Search Results

Search found 19995 results on 800 pages for 'software updater'.

Page 581/800 | < Previous Page | 577 578 579 580 581 582 583 584 585 586 587 588  | Next Page >

• Is there a way to disable specific Spybot Immunization rules?

  - by Iszi

  I've been having problems using a desktop sharing application, which I've traced to the Immunization protections applied via Spybot S&D. Specifically, the problem has been narrowed down to the rules in the \SOFTWARE (Plugins) categories under the Internet Explorer groups. Once I disable these Immunization categories, everything in the application works fine. Each of these categories appears to include ~900 protections on the system. I suspect that the root cause of my problems could be narrowed down to just one, or perhaps a handful, of the settings that get applied in these categories. However, I can't find any options in Spybot S&D which would allow me to drill down to the individual protection rules and choose which to enable or disable. Is there something I'm missing, or is this not a feature available via the GUI? If it's not strictly supported in the application, is there a way to work around it by manually editing some of its files or registry settings? Spybot S&D version: 2.2.21.0 Spybot Start Center version: 2.2.21.129 Windows Ultimate x64

  Read the article

• Dell Upgrade to 12.04 LTS No wifi, graphic card driver and bluetooth Problem?

  - by Mattlinux1

  (Dell inspiron m5040 Upgrade to 12.04 LTS from 11.10 wifi wont work and has two bluetooth icons?) Old title of post! No Wifi/Bluetooth Problem. "Both Fixed", see below comments for bluetooth fix and see bottom answer for wifi fix. My online upgrade of 12.04 LTS, was installed to my laptop the Dell inspiron m5040, when it was done i found that my wifi did not even get picked up anymore and i now have two bluetooth icons at the top?? So what i have been doing for now is at the boot screen. I hit the use previous linux version, this works fine but also has the two bluetooth at the top. Is very thankful for any answers for this fix, Thank You. Ok bluetooth problem solved by – fossfreedom answer by deleting the other bluetooth program running in software center. Now the other problem is Wifi: just have to restart system as it works in previous linux version boot opt, but on the first boot screen opt run ubuntu it will not pick up wifi drivers. Broadcom 802.11 Linux STA wireless driverfor use with Broadcom's BCM4311-, BCM4312-, BCM4313-, BCM4321-,BCM4322-, BCM43224-, and BCM43225-, BCM43227- and BCM43228-basedhardware. And 3D-accelerated proprietary graphics driver for ATI cards. This driver is required to fully utilise the 3D potential of some ATI graphics cards, as well as provide 2D acceleration of newer cards. will not instill is there anyway for me to make a copy of the drivers via usb HDD and then put them on new upgraded version.

  Read the article

• How do I run a batch file async using PSExec?

  - by Paul Mrozowski

  I have a batch file I run that, among other things, reset's the NICs in the machine. I have some watchdog software running on another machine that monitors the first one. I'd like to run this batch file using PSExec when it detects certain types of failures. The problem I'm having is that since the batch file reset's the NIC's it kills the connection PSExec has (I'm OK with that). The real issue is that when PSExec dies the batch file stops running (leaving the NIC's disabled). I've tried using the -i option with PSExec with no luck. Any ideas about basically just fire off the batch file and NOT have it stop when PSExec is disconnected?

  Read the article

• How to adjust the appearance of the Unity in 12.10?

  - by piedro

  Now I updated to 12.10 and would like to adjust the desktop, well unity, appearance. I know there is the theme setting, but I cannot adjust the symbol theme or windows decoration with the systemsettings. I used to use the tool "unsettings" but it doesn't work with 12.10 anymore. Ubuntu Tweak used to be an option but at this point many features are broken and a lot of settings seem to mess up my system or they don't change anything at all (I understand that there has been a design settings change - gsettings, dconf, something ...) myunity has some options to change stuff but I couldn't find it for 12.10 ... not to forget "gnome-tweak-tool" which seems to work for most settings but not for all, e.g. it doesn't change the mouse cursor and the windows decorations do not show some decorations I'd like to use and I am also afraid of messing things up because it is supposed to be used in gnomeshell ... actually as I found out right now it really messes things up: fonts get inverted, suddenly high contrast accessibility setings are used in some windows, nautilus has white fonts on white background and even the login manager is a mess now ... So: How can I adjust the theme, symbol, decorations, fonts for the normal user and for the desktop and for the applications including the applications started as sudo user? I should mention that I upgraded from 12.04 and that some applications like synaptic completely ignore any settings ... sadly it is a mess, there was a time when gnome theming was really well done and very adjustable, I wonder what happened ... Just now I read that further development of Ubuntu Tweak has been stopped. The developer announced that he won't go any further with the software and the online services ... That is sad and destroys my hope for easy appearance editing just by waiting ... has been such a nice tool for 12.04 ... r.i.p.

  Read the article

• users unable to add registry keys to HKCU

  - by Eds

  I may not have this 100% correct so need some clarification. Are normal users on a 2003 terminal server allowed to add registry keys the their own HKCU section in the registry, or are they only allowed to edit existing ones? The reason I ask is that we have 3 keys that we need to add for each user on login. I thought it would be as simple as having a straightforward batchscript run that silently adds the keys for the user. Here is what I used: regedit.exe "C:\Documents and Settings\All Users\Desktop\example.reg" When the user runs this batch scipt, they see nothing as you would expect, but the keys are not added. If I simply run the .reg file as the user, it asks if I want to add the key, but then has an error saying there was an error accessing the registry. Do I need something a bit more complex to accomplish this task. Many Thanks Eds EDIT: Contents of .reg file Windows Registry Editor Version 5.00 [HKEY_CURRENT_USER\Software\Policies\Microsoft\office\14.0\outlook\Security] "PromptSimpleMAPINameResolve"=dword:00000002 "PromptSimpleMAPIOpenMessage"=dword:00000002 "PromptSimpleMAPISend"=dword:00000002

  Read the article

• How to reliably synchronise file servers between London and Shanghai?

  - by Andy S

  We have two offices, one in London and one in Shanghai, each needing to be able to access the same set of files. This means we need a solid, speedy means of synchronising a set of folders between servers at either office. They're likely to be Windows servers, but we could look at Linux boxes if the software side makes more sense on *nix. We've considered Rsync, Unison, Gluster, and a few other options, but none of them seem capable of reliably keeping the servers in sync between such distant office locations. Each office is on DSL connectivity over the open internet, so encryption is also a factor. Does anyone have any hints for getting the servers synchronising in as close to real time as possible, without dying constantly? Andy

  Read the article

• Is ZeroMQ a good choice to make a Python app and a C# managed assembly work together?

  - by Alex Bausk

  I have a task that involves talking to a .NET-based API (namely AutoCAD) to retrieve data, send commands, and react to events. I want to separate the API operations and the proper program logic (largely already implemented in Python) by using natural tools for both: a C# DLL for the former and a Python app for the latter. To connect these two pieces, I began exchanging JSON in ZeroMQ messages. I'm at early development stages but having recently discovered that ZeroMQ does not guarantee message delivery/order, I have reservations about whether this is a feasible way to go. Right now my app is a very basic REQ/REP pair and I plan to handle reacting to events and executing different commands by adding some sort of 'recipient-function' field to my message format. The reason that I want to use ZMQ is that I might be able to scale the software into a larger, multi-user, distributed solution sometime. I am a lay programmer so I would ask for your advice about this architecture. Should I just go ahead with it and plan to deal with message reliability/ordering when problems appear? Should I consider developing some kind of a REST wrapper around ZMQ?

  Read the article

• script to automatically test if a web site is available

  - by Xoundboy

  I'm a lone web developer with my own Centos VPS hosting a few small web sites for my clients. Today I discovered my httpd service had stopped (for no apparent reason - but that's another thread). I restarted it but now I need to find a way that I can be notified by email and/or SMS if it happens again - I don't like it when my client rings me to tell me their web site doesn't work! I know there are probably many different possibilities, including server monitoring software. I think all I really need is a script that I can run as a cron job from my dev host (which is permanently running in my office) that attempts to load a page from my production server and if it doesn't load within say 30 seconds then it sends me an email or SMS. I'm pretty rubbish at shell scripting, hence this question. Any suggestions would be gratefully appreciated, thanks to all you clever sysadmin guys and girls out there :)

  Read the article

• What should I do when my team leader is unfair for no reason? [closed]

  - by crucified soul

  I'm a new software developer and this is my first job. It's a startup and the CEO and the working environment is just great. I work really hard and I believe that I also do my job well. But recently, I have felt like my team leader is being unfair to me for no reason. It appears that he is nice to my co-workers, but not me. I figure he is mad at me, but I didn't bother to find out why. I really love this company and I really love working there. But if my team leader continues to be unfair then I have no option other than leaving. How can I fix this? EDIT: The other day he called me into his office and wanted to see my work in the afternoon (Yes, in my country, at summer season after 5PM is afternoon. My office begins at 8AM. And I'm not saying I've problems to work after 5PM). At the time I was facing a weird runtime error and I was pretty tired. I explained the situation to him. Then he found a small logical error in my code and asked me why I didn't fix this. I told him I was trying to resolve this runtime error and that I was sure that this logical error had nothing to do with the runtime error. He then proceeded to yell at me. After fixing the logical error that runtime error was still there. This is not the only occasion he has been unfair to me. I'm saying is being unfair because he doesn't do this kind of thing to other developers when they do really silly mistakes.

  Read the article

• Vacation scheduler/viewer

  - by Norfeldt

  I'm looking for a solution that allows multiple persons to put plan and notify their vacation by putting it in their electronic calendar and invite a dedicated "robot" email. On the other side I should be able to get a quick overview of the vacation for each person and do a print out that allows me to put it on a board. Example: John puts his winter vacation for week 7 into his calendar and invite [email protected]. Ben does the same thing for week 4 and 5 and invites [email protected]. Dilbert host the [email protected] and prints out and overview for the next 3 months. Each person's vacation is either stated by name or/and color on the print out. I would like to do the thing with standard business software like Outlook 2010 without installing too many softwares. But at the same time it should be easy and quick to make the print outs without too much fiddling Am I dreaming ?

  Read the article

• Sponsored Giveaway: Free Copies of WinX DVD Copy Pro for All How-To Geek Readers

  - by The Geek

  Have you ever wanted to make a backup of a DVD, or even rip it to an ISO file to use on your computer without the original optical disc? You can use WinX DVD Copy Pro to make this happen, and we’ve got a giveaway for all HTG readers. To get your free copy, just click through the following link to download and get the license code, as long as you download it by December 20th. In addition, an iPhone / iPad Video Software Pack will be presented as the second round gift from December 21st to January 2nd, 2013. For Windows users: http://www.winxdvd.com/giveaway/ WinX DVD Copy Pro has many features, including this list, which we copied straight from their site: Supports latest released DVDs. Protect your DVD disc from damage. Copy DVD to DVD, ISO image, etc. 9 advanced DVD backup schemes. Support Disney’s Fake, scratched DVDs and Sony ARccOS bad sector. Secure Yourself by Using Two-Step Verification on These 16 Web Services How to Fix a Stuck Pixel on an LCD Monitor How to Factory Reset Your Android Phone or Tablet When It Won’t Boot

  Read the article

• Computer suddenly won't boot - stops at a flashing prompt

  - by Dave M G

  I have been running Ubuntu on my computer for a long time, and I have been using 11.10 since it became available in October. Suddenly, this morning, when I rebooted, the computer would not reach the log in screen. I go through the standard POST boot sequence, and I also get a splash screen for my Nvidia graphics card, so at least most of the hardware seems to be working. After that, all I get is a flashing text prompt - one blinking white underline character on a screen that is otherwise completely blank. I don't think it is even reaching GRUB. No key input is possible. I have tried various key combinations to try and initiate some kind of interface, be it command line or anything else. The only key combination that works is [CTRL]+[ALT]+[Delete] to reboot. I realize this is likely to be a hardware problem, but it could be an Ubuntu problem(?), so I'm hoping for a specific set of troubleshooting steps so I can diagnose and repair this issue. My current suspicion is that one of the drives in my 2 disk software RAID has failed (even though they should be too new for that). However, this computer is critical to my work, so I'd like to invite advice on any possibilities so as to waste as little time as possible in fixing this machine.

  Read the article

• How can I troubleshoot SSD disconnection problems on Windows 7?

  - by 0xC0000022L

  I have a small SSD (Transcend StoreJet TS256GESD200K) which I am using on several computers. The drive is formatted with NTFS and recently I started noticing disconnects. Normally one probably wouldn't notice (you don't even get the notification sound in Windows when it disconnects), but since I use USBDLM and run a VM from that SSD, I get to see this first-hand. How could I best figure out whether the problem is the hardware (SSD, USB socket, USB cable or something in the PC) or software? In short: how can I locate the source of the disruption so that I can work on removing the problem? Side-note: SMART status for the SSD is clean.

  Read the article

• Discovery methods

  - by Owen Allen

  In Ops Center, asset discovery is a process in which the software determines what assets exist in your environment. You can't monitor an asset, or do anything to it through Ops Center, until it's discovered. I've seen a couple of questions about how to discover various types of asset, so I thought I'd explain the discovery methods and what they each do. Find Assets - This discovery method searches for service tags on all known networks. Service tags are small files on some hardware and operating systems that provide basic identification info. Once a service tag has been found, you provide credentials to manage the asset. This method can discover assets quickly, but only if the target assets have service tags. Add Assets with discovery profile - This method lets you specify targets by providing IP addresses, IP ranges, or hostnames, as well as the credentials needed to connect to and manage these assets. You can create discovery profiles for any type of asset. Declare asset - This method lets you specify the details of a server, with or without a configured service processor. You can then use Ops Center to install a new operating system or configure the SP. This method works well for new hardware. These methods are all discussed in more detail in the Asset Management chapter of the Feature Reference guide.

  Read the article

• Translating Documents from a Foreign Language into English on my Computer?

  - by Simon

  I am aware that websites can be translated from many languages into English thanks to Google Translate. If I receive documentation via email that is in a language other than English, how straight forward is it to translate into English on my PC or Apple Mac? (indeed is Google Translate involved or is it strictly for websites) Similarly if I receive documentation via the normal postal mail service (termed "snail mail" if I'm correct) which needs to be translated into English, what steps need to be taken for this documentation to be translated effectively & quickly on my PC or Apple Mac (I am aware of the term Optical Character Recognition (OCR) software, and is this costly, or do free alternatives exist to carry out the translation process solely online? ).

  Read the article

• Unity on Ubuntu 11.10 - The Dash Home button brings up the panel, but is empty

  - by David M. Coe

  The dash home button brings up a panel that is greyed out, but it is totally empty. It seems to be the very same issue as this: Dash home button brings up blank window which is unanswered. /usr/lib/nux/unity_support_test -p returns OpenGL vendor string: X.Org R300 Project OpenGL renderer string: Gallium 0.4 on ATI RV370 OpenGL version string: 2.1 Mesa 7.11 Not software rendered: yes Not blacklisted: yes GLX fbconfig: yes GLX texture from pixmap: yes GL npot or rect textures: yes GL vertex program: yes GL fragment program: yes GL vertex buffer object: yes GL framebuffer object: yes GL version is 1.4+: yes Unity 3D supported: yes I've tried a unity --reset but that doesn't seem to work. Unity seems to reset, but I get the following warning over and over: cs space validation failed unity What should I do next to try and fix this? Edit: Attempted fixes: I've refomatted, did not work. I've done apt-get remove unity then apt-get update then apt-get install unity, did not work. I've switched to Unity 2d and this seems to work. How can I get regualar Unity working or atleast find the error?

  Read the article

• What does Libre Office do to an existing Excel sheet to bloat its size?

  - by Sn3akyP3t3

  I try to avoid using Libre Office on existing Excel created workbooks because of the potential for unpleasant results. In this case Libre Office bloated the size of the workbook for some reason unknown to me. I would like to know if Libre Office does this to all Excel workbooks or just something in that workbook that causes it. Software involved: Microsoft Office Excel 2010 Libre Office 3.5.x (exact version unknown) Dropbox (merely to sync changes) Platforms involved: Office on Windows (master of the obvious on that one I suppose..) Libre Office on Mac OS 10.6 Types of data stored in this workbook: Text Integers 1 column with a simple formula spanning the entire worksheet representing that particular row (=CONCATENATE(A2285,B2285,D2285), =CONCATENATE(A2286,B2286,D2286), etc.) Total of 3,500 plus rows Here is a photo with details described within, but I'll go ahead and explain the photo as well: This screenshot is from Dropbox history of the .xlsx workbook. Version 61 - 68 were Office Excel. Version 69 - 73 were Libre Office.

  Read the article

• Sample domain model for online store

  - by Carel

  We are a group of 4 software development students currently studying at the Cape Peninsula University of Technology. Currently, we are tasked with developing a web application that functions as a online store. We decided to do the back-end in Java while making use of Google Guice for persistence(which is mostly irrelevant for my question). The general idea so far to use PHP to create the website. We decided that we would like to try, after handing in the project, and register a business to actually implement the website. The problem we have been experiencing is with the domain model. These are mostly small issues, however they are starting to impact the schedule of our project. Since we are all young IT students, we have virtually no experience in the business world. As such, we spend quite a significant amount of time planning the domain model in the first place. Now, some of the issues we're picking up is say the reference between the Customer entity and the order entity. Currently, we don't have the customer id in the order entity and we have a list of order entities in the customer entity. Lately, I have wondered if the persistence mechanism will put the client id physically in the order table, even if it's not in the entity? So, I started wondering, if you load a customer object, it will search the entire order table for orders with the customer's id. Now, say you have 10 000 customers and 500 000 orders, won't this take an extremely long time? There are also some business processes that I'm not completely clear on. Finally, my question is: does anyone know of a sample domain model out there that is similar to what we're trying to achieve that will be safe to look at as a reference? I don't want to be accused of stealing anybody's intellectual property, especially since we might implement this as a business.

  Read the article

• Linux: disbale USB without disabling power

  - by Ergot

  TLDR I want toggle between the following usages of a usb-port via the terminal: use like a normal usb-port only supply energy to charge Story I recently got me something like a magna doodle that can save your drawings to pdf, which can be moved to your computer via usb afterwards. Now the thing is that you can't save anything while it's plugged in. Because it's the only way to charge it, it bugs me that I can't find a software solution and laziness I want to keep it plugged in and toggle the connection to the computer only when needed. I noticed that it's charging and usable when it is plugged in and the computer is shut down or suspened. So I guess that there's a way to do it. Tech info computer: ThinkPad X201 Linux Kernel: 3.14.5-1-ARCH "Magna doodle": Boogie Board Sync

  Read the article

• Xen and Ubuntu?

  - by wag2639

  How does one properly approach having Ubuntu servers on a Xen hypervisor? I don't have any experience with RAID or Xen other than from a theoretical level. Additional requirements: Use with mdadm Software RAID 5 (can be on separate disks) that multiple instances with access Paravirtualized Ubuntu Server guests instances Possible ideas for now: Ubuntu host (dom0) with ubuntu-xen-server package (this purportedly isn't supported) dom0 host will "own" RAID 5 partition More Ubuntu servers as guests Citrix XenServer bare-metal host XenServer will own RAID Citrix XenServer bare-metal host Ubuntu guest instance creates and owns RAID Questions and concerns: Can Ubuntu be used as a dom0 Xen host? Can XenServer install packages such as mdadm and create a partition? Can multiple guest access (R + W) to the same data partition (RAID)? Note: since it may have a bearing on support, I'm referring to Ubuntu Server 10.04

  Read the article

• How to Manage and Use LVM (Logical Volume Management) in Ubuntu

  - by Justin Garrison

  In our previous article we told you what LVM is and what you may want to use it for, and today we are going to walk you through some of the key management tools of LVM so you will be confident when setting up or expanding your installation. As stated before, LVM is a abstraction layer between your operating system and physical hard drives. What that means is your physical hard drives and partitions are no longer tied to the hard drives and partitions they reside on. Rather, the hard drives and partitions that your operating system sees can be any number of separate hard drives pooled together or in a software RAID Latest Features How-To Geek ETC Inspire Geek Love with These Hilarious Geek Valentines How to Integrate Dropbox with Pages, Keynote, and Numbers on iPad RGB? CMYK? Alpha? What Are Image Channels and What Do They Mean? How to Recover that Photo, Picture or File You Deleted Accidentally How To Colorize Black and White Vintage Photographs in Photoshop How To Get SSH Command-Line Access to Windows 7 Using Cygwin How to Kid Proof Your Computer’s Power and Reset Buttons Microsoft’s Windows Media Player Extension Adds H.264 Support Back to Google Chrome Android Notifier Pushes Android Notices to Your Desktop Dead Space 2 Theme for Chrome and Iron Carl Sagan and Halo Reach Mashup – We Humans are Capable of Greatness [Video] Battle the Necromorphs Once Again on Your Desktop with the Dead Space 2 Theme for Windows 7

  Read the article

• Multicasting Windows 7 Image

  - by LawnChairSkank

  I am trying to deploy some new machines with windows 7 for the first time in our computer labs. We used to use third party imaging software and then run sysprep after the image was copied(XP), but it seems you can't go that route with windows 7. We set up a new imaging server with the windows system image manager, but when we try to multicast the image it pretty much takes down our whole staff and faculty network. I heard you can turn on a multicast feature on our cisco switches to help with the issue, but that it also slows the switches to a crawl. Another idea we have tried was pulling the the computer lab switch off the main network and plugging the imaging server directly into the computer lab switch so the multicast doesn't take down our network, but it doesn't seem to work without being able to hit a domain controller. Is there a way to multicast without taking out the network? I feel like I am missing something... Thanks in advance

  Read the article

• Windows 7 wifi reports "no network access" and "no internet access" but connects in fedora

  - by rick2047

  I am running windows 7 home basic (64bit) on a Acer 5742G laptop with Atheos wifi adapter in it. Yesterday, I hiberneted my computer as I always do and up untill then the wifi was working fine. When I booted my computer up again today I started having a strange problem: It detects my wifi but after connecting to it, it keeps on oscillating between states of no network access and no internet access. I can't connect to anything (the internet or my router). I tried to reset my internet protocol stack using this fixit file. I also tried to uninstall and reinstall my network driver. Neither helped. I am using the same laptop's fedora installation right now and the wifi is working perfectly fine. Please help. Edit To add additional details, I have Microsoft Security essentials as my antivirus software and I haven't messed with the firewall or the router configurations.

  Read the article

• Filtering serial port io

  - by mr odus

  I am currently working on a project where I communicate with hardware via a com port on its respective pc(win xp or 7) It is a fairly large project and sifting through the log file can be a bit of pain. This is my current setup. I use putty to do the actual serial communication, and write it to a log file. Then using MinGW Msys I filter it using tail -f "puttyLog" | grep -i "search term" Is there a better way to do this? I mean specifically filtering the input in realtime. Not that mine is terrible, but it still involves having to read from a log and sometimes there have been hangups where it will be delayed for a minute or 2. I have used software in the past with a main io window and then internal filter panels, but can no longer remember or find it.

  Read the article

• Lock Windows keyboard and mouse but still display screen normally

  - by Stephen Lacy

  I'm using windows 7, I have a dual monitor display. It displays important information related to the business, I'd rather that random users that walk in can't just walk over to it and start using the computer with the same access rights as the user the monitoring software is running as. What I would like is if any time someone presses a button on the keyboard including alt-ctrl-delete all that would appear is a dialog asking for a password. Then I can click cancel and it will return to showing the data I want displayed. ClearLock doesn't work I tried it btw

  Read the article

< Previous Page | 577 578 579 580 581 582 583 584 585 586 587 588  | Next Page >