Search Results

Search found 19018 results on 761 pages for 'indicator network'.

Page 584/761 | < Previous Page | 580 581 582 583 584 585 586 587 588 589 590 591  | Next Page >

• iPad revocable vpn access

  - by carpat

  I'm a programmer at my organization, but somehow got drafted into looking into some server stuff so forgive me of my ignorance: They want to give our sales people secure access to our internal sites using their iPads. This must be secure (obviously) but also revocable from the company's side (if someone quits they can no longer access our network). I see from http://support.apple.com/kb/HT1288 that the iPad supports "RSA SecurID", "CRYPTOCard", and "Kerberos" authentication methods. Will one of these do what we need? Are there any major differences between them?

  Read the article

• Ubuntu: nautilus cannot browse samba shares

  - by Alexey Pilipchuk

  Got a problem with browsing samba shares with nautilus in ubuntu i can see workgroups but cannot go any deeper. On the other hand i can use smbclient and mount samba shares from command line. Also i can browse ubuntu shares from windows but not vise versa. So i suspect it is nautilus problem. Moreover it has never been working for me since very first ubuntu i used. Systems i tryed to browse shares on: Ubuntu 8-12 Windows Xp 7 Dune HD Max Could someone provide me with ideas how to diagnose this issue? Or describe how network browsing is implemented in nautilus Thanx in advance

  Read the article

• Just installed 13.10 and everything is fine except I cannot connect to the internet. Any thoughts?

  - by razorccatu

  I just installed Ubuntu 13.10 on my HP G62 laptop and the install went smoothly. I did the install off of a USB drive after trying ubuntu. While I was testing it, I connected to my Wireless with out issue and surfed a little. After the install, no wireless. I can still connect to my wireless network (at least it tells me I'm connected at full strength) but No servers can be found. I attempted to ping Google to no avail and I attempted to ping my router to no avail. I tried to then hard wire the machine and once again it told me that I was connected but I was not. When I ran dmesg, I got the following message: Warning: nss-myhostname is not installed. Changing the local hostname might make it unresolvabe. Please install nss-hostname! Is the hostname the issue? if so, how do I resolve it with out internet connection? If it's not the issue, how do I move forward? Thanks for any help. EDIT. I forgot to attach the image of my ifconfig if that might help.

  Read the article

• linux intrusion detection software

  - by Sam Hammamy

  I have an Ubuntu VPS that I use for practice and deploying prototypes as I am a python developer. I recently started teaching my self sys admin tasks, like installing OpenLDAP. I happened to turn off the ufw firewall for just a minute, and when I ran an netstat command, I saw a foreign ip connected to ssh that I traced to china. I'd like to know a few things: 1) Is there any good network intrusion detection software, such that if any IP that's outside a specific range connects to the VPN, I can be notified? -- I am thinking about scripting this, but I'm pretty sure there's something useful out there and I believe in the wisdom of crowds. 2) How did this person gain access to my server? Is it because my firewall was down? Or is it because they browsed my LDAP directory and from there figured out a way to connect (there was a clear text password in the tree but it wasn't one used by the server's sshd)?

  Read the article

• Samba / smbd on Centos 6.5

  - by Satalink

  I've installed Samba4 and have the smb.conf file as follows: [global] workgroup = WORKGROUP server string = Samba Server realm = REXIALO.COM netbios name = REXIALO.COM security = user map to guest = Bad Password bind interfaces only = no interfaces = lo venet0 log file = /var/log/samba/samba.log max log size = 1000 [webroot] path = /usr/local/apache/htdocs comment = Example.com webroot directory read only = No I can connect from the same server with smbclient. Localhost: # smbclient -L localhost -U root Domain=[WORKGROUP] OS=[Unix] Server=[Samba 4.1.11] Sharename Type Comment --------- ---- ------- webroot Disk RexiAlo webroot directory IPC$ IPC IPC Service (RexiAlo Samba Server) Domain=[WORKGROUP] OS=[Unix] Server=[Samba 4.1.11] Server Comment --------- ------- Workgroup Master --------- -------Enter root's password: network: # smbclient -L rexialo.com -U Domain=[WORKGROUP] OS=[Unix] Server=[Samba 4.1.11] Sharename Type Comment --------- ---- ------- webroot Disk RexiAlo webroot directory IPC$ IPC IPC Service (RexiAlo Samba Server) Domain=[WORKGROUP] OS=[Unix] Server=[Samba 4.1.11] Server Comment --------- ------- Workgroup Master --------- ------- The problem is when I try to map to the smb webroot from Windows 7, it asks for user/pass but just times out and then prompts for credentials. The samba.log file does not show any activity other than the startup of the smbd process. Any help would be appreciated.

  Read the article

• How can I measure TCP timeout limit on NAT firewall for setting keepalive interval?

  - by jmanning2k

  A new (NAT) firewall appliance was recently installed at $WORK. Since then, I'm getting many network timeouts and interruptions, especially for operations which would require the server to think for a bit without a response (svn update, rsync, etc.). Inbound SSH sessions over VPN also timeout frequently. That clearly suggests I need to adjust the TCP (and ssh) keepalive time on the servers in question in order to reduce these errors. But what is the appropriate value I should use? Assuming I have machines on both sides of the firewall between which I can make a connection, is there a way to measure what the time limit on TCP connections might be for this firewall? In theory, I would send a packet with gradually increasing intervals until the connection is lost. Any tools that might help (free or open source would be best, but I'm open to other suggestions)? The appliance is not under my control, so I can't just get the value, though I am attempting to ask what it currently is and if I can get it increased.

  Read the article

• Annoying Search Behavior - Search Companion

  - by DavidStein

  I'm running Windows XP Professional, and ever since the last service pack I've had a searching problem. When I want to search a network drive, I get the following message: This folder is not indexed. To search this directory plase use Search Companion or add this directory to your index via options. Basically, I have two questions. Is there some way that I can use the indexed search where appropriate and then have it switch over to the Search Companion automatically? Second, how does a programmer look at this code and think this is a good idea? I realize that this question is rhetorical. However, I must enter my search string into one search, receive the error, and then click "Search Companion" to bring up the new search window. This window doesn't even take the defaults from the previous one so I have to specify the search string and drive again.

  Read the article

• How to register a new domain name on a windows based domain controller?

  - by JL

  Is there an easy and quick way I can create a new subdomain on a windows based domain controller. My primary domain controller is also my primary DNS server on my network. I want to create a subdomain and have its ip directed to that of my IIS server. Thanks in advance... Sorry if my terminology is somewhat lacking... My domain is companyName.com What I want to do is create auditingResults.companyName.com... and have it route to 192.168.1.3 for example..... where on 1.3 I will have an IIS server presetup. Please feel free to leave comments to correct my terminology if required....

  Read the article

• WinXP workgroup, 3 routers 3 computers

  - by Silvera

  I have 3 computers with WinXP x86, and 3 Cisco 1800 series routers. I'm trying to create a workgroup so that the 3 computers can share files with eachother. They can ping eachother (without any internet connection), and the routers setup is correctly configured (with interfaces, ip adresses, and ports). But none of the computers can see eachother, even though they are on the same network. My first question would be - can it be done the way it is currently configured - and, if yes, how, or can anyone point me in the right direction?

  Read the article

• How to find out when to increase bit rate? (TCP streaming solution)

  - by Kabumbus

  How to find out when to increase bit rate? (TCP streaming solution) We have a stream with "frames". each "frame" has a "timestamp" . frames have bit rate property which is actually there size. We generate frames with our app and stream them one by one on to our TCP server socket. At the same time server post replies so when after each sent frame we try to read from socket we receive which timestamp is currently on server. if timestamp is lover than previous frame we lover bit rate 20%. Such scheme seems to work giving me one way vbr (lowering) but I wonder how to implement increase? I mean we can always try to increase 5% each frame until some limited desired value but each time we have delay will lose real-time feature of our stream... Generally such scheme is for finding out how much of network stream is currently used by other user apps and give picture of how much server is loaded at the same time so we can stream just right amount of data for all to receive it in real time. So what shall I do to add increase to my scheme? So having current bit rate of A I thought we could add +7% for 3 frames and than one -20% and than if all that 3 frames with +7% came in time we could add 14% to A and repeat circle and it would hopefully not be really noticeable if 2nd frame wold come to us with delay... probably this one is too localised because it is a requirement for me to use TCP.

  Read the article

• How secure is cloud computing?

  - by Rhubarb

  By secure, I don't mean the machines itself and access to it from the network. I mean, and I suppose this could be applied to any kind of hosting service, when you put all your intellectual property onto a hosted provider, what happens to the hard disks as they cycle through them? Say I've invested million into my software, and the information and data that I have is valuable, how can I be sure it isn't read off old disks as they're recycled? Is there some kind of standard to look for that ensures a provider is going to use the strictest form of intellectual property protection? Is SAS70 applicable here?

  Read the article

• Need advice on how to set up live video streaming to web/mobile devices

  - by jasondewitt

  I have a bunch of live udp video streams that currently are viewed by set top boxes in my network. I would like to pick this video up (I can do this with vlc now) and stream it out to other non-STB endpoints (webpage or a phone/tablet of some sort). Right now I am able to pick up the udp stream with vlc and convert it to an http stream on port 8080 of my vlc box. Then I can use the vlc client to pick up and watch that video stream. This is where I'm not sure where to go with it. I really doubt I would want everyone who is watching the video to make a connection back to my vlc server that is doing the encoding, so how do I distribute this live video to the people who want to see it?

  Read the article

• Router used as ethernet bridge wont show up

  - by user1255271

  I have a Netgear router in my living room that has the wireless signal. It is connected to a Powerline plug that goes up to my bedroom. That is plugged into another router that is used as an ethernet hub. It's cables go into my PS3 and my server. The second router shows up as a hidden network on my laptop, and I can connect to it. But it is not listed as an attached device on my main router, and my laptop says that it connects straight to the main router, not the second one. How can I connect to this router? Aside from swapping the two? Thanks in advance.

  Read the article

• NAT : understanding about interconnection

  - by PITCHY

  English version below J'ai 2 routeurs A et B relié en série avec les ip respectives ( 10.0.0.1/30 10.0.0.2/30) sur le routeur A j'ai activé la fonction NAT avec un pool (200.0.0.1 - 200.0.0.15/28). Lorsque je sors je prends donc un ip du pool par exemple 200.0.0.10. Comment ça fonctionne sachant que ma nouvelle ip (200.0.0.10) ne se trouve pas sur le meme réseau que mon interface de destination (10.0.0.2)? English: I have 2 routers A and B, interconnected with a serial connection, with the ip's 10.0.0.1/30 for A and 10.0.0.2/30 for B. On router A NAT was activated with the pool 200.0.0.1 - 200.0.0.15/28. When connection to this router, I get an ip from the pool, for example 200.0.0.10. Knowing my new ip is 200.0.0.10, which is not on the same network as my destination interface (10.0.0.2), how can this work?

  Read the article

• Access device with local ip over internet

  - by Joe Perrin

  I apologize up front if this is the wrong place to post this question. It seemed like the best fit. I have a device which is connected to my local network which has an IP of 192.168.1.10 from my router. Additionally I use a Windows 7 machine that runs some software called DirectUpdate which allows me to resolve the local IP of the Windows 7 machine (192.168.1.5) to be accessible to the internet via my domain (example.com) - Basic dynamic DNS updating. I'd like to access the device from example.com. I am unsure how to do this as I don't have any way to install DirectUpdate (or any software) on the device to make the device available to the internet. Any insight here would be appreciated. Thank you.

  Read the article

• Enterprise Portal Issue with the Ax Demo VPCs

  - by ssmantha

  Microsoft’s Ax Demo VPC is basically configured for a static IP address 192.168.0.1, this is due to the fact that the VPC has Domain Controlller configured in it which requires a static IP. When we put this VPC on a network with a different subnet and change the IP you can observer that the site http://sharepoint and http://sharepoint/EP cease to function and show “Page Not Found” errors in the browser. This is mainly due to the DNS configuration which is not updated. Below is the screen shot of the changes that needs to be done to make the site functioning properly. Change the following entries in the Forward Lookup Zones of DNS management: These websites default, SharePoint and projectserver are all mapped to a single port in the IIS i.e. port number 80. These websites are recognised with host headers. These host headers are configured in DNS with incorrect IP address entries in DNS when you change the IP address of the VPC. Just change these values to point to the Local Loop Adapter (127.0.0.1) and change the DNS to point to this address in the TCP/IP properties as shown below: This will resolve the issue with the website rendering. Initially you may get time out errors while browsing these website. be patient and try again this would work.

  Read the article

• How do I connect a laptop running Windows 7 to an Android phone using WiFi Direct?

  - by user130768

  From where I am sitting, Windows 7 does not appear to support WiFi Direct connections to Android mobile devices. Specifically, turning on WiFi Direct on my Samsung Galaxy S II does not make the device visible as a potential WiFi network connection. Windows 8 is said to support WiFi Direct, but I have no desire to upgrade at this time. I have successfully set up ad hoc WiFi connections between the S II and my laptop before, but as you may be aware, these are not the same as WiFi Direct. Before posting this question, I searched [ "Windows 7" "WiFi Direct" ] and variations thereof, and dutifully slogged through dozens of lame or irrelevant responses on various forums, badly made YouTube videos, and probable Trojan horse distribution sites. If someone out there knows how to do this, it's buried in the noise.

  Read the article

• Logs being flooded from Squid for having intercepted and authentication enabled together

  - by Horace

  I have done some hefty Google'ing and I can't seem to find a single solution to this issue that I cam currently experiencing. Here is a sample configuration from squid that I have: # # DIGEST Auth # auth_param digest program /usr/sbin/digest_file_auth /etc/squid/digpass auth_param digest children 8 auth_param digest realm LHPROJECTS.LAN Network Proxy auth_param digest nonce_garbage_interval 10 minutes auth_param digest nonce_max_duration 45 minutes auth_param digest nonce_max_count 100 auth_param digest nonce_strictness on # Squid normally listens to port 3128 # Squid normally listens to port 3128 http_port 192.168.10.2:3128 transparent https_port 192.168.10.2:3128 intercept http_port 192.168.10.2:3130 As noted above, I have three ports defined, 2 of them are transparent/intercept and one is a regular http port (which I use for authentication). Which works rather well in this configuration however my logs are getting flooded of this entry authentication not applicable on intercepted requests whenever a transparent connection is made. So far, I can't seem to find any documentation that would describe how to suppress these messages ?

  Read the article

• Working with Git on multiple machines

  - by Tesserex

  This may sound a bit strange, but I'm wondering about a good way to work in Git from multiple machines networked together in some way. It looks to me like I have two options, and I can see benefits on both sides: Use git itself for sharing, each machine has its own repo and you have to fetch between them. You can work on either machine even if the other is offline. This by itself is pretty big I think. Use one repo that is shared over the network between machines. No need to do git pulls every time you switch machines, since your code is always up to date. Never worry that you forgot to push code from your other non-hosting machine, which is now out of reach, since you were working off a fileshare on this machine. My intuition says that everyone generally goes with the first option. But the downside I see is that you might not always be able to access code from your other machines, and I certainly don't want to push all my WIP branches to github at the end of every day. I also don't want to have to leave my computers on all the time so I can fetch from them directly. Lastly a minor point is that all the git commands to keep multiple branches up to date can get tedious. Is there a third handle on this situation? Maybe some third party tools are available that help make this process easier? If you deal with this situation regularly, what do you suggest?

  Read the article

• ts_block.vbs and mac intosh

  - by Eric Le breton

  I am using your excellent ts_blocker, release 20120530, on my server 2008 R2 Enterprise. it works very fine, i use the vbs script, launched with wscript. The only problem is that is does not work for users attempting to connect RDP from a mac intosh. With this machine the distant IP seems to be not recognized when the login fails. The IP is visible when the login is good (event ID 4624) but not when it fails (Audit failure event ID 4625) : then the IP is not to be seen in the event log ! In the "network information" of the event log entry is nothing given. Have you already been told of that and is there something to do ?

  Read the article

• How to specify multiple HostName/Port combinations in .ssh/config

  - by leoluk

  I have multiple notebooks and workstations which pull and push from multiple Mercurial repositories on a central server. I usually use .ssh/config to set an alias: Host repo-server HostName server.somedomain User user143 IdentityOnly yes IdentityFile ~/hgkey Port 156 ... and some more options, you get the idea. I can then simply do a hg push ssh://repo-server//hgroot/someproject on every local repository, and I can change the server address and port in one place. For workstations, this works fine, but the notebooks can access the server either from inside the network or from outside, using a different address and a different port. Is there any way I can specify multiple HostName/Port combinations so that SSH automatically tries them in order? This way, the users could push and pull without having to care about the correct address. (of course, using a VPN would be the most correct solution)

  Read the article

• what to do when ctrl-c can't kill a process?

  - by Dustin Boswell

  Ctrl-c doesn't always work to kill the current process (for instance, if that process is busy in certain network operations). In that case, you just see "^C" by your cursor, and can't do much else. What's the easiest way to force that process to die now without losing my terminal? Summary of answers below: Usually, you can Ctrl-z to put the process to sleep, and then do "kill -9 process-pid", where you find the process's pid with 'ps' and other tools. On Bash (and possibly other shells) you can do "kill -9 %1" (or '%N' in general) which is easier. If Ctrl-z doesn't work, you'll have to open another terminal and kill from there.

  Read the article

• Which is the best internet security + Antivirus solution for Windows?

  - by metal gear solid

  Which is the best internet security + Antivirus solution for Windows? free/opensource or commercial it doesn't matter I need best solution. Is Kaspersky best ? or any other? http://www.kaspersky.com/kaspersky_internet_security Award-winning technologies in Kaspersky Internet Security 2010 protect you from cybercrime and a wide range of IT threats: * Viruses, Trojans, worms and other malware, spyware and adware * Rootkits, bootkits and other complex threats * Identity theft by keyloggers, screen capture malware or phishing scams * Botnets and various illegal methods of taking control of your PC or Netbook * Zero-day attacks, new fast emerging and unknown threats * Drive-by download infections, network attacks and intrusions * Unwanted, offensive web content and spam

  Read the article

• What is involved with writing a lobby server?

  - by Kira

  So I'm writing a Chess matchmaking system based on a Lobby view with gaming rooms, general chat etc. So far I have a working prototype but I have big doubts regarding some things I did with the server. Writing a gaming lobby server is a new programming experience to me and so I don't have a clear nor precise programming model for it. I also couldn't find a paper that describes how it should work. I ordered "Java Network Programming 3rd edition" from Amazon and still waiting for shipment, hopefully I'll find some useful examples/information in this book. Meanwhile, I'd like to gather your opinions and see how you would handle some things so I can learn how to write a server correctly. Here are a few questions off the top of my head: (may be more will come) First, let's define what a server does. It's primary functionality is to hold TCP connections with clients, listen to the events they generate and dispatch them to the other players. But is there more to it than that? Should I use one thread per client? If so, 300 clients = 300 threads. Isn't that too much? What hardware is needed to support that? And how much bandwidth does a lobby consume then approx? What kind of data structure should be used to hold the clients' sockets? How do you protect it from concurrent modification (eg. a player enters or exists the lobby) when iterating through it to dispatch an event without hurting throughput? Is ConcurrentHashMap the correct answer here, or are there some techniques I should know? When a user enters the lobby, what mechanism would you use to transfer the state of the lobby to him? And while this is happening, where do the other events bubble up? Screenshot : http://imageshack.us/photo/my-images/695/sansrewyh.png/

  Read the article

• Diving into a computer science career [closed]

  - by Willis

  Well first I would like to say thank you for taking the time to read my question. I'll give you some background. I graduated two years ago from a local UC in my state with a degree in cognitive psychology and worked in a neuroscience lab. During this time I was exposed to some light Matlab programming and other programming tidbits, but before this I had some basic understanding of programming. My father worked IT for a company when I was younger so I picked up his books and took learned things along the way growing up. Naturally I'm an inquisitive person, constantly learning, love challenges, and have had exposure to some languages. Yet at this point I was fully pursue it as a career and always had this in the back of my head. Where do I start? I'm 25 and feel like I still have time to make a switch. I've immersed myself in the terminal/command prompt to start, but which language do I focus on? I've read the A+ book and planning to take on the exam, then the networking exam, but I want to deal with more programming, development, and troubleshooting. I understand to get involved in open source, but where? I took the next step and got a small IT assistant job, but doesn't really deal with programming, development, just troubling shooting and small network issues. Thank you!

  Read the article

< Previous Page | 580 581 582 583 584 585 586 587 588 589 590 591  | Next Page >