Search Results

Search found 19061 results on 763 pages for 'load factor'.

Page 589/763 | < Previous Page | 585 586 587 588 589 590 591 592 593 594 595 596 | Next Page >

Is the exhaust fan necessary?

- by Borek

On my new PC, the component making the most noise is the rear exhaust fan on my case (it is the only exhaust fan in my PC). I tried to disconnect it and watched temperatures in SpeedFan and CPU was usually at about 35C, peaking to about 50C when the system was under load - this doesn't look too bad. So I'm considering that I'll leave the exhaust fan disconnected permanently after which the computer is very quiet - the only noise-making components are Arctic Cooling Freezer 7 Pro Rev.2 (CPU fan) and PSU fan (Enermax Pro 82+), both being quiet enough as far as I can tell. (My GPU has a passive cooler.) Also, those 2 components are moving parts so will provide some air flow in the case and, even better, PSU fan sucks the air out of the case so it kind of is an exhaust fan in itself. Does anyone run with the exhaust fan disconnected? You don't have to tell me that it's always better to have more air flow than less, I know that, but the noise is also a consideration for me and temperatures around 40C should be fine shouldn't they? (I might also consider getting a quieter case fan but I'm specifically interested in your opinion on the no exhaust fan scenario.)

Read the article
On AWS EC2, Unable to run sudo command after modifying permissions to /usr folder

- by Kayote

All, We have searched quite a bit and a few of 'Eliah Kagan's' posts are great about getting access back to sudo. However, our server is on AWS EC2 & I am a complete newbie to this. We are trying to setup Cronjobs for backing up our server data. What we did: Using Putty, we created a script file: usr/share/site-db-backup/backupToS3.php, however, Ubuntu was not saving the changes we made as it reported we did not have permission as user 'Ubuntu'. Error details are: "Upload of file backupToS3.php was successful but error occurred while setting the permission &/ or timestamp. If the problem persists, turn on 'ignore permission errors' option. Permission denied. Error code: 3 Request code 9" So, we ran the command "sudo chmod -R a+rwx /usr" for granting permission to the folder 'usr'. However, now whatever sudo command is run, we get the error: "/usr/lib/sudo/sudoers.so must be only be writable by owner. fatal error, unable to load plugins." We are complete newbies to Ubuntu & EC2 so do need step by step guidance of how to get sudo back & successfully write to the Crontab script sitting in 'usr/' folder.

Read the article
Can't write to samba share

- by Tiddo

I try to setup a samba file server, but whatever I do I can't get write access to work (reading works fine). This is my current situation: I have a local fileserver with 3 harddisks mounted at /mnt/share/disk<nr>. 2 of these use the ext4 filesystem, the third one is ntfs. This file server runs Fedora 18 32-bit. The root folders of these harddisks are owned by superman:superman, and testparm outputs the following: [global] workgroup = WORKGROUP netbios name = FILE_SERVER server string = Samba Server Version %v interfaces = lo, eth0, 192.168.123.191/8 log file = /var/log/samba/log.%m max log size = 50 unix extensions = No load printers = No idmap config * : backend = tdb hosts allow = 192.168.123. cups options = raw wide links = Yes [share] comment = Home Directories path = /home/share/ write list = superman, @users force user = superman read only = No create mask = 0777 directory mask = 0777 inherit permissions = Yes guest ok = Yes I've tried a lot to get this to work: the disk are chmodded to 777, I've tried turning off selinux, I've added the samba_share_t label to the disks and as can be seen in the above output I tried to make the smb config as permissive as I could, but still I cannot write to the share (tried from Windows 7 and another Fedora installation). What can I try to be able to write to the shares? EDIT: The replies I got so far are mostly concerned with the smb.conf. I have however tried a lot of different setup, ready made configs, and solutions to similar problems for the smb.conf file, so I suspect that the real problem is somewhere else.

Read the article
IIS 7.0 - responses throttled to 500ms blocks?

- by Julia Hayward

Scenario: ASP.NET MVC wep app sitting on my local machine (Vista Ultimate, IIS 7.0), nothing going on except one user (me) logged in and viewing an index page. The page includes 9 dynamic images drawn from the underlying DB and returned from a controller action. I have got the actual processing time for these images down to 15ms each. Turn on Firebug and watch the page load. What I see is 9 requests for images firing off together – no surprise – but four come back to me almost immediately; two more after 0.5s; another after 1s; then at 1.5s and 2s. Logging on the server side suggests the individual responses are still only taking 15ms. So it appears IIS is queueing things up into 500ms chunks. (Repeating the experiment produces different results, but each time the images return in similar blocks – you might get three in the first group, then three at 0.5s, two at 1s etc, for example – and it’s always at 500ms intervals, not anything else.) It’s also repeatable cross-browser, and it’s not repeatable with other forms of content. I haven't found any particular mention of this problem out there, so I'm sort of assuming it's not an IIS bug, so is it: i) IIS on desktop OSs deliberately does it, to make you use server OSs in production? ii) There is some magical setting that has eluded me for as long as I’ve known IIS? iii) Something peculiar to MVC or SQL Server 2008? or something else?

Read the article
Access Existing Linux Installation from Windows Bootloader - Linux Installed and Then Windows 7

- by nicorellius

My hard drive is failing. I installed a new drive, and the installed Ubuntu 12.04 to try to rescue data. Realized that I wanted to install Windows and just access drives without transferring data (there are loads of it). I then installed Windows 7. Now my drive only boots to Windows 7. How do I access Linux and make Windows boot-loader load Linux? I originally thought I would just not use the Ubuntu installation but now I think I want it to be a dual boot system. What are good boot-loaders to install for this kind of dual boot situation? Can I accomplish this with BCDEdit? If I would have done this the other way (Windows first, then Linux) everything would be fine, but I didn't and now I'm trying to fix this. The problem I have is that I don't really know how to boot into Linux to retrieve any files I need. I guess using the disc would work, but I'm not sure how to go about this.

Read the article
IIS and ASP.NET

- by sam

i'm trying to add asp.net feature on windows 7 i tried to turn it on using turn windows features on or off but it fails every time so i download web platform installer and try it that way and it fails also next i uninstall .net framework 4 restart again! and reinstall it and try again the previous steps but it fails the same i need this installed so i can view it on iis7 anyone know what i can do with this to get it working i've searched and searched and everything fails i get this error on the web platform installer Failed with 0x80070643 – Fatal Error during installation please help i cant do my work with out it working :( ok i did a few things now get this error Server Error in '/pulse' Application. Parser Error Description: An error occurred during the parsing of a resource required to service this request. Please review the following specific parse error details and modify your source file appropriately. Parser Error Message: Could not load type 'pulsesite.MvcApplication'. Source Error: Line 1: <%@ Application Codebehind="Global.asax.vb" Inherits="pulsesite.MvcApplication" Language="VB" % Source File: /pulse/global.asax Line: 1 Version Information: Microsoft .NET Framework Version:4.0.30319; ASP.NET Version:4.0.30319.1 i know its ust about changing the code but i'm not good with c# anyone know how?

Read the article
How do I prevent spawning of zombie-like apache2 processes on Dreamhost VPS?

- by Jonathan Hayward

I have had a website for months or longer on a DreamHost VPS, and I have had vague memories on, in initial setup, having to turn off some customized Apache under /dh to get a standard Apache 2.x to work with. Things have been going along on an even keel, when I started making some changes lately and I found that when I tried to bounce Apache (/usr/sbin/apachectl restart), it couldn't bind to port 80, and my site had been converted from a big literature site to a small parking site. I tried to see what was listening on 80, and it was a DreamHost-customized Apache that had spawned. I killed all of them, restarted Apache, and changed the parent directory under /dh to mode 000. That was a day or two ago. I was bouncing Apache again in trying to get a new site to load under HTTPS, and I found that once again DreamHost's apache had spawned, from the directory I set to mode 000, and once again converted my site to a parking page. I renamed the directory, but I am very skeptical of whether I have permanently killed the DreamHost-customized Apache. Besides duct tape options like a crontab to kill and delete each minute, how can I permanently turn off the Apache processes that are spawning from a location under /dh and interfering with standard Apache? What should I be doing that I am not? Can DreamHost's technical support stop the interference? Thanks,

Read the article
High CPU usage in my digitalocean droplet

- by Ibrahim Azhar Armar

I am experiencing high CPU usage here is the stats i got from server, the consumption after every restart in 15 minutes go upto 100%, what could go wrong? I have a wordpress copy installed on the server which does not have much traffic, here is the stats that i got from using top command in server. top - 11:46:02 up 12 min, 3 users, load average: 40.89, 16.03, 6.11 Tasks: 132 total, 41 running, 91 sleeping, 0 stopped, 0 zombie Cpu(s): 24.3%us, 61.5%sy, 0.0%ni, 0.0%id, 4.0%wa, 0.0%hi, 0.0%si, 10.2%st Mem: 2050896k total, 1988656k used, 62240k free, 284k buffers Swap: 0k total, 0k used, 0k free, 4712k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 31 root 20 0 0 0 0 R 39 0.0 1:35.53 kswapd0 899 root 20 0 15988 172 0 S 14 0.0 0:05.00 irqbalance 418 syslog 20 0 243m 600 0 S 13 0.0 0:06.85 rsyslogd 944 mysql 20 0 1320m 53m 0 S 12 2.7 0:21.15 mysqld 2357 root 20 0 17344 532 164 R 11 0.0 0:14.27 top 960 root 20 0 246m 3816 0 S 3 0.2 0:08.18 php5-fpm 2431 www-data 20 0 344m 64m 908 R 2 3.2 0:04.23 apache2 2435 www-data 20 0 304m 63m 836 R 2 3.2 0:03.43 apache2 2413 www-data 20 0 349m 63m 920 R 2 3.2 0:07.51 apache2 2465 www-data 20 0 349m 64m 944 R 2 3.2 0:05.04 apache2 2518 www-data 20 0 307m 41m 1204 R 2 2.1 0:01.37 apache2 2406 www-data 20 0 346m 56m 1144 R 2 2.8 0:03.76 apache2 2456 www-data 20 0 345m 55m 1184 R 2 2.8 0:02.67 apache2 2373 www-data 20 0 351m 63m 784 R 2 3.2 0:11.09 apache2 2439 www-data 20 0 306m 35m 916 R 2 1.8 0:02.51 apache2 2450 www-data 20 0 345m 55m 1088 R 2 2.8 0:02.96 apache2 2486 www-data 20 0 299m 10m 876 R 2 0.5 0:01.19 apache2 2523 www-data 20 0 300m 27m 796 R 2 1.4 0:00.99 apache2

Read the article
esxi 5 monitoring

- by user134880

I'm new to esxi/vmware world. Have few question about monitoring esxi host. Now I'm using trial versian esxi 5.1 I can see performance charts in vShpere client. Cool. But I want to export this raw data (raw - I mean cvs,txt or some format which I can parse later) to other server to be able to parse this data later and create custom charts. (please do not advise to try vCenter, I need custom charts etc.) I could run esxtop in batch mode and use this data... But... How does vShpere client performance charts work? Where client takes data for charts? So if I will use esxtop batch mode it will add extra load to server. Is it possible to use same source as vSphere client use for charts? There is /var/lib/vmware/hostd/stats/hostAgentStats-20.stats file. Its looks like it is binary format. As I understood it is exactly data which I need?!?! Any ideas how to parse it? Thanks! PS: maybe some one know where to find, if there is one, info about processes running on esxi host?

Read the article
Vyatta internet connection + hosted site on same IP

- by boburob

Having a small issue setting up a vyatta. The company internet and two different websites are both on the same IP. Server 1 - Has websites hosted on ports 1000 and 3000 and also has a proxy server installed to provide internet connection to the domain Server 2 - Has a website hosted on ports 80 and 433 The vyatta is correctly natting the appropriate traffic to each server, and allowing the proxy to get internet traffic, however I have a problem getting to the websites hosted on these two servers inside the domain. I believe the problem is that the HTTP request is being sent with an IP, eg: 12.34.56.78. The request will reach the website and the server will attempt to send the request back to the IP, however this is the IP of the Vyatta, so it has nowhere else to go. I thought the solution would be something like this: rule 50 { destination { address 12.34.56.78 port 1000 } inbound-interface eth1 inside-address { address 10.19.2.3 } protocol tcp type destination } But this doesnt seem to do it! UPDATE I changed the rules to the following: rule 50 { destination { address 12.34.56.78 port 443 } outbound-interface eth1 protocol tcp source { address 10.19.2.3 } type masquerade } rule 51 { destination { address 12.34.56.78 port 443 } inbound-interface eth1 inside-address { address 10.19.2.2 } protocol tcp type destination } I am now seeing traffic going between the two with Wireshark, but the website will still fail to load.

Read the article
Display with intel integrated graphics, bitcoin mine with Radeon 6950

- by karategeek6

I'm on Ubuntu Linux 11.04 64 bit. I have an intel i5 with integrated graphics and a Radeon 6950, with one monitor. I would like to run my graphics on the integrated card, and run bitcoin mining on the 6950. I have bitcoin mining working when I use the 6950 for both display and mining. Every time I try and and use the integrated graphics instead, OpenCL doesn't recognize my 6950. Using aticonfig --initial when using the integrated graphics for display breaks things. So I used the xorg.conf it created as a basis and tried to manually edit it. I really don't know what I'm doing, though. My last attempt is given below. The graphics ran off the integrated card, but the 6950 wasn't recognized. Any help would be greatly appreciated! xorg.conf: #Section "ServerLayout" # Identifier "Intel Layout" # Screen "Default Screen" # Identifier "aticonfig Layout" # Screen "aticonfig-Screen[0]-0" # Screen 0 "aticonfig-Screen[0]-0" 0 0 #EndSection Section "Module" Load "glx" EndSection # Intel Section "Device" Identifier "Intel Integrated Graphics" Driver "intel" BusID "PCI:0:2:0" EndSection Section "Monitor" Identifier "Default Monitor" Option "VendorName" "Monitor Vendor" Option "ModelName" "Monitor Name" Option "DPMS" "true" EndSection Section "Screen" Identifier "Default Screen" Device "Intel Integrated Graphics" Monitor "Default Monitor" DefaultDepth 24 EndSection # ATI Section "Device" Identifier "aticonfig-Device[0]-0" Driver "fglrx" BusID "PCI:1:0:0" EndSection Section "Monitor" Identifier "aticonfig-Monitor[0]-0" Option "VendorName" "ATI Proprietary Driver" Option "ModelName" "Generic Autodetecting Monitor" Option "DPMS" "true" EndSection Section "Screen" Identifier "aticonfig-Screen[0]-0" Device "aticonfig-Device[0]-0" Monitor "aticonfig-Monitor[0]-0" DefaultDepth 24 SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection

Read the article
Connection problems via Wifi (multiple devices)

- by Kelvin Farrell

I'm having connection issues with my router (Linksys WRT610N) at home. There are a number of things that are happening (may be more, this is just what I've mainly noticed)... 1) Using my laptop (Macbook Pro OSX Lion), I am unable to complete any operations with my external FTP server, hosted with FatCow. I can connect to it, navigate through all the files, but when I try to edit/delete/add a file the operation times out. EVERY time. I've used two other Wifi connection on my laptop and neither have this issue. 2) I am unable to upload photos/videos to Facebook or Twitter using my phone (Samsung Galaxy S2) or my tablet (HP Touchpad - CM9). Neither am I able to upload files to Dropbox via either of the devices. Same thing happens in all situations; the upload will begin and it will just hang on 0% forever. After about 10 mins I am always forced to disconnect the Wifi to stop the action. 3) My laptop is having slow internet speed, even though we are on 20mb broadband. Speedtests say I'm getting a good connection and my Ping is good, but when using streaming services like Spotify, it takes forever to load a page and frequently stops to buffer whilst playing a song. Don't know if it's worth mentioning but I have no issues with my XBox (Ethernet), AppleTV (Wifi) or my girlfrield's phone (Nokia Lumia 800 - WP7.5) on the network. I'd really appreciate any help. This is driving me insane and is really affecting both my working and leisure use of the internet.

Read the article
Centos Server/MySQL server problem

- by Jake

Hello all, I currently run a website we get about 15,000-20,000 hits a day. We currently run a very active forum, that is hosted using Vbulletin software. We have 4.5 Million Posts, 80,000 Threads, with about 11,000 members of which just under a third is active all the time. Now I am running a Intel Xeon Quad Core (2.13Ghz) with 4GB of RAM, Centos 5.5 and running DirectAdmin on the box to manage it. I also run the current stable version of Apache, MySQL, and php. This is the only site that is hosted on this machine. Now during random times of day sometimes when it gets busy the server load can get to like 20, but this can also happen when we only have like 200 users active too. I dont understand what is causing these problems. Sometimes I get pages that can generate in .2 seconds other times it takes like 5-8 seconds. I have customized the my.cnf file and that has not helped out anything, I didnt know where else to turn so if anyone has any suggestions please let me know. Thank You In advance.

Read the article
Best tool for monitoring backups, etc. and trending statstics from that data

- by Randy Syring

I have done some research on nagios, opennms, and zenoss but am not confident that I have found what I am looking for. The main driving force for me right now is being able to monitor backups. This includes mysql, mssql, and eventually some file system backups. We have a tool that wraps the backup process for these different systems and collects statistics. So, items like: number of databases backed up size of db backup file size of db backup file compressed time to make backup time to zip file I want to be able to A) have notifications if the jobs are not run according to schedule B) be able to set thresholds on the statistics which would trigger notifications C) I want to be able to trend and graph the statistics I am planning on sending this information to the monitoring application through an HTTP POST. Or, the monitoring application could pull it from a log file as well. However, we will have other processes with other "arbitrary" (from the monitoring system's perspective) statics that will want to monitor and trend, so flexibility is very important. The tool or tools should also be able to do general monitoring and trending of network interfaces, server load, etc. Once we get the backup monitoring in place, we will want to include those items as well. Thanks.

Read the article
LG LW20 Express won't boot after hdd replace

- by Mika

My old laptop (LG LW20 Express) got a hdd failure and I replaced the hdd. Now the laptop won't boot from cd or usb. I'm trying to install ubuntu on it. When I turn the laptop on it shows me the startup screen but when it should be the time to load operating system it just gives a black screen and starts over. This loop continues until I shut down the laptop. I created the usb boot drive following this guide https://help.ubuntu.com/community/Installation/FromUSBStick/ I used my boot cd to install ubuntu on this machine I'm using right now. So at least the cd should work. From the BIOS I can see that my newly installed hdd is recognized and put as a secondary master. Also the cd and removable media are in the boot list before hdd. The laptop runs pretty hot. The fan is at full speed pretty soon after the laptop is turned on. Earlier I suspected that it would have been the almost broken hdd that would have produced that heat but there obviously is something else also. Any ideas what to check?

Read the article
PHP script not automatically updating when moved to another server

- by user32007

A friend built a ranking system on his site and I am trying to host in on mine via WordPress and Go Daddy. It updates for him but when I load it to my site, it works for 6 hours, but as soon as the reload is supposed to occur, it errors and I get a 500 timeout error. His page is at: jeremynoeljohnson .com/yakezieclub My page is currently at http://sweatingthebigstuff.com/yakezieclub but when you ?reload=1 it will give the error. Any idea why this might be happening? Any settings that I might need to change? Here is the top of the index.php file. I'm not sure which part of any of it is messing up. I literally uploaded the same code as him. Here's the reload part: $cachefile = "rankings.html"; $daycachefile = "rankings_history.xml"; $cachetime = (60 * 60) * 6; // every 6 hours, the cache refreshes $daycachetime = (60 * 60) * 24; // every 24 hours, the history will be written to // - or whenever the page is requested after 24 hours has passed $writenewdata = false; if (!empty($_GET['reload'])) { if ($_GET['reload']== 1) { $cachetime = 1; } } if (!empty($_GET['reloadhistory'])) { if ($_GET['reloadhistory'] == 1) { $daycachetime = 1; $cachetime = 1; } } if (file_exists($daycachefile) && (time() - $daycachetime < filemtime($daycachefile))) { // Do nothing } else { $writenewdata = true; $cachetime = 1; } // Serve from the cache if it is younger than $cachetime if (file_exists($cachefile) && (time() - $cachetime < filemtime($cachefile))) { include($cachefile); echo ""; exit; } ob_start(); // start the output buffer ?>

Read the article
Tomcat Custom MBean

- by Darran

Does anyone know how to deploy a custom MBean to Tomcat? So far I`ve found this http://www.junlu.com/list/3/8871.html. I copied my jar with my MBean to Tomcat lib directory so the Custom class loader should pick it up. I then followed the instructions but I kept getting the exception below. My MBean does definitely have a public constructor. If I removed the jar from the tomcat lib directory I get the same message which suggests its not picking up my jar or my jar is being loaded after the Apache MBean Modeler is running in Tomcat. 06-Aug-2010 12:14:23 org.apache.tomcat.util.modeler.modules.MbeansSource execute SEVERE: Error creating mbean Bean:type=Bean javax.management.NotCompliantMBeanException: MBean class must have public constructor at com.sun.jmx.mbeanserver.Introspector.testCreation(Introspector.java:127) at com.sun.jmx.interceptor.DefaultMBeanServerInterceptor.createMBean(DefaultMBeanServerInterceptor.java:2 at com.sun.jmx.interceptor.DefaultMBeanServerInterceptor.createMBean(DefaultMBeanServerInterceptor.java:1 at com.sun.jmx.mbeanserver.JmxMBeanServer.createMBean(JmxMBeanServer.java:393) at org.apache.tomcat.util.modeler.modules.MbeansSource.execute(MbeansSource.java:207) at org.apache.tomcat.util.modeler.modules.MbeansSource.load(MbeansSource.java:137) at org.apache.catalina.core.StandardEngine.readEngineMbeans(StandardEngine.java:517) at org.apache.catalina.core.StandardEngine.init(StandardEngine.java:321) at org.apache.catalina.core.StandardEngine.start(StandardEngine.java:411) at org.apache.catalina.core.StandardService.start(StandardService.java:519) at org.apache.catalina.core.StandardServer.start(StandardServer.java:710) at org.apache.catalina.startup.Catalina.start(Catalina.java:581) at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method) at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39) at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25) at java.lang.reflect.Method.invoke(Method.java:597) at org.apache.catalina.startup.Bootstrap.start(Bootstrap.java:289) at org.apache.catalina.startup.Bootstrap.main(Bootstrap.java:414)

Read the article
CentOS 6.3 Virtual under OpenVZ cannot ping, host lookups, outbound connections while postfix running

- by Paul Cravey

My best theory is that some kernel limit is being hit preventing outbound connections. We have tried basically everything from tcpdumps to provisioning an entirely new virtual server (we do not have this problem on any other virtuals), however the problem somehow carried over, even with new postfix build (working). Emails work, and outbound connections work, so long as postfix does not have too much going on. /proc/user_beancounters shows no limits being hit (show below). Nevertheless, pings fail even to IP addresses. TCP stack appears healthy. Load is low. No iowait. Flushed iptables already. Has anyone experienced anything like this? uid resource held maxheld barrier limit failcnt 3: kmemsize 166216365 170262528 9223372036854775807 9223372036854775807 0 lockedpages 0 0 9223372036854775807 9223372036854775807 0 privvmpages 285727 351885 9223372036854775807 9223372036854775807 0 shmpages 16933 17605 9223372036854775807 9223372036854775807 0 dummy 0 0 0 0 0 numproc 150 303 9223372036854775807 9223372036854775807 0 physpages 314156 326191 0 1280000 0 vmguarpages 0 0 9223372036854775807 9223372036854775807 0 oomguarpages 165355 165355 9223372036854775807 9223372036854775807 0 numtcpsock 89 172 9223372036854775807 9223372036854775807 0 numflock 22 76 9223372036854775807 9223372036854775807 0 numpty 1 2 9223372036854775807 9223372036854775807 0 numsiginfo 0 75 9223372036854775807 9223372036854775807 0 tcpsndbuf 2733472 4371752 9223372036854775807 9223372036854775807 0 tcprcvbuf 1798336 5427296 9223372036854775807 9223372036854775807 0 othersockbuf 491120 1000760 9223372036854775807 9223372036854775807 0 dgramrcvbuf 0 238728 9223372036854775807 9223372036854775807 0 numothersock 361 505 9223372036854775807 9223372036854775807 0 dcachesize 135941831 136114679 9223372036854775807 9223372036854775807 0 numfile 2905 4990 9223372036854775807 9223372036854775807 0 dummy 0 0 0 0 0 dummy 0 0 0 0 0 dummy 0 0 0 0 0 numiptent 8 9 9223372036854775807 9223372036854775807 0 [root@bni /]# ping 4.2.2.1 PING 4.2.2.1 (4.2.2.1) 56(84) bytes of data. --- 4.2.2.1 ping statistics --- 9 packets transmitted, 0 received, 100% packet loss, time 8493ms [root@bni /]# service postfix stop [root@bni /]# ping 4.2.2.1 PING 4.2.2.1 (4.2.2.1) 56(84) bytes of data. 64 bytes from 4.2.2.1: icmp_seq=1 ttl=53 time=8.63 ms 64 bytes from 4.2.2.1: icmp_seq=2 ttl=53 time=8.62 ms 64 bytes from 4.2.2.1: icmp_seq=3 ttl=53 time=8.63 ms 64 bytes from 4.2.2.1: icmp_seq=4 ttl=53 time=8.66 ms Outbound connections of all sorts fail when postfix is running.

Read the article
Windows 7 boot problem on a Lenovo Thinkpad Z61m 9450HAG

- by Matt Taylor

I recently did a full upgrade of Windows 7 on my Thinkpad. Everything worked fine after up until the second reboot (the first reboot after some updates installed worked OK). At second reboot time the system would just black screen before the Windows logo appears. Disk/wireless/power/battery lights are all lit and the disk light is active (flickering). However, if I remove my battery and boot with just power it boots fine and quickly, and everything is OK. Any help on why this won't boot with battery plugged in is greatly appreciated. I need to take this battery out on the road/trains, etc. A little more detail on this story. The battery I had inserted when doing the (failed) boot was a long life battery. I have not tried inserting this battery when Windows is logged in. I have another (normal life) battery that I have charged up within Windows. It has just got to 100% and I am about to reboot with it in. I am using the Lenovo power manager to diagnose the battery - all seems OK. I will report back shortly as to the outcome. OK, so I chose the reboot option from within Windows, the machine seemed to shutdown okay, but then stalled. It didn't turn off completely and didn't reboot, but just sat, with the fan humming, somewhere in between! I had to hold the power button in for a few seconds until the fan stopped and then hit the power button again to boot the machine from fresh. One good thing, with this battery (the normal one) it booted into Windows 7 the first time with a battery! So, now I have rebooting issues. I have 3 errors in the event log: A timeout was reached (30000 milliseconds) while waiting for the lxdxCATSCustConnectService service to connect. The lxdxCATSCustConnectService service failed to start due to the following error: The service did not respond to the start or control request in a timely fashion. The following boot-start or system-start driver(s) failed to load: cdrom Any thoughts?

Read the article
memory tuning with rails/unicorn running on ubuntu

- by user970193

I am running unicorn on Ubuntu 11, Rails 3.0, and Ruby 1.8.7. It is an 8 core ec2 box, and I am running 15 workers. CPU never seems to get pinned, and I seem to be handling requests pretty nicely. My question concerns memory usage, and what concerns I should have with what I am seeing. (if any) Here is the scenario: Under constant load (about 15 reqs/sec coming in from nginx), over the course of an hour, each server in the 3 server cluster loses about 100MB / hour. This is a linear slope for about 6 hours, then it appears to level out, but still maybe appear to lose about 10MB/hour. If I drop my page caches using the linux command echo 1 /proc/sys/vm/drop_caches, the available free memory shoots back up to what it was when I started the unicorns, and the memory loss pattern begins again over the hours. Before: total used free shared buffers cached Mem: 7130244 5005376 2124868 0 113628 422856 -/+ buffers/cache: 4468892 2661352 Swap: 33554428 0 33554428 After: total used free shared buffers cached Mem: 7130244 4467144 2663100 0 228 11172 -/+ buffers/cache: 4455744 2674500 Swap: 33554428 0 33554428 My Ruby code does use memoizations and I'm assuming Ruby/Rails/Unicorn is keeping its own caches... what I'm wondering is should I be worried about this behaviour? FWIW, my Unicorn config: worker_processes 15 listen "#{CAPISTRANO_ROOT}/shared/pids/unicorn_socket", :backlog = 1024 listen 8080, :tcp_nopush = true timeout 180 pid "#{CAPISTRANO_ROOT}/shared/pids/unicorn.pid" GC.respond_to?(:copy_on_write_friendly=) and GC.copy_on_write_friendly = true before_fork do |server, worker| STDERR.puts "XXXXXXXXXXXXXXXXXXX BEFORE FORK" print_gemfile_location defined?(ActiveRecord::Base) and ActiveRecord::Base.connection.disconnect! defined?(Resque) and Resque.redis.client.disconnect old_pid = "#{CAPISTRANO_ROOT}/shared/pids/unicorn.pid.oldbin" if File.exists?(old_pid) && server.pid != old_pid begin Process.kill("QUIT", File.read(old_pid).to_i) rescue Errno::ENOENT, Errno::ESRCH # already killed end end File.open("#{CAPISTRANO_ROOT}/shared/pids/unicorn.pid.ok", "w"){|f| f.print($$.to_s)} end after_fork do |server, worker| defined?(ActiveRecord::Base) and ActiveRecord::Base.establish_connection defined?(Resque) and Resque.redis.client.connect end Is there a need to experiment enforcing more stringent garbage collection using OobGC (http://unicorn.bogomips.org/Unicorn/OobGC.html)? Or is this just normal behaviour, and when/as the system needs more memory, it will empty the caches by itself, without me manually running that cache command? Basically, is this normal, expected behaviour? tia

Read the article
Understanding tcptraceroute versus http response

- by kojiro

I'm debugging a web server that has a very high wait time before responding. The server itself is quite fast and has no load, so I strongly suspect a network problem. Basically, I make a web request: wget -O/dev/null http://hostname/ --2013-10-18 11:03:08-- http://hostname/ Resolving hostname... 10.9.211.129 Connecting to hostname|10.9.211.129|:80... connected. HTTP request sent, awaiting response... 200 OK Length: unspecified [text/html] Saving to: ‘/dev/null’ 2013-10-18 11:04:11 (88.0 KB/s) - ‘/dev/null’ saved [13641] So you see it took about a minute to give me the page, but it does give it to me with a 200 response. So I try a tcptraceroute to see what's up: $ sudo tcptraceroute hostname 80 Password: Selected device en2, address 192.168.113.74, port 54699 for outgoing packets Tracing the path to hostname (10.9.211.129) on TCP port 80 (http), 30 hops max 1 192.168.113.1 0.842 ms 2.216 ms 2.130 ms 2 10.141.12.77 0.707 ms 0.767 ms 0.738 ms 3 10.141.12.33 1.227 ms 1.012 ms 1.120 ms 4 10.141.3.107 0.372 ms 0.305 ms 0.368 ms 5 12.112.4.41 6.688 ms 6.514 ms 6.467 ms 6 cr84.phlpa.ip.att.net (12.122.107.214) 19.892 ms 18.814 ms 15.804 ms 7 cr2.phlpa.ip.att.net (12.122.107.117) 17.554 ms 15.693 ms 16.122 ms 8 cr1.wswdc.ip.att.net (12.122.4.54) 15.838 ms 15.353 ms 15.511 ms 9 cr83.wswdc.ip.att.net (12.123.10.110) 17.451 ms 15.183 ms 16.198 ms 10 12.84.5.93 9.982 ms 9.817 ms 9.784 ms 11 12.84.5.94 14.587 ms 14.301 ms 14.238 ms 12 10.141.3.209 13.870 ms 13.845 ms 13.696 ms 13 * * * … 30 * * * I tried it again with 100 hops, just to be sure – the packets never get there. So how is it that the server does respond to requests via http, even after a minute? Shouldn't all requests just die? I'm not sure how to proceed debugging why this server is slow (as opposed to why it responds at all).

Read the article
How can I password protect an IIS directory with only FTP access?

- by Tony Adams

How can I password protect an IIS directory when I only have FTP access to the server? I can't adjust any IIS settings or add users or anything like that. The answer to: IIS Basic Authorization ala .htaccess/.htpasswd in apache does not help as I only have access to the server via FTP. I just need to password protect a directory. I've tried several variations of a web.config file. I can get a basic HTTP auth form to pop up when a user attempts to load a page from my test directory, but I can't configure the authentication part. The server complains that: Parser Error Message: It is an error to use a section registered as allowDefinition='MachineToApplication' beyond application level. This error can be caused by a virtual directory not being configured as an application in IIS. whenever I add an <authentication> section to my web.config. I'm grateful for any help anyone can offer. Edit: I don't know what version of IIS is running on this server, but here is the server tag from error messages: Version Information: Microsoft .NET Framework Version:1.1.4322.2490; ASP.NET Version:1.1.4322.2494

Read the article
Can't install xclip on Ubuntu 10.10

- by wildster

I'm trying to load an SSH key to Github from a new machine and this command is not working: sudo apt-get install xclip Reading package lists... Done Building dependency tree Reading state information... Done Package xclip is not available, but is referred to by another package. This may mean that the package is missing, has been obsoleted, or is only available from another source E: Package xclip has no installation candidate when I try: sudo aptitude install xclip Reading package lists... Done Building dependency tree Reading state information... Done Reading extended state information Initializing package states... Done No candidate version found for xclip No candidate version found for xclip The following partially installed packages will be configured: synaptics-dkms 0 packages upgraded, 0 newly installed, 0 to remove and 0 not upgraded. Need to get 0B of archives. After unpacking 0B will be used. Writing extended state information... Done Setting up synaptics-dkms (1.1.1) ... Loading new synaptics-1.1.1 DKMS files... Error! Cannot locate /usr/src/synaptics-1.1.1.dkms.tar.gz. File does not exist. dpkg: error processing synaptics-dkms (--configure): subprocess installed post-installation script returned error exit status 2 Errors were encountered while processing: synaptics-dkms E: Sub-process /usr/bin/dpkg returned an error code (1) A package failed to install. Trying to recover: Setting up synaptics-dkms (1.1.1) ... Loading new synaptics-1.1.1 DKMS files... Error! Cannot locate /usr/src/synaptics-1.1.1.dkms.tar.gz. File does not exist. dpkg: error processing synaptics-dkms (--configure): subprocess installed post-installation script returned error exit status 2 Errors were encountered while processing: synaptics-dkms Reading package lists... Done Building dependency tree Reading state information... Done Reading extended state information Initializing package states... Done Any idea how I can install this? Mucho thanks in advance

Read the article
Website Use Monitoring for 3 People

- by linkedlinked

I work in an IT startup with 2 partners, and I'm the programmer/IT guy -- in other words, the work horse. To make a long story short, I'm doing most of the work right now, while they spend all day on Facebook. That's OK, because they're paying my salary, but if the project fails, I'm sure they'll blame me for it (I'm doing my best to make sure that doesn't happen!), and I want some sort of recourse. I already have an app that blocks time-wasters on my local PC, and keeps logs of when the app is enabled (so I can say "I had Facebook blocked from 9am-5pm today.") Is there any way I can get a brief summary of the most heavily visited sites, split up by client PC? At the end of the month, I want to be able to say "You both load Facebook, on average, every 10 minutes. You spend hours a day on Youtube, and haven't opened up our bugtracker in weeks" and maybe have a nifty chart or graph to match it. We have a crappy D-Link router, and no IT budget. They are both on Windows Vista, I run Ubuntu Linux. I don't want to install any monitoring software on their PC, but I'm totally fine with, say, routing all the network traffic through my machine. I guess I can think of lots of ways to accomplish this (telnet into JSSH and list open tabs? log all the DNS requests, per-domain? even thinking of setting up a webcam on my desk and just keeping 5-minute snapshots...), I just don't really know where to start. Any advice is appreciated, thanks!

Read the article
Production monitoring for EC2 instances

- by Janine

I'm setting up my first production instance on EC2 and want to make sure I have all necessary monitoring in place. There are three different types of things I want to monitor: Is the instance running? EC2 instances can be terminated without warning if the underlying hardware fails, and as far as I know they aren't automatically restarted. So if not, start it back up. Is UNIX running properly? This is the usual stuff about CPU load, disk space, etc. Is the website responding? If not, restart it. I initially set up Nagios on a physical server outside the cloud, but it is really only helpful for item 2. It can tell me if the instance is gone or if the website is not responding, but as far as I can tell it can't execute any commands to fix the situation. My Googling on this subject has yielded a plethora of options - Cacti, Monit, God, Ganglia, and probably more I'm forgetting now. I don't have time to research them all. I am aware of Amazon's Cloudwatch but it doesn't seem to do anything that my Nagios installation doesn't already do. If you already have something like this in place, can you please share what has worked well for you?

Read the article

< Previous Page | 585 586 587 588 589 590 591 592 593 594 595 596 | Next Page >