Search Results

Search found 28563 results on 1143 pages for 'strange but true'.

Page 570/1143 | < Previous Page | 566 567 568 569 570 571 572 573 574 575 576 577  | Next Page >

• php on ubuntu 13.10 won't get parsed

  - by fefe

  I'm facing a strange issue with a fresh installed ubuntu 13.10 apache2 with mysql and php. My php won't get parsed and I have been doing every changes what I found during my researches PHP 5.5.3-1ubuntu2 (cli) (built: Oct 9 2013 14:49:12) sudo a2enmod php5 apache2.conf <FilesMatch \.php$> SetHandler application/x-httpd-php </FilesMatch> /etc/apache2/mods-enabled/php5.conf </FilesMatch> # Deny access to files without filename (e.g. '.php') <FilesMatch "^\.ph(p[345]?|t|tml|ps)$"> Order Deny,Allow Deny from all </FilesMatch> # Running PHP scripts in user directories is disabled by default # # To re-enable PHP in user directories comment the following lines # (from <IfModule ...> to </IfModule>.) Do NOT set it to On as it # prevents .htaccess files from disabling it. #<IfModule mod_userdir.c> # <Directory /home/*/public_html> # php_admin_value engine Off # </Directory> #</IfModule>

  Read the article

• Use Apache authentication + authorization to control access to Subversion subdirectories

  - by Stefan Lasiewski

  I have a single SVN repo at /var/svn/ with a few subdirectories. Staff must be able to access the top-level directory and all subdirectories within it, but I want to restrict access to subdirectories using alternate htpasswd files. This works for our Staff. <Location /> DAV svn SVNParentPath /var/svn AuthType Basic AuthBasicProvider ldap # mod_authnz_ldap AuthzLDAPAuthoritative off AuthLDAPURL "ldap.example.org:636/ou=people,ou=Unit,ou=Host,o=ldapsvc,dc=example,dc=org?uid?sub?(objectClass=PosixAccount)" AuthLDAPGroupAttribute memberUid AuthLDAPGroupAttributeIsDN off Require ldap-group cn=staff,ou=PosixGroup,ou=Unit,ou=Host,o=ldapsvc,dc=example,dc=org </Location> Now, I am trying to restrict access to a subdirectory with a separate htpasswd file, like this: <Location /customerA> DAV svn SVNParentPath /var/svn # mod_authn_file AuthType Basic AuthBasicProvider file AuthUserFile /usr/local/etc/apache22/htpasswd.customerA Require user customerA </Location> I can use Firefox and curl to browse to this folder fine: curl https://svn.example.org/customerA/ --user customerA:password But I cannot use check out this SVN repository: $ svn co https://svn.example.org/customerA/ svn: Repository moved permanently to 'https://svn.example.org/customerA/'; please relocate And on the server logs, I get this strange error: # httpd-access.log 192.168.19.13 - - [03/May/2010:16:40:00 -0700] "OPTIONS /customerA HTTP/1.1" 401 401 192.168.19.13 - customerA [03/May/2010:16:40:00 -0700] "OPTIONS /customerA HTTP/1.1" 301 244 # httpd-error.log [Mon May 03 16:40:00 2010] [error] [client 192.168.19.13] Could not fetch resource information. [301, #0] [Mon May 03 16:40:00 2010] [error] [client 192.168.19.13] Requests for a collection must have a trailing slash on the URI. [301, #0] My question: Can I restrict access to Subversion subdirectories using Apache access controls? DocumentRoot is commented out, so it's not clear that the FAQ at http://subversion.apache.org/faq.html#http-301-error applies.

  Read the article

• vyatta Server Reboots by itself

  - by Fernando

  I have an issue regarding some hardware, maybe you can help me. First, I set up a Supermicro Superserver SYS-5016I-NTF with a Intel Xeon X3470 and 4 GB of Ram with a Hotlava Card Tambora 64G4 with Intel Chipset 82599EB and 4x10G SPF+ ports. Installed Vyatta community edition 6.3. I used it as router making BGP connections with 2 operators. No load at all, temp ranges normal. But the issue is that it reboots by itself in a ramdom way. Not very often, once every few days. But it is unacceptable for production purposes. So I try to test on different hardware, and installed Vyatta community edition 6.3 on a Dell PowerEdge 2950, with Xeon(R) E5345 @ 2.33GHz and 4 GB of Ram. Same Vyatta configuration as Supermicro Server. With same hotlava Card model ( I bought two of them ) Well I have reboots with this equipment as well. Same frecuency as above. I have checked syslog no strange logs until boot process starts to be logged. So it seems server reboot suddenly. I have installed latest driver for the chipset of the Hotlava card. Servers are placed in a datacenter with UPS So finally two things in common in both servers: Hotlava Card. Someone with issues with this card, or the chipset?? Could be it this card?? Vyatta 6.3 community edition. I don't thing is the problem. Is a regular Debian with packages to glue together different services. Or maybe is something I am missing. Andy ideas, suggestions?? Thank you very much... Fernando

  Read the article

• Using Toshiba 22EL833 as PC display with GTX8800

  - by Oleg V. Volkov

  I had another Toshiba TV - 19SL738 - connected to this same PC and video card (GTX 8800) through DVI<-HDMI (DVI on PC side, HDMI on TV) before, that was working perfectly at it's native resolution 1360x768. Some time ago I had to change to 22EL833 and immediately faced problem with Windows 7 control panel and NVIDIA control panel both reporting native resolution for new TV as 1080i, 1920x1280, despite TV documentation saying that it have same 1360x768 as previous one. Practical tests confirmed that true native resolution is indeed 1360x768, because plugging in through DVI<-VGA and setting custom resolution through NVIDIA panel shown clear colors and crisp image, while setting anything different with either DVI<-VGA or DVI<-HDMI produced horribly distorted or squished images, with almost unreadable slim lines (as in letters, for example). Now, my problem is that there's no drivers for this TV and I'm unable to get good image while connecting it through DVI<-HDMI directly. The best I've achieved is editing EDID/driver manually, to persuade system that native resolution should be 1360x768, and while image became mostly clear, colors turned to some strange washed out effect, with pools of pure yellow, cyan and magenta there and there filling place of other colors. Gradients also became noticeably stripped as well. Somehow it looks like dithering gone bad and makes me suspect that image is still down/upscaled several times internally somewhere along the line. How can I connect this TV to DVI output of my video card to get best possible clear image, correct colors and correct native resolution?

  Read the article

• wget is working only when used with sudo

  - by Yusuf

  I'm having quite a strange behavior with wget since yesterday. I can download files by using sudo wget, but when I try the same file with only wget, I can get this error: yusufh@ubuntu-yuh:~$ wget http://www.kegel.com/wine/winetricks --2010-12-17 09:34:11-- http://www.kegel.com/wine/winetricks Resolving www.kegel.com... failed: Name or service not known. wget: unable to resolve host address `www.kegel.com' and with sudo wget: yusufh@ubuntu-yuh:~$ sudo wget http://www.kegel.com/wine/winetricks --2010-12-17 09:35:37-- http://www.kegel.com/wine/winetricks Connecting to 127.0.0.1:5865... connected. Proxy request sent, awaiting response... 200 OK Length: 190672 (186K) [text/plain] Saving to: `winetricks' 100%[==================================================================================================>] 190,672 --.-K/s in 0.03s 2010-12-17 09:35:37 (6.92 MB/s) - `winetricks' saved [190672/190672] After the comments below, here is an update: I can use Google Chrome or Firefox perfectly without running it as root. I use ntlmaps to connect to the office proxy. So I need to use 127.0.0.1:5865 as the proxy for clients. Result for env | grep -i proxy: NO_PROXY=localhost,127.0.0.0/8,*.local, http_proxy=127.0.0.1:5865 ftp_proxy=127.0.0.1:5865 all_proxy=socks://127.0.0.1:5865/ ALL_PROXY=socks://127.0.0.1:5865/ https_proxy=127.0.0.1:5865 no_proxy=localhost,127.0.0.0/8,*.local while sudo env | grep -i proxy is empty! HELP!

  Read the article

• Keyboard issue when using kitty+puttycyg but not when using putty or cygwin alone

  - by kamaradclimber

  I would like to use a unique way to use console on my windows setup. Previously I used putty for remote access to linux servers and cygwin to have unix-like tools on windows. Then I discovered kitty which is a patched putty and have added the puttycyg patch. It provides the same way to connect to remote and local console. However, there is a strange behavior using vim when connected to the local console (using the puttycyg patch) : keys display A/B/C/D and replace the current character by these letter. In insert mode it does replace the caracter, in normal mode, no modification is made to the document even if the caracter is displayed as replaced. For instance, when I type : fixed bug with product deleted I get : fixed bbug wiwith prprodudueleteted I have read a lot of questions about this type of issue 3, 4 and googled it but there is no answer that work for me. The issue is present only for the setup kitty+puttycyg patch : cygwin alone works perfectly (and putty alone works also for access to linux servers). Any help would be appreciated !

  Read the article

• OpenVPN IPV6 Tunnel Radvd

  - by Arenstar

  Hello.. I have an interesting question regarding ipv6 + openvpn.. My Version is OpenVPN 2.1.1 i have been given a native /64 ipv6 network ( for this example 2001:acb:132:acb::/64 ) The plan was/is, route this block through openvpn and into an office ( for testing purposes ) Soo to explain.. I have a Centos Box as the first linux "router" in a datacenter & a Ubuntu box as the second linux "router" in the office I have created a simple point-to-point tunnel using tun ( based off ipv4 address to start the tunnel ) I have assigned to Centos /sbin/ip addr add fed1::1/128 dev eth0 /sbin/ip addr add fed2::2/128 dev tun0 /sbin/ip route add 2001:acb:132:acb::/64 dev tun0 ## ipv6 Block down the tunnel /sbin/ip route add ::/0 dev eth0 ## Default out to Gateway I have assigned to Ubuntu /sbin/ip addr add fed1::3/128 dev tun0 /sbin/ip addr add fed1::4/128 dev eth0 /sbin/ip route add 2001:acb:132:acb::/64 dev eth0 ## ipv6 Block down to eth0 /sbin/ip route add ::/0 dev tun0 ## Default up the tunnel I have also included on both servers.. sysctl -w net.inet6.ip6.forwarding=1 Looks Good... right??? Wrong.. :( I am not able to ping fed1::1 from fed1::4 (Ubuntu) (can ping :4,:3,:2) However, i can ping fed1::1 fed1::2 from :3 ?????? ( very strange ) I am able to access the internet from any ipv6 interface on the Centos Box but clearly not from the Ubuntu box.. Further, i will eventually run radvd on the Ubuntu box eth0, and autoconf the network with ipv6 address's Anyone with some advice / tips to help me out.. ??? Cheers

  Read the article

• Why is my connection slow?

  - by Jay R.

  I have a Dell Precision T5400 with a Broadcom 1Gb onboard NIC. For some strange reason, when I access machines on our local network, the best I can get is around 125KB/s download speed. My laptop that has a 10/100Mb NIC onboard usually gets around 300KB/s or better from the same network resource. Both machines are plugged into the same 1Gb switch which connects to our local network wall jack at 100Mb half duplex. There is also a printer plugged into the same switch at 100Mb full. The resource I'm using for the test is a 30MB zip file copied from a jetty webserver that is running as part of a cruisecontrol installation. The cruisecontrol installation is running WindowsXP with full real-time antivirus and Altiris patch management and inventory running. That stuff on its own is eating some of the download speed. I've seen the laptop reach into the multiple MB/s download speed before, but the desktop never seems to get past 125KB/s to 130KB/s. In WindowsXP, before I upgraded the driver in the desktop, it was that slow. In Fedora, it is still slow even though it appears to be using the same driver version as the upgraded Windows driver. The upgraded Windows driver is faster, but still not nearly as fast as the laptop. What gives? Any insight to improve the situation would be appreciated. Could it be that the BroadCom board just isn't that good, or the driver in linux is just not as good as the Windows one?

  Read the article

• Apache stops responding to http requests -- https continues to work

  - by Apropos

  Okay. Very strange problem that I'm having here. I just recently updated to Apache 2.4.2 from 2.2.17, mostly to try to get name-based SSL VirtualHosts working (although they should have been working on 2.2.17). Server is Win2008 R2 (so x64 by definition) running with PHP 5.4.3 and MySQL 5.1.40 (outdated, I know). When I launch the server, it initially works fine. Responds to all requests, VirtualHosts all in order. However, after an uncertain amount of time (appears to only take a few minutes for the most part, but sometimes takes hours), it stops responding to regular HTTP requests (on any VirtualHost). HTTPS continues to work. No errors in the log, and nothing in the access logs when I attempt to connect. I'm having a hard time finding the source of this error given its intermittent nature. When removing all SSL-based VirtualHosts, it seemingly increased stability (still responding to HTTP requests twelve hours later). This could be mere coincidence, though. Entirety of SSL VirtualHost is as follows, should there happen to be a problem with it. <VirtualHost *:443> DocumentRoot "C:\Server\www\virtualhosts\mysite.net" ErrorLog logs/ssl.mysite.net-error_log CustomLog logs/ssl.mysite.net-access_log common env=!dontlog SSLEngine on SSLProtocol all -SSLv2 SSLCipherSuite ALL:!ADH:!EXPORT:!SSLv2:RC4+RSA:+HIGH:+MEDIUM SSLCertificateFile C:/Server/bin/apache/apache2.4.2/conf/ssl/server.crt SSLCertificateKeyFile C:/Server/bin/apache/apache2.4.2/conf/ssl/server.key SSLCertificateChainFile C:/Server/bin/apache/Apache2.4.2/conf/ssl/sub.class1.server.ca.pem SSLCACertificateFile C:/Server/bin/apache/Apache2.4.2/conf/ssl/ca.pem </VirtualHost> Any ideas what I'm missing?

  Read the article

• Adding a GET parameter to URL causes 404 error

  - by Adrian Grigore

  I'm trying to install the syntaxhighlightter evolved plugin to my wordpress blog. I've uploaded and activated the plugin, but it did not work. I've looked into the page source code and found out that the plugin style is loaded from the following URL: http://devermind.com/wp-content/plugins/syntaxhighlighter/syntaxhighlighter/styles/shCore.css?ver=2.0.320 This causes a 404 error (page not found). The strange thing though is that when I remove the GET parameters, the CSS loads ok: http://devermind.com/wp-content/plugins/syntaxhighlighter/syntaxhighlighter/styles/shCore.css What could be causing this problem and how can I fix this? Unfortunately I don't know how to make wordpress drop the GET parameters when loading the stylesheet. EDIT: As I just found out, this happens only in Firefox (3.0.11). IE loads both URLs above just fine. Not that this would be of any help though, so any suggestions would be appreciated. SECOND EDIT: I tried this on my laptop and it works fine with Firefox 3.08. So this really seems to be a browser problem after all.

  Read the article

• Loss of network connectivity when playing video on Optoma HD180 projector

  - by Jeff Fohl

  Hi Folks - New to Super User, so I hope this question fits in with the guidelines. Very strange problem I am having, and I am at a loss as to how to continue troubleshooting this one. The basic problem is that when I attempt to watch streamed video on a particular display device (an Optoma HD180 projector), my network connectivity drops like a stone to barely measurable levels. This is my setup: I have a Dell H2C 730x running Windows 7 64bit. This particular computer has two ATI Radeon HD 4800 video cards. I have two Samsung 22" monitors connected to one card, and an Optoma HD180 digital projector connected to the other card via an HDMI cable. My internet connection is normally a reliable 6Mbps. The problem I am having occurs when I stream video (or even just browse the web) on the Optoma Projector. When I do this, my internet connection drops to practically zero (just a few kilobits per second). When I move the browser away from the projector, and over to one of my Samsung monitors, the internet connection comes right back. Note that the Optoma projector is on and enabled as a third monitor all this time. I can move the mouse around on the projector without triggering the problem. I tried pinging my router when I was playing a movie on one of the monitors, and I get a 1 millisecond response. However, when I have the movie playing on the Optoma projecter, pinging the router gives me response times in the hundreds of milliseconds, or times out completely. So, it clearly is something local to my machine - and not some sort of throttling occurring down the line. I would think that it is possibly something to do with the HDMI driver conflicting somehow with my network driver (which is a USB-based wireless connection). This one has me really stumped. Anyone have any ideas?

  Read the article

• Unable to access network resources through VPN

  - by fbueckert

  I'm currently attempting to connect one of our computers in the office to a client VPN. My development machine is running Windows 7, and can connect and see resources just fine. The problem computer is running Windows XP. They're both within the same network. Using the same credentials at both computers, the VPN connection (using the built in Windows network connections) works just fine. So far, so good. An IP address is assigned, and comparing both machines shows they're still in the same subnet. The problem is that the XP machine cannot see ANY of the computers in the client network. I tried a tracert to a target machine on the Windows 7 box, and the first item that comes up is the .0 address. Pinging it gives responses. Trying it on the Windows XP machine, however, comes up with just timeouts. Trying to trace to www.google.com allows the address to resolve (probably part of the cached resolutions), but results in just timeouts. I double-checked to make sure that the Windows firewall was not on, and trying to open the settings brings up a notification that the firewall service wasn't running, which leads me to believe that it's definitely not on. From my best guess, I've managed to connect the XP machine to a black hole of some sort. There's obviously something strange going on, but I'm not sure where I should be looking.

  Read the article

• Nginx + PHP-FPM Timeouts, almost zero load consumption?

  - by javipas

  I've got a server running on a Linode with Ubuntu 10.04 LTS, Nginx 0.7.65, MySQL 5.1.41 and PHP 5.3.2 with PHP-FPM. There is a WordPress blog on it, updated to WordPress 3.2.1 recently. I have made no changes to the server (except updating WordPress) and while it was running fine, a couple of days ago I started having downtimes. I tried to solve the problem, and checking the error_log I saw many timeouts and messages that seemed to be related to timeouts. The server is currently logging this kind of errors: 2011/07/14 10:37:35 [warn] 2539#0: *104 an upstream response is buffered to a temporary file /var/lib/nginx/fastcgi/2/00/0000000002 while reading upstream, client: 217.12.16.51, server: www.mydomain.com, request: "GET /page/2/ HTTP/1.0", upstream: "fastcgi://127.0.0.1:9000", host: "www.mydomain.com", referrer: "http://www.mydomain.com/" 2011/07/14 10:40:24 [error] 2539#0: *231 upstream timed out (110: Connection timed out) while reading response header from upstream, client: 46.24.245.181, server: www.mydomain.com, request: "GET / HTTP/1.1", upstream: "fastcgi://127.0.0.1:9000", host: "www.mydomain.com", referrer: "http://www.google.es/search?sourceid=chrome&ie=UTF-8&q=mydomain" and even saw this previous serverfault discussion with a possible solution: to edit /etc/php/etc/php-fpm.conf and change request_terminate_timeout=30s instead of ;request_terminate_timeout= 0 The server worked for some hours, and then broke again. I edited the file again to leave it as it was, and restarted again php-fpm (service php-fpm restart) but no luck: the server worked for a few minutes and back to the problem over and over. The strange thing is, although the services are running, htop shows there is no CPU load (see image) and I really don't know how to solve the problem. The config files are on pastebin The php-fpm.conf file is here The /etc/nginx/nginx.conf is here The /etc/nginx/sites-available/www.mydomain.com is here Please help :(

  Read the article

• Proliant server will not accept new hard disks in RAID 1+0?

  - by Leigh

  I have a HP ProLiant DL380 G5, I have two logical drives configured with RAID. I have one logical drive RAID 1+0 with two 72 gb 10k sas 1 port spare no 376597-001. I had one hard disk fail and ordered a replacement. The configuration utility showed error and would not rebuild the RAID. I presumed a hard disk fault and ordered a replacement again. In the mean time I put the original failed disk back in the server and this started rebuilding. Currently shows ok status however in the log I can see hardware errors. The new disk has come and I again have the same problem of not accepting the hard disk. I have updated the P400 controller with the latest firmware 7.24 , but still no luck. The only difference I can see is the original drive has firmware 0103 (same as the RAID drive) and the new one has HPD2. Any advice would be appreciated. Thanks in advance Logs from server ctrl all show config Smart Array P400 in Slot 1 (sn: PAFGK0P9VWO0UQ) array A (SAS, Unused Space: 0 MB) logicaldrive 1 (68.5 GB, RAID 1, Interim Recovery Mode) physicaldrive 2I:1:1 (port 2I:box 1:bay 1, SAS, 73.5 GB, OK) physicaldrive 2I:1:2 (port 2I:box 1:bay 2, SAS, 72 GB, Failed array B (SAS, Unused Space: 0 MB) logicaldrive 2 (558.7 GB, RAID 5, OK) physicaldrive 1I:1:5 (port 1I:box 1:bay 5, SAS, 300 GB, OK) physicaldrive 2I:1:3 (port 2I:box 1:bay 3, SAS, 300 GB, OK) physicaldrive 2I:1:4 (port 2I:box 1:bay 4, SAS, 300 GB, OK) ctrl all show config detail Smart Array P400 in Slot 1 Bus Interface: PCI Slot: 1 Serial Number: PAFGK0P9VWO0UQ Cache Serial Number: PA82C0J9VWL8I7 RAID 6 (ADG) Status: Disabled Controller Status: OK Hardware Revision: E Firmware Version: 7.24 Rebuild Priority: Medium Expand Priority: Medium Surface Scan Delay: 15 secs Surface Scan Mode: Idle Wait for Cache Room: Disabled Surface Analysis Inconsistency Notification: Disabled Post Prompt Timeout: 0 secs Cache Board Present: True Cache Status: OK Cache Status Details: A cache error was detected. Run more information. Cache Ratio: 100% Read / 0% Write Drive Write Cache: Disabled Total Cache Size: 256 MB Total Cache Memory Available: 208 MB No-Battery Write Cache: Disabled Battery/Capacitor Count: 0 SATA NCQ Supported: True Array: A Interface Type: SAS Unused Space: 0 MB Status: Failed Physical Drive Array Type: Data One of the drives on this array have failed or has Logical Drive: 1 Size: 68.5 GB Fault Tolerance: RAID 1 Heads: 255 Sectors Per Track: 32 Cylinders: 17594 Strip Size: 128 KB Full Stripe Size: 128 KB Status: Interim Recovery Mode Caching: Enabled Unique Identifier: 600508B10010503956574F305551 Disk Name: \\.\PhysicalDrive0 Mount Points: C:\ 68.5 GB Logical Drive Label: A0100539PAFGK0P9VWO0UQ0E93 Mirror Group 0: physicaldrive 2I:1:2 (port 2I:box 1:bay 2, S Mirror Group 1: physicaldrive 2I:1:1 (port 2I:box 1:bay 1, S Drive Type: Data physicaldrive 2I:1:1 Port: 2I Box: 1 Bay: 1 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 73.5 GB Rotational Speed: 10000 Firmware Revision: 0103 Serial Number: B379P8C006RK Model: HP DG072A9B7 PHY Count: 2 PHY Transfer Rate: Unknown, Unknown physicaldrive 2I:1:2 Port: 2I Box: 1 Bay: 2 Status: Failed Drive Type: Data Drive Interface Type: SAS Size: 72 GB Rotational Speed: 15000 Firmware Revision: HPD9 Serial Number: D5A1PCA04SL01244 Model: HP EH0072FARUA PHY Count: 2 PHY Transfer Rate: Unknown, Unknown Array: B Interface Type: SAS Unused Space: 0 MB Status: OK Array Type: Data Logical Drive: 2 Size: 558.7 GB Fault Tolerance: RAID 5 Heads: 255 Sectors Per Track: 32 Cylinders: 65535 Strip Size: 64 KB Full Stripe Size: 128 KB Status: OK Caching: Enabled Parity Initialization Status: Initialization Co Unique Identifier: 600508B10010503956574F305551 Disk Name: \\.\PhysicalDrive1 Mount Points: E:\ 558.7 GB Logical Drive Label: AF14FD12PAFGK0P9VWO0UQD007 Drive Type: Data physicaldrive 1I:1:5 Port: 1I Box: 1 Bay: 5 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 300 GB Rotational Speed: 10000 Firmware Revision: HPD4 Serial Number: 3SE07QH300009923X1X3 Model: HP DG0300BALVP Current Temperature (C): 32 Maximum Temperature (C): 45 PHY Count: 2 PHY Transfer Rate: Unknown, Unknown physicaldrive 2I:1:3 Port: 2I Box: 1 Bay: 3 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 300 GB Rotational Speed: 10000 Firmware Revision: HPD4 Serial Number: 3SE0AHVH00009924P8F3 Model: HP DG0300BALVP Current Temperature (C): 34 Maximum Temperature (C): 47 PHY Count: 2 PHY Transfer Rate: Unknown, Unknown physicaldrive 2I:1:4 Port: 2I Box: 1 Bay: 4 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 300 GB Rotational Speed: 10000 Firmware Revision: HPD4 Serial Number: 3SE08NAK00009924KWD6 Model: HP DG0300BALVP Current Temperature (C): 35 Maximum Temperature (C): 47 PHY Count: 2 PHY Transfer Rate: Unknown, Unknown

  Read the article

• Wireless connection drops when wired computer starts a game.

  - by Skadlig

  Starting this week I have had a strange problem on my network. Some background of my setup: Internet is provided by a adsl-modem. A D-link Dir-600 router is hooked up to to adsl-modem. My computer is hooked up to the router using a cat-5 cable. My wife's computer is hooked up using a wireless usb dongle, TP-Link TL-WN821N. Both computers use windows 7 64-bit home premium. Up until this week everything was normal, we could for instance play Dungeons & Dragons Online together without any network issues. Now every time I start DDO or any other network game, for instance L4D, the whole wireless network drops. I have confirmed that it's not just her computer using an Samsung Galaxy Spica android phone. Shutting down the game on my end restores the wireless connection automagicly. My wife can start DDO without the net dropping but if I plug in a wireless network card in my computer and start up the game the connection drops. So it seems like something my computer, and my computer only, does when starting a game makes the wireless connection write a sad note and kill it self but for the life of me I can't figure out what that might be. I could hook her computer up using cat-5 but I would prefer not to do that. Does anyone have any suggestions as to what the problem might be, what I can do to fix it or what I should do to get more data regarding what is happening?

  Read the article

• No apparent reason for high load average

  - by Oz.

  We have several web servers running on Amazon (ec2) c1.xlarge, over Amazon AMI. The servers are duplicates of each other, running the exact same hardware and software. Each server spec is: 7 GB of memory 20 EC2 Compute Units (8 virtual cores with 2.5 EC2 Compute Units each) 1690 GB of instance storage 64-bit platform I/O Performance: High API name: c1.xlarge A couple of weeks ago we have run a yum upgrade on one of the servers. Starting on this upgrade the upgraded server started showing a high load average. Needless to say, we did not update the other servers and we can not do so until we understand the reason for this behavior. The strange thing is that when we compare the servers using top or iostat, we can not find the reason for the high load. Note that we have moved traffic from the "problematic" server to the others, which have made the "problematic" server less crowded in terms of requests, and still his load is higher. Do you have any idea what could it be, or where else can we check? Many thanks for the help! Oz. # # proper server # w command # 00:42:26 up 2 days, 19:54, 2 users, load average: 0.41, 0.48, 0.49 USER TTY FROM LOGIN@ IDLE JCPU PCPU WHAT pts/1 82.80.137.29 00:28 14:05 0.01s 0.01s -bash pts/2 82.80.137.29 00:38 0.00s 0.02s 0.00s w # # proper server # iostat command # Linux 3.2.12-3.2.4.amzn1.x86_64 _x86_64_ (8 CPU) avg-cpu: %user %nice %system %iowait %steal %idle 9.03 0.02 4.26 0.17 0.13 86.39 Device: tps Blk_read/s Blk_wrtn/s Blk_read Blk_wrtn xvdap1 1.63 1.50 55.00 367236 13444008 xvdfp1 4.41 45.93 70.48 11227226 17228552 xvdfp2 2.61 2.01 59.81 491890 14620104 xvdfp3 8.16 14.47 94.23 3536522 23034376 xvdfp4 0.98 0.79 45.86 192818 11209784 # # problematic server # w command # 00:43:26 up 2 days, 21:52, 2 users, load average: 1.35, 1.10, 1.17 USER TTY FROM LOGIN@ IDLE JCPU PCPU WHAT pts/0 82.80.137.29 00:28 15:04 0.02s 0.02s -bash pts/1 82.80.137.29 00:38 0.00s 0.05s 0.00s w # # problematic server # iostat command # Linux 3.2.20-1.29.6.amzn1.x86_64 _x86_64_ (8 CPU) avg-cpu: %user %nice %system %iowait %steal %idle 7.97 0.04 3.43 0.19 0.07 88.30 Device: tps Blk_read/s Blk_wrtn/s Blk_read Blk_wrtn xvdap1 2.10 1.49 76.54 374660 19253592 xvdfp1 5.64 40.98 85.92 10308946 21612112 xvdfp2 3.97 4.32 93.18 1087090 23439488 xvdfp3 10.87 30.30 115.14 7622474 28961720 xvdfp4 1.12 0.28 65.54 71034 16487112

  Read the article

• Is ffmpeg incorrectly interpreting .aif files?

  - by marue

  Being on an Ubuntu 10.04 server i installed the ffmpeg packages with apt. ffmpeg is working afterwards, and doing as it should. Almost. For testing purposes i uploaded a few audiofiles. One of them, an aif file, is not being correctly interpreted. While on my workhorse (Mac SnowLeopard) ffmpeg tells the format as Stream #0.0: Audio: pcm_s24be, 44100 Hz, 2 channels, s32, 2116 kb/s my Ubuntu server says it is: Stream #0.0: Audio: pcm_s24be, 44100 Hz, stereo, s16, 2116 kb/s which is the wrong bitdepth. Ubuntu then fails to convert the file with the error message [pcm_s24be @ 0xcd4b580]invalid PCM packet Error while decoding stream #0.0 which certainly is not true. The file is perfectly valid. Are there any know issues for ffmpeg interpreting the aif format? How can i find out which version of the aif-codec ffmpeg is using? Any ideas how to approach this issue? ffprobe output: FFprobe version SVN-r20090707, Copyright (c) 2007-2009 Stefano Sabatini libavutil 49.15. 0 / 49.15. 0 libavcodec 52.20. 0 / 52.20. 1 libavformat 52.31. 0 / 52.31. 0 built on Jan 20 2010 00:13:01, gcc: 4.4.3 20100116 (prerelease) Input #0, aiff, from 'testfile.aif': Duration: 00:00:04.00, start: 0.000000, bitrate: 2117 kb/s Stream #0.0: Audio: pcm_s24be, 44100 Hz, stereo, s16, 2116 kb/s update 2: Forcing the conversion with -sample_fmt s32 doesn't change anything. Strange thing is: Even without using -sample_fmt s32 i just realized that the conversion is working and creates valid audiofiles. There just is the error message from above.

  Read the article

• Truncated content with Apache on Vagrant VM

  - by Nev Stokes

  I'm using Vagrant to run a CentOS VM in order to try and achieve local development parity with our live servers. I've symlinked /var/www/html with the /vagrant shared directory and am forwarding port 80 for viewing at http://localhost:4567. I'm developing using SublimeText 2 on OS X Mountain Lion. Once I figured that iptables was tripping me up, all was well and good. Until I noticed something strange. I have a sample HTML page consisting of several paragraphs of lorem copy. I can view this fine in a browser on OS X. But when I make an edit, for example removing a paragraph, and refresh the content is truncated with the paragraph I deleted still visible. When I cat the files on the server I can see the changes I made but these aren't even reflected when I curl localhost. I strongly suspect that it's a problem with my Apache settings — with which I didn't really tinker — as the issue doesn't arise when I stop Apache and run sudo python -m SimpleHTTPServer 80 in the directory to view pages instead. What gives?

  Read the article

• postfix takes 60-90ms to queue email -- normal?

  - by Jeff Atwood

  We're seeing some (maybe?) strange delays when submitting individual emails to our local Postfix server. To help diagnose the issue, I wrote a little test program which sends 5 emails: get smtp 1ms ( 1 ms) email 0 677ms (676 ms) email 1 802ms (125 ms) email 2 890ms ( 88 ms) email 3 973ms ( 83 ms) email 4 1088ms (115 ms) Discounting the handshaking in the first email, that's about 90ms per email. These timings have also been corroborated with another test app written by someone else using a different codepath, so it appears to be server related. I turned on detailed logging and I can see that the delay is between the end of message \r\n\r\n and the receive: [16:31:29.95] [SEND] \r\n.\r\n [16:31:30.05] [RECV] 250 2.0.0 Ok: queued as B128E1E063\r\n [16:31:30.08] [SEND] \r\n.\r\n [16:31:30.17] [RECV] 250 2.0.0 Ok: queued as 4A7DE1E06E\r\n [16:31:30.19] [SEND] \r\n.\r\n [16:31:30.27] [RECV] 250 2.0.0 Ok: queued as 68ACC1E072\r\n [16:31:30.28] [SEND] \r\n.\r\n [16:31:30.34] [RECV] 250 2.0.0 Ok: queued as 7EFFE1E079\r\n [16:31:30.39] [SEND] \r\n.\r\n [16:31:30.45] [RECV] 250 2.0.0 Ok: queued as 9793C1E07A\r\n The time intervals tell the story (discounting the handshaking required for the initial email) -- each email is waiting about 60-90 milliseconds for postfix to queue! This seems .. excessive .. to me. Is it "normal" for postfix to take 60-90 ms for every email you send it? Or do I just have unreasonable expectations? I would expect the local postfix server to queue the email in about 20ms, tops!

  Read the article

• Is this a solution for having multiple SSL certificates on the same IP

  - by Saif Bechan

  I am running CentOS running on a VPS. I read some guides on having multiple SSL certificates on the same system, but I can not get the basics to work. The guide I got that makes the most sense to me is the doing the following. In CentOS I can make virtual NIC's. So I made 2 virtual NIC's to start with. 192.168.10.1, 192.168.10.2. Now I work in ISP manager Pro, so this is listening on my primary ip 1.1.1.1 For each website I have them listening on 192.168.10.1:80, 192.168.10.1:443 In the hosts file I made the following 2 entries 192.168.10.1 1st.com 192.168.10.2 2nd.com Now the strange thing is that when I browser to 1st.com I do not get the website located at 192.168.10.1, I get the website located at my prim IP 1.1.1.1 Should I do something like forwarding or routing for this setup to work? And the basic question: Will this setup even work? Are the SSL certificates based on the IP adress, or are the based on the host name, 1st.com and 2nd.com.

  Read the article

• ps aux as non-root doesn't show all processes

  - by JMW

  hi, i'm using an ubuntu 10.04 server... when i run ps aux as root i see all processes when i run ps aux as nonroot i see JUST the processes of the current user after a bit of research i found the following solution: root@m85:~# ls -al /proc/ total 4 dr-xr-xr-x 122 root root 0 2010-12-23 14:08 . drwxr-xr-x 22 root root 4096 2010-12-23 13:30 .. dr-x------ 6 root root 0 2010-12-23 14:08 1 dr-x------ 6 root root 0 2010-12-23 14:08 10 dr-x------ 6 root root 0 2010-12-23 14:08 1212 dr-x------ 6 root root 0 2010-12-23 14:08 1227 dr-x------ 6 root root 0 2010-12-23 14:08 1242 dr-x------ 6 zabbix zabbix 0 2010-12-24 23:52 12747 [...] my first idea was, that it got mounted in a weird way: /etc/fstab is ok and it doesn't seem to be mounted in an weird way... my second idea was, that there might be a rootkit: but it's not a rootkit... rkhunter tells me, that there is no rootkit installed... i don't know if it is since the machine got installed or came with an update. i've just installed zabbix-agent on the machine and realized, that it didn't work properly... What could have caused such strange permissions (500) and how can i set it back to an normal level (555) ? Crazy, i've never seen something like that... thanks in advance for any help and merry christmas :) see you

  Read the article

• Facing application redirection issue on nginx+tomcat

  - by Sunny Thakur

  I am facing a strange issue on application which is deployed on tomcat and nginx is using in front of tomcat to access the application from browser. The issue is, i deployed the application on tomcat and now setup the virtual host on nginx under conf.d directory [File i created is virtual.conf] and below is the content i am using for the same. server { listen 81; server_name domain.com; error_log /var/log/nginx/domain-admin-error.log; location / { proxy_pass http://localhost:100; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_set_header Host $http_host; } error_page 500 502 503 504 /50x.html; location = /50x.html { root html; } Now the issue is this when i am using rewrite ^(.*) http://$server_name$1 permanent; in server section and access the URL then this redirects to https://domain.com and i am able to log in to app and able to access the links also [I am not using ssl redirection in this host file and i don't know why this is happening] Now when i removed this from server section then i am able to access the application from :81 and able to logged into the application but when i click on any link in app this redirect me to the login page. I am not getting any logs in application logs as well as tomcat logs. Please help on this if this is a redirection issue of nginx. Thanks, Sunny

  Read the article

• 530 5.7.1 Client was not authenticated Exchange 2010 for some computers within mask

  - by user1636309

  We have a classic problem with Client not Authenticated but with a specific twist: We have an Exchange 2010 cluster, let's say EX01 and EX02, the connection is always to smtp.acme.com, then it is switched through load balancer. We have an application server, call it APP01 There are clients connected to the APP01. There is a need for anonymous mail relay from both clients and APP01. The Anonymous Users setting of the Exchange is DISABLED, but the specific computers - APP01 and clients by the mask, let's say, 192.168.2.* - are enabled. For internal relay, a "Send Connector" is created, and then the above IP addresses are added for the connector to allow computers, servers, or any other device such as a copy machine to use the exchange server to relay email to recipients. The problem is that the relay works for APP01 and some clients, but not others (we get "Client not Authenticated") - all inside the same network and the same mask. This is basically what we do to test it outside of our application: http://smtp25.blogspot.sk/2009/04/530-571-client-was-not-authenticated.html So, I am looking for ideas: What can be the reason for such a strange behaviour? Where I can see the trace of what's going on at the Exchange side?

  Read the article

• Anti Virus Service does not run - Windows XP SP3 32bit Home

  - by Stefan Fassel

  I have a somewhat strange problem here. I am trying to run Anti Virus Software on my Windows XP Home 32bit System. After a serious crash I had to fall back to an outdated copy of my initial installation and had Windows install 5 years of updates. So far so good. After Intalling a new Anti Virus Software (Bitdefender 2012) everything seemed to be fine, initial scanning went fine and configuration was working. But after restarting the System the Virus Scanner was unable to start up again. Even the Configuration console of the AV Software did not start. I tried scanning the System for malware, but nothing was found. Then I tried a different AV Software (MS Security Essentials), but in the end it did fail to start too. I have tried to start the Service manually, but I seem to be missing the privilege to do so. I am logged in as a Non-"Administrator" User with Admin privileges (Not much choices there on a XP Home System). I cannot switch to Administrator account outside the protected mode. When running Windows in protected mode I am unable to start the AV Software because it does not run in protected mode. I am a bit at loss now...

  Read the article

• Random Excel bug when referencing a different sheet

  - by Matteo

  I am getting a very strange error anytime I try to use a formula pointing to a cell in a different sheet from the active one (even as simple as "=Sheet2!A1"). This started happening all of a sudden, and without any change in the system - only I seem to having started having the problem since I started using a workbook from another colleague with the same issue. I'm running Excel 2003 SP3 on XP. With little variants, whenever I reference a cell in a different sheet, from any formula, and then press Enter, the formula gets written on a different cell from the one I was editing it in, and throws a REF error. Example: I start editing in cell A1 of Sheet 1, type "=", then move the cursor to cell B2 of Sheet 2 (that may contain any value), and press Enter. At this stage you would expect cell A1 in Sheet 1 to contain formula "=Sheet2!B2" and display the value in that cell. Instead what happens is that the cell remains empty, and another random cell of Sheet 1 gets populated with something like "=Sheet2!#REF!" throwing an error. Interestingly, the error does not happen when I manually type the cell reference in (ie. without moving the cursor to the second sheet). Hope this is making any sense - any ideas are welcome! Thanks.

  Read the article

< Previous Page | 566 567 568 569 570 571 572 573 574 575 576 577  | Next Page >