Search Results

Search found 28441 results on 1138 pages for 'ubuntu lts'.

Page 592/1138 | < Previous Page | 588 589 590 591 592 593 594 595 596 597 598 599  | Next Page >

  • Crackling sound from microphone recently, in 13.04

    - by Patrig Droumaguet
    I use 13.04 since the release and I use Skype which was working well. But recently I've had remarks saying my voice was "crackling", even if the voice from my interlocutor was perfect. Making a test with Audacity and Cheese, I've seen that every recorded sound (with the front microphone of my laptop or a jack microphone) was crackling. It's not really like saturating, the sound has a lot of annoying pops. I've tried to check the settings, they were still on PulseAudio. I've even tried the extreme solution : re-installing Ubuntu (because initially it was working)… with the same problem. If I boot on Windows (dual-boot) I have no problem (so it's not physical). If anyone could help :) My laptop is a HP dv6-6165sf. The sound card is a "IDT 92HD81B1X5" (with BeatsAudio). Thanks a lot ! New tests - july 6th Hi again, I've tried editing /etc/pulse/default.pa with these three settings : load-module module-udev-detect use_ucm=0 tsched=0 load-module module-udev-detect tsched=0 load-module module-udev-detect use_ucm=0 The three of them don't change anything, except the last one (which was by default) which makes Audacity record without any crackling sound. But in Skype, Cheese and Kazam, the sound is crackling… I've installed again Ubuntu 13.04 (from scratch, deleting everything from /home), and I've updated it. The microphone is still cracking. Thanks for your help !

    Read the article

  • Keyboard and mouse/touchpad wont work in 11.10

    - by Maynard
    I installed Ubuntu 11.10 onto my Fujitsu Lifebook N5010 Laptop yesterday and all seemed good up until this morning. My key board and mouse/touchpad no longer work. I can, however, plug in a usb mouse and that works so I am able to shut the laptop off. With the usb mouse plugged in I still can't use the keyboard so the only thing the mouse is good for is shutting the system down. When I first boot the system the mouse/touchpad and keyboard will work long enough so that I can log in my password but then after about 20 seconds or so the mouse/touchpad and keyboard stop working. I have searched the internet for answers and haven't found anything that is working for me. Someone suggested I type a particular command into the terminal but not real sure how I do that without a keyboard. And going out to buy a usb keyboard (assuming that would work) and usb mouse still doesn't fix the problem. Anybody have any suggestions I would REALLY appreciate it. I love Ubuntu but this is just not good.

    Read the article

  • How to Install Broadcom Wireless Drivers (BCM43xx)

    - by Fer1805
    I'm having serious problems installing the Broadcom drivers for Ubuntu. It worked perfectly on my previous version, but now, it is impossible. I'm a user with no advance knowledge in Linux, so I would need clear explanations on make, compile, etc. Edit: For the command: "lspci | grep Network", I get the following message: 06:00.0 Network controller: Broadcom Corporation BCM4311 802.11b/g WLAN (rev 01) For the command: iwconfig, i get the following: lo no wireless extensions. eth0 no wireless extensions. When i follow the following steps (from the above link), there are a NO error message at all: open the 'Synaptic Package Manager' and search for bcm uninstall the bcm-kernel-source package make sure that the firmware-b43-installer and the b43-fwcutter packages are installed type into terminal: cat /etc/modprobe.d/* | egrep '8180|acx|at76|ath|b43|bcm|CX|eth|ipw|irmware|isl|lbtf|orinoco|ndiswrapper|NPE|p54|prism|rtl|rt2|rt3|rt6|rt7|witch|wl' (you may want to copy this) and see if the term blacklist bcm43xx is there if it is, type cd /etc/modprobe.d/ and then sudo gedit blacklist.conf put a # in front of the line: blacklist bcm43xx then save the file (I was getting error messages in the terminal about not being able to save, but it actually did save properly). reboot 'End of procedure' Before (not ubuntu 11.04), if i wanted to connect wireles, i just went to the icon at the upper side of the screen, click, showed ALL the wireless network available, and done. Now, the only options i see are: Wired Network Auto Eth0 Disconnect VPN Enable networking Connection information Edit connection. lspci -vnn | grep Network showed: Broadcom Corporation BCM4322 802.11a/b/g/n Wireless LAN Controller [14e4:432b] hope above info is enough for your help.

    Read the article

  • How do I uninstall the TuxOnIce kernel in 12.04?

    - by Lluis
    I recently installed tuxonice on a Toshiba z830. I have ubuntu 12.04 (kernel was: 3.2.0-26) I wanted to be able to hibernate, which I consider to be a basic thing a OS should allow you to do. Well, it didn't work...but they already tell you it may not so I removed it. For doing all these I followed: Problem with Hibernation After uninstalling I switched off the laptop and after this I started to have several problems. The first one was that Cisco VPN didn't work anymore and then I realised that I could not even suspend my laptop. I found very strange that after removing tuxonice I still had this: /lib/modules/3.2.0-26-generic-tuxonice/ The VPN problem could be solved by just copying from my previous kernel: 3.2.0-26-generic/CiscoVPN/ into the tuxonice one. Not very elegant but works. Now, for the suspend problem (and the previous too) I can hold Shift when starting and select my old kernel and then suspend works again. In my opinion tuxonice was not correctly uninstalled as it left that kernel behind and worse: ubuntu uses it if I do not take action. I have these work arounds....and here is my question: how can I delete this tuxonice kernel safely? If you need more info please let me know.

    Read the article

  • Downclock CPU reaching critical temperature

    - by Draga
    I have an HP tx1250 laptop. It always had serious overheating problems and although usually it runs fine I'm now running a continuous test for my dissertation, this brings the CPU temp close to the critical and from time to time the computer shutdown for reaching it (checked the log). I use to have the same problem on Win XP but I noticed Win Vista and 7 downclock the CPU when is necessary to cool it down so I was thinking if the same is possible on Ubuntu 12. The only program I've found that may do the job is computer temp ( http://computertemp.berlios.de/ ) but it doesn't seems to work under Ubuntu 12. The inside of the laptop is fairly clean, the thermal paste is quite recent, I'm keeping it lifted from the desk and judjung by the sound of the fan that's running fine as well. The pc in now running between 78 and 91 degrees C but about once a day it shut down for reaching 95. I need the results of the test it's running pretty soon so it's important that it runs non-stop. I've though to set the maximum clock of the CPU to slightly less the maximum but then these tests I'm running would take much more time. Thanks! PS: first and last HP laptop for me.

    Read the article

  • Kubuntu 11.10 Lot of Networking problems

    - by Cobraone
    Since I upgrade to 11.10 I have a lot of problems with KDE. First of all there are problems in configuring a static IP address. Just to explain @home I have a normal fiber ADSL and I use a DHCP. When I go to a customer I must insert a static IP address. With ifconfig everything seems ok but there is something wrong in searching DNS names. (I have installed Ubuntu and was going ok again). Now I Have reinstalled again Kubuntu 11.10 and I have the same problem in addition today I have discovered that if I connect to a network in another customer office the desktop freezes and I could only switch between windows with alt+tab. No FN key or right click to open run command works. So i unplugged network (configuration is just DHCP here) and tried on another position in office. It was the same. My Laptop freezes when connected, a fedora 14 of a friend works. So I decided to connect my Galaxy S II as USB network device. Everything is ok for like 3 minutes. When I noticed a little loss of signal again the desktop freezes and i must work (like now) just switching between windows with alt+tab). Additional information: Unplugging network or restarting it via Konsole does not not solve the freezing problem. Every time I must open a console and reboot. Any idea of what tests to do ? Just a recommendation: If I must post here logs or something else please guide me. I use Linux since Ubuntu 9 but I am not an "expert".

    Read the article

  • Can't access computer

    - by Pudica
    I'm running Ubuntu 14.04 on an Intel NUC and it won't boot! The last successful boot was earlier today but now each time I try it gets stuck on the Grub menu where it prompts for memory check etc. This is not a dual boot system, so this screen shouldn't ever appear, and it never has before. It's GRUB version 2.02~beta2-9, which is a little disconcerting, as I'm on the stable sources. Unfortunately the keyboard (I've tried 2 keyboards just in case) is not responding at this point in the boot process, so I can't select the "Ubuntu" menu option in Grub. The keyboard works during the bios stage, so I can configure it to boot from USB, and I tried a flash drive with 14.04 on it. The flash drive works in my laptop but is completely ignored by the NUC (I tried all 3 USB ports!). It seems that I have no way of getting into the machine at all! The Intel support site was my first option, but the site is down. I expect it's a long shot, but if anyone has any ideas I'd be very grateful.

    Read the article

  • How to modify partitions after install?

    - by ChocoDeveloper
    I wanted to have Ubuntu with full disk encryption on one big partition, and Windows on a small one. In 12.04, only the Server Edition installer has full disk encryption, so I used that and then installed ubuntu-desktop. When it asked for the size, I reduced it from ~999GB to ~750gb. Now after the install, on both gparted and disk utility I see /dev/sda2 taking ~931GB, and nothing unallocated, so I can't create a partition for windows. I got the size right, because when I right-click inside a folder, then hit 'properties', I see Free space: ~690GB (I don't know why it's not ~750GB, but at least it's not 900). The command df -h shows the same. So what can I do? Normally I would just resize a partition with gparted to create unallocated space, then create the partition. But here I have two problems: gparted does not seem to be showing the correct values, and also it says it does not support LUKS so I'm afraid it will mess things up. Any thoughts?

    Read the article

  • Grub can not boot after resizing windows XP (NTFS) partition. What is to be done? [closed]

    - by cipricus
    Possible Duplicate: How to Repair Grub while dual booting ( win7 / ubuntu 11.10) I had installed Lubuntu on a PC with Windows XP and used dual boot for some time with no problems. Since I had almost abandoned Windows (kept it for printing...) I decided to resize its ntfs partition and add the free space to my Ubuntu space. Tried that with a gparted stick and a live cd but would not work due to an issue related to the ntfs partition: gparted signaled with a red exclamation point that there was a problem with that partition. I read that a checkdisk might solve it but in the end used EaseUS in Windows to shrink (resize) the ntfs partition and create a new one (ext3) from the space left. All seemed ok with that procedure: but resizing the partition and moving the data might have affected the grub file: or whatever the following message means, which I get when trying to start my pc: error: file not found grub rescue> Booting from a live cd I see, beside the shrinked windows partition and my old linux one, the newly created partition, containing a directory called lost+found that I cannot open. Can I fix the grub file and recover both my XP and Lubuntu installations?

    Read the article

  • PS2 Eyetoy Recording Quality

    - by Fire
    I have Ubuntu 12.04 LTS and a PS2 eyetoy "Namtai". Don't worry - this is not the sterotypical " how do I get my eyetoy working" question. My eyetoy works fine on Cheese, gucview and various other media software like VLC. However, It seems like I am capped by 25fps. If I recall, the eyetoy is much better than this (~60fps) but cannot find any way to fix this. The best program that I have have found is VLC because its advanced options allow you to change many settings but the framerate setting appears to have no effect. What software or settings can I use to take full advantage of my eyetoy? To give you the full information I wish to attach multiple eyetoys to the system and record from all of them. (Security software like motion and zoneminder, I couldn't get installed correctly on my system- so I haven't tried those yet). edit - I tried the same camera on a Windows system and the frame rate is much better in VLC compared to the Ubuntu system. Mind you with default settings in Windows VLC, the resolution isn't great. However, in Skype for example the resolution is amazing and the framerate is good. It seems there must be some settings I am missing somewhere because it doesn't appear to be a hardware problem...

    Read the article

  • NFS mount of /var/www to OS X

    - by ploughguy
    I have spent 2 hours trying to create an NFS mount from my Ubuntu 10.04 LTS server to my OS X desktop system. Objective: three way file compare between the code base on the Mac, the development system on the local Linux test system, and the hosted website. The hosted service uses cpanel so I can mount a webdisk - easy as pie - took 10 seconds. The local Ubuntu box, on the other hand - nothing but pain and frustration. Here is what I have tried: In File Browser, navigate to /var/www/site and right-click. Select share this folder. Enter sharename wwwsite and a comment. Click button "Create Share". Message says - you can only share file systems you own. There is a message on how to fix this, but the killer is that this is sharing by SMB. It will change the LFs to CR-LFs which will affect the file comparison. So forget this option. In a terminal window, run shares-admin (I have not been able to convince it to give me the "Shared Folders" option in the System Administration window - Maybe it is somewhere else in the menu, but I cannot find it) define an NFS export. Enter the path /var/www/site, select NFS enter the ip address of the iMac and save. On the mac, try to mount the file system using the usual methods - finder, command line "mount" command - not found. Nothing. Tried restarting the linux box in case there is a daemon that needs restarting - nothing. So I have run out of stuff to do. I have tried searching the documentation - it is pretty basic. The man page documentation is as opaque as ever. Please, oh please, will someone help me to get this @38&@^# thing to work! Thanks for reading this far... PG.

    Read the article

  • Grub2 mutual dependency issue

    - by A T
    For various reasons I am installing .deb dependencies for grub2 using dpkg directly (rather than apt-get). root@ubuntu:/dl# dpkg -i grub-gfxpayload-lists_0.6_amd64.deb Selecting previously unselected package grub-gfxpayload-lists. (Reading database ... 249808 files and directories currently installed.) Preparing to unpack grub-gfxpayload-lists_0.6_amd64.deb ... Unpacking grub-gfxpayload-lists (0.6) ... dpkg: dependency problems prevent configuration of grub-gfxpayload-lists: grub-gfxpayload-lists depends on grub-pc (>= 1.99~20101210-1ubuntu2); however: Package grub-pc is not configured yet. dpkg: error processing package grub-gfxpayload-lists (--install): dependency problems - leaving unconfigured Processing triggers for man-db (2.6.7.1-1) ... Errors were encountered while processing: grub-gfxpayload-lists By configure I assume it means install+configure, so I tried: root@ubuntu:/dl# dpkg -i grub-pc_2.02~beta2-9_amd64.deb (Reading database ... 249818 files and directories currently installed.) Preparing to unpack grub-pc_2.02~beta2-9_amd64.deb ... Unpacking grub-pc (2.02~beta2-9) over (2.02~beta2-9) ... dpkg: dependency problems prevent configuration of grub-pc: grub-pc depends on grub2-common (= 2.02~beta2-9); however: Package grub2-common is not installed. grub-pc depends on grub-pc-bin (= 2.02~beta2-9); however: Package grub-pc-bin is not installed. grub-pc depends on grub-gfxpayload-lists; however: Package grub-gfxpayload-lists is not configured yet. dpkg: error processing package grub-pc (--install): dependency problems - leaving unconfigured Processing triggers for man-db (2.6.7.1-1) ... Errors were encountered while processing: grub-pc How do I solve this problem?

    Read the article

  • Installation on SSD with Windows preinstalled

    - by ebbot
    I bought a laptop with this fancy SSD drive, fancy new UEFI aso. I figured at first Windows out Ubuntu in but after doing 3 DoA on 3 laptops in one day I realized that maybe keeping Windows could come in handy. So dual boot it is. And this is what I've got: Disk 1 - 500 Gb HD 300 Mb Windoze only says "Healthy" don't know what it's for. 600 Mb "Healthy (EFI partition)" 186.30 Gb NTFS "OS (C:)" "Healthy (Boot, Page File, Crash Dump, Primary Partition)" 258.45 Gb NTFS "Data (D:)" "Healthy" 20.00 Gb "Healthy (Recovery Partition)" Disk 2 - 24 Gb SSD 4.00 Gb "Healthy (OEM Partition)" 18.36 Gb "Healthy (Primary Partition)" So I'm not sure what the first partition on each drive does (the 300 Gb on the HD and the OEM Partition on the SSD. Nor do I know what Data (D:). I think the 2nd partition on the SSD is for some speedup of Windoze. I'm debating if I should shrink the OS (C:) drive to around 120 GB or so. Clear the Data (D:) and also use the whole SSD for Ubuntu. That would leave me 24 Gb for e.g. / on the SSD and some 320 Gb on the HD for /home and swap. Is this a reasonable setup? Do I need to configure fstab for the SSD differently to a HD?

    Read the article

  • "Unmet Dependencies" problem when trying apt-get install

    - by GChorn
    Anytime I try to install python packages using the command: sudo apt-get install python-package I get the following output: Reading package lists... Done Building dependency tree Reading state information... Done You might want to run 'apt-get -f install' to correct these: The following packages have unmet dependencies: linux-headers-generic : Depends: linux-headers-3.2.0-36-generic but it is not going to be installed linux-headers-generic-pae : Depends: linux-headers-3.2.0-36-generic-pae but it is not going to be installed linux-image-generic : Depends: linux-image-3.2.0-36-generic but it is not going to be installed E: Unmet dependencies. Try 'apt-get -f install' with no packages (or specify a solution). This seems to have started when these same three packages showed up in Ubuntu's Update Manager and kicked an error when I tried to install them there. Based on the suggestion in the output above, I tried running: sudo apt-get -f install But this only gave me several instances of the following error: dpkg: error processing /var/cache/apt/archives/linux-image-3.2.0-36-generic_3.2.0-36.57_i386.deb (--unpack): unable to create `/lib/modules/3.2.0-36-generic/kernel/drivers/net/wireless/ath/carl9170/carl9170.ko.dpkg-new' (while processing `./lib/modules/3.2.0-36-generic/kernel/drivers/net/wireless/ath/carl9170/carl9170.ko'): No space left on device Now maybe I'm way off-base here, but I'm wondering if the error could be coming from the "No space left on device" part? The thing is, I'm running Ubuntu as a VirtualBox VM but I've got it set to dynamically increase its virtual hard drive space as needed, so why am I still getting this error? Here's my output when I use dh -f: Filesystem Size Used Avail Use% Mounted on /dev/sda1 6.9G 5.7G 869M 88% / udev 494M 4.0K 494M 1% /dev tmpfs 201M 784K 200M 1% /run none 5.0M 0 5.0M 0% /run/lock none 501M 76K 501M 1% /run/shm VB_Shared_Folder 466G 271G 195G 59% /media/sf_VB_Shared_Folder When I perform sudo apt-get -f install and the system says, After this operation, 192 MB of additional disk space will be used. Does that mean 192 MB of my virtual machine's current memory, or 192 MB on top of the rest of my free space? As I said, my machine normally dynamically allocates additional memory from the host machine, so I don't see why there would be memory restrictions at all...

    Read the article

  • Installing nVidia drivers for Quadro FX 880M on 10.10 caused shutdown/startup issues.

    - by Chantz
    So I was facing weird graphics drivers issues due to the default nouveau drivers that came installed with Ubuntu 10.10 hence I installed the latest nVidia graphics drivers & I the weird graphics issues stopped happening. So far so good, but when I tried to shut down the laptop it got stuck at the window with text 15, shutting down... modem-manager: Caught signal 15, shutting down... init: Disconnected from system us init: dbus main process (1107) killed by TERM signal And this happens .everytime.without.fail. I tried updating the kernel and any/all drivers through update manager but it stil happens. Not only this even the startup screen is totally screwed up. It just displays Ubuntu 10.10 in text with 3 dots. But that is acceptable. To power cycle down the laptop each and everytime for shutdown is not cool. Same goes for when I try to restart. Interesting thing is if I try to shutdown the laptop when I am on the login screen it does so without any problems. I googled & many people seem to face the same issue but I couldn't find any silver bullet hoping to find one here.

    Read the article

  • Is my graphics card in use or not?

    - by Lindhe94
    I have a Samsung Series 7 NP730U3E which is running Ubuntu Gnome 13.10. This computer have an Intel Core i5 3337U an AMD Radeon HD 8570M on the inside. Ubuntu 13.10 is said to have driver support for this graphics card, but I am not sure whether or not this is the case. When I check System Settings Details it says "Graphics: Intel® Ivybridge Mobile" and lspci | grep VGA returns VGA compatible controller: Intel Corporation 3rd Gen Core processor Graphics Controller (rev 09). But lshw -c video returns *-display description: Display controller product: Mars [Radeon HD 8730M] vendor: Advanced Micro Devices, Inc. [AMD/ATI] physical id: 0 bus info: pci@0000:01:00.0 version: 00 width: 64 bits clock: 33MHz capabilities: pm pciexpress msi bus_master cap_list rom configuration: driver=radeon latency=0 resources: irq:47 memory:e0000000-efffffff memory:f7e00000-f7e3ffff ioport:e000(size=256) memory:f7e40000-f7e5ffff *-display description: VGA compatible controller product: 3rd Gen Core processor Graphics Controller vendor: Intel Corporation physical id: 2 bus info: pci@0000:00:02.0 version: 09 width: 64 bits clock: 33MHz capabilities: msi pm vga_controller bus_master cap_list rom configuration: driver=i915 latency=0 resources: irq:46 memory:f7800000-f7bfffff memory:d0000000-dfffffff ioport:f000(size=64) What is the case? Is my graphics card is use, or do my laptop have undiscovered powers yet to yield?

    Read the article

  • Having trouble installing Bradcom STA driver

    - by user192881
    I just installed Ubuntu and love it so much, its so fast now. But I have a problem connecting to the internet. I checked and saw I have to install the driver Broadcom STA wireless driver but every time I do try to install it it says: Sorry, installation of this driver failed. Please have a look at the log files for details: /var/log/jockey.log I went to the terminal and copy and pasted the log file name. and when I did it, it said I have no permission to access this file. I checked on the forums that I have to be on a wired connection. So I plugged my laptop into my router and I got internet then tried to install the driver again. And it was loading then when it got to the end the same message popped up. Also I have one of those little USB router things you plug into the computer and it gives you internet I have been using that but its to slow. So I want to use the one in my computer but cant. Also I tried the command: sudo modprobe wl and when i type that command in it says: FATAL: Module wl not found Also I'm using Ubuntu 12.04

    Read the article

  • Is text-only mode a saving or a problem for battery savings?

    - by Robottinosino
    A friend is flying to the US from Europe and asked me a very thought-provoking question, which I am not remotely able to answer with substance so I am asking it here: How to absolutely maximise battery life on an Ubuntu (laptop) install? do not rush to mark this as duplicate, there is an important point here: does -GNOME- help or worsen battery life? Let me provide some context: The only task he needs to perform is: edit text files in Vim. He is unsure whether running GNOME will drain his battery life more or actually save him some battery life given the smarts of GNOME's power management features like "switch this peripheral to -power save- after X minutes..." (GNOME might just be a configuration front-end for settings that are governed by command-line utils for all I know?) He could perfectly well boot the system in text-only mode and use the automatic 6 virtual consoles for his needs, if that's a saving at all over running tmux (I think so because of all the smart buffering/history/etc the latter does by default?) Exactly how would you advise him to run his laptop during his flight? What I told him already: power off WiFi in the BIOS, not from the "GUI" power off Bluetooth switch off the courtesy light and use low monitor brightness play music off of his phone, not mp3blaster do not use his tiny portable mouse (and do not attach any other USB gimmicks like "screen light", etc) stop development services he will not be using, especially apache2, tomcat, dovecot, postgresql, etc. Potentially: - switch off his cron jobs? (he does an rsync + tar + 7za of his "work in progress" every so often) I think the above is standard stuff one could get off StackExchange, and with many duplicates... the core of this question is, I think: __ will running Ubuntu in text-only mode be a saving in terms of battery life or a problem? why? (provide some technical arguments) __ I think it will be a saving but I am also scared about "other things" detecting and enabling advanced chipset power management features only when some services are started.. and fear these "services" may be off in text-only mode?

    Read the article

  • Broadcom 4313 doesn't work following 12.04 upgrade

    - by Lucas
    I have an hp G62-228Ca laptop with a BCM4313 previously running Ubuntu 11.10. I ran the 12.04 upgrade last night without much thought. Following the upgrade and mandatory reboot, the wireless card no longer shows up in the network manager, the first time I've had any kind of issues with wireless under Ubuntu. I've done much Googling on the issue but so far I haven't found a permanent solution. Mucking around with some packages though (I've installed five different ones or so), I've managed to devise a workaround that I must run every time I boot the laptop. I have to remove the Broadcom STA driver and reinstall it. Inspiration taken from here: WiFi does not work, Broadcom STA Wireless driver does not work on a BCM4313 After the second modprobe command, the wireless reappears in the network manager and ten seconds after that I'm back on the wifi. If anyone can provide some advice on how to fix this permanently I will be extremely grateful. I'd rather not roll back to 11.10 or reinstall, but I will if I need to. Just let me know if you need the output from any terminal commands. Thanks in advance!

    Read the article

  • No text in working indicator-messages after enabling different icons depending on the status

    - by user106750
    My indicator-messages has some problems. As you can see in the image, there appears no text. The indicator is working correctly, if there is some income, a number will appear in its proper place or I will be able to see the minutes passed after I got an email, but still no information. As you can see in the picture, I changed the envelope icon for the status one. I configured it as is indicated in http://www.omgubuntu.co.uk/2012/08/ubuntu-add-new-message-indicator-icons, with the indicator changing depending on the status. But I modified it so I see the bubble. The bubble gets the arrow when I'm absent, for example, or an "X" of I'm disconnected, and also turns blue if there an income. I believe the problem is related with this new indicator. The first days, it was working fine, but then the text dissapeared. I've tried uninstalling and reinstalling the packet, with no success. I'm using ubuntu 12.10 64bits with Unity. Someone has an idea how to fix this? I would prefer conserving the characteristic of having different icons. Thanks a lot!!! Image here: http://i.stack.imgur.com/Ucgi4.png

    Read the article

  • Touchpad not working after connecting hdmi cable

    - by user286632
    I had installed Ubuntu 14.04 2 weeks back on my new laptop along side Windows 8. 1. And it was working fine. But yesterday after I connected Ubuntu with my TV using the HDMI cable, the cursor/ pointer stopped working. The pointer is not visible and my touchpad is not working. I connected the hdmi cable with youtube in Firefox. But only the wallpaper was visible on the TV. Also the right click menu, alt tab window, etc was also visible. But the side menu and the Firefox window was not visible. The pointer was visible on the tv and the touchpad was working, I was able to move the pointer. After I removed the HDMI cable, my cursor/pointer disappeared and my touchpad is not responding! ! I tried to restart many times, but still no luck. Its still not visible in the desktop. The pointer is visible in the login screen, but is not responding to the touchpad. I tried to login to my KDE session, there too the pointer is visible but is not responding to the touchpad. It is not moving.

    Read the article

  • External monitor on old Dell 700m?

    - by Adam Henne
    Okay, linux noob. I installed 10.04 on an old Dell 700m in hopes of using it as a media center device. That seems to work great, except now it won't output to the external monitor. VGA cable works fine, TV recognizes other computers fine, it's the laptop that won't output. Turns out that the 700m, unlike every other computer out there, doesn't have a Fn hotkey to switch monitors. The only way to do it in Windows was to go through the Control Panel. In Ubuntu, though, the Monitor setup won't detect or recognize any monitors. The laptop display works fine, but I can't adjust or add anything. I did a little research and found suggestions for older Ubuntu builds involving the xorg.conf. I tried one out, in spite of my unfamiliarity, and it's screwed the whole display big time. I can fix that with a clean reinstall, that's no problem, but I'm cautious about editing xorg again. Any suggestions? Thank you!

    Read the article

  • How can I restore my Acer Aspire one GNU version 1.98 to factory settings?

    - by user100380
    Requires keyring and authentication to install and unistall programs or update anything. I just want to restart from scratch so i can clean it up anyways. Can anyone help? Also, on start up a list on a black screen will come up saying Ubuntu with linux version 26.32-40 generic or recovery version and at the bottom of different versions has one Window 7 loader option. When I get into recovery menu to try and restore to factory settings my netbook has no restore option. I've tried pressing alt-f10 and holding alt and repeatedly tap f10 but nothing seems to work, and my acer asks for a password login to even load windows 7 which I don't have. Any ideas? I've looked a lot on the internet for help but I'm getting to my last resort, to get of this thing for once and for all. I want to be able to personalize and add programs as I please, this is all bs to go through to unistall one freaking game or get rid of ubuntu gnome keyring!! Please help!! Thank you. :)

    Read the article

  • Installing Chrome Java Plugin

    - by kyleskool
    I've been trying to install the Java plugin for Chrome for a couple hours now, and I figured it was time to ask people with more experience. I can't seem to get it working. My current Java version is the 64-bit OpenJDK 1.6.0_24. I tried installing the IcedTea plugin to no avail. I have Ubuntu 12.04 64-bit installed at the moment. When I tried testing if java was enabled in Chrome, any website with a Java applet would not load (when I disabled the plugin, they loaded, but not the applet). I followed the instructions from here: http://technonstop.com/install-java-plugin-ubuntu-linux which said to create this script and run it: JAVA_HOME=/usr/lib/jvm/jdk1.7.0 MOZILLA_HOME=~/.mozilla mkdir $MOZILLA_HOME/plugins ln -s $JAVA_HOME/jre/lib/i386/libnpjp2.so $MOZILLA_HOME/plugins Note: You may need to change the value of JAVA_HOME so that it correctly points to your installation of the JDK. 64-bit users will need to change the final line to: ln -s $JAVA_HOME/jre/lib/amd64/libnpjp2.so $MOZILLA_HOME/plugins but this did not work as well. I just test it in Firefox and it's working. Still nothing for Chrome

    Read the article

  • problem in connecting Reliance booadband +

    - by Athira R
    I tried connceting reliance broadband in ubuntu. then an autorun prompt will come. when i click install another pop up coming saying autorun file not found. And when i checked in Internet connection to add connection. Reliance broadband option iteself is not there as connected device. This is Athira. I could not find any add comment option on my main question. So i created a new account and adding as new answer to ur question. athira@athira-laptop:~$ sudo lsusb Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 004: ID 12d1:1505 Huawei Technologies Co., Ltd. Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 002: ID 08ff:1600 AuthenTec, Inc. AES1600 Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 002: ID 0421:0508 Nokia Mobile Phones E65 (PC Suite mode) Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 002: ID 064e:a103 Suyin Corp. Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub athira@athira-laptop:~$ i got this after running it in ubuntu 10.04

    Read the article

< Previous Page | 588 589 590 591 592 593 594 595 596 597 598 599  | Next Page >