Search Results

Search found 111248 results on 4450 pages for 'end user computing'.

Page 589/4450 | < Previous Page | 585 586 587 588 589 590 591 592 593 594 595 596  | Next Page >

• Can one really fry a monitor by setting the wrong HorizSync and VertRefresh?

  - by rumtscho

  I've encountered this problem on several different systems with several different monitors: a monitor functions perfectly under Windows. I install a Linux and the max resolution is at some impossibly low value, mostly 640x480, changing it in Xorg.conf doesn't work. The X.org log file then shows that the driver cannot determine the correct refresh rate for the monitor, so it ignores everything in Xorg.conf and just loads in some default minimalistic mode. Googling the problem leads to an easy solution: set the HorizSync and VertRefresh in Xorg.conf, and everything works. The problem seems to be a common one, and I've seen dozens of results recommending the solution. Each of them contains the warning that you should use the value ranges provided with the monitor. Because if you don't, and your video card sends a signal with the wrong refresh rate, this can damage your monitor. Of course, you don't have a user manual for your monitor any more. If you are lucky to find one on the attic or on the net, it doesn't contain any information about the supported refresh rate. So you just type in the value suggested in the solution description, which varies wildly depending on your source, and cross your fingers. You restart, and... ... you've set the wrong values. So the monitor shows a short message like "input signal out of range", and you do a hard restart, repair your Xorg.conf in recovery mode, and everything is fine, including your monitor. So does this warning reflect a real possibility, or is it just a geeky urban legend? Or is it something which used to happen in the past, before manufacturers started protecting the monitors against it? Is it technically possible with every monitor technology, or is it maybe something which can only happen to a CRT? If you think that it's true, why? Have you ever witnessed a monitor die from the wrong refresh config, or have you read of it in a reputable source?

  Read the article

• Leopard mail.app quoted-printable weirdness

  - by pehrs

  I am not sure if this is a bug in mail.app, or a configuration I just can't find. It might also be a strange sideffect of GPGmail. Mail.app correctly displays all e-mails on my IMAP server, except for the e-mails in my "Sent Messages" folder. In the sent messages folder it messes up åäö, in typical quoted-printable with wrong char-set fashion. They become ‰ˆ. When looking at the source of the e-mails it seems like the header generated by mail.app is correct: Message-Id: <> From: To: In-Reply-To: <> Content-Type: multipart/signed; protocol="application/pgp-signature"; micalg=pgp-sha1; boundary="Apple-Mail-4--741321197" X-Smtp-Server: smtp.example.com Content-Transfer-Encoding: 7bit Mime-Version: 1.0 (Apple Message framework v936) Subject: Example subject Date: Fri, 26 Mar 2010 10:14:14 +0100 References: <> X-Pgp-Agent: GPGMail 1.2.0 (v56) This is an OpenPGP/MIME signed message (RFC 2440 and 3156) --Apple-Mail-4--741321197 Content-Type: text/plain; charset=ISO-8859-1; format=flowed; delsp=yes Content-Transfer-Encoding: quoted-printable <Text here with =E5=E4=F6> --Apple-Mail-4--741321197 content-type: application/pgp-signature; x-mac-type=70674453; name=PGP.sig content-description: This is a digitally signed message part content-disposition: inline; filename=PGP.sig content-transfer-encoding: 7bit -----BEGIN PGP SIGNATURE----- Version: GnuPG/MacGPG2 v2.0.12 (Darwin) iEYEARECAAYFAkus62kACgkQlIRLofxhDjYnnwCcDmCXuMGsKlh3a418s12coJgn 36sAoKMdkP3+g/OMK+Ps7AbjQq4Nbqzv =XMko -----END PGP SIGNATURE----- --Apple-Mail-4--741321197-- Thunderbird has no problem displaying the messages. So, how can I get mail.app to use the correct charset?

  Read the article

• Hard drive had reallocated sectors...but now it magically doesn't! Can I trust it?

  - by rob

  Last week my SMART diagnostics utility, CrystalDiskInfo, reported that the external hard drive that I was saving my backups to had suddenly reported 900+ reallocated sectors. I double-checked to confirm, then ordered a replacement drive. I spent all of this week copying data from that drive to the new drive. But toward the end of the copy, something peculiar happened. CrystalDiskInfo popped up an alert that the reallocated sector count had gone back down to 0. I know that when SMART detects a read error on a block, it adds that block to the current pending reallocation list. If it subsequently is successfully written or read later, it is removed from the list and assumed to be fine, but if a subsequent write fails, it is marked bad and added to the reallocated sector count. What concerns me most is that I've never read anywhere that a sector can be recovered as "good" after it has been marked as a bad sector and remapped. I've just finished running an extended SMART diagnostic, and it found no surface errors. Now I'm doubtful that the manufacturer will honor a warranty claim if the SMART info does not report any problems. Has anyone had this happen? If so, then is the drive, indeed, okay, or should I be concerned about an imminent failure?

  Read the article

• Which internet scenario would be better?

  - by JL

  I currently have an 8mbps (down) / 512kbps (up) telephone ADSL solution. I must say the reliability is excellent, and up until now its been the fastest connection I could get because I don't live in a cable zone. The real speed of my connection is around 7mbps, but sometimes I manage to get the full 8mbps. I use my connection for work, so it needs to be at least 99% reliable. Recently I was told by a guy who lives up the road that he has a wireless connection with an external antenna and his speeds are 20mbps / 512kbps - he's also paying about 1/2 of what I pay for my wired telephone connection. My question is, is wireless internet good enough for a power user who uses his connection for work 8 hours a day, including VPNing into servers remotely. Besides this I also enjoy playing the odd network game, not a WoW freak, but sometimes I do pick up the odd MMORPG and at times do indulge in some semi heavy gaming sprees. Will this wireless latency drive me crazy and seem slow in comparison? Will it be reliable enough, I also live in an area that snows heavily in winter. I guess its a question of - should I go wireless or not. I've only had 1 wireless connection before and that was years ago using iBurst technology and I remember it was terrible for VPN, but I guess the technology might have been improved since then? What do you guys think?

  Read the article

• Windows 7 home backup solution, with offsite provision

  - by Richard E

  I am looking for a home backup solution for my single Windows 7 (Home Premium) PC. I have about 500GB of data to backup. I would like to spend less than GBP 300 on the solution. I don't see the need to backup the whole PC, rather specific folder branches (iTunes, photos, documents, Outlook files, user folders such as desktop, favorites etc). I would like a solution that enables me to maintain backups in two separate physical locations (e.g. home and work). To facilitate this I am imagining a storage unit with slots for two removable drives, along with three separate drives. At any one time two of the drives will be being backed up to in the storage unit. The third will be located at my work. Periodically I will take one of the drives into work and leave it there, then bring the drive that was there back home, and plug it into the storage unit. It will then be backed up along with the other drive that was left in the storage unit. This approach should cover scenarios such as virus attack and fire or theft from one location. Thoughts and comments on the sanity of this approach please...

  Read the article

• passing on command line options in bash

  - by bryan

  I have a question. I have a script, a kind of long script written in bash aprox. 370 lines. That has several functions and in those functions the user has to enter information which is then stored in files. ( This is suppose to represent a MySQL database, with the functions INSERT, UPDATE, SELECT, SELECT where x=y.) I created this myself in bash, now the only thing that rests me is that I need to be able to pass arguments on the command line to the script, that will do the same as the script does. I know that bash has positional parameters such as $1 $2 $3 $* $@ $0 ( refers to the name of the script) etc. I know how I can use these parameters in a simple if function. This is not enough for my script. I basicly need to do the same thing that the script does, but then from the command line. I have been struggling with this for a couple of days now and I cannot think of a way to get it to work. Maybe someone here can help me with this? If you want to have the script. That can be possible, but I don't think I can paste it in here... EDIT: Link to script, http://pastebin.com/Hd5VsDv2 Note, I am a beginner in bash scripting. EDIT: This is in reply to Answer 1. As I said I hope I can just replace the if [ "$1" = "one" ] ; then echo "found one" to if [ "$1" = "one" ] ; then echo SELECT where SELECT is the function I previously had in my script(above) http://pastebin.com/VFMkBL6g LINK to testing script

  Read the article

• Font for Wine that supports the entire character set of the Win32 Console?

  - by Brian Campbell

  I would like to be able to display in the Wine console all characters that the Win32 console can display. I've written a small test program to print out all 8-bit characters: #include <stdio.h> int main(int argc, char *argv[]) { int i, j; for (i = 0; i <= 0xF0; i+=0x10) { for (j = i; j <= i + 0x0F; ++j) printf("%2x:%c", j, (char)j); printf("\n"); } getchar(); return 0; } Under Wine, the best I can do so far is using Andale Mono: While this is what I see on Windows Server 2008: Is there anywhere I can legally download a font that will allow me to view all of those characters under Wine? edit I've found a set of DOS fonts that includes a CP437 font, which should cover the character set I'm interested in. However, even if I install this font, wineconsole doesn't seem to recognize it. Is there any way I can get wineconsole to use this font, or convert this font to a format that wineconsole can use? Or is there any way I can extract fonts from DOSEMU for use in Wine? Oh, and I should probably mention that I'm on Mac OS X 10.6.2, installing Wine via MacPorts, using the wine-devel package. more information I have tried installing some console fonts that should cover the full character set as Mac OS X fonts (such as the NewDOS font listed above, and a font I tried converting from the fonts supplied by DOSEMU). Wine does not seem to pick up on new fonts installed in Mac OS X. Is there a way to register new fonts I've installed with Wine? Would manually editing the system.reg file that seems to contain font mappings work, or is there something else I'd need to do? bump Bounty ends soon, I'm still looking for an answer for this. Does anyone use the Wine console for complex text user interfaces?

  Read the article

• Devices on one switch can't see devices on another switch

  - by jockey69

  I have RoadRunner Internet cable service hooked to a Motorola Surfboard modem. This is connected to a 10/100 wireless router (located in the garage). Downstairs, I have a ZyXEL GS-108b gigabit switch connected to one port on the router. From this switch I ran connections to a PS3, DVR, Vonage box and a wireless router (Buffalo AirStation 10/100). The Buffalo AirStation works as a wireless AP for other laptops, iPads and cell phones. Upstairs, I have an Asus gigabit switch connected to a gaming desktop, printer, and a media server on FreeNAS (PS3 Media Server on FreeNAS). The router is configured to assign static IPs to both the PS3 and the media server. Problem - I connect a laptop to the switch downstairs after disabling the wireless, thus making sure that I am accessing internet through the wired connection (and the router in the garage). All my computers, iPads and cell phones are able to connect to the internet without a problem. My PS3 connects to the interent with a wired connection but is unable to access the media server (I get a message that no media server is found). I used a wired laptop downstairs (connected to switch downstairs) but am unable to ping either the PS3 or media server! I may be doing something silly but am at my wits' end. Please help!

  Read the article

• Single application through OpenVPN tunnel (Debian Lenny)

  - by mikael

  I'm using Debian Lenny and I want to tunnel rtorrent only through a OpenVPN tunnel. I have a tunnel running, the config file looks like this: client dev tun proto udp remote openvpn.xxx.com 1194 resolv-retry infinite nobind persist-key persist-tun ca /etc/openvpn/xxx/keys/ca.crt cert /etc/openvpn/xxx/keys/client.crt key /etc/openvpn/xxx/keys/client.key tls-auth /etc/openvpn/xxx/keys/tls.key 1 ns-cert-type server comp-lzo verb 3 auth-user-pass script-security 3 reneg-sec 0 My idea is that I could run a sockd proxy internally that redirects traffic to the openvpn tunnel. I could use the *nix "proxifier" application "tsocks" to make it possible for rtorrent to connect through that proxy (as rtorrent doesn't support proxies). I have trouble configuring sockd as my IP inside the VPN changes every time I connect. This is a config file someone said would help: http://ircpimps.org/sockd.conf As my IP changes at each connect I don't know what to put in that config file. I have no control over the host side config file. Any help wanted. Any other method is very welcome.

  Read the article

• How to repair Mac OS X without reinstalling?

  - by RahulVyas

  I have an Intel PC. I have installed iDeneb Mac OS X in my PC. It's running fine. After that I thought about installing Snow Leopard for running the iPad SDK. So I bought a retail Snow Leopard and booted it with Rebel EFI boot loader. When I was installing Snow Leopard, at the end of installation, setup gives an error. So I restarted my PC and boot with Rebel and I saw that the Mac was there so I booted that into safe mode and Mac OS X runs. After that I installed iPad SDK. But when I try to create an application, Xcode is not responsive. It hangs when I choose new project, give it a name and save it on disk. After just as I gave name and choose save it hangs. Is there any way I can repair my Mac OS X without reinstalling? I have also been unable to boot into normal mode and also without Rebel CD. So I want to boot without Rebel CD and also want to run iPad SDK.

  Read the article

• Firefox 29 - how do I delete history entries visited fewer than x times

  - by lousyuser

  Context: I've been using my Firefox profile for a couple of years now. My history file has become huge, naturally. I got Firefox Sync set up between my main desktop PC and my laptop. HW configs: PC: i5-3450, 8 GB DDR3 RAM, Crucial M4 128 GB SSD laptop: Pentium SU4100, 4 GB DDR3 RAM, WD 5400 rpm HDD Accessing history entries when typing into the Awesome Bar on my desktop takes quite a long time despite the decent config, the laptop is even slower. The experience is quite unresponsive. I figured if I cleared the history up a little bit, I might avoid creating a new profile to speed things up. The question itself: to illustrate: Is there a way to delete all history entries that have been visited fewer than x (let's say 5) times and at the same time the recent visit is fewer than y (let's say 120) days old? afaik the history file is some kind of SQL database, but I'm not really sure how the data is saved, if there's a "safe way" to edit it and what the query to do what I need would look like. Thanks in advance for any help. I kept browsing through previous SuperUser questions to see if I could find relevant information. "In my Firefox profile directory, there is a filed named places.sqlite. Opening it with sqlite reveals (amongst others) the tables moz_places and moz_historyvisits. It seems that moz_historyvisits uses the primary of moz_places to refer to the URLs." As I'm unfamiliar with databases, I don't really understand the way the two tables mentioned in the quote are related. screenshot of a part of the tables I've noticed the visit_count is in a standard format, making it easy to work with. The last_visit_date looks encrypted to my naked eye, but I can't see in which way. Hope that helps, I'm at my wits' end.

  Read the article

• What is the fastest way to resize a large partition?

  - by Jook

  Due to a new HDD-Configuration I am currently handling larger backup/resize tasks with partitions between around 900MB, wich are 70-90% full. some background: First thing I've noticed was, that the Acronis-WesternDigital TrueImage was extremly slow while running it under Windows 7, even though on high priority. To create a normal backup for 650gb of data (900gb partition), it would have taken 3 days! The same task done with the boot-cd version of this acronis version took about 2 hours (SATA3 copy from one disk to another, both around 110MB/s). Now, after I have done all my backups, I've wanted to remove some obsolete partitions and resize the leftovers to full hdd size. Of course, usually this takes quite some time - in this case for this 900gb partition, to extend it to 931 (30gb+ from front, 1gb+ from end), it will take around 6 hours (using gparted)! Had I new that erlier, I would have just restored the image. But no - first it showed a reasonable time of 1:45h and 0 of 1 operations, but after finishing 1:45h it started again, only this time with 4h to go, still 0 of 1 operations, but now it was copying instead of moving. Question: However, why has it to be this slow to resize a partition? I am asking for a good explanaition. This has bugged me, since I started partitioning - why does it require to copy all the data around, can't it just stay in place?!

  Read the article

• DNS NAmeserver Aname and cname records

  - by David

  Hi - I am inexperienced in the configuration of DNS and have an issue with dominan hosting set up. I have two domains 'www.mydomain1.com' and 'www.mydomain2.com', with mydomain2 pointed at the same place as mydomain1. The domains were passed to me recently by the person who previoulsy controlled them. I have an account with fasthosts in the uk. When I accepted the domains I could not access the DNS settings and enquired with fasthosts as to why. The replied saying 'The delegate hosting option for both domains were enabled and this is the reason why you were unable to find the option to edit the advanced DNS records. I have now disabled the delegate hosting option so you can now edit the advanced DNS records for both domains in your account.' When i log into the fasthost control panel now i can access the DNS controls but both domains have no A Record of Cname record set up. I am concerned that fasthosts have blatted the previous Nameserver entries and set me up on theirs but not added any record. 'www.mydomain1.com' currently still works but 'www.mydomain2.com' does not find the site anymore. i am worried i will lose mydomain1 to as teh dns changes filter through the system. my webhosting is at 'xxx.xxx.xxx.xxx/mydomain1.com/' and this is where I want both domains to point. Any advice would be much appreciated. one thing which is confusing me is that because I am on a shared server I have to put 'xxx.xxx.xxx.xxx/mydomain1.com/' to get to my site rather than just 'xxx.xxx.xxx.xxx'. The form on fasthosts for the aname record only allows an IP to be entered - does it add the mydomain1.com/ onto the end itself? Thanks for any help given - I'm quite worried about this David

  Read the article

• Acer recovering windows vista

  - by Charlie Pigarelli

  My computer history is very long even of my computer has 4 years of life. An year ago I installed Windows 7 on this acer m1610 that had Vista before. My technic left me 2 recovery disc for "acer vista" before updating it to Windows 7. Then the computer had some trouble. The graphic card broke and we decided to use another computer. Yesterday I had the great idea to fuse the two computer to have a better one... So I moved the graphic card of the latter computer to the acer and everything gone well. Then the trouble of speed, it had before, come back. So I decided to reinstall the very first Windows: Vista back again. I booted the computer with those 2 DVD-R my technic left me and at the end of the process it asked me to insert "the backup cd number one or the system disk". I found 2 original Acer "Blank Recovery Disc" DVD-R and tried with those: rejected. Tried with empty DVD-+R: rejected. I tried with CDs: rejected. I don't have any system disc with me. Except for those 2 DVD-R my technic left me. What am I supposed to do now? I even tried with these fantomatic alt+f9/f10 that should start the recovery without any disc... But nothing happened. PS: the installation cannot complete if I do not insert the right disk. (The recovery disc uses Acer eRecovery Management as recovery software.

  Read the article

• Missing boot files in Windows 8

  - by Alex F. Sherman

  I had a partition with Windows 8 Release Preview, Windows' System Reserved partition and the empty space of the beginning of disk. I moved two partitions to the beginning of disk using Ubuntu Live CD and GParted. After that, the Windows Loader didn't boot and throw an error about missing files. I fixed it using the commands: bootsect /nt60 sys /force /mbr bootrec /rebuildbcd bootrec /fixboot bootrec /fixmbr When I used "Automatic repair" option from "Advanced boot" menu, it throw an error like: Windows can't fix your boot problems. For more information see file C:\Windows\System32\LogFiles\Srt\SrtTrail.txt In this file I found a description of the system repair actions and at the end of file: Boot status indicates that the OS booted successfully. Now, when I use the Advanced boot menu from Windows 8 (PC settings - General - Advanced startup) I receive an error: Restart your PC to try again. It looks like something didn't load correctly. Restarting might fix the problem. If this happens more than once, you might also be able to find help by searching online for the specific error code. Erorr code: 0x8007090. 0x80070490 is the error code ERROR_NOT_FOUND. What are the missing boot files and how can I restore them? List of files in System Reserved Partition: B:\bootmgr B:\BOOTNXT B:\Boot\BCD B:\Boot\BCD.LOG B:\Boot\BCD.LOG1 B:\Boot\BCD.LOG2 B:\Boot\BOOTSTAT.DAT B:\Boot\Fonts B:\Boot\memtest.exe B:\Boot\qps-ploc B:\Boot\Resources B:\Boot\Resources\bootres.dll and many *.mui and *.ttf files.

  Read the article

• SQL 2005 Install completly broken on laptop.

  - by ProfKaos

  My problems started when I set up an exploratory domain controller at home. During that process, I changed the name of my laptop, from 'erisia' to 'erisia-laptop', and this resulted in me losing my admin account on SQL Server 2005 on my laptop. SQL Server seems to store the machine name as part of the user name, so now my local admin account is 'erisia-laptop\brady', which SQL server didn't recognise. I thought I'd cut my losses and just re-install SQL 2005, but the first install was aborted, so I tried a complete uninstall, followed by the new install. The latter didn't work while the former worked way too well. Now every attempt at installing SQL Server 2005 SP2 on my laptop running XP SP3 ends in sadness, with MSXML6 being the cause, because it won't install on this OS version. WTF? Does anyone know what I can do to get SQL 2005 installed? It's the only full admin DB tool I have. SQL 2008 Express that installed with VS 2010 Beta 2 doesn't allow much server admin.

  Read the article

• Spotlight actually searching every file on "This Mac"

  - by Cawas

  I know of 2 ways to search for any file in your machine using Finder (some say it's Spotlight) and no Terminal. To prevent answers / comments about Terminal, I consider it either for scripting something or as last resource. It's not practical for lots of usages. For instance, if you want to find something to attach to a mail, or embed in iTunes or any other app, you can just drag n' drop one or many of them. Definitely not practical to do under Terminal. There are many cases of use for any, but the focus here is Graphical User Interface. Well, the 2 ways basically are: Press Cmd + Opt + Spacebar and type in your search. Press the + button, select "System files" and "are included". This is so far my preferred way, but I'm not sure it will go through every file. Open Finder, press Cmd + Shift + G and/or select just one folder. Type in your search and select the folder rather than "This Mac". This will bring files not shown in "This Mac" if you select a folder outside of the default scope. Thing is, none of those is really convenient or have the nice presentation from regular Spotlight, which you get from Cmd + Spacebar and just typing. And, as far as I've heard, the default behavior on Spotlight in Tiger was actually being able to find files anywhere. So, is there any way to make the process significantly simpler? Maybe some tweak, configuration or really good Spotlight alternative? I'd rather keep it simple and tweak Spotlight.

  Read the article

• How to read an Excel file, get and set the information using POI

  - by user1399713

  I'm using Java to read a form that is in an Excel spreadsheet that the user fills in with information about geometric shape. Ex: Shape :_________ Color :_________ Area: _________ Perimeter:________ So far the code I have can I can read what I want in the form and print out the values of Shape, Color, Area, Perimeter. public class RangeSetter { /** * @param args * @throws IOException */ public static void main(String[] args) throws IOException { FileInputStream file = new FileInputStream(new File("test2.xls")); //C:\Users\Yo\Documents // Setup code String cname = "Shape"; HSSFWorkbook wb = new HSSFWorkbook(file); // retrieve workbook // Retrieve the named range // Will be something like "$C$10,$D$12:$D$14"; int namedCellIdx = wb.getNameIndex(cname); Name aNamedCell = wb.getNameAt(namedCellIdx); // Retrieve the cell at the named range and test its contents // Will get back one AreaReference for C10, and // another for D12 to D14 AreaReference[] arefs = AreaReference.generateContiguous(aNamedCell.getRefersToFormula()); for (int i=0; i<arefs.length; i++) { // Only get the corners of the Area // (use arefs[i].getAllReferencedCells() to get all cells) CellReference[] crefs = arefs[i].getAllReferencedCells(); for (int j=0; j<crefs.length; j++) { // Check it turns into real stuff Sheet s = wb.getSheet(crefs[j].getSheetName()); Row r = s.getRow(crefs[j].getRow()); Cell c = r.getCell(crefs[j].getCol()); if (c!= null ){ switch(c.getCellType()){ case Cell.CELL_TYPE_STRING: System.out.println(c.getStringCellValue()); } } } } What I want to do is to create a method that gets the that information and another that sets it. So far I can only print to the console

  Read the article

• Suggestions for Windows 8 migration [closed]

  - by Big Endian

  I'm thinking of migrating to Windows 8. At first I hated it, but I'm pretty sure the Windows 8 model is the future, and I don't particularly want to end up hating the future like my parents, frustrated and bewildered by anything past Windows XP. I'm currently running Windows 7 and my system has been accumulating some problems. It's probably an accumulation of issues from installing too much software, changing firewall settings, installing Ubuntu alongside Windows, and... well I'm not sure, but my computer has been buggy in unexpected ways lately (freezing and unfreezing, display driver crashing and recovering, and what I call "deep freeze/thaw cycle" where the mouse won't even move for a while). I'm good at solving computer problems, but I can't seem to get to the root of these and my best idea for fixing them is making sure I've backed up every file then re-installing the entire OS. Luckily for me, a new OS is just around the corner so this would be a good time to get two things out of the way at once. The problem I see is that the upgrade options I see are all "seamless". I don't want a seamless upgrade. I want to wipe the slate clean and start all over. Does this mean I will have to buy a full, new copy of Windows 8 rather than one of the cheaper upgrading options? Or does it not make since for me to go to Windows 8 given that I have a laptop, not a tablet? Maybe I should just re-install Windows 7, or even call good enough good enough, try to eliminate the bugs, and start with a fresh slate in 2-3 years after this computer eventually dies entirely from (inevitable) hardware failure. What would be the advantages or disadvantages and costs of each option, how would I go about upgrading to Windows 8 if that's the option I choose, and what is your personal opinion about my situation?

  Read the article

• Use Alladin eToken with ThunderBird and other tool

  - by Yurij73

  I'm looking for an example on how to setup the eToken PRO Java device to work with Mozilla Thunderbird and with other Linux tool such as PAM logon. I installed distributed pkiclient-5.00.28-0.i386.RPM from the official product page eToken Pro but that tool only handles importing/exporting certificates on the device. I read a glance an old HOWTO from eToken on Linux, but I couldn't install pkcs11-lib for this device as recommended for Thunderbird use this crypto device. It seems my usb token isn't listed in system, unless lsusb show it, so that is the matter modutil -list -dbdir /etc/pki/nssdb Listing of PKCS #11 Modules NSS Internal PKCS #11 Module Blockquote slots: 2 slots attached Blockquote status: loaded Blockquote slot: NSS User Private Key and Certificate Services Blockquote token: NSS Certificate DB Blockquote CoolKey PKCS #11 Module Blockquote library name: libcoolkeypk11.so Blockquote slots: 1 slot attached Blockquote status: loaded Blockquote slot: AKS ifdh [Main Interface] 00 00 token: is my token absent? on other hand i don't know which module is convenient to Java Pro, does CoolKey does all the job well? It seems Java token is too new hardware for Linux? there is excerpt from /etc/pam_pkcs11.conf #filename of the PKCS #11 module. The default value is "default" use_pkcs11_module = coolkey; screen_savers = gnome-screensaver,xscreensaver,kscreensaver pkcs11_module coolkey { module = libcoolkeypk11.so; description = "Cool Key"`

  Read the article

• Outlook 2007 font sizes

  - by Flack

  Hello, Something really strange seems to have happened to my Outlook 2007. Everything was working fine for a long time now but at the end of today, all of a sudden, all of the fonts in Outlook are messed up. The font size of mails I write is huge (I am not zoomed in) and the font sizes of the buttons are big too, specifically the "Send", "To", and "Cc" buttons. I tried changing the font sizes through Outlook, but some of the buttons on the "Mail Format" tab in Options are not working, mainly the "Stationary and Fonts" button. I hit it but no window opens. This is all happening on my x64 machine. I took a look at my x32 machine, which also has Outlook 2007 installed and everything is ok there. Below is a link to an image comparing the broken, large font Outlook (top of picture) and the normal, working outlook. The text in the mails I compose is also abnormally large in the broken Outlook. Big font Outlook buttons. Any ideas? This came out of no where after a few months of no problems. Thanks.

  Read the article

• Vista gets stuck in an endless loop while booting

  - by Mason Wheeler

  I put my laptop to sleep last night, and when I woke up this morning... it didn't. So I tried to reboot, and everything went fine until it got to the Vista splash screen, where it's supposed to display the logon. Here, it hits an endless loop: Display the cursor with the blue spinny thing that replaced the hourglass, for 5-10 seconds Display "Please wait..." for about half a second Screen flashes to black, then quickly back to the Vista splash screen Goto step 1 The whole time, my hard LED is on almost non-stop. I can boot into Safe Mode... sometimes. Sometimes it'll load all the drivers, then sit there for about 10 minutes, spinning the hard drive non-stop, then reboot with no warning. I tried booting to Last Known Good Configuration. Didn't fix anything. When I've managed to get into Safe Mode, I tried running CHKDSK. Didn't fix anything. I tried running System Restore to each of my last two restore points. Didn't fix anything either time. I ran a virus scan. Didn't find anything. I tried calling the manufacturer (Alienware), only to discover that my warranty expired last freaking week and now I can't get it fixed without paying exorbitant sums of money. I'm about at my wits' end here. Has anyone seen this problem before? Does anyone know how to fix it? Does anyone know a solution that does not involve reinstalling the OS and losing an entire year's worth of program installations, Windows Updates and configuring and tweaking things until it's working just like I want it to?

  Read the article

• Loop through several servers, find specific dlls , get the dll version, internal filename and path?

  - by Graham

  I am a newby to Powershell, and using PS v2. I can see the massive potential it has, but I just can't get the following code to work fully. I am trying to end up with a csv file that contains the wild carded required dlls in the GAC_MSIL or sub-directory, get the dll version, internal filename and path, and the server IP address. The code is below, and it is in single line format because it appears easier to remote onto one of the servers in the server farm and run the single line from that console, ue to security log-ins etc. The code has produced a set of results, but only for the last server, it probably does the first server, then overwrites it but I am not sure about that. I have done a lot of reading about using arrays, and custom objects, and had a go at doing that, but my scripting skills in PS are not yet up to it. Code: $out = "Ouput_dll_ver_results.csv";foreach ($server in '11.222.33.123', '11.222.33.124') {$VersionInfo = (Get-ChildItem \$server\C$\windows\assembly\GAC_MSIL -recurse -Include abc*.dll,def*.dll,ghi*.dll,jkl*.dll | Where-Object { $.FullName -notmatch "\windows\assembly\temp\" })}; $VersionInfo | %{Get-Command $.FullName} | select -expand File* |Export-Csv $out Can you please advise if/how the above code can be corrected, and if not, what alternatives do I have to get the information I need. Many thanks in advance. Graham

  Read the article

• Need Info on the Hidden Switch in SET - "/S" How to implement

  - by ttyl

  I am having some problems doing a proper search of "SET/S" or "SET /S" on google and other search providers. The difficulty arises with the SLASH "/", it is commonly used in search engines to add a "nearness" to the search parameter. I have found no way to escape the SLASH when searching for a SLASH. For those on this community, try searching this domain with the two search terms listed above. It just doesn't work, it ends up looking for SET S instead. But I digress. So Im asking the uber-guru's on this board to help me find out about the documentation of /S and how to implement SET /S in a batch file. SET is an internal DOS/cmd commandand allows many things incuding prompting the user, integer math and writing environment strings. in looking at this link: http://www.robvanderwoude.com/os2set.php it appears that the /S is only for OS2 but im thinking that this might not be the case, due to this: http://www.dostips.com/forum/viewtopic.php?t=2704, apparently used with substings and macros. any help is much appreciated

  Read the article

• How can I fix my vista PCs screen resolution and refresh rate

  - by Antony Scott

  I have a media PC running media portal hooked up to my HDTV via HDMI. The TV is a couple of years old now, so only supports 1080i, which is 1920x1080@25Hz. I've got it connected to my PC via a HDMI compatible AV receiver. If I power up the amp (wait for it to boot fully) followed by the TV| and finally the PC, all is well and I get a picture. If I deviate from that sequence, or don't wait for the amp to book up fully, or even switch the amp to another video input (for example, my PS3). The PC sees this and defaults the screen resolution/refresh rate to 1920x1080@60Hz. So, I end up with a blank screen. To fix this I have to use UltraVNC from a PC and change the refresh rate back to 25Hz. So, is there a way to turn off that auto detection, or to manually define what resolution/refresh rates the monitor can do. I'm using the on-board Radeon 3200 video and do not have any of the AMD software installed as it seems to cause problems with video playback. So, I'm looking for a native vista fix, or possible some 3rd party software.

  Read the article

< Previous Page | 585 586 587 588 589 590 591 592 593 594 595 596  | Next Page >