Search Results

Search found 1856 results on 75 pages for 'kb'.

Page 59/75 | < Previous Page | 55 56 57 58 59 60 61 62 63 64 65 66  | Next Page >

• How can I change the binding order of network adapters in Windows 7?

  - by Chris Farmer

  The end goal here is that I am trying to install an Oracle 10g server on my Windows 7 x64 dev box. I use DHCP, and the Oracle installer is throwing up this warning: Checking Network Configuration requirements ... Check complete. The overall result of this check is: Failed <<<< Problem: The install has detected that the primary IP address of the system is DHCP-assigned. Recommendation: Oracle supports installations on systems with DHCP-assigned IP addresses; However, before you can do this, you must configure the Microsoft LoopBack Adapter to be the primary network adapter on the system. See the Installation Guide for more details on installing the software on systems configured with DHCP. I have installed the loopback adapter, but I am not sure how to make it the primary network adapter. I see this Microsoft KB article on the subject but it's Windows XP-oriented, and I can't seem to find a comparable one for Windows 7. Some of the options it talks about don't seem to be present in the views of the adapters that I see. So, how can I make the loopback adapter become the primary adapter?

  Read the article

• BSOD error 0x0000006B PROCESS1_INITIALIZATION_FAILED on boot

  - by DontCare4Free

  I reinstalled League of Legends because the patcher always gave me an error. However, out of complete stupidness I didn't uninstall the old installation first because I thought that it would simply replace the files. However, when the installer bar got to 100% it simply minimized. Then I closed the application from the task manager. I tried uninstalling it after a failed attempt to start it up. The same behavior as when I installed it. Then I tried reinstalling where it simply presented the InstallShield Modify/Repair/Remove menu and I selected repair. Nothing happened. Then I tried selecting Modify, then seeing that the only option (called DefaultFeature) was unchecked. Same behaviour as install/uninstall. After seeing that it still failed, I uninstalled again. And after that I deleted C:\Program Files (x86)\League of Legends manually. When I tried installing LoL again it still thought I had it, so I chose repair. This time something actually happened, but it installed the whole game to C:\Windows. Seeing what was going on I clicked cancel and then started it up to try uninstalling it. However, I got an error message about something not being registered and then the minimization to I decided to let it repair completely. Then I uninstalled it and it gave only the minimization. However, when I rebooted another application started up complaining about some library being absent. So I decided to do a system restore. After letting it complete I got a BSOD every time I tried starting up Windows normally or in safe mode. However, system recovery mode works, although the system recovery automatic repair does not fix it. After a bit of searching I found a Microsoft KB article about it (981833) and tried following the workaround instructions. Nothing happened. I am using Windows 7 Home Premium 64-bit and Ubuntu 10.04 LTS 64-bit installed with WUBI.

  Read the article

• Does migrating 2 domain controllers between 2 datacentre requires both virtual machines to be shut down at the same time?

  - by Imagineer

  I was attempting to migrate 2 virtual machines that are domain controllers between 2 datacentres running ESX 3.5 and ESX 4.1. I was advised to shut down both domain controller at the same time during the migration process. This is to avoid USN Rollback and other replication issues. The following are the steps that I was planning to perform: 1. Shutdown both DC. 2. Copy both VMs files across to new datacentre using Veeam FastSCP (connection to both vCentre through IP address instead of hostname) 3. Power them up at new datacentre. 4. Configure Network interface/DNS/DHCP for both DCs in new datacentre I have tried to use Veeam FastSCP rather than VMware Standalone Converter is because its copying rather than converting. Someone also suggested that I use backup and restore app like Veeam backup and replication software. Sounds like a simple job, but after shutting down both DCs, the transfer rate using FastSCP is so slow registering only 1KB/s as oppose to the normal 1MB/s (or more). When that attempt to transfer failed, I tried to cold clone both DCs resulted in the both ESX hosts get disconnected. I have tried troubleshooting by referring to this - VMware KB - Diagnosing an ESX Server that is Disconnected or Not Responding in VirtualCenter It seems that the DNS being down is the caused of all unusual occurrence. The moment I powered up the DCs via VMware console command, the ESX host were able to connect to the vCentre again. How can I avoid such a pitfall again? Am I doing it correctly? Any help would be greatly appreciated! Thank you.

  Read the article

• Outlook 2007 + Exchange 2010 (Save All Attachments)

  - by RobertPitt

  About 3 weeks back our company upgraded our mail system to Exchange 2010, all went smooth, few issues but nothing major. A few days ago we had a call from a colleague where he was unable to save all attachments, From File > Save As > Save All Attachments. When the email has a single attachment it works perfectly normal, and depending on the file type it allows you to save multiple attachments. But there's a lot of file types that will not work, such as zip, pdf, doc etc, Usually we get a location box open up asking where we would like to drop the attachments, but it does nothing, You click Save All Attachments and nothing happens. After hours of research I have come across mixed results, a lot of people on forums have been explaining that they have recently crossed over to Exchange 2010 and there issues started there. But on the other hand Microsoft released a KB (278188) which was depressing if that, but that article was published in 2007, as stated by the time stamp, and Exchange 2010 has only come out recently. Im looking to see if you guys have any clues what could be causing this, anything server side that I can take a look at (AD, Exchange, ...). Any help on this is greatly supported

  Read the article

• C# sends SQL data 4 times less from one box than from another

  - by Bobb

  W2003, .NET 3.5, SQL 2008 I have prod and UAT app servers deployed in 2 different data centres. I have a C# app which reads text file, parse the text and sends the data to the SQL in bulk. SQL server is in US and the app servers are in London (but in different places). All POPs have dedicated network connections. There is no public internet involved. When the app runs on UAT server I can see in Perfmon that the Send byte/sec is x4 higher than from production server. My estimate is that one server outputs at 1 MB/s and the other at 250 KB/s rate. My suspicion immediately is that there is a router on one of the DCs which shapes traffic or does QoS limitation on traffice from London to US. However support and Windows team and networkig team all are saying that there are no differences in neither networking config on the 2 DCs nor NIC config on the 2 app server... How to find out why is the networking bottlneck is 4 times tighter in one place than in the other? What can I do about it?

  Read the article

• FTP Server upload and filesystem questions

  - by Alex

  I'm a photographer who mainly does event photography. A while ago I bought myself a Nikon WT-4 wireless transmitter, a small device which connects via USB to my Nikon D700 DSLR, and then establishes a WiFi connection to an existing WLAN. It can then upload any pictures I take via FTP to an FTP server somewhere in the network. On my laptop I then have a piece of software which will check a given folder on the disk regularly, this software is smart enough to look at the modified file timestamp, if this timestamp is less than 10 seconds ago, it will not attempt to import the folder and skip the file in this iteration of the import scan. The problem I've discovered seems to be inherent to the FTP protocol, as I have the same problem with Windows 7 built in IIS server, as I do with FileZilla FTP server. When the transmitter starts to upload a file, the FTP server will create a small 300-500 KB file with the correct filename on the disk, but then do nothing with the file until it has completely received the file via FTP. So it seems to create this small dummy file, and then buffer the remainder of the FTP upload until it's finished, and then dump the rest of the file into the dummy file making it the correct size. Problem is, these uploads take about 15-30 seconds depending on reception, but since the folder watch tool will already try to import any file older than 10 seconds, it will always try to import the small dummy files which obviously fails as they're not copmlete yet. Is there any way to 'disable' this behaviour? Ideally I would like my file only to show up once it's been completely uploaded. Or perhaps someone knows another FTP server application (it has to run on win7) which does not show this behaviour?

  Read the article

• SSH Connection Error : No route to host

  - by dewbot

  There are three machines in this scenario: Desktop A : [email protected] Laptop A : [email protected] Machine B : [email protected] All the machines have Ubuntu 11.04 (Desktop A is a 64bit one) and have both openssh-server and openssh-client. Now when I try to connect Desktop A to Laptop A or vice-versa by ssh [email protected] I get an error as port 22: No route to host in both the cases. I own both the machines, now if I try same commands from my friend's machine, i.e. via Desktop B, I can access both my Laptop and Desktop. But if I try to access Desktop B from my Laptop or by Desktop I get port 22: Connection timed out I even tried changing ssh port no. in ssh_config file but no success. Note: that 'Laptop A' uses WiFi connection while 'Machine A' uses Ethernet Connection and 'Machine B' is on an entirely different network. Laptop A && Desktop A - Router/Nano_Rcvr provided to me by ISP. So to one Router two Machines are connected and can be accessed at the same time. here is my ifconfig output for both the machines :- Laptop wlan0 Link encap:Ethernet HWaddr X:X:X:X:00:bc inet addr:1.23.73.111 Bcast:1.23.95.255 Mask:255.255.224.0 inet6 addr: fe80::219:e3ff:fe04:bc/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:108409 errors:0 dropped:0 overruns:0 frame:0 TX packets:82523 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:44974080 (44.9 MB) TX bytes:22973031 (22.9 MB) Desktop eth0 Link encap:Ethernet HWaddr X:X:X:X:c5:78 inet addr:1.23.68.209 Bcast:1.23.95.255 Mask:255.255.224.0 inet6 addr: fe80::227:eff:fe04:c578/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:10380 errors:0 dropped:0 overruns:0 frame:0 TX packets:4509 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1790366 (1.7 MB) TX bytes:852877 (852.8 KB) Interrupt:43 Base address:0x2000

  Read the article

• Chef bash resource not executing as specified user

  - by Arthur Maltson

  I'm writing a Chef cookbook to install Hubot. In the recipe, I do the following: bash "install hubot" do user hubot_user group hubot_group cwd install_dir code <<-EOH wget https://github.com/downloads/github/hubot/hubot-#{node['hubot']['version']}.tar.gz && \ tar xzvf hubot-#{node['hubot']['version']}.tar.gz && \ cd hubot && \ npm install EOH end However, when I try to run chef-client on the server installing the cookbook, I'm getting a permission denied writing to the directory of the user that runs chef-client, not the hubot user. For some reason, npm is trying to run under the wrong user, not the user specified in the bash resource. I am able to run sudo su - hubot -c "npm install /usr/local/hubot/hubot" manually, and this gets the result I want (installs hubot as the hubot user). However, it seems chef-client isn't executing the command as the hubot user. Below you'll find the chef-client execution. Thank you in advance. Saving to: `hubot-2.1.0.tar.gz' 0K ...... 100% 563K=0.01s 2012-01-23 12:32:55 (563 KB/s) - `hubot-2.1.0.tar.gz' saved [7115/7115] npm ERR! Could not create /home/<user-chef-client-uses>/.npm/log/1.2.0/package.tgz npm ERR! Failed creating the tarball. npm ERR! couldn't pack /tmp/npm-1327339976597/1327339976597-0.13104878342710435/contents/package to /home/<user-chef-client-uses>/.npm/log/1.2.0/package.tgz npm ERR! error installing [email protected] Error: EACCES, permission denied '/home/<user-chef-client-uses>/.npm/log' ... npm not ok ---- End output of "bash" "/tmp/chef-script20120123-25024-u9nps2-0" ---- Ran "bash" "/tmp/chef-script20120123-25024-u9nps2-0" returned 1

  Read the article

• realtek lan driver problem - win 7

  - by tango _123

  Hi, my new notebook (ACER TM 8371) with Win 7(x32) professional as OS, has strage behaviour with respect to LAN. when I plug or unplug my charger cable, or my notebook goes in stad-by, or just a do nothing, the netwrok connection is lost. All the energy savings functionbality have been in-activated. if i check the network adapter information, it says "a network cabel is unplugged or corrupted", but it is not true.....the cable is in and it is not corrupted (i tried several which works on other machines). if a tried to di-habilitate and hence re-habilitate, it allows di-habilitation and not to further re-habilitate (it says "no driver for the network card" are available). in some cases, also, the driver disappears (i cannot see it anylonger). if i restart the notebook, everything comes back to normality, but.....today in 3 hours i had to restart 6 times!!! can anyone help me? win 7 says the driver is the last one, so no need to update it. here are some techinical information aboiut network card and driver: Name [00000015] Realtek PCIe GBE Family Controller Adapter type Ethernet 802.3 Product type Realtek PCIe GBE Family Controller Installated YES ID device PNP PCI\VEN_10EC&DEV_8168&SUBSYS_02831025&REV_02\4&266E4C4F&0&00E2 last reset 20/11/2009 11:27 Index 15 Service name RTL8167 I/O Port 0x0000FF00-0x0000FFFF Memory address 0xE2500000-0xE2500FFF Memory address 0xE1400000-0xE140FFFF IRQ Channel IRQ 18 Driver c:\windows\system32\drivers\rt86win7.sys (7.3.522.2009, 164,00 KB (167.936 Byte), 28/08/2009 22:12)

  Read the article

• Exchange 2003 Internet Mail Size Limits

  - by scampbell

  I have unsuccessfully tried to increase per user incoming mail size settings by editing their user account settings on our Exchange server, but large incoming mail from external domains is still blocked using the default global settings. After reading here: http://support.microsoft.com/default.aspx?scid=kb;en-us;322679 I see that All Internet e-mail messages use the global setting for limits on sending and on receiving. The message categorizer evaluates the sender's sending limit and the recipient's receiving limit. In example 2 earlier, a user with a user mailbox limit of 3 MB could receive messages from another user with a 3-MB sending limit. Because Internet users use the global setting, they can send only a 2-MB message. Which to me is madness! Surely if I want to allow a user to receive mail up to a certain size then I should be able to set it as such? Is there a specific way of getting round this? Would setting the global defaults high and setting a lower, say 10MB, limit on the SMTP connector do the trick? Thanks.

  Read the article

• Second CPU missing of Dual Core

  - by Zardoz

  My Lenovo T61 has a dual core CPU. I just noticed that under Ubuntu 10.10 only one CPU is recognized. I know that once both CPUs worked. Not sure since when the second CPU is missing. Maybe since the last kernel update. Currently I am using linux-image-2.6.35-23-generic (for x86_64). What can I do to enable the second CPU again? Here the ouput of /proc/cpuinfo processor : 0 vendor_id : GenuineIntel cpu family : 6 model : 23 model name : Intel(R) Core(TM)2 Duo CPU T8100 @ 2.10GHz stepping : 6 cpu MHz : 800.000 cache size : 3072 KB physical id : 0 siblings : 1 core id : 0 cpu cores : 1 apicid : 0 initial apicid : 0 fpu : yes fpu_exception : yes cpuid level : 10 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe syscall nx lm constant_tsc arch_perfmon pebs bts rep_good aperfmperf pni dtes64 monitor ds_cpl vmx est tm2 ssse3 cx16 xtpr pdcm sse4_1 lahf_lm ida dts tpr_shadow vnmi flexpriority bogomips : 4189.99 clflush size : 64 cache_alignment : 64 address sizes : 36 bits physical, 48 bits virtual power management: Any help is welcome. I really need that CPU power for my work here.

  Read the article

• Why is piping dd through gzip so much faster than a direct copy?

  - by Foo Bar

  I wanted to backup a path from a computer in my network to another computer in the same network over a 100MBit/s line. For this I did dd if=/local/path of=/remote/path/in/local/network/backup.img which gave me a very low network transfer speed of something about 50 to 100 kB/s, which would have taken forever. So I stopped it and decided to try gzipping it on the fly to make it much smaller so that the amount to transfer is less. So I did dd if=/local/folder | gzip > /remote/path/in/local/network/backup.img.gz But now I get something like 1 MB/s network transfer speed, so a factor of 10 to 20 faster. After noticing this, I tested this on several paths and files and it was always the same. Why does piping dd through gzip also increase the transfer rates by a large factor instead of only reducing the bytelength of the stream by a large factor? I'd expected even a small decrease in transfer rates instead, due to the higher CPU consumption while compressing, but now I get a double plus. Not that I'm not happy, but just wondering. ;)

  Read the article

• maximum size filesystem on my test .... approach?

  - by jocco

  Hello all I'm new at the site, and I have a question. I got this question at a test and really like to know the correct approach to solving this problem? Here is the question. In an indexed filesystem the first indexblock (inode) has 12 direct pointers and 1 pointer to an indirect indexblock. The filesystem is implemented on a disk with a diskblock-size of 1024 bytes. All pointers are 32 bit. Question: what is the maximum filesize (Kilobytes) of this filesystem? If it's possible not an just an answer but an explanation. edit: It was a multiple choice btw with 4 answers a. 13 K b. 268 K c. 524 K d. 1036 K As for my approach I only got as far as to know that 1 pointer is 32 bit Also I found something else here on the site which seems very usefull. http://stackoverflow.com/questions/2755006/understanding-the-concept-of-inodes Ok i got this far There are 12 blocks and each block is 1024 bytes. 1024 * 12 = 12288 bytes or 12 KB directly accessible. Please correct me if I'm wrong. Each pointer is 32 Bit = 4Byte And to be honest at this point I'm starting to get confused especially since my answer is way over any of my multiple choice answers.

  Read the article

• Many clients on a wireless AP for UDP broadcast packets

  - by distorteddisco

  I asked this question on StackOverflow and was directed over here, so I'd appreciate any advice. I'm deploying a smartphone application as part of a live music performance that depends on receiving UDP broadcast packets from a wireless access point. I'm guessing that between 20 and 50 clients will be connected at any one time. I'm aware that a maximum of 20 clients per access point is advised, but as the UDP broadcast packets are ground through the LAN, how would I be able to link multiple APs together? I'm looking for recommendations on a suitable AP for this. The actual data transmission rates are very low - only a few kB/s - as I'm just sending small messages to the smartphone apps, and there will be no WAN internet connection. I tried it with a few connected peers on an adhoc wireless connection without any problems, but ran into dropped packet issues on an old WRT54G running ddwrt, though it's in pretty rough shape. What's the best way to do this? I suppose I could limit concurrent wireless connections to 20 clients... but more would be nice. EDIT: I should also say that it's purely one-way communication; the smartphone application is only receiving broadcast packets, not sending anything.

  Read the article

• Is my "Generic" USB Flash Drive broken?

  - by Jesse J.

  So here is the situation. I find myself technological knowledgeable about many things ( I love to code, whether it's websites, C#, C++ or so on). However: My 2 toddlers (my wife actually) bought me a "Generic" 128 GB USB Storage Device (Usb Flash Drive) for Father's Day. I thought awesome at first..... WRONG! Nothing but problems with it. 3-4mb/s MAX transfer speed. I can bear with it. BUT! When I went to reformat my computer I transferred my save files from my games over to the stick and then the USB Stick managed to become corrupted. Not just a simple format would work either. It's screwed. I tried to use (Manually changed usb drive letter troubleshooting it to X) "chmod X: /X /F /R" with administrator rights, I did this after a long session to make it work with no errors (had to delete the log) and I finally recovered the files, however when I go to use it (transfer to or from) it transfers a couple kb to the stick or from it and then freezes, It says (Windows 7): Name: From: Folder (X:\File\Location) To: Folder C:\Users\Username\Desktop) Items Remaining: 0 (0 bytes) Speed: 0 bytes/second It does this forever... and ever... and ever... It transfered 3 files atleast, and then stopped. This is a new USB Stick bought from a "High" reputation company on eBay. Is the USB Stick screwed?

  Read the article

• Screen randomly goes blue/black/white

  - by FubsyGamer

  Problem Randomly, while using my computer, the monitor goes dark grey/almost black, or it goes white with faint grey vertical lines, or it goes blue with black vertical lines. It's as if the computer powers off. People tell me I sign out of Skype, Spotify stops playing when it happens, etc. When I look at the tower, it doesn't seem like it's off at all. Nothing changes, fans are spinning, lights are on, etc. If you were only looking at the tower, you'd never know there was a problem The only way I can get it to come back up is to push and hold the power button and turn it off, then back on This never happens while I'm playing video games. I've done 5-6 hour sessions of League of Legends, and it doesn't do anything When I'm just browsing the web, reading email, checking Reddit, etc, it happens all the time. It can happen multiple times in a session, it usually takes only about 5 minutes from the time I start browsing to when the computer crashes This started happening after I moved to a new apartment (this has to be relevant somehow, it was not happening where I lived before) There is nothing in the crash logs or event logs System Specs i5 2500k CPU AMD Radeon 6800 GPU Gigabyte z68a-d3h-b3 motherboard WD VelociRaptor 1 TB HDD Screenshots Device manager About screen Things I have tried I was getting a WMI Error in my event logs, but I fixed it using Microsoft's fix, KB 2545227 I was using Windows 8. I wiped the HDD and downgraded to Windows 7 64 bit I took out the video card and used a can of air to totally clean out the video card, all fans, and the inside of the computer in general. I made sure all of the video card pins were fine, then reconnected it I tried to update my motherboard BIOS, but anything I downloaded from Gigabyte was only for 32 bit machines, not 64. I don't even know how to tell what my motherboard BIOS is at right now I am using a power strip, and anything else connected to it works just fine If I re-seat the monitor cable while this is happening, nothing changes Please, help me. I've been battling this for several weeks now, and it's so frustrating it makes me not even want to use the computer.

  Read the article

• How do I get to the bottom of network latency and bandwidth issues

  - by three_cups_of_java

  I recently moved two blocks south. That move moved me from Comcast to Broadstripe (high-speed internet cable providers). Comcast was pretty good. Broadstripe sucks. I called them on the phone, and they basically brushed me off (politely). I want to come to them with some numbers, so I can say more than just "it's really slow". I still have access to my old Comcast service, so I can run the tests using both providers. Here's what I'm seeing with my new Broadstripe service: 1) When I browse to most sites, there is a long delay (5-10 seconds) before the page starts loading in my browser 2) The speed test tell me I have 12 megs down (bullshit) 3) I have a server at my office. I just downloaded some files (using scp on the command line). It said I'm getting 3.5 KB/s I'm an experienced programmer and spend most of my days on the command line and in vim. Networking, however is not a strong point. I've played around with traceroute, but I'm not sure if that's the right tool to use. I have access to servers all over the country (I would just use Amazon EC2 to set up a test server), and I prefer to use Ubuntu for my testing. How can I come up with some hard numbers to show Broadstripe how crappy their service is?

  Read the article

• What is the best hosting option for Flash web-widget?

  - by par

  Our Flash web-widget has got highly popular. It is downloaded around 100,000 times per day. And that is the problem. Our server bandwidth is too narrow to deliver the widget to the clients fast. The widget is loaded very slow. Probably 20 times slower than before (at peak times). Probably I have choosen not the right hoster for my task - delivering 1 MB Flash widget to 100,000 users per day. What is the best hosting solution in my case? I'm not good at server administration so forgive me if I sound naive. The details are the following. Our hoster options: -Dedicated server, Ubuntu -10 Mbit Connection -monthly bandwidth limit: 2000 GB Widget size is 1 MB. The widget consists of the main SWF and a number of loaded SWF and data files. This is a part of Apache Status report taken right now ---- Server uptime: 1 hour 2 minutes 38 seconds Total accesses: 74865 - Total Traffic: 5.8 GB CPU Usage: u28 s7.78 cu0 cs0 - .952% CPU load 19.9 requests/sec - 1.6 MB/second - 81.1 kB/request 200 requests currently being processed, 0 idle workers WWWWWWWWWWWWWWWWWWWWWWWWCWWWWWWWWWWWWWWWWWWWWWWWWWWCWWWWWWWCWWWW WWWWWCWWWWWWWWWWWWWWCWWWWWWWWWWWWCWWWWWWWWCWWCWWWWWWWWWWWWWWWWWW WWWWWWWWWWWWWWWWCWWWWWWWWWWWWWWWWWWWWWWWWWWWCWCWWWWWWWWWWWWWWWCW WWWWWWWW........................................................ ----

  Read the article

• Active Directory server down, recovering without reinstalling

  - by whatever

  My Windows 2003 server suddenly ceased to function as a DC (this server is the only DC of the domain). All AD related services are down. The only way I can login to the AD is physically to the machine. Everytime I access an AD-related service (e.g. "AD users and computers") I get the below error: Naming information cannot be located because: The specified directory service attribute or value does not exist. Contact your system administrator to verify that your domain is properly configured and is currently online. I found the below system event which matches the time when the issue started, this re-occurs everytime I reboot the server. NTDS General | Global Catalog | Active Directory was unable to establish a connection with the global catalog. Additional Data Error value: 1355 The specified domain either does not exist or could not be contacted. Internal ID: 3200d33 I started the troubleshooting with DNS. Netdiag throws the below error although I think this is simply a consequence of not being able to access the Global Catalog. The procedure entry point DnsGetPrimaryDomainName_UTF8 could not be located in the dynamic link library DNSAPI.dll. Anyway DNS seems OK because I can ping the DC FQDN from the DC itself. I found the below solution which is supposed to help by doing some cleanup of the metadata: http://support.microsoft.com/kb/216498 If I follow procedure 1 here is what I get at step 9: no current site Domain - DC=<mydomain>,DC=<com> no current server no current naming context I can continue the procedure until step 14. I haven't tested step 15 as my understanding is that I will have to reinstall the whole AD again. Is there any way I can recover my AD from there without having to reinstall the whole thing? Update: Yes, the server was powered off/on because reboot would take forever (not because I thought power cycling the unit would fix it more than a reboot).

  Read the article

• How do I back up Hyper-V VMs with Windows Server backup on Windows Server 2008 R2?

  - by Chris

  I've searched this site and google, and I CAN find information about how to back up Hyper-V virtual machines by using Windows Server Backup from the Hyper-V host in Windows Server 2008. You have to set up a registry key to enable the Hyper-V VSS writer, and then you can take online backups of your VMs. However, all the information I have found is about a year old, and none of it has been updated for Windows Server 2008 R2. I tried to run the "FixIt" .msi found here: http://support.microsoft.com/kb/958662 ... but it said that it was not applicable to my operating system. So I am thinking either Windows Server 2008 R2 already has its VSS service for Hyper-V enabled, or it still needs to be enabled but the FixIt package doesn't feel comfortable operating on an OS that wasn't RTM at the time. I went ahead and scheduled a windows server backup for 9pm tomorrow. It said it would take 86 GB, which means it MUST be counting those VMs. But will this backup fail? Can anyone confirm whether you have to apply the same registry changes for R2?

  Read the article

• Reading log files from web application

  - by Egorinsk

  Hi! I want to write a small PHP application for monitoring logs on a Debian server, including syslog logs and Apache/PHP messages. The problem here is that Apache user (www-data) has no access to /var/log directory. What would be the best way to grant an access to logs for PHP application? Let's assume that log files can be really large, like hundreds of megabytes. I have some ideas: Write a shell script that would be run via sudo and tail last 512 Kb of log into a separate file that can be read by application - that's ineffective, because of forking a new process and having to read data twice Add www-data to adm group (that can read logs) - that's insecure Start a PHP process via cron every minute to read logs — that's not very good, because it doesn't allow real-time monitoring. Also, this script will be started even when I don't read logs, and consume CPU time (server is in the cloud, and I'll have to pay for it) Create a hardlink for all log files with lowered permissions - I guess, that won't work because logrotate could recreate log files and they'll change inode number. Start a separate nginx/Apache server under privileged user that may read logs. Maybe anyone got a better solution?

  Read the article

• Determining how all memory is used in Windows Server 2008

  - by Mojah

  Hi, I have a Windows Server 2008 system, which has 12GB of RAM. If I list all processes in the Task Manager, and SUM() the memory of each process (Working Set, Memory (Private Working Set), Commit Size, ...), I never reach more than 4-5GB that should be "in use". However, task manager reports this server has 11GB in use via the "Performance" tab. I'm failing in determining where all that used RAM is going. It doesn't seem to be system cache, but I can not be sure. It might be a memory leak in one of the appliances, but I'm struggling to find out which one. The server's memory keeps filing up, and eventually forces us to reboot the device to clear it. I've been reading up on how RAM assignments work on Windows Server: RAM, Virtual Memory, Pagefile and all that stuff: http://support.microsoft.com/kb/2267427 What's the best way to measure? http://www.zdnet.com/blog/bott/windows-7-memory-usage-whats-the-best-way-to-measure/1786 Configure the file system cache in Windows: http://smallvoid.com/article/winnt-system-cache.html But I fear I'm stuck without ideas at the moment.

  Read the article

• Profile not loaded correctly (Cannot access registry)

  - by xaav

  Every so often, I log on and get the Following Message: User profile was not loaded correctly. You have been logged on with a temporary profile. Changes you make to this profile will be lost when you log off. Please see the event log for details or contact your administrator This almost always happens when somebody else has been on the computer for a while, and then I log on. This never used to happen, but now it happens pretty often. My profile is not permanently corrupted, all I have to do is restart my computer, but this annoys me, and I would like to fix it. I was curios about the reason of this cause, so I looked into the Event Log, and found the root of the problem was the ntuser.dat file in the profile that I was logging on to was locked at logon time. This resulted in the current users registry not being loaded, resulting in failure to load the profile. I just found a microsoft article that mentions this exact issue: http://support.microsoft.com/kb/960464/ The problem is that I do not want to delete this profile; and this issue does not come up every time that I log on, only when somebody else has been on a long time before me. What could be locking this file? Is there any way to get a process list without logging on so that I can identify which process has the file locked? Any other suggestions?

  Read the article

• Hungry hungry BIOS: why do I have less than 4 GiB of memory?

  - by Rhymoid

  I thought I had 4 GiB of memory, but just to be sure, let's ask the BIOS about that: ?: sudo dmidecode --type 20 # dmidecode 2.12 SMBIOS 2.6 present. Handle 0x000B, DMI type 20, 19 bytes Memory Device Mapped Address Starting Address: 0x00000000000 Ending Address: 0x0007FFFFFFF Range Size: 2 GB Physical Device Handle: 0x000A Memory Array Mapped Address Handle: 0x000E Partition Row Position: Unknown Interleave Position: Unknown Interleaved Data Depth: Unknown Handle 0x000D, DMI type 20, 19 bytes Memory Device Mapped Address Starting Address: 0x00080000000 Ending Address: 0x000FFFFFFFF Range Size: 2 GB Physical Device Handle: 0x000C Memory Array Mapped Address Handle: 0x000E Partition Row Position: Unknown Interleave Position: Unknown Interleaved Data Depth: Unknown Alright, 4 GiB it is. But I can't use all of it: ?: cat /proc/meminfo | head -n 1 MemTotal: 3913452 kB Somehow, somewhere, I lost 274 MiB. Where did 6% of my memory go? Now I know the address ranges in DMI are incorrect, because the ACPI memory map reports usable ranges well beyond the ending address of the second memory module: ?: dmesg | grep -E "BIOS-e820: .* usable" [ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009e7ff] usable [ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x00000000dee7bfff] usable [ 0.000000] BIOS-e820: [mem 0x0000000100000000-0x0000000117ffffff] usable I get pretty much the same info from /proc/iomem (except for the 4 kiB hole 0x000-0xFFF), which also shows that the kernel only accounts for less than 8 MiB. I guess 0x00000000-0x7FFFFFFF is indeed mapped to the first memory module, and 0x80000000-0xDFFFFFFF to part of the second memory module (a bunch of ACPI NVS things live between 0xDEE7C000 and 0xDEF30FFF, and the remaining 16-something MiB of that range are just 'reserved'). I guess the highest 0x18000000 bytes of the second memory module are mapped above the 4 GiB mark. But even then, there are two problems: 128 MiB (0x08000000 bytes, living somewhere between 0xE0000000 and 0xFFFFFFFF) are still completely unaccounted for. To note, my graphics card is on PCI-Express and (allegedly) has 1 GiB dedicated memory, so that shouldn't be the culprit. Did the BIOS screw up in moving the memory, leaving it partially shadowed by MMIO? Even with this mediocre explanation, I only 'found' 128 MiB. But /proc/meminfo is reporting a much larger deficit; where's the other 146 MiB? How does Linux count MemTotal?

  Read the article

• Determining how all memory is used in Windows Server 2008

  - by Mojah

  I have a Windows Server 2008 system, which has 12GB of RAM. If I list all processes in the Task Manager, and SUM() the memory of each process (Working Set, Memory (Private Working Set), Commit Size, ...), I never reach more than 4-5GB that should be "in use". However, task manager reports this server has 11GB in use via the "Performance" tab. I'm failing in determining where all that used RAM is going. It doesn't seem to be system cache, but I can not be sure. It might be a memory leak in one of the appliances, but I'm struggling to find out which one. The server's memory keeps filing up, and eventually forces us to reboot the device to clear it. I've been reading up on how RAM assignments work on Windows Server: RAM, Virtual Memory, Pagefile and all that stuff: http://support.microsoft.com/kb/2267427 What's the best way to measure? http://www.zdnet.com/blog/bott/windows-7-memory-usage-whats-the-best-way-to-measure/1786 Configure the file system cache in Windows: http://smallvoid.com/article/winnt-system-cache.html But I fear I'm stuck without ideas at the moment.

  Read the article

< Previous Page | 55 56 57 58 59 60 61 62 63 64 65 66  | Next Page >