Search Results

Search found 20785 results on 832 pages for 'idea'.

Page 590/832 | < Previous Page | 586 587 588 589 590 591 592 593 594 595 596 597  | Next Page >

• PC won't PXE boot to WDS/MDT with Dell Optiplex 755

  - by Moman10

  I am trying to set up a basic MDT solution. I have set one up in the past at a previous job and it worked flawlessly, however here I'm running into a problem and am having no luck getting around it. I've installed Windows Server 2012 and MDT 2013, along with adding on the WDS role. I haven't configured much outside of the defaults for WDS, basically just set PXE response to respond to all clients (and unchecked admin approval). This machine does not run a DHCP server. I looked on the DHCP scope of our DHCP server, it shows options 66/67 checked and the server name of the WDS server is in there as well. I didn't add this but I assume it was put on during the install process (I believe I had to manually make some adjustments at my old job for this). The PC I have is a Dell Optiplex 755. I have enabled the onbard NIC w/PXE boot option in BIOS and attempted to boot. I get a "TFTP...." error but nothing offering out a DHCP address like I'm used to. In my previous job it pretty much worked right out of the box. I've verified that PortFast is enabled on the port and I've tried a couple different PCs (but both are the same model, only model I have to work with). No matter what, I get the same error. The subnet the PC is in is a different subnet than where the WDS server is sitting, but there are IP helper statements on the switch and the PCs can get regular DHCP addresses just fine from the DHCP server, just doesn't seem to get offered out a PXE boot option. I don't know if the problem is a configuration with the server or the PC itself...but after a few days of Googling I'm running out of ideas. Does anyone have a good idea of something it may be?

  Read the article

• IIS 7.5 stops serving requests for no apparent reason

  - by Steffen

  We're running a site on 4 virtual Win 2008 R2 64 bit servers. This is the only site on the IIS, and we use Windows Network Load Balancing to share the load between our 4 virtual servers. We've used these virtual servers for approximately a week, and we're starting to see some issues. For no apparent reason the IIS stops serving pages, and doesn't even respond with an error. So upon requesting a page from the server, the browser just waits infinitely (or until it decides to give up clientside) Sometimes an iisreset fixes the issue, other times we have to reboot the entire virtual server. There are no traces in the eventlog of why this happens, and there's no traces in our applications exception log neither. Furthermore this happens even when there's a very small load on the server, so it doesn't seem to be because it's flooded with requests. So frankly I'm at a loss here - I have no idea where to start debugging this issue :-( I'm quite certain we never had these issues on our physical servers, however they were running Win 2003 32bit, so there are quite a few differences between them and the virtual ones. (Which obviously makes it difficult to tell what exactly causes this)

  Read the article

• Unexplained cache RAM drops on Linux machine

  - by FunkyChicken

  I run a CentOS 5.7 64 machine with 24gb ram and running kernel 2.6.18-274.12.1.el5. This machine runs only Nginx, php-fpm and Xcache as extra applications. Since about 3 weeks my memory behavior on this machine has changed and I cannot explain why. There are no crons running which flush anything like this. There are also no large numbers of files being deleted/changed during these drops. The 'cached' memory gets dropped about every few hours, but it's never a set gap between flushes, this indicates to me that some bottleneck gets reached instead. It also always seems to be when total memory usages gets to about 18GB, but again, not always exactly 18GB. This is a graph of my memory usage: As you can see in the graph the 'buffers' always stay more or less the same, it is mainly the 'cache' that gets dropped. Running vmstat -m I have outputted the memory usage just before and just after a memory drop. The output is here: http://pastebin.com/diff.php?i=hJqZqztm 'old version' being before, 'new version' being after a drop. About 3 weeks ago my server crashed during a heavy DDOS attack, after I rebooted the machine this odd behavior started. I have checked a bunch of logs, restarted the machine again, and cannot find any indication what changed. During these 'cache' memory drops, my iNode usage drops at the same time. Does anyone have any idea what might be causing this behavior? Clearly my RAM isn't full, so I am curious why this could be happening.

  Read the article

• Is there a way in Windows 7 to disable "journaling"?

  - by Psycogeek

  C:\$extend\$Usn.Jrnl:$J:$data Here is a picture finally. The large strip in the center of the top band is the largest chunk, in the other, grey areas are the various clusters with it. On the right, the big long grey line is $logfile (not paging), and it is 63&nbsb;MB. Paging, 500&nbsb;MB is the dark cyan chunk, next to the yellow MFTres in the inner rings.. The disk was defragged so they could be seen easier. Not all clusters of this type of file are tagged, but the idea is there. The disk is 4k clusters, now about 12 GB size. Each cute little block in the picture is .81 MB and represents 207 clusters. The dkGreen section, is mostly the whole Winsxs pile, also interesting when they keep telling us it doesn't take much disk space. Wikipedia suggests that in previous NT systems "USN journaling" would be turned on when enabled (assumes it could also be turned off?). What aspects, services, or program is working on putting that stuff all over the disk which is known by $jrnl$ type clusters, even if it is not actual USN journaling? Is it possible in a Windows 7 system to completly disable the journaling, and what would be the ramifications of that? On a Windows XP NTFS system, I do not recall seeing the quantity of disk clusters used with these $jrnl$ names, so I do not recall this being necessary in this quantity for an NTFS file system itself? I understand that it would not be there, if it did not have a useful function :-) Information about how wonderful is fine, if that information will help track down what parts of the system create and use it. Change Journals states: Change journals are also needed to recover file system indexing Hmm, that might explain some of them, or why it was left on the disk. A crash while background indexing?

  Read the article

• My Boot order changed. Why?

  - by Chris

  I have a laptop running Windows XP SP3 with one internal hard drive partitioned into C: (system), D: (storage) and I have an external hard drive, F: (external drive). Yesterday the machine was running fine. Today, I go back to it and see that it's just showing a blinking cursor. Checked through the BIOS and the hard drive checked out fine. CTRL-ALT-DELETED the machine a few times, but I was never able to boot back into the operating system. I threw in a live CD and found out that the boot order of the drives has changed. The external drive is now C:, the system partiton is D:, and the storage partition is E:. Does anyone have any idea of how or why this would have occured? Auto system updates are turned off so there should have been no automatic reboot of the system overnight, and anti-virius runs on the machine and has found no infections before this occured. Edit When I was looking through the BIOS of the machine, I did see that the boot order was changed. But still the same question remains, what would have caused this to happen? I can't believe that a random reboot happened and totally changed my hard drive setup.

  Read the article

• Active Directory + IIS + SQL + ASP.NET

  - by Amira Elsayed Ismail

  I have sent the following question to stackoverflow website I have installed Windows server 2008 r2 on a virtual machine, Can I install Active directory with domain controller + IIS + SQL server on the same machine? I want to make web application and this web application will authenticate users from Active Directory, the web application should be published on the server IIS and the users should access it remotely from their home using domain name of my machine, Someone tell me that its very wrong to have IIS and Active directory on the same machine I got the following Answer You can't use ActiveDirectory over the internet. At least not without something like a VPN as a middle man. Their home computers will not be joined to the domain, so there is no pass-through authentication. Yes, it's a bad idea to put AD on the web server. Why is too complex to get into in an answer here. Suffice it to say that even if you did do this, it's probably would not work the way you are thinking it should. It's not impossible to do this. For instance, many of the Microsoft "Small Businesss" products put IIS, AD, and SQL Server on the same server. But, you kind of have to know what you're doing to configure it securely. Then I add the following comment Thanks for ur reply.so what you think about the best way to do this as I didn't do anything like that before should I install active directory on a machine and IIS on another machine ? and what about SQL should I add it to the same server of active directory ? I didn't mentioned also that it will be Microsoft dynamics server that will access some information about work and i have to read data from axapta also ? also what is VPN and how can I use it to let users access my web application anywhere ? Sorry for my long questions and thanks in advance so please if anyone can help I will be thankful

  Read the article

• Setup Entourage for Exchange via HTTP communication

  - by Johandk

  Our ISP set up a hosted exchange server for all our mail. I've setup all our Outlook users with no problems. We have two people using Mac OSX Leopard and Entourage. Entourage has the option of adding an Exchange account, but I have no idea how to tell it to connect to exchange via HTTP. Heres an excerpt from the client setup docs the hosting company sent me for Outlook: 1 .Go to control panel 2. Select ‘Mail’ 3. Select ‘Email accounts’ Under the E-mail tab select ‘New’ Select ‘Manually configure server settings......’ - click next Select ‘Microsoft Exchange’ – click next Complete details as below with Microsoft Exchange Server as: [server address] Do not select ‘Check Name’. Instead select ‘More Settings’. Go to the Connection tab, and select the bottom option ‘Connect to Microsoft Exchange using HTTP’. And then select the ‘Exchange Proxy Settings’ button. Enter Proxy server for Exchange Check Only connect to proxy servers that have this principal name in their certificate, Enter msstd:[servername] Proxy Authentication - select Basic Authentication Select OK, and again, so that you return to the main screen. Now select ‘Check Name’. Enter Username and Password: The username should now be the full name and underlined. If so select next, and then finish. Next time you open Outlook, enter username and password Any help GREATLY appreciated.

  Read the article

• How To Find Reasons of Why Site Goes Online/Offline

  - by HollerTrain

  Seems today a website I manage has been going online and offline throughout the entire day. I have no idea what is causing the issue so I am seeking guidance on where to start. It is a Wordpress based site. So here is what I DO know: I use a program that pings the server every minute and when the server is not responding me it emails me, so I can know exactly when the site is online and offline. The site between 8pm to 12pm 12.28, and around the 1a hour early morning 12.29 (New York City timezone, and all times below are in same timezone). At the time of the ups/downs I see a lot of strain on the memory usage. Look at the load average when the site is going online/offline (http://screencast.com/t/BRlfXkqrbJII). Then I ran this command to restart http (http://screencast.com/t/usVtYWZ2Qi) and the memory usage then goes down to this (http://screencast.com/t/VdTIy3bgZiQB). An hour after I restarted http, the site then went offline/online so restarting the http didn't do much help. When the site is going offline/online, I ran the top command and get this (http://screencast.com/t/zEwr7YQj3). Here is a top command when the site is at it's lowest (http://screencast.com/t/eaMfha9lbT - so this would be dubbged "normal"). Here is a bandwidth report (http://screencast.com/t/AS0h2CH1Gypq). The traffic doesn't seem to be that much (http://screencast.com/t/s7hrWNNic1K), but looking at my times the site is going up/down this may be one of the reasons? I have the dvp Nitro package at Media Temple (http://mediatemple.net/webhosting/nitro/). So at this point I would request some help in trying to figure out what the cause of this is, and how I can go about pinpointing this issue. ANY HELP is greatly appreciated.

  Read the article

• How to install IE9 when KB2120976 is not applicable to my Windows 7 x86 Ultimate edition?

  - by CVertex

  I'm trying to install IE9, visit http://beautyoftheweb.com, download it and then says it's downloading prereqs. After a minute, the installer says there's a problem and directs me to Prerequisites for installing Internet Explorer 9 Beta I click on the x86 installers one by one... most say "already installed".. But http://support.microsoft.com/kb/2120976/ says "The update is not applicable to your computer". Lame. So I try the IE9 install and the go through the whole process again with the same result. I discovered there's an IE9 install log at C:\Windows\IE9_main.log which logs the install process and reports an Error for 2120976 00:06.630: ERROR: Error installing prerequisite file (C:\Users\Vijay\AppData\Local\Temp\IE98036.tmp\KB2120976_x86.msu): 0x80240017 (2149842967) 00:06.677: INFO: PauseOrResumeAUThread: Successfully resumed Automatic Updates. 00:12.090: INFO: Link clicked, opening URL in new window:'http://go.microsoft.com/fwlink/?LinkId=185111' 00:12.106: INFO: Setup exit code: 0x00009C47 (40007) - Required updates are missing from the system.are missing from the system. Any idea why KB2120976 is inapplicable to my LEGAL Windows 7 Ultimate system? Any help is greatly appreciated.

  Read the article

• Disaster recovery backup of files/photos for personal use

  - by Renesis

  I'm looking for the best method to store a backup of important files and 5+ years of digital photos that is safe from some type of fire/flood disaster in my home. I'm looking for: Affordable: Less than $100/yr or first-time cost. Reliable: At least a smaller chance of failing than there is of fire or flood Easy for initial backup and to add to, and at least semi-easy to recover. I recently purchased a small home safe for physical vitals. It was inexpensive, solid, and is fire/water safe. If I had a physical copy of the digital files, the safe would work fine for this, but I don't know what to store in it that adequately meets the requirements above. Hard drive - I read that the danger of it not spinning up makes a hard drive a bad choice for this type of storage, although it was my first thought and would definitely be the simplest choice - very easy to take out once a month and add files to. DVDs - Way too much of a hassle for both backup and restore. Tape - No idea on the affordability of this option Online - Given that I have at least 300GB already and ever-increasing megapixels means ever-bigger files, and my ISP upload is about 2Mb at the best, this just doesn't sound like a good option for me, but I could be convinced. Other - Have I missed something? Also, I'm already covered both for sync between computers (Dropbox) and a nightly backup of these files (External HDD). The problem with the nightly backup is obviously that it's always with the computer and in a disaster would be destroyed along with it. Is anyone else doing something similar? Is the HDD as poor of a choice as I read, or is it a feasible option? Maybe two to reduce the likelihood of failure?

  Read the article

• Exchange backup verification shows no files

  - by Olaf

  [SBS2003SP2] If i read the exhange log it shows the backup contains no files just folders and the total size seems to be Ok. I i try to restore the folders are empty... But the 14 files that where backupped dissapeared in the verification log?! Other backups on the same medium turned out to be fine. Any idea what's wrong here? This is my log: Backup Status Operation: Backup Active backup destination: File Media name: "testbackup.bkf created 2-6-2010 at 11:25" Volume shadow copy creation: Attempt 1. Backup of "SERVER1\Microsoft Information Store\First Storage Group" Backup set #1 on media #1 Backup description: "Set created 2-6-2010 at 11:25" Media name: "testbackup.bkf created 2-6-2010 at 11:25" Backup Type: Normal Backup started on 2-6-2010 at 11:26. Backup completed on 2-6-2010 at 12:21. Directories: 4 Files: 14 Bytes: 26.842.932.104 Time: 55 minutes and 38 seconds Verify Status Operation: Verify After Backup Active backup destination: File Active backup destination: \backup\Server1\Backup Files\testbackup.bkf Verify of "SERVER1\Microsoft Information Store\First Storage Group" Backup set #1 on media #1 Backup description: "Set created 2-6-2010 at 11:25" Verify started on 2-6-2010 at 12:21. Verify completed on 2-6-2010 at 12:47. Directories: 4 Files: 0 Different: 0 Bytes: 26.842.932.104 Time: 25 minutes and 46 seconds

  Read the article

• Windows 2012 RDS Temporary profile for Administrator

  - by Fabio

  I've configured a Windows 2012 RDS Farm with two virtual servers (VMWare - each one on a different ESX server). Both servers have Licensing, Web Access, Gateway, Connection Broker and Session Host roles. High Availability is set up and it works fine. Remote Apps are working and even Windows XP clients have access to the web interface. User profile path is \vmfiles1\UserProfileDisks\App\ and almost everyone has full right access to it. The problem I have is that I would like to be able to access both servers at the same time with the Administrator account (console), but each time I try, the second server that I logon to give me access with a temporary profile. I tried to enable/disable multiple sessions per user and forced Admin logoff with the GPO but nothing changed. Another thing is that the server pool is not saved, so each time I restart the RDS server or I logoff from it, I have to add a server in the server manager. Do you have any idea? Sorry if my english is not perfect.

  Read the article

• SBS 2003 boot stalls at acpitabl.dat

  - by John

  I have a SBS 2003 server running for 3 year without any problems, and few days ago it freezes during the boot. System is using two 500 Gb drives in RAID1 (Intel Matrix 7.5) After trying to load in safe mode, boot stops on acpitabl.dat. First idea was that there is a problem with RAID altough disk status was OK, and RAID status was Rebuild. I tried to boot with each drive, and one gives me the same problem, and the other drive is failing to load. Took both drives out, and checked it on a different machine. One drive is dead, other is without any problems. Returned the good drive back in SBS 2003 with changed status to Degraded, but the problem is still the same. I also have a clean SBS 2003 copy installed on this drive (previous installation), which loads smooth and quick. So, I believe the main problem is this installed version of SBS 2003. Did not make any hardware changes, did not make any updates (not sure about any automatic windows updates lately). Since there are tons posts about this problem, and no clear solution, I am trying to figure how to repair SBS 2003 installation, since there are some installed programs on this installation which I cannot re-install without additional issues.

  Read the article

• How to test server throughput

  - by embwbam

  I've always used apache benchmark to try to get a rough idea of how many requests/second my server can handle. I read that it was good, and it seemed to work well. Enter node.js, which is fully event-based, so it never blocks. If I run apache benchmark on a simple hello world server it can handle 2500 requests per second or so. However, if I put a timeout in the hello world function, so that it responds after 2 seconds, apache benchmark reports a dramatically reduced throughput: about 50/s. I'm running 100 concurrent connections with ab. If I increase the concurrency, it goes up. This makes sense, because apache benchmark is basically sending out requests in batches of 100, which come back every 2 seconds. 100 requests / 2 seconds = 50 requests / second If I increase the concurrency to about 400 or 500, it starts to crash. I don't think I've hit node.js's limit, I think I'm hitting a wall in my operating system on the number of open file descriptors or sockets or something. Any way I can get a good guess about how many requests my server can handle? I want to make sure the test computer isn't the one causing the problem.

  Read the article

• Are there any open source reseller packages?

  - by Tom Wright

  My department has just been given the right/responsibility to manage our own VPS. The idea being that the bureaucracy will be less for the many small web projects we run. Since each project will be managed by a different team, I was planning on approaching a shared hosting model. Are there any free pieces of software that would help automate the provision of resources each time a team request a new project? Most of the projects have identical requirements - basically LAMP - so it would be these resources that I would want provisioning (and de-provisioning, if that is a word) automatically. Ideally, there would also be a way to hook it into our LDAP authentication backend too, though I could probably make this sort of modification if necessary. Since we won't be charging our "client" however, we won't need the ability to generate invoices, handle payments, etc. etc. EDIT: Sample workflow Login authenticated against LDAP Username checked against admin group (not on central LDAP) Click 'new project' and enter project name User created on VPS with project name as username Apache virtual host created and subdomain (using project name) allocated FTP & MySQL users created

  Read the article

• Getting rsync to move file from source to destination ?

  - by fabien-barbier

  Is rsync is a good choice for my project ? I have to : - copy files from source to destination folder via SSH, - be sure all files are copied, - delete source files after copy. - if I have conflict name, I have to rename files. It looks like I can use option : --remove-source-files (to delete source files) But how rsync manage conflict, can I had rules ? Use case on my project : I run scientific calculation on server A and results are inserted in folder "process", for each calculation I have a repository like this : /process/calc1. Now I would like to transfer repository "/calc1" to server B (I get /process/calc1), and delete "calc1" from server A. ...During another calculation I get "/process/calc2" on server A, the idea is also to move "calc2" in "/process/" directory on server B, then I have now on server B : - /process/calc1 - /process/calc2 (and /process/ on server A is empty). How rsync will manage conflict (on server B) if I have another folder like "/process/calc1" in server A after a new calculation (if "/process/calc1" already exist on server B) ? Is it possible to add rules with rsync, and rename "/process/calc1" by "process/calc1R2" in server B ? And so on (ex:calc1R3) ? Thanks.

  Read the article

• Excluding files from web logs

  - by Ray

  I originally tried this question on StackOverflow, but it was suggested that serverfault was a better choice. So, here it is... Looking through my web logs, I see a lot of entries that don't interest me. Some of them are commonly used images, css files, and scripts, which I can easily exclude by un-checking the 'log visits' check box in IIS for the folder properties. I would also like to exclude log entries for certain common requests which are not in their own folders. Mostly, 'favicon.ico'. 'scriptresource.axd', and 'webresource.axd'. These (especially scriptresource.axd) make up almost a third of a typical log file on my site. So, the question is, how do I tell IIS not to log these requests? And is there any reason that this is a bad idea? The purpose of doing this is to reduce the log file size and the amount of work the server has to do, to make the log file more manageable when I need to dig in to them for troubleshooting, and for my own curiosity. I realize that log file parsers can skip the junk, but I am interested in reducing the raw files, before parsing.

  Read the article

• Ubuntu 12.04 suddenly cannot connect to WPA2/WPA Personal protected connection. Windows 7 can

  - by d4ryl3

  I have a laptop with Windows 7 and Ubuntu 12.04. I have a Cisco E1200 and when I set it up, it created 2 SSIDs. Let's name them: MyConnection (WPA/WPA2 personal), and MyConnection-Guest (no authentication, guest password entered via web browser). I had no problem connecting to MyConnection before, either in Windows 7 and Ubuntu. But now, I can't access MyConnection on Ubuntu. It just says "connecting..." then disconnects after a while. But I'm able to access the internet (on Ubuntu) when I connect to MyConnection-Guest. MAC filtering is off (even if it's on its MAC address is in the white list). Any idea why I'm unable to connect to MyConnection in Ubuntu? Thanks. Update: My Ubuntu installation can connect to ANY WiFi connection (WPA/WEP/no auth), except for MyConnection. Update2: This is what "The not so easy way" returned: Initializing interface 'eth1' conf '/etc/wpa_supplicant.conf' driver 'default' ctrl_interface 'N/A' bridge 'N/A' Configuration file '/etc/wpa_supplicant.conf' -> '/etc/wpa_supplicant.conf' Reading configuration file '/etc/wpa_supplicant.conf' Priority group 0 id=0 ssid='MyConnection' id=1 ssid='MyConnection' id=2 ssid='MyConnection' id=3 ssid='MyConnection' WEXT: cfg80211-based driver detected SIOCGIWRANGE: WE(compiled)=22 WE(source)=21 enc_capa=0xf capabilities: key_mgmt 0xf enc 0xf flags 0x0 netlink: Operstate: linkmode=1, operstate=5 Own MAC address: xx:xx:xx:xx:xx:xx wpa_driver_wext_set_key: alg=0 key_idx=0 set_tx=0 seq_len=0 key_len=0 wpa_driver_wext_set_key: alg=0 key_idx=1 set_tx=0 seq_len=0 key_len=0 wpa_driver_wext_set_key: alg=0 key_idx=2 set_tx=0 seq_len=0 key_len=0 wpa_driver_wext_set_key: alg=0 key_idx=3 set_tx=0 seq_len=0 key_len=0 wpa_driver_wext_set_key: alg=0 key_idx=4 set_tx=0 seq_len=0 key_len=0 ioctl[SIOCSIWENCODEEXT]: Invalid argument Driver did not support SIOCSIWENCODEEXT wpa_driver_wext_set_key: alg=0 key_idx=5 set_tx=0 seq_len=0 key_len=0 ioctl[SIOCSIWENCODEEXT]: Invalid argument Driver did not support SIOCSIWENCODEEXT wpa_driver_wext_set_countermeasures RSN: flushing PMKID list in the driver Setting scan request: 0 sec 100000 usec WPS: UUID based on MAC address - hexdump(len=16): 16 3b d8 47 9e 24 50 89 96 16 6d 66 35 f3 58 37 EAPOL: SUPP_PAE entering state DISCONNECTED EAPOL: Supplicant port status: Unauthorized EAPOL: KEY_RX entering state NO_KEY_RECEIVE EAPOL: SUPP_BE entering state INITIALIZE EAP: EAP entering state DISABLED EAPOL: Supplicant port status: Unauthorized EAPOL: Supplicant port status: Unauthorized Added interface eth1

  Read the article

• If I partition a drive connected via eSata will it show different partitions when connected via USB?

  - by jeffreypriebe

  I have an odd problem with an external drive. I'm formatting it connected to my laptop prior to connecting it to my router. The HDD enclosure has both an eSata and USB connections. Generally, I connect it via eSata to my laptop. I created my partitions and connected it to the router, but I see partition information that is different than what I created. After chasing leads concerning large HDD size, I mindlessly connected the HDD to my laptop with USB. Lo! I see the same partitions as the router. Attached are screenshots using the same program and the HDD in question. The only difference is the connection. For the first, I connected via eSata and hit "refresh" on the partition program. Then, turned off the HDD, disconnected the eSata cable, and connected via USB. Power and refresh. eSata: reports a total HDD size of 2328 GB, with four partitions (the third being 1.96TB) USB: reports a total HDD size of 280 GB, with three partitions (the third being 279 GB) Any idea why this is happening? It looks like it clearly is an issue of the 4K sector size and not playing nice with the USB enclosure. I tried it eSata and USB in Windows and Linux and it appears consistently that eSata is reporting correctly, USB incorrectly.

  Read the article

• Feasibility of Windows Server 2008 DFS replication over WAN link

  - by CesarGon

  We have just set up a WAN link that connects two buildings in our organisation. The link is provided by a 100-Mbps point to point line. We have a Windows Server 2008 R2 domain controller on each side of the link. Now we are planning to set up DFS for file services across the organisation. The estimated data volume is over 2 TB, and will grow at approximately 20% annually. My idea is to set up a file server in each building and install DFS so that all the contents stay replicated over the 100-Mbps link. I hope that this will ensure that any user will be directed to the closest (and fastest) server when requesting a file from the DFS folders. My concern is whether a 100-Mbps WAN link is good enough to guarantee DFS replication. I've no experience with DFS, so any solid advice is welcome. The line is reliable (i.e. it doesn't crash often) and our data transfer tests show that a 5 MB/sec transfer rate is easily achieved. This is approximately 40% of the nominal bandwidth. I am also concerned about the latency. I mean, how long will users need to wait to see one change on one side of the link after the change has been made on the other side. My questions are: Is this link between networks a reliable infrastructure on which to set up DFS replication? What latency times would be typical (seconds, minutes, hours, days)? Would you recommend that we go for DFS in this scenario, or is there a better alternative? Many thanks.

  Read the article

• Motion - takes snapshot without motion detected

  - by Emmanuel Brunet

  I've been installed the standard motion 3.2.12 package on debian 7.5. I would like to get snapshot ONLY when motion is detected, but it still saves a picture every second without any activity in front of the camera. I'm using a TENVIS JPT3815W IP camera motion.conf here is my configuration file setup_mode off target_dir /media/videos/log/webcam netcam_url http://webcam/snapshot.cgi netcam_tolerant_check on netcam_userpass admin:alpha1237 # Output frames at 1 fps when no motion is detected and increase to the # rate given by webcam_maxrate when motion is detected (default: off) webcam_motion off output_all off # detection settings 1-255 default 32 noise_level 50 # Maximum framerate for webcam streams (default: 1) webcam_maxrate 25 pre_capture 0 framerate 25 gap 30 locate on mail [email protected] text_right "FRONT CAMERA %Y/%m/%d - %T" text_double on ffmpeg_cap_new on ffmpeg_cap_motion on ffmpeg_video_codec mpeg4 output_motion off snapshot_interval 0 # Quality of the jpeg (in percent) images produced (default: 50) quality 90 # Restrict webcam connections to localhost only (default: on) webcam_localhost off # Limits the number of images per connection (default: 0 = unlimited) # Number can be defined by multiplying actual webcam rate by desired number of seconds # Actual webcam rate is the smallest of the numbers framerate and webcam_maxrate webcam_limit 0 Issue when I start motion images are stored in /media/videos/log/webcam nearly every second. I hjust want to get images when a motion is detected and the according video clip Any idea where the configuration fails ?

  Read the article

• SMTP server closes connection unexpectedly

  - by janin

  I'm writing a python program to send emails, and when trying to send to yopmail, hotmail and some other hosts the connection gets closed by the server without a message. I tried connecting directly with netcat and the same thing happens. Here's what the exchange looks like : $ nc smtp.yopmail.com 25 220 mx.yopmail.com ESMTP *** ehlo mx.myhost.com 250 SIZE 2048000 mail FROM:<[email protected]> 250 OK rcpt TO:<[email protected]> The connection is just closed abruptly at this point. On other hosts, like my ISP's, everything goes fine. I've checked the blacklists but my IP is not listed. Any idea what's going on? Edit: My IP is not listed in any blacklist. I own myhost.com, but I don't have an SPF record. I'll add one and update this post when the record has propagated. Edit 2: with the SPF added the email is now accepted and Hotmail adds a Authentication-Results: hotmail.com; sender-id=pass header to the email. However it gets classified as spam, but I guess that's another matter. Thanks for your help.

  Read the article

• "Server Unavailable" and removed permissions on .NET sites after Windows Update

  - by tags2k

  Our company has five almost identical Windows 2003 servers with the same host, and all but one performed an automatic Windows Update last night without issue. The one that had problems, of course, was the one which hosts the majority of our sites. What the update appeared to do was cause the NETWORK user to stop having access to the .NET Framework 2.0 files, as the event log was complaining about not being able to open System.Web. This resulted in every .NET site on the server returning "Server Unavailable" as the App Domains failed to be initialise. I ran aspnet_regiis which didn't appear to fix the problem, so I ran FileMon which revealed that nobody but the Administrators group had access to any files in any of the website folders! After resetting the permissions, things appear to be fine. I was wondering if anyone had an idea of what could have caused this to go wrong? As I say, the four other servers updated without a problem. Are there any known issues involved with any of the following updates? My major suspect at the moment is the 3.5 update as all of the sites on the server are running in 3.5. Windows Server 2003 Update Rollup for ActiveX Killbits for Windows Server 2003 (KB960715) Windows Server 2003 Security Update for Internet Explorer 7 for Windows Server 2003 (KB960714) Windows Server 2003 Microsoft .NET Framework 3.5 Family Update (KB959209) x86 Windows Server 2003 Security Update for Windows Server 2003 (KB958687) Thanks for any light you can shed on this.

  Read the article

• Why does MOSS sometimes delete an existing user from a site?

  - by Jesse

  I'm experiencing an issue with a MOSS installation. I am using the Site Settings Permissions to add an Active Directory account as a valid user of a site. This entails validating that the user account name is correct via the 'Check Names' button, then giving them 'Contribute' permissions. Once this is done they appear as a user on the 'All People' page. This works fine and the user is able to access the site. At some point in the future (sometimes several days later) the user account is somehow removed as a valid user from the site. This site resides in a test environment so access is pretty well controlled; which has allowed us to rule out someone else going in and removing the user manually. This appears to be something that is being done by the system itself and we have no idea why. We can manually add the user back, but then it will eventually get removed again later. I have an admittedly limited understanding of SharePoint permissions, but I believe that SharePoint stores valid users in a SQL database and I would assume that when dealing with Active Directory accounts it would be storing the user name and probably the SID. It appears that for some reason this record is later getting deleted out of the database, as the users will suddenly disappear from the "All People" page and will start getting "Access Denied: You are not authorized..." messages when trying to access the site. Has anyone seen this behavior before?

  Read the article

• SQL Server 2008 Bring Database Online trying to open a file from a drive that doesn't exist

  - by Nai

  This is my error I am facing TITLE: Microsoft.SqlServer.Smo Set offline failed for Database 'Go3D_Retailer ------------------------------ ADDITIONAL INFORMATION: An exception occurred while executing a Transact-SQL statement or batch. (Microsoft.SqlServer.ConnectionInfo) Unable to open the physical file "E:\Program Files\Microsoft SQL Server\MSSQL10.MSSQLSERVER\MSSQL\DATA\ftrow_Go3D_catalog.ndf". Operating system error 2: "2(failed to retrieve text for this error. Reason: 15105)". Database 'Go3D_Retailer' cannot be opened due to inaccessible files or insufficient memory or disk space. See the SQL Server errorlog for details. ALTER DATABASE statement failed. (Microsoft SQL Server, Error: 5120) Background to this error I've been trying to move my destination logshipping database to another physical server for analysis purposes. Because I do not have domain keys and active directory set up, I had to hack my process by using the same username/password for both the source and destination servers to get the process to work. Following that, I used this guy's solution to move the destination database to another server. However, this error occurs when I try to bring the database back online. I don't have an E drive on my server and I have no idea why it's trying to open a file from E drive. I have over a 100gb left on my hard disk so it's definitely not a space issue. This sounds like a bug... Any ideas?

  Read the article

< Previous Page | 586 587 588 589 590 591 592 593 594 595 596 597  | Next Page >