Search Results

Search found 17148 results on 686 pages for 'screen coordinates'.

Page 583/686 | < Previous Page | 579 580 581 582 583 584 585 586 587 588 589 590  | Next Page >

  • Blinking power button

    - by Mike Ramsey
    A friend asked me to look at his Gateway DX4640 desktop. When he presses the power button, power goes to the mobo (NVIDIA nForce 630i MCP73PV, GeForce 7100 chipset) and the CPU fan starts spinning. The power button slowely blinks on and off (blue) and the screen briefly says no signal and then goes black. And nothing else; no post code beeps. My initial two conjectures were: 1. Vista was stuck in sleep/hibernation mode, or 2. A power off had left the mobo in a bad state. The fix for both is to: a) Unplug the AC power cord b) hold the power button for 30 second to fully discharge the mobo It didn't help. I left the system unplugged from AC power for an hour. No change. I am out of ideas. Has anybody seen anything like this before? What does a blinking blue power button mean? How can I get more data points to guide trouble shooting? --Thank you, --Mike

    Read the article

  • a disk read error occurred

    - by kellogs
    Hi, ¨a disk read error occurred¨ appears on screen after choosing to boot into Windows XP from GRUB. [root@localhost linux]# fdisk -lu Disk /dev/sda: 160.0 GB, 160041885696 bytes 255 heads, 63 sectors/track, 19457 cylinders, total 312581808 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x48424841 Device Boot Start End Blocks Id System /dev/sda1 63 204214271 102107104+ 7 HPFS/NTFS Partition 1 does not end on cylinder boundary. /dev/sda2 204214272 255606783 25696256 af HFS / HFS+ Partition 2 does not end on cylinder boundary. /dev/sda3 255606784 276488191 10440704 c W95 FAT32 (LBA) Partition 3 does not end on cylinder boundary. /dev/sda4 276490179 312576704 18043263 5 Extended /dev/sda5 * 276490240 286709759 5109760 83 Linux /dev/sda6 286712118 310488254 11888068+ b W95 FAT32 /dev/sda7 310488318 312576704 1044193+ 82 Linux swap / Solaris sda is a 160GB hard disk with quite a few partitions and 3 OSes installed. I am able to boot into Linux and Mac OS fine, but not into Windows anymore. The Windows system is located on /dev/sda1. I can not recall how exactly have I used testdisk but it once said that ¨The harddisk /dev/sda (160GB / 149 GB) seems too small! (< 172GB / 157GB)¨ or something simillar. So far I have tried to ¨fixboot¨ and ¨chkdsk¨ from a recovery console on the affected windows partition (/dev/sda1), the plug off power cord for 15 seconds trick, reinstalling GRUB, repairing the MFT and boot sector of the affected partition via testdisk, what next please ? Thank you!

    Read the article

  • Reducing video mode switching during Linux boot

    - by Zack
    When I boot up my desktop computer, which only has Linux on it, the video mode and/or console font gets switched four times: When GRUB starts, it switches from 80x25 text to a graphical mode so it can draw a pretty background behind its menu; GRUB then goes back to 80x25 text after I pick something from the menu; When the KMS driver for my video card loads, it switches to a much higher-resolution text mode (I don't know if this is a hardware text mode or not); Finally X starts and it goes graphics and stays that way. I think this last switch does not change the resolution of the video mode, only the graphicalness. I'd like to get rid of as many of these mode switches as possible. Ideally, when GRUB takes over from the BIOS it would go directly to the same high-resolution text mode that the KMS driver selects, and the display would stay in that mode till X starts and brings up graphics. I am under the impression that this is possible by mucking with the kernel command line and/or the GRUB console module load parameters, but I don't know the details. GRUB 1.98+20100706, kernel 2.6.32.15 using Nouveau video drivers. Distro is Debian unstable. Please no answers that involve recompiling anything or cobbling together bleeding-edge kernel/driver combinations, I don't care enough about this to go to that much trouble. EDIT: Tobu suggests setting GRUB_GFXMODE to the full pixel resolution of the monitor, and GRUB_GFXPAYLOAD_LINUX=keep to avoid the mode switch after the menu goes away. This does part of what I want, but winds up being worse overall. There's no mode switch after the menu, but there's still a painfully-slow screen repaint (I should probably just give up on GRUB's gfxmode, it's waaaay too slow at 1920x1200). More seriously, there's now a double mode switch when nouveaufb loads, along with fun-looking error messages in dmesg [ 5.923798] [drm] nouveau 0000:02:00.0: allocated 1920x1200 fb: 0x40250000, bo ffff8801ba5f4600 [ 5.923802] fb: conflicting fb hw usage nouveaufb vs EFI VGA - removing generic driver [ 5.923821] [drm] nouveau 0000:02:00.0: PFIFO_INTR 0x00000010 - Ch 1 ("PFIFO_INTR" message repeats 400+ times) [ 5.925609] Console: switching to colour dummy device 80x25 [ 5.925802] Console: switching to colour frame buffer device 240x75

    Read the article

  • Acer LCD says "no signal"

    - by Ken
    I have an Acer 24" LCD (model "AL2423WDR") that's about 3 years old. It worked perfectly for most of its lifetime so far. Recently it started giving problems. When I turn it on, it either says "no signal" on the display, or the power light goes yellow (as if in power-saving mode). This happens with both DVI and VGA (both of which worked fine before), and stranger still, the 4 buttons on the front, for accessing the on-screen menus, don't do anything. I've also tried different computer hardware and software (PC/Mac, Linux/MacOS), but nothing has worked. I've tried power-cycling it (with both the power button and the power switch), and also unplugging it entirely. The nonworking buttons suggest to me an issue with the firmware. I found a place on Acer's website that says I can send it in to have it fixed, at my expense, but I'll avoid that if I can. Is there a way to fully reset it manually? Or is there something else I can try?

    Read the article

  • NVIDIA GeForce GT750M drivers for Ubuntu 13.10 on iMac

    - by Eugene B
    I have just got a new iMac 14.3 with 21.5' display. It has Intel i7 processor and NVIDIA GeForce GT750M graphics card with GPU (Device ID: 0x00fe9). I have installed Ubuntu 13.10 on it (dual boot with refit). Everything works fine apart from graphics. It is clear that graphics' not accelerated, and there are no drivers suggested in the "Additional drivers" section. I have tried to Install nvidia drivers from the repository. Download nvidia drivers and install them manually. Follow instructions here. Follow instructions here. Follow instructions here. Install bumblebee. Play around with xorg.conf file. Blacklist nouveau. As you may guess, nothing worked. The weirdest thing is, that when I boot from a LiveCD, it picks up screen resolution and all the rest correctly, though when I install the system to my Hard Drive it clearly does not have proper drivers. Does anyone have any suggestion what to do?

    Read the article

  • Media Center setup won't complete for watching TV

    - by Robert
    I have a problem watching TV in Media Center. The TV constantly pauses 1/2 second then plays 1 second, pauses 1/2 second, plays 1 second - it is constant and does not vary. This problem occurs on all channels, live or recorded. The bottom 5th of the screen is solid green. I know the problem is Media Center because I can use Pinnacle's TVCenterPro to watch TV and there is no skipping/pausing (and not green on bottom). I was using cable, and switched to DirecTV (satellite). Trying to do "Set up TV signal" in Media Center seems to be what broke it. I get an error "IR Hardware not detected." I can use the remote to "try again" - so the IR hardware works fine (Media Center's remote/sensor). I tried plugging the IR Blaster into both ports, and I tried a different USB port for the IR receiver. I can't complete the setup. Media Center was playing TV okay (with the new DirecTV) before I tried to run setup. (I ran setup to try to do recording with Media Center.) Hardware/Software: Pinnacle PCTV 800i HD PCI card (coax cable from DirecTV tuner), ATI Radeon HD 3200 Graphics, Windows XP SP3 Media Center Edition, AMD Athlon Dual Core 2.5 GHz, 1.75 GB RAM.

    Read the article

  • CentOS 5.5 remote kickstart installation stalls at "Starting install process." How to debug?

    - by ewwhite
    Hello, I'm having a difficult time with a remote CentOS 5.5 kickstart installation on an HP ProLiant DL360 G6. This is in an environment where I maintain an internal CentOS yum repository. The kickstart installation and post scripts have been tested and normally work. This hardware is also common in this environment, so I do not believe that it is a factor. Unfortunately, I'm having problems with a specific server install. The system is remote to the yum repository at a distance of 500 miles. They are connected over a private low-latency 100-megabit layer 2 connection (26ms round-trip). I'm mounting the 10mb CentOS 5 netinstall ISO image via an HP ILO remote console. The initial boot parameters are: linux ks=http://yum.abctrading.com/prop.cfg ksdevice=eth0 ip=x.x.x.x dns=x.x.x.x netmask=255.255.255.0 gateway=x.x.x.x I'm using the url --url http://ks.abctrading.com/5.5/os/x86_64/ method of installation. This quickly boots into the anaconda installer, pulls the kickstart config and formats the drives. The process eventually halts at the screen below, reading "Starting install process.". Going to the other virtual consoles give the second image below. The process stalls at this point and cannot proceed with the rest of the installation. Running the same kickstart config locally works just fine. I've tried mounting the boot ISO from the console as well as from the ILO2 command line pointing to a locally-hosted boot ISO via http. How can I debug this? Are there any options I've overlooked?

    Read the article

  • Recover NTFS data from a ZFS pool that was exposed as an iSCSI target

    - by David
    This was me being stupid and the data is by no means critical and is now a learning experience first, time saver second. I set up a 100GB iSCSI target via the bare bone instructions in napp-it. It's a volume LU. I then had my Windows 7 machine connect to the iSCSI target, formatted it to NTFS, and tested the performance of it with some large iso file transfers. I then unmapped the drive, reconnected to the target, and was forced to format to NTFS again. It was then I realized the files I had transferred only existed on the iSCSI target. I threw a little fit and then went about my business. When I was cleaning up my experiment I noticed in this screen: http://imgur.com/1xlcu.jpg That is my experimental target tank/iSCSI and it still has a lot of data in it. Assuming my isos are still in this pool how would I go about recovering them? While writing this I used GetDataBackup for NTFS from www.runtime.org. And while it found two previous NTFS partitions there was no data.

    Read the article

  • How do I use a Minitel terminal as a linux dumb terminal

    - by Pawz
    I recently purchased a US version of the Alcatel Minitel terminal. I think it's a 1B version. Pictures of it here: I tried connecting a null modem to the 25 pin port on the back and plugging it into a linux box running agetty but I couldn't get it to show any signs of being connected. I used Google Translate to translate this document into English: http://mirabellug.org/wikini/upload/Documentations_minitel.pdf As far as I can tell, you take it out of videotex mode by typing Fcnt-T A, then turn off local echo with Fcnt-T E, then set it to 4800 baud with Fcnt-P 4. I presume Fcnt refers to the "CTRL" key on my terminal. But I think I'm doing something wrong, because it doesn't look like it's recognising the keystrokes, because "Fcnt-T A" just prints the letter A to the screen, which is not what you'd expect a function key combo to do. Has anyone used these minitel terminals as a linux terminal, and if so, please can you share how to configure the minitel to run as a terminal ? Is the 25 pin plug even the correct port to use ? I read something online that indicated you're supposed to use the 5 pin DIN plug instead, is that right ? If so, what's the 25 pin plug for ? If I am supposed to use the DIN plug, does anyone know the pinouts so I can make a cable ?

    Read the article

  • Can I disable this Windows (XP) Security Warning?

    - by FumbleFingers
    I recently reformatted my hard drive and reinstalled Windows XP (I know I'll have to take the plunge and commit to Win8 "real soon, now", but I'm just not quite ready for the upheaval yet! :) I used to use WinRar (and later, when I got fed up with the "nag" messages, 7-Zip), but I haven't installed either of them in my new configuration, so I must be using the built-in XP facility when I open *.zip files. For years, I've been opening downloaded *.zip archives, and using "drag & drop" to copy to a File Explorer window open on the folder where I want the files to end up (usually, My Documents\Downloads). But now I find that when I "drop" the file(s), I get a pop-up Windows Security Warning saying Are you sure you want to copy or move files to this folder? You should only move or copy files from locations that you trust Can anyone explain why I'm getting this message, and is there any (reasonably easy, please! :) way to suppress it? Since I've already put the *.zip file on my computer, it seems a bit late to ask if I trust it. (Thus far, the files in question have always been plain text, so it's not a matter of dodgy programs, etc.) Apologies for the low quality image - I don't have the appropriate tools or knowledge to do any better, and it doesn't help that my "PrtScr" screen capture has included what would have been on my second monitor (TV) if it had been turned on. If you can't read it, trust me - I have copied the text verbatim.

    Read the article

  • Authenticate VNC session with ConsolKit?

    - by lori
    I have a linux machine running Fedora 16 in a cupboard. It has no screen or keyboard. I connect to it using a combination of vnc and ssh. Recently, after an update, I have had issues with authentication on the machine. If I vnc to it, the kde desktop pops up an error dialog every few minutes saying Authorization failed. Failed to obtain authentication. If I plug in a USB drive it fails to mount, Dolphin reports an authentication issue again. I have had limited success finding the solution. AFAICT, it is an issue with ConsoleKit deeming me to be a non-local user so it prevents authentication. This is the output from ck-list-sessions: $ ck-list-sessions Session5: unix-user = '1000' realname = 'steve' seat = 'Seat6' session-type = '' active = FALSE x11-display = ':1' x11-display-device = '' display-device = '' remote-host-name = '' is-local = FALSE on-since = '2012-09-16T08:07:03.137011Z' login-session-id = '1' I have tried to update my .vnc/xstartup script to include ck-launch-session as follows: $ cat ~/.vnc/xstartup #!/bin/sh exec ck-launch-session vncconfig -iconic & unset SESSION_MANAGER unset DBUS_SESSION_BUS_ADDRESS export XKL_XMODMAP_DISABLE=1 OS=`uname -s` if [ $OS = 'Linux' ]; then case "$WINDOWMANAGER" in *gnome*) if [ -e /etc/SuSE-release ]; then PATH=$PATH:/opt/gnome/bin export PATH fi ;; esac fi if [ -x /etc/X11/xinit/xinitrc ]; then exec ck-launch-session /etc/X11/xinit/xinitrc fi if [ -f /etc/X11/xinit/xinitrc ]; then exec ck-launch-session sh /etc/X11/xinit/xinitrc fi [ -r $HOME/.Xresources ] && xrdb $HOME/.Xresources exec ck-launch-session xsetroot -solid grey exec ck-launch-session xterm -geometry 80x24+10+10 -ls -title "$VNCDESKTOP Desktop" & exec ck-launch-session twm & This has not helped. How can I either authenticate myself to ConsoleKit, or trick it into believing I am a local user?

    Read the article

  • Performance experiences for running Windows 7 on a Thin-Client?

    - by Peter Bernier
    Has anyone else tried installing Windows 7 on thin-client hardware? I'd be very interested to hear about other people's experiences and what sort of hardware tweaks they had to do to get it to work. (Yes, I realize this is completely unsupported.. half the fun of playing with machines and beta/RC versions is trying out unsupported scenarios. :) ) I managed to get Windows 7 installed on a modified Wyse 9450 Thin-Client and while the performance isn't great, it is usable, particularly as an RDP workstation. Before installing 7, I added another 256Mb of ram (512 total), a 60G laptop hard-drive and a PCI videocard to the 9450 (this was in order to increase the supported screen resolution). I basically did this in order to see whether or not it was possible to get 7 installed on such minimal hardware, and see what the performance would be. For a 550Mhz processor, I was reasonably impressed. I've been using the machine for RDP for the last couple of days and it actually seems slightly snappier than the default Windows XP embedded install (although this is more likely the result of the extra hardware). I'll be running some more tests later on as I'm curious to see particularl whether the streaming video performance will improve. I'd love to hear about anyone's experiences getting 7 to work on extremely low-powered hardware. Particularly any sort of tweaks that you've discovered in order to increase performance..

    Read the article

  • Rebuild Fedora 19 ISO adding Kickstart for USB install

    - by dooffas
    I am attempting to edit a Fedora 19 DVD ISO to add a kickstart file. I then need this ISO burnt to a USB stick for instillation. The error I get when booting is Warning: Could not boot. Warning: /dev/root does not exist To try and determine which part of the process is failing I have broken the process down in to separate stages. Step 1: Burn the original ISO "Fedora-19-x86_64-DVD.iso" (Available - here) to a pendrive and see if that will install. dd if=/path/to/iso of=/dev/sdc Burning this image was successful and it installed without issue. Step 2: Exctract the ISO, repackage it and burn it to a pendrive and see if that will install. PLEASE NOTE: The final command in this section has been broken down in to multiple lines for ease of reading, in fact it was run as a single command on one line. mkdir -p /mnt/linux mount -o loop /tmp/linux-install.iso /mnt/linux cd /mnt/ tar -cvf - linux | (cd /var/tmp/ && tar -xf - ) cd /var/tmp/linux xorriso -as mkisofs -R -J -V "NewFedoraImage" -o ouput/file.iso -b isolinux/isolinux.bin -c isolinux/boot.cat -no-emul-boot -boot-load-size 4 -boot-info-table -isohybrid-mbr /usr/share/syslinux/isohdpfx.bin . This iso was then burnt to a pendrive as before. dd if=/path/to/iso of=/dev/sdc This ISO burnt to the pen drive with no problem and will boot. I then see the fedora options screen. After choosing either "Install Fedora 19" or "Test this media & install Fedora 19" I then receive the errors highlighted above. This means the kickstart file is not to blame, but repackaging the ISO. Is there something I am missing in the repackaging process? Any input would be great! NOTE: If it is of any help, I attempted Step 2 with an Ubuntu server ISO and the process was successful.

    Read the article

  • iptables, blocking large numbers of IP Addresses

    - by Twirrim
    I'm looking to block IP addresses in a relatively automated fashion if they look to be 'screen scraping' content from websites that we host. In the past this was achieved by some ingenious perl scripts and OpenBSD's pf. pf is great in that you can provide it nice tables of IP addresses and it will efficiently handle blocking based on them. However for various reasons (before my time) they made the decision to switch to CentOS. iptables doesn't natively provide the ability to block large numbers of addresses (I'm told it wasn't unusual to be blocking 5000+), and I'm a bit cautious over adding that many rules into an iptable. ipt_recent would be awesome for doing this, plus it provides a lot of flexibility for just severely slowing down access, but there is a bug in the CentOS kernel that is stopping me from using it (reported, but awaiting fix). Using ipset would entail compiling a more up-to-date version of iptables than comes with CentOS which whilst I'm perfectly capable of doing it, I'd rather not do from a patching, security and consistency perspective. Other than those two it looks like nfblock is a reasonable alternative. Is anyone aware of other ways of achieving this? Are my concerns about several thousand IP addresses in iptables as individual rules unfounded?

    Read the article

  • Alternative software for Pinnacle PCTV 100e

    - by Stijn Sanders
    I have a Pinnacle PCTV 100e external USB cable television receiver. I've been using Pinnacle's software that came with the card (TVCenter Pro) to record things at given times. Things I don't like is an extremely high CPU load, and that it doesn't seem to halt the screensaver from running when watching in full screen. Also, I was away the last two weeks, and the schedules went terribly bust. Some items were recorded hours before or after the actual scheduled time (and now I missed some shows), and some recurring schedules weren't converted into the next occurrence correctly! Is there good alternative software that would work with my PCTV 100e? (Preferalby cheap or free) I've tried VLC Player, which gets video, but no audio. I've tried MediaPortal, which crashes when trying to scan for channels. When I select a channel manually, the stored mpg has big errors in encoding and is also missing audio. There's VirtualDub, but that doesn't have ready-made scheduled-recording options. This I can conjure some scheduled scripts for, but I've noticed the sync gets awfully wrong after some time. I've tried Windows Media Center, but it doesn't seem to support the PCTV 100e.

    Read the article

  • Free/opensource application for charting stock prices?

    - by Homunculus Reticulli
    I am looking for a free or FOSS software application for SIMPLY charting stock prices. I am not interested in any of the other nonsense typically bundled with such packages (technical analysis, back testing, tracking etc, etc). All I want to do is the following: Import file from CSV and plot on the chart Ability to scroll the chart left/right (zoom feature would be nice to) Ability to draw straight line (between 2 points) on the plot Ability to plot the graph for different resolutions (for e.g weekly, monthly - or some other custom resolution that I want) print the displayed graph (I can always use screen capture if printing is too much to ask) Thats all I want to do. I am not interested in anything else. I would have thought I could have found something by now. I would have written my own tool (I still will do that at a later stage), but I am a bit short of time at the moment, so I just want something that will do all of the above. Can anyone recommend a package. Last but not the least, I am running on Linux (and would prefer to do so - BUT if I have to, I can run on ahem - you know, Windows)

    Read the article

  • GA 8KNXP Rev1.0: 4 GB installed, only 3.5 GB recognized by BIOS

    - by hurikhan77
    I've installed 2x 1 GB and 4x 512 MB memory into my GA-8KNXP system which would sum up to 4 GB. The specification from the manual says: Maximum memory support: 4 GB. If all six slots are utilized, slot 5+6 may only equipped with single-sided RAM modules. And so I did. Anyway: The BIOS counts up to 3.5 GB and finishes there. Also my Linux system reports only 3.5 GB of memory although 4 GB memory support is activated in the kernel. So I suppose this is a memory mapping issue or a hardware issue. I've tried removing only on of the 512 MB memory modules leaving 5 modules in place. But that just stopped the system from powering on correctly (screen stays black although fans and leds come to live). Dual Channel was detected and enabled so the system technically found all 6 modules. "dmidecode" in Linux reports only memory in slots 1 to 4 and ignores slots 5+6, so it only detects 3 GB of memory. It also says the system would support up to 16 GB of memory with 4 GB modules per slot. I think technically the chipset should be able to offer and utilize the complete 4 GB memory range. Any clues what else I could check? Or do I have just to live with 0.5 GB wasted memory?

    Read the article

  • Video output vanishes and it isn't the video card... suggestions?

    - by Ira Baxter
    I have a high-end dual processor Dell workstation that operated for several years without problem. Recently, the video output has gone flaky, in the sense that after 2-3 days, it loses synch with the monitor (sometimes you can still see a hashed-mess of the what you expect to see on the screen). Poking at the keyboard, and accessing the file system on the machine from over the network, indicates that the machine is running fine and its just the video. A reboot fixes the problem... for another day or two. This in effect makes the machine unusable. So, I replaced the video card with an exact duplicate bought from e-bay. (I checked after the dupe arrived to be sure, yep, same model number). I still get the same behavior. So unless I believe that both video cards are broken the same way, I have to beleive this is a problem with the motherboard/power supply, neither of which I am inclined to replace. The only other possibility I can think of is a Windows update to the graphics driver. How would I check for this? Anybody had a similar problem? Otherwise we're junking what used to be a perfectly good machine. (Another couple of hours of more wasted effort and that's it in terms of economics anyway).

    Read the article

  • Keyboard's media keys are blocked by a program

    - by Mike Hanson
    I've got a Microsoft Natural Ergonomic Keyboard 4000. In addition to the regular keys, it's also got keys for Web/Home, Search, Mail, Favorites (5), Calculator, and Media functions (Mute, Volume Up/Down, and Play/Pause). Everything works most of the time, and the exception is rather odd. I use a programming system called Clarion. When that has focus, the Media keys don't work. (All the others still do.) I've also discovered that programs that I create using Clarion also block the media keys (only when they have focus). This indicates that it's probably something in Clarion's Run-Time Library (RTL) that's causing the trouble. The keys will work if I click on a non-Clarion window before hitting the media key, but that's an undesirable hassle. The odd thing is that I have many colleagues with the same keyboard, and they have no problem. When I recently upgraded from Vista Professional to Win7 Ultimate, I noticed that various things "appear" differently. For example, with my old system, when I changed the volume or muted the volume bar visualization always appeared at the bottom right on the screen. Now it doesn't appear in certain programs, even when it works. This indicates an order of precedence for visual elements. I'm fairly certain a similar order of precedence exists for keyboard hooks. Depending on how the hooks are defined, and the order in which they're applied, it would seem that sometimes the IntelliType drivers don't see the media keystrokes. The Media keys probably behave differently than the rest of the "special" keys, because they are more of a standard across all keyboards, so perhaps are handled by a different driver hooking mechanism. Does anyone have any suggestions of how I might fix this problem? Is there some way to change the order of hooks? Delay the loading of the IntelliType driver? Thanks in advance!

    Read the article

  • Windows 8 Doesn't Shutdown Properly With Fast Start-Up Enabled

    - by Patrick
    While Fast start-up is enabled, on turning the computer off (shutdown) the computer idles for about 5min after logging out/screen turning off. It then turns off. On returning into Windows I receive the error message saying Windows didn't shut down properly. Hibernate works fine, and I am told this shouldn't be the case - If one doesn't work, neither should. It works when both Fast start-up is enabled and disabled, as does restart and sleep. Windows is installed under UEFI. The UEFI ultra fast boot option for my motherboard cannot be enabled as my GPU doesn't support some UEFI GOP tech. As far as I know, not related to windows fast start-up, but thought it was worth mentioning. To clarify, if this: http://www.eightforums.com/tutorials/6320-fast-startup-turn-off-windows-8-a.html is enabled, the computer does not shut down properly. EDIT: Some more information on the matter: Formatting didn't fix the issue. Still fails regardless of drivers installed. Hardware was purchased ~6months ago. Running a good SSD. Event viewer Always these two messages in close succession: Error (event ID 6008): The previous system shutdown at 7:45:21 PM on ?27/?10/?2012 was unexpected. Critical (kernel power, event ID 41): The system has rebooted without cleanly shutting down first. This error could be caused if the system stopped responding, crashed, or lost power unexpectedly. Upon installing WPT as suggested below to figure out what was happening during shutdown, and running the cmd xbootmgr -trace shutdown -noPrepReboot -traceFlags BASE+CSWITCH+DRIVERS+POWER -resultPath C:\TEMP Windows fast start-up is now working consistently. Still works upon uninstalling WPT. This is the only change to occur on the computer. Nothing else has bee installed/uninstalled, no Windows Updates, nothing. Windows fast start-up did not work prior to installing WPT and running the cmd (made sure I tested).

    Read the article

  • Xorg input devices fail without udev

    - by Sampo
    What I am trying to do: Launch Xorg server without udev device manager. What I have tried to do: Make sure that /dev/ has all required nodes, such as /dev/input/*. Make sure that all required kernel modules are loaded. Launch Xorg. What happens: Xorg starts up as excepted. Xorg loads correct GPU driver and sets right screen resolution. Xorg blocks all input devices (keyboard, mouse), Alt+F[1-12] does not work (can't go back to tty1). Unraw'ing keyboard to take its control from X removes blocking and after unraw I can Alt+F1 back to tty1. Xorg still does not handle any input. Why I think that it should work: Same configuration works well if udev is loaded. Loading udev does not add or modify /dev/ contents, all nodes stays same. My main question is: How to make Xorg input devices work without udev? Any additional information about how Xorg really uses/detects/grabs keyboard would be helpful. And any additional information about what udev really does (other than populating /dev/) would also be helpful.

    Read the article

  • Apple / Mac OS X - Is there a Package Manager like Linux

    - by Walter White
    I am a Linux/UNIX user and love the package management that comes with it. For the most part, I like Ubuntu, but just like anything else, it is the minor things that you live with daily that would be nice if they just worked. My main issue is my wacom tablet while it works, every time there is an OS update, I have to rebuild the wacom driver. The other slightly annoying issue is, my ATI video card is not fully supported. When I use the HDMI out, the sound doesn't go through it, and the screen is not entirely used. I would happily get an Apple if it had a similar package management system like Ubuntu, Gentoo, or other Linux distribution. This takes the work out of getting the latest enhancements or fixes. It also takes all the guess work out about what you need to get something to work. I just want to use my computer, not administer it. Aside from Apple applications, if I wanted to install the GIMP on an apple, would it go and fetch ufraw if I wanted support for that and whatever other dependencies GIMP has? If I want Netbeans installed, will it go and get a JDK and maven if I want that? If not, is there something in the works? I know I don't update my applications that frequently, but that is mainly because I'm not aware of the updates. The updates all happen in the background. Walter

    Read the article

  • Dell XPS 15 L502X hard drive Partition

    - by Mohan Gajula
    I have a situation here. I got my new Dell XPS 15 Laptop. The configuration of hard drive is as below : Volume 1: (OEM Partition): 133MB Volume 2: OS (C:): 685.25 GB Volume 3: Recovery : 13.25 GB Now, I am trying to re-partition my C Drive to have a C: drive with 100 GB and a new drive with 585 GB. Earlier, I tried using the Windows 7 Disk Management to shrink and extend the volume. That lead to the OS and hard drive not working. Dell Tech support tried to fix the issue, but they were not able to fix the issue online. Later a Dell Technician arrived my place, and replaced the hard drive with a new hard drive. Please help me re-partition the C: Drive with 100 GB, and new D drive with 585 GB. I don't want to lose my Recovery Partition. SOLUTION As Suggested by KCotreau below , I have done exactly. I have resized the C drive to 100 GB. And then applied the changes. Windows got restarted. On the boot screen, the partition was taking place. It took around 30 mins ( approx. ). Once after restart, I can see my C drive is 100 GB. Now opened the Easeus again. And created a new partition for the free space ( 585 GB ) this took 10 seconds to create. Here goes the screenshot after partitioning. Thanks to KCotreau. You are amazing.

    Read the article

  • How to fix a bootable USB Kubuntu installation when the drive has maxed out?

    - by NoCatharsis
    I used Universal-USB-Installer-v1.5.1 from PenDriveLinux.com with Kubuntu 10.04 so I could set up my 4GB flash drive as a totally independent installation. Unfortunately, there was an OS upgrade available which Kubuntu downloaded and attempted to install. This, along with some other software, apparently maxed out my drive before I realized it. Now when I try to boot from the drive, everything boots as normal to the OS boot screen where I select "Boot from this Kubuntu USB Installation." The startup process initiates, then stalls about halfway through and hangs indefinitely. I'm guessing the drive is trying to use space it doesn't have and completely stops working. I realize that once the OS upgrade is in place, the old files could be deleted for a potential 700MB space gain. However, I just have no way to get into the OS and complete the upgrade. My main OS is Windows 7. Is there a way I can fix this issue from within Windows without formatting the entire drive and reinstalling Kubuntu from scratch?

    Read the article

  • During Vista Repair - No operating system is listed.

    - by Jack Marchetti
    After a Windows update, my brother's Gateway computer loads to the "Step 3 of 3: 0%" and reboots. Safe Mode does not work. I placed a Vista DVD in the drive, and re-booted. (Note, this is my Vista DVD, not the Recovery/System disc that would come with a computer. Gateway does not give you CD's anymore. I believe they store recovery on a partition, but that partition has been wiped out). I chose "Repair Your Computer" I get a dialog box, but no operating system is listed. I'm then prompted to "Load Drivers". What drivers am I supposed to be loading here and where from? I placed a CD in the drive to "load drivers" but I don't see my DVD drive listed. All I saw where X:/Sources along with several Removable Media slots that were empty. On another screen I tried Startup Repair, which didn't do anything. I attempted to use System Restore - but it doesn't detect the hard drive. I'm guessing that I'm missing some sort of SATA driver and that is why the hard disk is not being found. Any ideas on this?

    Read the article

< Previous Page | 579 580 581 582 583 584 585 586 587 588 589 590  | Next Page >