the file inside of the SCSI controller, instead of searching all over the disk.. which I do not understand how that would work, so I figure it is BS. SAS and SATA currently have equivalent data rate speeds.. Is there any true backing for his reasoning that SCSI is always faster and more reliable than SATA?

  Read the article

• Allow READ access to local folders in 2003SBS AD

  - by Dan M.

  Have a SBS2003 client with a mess of a domain that is in process of being cleaned. But, for the life of me I cannot find a setting that will allow write access to the local hard disk for domain users with redirected profiles(to the server). This is needed only for one program that will not follow a symbolic link to the network path, instead it seems to be hard coded to the %appdata% folder but only on the c: drive.... So question is how can I allow "Domain users" write access to the local %appdata% directory? I have tried setting it manually on a machine but it kept resetting to RO no matter how many times I tried. Everytime I would uncheck the RO property it would reset sometime right after i hit OK. Thanks in advance! Dan

  Read the article

• Timeouts when connecting to SQL Server since installing SP1 for Windows 7

  - by Julien

  Hi, I just installed SP1 for windows 7 and I have severe performance degradation when connecting to SQL Server 2005 since then. Establishing connection takes more than 30 seconds while it's instantaneous on another computer. Firewall is disabled and I didn't make any change to the configuration. It happens both when trying to connect with a hostname and with an ip address. Everything else seems to be fine (for instance, I'm have no issue connecting to other computers with remote desktop) What can cause such a problem? Thanks in advance! Edit : uninstalling the SP1 solves the issue instantly.

  Read the article

• Best practice for scaling a single application source to multiple nodes

  - by Andrew Waters

  I have an application which needs to scale horizontally to cover web and service nodes (at the moment they're all on one) but interact with the same set of databases and source files (both application code and custom assets). Database is no problem, it's handled already with replication in MongoDB. Also, the configuration of the servers are the same (100% linux). This question is literally about sharing a filesystem between machines so that its content is always correct, regardless of the node accessing it. My two thoughts have so far been NFS and SAN - SAN being prohibitively expensive and NFS seeing some performance issues on the second node with regards to glob()ing in PHP. Does anyone have recommended strategies or other techniques that don't involved sharding data across nodes or any potential gotchas in NFS that may cause slow disk seek times? To give you an idea of the scale, the main node initialises it's application modules in ~ 0.01 seconds. The secondary is taking ~2.2 seconds. They're VM's inside a local virtual network in ESXi and ping time between them is ~0.3ms

  Read the article

• Open Source Visualization and Dashboard Software

  - by helios

  I am working on an open source Application Performance Monitoring (APM) software and looking for a visualization tool with dashboard capabilities. I came across Graphite which looks pretty good but wondering if there is anything better out there before I settle down with that tool. Here's the list of features I am interested in: Must-Have Open Source license API to submit real time data Web-based visualization interface Persistence - file or database Nice-To-Have Dashboard Capabilities: Allow users to select a few metrics (CPU, Heap Usage, # of Active Users etc.) and place them on a single page for easier monitoring. Any suggestions?

  Read the article

• Where should I go to learn about networking? [closed]

  - by Ollie Saunders

  I wonder if anyone could recommend resource or resources such as a good book that: explains how all the important protocols work and interact. I’m interested in those that are relevant in a typical home network and used over the Internet explains in detail how ADSL Internet connections work to the level of depth necessary so that I’m able to tweak and measure performance settings starts from the beginning but attempts to provide proper understanding rather than idiot-oriented steps to follow Basically, I’m interested in how these technologies work and tend to be implemented in hardware and software rather than “here’s what to do if…” I’m interested in Computer Networking by Andrew S. Tanenbaum and I wonder if anyone else has any experience with that title. It’s expensive but I could probably loan a copy for £3 from the library or so.

  Read the article

< Previous Page | 565 566 567 568 569 570 571 572 573 574 575 576  | Next Page >