Search Results

Search found 54080 results on 2164 pages for 'wireless access point'.

Page 59/2164 | < Previous Page | 55 56 57 58 59 60 61 62 63 64 65 66  | Next Page >

• Need help with chronic slow wifi connections

  - by mgeorge

  I have had chronic slow wifi connections on several networks for a while now, I think since my update to 12.04 when it came out. I have tried many of the tips and tricks already available out there in the forums with no luck (wicd, etc..). I want to see if any of you experts out there might be able to help me, and thanks in advance!! I use ubuntu 12.04 on a lenovo ideapad y650, and most networks I connect to lose the connection frequently or do not give appropriate bandwidth when I am connected. Here are some results of the usual go-to system checks: cat /etc/lsb-release; uname -a: DISTRIB_ID=Ubuntu DISTRIB_RELEASE=12.04 DISTRIB_CODENAME=precise DISTRIB_DESCRIPTION="Ubuntu 12.04.2 LTS" Linux mgeorge-lenovo 3.2.0-48-generic-pae #74-Ubuntu SMP Thu Jun 6 20:05:01 UTC 2013 i686 i686 i386 GNU/Linux lspci -nnk | grep -iA2 net: 04:00.0 Network controller [0280]: Intel Corporation PRO/Wireless 5100 AGN [Shiloh] Network Connection [8086:4237] Subsystem: Intel Corporation WiFi Link 5100 AGN [8086:1211] Kernel driver in use: iwlwifi -- 08:00.0 Ethernet controller [0200]: Broadcom Corporation NetLink BCM5784M Gigabit Ethernet PCIe [14e4:1698] (rev 10) Subsystem: Lenovo Device [17aa:3878] Kernel driver in use: tg3 lsusb: Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 002: ID 090c:7371 Silicon Motion, Inc. - Taiwan (formerly Feiya Technology Corp.) iwconfig: lo no wireless extensions. wlan0 IEEE 802.11abgn ESSID:"Dyno" Mode:Managed Frequency:2.412 GHz Access Point: CC:5D:4E:46:0A:93 Bit Rate=150 Mb/s Tx-Power=15 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=70/70 Signal level=-40 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:948 Invalid misc:728 Missed beacon:0 eth0 no wireless extensions. rfkill list all: 0: ideapad_wlan: Wireless LAN Soft blocked: no Hard blocked: no 1: ideapad_bluetooth: Bluetooth Soft blocked: yes Hard blocked: no 2: phy0: Wireless LAN Soft blocked: no Hard blocked: no lsmod: Module Size Used by uvcvideo 67203 0 videodev 86588 1 uvcvideo nouveau 712674 3 ttm 65344 1 nouveau drm_kms_helper 45466 1 nouveau drm 197641 5 nouveau,ttm,drm_kms_helper i2c_algo_bit 13199 1 nouveau mxm_wmi 12893 1 nouveau wmi 18744 1 mxm_wmi joydev 17393 0 arc4 12473 2 snd_hda_codec_realtek 174313 1 snd_hda_codec_hdmi 31775 1 snd_hda_intel 32719 3 snd_hda_codec 109562 3 snd_hda_codec_realtek,snd_hda_codec_hdmi,snd_hda_intel snd_hwdep 13276 1 snd_hda_codec snd_pcm 80916 3 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec snd_seq_midi 13132 0 snd_rawmidi 25424 1 snd_seq_midi snd_seq_midi_event 14475 1 snd_seq_midi psmouse 86520 0 snd_seq 51592 2 snd_seq_midi,snd_seq_midi_event serio_raw 13027 0 snd_timer 28931 2 snd_pcm,snd_seq snd_seq_device 14172 3 snd_seq_midi,snd_rawmidi,snd_seq iwlwifi 366509 0 mac80211 436493 1 iwlwifi snd 62218 16 snd_hda_codec_realtek,snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,sn d_rawmidi,snd_seq,snd_timer,snd_seq_device ideapad_laptop 17890 0 sparse_keymap 13658 1 ideapad_laptop cfg80211 178877 2 iwlwifi,mac80211 ir_lirc_codec 12739 0 lirc_dev 18700 1 ir_lirc_codec soundcore 14635 1 snd snd_page_alloc 14108 2 snd_hda_intel,snd_pcm ir_mce_kbd_decoder 12681 0 ir_sony_decoder 12462 0 ir_jvc_decoder 12459 0 ir_rc6_decoder 12459 0 ir_rc5_decoder 12459 0 rc_rc6_mce 12454 0 ir_nec_decoder 12459 0 video 19115 1 nouveau ene_ir 18019 0 rc_core 21263 10 ir_lirc_codec,ir_mce_kbd_decoder,ir_sony_decoder,ir_jvc_decoder,ir_rc6_decoder,ir_rc5_decoder,rc_rc6_mce,ir_nec_decoder,ene_ir bnep 17830 2 rfcomm 38139 0 parport_pc 32114 0 bluetooth 158479 10 bnep,rfcomm ppdev 12849 0 binfmt_misc 17292 1 mac_hid 13077 0 lp 17455 0 parport 40930 3 parport_pc,ppdev,lp tg3 141414 0 nm-tool: NetworkManager Tool State: connected (global) - Device: eth0 ----------------------------------------------------------------- Type: Wired Driver: tg3 State: unavailable Default: no HW Address: 00:23:5A:CC:85:BD Capabilities: Carrier Detect: yes Wired Properties Carrier: off - Device: wlan0 [Dyno] -------------------------------------------------------- Type: 802.11 WiFi Driver: iwlwifi State: connected Default: yes HW Address: 00:22:FA:D0:94:CA Capabilities: Speed: 150 Mb/s Wireless Properties WEP Encryption: yes WPA Encryption: yes WPA2 Encryption: yes Wireless Access Points (* = current AP) *Dyno: Infra, CC:5D:4E:46:0A:93, Freq 2412 MHz, Rate 54 Mb/s, Strength 81 WPA2 IPv4 Settings: Address: 10.0.0.43 Prefix: 24 (255.255.255.0) Gateway: 10.0.0.1 DNS: 10.0.0.1

  Read the article

• Upgraded to 12.04 now wifi doesn't work

  - by Benito Kestelman

  My laptop's wifi stopped working when I upgraded to Ubuntu 12.04 (wired works). I just reinstalled 12.04 over my old 12.04 on which wifi didn't work either in an attempt to restore any settings I may have accidentally changed, but it still doesn't work. I also used a wired connection to install updates in case this bug has been fixed, but it has not. Here is the result of sudo lshw -class network: *-network description: Wireless interface product: Centrino Wireless-N + WiMAX 6150 vendor: Intel Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 67 serial: 40:25:c2:5f:5b:f4 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlwifi driverversion=3.2.0-29-generic-pae firmware=41.28.5.1 build 33926 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:51 memory:de800000-de801fff *-network description: Ethernet interface product: AR8151 v2.0 Gigabit Ethernet vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:04:00.0 logical name: eth0 version: c0 serial: 14:da:e9:c0:da:78 capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vpd bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.0-NAPI firmware=N/A latency=0 link=no multicast=yes port=twisted pair resources: irq:54 memory:dd400000-dd43ffff ioport:a000(size=128) Here is rfkill list all: 0: phy0: Wireless LAN Soft blocked: no Hard blocked: no 1: asus-wlan: Wireless LAN Soft blocked: no Hard blocked: no 2: asus-wimax: WiMAX Soft blocked: no Hard blocked: no lsusb: Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 003: ID 8087:07d6 Intel Corp. Bus 001 Device 004: ID 13d3:5710 IMC Networks Bus 002 Device 003: ID 045e:0745 Microsoft Corp. Nano Transceiver v1.0 for Bluetooth Bus 003 Device 003: ID 0781:5530 SanDisk Corp. Cruzer lspci: 00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09) 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) 00:16.0 Communication controller: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 (rev 04) 00:1a.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 (rev 05) 00:1b.0 Audio device: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller (rev 05) 00:1c.0 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 (rev b5) 00:1c.1 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 2 (rev b5) 00:1c.3 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 4 (rev b5) 00:1c.5 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 6 (rev b5) 00:1d.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 (rev 05) 00:1f.0 ISA bridge: Intel Corporation HM65 Express Chipset Family LPC Controller (rev 05) 00:1f.2 SATA controller: Intel Corporation 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller (rev 05) 00:1f.3 SMBus: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller (rev 05) 02:00.0 Network controller: Intel Corporation Centrino Wireless-N + WiMAX 6150 (rev 67) 03:00.0 USB controller: ASMedia Technology Inc. ASM1042 SuperSpeed USB Host Controller 04:00.0 Ethernet controller: Atheros Communications Inc. AR8151 v2.0 Gigabit Ethernet (rev c0)

  Read the article

• How can set up a file sharing server to allow remote access over a WAN?

  - by pst007x

  I want to set up a server to allow remote access over a WAN. The purpose is to allow people to remote connect and download specific files from a specified folder hosted on the server. Is there software available to achieve this, preferably with an interface so I can easily add and remove users, plus monitor who is connected at any time? I have looked around and only found terminal references, and not very clear how to set up. I have a service running on my Win server, but I am hoping to move from that to Ubuntu for my file sharing. I do not want people who access the server to have any local accounts or any access to any folder/files apart from authorised folders/files. Thanks

  Read the article

• sony vaio WLAN problem using 12.04

  - by Fredrik

  I'm unable to get my WLAN to work for my Sony Vaio model VPCF23C5E No problem connecting from windows, smartphones etc. $ sudo lshw -C network; lsb_release -a; uname -a; sudo rfkill list; dmesg | grep -i firm *-network description: Wireless interface product: AR9485 Wireless Network Adapter vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 01 serial: 64:27:37:92:99:0f width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list rom ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.2.0-29-generic firmware=N/A latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:16 memory:f7000000-f707ffff memory:f7080000-f708ffff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:05:00.0 logical name: eth0 version: 06 serial: f0:bf:97:dd:b2:bd size: 1Gbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8168e-1.fw ip=192.168.1.4 latency=0 link=yes multicast=yes port=MII speed=1Gbit/s resources: irq:50 ioport:9000(size=256) memory:e2104000-e2104fff memory:e2100000-e2103fff LSB Version: core-2.0-amd64:core-2.0-noarch:core-3.0-amd64:core-3.0-noarch:core-3.1-amd64:core-3.1-noarch:core-3.2-amd64:core-3.2-noarch:core-4.0-amd64:core-4.0-noarch Distributor ID: Ubuntu Description: Ubuntu 12.04.1 LTS Release: 12.04 Codename: precise Linux siriedit 3.2.0-29-generic #46-Ubuntu SMP Fri Jul 27 17:03:23 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux 1: phy0: Wireless LAN Soft blocked: no Hard blocked: no 2: hci0: Bluetooth Soft blocked: no Hard blocked: no [ 1.287449] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored [ 18.273582] [Firmware Bug]: ACPI(NGFX) defines _DOD but not _DOS Seen some proposed solution e.g. Wireless network cannot be enabled for Sony VAIO E series but answers there don't solve my problem... I'm out of ideas :-( What else can I check? update $ ifconfig -a eth0 Link encap:Ethernet HWaddr f0:bf:97:dd:b2:bd inet addr:192.168.1.4 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::f2bf:97ff:fedd:b2bd/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5072 errors:0 dropped:0 overruns:0 frame:0 TX packets:4444 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4568435 (4.5 MB) TX bytes:610624 (610.6 KB) Interrupt:50 Base address:0xc000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:1498 errors:0 dropped:0 overruns:0 frame:0 TX packets:1498 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:114156 (114.1 KB) TX bytes:114156 (114.1 KB) wlan0 Link encap:Ethernet HWaddr 64:27:37:92:99:0f inet addr:192.168.1.5 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::6627:37ff:fe92:990f/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1277 errors:0 dropped:0 overruns:0 frame:0 TX packets:472 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:483155 (483.1 KB) TX bytes:61031 (61.0 KB)

  Read the article

• Drivers for Atheros AR928X?

  - by Pato7

  I am new in Ubuntu and I had a big trouble with wifi. My ubuntu 12.10 doesn't detect my wifi card and I can't toggle the "activate wireless" option on the tasks bar (it is grey). I searched for drivers to make it work, but nothing worked for me. Can anyone give me a hand? Many thanks in advanced! lspci output 00:00.0 Host bridge: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub (rev 07) 00:01.0 PCI bridge: Intel Corporation Mobile 4 Series Chipset PCI Express Graphics Port (rev 07) 00:1a.0 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 (rev 03) 00:1a.1 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 (rev 03) 00:1a.2 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 (rev 03) 00:1a.7 USB controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 (rev 03) 00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio Controller (rev 03) 00:1c.0 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 (rev 03) 00:1c.1 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 2 (rev 03) 00:1c.2 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 3 (rev 03) 00:1d.0 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 (rev 03) 00:1d.1 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 (rev 03) 00:1d.2 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 (rev 03) 00:1d.7 USB controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 (rev 03) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 93) 00:1f.0 ISA bridge: Intel Corporation ICH9M LPC Interface Controller (rev 03) 00:1f.2 SATA controller: Intel Corporation 82801IBM/IEM (ICH9M/ICH9M-E) 4 port SATA Controller [AHCI mode] (rev 03) 00:1f.3 SMBus: Intel Corporation 82801I (ICH9 Family) SMBus Controller (rev 03) 01:00.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI RV710 [Mobility Radeon HD 4500/5100 Series] 01:00.1 Audio device: Advanced Micro Devices [AMD] nee ATI RV710/730 HDMI Audio [Radeon HD 4000 series] 02:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8057 PCI-E Gigabit Ethernet Controller (rev 10) 03:00.0 Network controller: Atheros Communications Inc. AR928X Wireless Network Adapter (PCI-Express) (rev 01) 0c:03.0 FireWire (IEEE 1394): Ricoh Co Ltd R5C832 IEEE 1394 Controller (rev 05) 0c:03.1 SD Host controller: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter (rev 22) 0c:03.2 System peripheral: Ricoh Co Ltd R5C592 Memory Stick Bus Host Adapter (rev 12) lshw -c network output *-network descripción: Ethernet interface producto: 88E8057 PCI-E Gigabit Ethernet Controller fabricante: Marvell Technology Group Ltd. id físico: 0 información del bus: pci@0000:02:00.0 nombre lógico: eth0 versión: 10 serie: 00:24:be:83:b2:4f tamaño: 100Mbit/s capacidad: 1Gbit/s anchura: 64 bits reloj: 33MHz capacidades: pm msi pciexpress bus_master cap_list rom ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuración: autonegotiation=on broadcast=yes driver=sky2 driverversion=1.30 duplex=full ip=192.168.1.123 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s recursos: irq:45 memoria:d3520000-d3523fff ioport:c000(size=256) memoria:d3500000-d351ffff *-network DESACTIVADO descripción: Interfaz inalámbrica producto: AR928X Wireless Network Adapter (PCI-Express) fabricante: Atheros Communications Inc. id físico: 0 información del bus: pci@0000:03:00.0 nombre lógico: wlan0 versión: 01 serie: 2c:81:58:e6:b6:03 anchura: 64 bits reloj: 33MHz capacidades: pm msi pciexpress msix bus_master cap_list ethernet physical wireless configuración: broadcast=yes driver=ath9k driverversion=3.5.0-18-generic firmware=N/A latency=0 link=no multicast=yes wireless=IEEE 802.11bgn recursos: irq:17 memoria:d2100000-d210ffff rfkill list all output 0: phy0: Wireless LAN Soft blocked: yes Hard blocked: yes 1: sony-wifi: Wireless LAN Soft blocked: yes Hard blocked: no

  Read the article

• Broadcom bcm4313 Ubuntu 13.10 connection time out

  - by Wahtever

  After upgrading to Ubuntu 13.10 I keep getting connection timed out every few seconds at which point i have to disconnect and reconnect to the WiFi network. The WiFi card worked fine on 13.04 with the bcmwl-kernel-source installed but giving problems on 13.10: *-network description: Wireless interface product: BCM4313 802.11bgn Wireless Network Adapter vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: eth1 version: 01 serial: c0:14:3d:cc:c9:c7 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=6.30.223.141 (r415941) ip=192.168.1.4 latency=0 multicast=yes wireless=IEEE 802.11abg resources: irq:17 memory:f0500000-f0503fff How can i fix this? Thanks

  Read the article

• No Internet Connection - ubuntu 11.10

  - by emersonhsieh

  I installed Ubuntu 11.10 recently. After the first bootup the computer freezes so I have to force-quit my computer. Then I turned on my computer after that. I tried connecting to the internet. My (and my neighbor's) wireless networks shown up, but no matter how many times I tried, I can't connect to my home network. I checked the password and the other laptop's internet works (a MacBookPro). It was a wireless network. What's weird is that the Wireless network worked when I was installing ubuntu How can I connect to the internet now? I don't have a wired network. Please Help! Any help will be appreciated Specs: ASUS F81Se, Windows 7 Dual-boot, I remember the wireless card was made by Atheros, 4GB RAM

  Read the article

• ADO.NET Entity Framework with OLE DB Access Data Source

  - by Tim Long

  Has anyone found a way to make the ADO.NET Entity Framework work with OLE DB or ODBC data sources? Specifically, I need to work with an Access database that for various reasons can't be upsized to SQL. This MSDN page says: The .NET Framework includes ADO.NET providers for direct access to Microsoft SQL Server (including Entity Framework support), and for indirect access to other databases with ODBC and OLE DB drivers (see .NET Framework Data Providers). For direct access to other databases, many third-party providers are available as shown below. The reference to "indirect access to other databases" is tantalising but I confess that I am hopelessly confused by all the different names for data access technology.

  Read the article

• Cisco 800 series won't forward port

  - by sam

  Hello ServerFault, I am trying to forward port 444 from my cisco router to my Web Server (192.168.0.2). As far as I can tell, my port forwarding is configured correctly, yet no traffic will pass through on port 444. Here is my config: ! version 12.3 service config no service pad service tcp-keepalives-in service tcp-keepalives-out service timestamps debug uptime service timestamps log uptime service password-encryption no service dhcp ! hostname QUESTMOUNT ! logging buffered 16386 informational logging rate-limit 100 except warnings no logging console no logging monitor enable secret 5 -removed- ! username administrator secret 5 -removed- username manager secret 5 -removed- clock timezone NZST 12 clock summer-time NZDT recurring 1 Sun Oct 2:00 3 Sun Mar 3:00 aaa new-model ! ! aaa authentication login default local aaa authentication login userlist local aaa authentication ppp default local aaa authorization network grouplist local aaa session-id common ip subnet-zero no ip source-route no ip domain lookup ip domain name quest.local ! ! no ip bootp server ip inspect name firewall tcp ip inspect name firewall udp ip inspect name firewall cuseeme ip inspect name firewall h323 ip inspect name firewall rcmd ip inspect name firewall realaudio ip inspect name firewall streamworks ip inspect name firewall vdolive ip inspect name firewall sqlnet ip inspect name firewall tftp ip inspect name firewall ftp ip inspect name firewall icmp ip inspect name firewall sip ip inspect name firewall fragment maximum 256 timeout 1 ip inspect name firewall netshow ip inspect name firewall rtsp ip inspect name firewall skinny ip inspect name firewall http ip audit notify log ip audit po max-events 100 ip audit name intrusion info list 3 action alarm ip audit name intrusion attack list 3 action alarm drop reset no ftp-server write-enable ! ! ! ! crypto isakmp policy 1 authentication pre-share ! crypto isakmp policy 2 encr 3des authentication pre-share group 2 ! crypto isakmp client configuration group staff key 0 qS;,sc:q<skro1^, domain quest.local pool vpnclients acl 106 ! ! crypto ipsec transform-set tr-null-sha esp-null esp-sha-hmac crypto ipsec transform-set tr-des-md5 esp-des esp-md5-hmac crypto ipsec transform-set tr-des-sha esp-des esp-sha-hmac crypto ipsec transform-set tr-3des-sha esp-3des esp-sha-hmac ! crypto dynamic-map vpnusers 1 description Client to Site VPN Users set transform-set tr-des-md5 ! ! crypto map cm-cryptomap client authentication list userlist crypto map cm-cryptomap isakmp authorization list grouplist crypto map cm-cryptomap client configuration address respond crypto map cm-cryptomap 65000 ipsec-isakmp dynamic vpnusers ! ! ! ! interface Ethernet0 ip address 192.168.0.254 255.255.255.0 ip access-group 102 in ip nat inside hold-queue 100 out ! interface ATM0 no ip address no atm ilmi-keepalive dsl operating-mode auto ! interface ATM0.1 point-to-point pvc 0/100 encapsulation aal5mux ppp dialer dialer pool-member 1 ! ! interface Dialer0 bandwidth 640 ip address negotiated ip access-group 101 in no ip redirects no ip unreachables ip nat outside ip inspect firewall out ip audit intrusion in encapsulation ppp no ip route-cache no ip mroute-cache dialer pool 1 dialer-group 1 no cdp enable ppp pap sent-username -removed- password 7 -removed- ppp ipcp dns request crypto map cm-cryptomap ! ip local pool vpnclients 192.168.99.1 192.168.99.254 ip nat inside source list 105 interface Dialer0 overload ip nat inside source static tcp 192.168.0.2 444 interface Dialer0 444 ip nat inside source static tcp 192.168.0.51 9000 interface Dialer0 9000 ip nat inside source static udp 192.168.0.2 1433 interface Dialer0 1433 ip nat inside source static tcp 192.168.0.2 1433 interface Dialer0 1433 ip nat inside source static tcp 192.168.0.2 25 interface Dialer0 25 ip classless ip route 0.0.0.0 0.0.0.0 Dialer0 ip http server no ip http secure-server ! ip access-list logging interval 10 logging 192.168.0.2 access-list 1 remark The local LAN. access-list 1 permit 192.168.0.0 0.0.0.255 access-list 2 permit 192.168.0.0 access-list 2 remark Where management can be done from. access-list 2 permit 192.168.0.0 0.0.0.255 access-list 3 remark Traffic not to check for intrustion detection. access-list 3 deny 192.168.99.0 0.0.0.255 access-list 3 permit any access-list 101 remark Traffic allowed to enter the router from the Internet access-list 101 permit ip 192.168.99.0 0.0.0.255 192.168.0.0 0.0.0.255 access-list 101 deny ip 0.0.0.0 0.255.255.255 any access-list 101 deny ip 10.0.0.0 0.255.255.255 any access-list 101 deny ip 127.0.0.0 0.255.255.255 any access-list 101 deny ip 169.254.0.0 0.0.255.255 any access-list 101 deny ip 172.16.0.0 0.15.255.255 any access-list 101 deny ip 192.0.2.0 0.0.0.255 any access-list 101 deny ip 192.168.0.0 0.0.255.255 any access-list 101 deny ip 198.18.0.0 0.1.255.255 any access-list 101 deny ip 224.0.0.0 0.15.255.255 any access-list 101 deny ip any host 255.255.255.255 access-list 101 permit tcp 67.228.209.128 0.0.0.15 any eq 1433 access-list 101 permit tcp host 120.136.2.22 any eq 1433 access-list 101 permit tcp host 123.100.90.58 any eq 1433 access-list 101 permit udp 67.228.209.128 0.0.0.15 any eq 1433 access-list 101 permit udp host 120.136.2.22 any eq 1433 access-list 101 permit udp host 123.100.90.58 any eq 1433 access-list 101 permit tcp any any eq 444 access-list 101 permit tcp any any eq 9000 access-list 101 permit tcp any any eq smtp access-list 101 permit udp any any eq non500-isakmp access-list 101 permit udp any any eq isakmp access-list 101 permit esp any any access-list 101 permit tcp any any eq 1723 access-list 101 permit gre any any access-list 101 permit tcp any any eq 22 access-list 101 permit tcp any any eq telnet access-list 102 remark Traffic allowed to enter the router from the Ethernet access-list 102 permit ip any host 192.168.0.254 access-list 102 deny ip any host 192.168.0.255 access-list 102 deny udp any any eq tftp log access-list 102 permit ip 192.168.0.0 0.0.0.255 192.168.99.0 0.0.0.255 access-list 102 deny ip any 0.0.0.0 0.255.255.255 log access-list 102 deny ip any 10.0.0.0 0.255.255.255 log access-list 102 deny ip any 127.0.0.0 0.255.255.255 log access-list 102 deny ip any 169.254.0.0 0.0.255.255 log access-list 102 deny ip any 172.16.0.0 0.15.255.255 log access-list 102 deny ip any 192.0.2.0 0.0.0.255 log access-list 102 deny ip any 192.168.0.0 0.0.255.255 log access-list 102 deny ip any 198.18.0.0 0.1.255.255 log access-list 102 deny udp any any eq 135 log access-list 102 deny tcp any any eq 135 log access-list 102 deny udp any any eq netbios-ns log access-list 102 deny udp any any eq netbios-dgm log access-list 102 deny tcp any any eq 445 log access-list 102 permit ip 192.168.0.0 0.0.0.255 any access-list 102 permit ip any host 255.255.255.255 access-list 102 deny ip any any log access-list 105 remark Traffic to NAT access-list 105 deny ip 192.168.0.0 0.0.0.255 192.168.99.0 0.0.0.255 access-list 105 permit ip 192.168.0.0 0.0.0.255 any access-list 106 remark User to Site VPN Clients access-list 106 permit ip 192.168.0.0 0.0.0.255 any dialer-list 1 protocol ip permit ! line con 0 no modem enable line aux 0 line vty 0 4 access-class 2 in transport input telnet ssh transport output none ! scheduler max-task-time 5000 ! end any ideas? :)

  Read the article

• Allowing access to subnets openvpn access server

  - by user3882976

  I have a centos server running a openvpn access server. On that server I am running a windows server in virtual box. On the centos server I am running the vpn with a network address 172.27.224.0 with 20 bits. The windows server is running a dchp server giving ip's of 192.168.1.0-200. When i try to connect to the widows shared folder from the vpn i can't using the name of the server but i can from the ip.

  Read the article

• Archlinux/atheros WLAN configuration troubles

  - by GrinReaper

  I'm trying to config archlinux to use my wireless network adapter. It's quite troublesome. From what I've gathered, it's an atheros network adapter, using the ath5k driver/module... I can't get it to work; any ideas? Here's some of the output from my tinkering: # lspci | grep -i net 00:0a.0 Ethernet controller: nVidia corporation MCP67 Ethernet (reva2) 03:00.0 Ethernet controller: atheros communications inc. AR5001 Wireless Network Adapter (rev01) # lsusb ... Bus 004 Device 003: ID 03f0:17d Hewlett Packard Wireless (Bluetooth + WLAN Interface [Integrated Module] # ping -c 3 www.google.com ping: unknown host www.google.com #ping -c 3 8.8.8.8 ping: network is unreachable # lspci -v 03:00.0 Ethernet controller: atheros communications inc. AR5001 Wireless Network Adapter (rev01) ... Kernel driver in use: ath5k Kernel modules: ath5k # dmesg |grep ath5k registered as phy0 registered led device ath5k: atheros chip found PCI INT A disabled registered led device registered as phy1 # ip addr | sed '/^[0-9]/!d;s/: <.*$//' 1: lo 2: eth1 3: eth0 # ip link set <interface> up/down RNETLINK answers: Operation not possible due to RF-kill Also, is there a way to dump text from command-line to a text file so i can just copy pasta? Sorry, first time using a linux distro... EDIT: So I just tried this: I actually just did this twice. (I can't tell which setting is on/off for my wireless adapter. The lights are blue all the time now.) #rfkill list 0: hp-wifi: wireless lan softblocked: no hardblocked :yes 1: hp-bluetooth: bluetooth softblocked: no hardblocked :yes 3: phy1: wireless lan softblocked: no hardblocked :yes #rfkill list 0: hp-wifi: wireless lan softblocked: no hardblocked :no 1: hp-bluetooth: bluetooth softblocked: no hardblocked no 3: phy1: wireless lan softblocked: no hardblocked :yes 7: hci0: bluetooh 0: hp-wifi: wireless lan softblocked: no hardblocked :no I've dug around some other articles and it seems like ath5k is supposed to be preferable to madwifi, so should i be using madwifi? I'm 99% sure I disabled the hardblock (by turning it ON) but, as shown above, phy1 wireless lan is STILL hardblocked. What gives? Maybe I've made some more fundamental error in a basic config file? EDIT: I've fixed the hardblock. I've tried pinging www.google.com, but to no avail. I get: ping: unknown host www.google.com In the arch wiki: Edit /etc/hosts and add the same HOSTNAME you entered in /etc/rc.conf: 127.0.0.1 archlinux.domain.org localhost.localdomain localhost archlinux To my understanding, hostname is just a user-specified and based on preference(?) My /etc/rc.conf: HOSTNAME="gestalt" My /etc/hosts: 127.0.0.1 localhost.localdomain localhost gestalt but should it be the following? 120.0.0.1 localhost.domain.org localhost.localdomain localhost gestalt

  Read the article

• iOS Facebook Access Token To Get User Wall Feed (status)

  - by Felix

  [DISCLAIMER : None of the access token or ID below here are real] I've done research for three solid days and no result on how to get user wall feed(post). I have used https://graph.facebook.com/oauth/access_token?client_id=YOUR_APP_ID&client_secret=YOUR_APP_SECRET&grant_type=client_credentials and get the access token which is something like this access_token=454345994651138|bAMGfuW-ueNXGCahley7ga125HN and then https://graph.facebook.com/100005939123542/feed?access_token=454345994651138|bAMGfuW-ueNXGCahley7ga125HN It gives me general information such as user's likes, name, id, current city... but NOT user's wall posts. I've learned that there are three types of access token, which is App Token, User Token, and Page Token. In order to get user/feed by using graphAPI, I need to request to get User Token, but there's NO information in the lousy Facebook Doc! (Which frustrated me the most!) In order to generate the user access token, we need to set some permission, generate the access token, and GET the user's wall feed, which is in JSON format. My question is : How do I get the User Access Token in order to get user wall post in iOS Xcode?

  Read the article

• DB user can see no table using ODBC link in MS Access

  - by bpraveen

  Hi, We are facing an issue with MS access. There are two users having the same access for tables and previliges in database. But one user can access the tables from MS access and another user can't. Can you please let me know the reason. Thanks for updating from options. I am looking in to it. User having grant permissions for SELECT ANY TABLE, it works for SQL connection (E.g. Toad or SQL +), but not for MS Access Is there any issue with MS-Access. Please update me.

  Read the article

• MS Access questions - Scalability / indexing / transactions

  - by oo

  A few questions on MS Access databases - Size: Are there limits to the size of an access database? The reason i ask is that we have an access database that has a few simple tables. The size of the db is about 1GB. When I do a query on it, i see it taking over 10 minutes to run. With proper indexing, should MS Access be able to handle this or are there fundamental limitations to the technology. This is MS Access XP. Also, does MS Access support db transactions, commit and rollback?

  Read the article

• What is the best way to setup a public and private wireless access point on the same home network?

  - by Dougman

  For my home network (with internet provided from a cable modem) I would like to setup a secure wireless access point that I use for all of my personal connections (home PC, iPhone, Xbox, etc) and also another public access point that friends and folks in the neighborhood may connect to (for good karma). I want to ensure that my private traffic cannot be accessed from users of the public access point. I currently have one router that is running the Tomato firmware that I use with WPA security. What is the best way to accomplish this kind of setup securely (if it is possible in a home environment)?

  Read the article

• IBM laptop remove access-connections

  - by Kevin

  I installed IBM Access Connections on my IBM t61 laptop to manage my wireless connections but it simply will not connect to my network. I want to uninstall it and try the Intel software which is capable to performing the same task. However, when I go into "Control Panel" - "Add/Remove Programs" and try to "Remove" this package, it simply opens up a screen and closes it immediately. This happens too fast for me to see whether its an error. Has anyone encountered this issue ? The event logs do not show any error.

  Read the article

• Cannot find wireless driver for HP laptop

  - by rodey

  I have an HP laptop (model: dv7-1267cl, Windows 7 64-bit Home Premium) and I cannot find the wireless driver for the laptop. I am need of a different version because my wireless connection under Windows is flaky and unreliable. I have problems printing to my wireless printer and logging in to and using several sites like reddit.com, phoenix.edu and facebook.com - I get several "page cannot be displayed" messages while using my wireless connection. I disable my wireless adapter and use an ethernet cable and it all works fine. I also used an Ubuntu Live CD to confirm that there is not a problem with the hardware. This is software/driver issue. The drivers were auto installed by the OS. The Device Manager shows the wireless adapter as Atheros AR5009 802.11 a/g/n WiFi Adapter. I have checked the HP website for my laptop and they do not have wireless drivers listed for that model wireless adapter. I have also checked with atheros.com and I do not see my model adapter on their list of available hardware. Device Manager lists the Hardware ID's for my adapter as: PCI\VEN_168C&DEV_002A&SUBSYS_1381103C&REV_01 PCI\VEN_168C&DEV_002A&SUBSYS_1381103C PCI\VEN_168C&DEV_002A&CC_028000 PCI\VEN_168C&DEV_002A&CC_0280 A search for the first Hardware ID turned up this question from experts-exchange.com. tl;dr A driver does not exist for that model adapter.

  Read the article

• Weird Apache Access Logs

  - by user38480

  I see repeated requests like these in my Apache Access Logs and they have been eating up all my CPU. I have a normal WordPress installation. All i changed in the Apache Configuration was changing the DocumentRoot from /var/www/html to /var/www for both ssl and the default configuration. Also, the file referenced in the requests(updatedll.jpeg) does not exist on my server and also isn't referenced in the source code served by any page of the web application. Could this be a security threat? What are these actually and what can i do to stop them. I changed the ip address of my server. They still kept coming. Meaning that somebody is actually hitting the domain name and not the ip address. Why does my server send a 301 for these requests? Shouldn't it be sending a 404? Is it because Wordpress is installed in my root directory and the .htaccess file present for Wordpress is sending a 301 redirect? My disk access logs also seem to have high peaks intermittently. But nobody is actually accessing the site. I see no access logs except these below. Also, i see that all the requests seem to be coming from one of the following 5 ip addresses. 201.4.132.43 - - [05/Jun/2014:07:35:08 -0400] "GET /updatedll.jpg HTTP/1.1" 301 465 "-" "Mozilla/4.0 (compatible; MSIE 7.0; Windows NT 6.1; WOW64; Trident/4.0; BTRS103681; GTB7.5; SLCC2; .NET CLR 2.0.50727; .NET CLR 3.5.30729; .NET CLR 3.0.30729; InfoPath.2; OfficeLiveConnector.1.3; OfficeLivePatch.0.0; AskTbATU3/5.15.29.67612; BRI/2)" 187.40.241.48 - - [05/Jun/2014:07:35:08 -0400] "GET /updatedll.jpg HTTP/1.1" 301 465 "-" "Mozilla/4.0 (compatible; MSIE 7.0; Windows NT 5.1; Trident/4.0; GTB7.5; .NET CLR 2.0.50727; .NET CLR 3.0.4506.2152; .NET CLR 3.5.30729)" 186.56.134.132 - - [05/Jun/2014:07:35:10 -0400] "GET /updatedll.jpg HTTP/1.0" 301 428 "-" "Mozilla/4.0 (compatible; MSIE 6.0; Windows NT 5.1; SV1; .NET CLR 1.1.4322)" 71.223.252.14 - - [05/Jun/2014:07:35:13 -0400] "GET /updatedll.jpg HTTP/1.1" 301 465 "-" "Mozilla/4.0 (compatible; MSIE 7.0; Windows NT 5.1; Trident/4.0; BTRS31756; GTB7.5; .NET CLR 1.1.4322; .NET CLR 2.0.50727; .NET CLR 3.0.4506.2152; .NET CLR 3.5.30729; .NET4.0C; .NET4.0E; InfoPath.2)" 85.245.229.167 - - [05/Jun/2014:07:35:14 -0400] "GET /updatedll.jpg HTTP/1.1" 301 465 "-" "Mozilla/4.0 (compatible; MSIE 7.0; Windows NT 6.1; Trident/7.0; SLCC2; .NET CLR 2.0.50727; .NET CLR 3.5.30729; .NET CLR 3.0.30729; MAAU; .NET4.0C; BRI/2; .NET4.0E; MAAU)"

  Read the article

• Remotely managing Scheduled Tasks on another computer: Access Denied

  - by Eptin

  I need to remotely create new scheduled tasks from a Windows 7 computer in my company (which according to this Microsoft TechNet article I should be able to do. http://technet.microsoft.com/en-us/library/cc766266.aspx ) From within Task Scheduler, on the menu I click Action Connect to another Computer. I browse for the remote computer's name (I use Check Names to verify that the name is correct) and then I check 'Connect as another user' and enter \Administrator and the local admin password. Whenever I try this, I get the error message Task Scheduler: You do not have permission to access this computer Firewall isn't the problem I am able to use Remote Desktop with this username & password combo, so I would expect it to work when remotely managing as well. The remote computer has firewall exceptions for Remote Scheduled Tasks Management, Remote Service Management, and Remote Desktop among other things. Heck, I even tried turning off the firewall for that individual computer and it still didn't work. More details: I have administrative remote access to several other Windows 7 Enterprise computers, though I log in as the local Administrator (whose administrative rights are only recognized by that local machine, not by the domain). The computer I am managing from is on the domain, and also has administrative rights that are recognized on the domain. More experimentation: If I go the other way around and remote-desktop into the other machine and from there open task scheduler then 'connect to another computer', I am able to connect back to my main computer using the username & password that is recognized by an administrator on the domain, and successfully schedule a task on my main computer. So it's not a company firewall issue that's preventing anything from working. The only permissions requirement Microsoft talks about is "The user credentials that you use to connect to the remote computer must be a member of the Administrators group on the remote computer". I'm logging in as an Administrator on each of the local machines, so why doesn't it work?

  Read the article

• How to Turn Your Ubuntu Laptop into a Wireless Access Point

  - by Chris Hoffman

  If you have a single wired Internet connection – say, in a hotel room – you can create an ad-hoc wireless network with Ubuntu and share the Internet connection among multiple devices. Ubuntu includes an easy, graphical setup tool. Unfortunately, there are some limitations. Some devices may not support ad-hoc wireless networks and Ubuntu can only create wireless hotspots with weak WEP encryption, not strong WPA encryption. HTG Explains: What Is RSS and How Can I Benefit From Using It? HTG Explains: Why You Only Have to Wipe a Disk Once to Erase It HTG Explains: Learn How Websites Are Tracking You Online

  Read the article

• Have local admin privileges on Windows XP, but getting "Error terminating process: Access is denied"

  - by Chris W. Rea

  On one of the Windows XP machines I use regularly, there is a process that starts up periodically. I'd like to be able to kill the process – sometimes – because it occasionally runs when I'm busy doing something machine-intensive. I've already tried dropping the process priority to "Idle" to mitigate the effects, but it isn't the CPU that's the problem. Rather, the process is very disk-intensive and no matter the process priority, it still causes significant disk thrashing when running, impacting everything else I'm doing at the time. Using Process Explorer, I can find the process, right-click, and choose Kill Process, but I always get the message "Error terminating process: Access is denied." This is not an operating system process, but third-party software. What might that process be doing to prevent itself from being terminated? How can I kill such a process? Is there a way for me to modify the process's security or access control list (ACL) somewhere, using Process Explorer or another tool, so that I can effectively kill it?

  Read the article

• compiling compat-wireless fails at 'make' with 'make: *** [modules] Error 2'

  - by Paul Carter

  Trying to compile the compat-wireless-2012-09-25 driver module, without success. scrips/driver-select alx ; works make ; fails - scripts/Makefile.build:44 ~/sourcecode/compat-wireless-2012-09-25.2/drivers/net/ethernet/atheros/alx/Makefile: No such file or directory make[4]: ** No rule to make target '~/sourcecode/compat-wireless-2012-09-25.2/drivers/net/ethernet/atheros/alx/Makefile'. Stop. [snip] make: * [modules] Error 2 Device is Atheros AR8161 wired ethernet in a Dell Vostro 3460. I'd be very grateful for assistance in getting this to compile.

  Read the article

• Interesting phenomenom with Windows Server 2008 R2 user access controls and NTFS ACLs

  - by Simon Catlin

  One to try, and I'd appreciate any thoughts on this. On a Windows Server 2008 R2 box (or presumably 2008 R1, Windows Vista or Windows 7): i) Logon as an administrator, and create a new NTFS volume ii) Blow away the standard MS ACLS on the root of the volume (which are laughable), and replace with Administrators:Full Control, System:Full Control, e.g.: echo Y|cacls.exe d:\ /g "Administrators:F" "SYSTEM:F" iii) Now, from a Command Prompt shell window or PowerShell window, switch to that drive (cd /d D:\ or set-location D:\ ). Works fine... no issues. iv) Now, try to browse to the root of the new volume using MS Explorer... Access denied. Now, I've kind of convinced myself that it is UAC getting in the way, as you can add "Authenticated Users:List" access to D:\ and Explorer then works. I can only assume that MS Explorer isn't able to use the "admin" token for the Administrator. Browsing to explorer.exe and doing a "Run as administrator" has no effect. Any thoughts? Cheers in advance.

  Read the article

• Broadcom STA wireless driver frezees

  - by Srki

  Upon updating my 10.10 netbook to 11.04 on the first startup it froze. I checked the forums and found that disabling wlan in BIOS fixes the problem so I did that and it worked, system was ok and it didn't freeze but then I had no wireless. I know that Broadcom STA driver is to blame cause I removed it from "additional drivers" and enabled back in bios wlan and everything worked fine (exept no wireless cause no driver is activated). Enabling Broadcom STA in the additional drivers again and restarting wireless was up and it found my network and connected to it but in a matter of seconds netbook froze. Can you please help me...

  Read the article

• Access 2010 datasheet view only/relationships unavailable

  - by Luis

  I'm relatively new to MS Access in general and just started working with Access 2010. I've created a new web database with a few tables that I need to relate. First problem: For the life of me, I can't view anything in any view other than datasheet view; everywhere I would expect to be able to change the view, only datasheet view is available. Second problem: I can't change the primary key(s). Presumably I would be able to do this if I could get out of datasheet view and into design view. Third problem: The 'Relationships' button is greyed out. I know these appear to be really simple things but I've been looking for much more time than I'd like to admit trying to figure out how to get unstuck. Update: It would appear that this is happening because it is a 'web database' as I've been able to do all of the above in a new regular database. With this in mind let me ask a different question: Am I able to add relationships and change primary keys in a web database? If so how? More generally, what is the point of a web database?

  Read the article

< Previous Page | 55 56 57 58 59 60 61 62 63 64 65 66  | Next Page >