Search Results

Search found 17130 results on 686 pages for 'computer lab'.

Page 597/686 | < Previous Page | 593 594 595 596 597 598 599 600 601 602 603 604  | Next Page >

• SATA Windows 7 Problems

  - by Isaacs

  Scenario: Core 2 Duo processor, Gigabyte MB, 4 SATA Western digital 500 GB hard drives, windows 7 64 bit. Problem: Copying data from USB or among SATA hard drives is faulty. When trying to copy 20GB from one HD to another it starts off with normal ~14-15 MB/s transfer rates and eventually bogs down to < 120KB/s transfer rates. If I leave it alone over night I come back with my computer crashed and setting at BIOS detecting hard drives. Troubleshooting: Removed all but 1 HD with OS on it, everything seems to be happy. I can copy large files from USB HD to main/single HD. Ran SpinRite on all hard drives, no errors found. Tried adding one HD to machine and problem exists, tried switching SATA cables, and SATA ports on MB. Reinstalled windows 7 x2 (from different disks..). Oddly enough if I boot to a ubuntu everything works fine. Getting ready to purchase a new MB, but wanted to see if anyone had suggestions. Thanks!

  Read the article

• Cannot access domain from windows 2003 client

  - by Peuge

  Hey all, First off I am a novice at AD and DNS so please bear with me. This is my current situation: I have one server which is a DC and DNS server (win2k3) - Machine 1. I have another machine which is trying to join this domain - Machine2. This machine is also a win2k3 server. This is what I have done so far: I have setup DNS on the DC and its tcp/ip dns is pointing to itself. On machine2 I have set its dns to point to the dc. The DNS has been setup with a forward lookup zone with the same name as the domain (accdirect.com). I can ping machine1 from the machine2 by its FQDN and ip. I have set up forwarders on the DC for our ISP dns and can browse the internet on both machines. In the DNS mmc on the DC I can see a host (A) has been created for machine2. The problem is I still cannot join the domain. When I try join the domain via my computer - properties then it brings up the username/password box and after I go "ok" it says cannot find domain accdirect.com If I run this from machine2 dcdiag /s:accdirect.com /u:accdirect.com\admin /p: then I get the following: Performing initial setup: ** Warning: could not confirm the identity of this server in the directory versus the names returned by DNS servers. If there are problems accessing this directory server then you may need to check that this server is correctly registered with DNS [accdirect.com] Directory Binding Error 1722: Win32 Error 1722 This may limit some of the tests that can be performed. Done gathering initial info. On the dc all dcdiag and netdiag results pass. If anyone could help me I would really appreciate this! Sorry if any of my terminology is a bit off, I have only been doing this for two days. thanks Peuge

  Read the article

• Expanding to dual video cards

  - by Anthony Greco

  I know a lot of factors can go into play here, so I will list my current hardware and setup: MOBO: GIGABYTE GA-890FXA-UD5 [http://www.newegg.com/Product/Product.aspx?Item=N82E16813128441] Processor: AMD Phenom II X6 1090T Black Edition Thuban 3.2GHz [http://www.newegg.com/Product/Product.aspx?Item=N82E16819103849] Ram: G.SKILL Ripjaws Series 16GB (4 x 4GB) [https://secure.newegg.com/NewMyAccount/OrderHistory.aspx?RandomID=4933910872745320111128011418] Current video card: EVGA 01G-P3-1366-TR GeForce GTX 460 SE [http://www.newegg.com/Product/Product.aspx?Item=N82E16814130591] OS: Windows 7 Ultimate x64 Currently I can run 2 monitors just fine in my setup. However, I want to upgrade this to 4 monitors. My question is, what is the best way to do this? I remember in the past reading I need the same type of video card, however would any GeForce GTX work, or do i need that very specific model (EVGA 01G-P3-1366-TR GeForce GTX 460 SE)? Are there any issues I should be aware of before I order 2 new monitors and a video card? Are there video cards better setup for this? I know NVidia offers SLI, however I do not know if my mobo is compliant. My mobo also offers CrossFireX configuration, though from what it says only Radeon are compliant. Any suggestions / feedbacks on my best route with my current setup is appreciated. Even if you suggest buying 2 new identical video cards, as long as you can mention which and why that is better I really appreciate it. Note: I really do not do any gaming. I sometimes do some 3D work in Unity and very rarely in Maya. Besides that I mostly do all my computer work in Visual Studios and Photoshop. I however need the 2 extra monitors because I monitor sometimes 5 remote desktops at once and switching on only 2 is becoming a very big pain. Also seeing 3 side by side while I work on the 4th will be very helpful. Again, I appreciate any feedback, as I have googled a bunch and just want to make sure what I buy will work.

  Read the article

• VPN issue: SSTP Service service started and then stopped

  - by Ampersand

  When I was trying to set up a VPN connect on my laptop running Windows 7 Ultimate, I got this error: Network Connections Cannot load the Remote Access Connection Manager service. Error 711: The operation could not finish because it could not start the Remote Access Connection Manager service in time. Please try the operation again. I traced through some service dependencies and discovered that Secure Socket Tunneling Protocol Service was set to Manual. However, when I try to manually start the service, I get: Services The Secure Socket Tunneling Protocol Service on Local Computer started and then stopped. Some services stop automatically if they are not in use by other services or programs. Setting all the services involved to Automatic did not help. SSTP just showed Automatic and Stopped in the Services panel. I found a solution that involved booting in Safe Mode and deleting the contents of C:\Windows\System32\LogFiles\WMI\RtBackup. This solution worked, and I could set up a vpn connection, but only until I rebooted again. TL;DR I'm looking for a way to permanently enable Secure Socket Tunneling Protocol Service and other vpn-related services permanently so I don't have to reboot into safe mode and delete files every time I need to connect to a vpn.

  Read the article

• Macbook Battery Charging Troubles

  - by bobber205

  Problem: Occasionally, my macbook's battery will say it's charging and actually won't be. It stays at 0% for a long time. Other info: I thought it was my battery (laptop was 3 years old). Got a new battery. Issue did not go away. Got a new power supply. Did not go away. Ended up getting a unibody macbook pro. :) (We even ended up moving to a new house). Now still having the issue. The only thing I can think of is my power strip, which is the only thing that has stayed constant. Is it possible for the strip to be affecting the amount of watts my macbook(s) are getting and preventing it from properly charing the battery. I think it goes in and out, the battery picks up the slack and once it's empty the computer shuts down b/c there's no power at all for a second or two. Funny thing is I have a desktop PC on this same strip and it has never had issues with power. Thanks! :)

  Read the article

• Connecting 2 different subnet masks

  - by Jonathan

  I'm no network genius, but I have managed to get most things running. I get confused about subnets and gateways though. We have an office server connected to around 20 PC's that all communicate fine. We have just gotten a cutting machine that won't connect to our network. The server has DHCP, but that fails on the cutting machine, so I've been trying to set the IP manually. Server details are as follows: IP: 10.1.1.12 SUBNET: 255.255.255.0 GATEWAY: 10.1.1.1 Internet connection is via the modem which is 10.1.1.1 An office PC is ussually set up through DHCP and has the following settings: IP: 10.1.1.36 SUBNET: 255.255.255.0 GATEWAY: 10.1.1.1 PRIMARY DNS: 10.1.1.12 Cutting Machine computer has 2 network ports. 1 is specifically for the communication between the PC and the cutting machine. It's details must be as follows: IP: 10.100.100.2 SUBNET: 255.255.255.252 GATEWAY: BLANK The other network port need to connect to the server. I was told that the IP and SUBNET need to be as follows: IP: 10.100.100.1 SUBNET: 255.255.255.252 GATEWAY: ?? How can I connect this port to the server and/or the internet. If anyone can offer assistance, it would really be appreaciated.

  Read the article

• How can I recover my system after running 'mkfs' on the system partition?

  - by Filip Podgórny

  I am not a Linux user, and was doing some homework, I blindly typed sudo mkfs ext3 dev/sda2 (I had Ubuntu as Windows installation). I've done few more things, and turned Ubuntu off to switch on Windows back. No operating system installed - this is the message I'm getting. I plugged my HDD onto another computer and all my files are still there. What should I do to get my windows installation back? df -l (before mkfs) /dev/loop0 29G 2,0G 27G 8% / udev 3,0G 4,0K 3,0G 1% /dev tmpfs 1,2G 900K 1,2G 1% /run none 5,0M 0 5,0M 0% /run/lock none 3,0G 1,3M 3,0G 1% /run/shm /dev/sda3 455G 123G 333G 27% /host /dev/sdb1 1,9G 820M 1,1G 43% /media/PHONE CARD mkfs output (polish, sorry) mke2fs 1.41.14 (22-Dec-2010) Etykieta systemu plików= Typ OS: Linux Rozmiar bloku=1024 (log=0) Rozmiar fragmentu=1024 (log=0) Stride=0 bloków, szerokosc Stripe=0 bloków 25688 i-wezlów, 102400 bloków 5120 bloków (5.00%) zarezerwowanych dla superuzytkownika Pierwszy blok danych=1 Maksymalna liczba bloków systemu plików=67371008 13 grup bloków 8192 bloków w grupie, 8192 fragmentów w grupie 1976 i-wezlów w grupie Kopie zapasowe superbloku zapisane w blokach: 8193, 24577, 40961, 57345, 73729 Zapis tablicy i-wezlów: zakonczono Tworzenie kroniki (4096 bloków): wykonano Zapis superbloków i podsumowania systemu plików: wykonano Ten system plików bedzie automatycznie sprawdzany co kazde 30 montowan lub co 180 dni, zaleznie co nastapi pierwsze. Mozna to zmienic poprzez tune2fs -c lub -i.

  Read the article

• Black Screen on Logon (windows 7 home premium)

  - by Blacknight334

  i have been having some trouble with a dell Xps 15 laptop that i recently purchased. it is under a month old, and a problem has occurred, upon logging on just after start up, the computer will just sit on a black log on screen (with the mouse still visible and active) for a few minutes. it is extremely annoying, especially when im in a rush. the laptop is under a month old. So far, i have tried to update the drivers, all windows update, and still, nothing. also, it doesnt seem to do it when i log into safe mode, or if it does, it will do it for less than 10 seconds, then load the desktop (in normal boot, it usually takes a few minutes). i have also run a number of the inbuilt diagnostics, but found no errors. i want to avoid having to do a system restore for as long as i can. does anyone know anything that can help? (the laptop is running a 500gb SSD, 2gb Nvidia 640m, 8gb ram, 3rd gen i7 quad core with 8 threads) thanks.

  Read the article

• Redirect local, not internal, requests using SuSEfirewall2 or an iptables rule

  - by James

  I have a server that is running a web application deployed on Tomcat and is sitting in a test network. We're running SuSE 11 sp1 and have some redirection rules for incoming requests. For example we don't bind port 80 in Tomcat's server.xml file, instead we listen on port 9600 and have a configuration line in SuSEfirewall2 to redirect port 80 to 9640. This is because Tomcat doesn't run as root and can't open up port 80. My web application needs to be able to make requests to port 80 since that is the port it will be using when deployed. What rule can I add so that local requests get redirected by iptables? I tried looking at this question: How do I redirect one port to another on a local computer using iptables? but suggestions there didn't seem to help me. I tried running tcpdump on eth0 and then connecting to my local IP address (not 127.0.0.1, but the actual address) but I didn't see any activity. I did see activity if I connected from an external machine. Then I ran tcmpdump on lo, again tried to connect and this time I saw activity. So this leads me to believe that any requests made to my own IP address locally aren't getting handled by iptables. Just for reference he's what my NAT table looks like now: Chain PREROUTING (policy ACCEPT) target prot opt source destination REDIRECT tcp -- anywhere anywhere tcp dpt:http redir ports 9640 REDIRECT tcp -- anywhere anywhere tcp dpt:xfer redir ports 9640 REDIRECT tcp -- anywhere anywhere tcp dpt:https redir ports 8443 Chain POSTROUTING (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination

  Read the article

• Epson Artisan 800 on Ubuntu/Linux

  - by Tim Lytle

  Update for Ubuntu 10.04: Printing should work 'out-of-box', scanning still needs the newer sane backend. Looking for a known good way to setup an Epson Artisan 800 on Ubuntu specifically or any linux box in general. It is a printer/scanner with ethernet/wifi/usb. I'd like to use it as a network printer/scanner being able to do both from my Windows and Ubuntu machines; however, if it needs to be physically connected to a computer (preferably the Ubuntu machine) that is doable (again, then sharing print/scan functions to the network). Basically, I'm looking for someone who has used this printer/scanner (or similar) in a multi-platform environment to share how the set it up and how well it worked. Updated: A little more information, like most printers (I expect) the documentation for the printer basically says, "don't use plug-n-play, run our setup CD from your Windows/Mac system", to do anything (set it up for network use even). I guess that's to make it easy for anyone else to setup, but when you're looking to use it with an unsupported (by Epson's documentation) OS, you're just stuck on your own. What I was hoping for was someone who could say, "Forget the bundled software, do [this] to set it up on wifi manually, install [this] to connect to the scanner from [os], printing works with [this] driver - at least that's how I set it up." I'll will (and have so far) use the information here, and post my own setup when I'm done, if there's no one else out there with that experience.

  Read the article

• Getting old bluetooth headset out of standby on Windows 7

  - by luagh45

  I think this is the problem, and if not, I'm open to suggestions. I have an old Jabra BT200 that I used to use on my phone. When a phone call was coming in it would beep using its own noises (meaning the phone never rang inside the headset) and then I could push the 'answer/hang up' button and sound and mic would start working. I have now paired it with Windows 7, and it looks good. Under the playback menu I have 'Bluetooth Hands free Audio / Jabra BT200 (Mono Audio) / Ready', and under the recording menu I have 'Bluetooth Audio Input Device / Jabra BT200 (Mono Audio) / Ready'. However when I try to test the speakers Windows sends a sound, but I never hear it, and when I talk in the mic, Windows never hears me. If I right click either the Bluetooth mic or speakers there's an option to 'Connect', but it's grayed out and I cannot click it. As the final piece of knowledge I have, my headset blinks once every 3 seconds when it's in standby and I can't get that to change. If everything was working it should blink once every second at which point I think all of my problems would be fixed. Hence my issue: I can't seem to get my headset out of standby. On my headset I've tried sending it test noises and then pressing the 'Answer' button, but still nothing. The headset beeps when I press it, so it works, it just doesn't ever come out of standby. Is there maybe some way to trick my headset into thinking it's getting a phone call from my computer?

  Read the article

• Group policy not applying to security group

  - by ihavenoideawhatimdoing

  Preface: I have enough privileges to create GPOs in my OU, and have made a few of them for some simple tasks (like deploying a printer to certain users). Not actually a sysadmin...I'm a developer who is winging it. I wanted to create a GPO that would set a mapped folder for a certain security group (which I recently created and that contains only myself). Did the following: Created the GPO in MyOU - Users Removed the default Authenticted Users under Security Filtering Add the security group with my account to Security Filtering Set up the mapping via the User Configuration option Changed GPO Status to "Computer configuration settings disabled" Left WMI filtering to Closed the GPO at this point... Logged in as the target user; ran gpupdate /force Logged out, logged in, ran gpresult /r, no mention of my GPO Rebooted Logged in, re-ran gpupdate /force Logged out, logged in, ran gpresult /r, still no mention of my GPO If I log in with another completely different user, their RSOP information shows that the new GPO is being ignored due to a security restriction, so it appears to be "working" for other users. I just can't get it to actually show up in RSOP for the user it should be working. Is there anything else I can do short of rebooting endlessly and crossing my fingers?

  Read the article

• Why is my filesystem being mounted read-only in linux?

  - by Tim

  I am trying to set up a small linux system based on Gentoo on a VirtualBox machine, as a step towards deploying the same system onto a low-spec Single Board Computer. For some reason, my filesystem is being mounted read-only. In my /etc/fstab, I have: /dev/sda1 / ext3 defaults 0 0 none /proc proc defaults 0 0 none /sys sysfs defaults 0 0 none /dev/shm tmpfs defaults 0 0 However, once booted /proc/mounts shows rootfs / rootfs rw 0 0 /dev/root / ext3 ro,relatime,errors=continue,barrier=0,data=writeback 0 0 proc /proc proc rw,nosuid,nodev,noexec,relatime 0 0 sysfs /sys sysfs rw,nosuid,nodev,noexec,relatime 0 0 udev /dev tmpfs rw,nosuid,relatime,size=10240k,mode=755 0 0 devpts /dev/pts devpts rw,nosuid,noexec,relatime,gid=5,mode=620 0 0 none /dev/shm tmpfs rw,relatime 0 0 usbfs /proc/bus/usb usbfs rw,nosuid,noexec,relatime,devgid=85,devmode=664 0 0 binfmt_misc /proc/sys/fs/binfmt_misc binfmt_misc rw,nosuid,nodev,noexec,relatime 0 0 (the above may contain errors: there's no practical way to copy and paste) The partition at /dev/hda1 is clearly being mounted OK, since I can read all the data, but it's not being mounted as described in fstab. How might I go about diagnosing / resolving this? Edit: I can remount with mount -o remount,rw / and it works as expected, except that /proc/mounts reports /dev/root mounted at / rather than /dev/sda1 as I'd expect. If I try to remount with mount -a I get mount: none already mounted or /sys busy mount: according to mtab, sysfs is already mounted on /sys Edit 2: I resolved the problem with mount -a (the same error was occuring during startup, it turned out) by changing the sysfs and proc lines to proc /proc proc [...] sysfs /sys sysfs [...] Now mount -a doesn't complain, but it doesn't result in a read-write root partition. mount -o remount / does cause the root partition to be remounted, however.

  Read the article

• Monitor reset itself and now I can't set the resolution/settings back to how it was before

  - by verve

  I've had my LG 24" widescreen monitor since 2009 and 2 weeks ago I noticed the monitor turned itself off (never had it done this before) so I switched it back on to find all the settings like gamma, resolution etc. different = looked like it had been reset. Everyone in the house swears they never unplugged and plugged it back in. When I opened a webpage the fonts and zoom on the pages were different and my desktop was strange too; fonts of the icons were different etc. The screen seems blurry and when I watch movies the faces look distorted so I thought I would try to first figure out the resolution it used to be but when I go under "Adjust screen resolution" none of the options work and there is no recommended resolution marked; all the options stretch out the screen and looks terrible so right now I have it set to the least distorted one. Then since the resolution wasn't working I set the other manual settings(done by physical buttons on the monitor) back to how it used to be (luckily, I had written these down). The monitor looks better but the resolution makes it a strain to use. I thought maybe some Windows update caused this crap so I tried to System Restore: didn't work. What went wrong? A few questions: 1) What was the likely cause of the monitor shutting down itself and screwing up the settings I have been using since the day I bought the monitor? 2) Why have the fonts changed everywhere unless this is a HDD/video card problem? 3) How do I find the perfect resolution it used to be? The monitor wants me to set it to 1920 x 1080 but that isn't one of the options although I don't remember what resolution I used before. I use the 16:9 setting while I try the available resolution options but nothing looks good! How do I find what it used to be? Manual available in PDF under Support: http://www.lg.com/ca_en/computer-products/monitors/LG-lcd-monitor-W2442PA-BF.jsp Win 7. IE 9.

  Read the article

• 8007064c(2011) and 80280007(2009) persistant after all known repairs

  - by tiu44

  I'm on Windows 7 Home x64, and have ran into a major issue with Live Messenger(which I use daily). I have full offline installers for both 2011 and the last Wave 3 2009(14.0.8117.0416) Suites. Both give the following errors: Live Essentials 2011 Offline installer(official): An unknown error occured. Error:0x8007064c Source WLXSuite WL 2009 offline installer(official): You already have a more recent version of Windows Live. Error: OnCatalogResult:0x80280007 Next steps: If you want to install this older version, first uninstall any later versions that are on your computer. Get help with this error The 2011 installer also says it is updating messenger, I don't select anything else. Then last 2009 installer says their is a newer version that needs uninstalled even after the following procedures. MS Help pages provided all basically lead to using uninstall from control panel. Which I've uninstalled all Live components including watcom safety scanner and portable SQL from. I've followed online instructions for manually deleting folders from Program Files(x86), Appdata, and some others under \User\All Users and the one for the one account on the machine. I've used CCcleaner 3.01, ASC 3.7.3 and Beta 4 with deep scan along with deleting folders, and checked their uninstallers for Live components too, and none were there. wlmuninstaller.exe tool reports nothing, but after a failed install it finds something, but failes to clean it under all user admin privilege. The same errors still occur after all of that. Google searching I see people on forums suggesting reinstalling the OS cause MS doesn't even know how to fix this, but I'm hoping someone here can help. NOTE: I don't have System Restore or any other state freeze utilities going, and I don't have any real time AV going(I sometime scan with defender, anti rootkits, and online scanners). NOTE2:I posted this on windowslivehelp.com, before looking to see if the place was active or not, hoping I can get help here. Thanks

  Read the article

• Why is my biometric logon method no longer default and how to fix it? Win 7-based lenovo laptop

  - by StormRyder

  My laptop has been having some random problems with hibernating properly. That is a whole another topic that I still haven't resolved, but this is a different issue. The issues are connected, I guess, because one time after my computer experienced a failed hibernate, my login screen changed: since then my login screen always appears as the standard one with a prompt to type in a password. I can still use the finger scanner by clicking "other credentials" button. But that's annoying having to do that every time; previously the prompt to use finger scanner was the default one, whereas the typing password access was the alternate. How do I bring this arrangement back? In other words, how to switch the default from the type password prompt to the finger scan prompt? From online searches, I have only found discussions of turning the biometric access on or off... but clearly it is turned on and working, since I can use it. It's just not the default for some reason...

  Read the article

• How to disable irritating Office File Validation security alert?

  - by Rabarberski

  I have Microsoft Office 2007 running on Windows 7. Yesterday I updated Office to the latest service pack, i.e. SP3. This morning, when opening an MS Word document (.doc format, and a document I created myself some months ago) I was greeted with a new dialog box saying: Security Alert - Office File Validation WARNING: Office File Validation detected a problem while trying to open this file. Opening this is probably dangerous, and may allow a malicious user to take over your computer. Contact the sender and ask them to re-save and re-send the file. For more security, verify in person or via the phone that they sent the file. Including two links to some microsoft blabla webpage. Obviously the document is safe as I created it myself some months ago. How to disable this irritating dialog box? (On a sidenote, a rethorical question: Will Microsoft never learn? I consider myself a power user in Word, but I have no clue what could be wrong with my document so that it is considered dangerous. Let alone more basic users of Word. Sigh....)

  Read the article

• Apple / Mac OS X - Is there a Package Manager like Linux

  - by Walter White

  I am a Linux/UNIX user and love the package management that comes with it. For the most part, I like Ubuntu, but just like anything else, it is the minor things that you live with daily that would be nice if they just worked. My main issue is my wacom tablet while it works, every time there is an OS update, I have to rebuild the wacom driver. The other slightly annoying issue is, my ATI video card is not fully supported. When I use the HDMI out, the sound doesn't go through it, and the screen is not entirely used. I would happily get an Apple if it had a similar package management system like Ubuntu, Gentoo, or other Linux distribution. This takes the work out of getting the latest enhancements or fixes. It also takes all the guess work out about what you need to get something to work. I just want to use my computer, not administer it. Aside from Apple applications, if I wanted to install the GIMP on an apple, would it go and fetch ufraw if I wanted support for that and whatever other dependencies GIMP has? If I want Netbeans installed, will it go and get a JDK and maven if I want that? If not, is there something in the works? I know I don't update my applications that frequently, but that is mainly because I'm not aware of the updates. The updates all happen in the background. Walter

  Read the article

• Digitize video?

  - by kire

  I got some movies on a VCR that i want to move to my computer somehow. (for personal use) I have a video capture card and all hardware required. I'm looking for the software - programs, codecs etc. I like the format that most torrents come in and got some of these i'd like to use as reference for comparison. How can i see what codec, bitrate, etc a movie is using so i can pick this and know that it will work and look good. For AVI-files the bitrate is visible in explorer but it doesn't mention the codec used and i also have a lot of MKV-files that explorer can't handle. All kinds of tips, tricks and other suggestions are welcome. This is completely new to me. How do I avoid that video/audio gets out of sync for example, many movies you download have audio out of sync so i guess this can happen quite easily. The encoding-program has to run on windows and for playback the movies should work on at least VLC for windows.

  Read the article

• InstantSSL's certificate no different than a self signed certificate under Nginx with an IP accessed address

  - by Absolute0

  I ordered an ssl certificate from InstantSSL and got the following pair of files: my_ip.ca-bundle, my_ip.crt I also previously generated my own key and crt files using openssl. I concatenated all the crt files: cat my_previously_generted.crt my_ip.ca_bundle my_ip.crt chained.crt And configured nginx as follows: server { ... listen 443; ssl on; ssl_certificate /home/dmsf/csr/chained.crt; ssl_certificate_key /home/dmsf/csr/csr.nopass.key; ... } I don't have a domain name as per the clients request. When I open the browser with https://my_ip chrome gives me this error: The site's security certificate is not trusted! You attempted to reach my_ip, but the server presented a certificate issued by an entity that is not trusted by your computer's operating system. This may mean that the server has generated its own security credentials, which Google Chrome cannot rely on for identity information, or an attacker may be trying to intercept your communications. You should not proceed, especially if you have never seen this warning before for this site.

  Read the article

• Motherboard running rather hot while gaming

  - by I take Drukqs

  Case: Antec 1200 Mobo: Gigabyte GA-X58A-UD3R CPU: Intel i7 950 (stock cooler) GPU: EVGA GeForce 570 GTX RAM: 2x 2 GB (4 GB total) DDR3 dual-channel Corsair OS: Windows 7 Home Premium 64-bit This is my first build and it's brand new. I had no problems putting it all together in a few hours one evening and I consider myself to be pretty good with computers. Not to brag or anything like that! Just saying I've been fiddling with them since I was in diapers and I have a good amount of experience under my belt, just not with certain things yet. Recently while playing many of the latest games maxed out without a hitch my motherboard has been running hot and like anyone who's ever built a computer it scares the life out of me. I checked HWMonitor and saw that my motherboard sometimes reached temperatures of around 52 - 78c (the number 78 obviously being what's scaring me). I was wondering if such a temperature is normal and if not what the problem could be. Air flow in my case is phenomenal and besides having to ship back a faulty GPU and reseat my CPU my first build has been a very large success which I am enjoying tremendously. There is literally almost no dust in my case due to it being very new as previously mentioned and my RAM sticks are in the correct slots for dual-channel mode. My cable management is pretty great in my opinion with only cables from my PSU lingering in the bottom of the case. At any given opportunity I ran my cables behind my mobo. Air flow should definitely not be a problem because my CPU only goes up to about 60c and my GPU only goes up to about 80c. Thank you very much in advance.

  Read the article

• Is it possible to provide a wired ethernet connection to external devices with an extra LAN card?

  - by Ben McCormack

  I'm trying to provide a wired ethernet connection (wireless is not an option for this device) to a device (Samsung blu-ray player) without running Cat5 cable all over the home. I have a PC sitting next to this device and the PC is connected to the network via a wireless USB adapter. Is it possible to provide a wired connection from the PC to the wired device using the (currently unused) ethernet port in the back of the computer? Here's how I envision the device getting connected to the internet via my network: Linksys WRT54G v8 Wireless Router | ``--> Windows 7 PC connected via wireless | ``--> Blu-ray player connected via wired connection to the ethernet port on the PC. If so, how is this done? Will I need a crossover cable? What settings will I need to change in Windows 7 so that the device can connect? NOTE: I'm trying to avoid having to buy a wireless bridge and/or hacking a router with an open-source firmware to get this to work. See my previous question for more details.

  Read the article

• transparent git-svn gateway

  - by azatoth

  Currently we have an subversion repository with the following layout: /trunc /group1 /proj1 /proj2 group2 /proj3 /etc.. /tags /group1 /proj1 /proj2 group2 /proj3 /etc.. /branch /anything temporary I believe this is an rather bad layout, but at the moment it's difficult to change it fully. Personally I dislike subversion, due mostly the long time it takes to check history, and also that branching and merging are cumbersome etc. so I really want to use git instead. Sadly we cant just switch to git as the mental capacity for some might be to overwhelming, so I was looking into git-svn to see if I could practically use that to solve the issue. Sadly that directly ends up in a bad situation as I want to break down each project into one git repo, and I don't want to have to recreate the git-svn checkout on each computer I work on. so I though perhaps there is an possibility to create some sort of transparent git ?? svn proxy/gateway, so that an push to that repo "commits" to the svn repo, and an commit to the svn repo updates the git repo. Google hasn't been my friend, have only found generic usage help to use git-svn, so I ask you if you have some good ideas to accomplish this.

  Read the article

• Using UDF on a USB flash drive

  - by CesarB

  After failing to copy a file bigger than 4G to my 8G USB flash drive, I formatted it as ext3. While this is working fine for me so far, it will cause problems if I want to use it to copy files to someone which does not use Linux. I am thinking of formatting it as UDF instead, which I hope would allow it to be read (and possibly even written) on the three most popular operating systems (Windows, MacOS, and Linux), without having to install any extra drivers. However, from what I found on the web already, there seem to be several small gotchas related to which parameters are used to create the filesystem, which can reduce the compability (but most of the pages I found are about optical media, not USB flash drives). I would like to know: Which utility should I use to create the filesystem? (So far I have found mkudffs and genisoimage, and mkudffs seems the best option.) Which parameters should I use with the chosen utility for maximum compability? How compatible with the most common versions of these three operating systems UDF actually is? Is using UDF actually the best idea? Is there another filesystem which would have better compatibility, with no problematic restrictions like the FAT32 4G file size limit, and without having to install special drivers in every single computer which touches it?

  Read the article

• Valid IP address but can't surf without rebooting

  - by Kat

  I periodically lose internet and router connection at home. When this happens, others are using the router just fine. I am connecting directly through a wired connection to a Belkin router. I can release and renew the IP (and the IP addresses change to 0.0.0.0 and to an IP in my router's range beginning with 192.168.2. as they should) but still can't surf, can't access the router interface. Cycling the router doesn't help, and again, others are able to access the router fine at this time. Only rebooting the computer resolves the issue, and everything is wonderful for a few hours- and then I lose connection again. I have several ideas where to go from here, but I'd like to get some advice first. (Using Windows XP SP3, hardwired connection) Update As stated in the originally, releasing and renewing doesn't solve the issue. However, I have an update. I can ping localhost and my router IP with no problem at all when the issue occurs. However, repairing the network connection does not help. I AM able to get back on by disabling and then re-enabling the network connection in XP. What does that tell us?

  Read the article

< Previous Page | 593 594 595 596 597 598 599 600 601 602 603 604  | Next Page >