Search Results

Search found 27521 results on 1101 pages for '2012 memory manager kb'.

Page 602/1101 | < Previous Page | 598 599 600 601 602 603 604 605 606 607 608 609  | Next Page >

• MongoDB on 128mb 32-bit VPS (plus Tornado and Redis)

  - by apito

  i am curious about how mongodb will perform in a limited vps. specifically, i'll deploy this configuration on 32-bit ubuntu 9.04 server with 128Mb memory (UPDATE: now i'm considering 360mb too). nginx and redis three instances of tornado apps (one is for mobile site; limited app, not my primary audience); has around 8 Collections. social webapp for my community. mongodb all beside mongodb seems to have small footprint. memory-mapping-wise, i dont know how mongodb will behave. i know it's a little bit a stretch to use this kind of config on a tiny vps, but that's what i can afford for now. i expect to have.. hmm.. maybe ~50 15rps. i did my homework doing a lot of frontend optimizations and yslow says grade A 91 (ruleset V2) :-) anyone willing to share experiences? eg. how big the data set size when mongo hit the ceiling, performance when mongo do a lot of disk IO, etc. thanks. UPDATE: this is my pet project. i'll get back to you when i have next spare time to do same httperf in a vbox with exact spec. suggestion how to do stress testing welcomed. i'm new to this kind of stuff.

  Read the article

• Borked ubuntu uninstall - need to delete boot partition (i think)

  - by Max Williams

  I just got a new pc laptop with windows 7 and wanted to install Ubuntu on it. Which i did, no problem there, by downloading the installer, burning it to dvd then booting off the dvd and installing. Then, i realised that the new Ubuntu 12.04 uses the Unity desktop, which i immediately disliked, and after some research, began to hate. So, i decided (after a little googling) to install Linux Mint instead. So, thinking i'd better start from scratch, i went to the Windows 7 disk manager and wiped the Ubuntu partition that had been created. Now, when i start up, i get an error from grub, the ubuntu boot manager: error: unknown filesystem grub rescue> _ and a blinking cursor where i can enter commands. I suspect that what i've done is deleted the main ubuntu partition but NOT deleted another partition which is a boot partition, or something like that? Can anyone tell me how i can rescue or unbork this? I'd like to either a) get back to my original windows-only setup OR b) install linux mint off dvd (which i have), into the empty partition, fixing any grub confusion in the process. Any suggestions? Thanks, max BTW please don't answer if you're just going to tell me to stick with 12.04, or install a different distro or something. I definitely want Mint and just want to fix this mess - thanks :)

  Read the article

• System occasionally hangs boot process with SLES 11

  - by ThaMe90

  I have several (new) systems on which I had to install SLES11 on. However, after a few (though not every) reboots, the system hangs during the boot sequence. It will only continue after I physically press a key on the keyboard. From what I've found in the dmesg log from a failed boot is the following: [ 22.170276] sd 0:0:0:0: [sda] Mode Sense: b7 00 00 08 [ 22.171155] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 22.182760] sda: sda1 sda2 sda3 [ 22.383424] sd 0:0:0:0: [sda] Attached SCSI disk [ 22.545372] PM: Marking nosave pages: 000000000009a000 - 0000000000100000 [ 22.545377] PM: Marking nosave pages: 00000000bf780000 - 0000000100000000 [ 22.546217] PM: Basic memory bitmaps created [ 22.590380] PM: Basic memory bitmaps freed [ 22.596284] PM: Starting manual resume from disk [ 22.602319] PM: Resume from partition 8:1 [ 22.602321] PM: Checking hibernation image. [ 22.602479] PM: Error -22 checking image file [ 22.602481] PM: Resume from disk failed. [ 22.718727] kjournald starting. Commit interval 15 seconds [ 22.718960] EXT3-fs (sda3): using internal journal [ 22.718964] EXT3-fs (sda3): mounted filesystem with ordered data mode [ 1555.644404] udevd version 128 started [ 1555.697664] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0 [ 1555.707961] ACPI: Power Button [PWRB] I've looked around the internet for the PM: Resume from disk failed. message, but this seems to only be important when restoring the system after a hybernate, i.e. restore from the hdd. But this is not my situation. I only get this after a reboot, as I said before. The timestamp [ 1555.xxxxxx] is only the result of me pressing a key on the keyboard. Any suggestions on how to proceed? As I am getting stuck on this issue.

  Read the article

• SQL Server Installation: Is it 32 or 64 bit?

  - by CapBBeard

  Hi, Recently I was performing an OS upgrade on one of our DB servers, moving from Server 2003 to Server 2008. The DBMS is SQL Server 2005. While reinstalling SQL on the new Windows installation, I went to another of our DB servers to verify a couple of settings. Now, I always thought this second server was Server 2003 x64 + SQL 2005 x64 (from what I'd been told), but I now have my doubts about this. I now suspect that it is in fact only 32 bit SQL, however I'd like to verify this. Here's some details: The OS is definitely 64 bit. xp_msver shows Platform as NT INTEL X86 SELECT @@VERSION shows Microsoft SQL Server 2005 - 9.00.4035.00 (Intel X86)... However sqlservr.exe is not shown with '* 32' in taskmgr, does anyone know why this is the case, if it is in fact 32 bit as claimed? Despite this, it does seem to be running out of the x86 program files folder. If I do the same checks on a confirmed 64 bit installation, it does give back the expected 64 bit readings, which can only prove that this server in question is only running in 32 bit. Now, that being the case, the question arises about how much memory this '32 bit' install can use. Task manager reports about 3.5GB memory usage for sqlservr.exe (The server has 16GB physical). I suspect that AWE has not been configured at all, and therefore the server will be significantly under-utilised (remembering that the OS is 64 bit) if SQL is simply using a 32bit address space. Is this assumption correct? I feel the server should have SQL reinstalled as 64 bit in order to fully utilise the hardware platform, however it is currently heavily in production; this will be no easy task. I suspect we may just have to configure AWE correctly and let it be for the time being (Unless this is a bad idea?). I apologise that this question is a little vague/lost; I'm no SQL expert, just trying to get a handle on what's going on here.

  Read the article

• Site Goes Offline Every Day At Midnight - No One Knows Why

  - by HollerTrain

  0 down vote favorite Seems today a website I manage has been going online and offline between 12a and 12:25a. I have no idea what is causing the issue so I am seeking guidance on where to start. It is a Wordpress based site. So here is what I DO know: I have a pingdom account which alerts me when the site goes offline so we can see every day, like clockwork, the site goes on/off. At the time of the ups/downs I see a lot of strain on the memory usage. Look at the load average when the site is going online/offline (http://screencast.com/t/BRlfXkqrbJII). Then I ran this command to restart http (http://screencast.com/t/usVtYWZ2Qi) and the memory usage then goes down to this (http://screencast.com/t/VdTIy3bgZiQB). An hour after I restarted http, the site then went offline/online so restarting the http didn't do much help. When the site is going offline/online, I ran the top command and get this (http://screencast.com/t/zEwr7YQj3). Here is a top command when the site is at it's lowest (http://screencast.com/t/eaMfha9lbT - so this would be dubbged "normal"). Here is a bandwidth report (http://screencast.com/t/AS0h2CH1Gypq). The traffic doesn't seem to be that much (http://screencast.com/t/s7hrWNNic1K), but looking at my times the site is going up/down this may be one of the reasons? I have the dvp Nitro package at Media Temple (http://mediatemple.net/webhosting/nitro/). So at this point I would request some help in trying to figure out what the cause of this is, and how I can go about pinpointing this issue. ANY HELP is greatly appreciated.

  Read the article

• Building vs buying a server for an academic lab [closed]

  - by Roy

  I'm looking for advice on the classic build vs buy question. We need a new linux server to run Matlab computation on in our lab (academic). Matlab parallel computing toolbox licence allows up to 12 local workers so we are aiming at a 12 core server with 4GB memory per core (total of 48gb). The system will have an SSD for the OS and a raid-5 (4x2tb) for data. I looked around and found a (relatively) cheap vendor, Silicon Mechanics, that offers a system to our liking (specs below) for $6732. However, buying the components from newegg cost only $4464! The difference is $2268 which is 50% of the base cost. If buying from a company can be thought of as a sort of insurance, basically my premiums are of 50% of the base cost which to me sounds like a lot. Of course any downtime is bad, but the work is not "mission critical", i.e. if it takes a few days to fix it when it breaks its no the end of the world. If it takes weeks to months then its a problem. If it breaks 2-3 times in 3 years, not too bad. If it breaks every month not good. In term of build experience, I set up a linux cluster in grad school (from existing computers) and I build my home pcs but I never built a server before. The server components I'm thinking about: 1 x SUPERMICRO SYS-7046T-6F 4U Tower Server Barebone Dual LGA 1366 Intel 5520 DDR3 1333/1066/800 ($1,050) 12 x Kingston 4GB 240-Pin DDR3 SDRAM DDR3 1333 (PC3 10600) ECC Unbuffered Server Memory ($420) 2 x Intel Xeon E5645 Westmere-EP 2.4GHz LGA 1366 80W Six-Core ($1,116) 4 x Seagate Constellation ES 2TB 7200 RPM SATA 6.0Gb/s 3.5" ($1,040) 1 x SAMSUNG Internal DVD Writer Black SATA ($20) 1 x Intel 520 Series 2.5" 180GB SATA III MLC SSD $300 1 x LSI LSI00281 PCI-Express 2.0 x8 MD2 Low profile SATA / SAS MegaRAID SAS 9260CV-4i Controller Card, $695

  Read the article

• Large, high performance object or key/value store for HTTP serving on Linux

  - by Tommy

  I have a service that serves images to end users at a very high rate using plain HTTP. The images vary between 4 and 64kbytes, and there are 1.300.000.000 of them in total. The dataset is about 30TiB in size and changes (new objects, updates, deletes) make out less than 1% of the requests. The number of requests pr. second vary from 240 to 9000 and is dispersed pretty much all over, with few objects being especially "hot". As of now, these images are files on a ext3 filesystem distributed read only across a large amount of mid range servers. This poses several problems: Using a fileysystem is very inefficient since the metadata size is large, the inode/dentry cache is volatile on linux and some daemons tend to stat()/readdir() it's way through the directory structure, which in my case becomes very expensive. Updating the dataset is very time consuming and requires remounting between set A and B. The only reasonable handling is operating on the block device for backup, copying, etc. What I would like is a deamon that: speaks HTTP (get, put, delete and perhaps update) stores data it in an efficient structure. The index should remain in memory, and considering the amount of objects, the overhead must be small. The software should be able to handle massive connections with slow (if any) time needed to ramp up. Index should be read in memory at startup. Statistics would be nice, but not mandatory. I have experimented a bit with riak, redis, mongodb, kyoto and varnish with persistent storage, but I haven't had the chance to dig in really deep yet.

  Read the article

• A little guidance setting up FTP server authentication on Windows Server 2008 R2 standard?

  - by Ropstah

  I have a (clean) server running Windows Server 2008 R2 standard. I would just like to use it for serving a website and a FTP server through IIS. IIS is installed and serves my website propery. I have now added a FTP site but when I try to logon using my user/pass i get the following error: 530 User cannot login From this article (http://support.microsoft.com/kb/200475) I understand that these four causes can be pointed out: The Allow only anonymous connections security setting has been turned on in the Microsoft Management Console (MMC). Not the case The username does not have the Log on locally permission in User Manager. The user is in the Users group, however I'm not able to logon through RDP. I tried configuring this by following this article through GPMC however this only works when I'm logged in as a domain user on a domain controller which I'm not: I'm logged in as administrator The username does not have the Access this computer from the network permission in User Manager. Not sure what this implies...? The Domain Name was not specified together with the username (in the form of DOMAIN\username). Tried adding the server name: server\username, not working... I am an absolute server noob and I'd just like to be able to connect through FTP... Any guidance is highly appreciated!

  Read the article

• Random server lag, no CPU/mem/pagefile usage

  - by Kev

  We have a fairly new server running Windows 2003 SP2, and the past few days we've noticed random slowdowns. When I'm logged into the server over remote desktop while this is happening, or if I'm physically sitting at the server logged in, suddenly everything becomes extremely laggy. Any UI element I try to interact with takes upwards of ten seconds to react, and then responds very slowly. Then a minute later everything is quite snappy again. During this, I have Task Manager minimized to the tray, and there's no CPU usage. I open it up right after this happens, and there's very little CPU usage on the graph, and no memory or pagefile usage above normal. (Normal being 1.5 GB free in the case of memory.) This is what I see logged into the server, and then users start calling saying things are slow, timing out, and failing--anything to do with our server. No events in the Event Viewer around the times this happens. The context I'm working in (last thing I clicked, etc.) seems different every time--different programs active, different combinations of programs open. Never anything particularly stressful (like adding an event entry to a Cobian Backup configuration, or editing text in TextPad, which has been exceptionally stable in my extensive usage of it.) I would've thought it was just the server, but a family member's home PC (entirely separate) running WinXPSP3 had the same thing happen to it last night a few times. Is this some new behaviour introduced by the latest Windows Updates? Either way, where do I even start to look when nothing seems to be chewing up resources?

  Read the article

• Clustered MSDTC

  - by niel

  Hi I'm setting up a SQL cluster (SQL 2008), Windows 2008 R2. I enable the network access on local dtc and then create a DTC resource in my cluster . the problem is that when i start up the resource it does nto pull through my settings to enable network access. the log shows this: MSDTC started with the following settings: Security Configuration (OFF = 0 and ON = 1): Allow Remote Administrator = 0, Network Clients = 0, Trasaction Manager Communication: Allow Inbound Transactions = 0, Allow Outbound Transactions = 0, Transaction Internet Protocol (TIP) = 0, Enable XA Transactions = 0, Enable SNA LU 6.2 Transactions = 1, MSDTC Communications Security = Mutual Authentication Required, Account = NT AUTHORITY\NetworkService, Firewall Exclusion Detected = 0 Transaction Bridge Installed = 0 Filtering Duplicate Events = 1 where when i restart the local dtc service it says this: Security Configuration (OFF = 0 and ON = 1): Allow Remote Administrator = 0, Network Clients = 1, Trasaction Manager Communication: Allow Inbound Transactions = 1, Allow Outbound Transactions = 1, Transaction Internet Protocol (TIP) = 0, Enable XA Transactions = 1, Enable SNA LU 6.2 Transactions = 1, MSDTC Communications Security = No Authentication Required, Account = NT AUTHORITY\NetworkService, Firewall Exclusion Detected = 0 Transaction Bridge Installed = 0 Filtering Duplicate Events = 1 settings on both nodes in teh cluster is the same. I have reinstalled and restarted to many times to mention. Any ideas ?

  Read the article

• Changing the default boot option without losing the boot menu

  - by hvd

  I've had a working multi-boot setup with the Windows boot loader, containing menu items for two Windows 7 systems, and one for Grub. Grub in turn contains multiple menu items, but I think that's not relevant here. I've upgraded one system to Windows 8. When I now set a different system as the default, I lose the boot menu, and I lose the possibility of booting into the other systems. I've set Windows 7 as the default, rebooted, and get Windows 7, but I don't get to choose which system to boot into. I can run its own bcdedit to change the default back to Windows 8, and another reboot shows the boot menu again, but how can I avoid defaulting to Windows 8? Here are my current boot settings, is there anything that is misconfigured? C:\WINDOWS\system32>bcdedit Windows Boot Manager -------------------- identifier {bootmgr} device partition=F: description Windows Boot Manager locale nl-NL inherit {globalsettings} integrityservices Enable default {current} resumeobject {2f8b77f0-a30b-11e1-a9c6-a4bd8d37f662} displayorder {current} {2f8b77e3-a30b-11e1-a9c6-a4bd8d37f662} {2f8b77ee-a30b-11e1-a9c6-a4bd8d37f662} toolsdisplayorder {memdiag} timeout 30 Windows Boot Loader ------------------- identifier {current} device partition=C: path \WINDOWS\system32\winload.exe description Windows 8 locale nl-NL inherit {bootloadersettings} integrityservices Enable recoveryenabled No allowedinmemorysettings 0x15000075 osdevice partition=C: systemroot \WINDOWS resumeobject {2f8b77f0-a30b-11e1-a9c6-a4bd8d37f662} nx OptIn bootmenupolicy Standard Windows Boot Loader ------------------- identifier {2f8b77e3-a30b-11e1-a9c6-a4bd8d37f662} device partition=D: path \Windows\system32\winload.exe description Windows 7 locale nl-NL osdevice partition=D: systemroot \Windows resumeobject {59616f59-a2ba-11e1-b73a-806e6f6e6963} nx OptIn pae Default bootmenupolicy Standard hypervisorlaunchtype Auto detecthal Yes sos No debug No Real-mode Boot Sector --------------------- identifier {2f8b77ee-a30b-11e1-a9c6-a4bd8d37f662} device partition=C: path \grub\winloader\grub.boot description Grub 2

  Read the article

• Server slowdown

  - by Clinton Bosch

  I have a GWT application running on Tomcat on a cloud linux(Ubuntu) server, recently I released a new version of the application and suddenly my server response times have gone from 500ms average to 15s average. I have run every monitoring tool I know. iostat says my disks are 0.03% utilised mysqltuner.pl says I am OK other see below top says my processor is 99% idle and load average: 0.20, 0.31, 0.33 memory usage is 50% (-/+ buffers/cache: 3997 3974) mysqltuner output [OK] Logged in using credentials from debian maintenance account. -------- General Statistics -------------------------------------------------- [--] Skipped version check for MySQLTuner script [OK] Currently running supported MySQL version 5.1.63-0ubuntu0.10.04.1-log [OK] Operating on 64-bit architecture -------- Storage Engine Statistics ------------------------------------------- [--] Status: +Archive -BDB -Federated +InnoDB -ISAM -NDBCluster [--] Data in MyISAM tables: 370M (Tables: 52) [--] Data in InnoDB tables: 697M (Tables: 1749) [!!] Total fragmented tables: 1754 -------- Security Recommendations ------------------------------------------- [OK] All database users have passwords assigned -------- Performance Metrics ------------------------------------------------- [--] Up for: 19h 25m 41s (1M q [28.122 qps], 1K conn, TX: 2B, RX: 1B) [--] Reads / Writes: 98% / 2% [--] Total buffers: 1.0G global + 2.7M per thread (500 max threads) [OK] Maximum possible memory usage: 2.4G (30% of installed RAM) [OK] Slow queries: 0% (1/1M) [OK] Highest usage of available connections: 34% (173/500) [OK] Key buffer size / total MyISAM indexes: 16.0M/279.0K [OK] Key buffer hit rate: 99.9% (50K cached / 40 reads) [OK] Query cache efficiency: 61.4% (844K cached / 1M selects) [!!] Query cache prunes per day: 553779 [OK] Sorts requiring temporary tables: 0% (0 temp sorts / 34K sorts) [OK] Temporary tables created on disk: 4% (4K on disk / 102K total) [OK] Thread cache hit rate: 84% (185 created / 1K connections) [!!] Table cache hit rate: 0% (256 open / 27K opened) [OK] Open file limit used: 0% (20/2K) [OK] Table locks acquired immediately: 100% (692K immediate / 692K locks) [OK] InnoDB data size / buffer pool: 697.2M/1.0G -------- Recommendations ----------------------------------------------------- General recommendations: Run OPTIMIZE TABLE to defragment tables for better performance MySQL started within last 24 hours - recommendations may be inaccurate Enable the slow query log to troubleshoot bad queries Increase table_cache gradually to avoid file descriptor limits Variables to adjust: query_cache_size (> 16M) table_cache (> 256)

  Read the article

• Flash Backed Write Cache (FBWC) without capacitor pack

  - by Martyn

  I brought a HP Smart Array P410 controller and it is installed and working fine in a HP Prolient Microserver with 4 drives in two RAID 1 arrays. I didn’t realise however that it came without any cache so would only work by directly writing straight to the disk, and the performance was horrible. So I then brought the 512MB Flash Backed Write Cache (FBWC) memory module as I was under the impression that with FBWC I would not need a battery. I got this idea from a forum post. "What do you guys think of the choice between 'BBWC' (battery backed write cache) and 'FBWC' (flash backed write cache)? The flashed based ones use non-volitile memory so need no battery." After installing the cache module however the server pretty much won’t boot. The P410 has a flashing amber light on it, and from the manual that doesn’t sound good. I’ve managed to get to the on board BIOS once and even managed to get to boot to the HP Array Configuration Utility (ACU) CD once, but every other time the Server continuingly reboots once it get to the POST screen and reads ARRAY INITILIZING %%%. The one time I reached the ACU, it reported a problem with the Cache Module. To me, it seems like the cache module is faulty, however the supplier tells me “Do you have an FBWC battery pack, p/n 587324-001, because that is required for the cache to work. If you have it, please complete an RMA form and we'll send a replacement / credit.” Does this sound right to you? I’ve been ordering the parts from the US and I don’t want to spend $77 + $40 p&p on a battery, wait a week for the shipping to find the card is faulty, and I don’t want to send back a working card?

  Read the article

• Diagnose remote desktop freezes in Windows 7 when no BSOD?

  - by Paul Smith

  Okay, I'm getting no joy from Asus or Microsoft on this, so hoping for some clues on how to narrow down the cause. I have very frequent OS freezes, always & only when running Remote Destkop Client (mstsc) in Windows 7 x64. I never have a bluescreen, and there is never a minidump. The display & input just freezes -- no keyboard, no mouse, and sound will just continue the last wavelength if any. So far, I can't find a way to trap the hang given that there's no bluescreen; advanced startup & recovery settings for system failure are "Write an event" checked, "Automatically restart" checked, and "Kernel memory dump". I've updated to the lasted BIOS, and tried a few different graphics drivers, both generic & ATI. I've also tried disabling Aero, and everything about the remote desktop experience (incrementally unchecked every box in the mstsc - options - experience tab), even disabled/unplugged external monitor to make sure it wasn't a dual-monitor issue. My specs are: Asus G73jh notebook 8GB RAM ATI Mobility Radeon HD 5800 Series graphics (recently tried driver versions 8.791.0.0, 8.801.0.0) American Megatrends G73jh.211 BIOS (7/27/2010) Windows 7 Home Premium x64 Windows Memory Diagnostic passed all of the following at least 3 times with no errors: MATS+ INVC LRAND Stride6 WMATS+ WINVC This notebook is better than most at removing heat (laudable vent design), so I'm not inclined to suspect thermal causes (especially since running 1080p video for hours has never caused a freeze, but mstsc does, reliably, within 5 minutes to an hour). This did seem to start happening after a Windows Update, but I've since reverted every patch applied since a week before the first occurrence, with no joy. (And I'd only had the PC for a couple weeks before that, so it could have been chance + less actual time spent remoting at the beginning.) I'm at my wits end, and I bought this laptop primarily as a remote terminal client (go figure, right?) Any ideas on how to identify the cause of this? Thanks!

  Read the article

• How to disable monitor "sleep" on Ubuntu without access to X?

  - by exhuma

  I just received a CuBox (basically a tiny ARM based PC). It comes pre-installed with Ubuntu, and I did not (yet) want to fiddle with the OS itself. My aim is to have it automaticall start a browser in fullscrren upon boot. Using chromium with the "--kiosk" flag works perfectly in that regard. But now I have the problem that the screen turns off after a certain time. I managed to turn off the screen saver using: gconftool-2 -s /apps/gnome-screensaver/idle_activation_enabled --type=bool false And tried to turn off the power management using: gconftool-2 -s /apps/gnome-power-manager/ac_sleep_display --type=int 0 and gconftool-2 -s /apps/gnome-power-manager/timeout/sleep_display_ac --type=int 0 Neither of the power-management commands worked. Theoretically I could hook up a mouse and keyboard and configure it manually. But I want to learn how to do it over the console. The box will eventually be only reachable via SSH. So I'd like to be able to trouble-shoot it later. I don't quite know where to look for. I searched the gconf tree using gconftool-2 -S for anything related to the terms power, idle and sleep but did not find anything promising. Maybe it's not even gconf related... Any ideas what else I could look for?

  Read the article

• "What happens?" server performance monitor

  - by AlexAtNet

  Hello! After reviewing some thread about server monitoring software I end up with a simple question: Which of the server monitoring tools should I use for automatic detection of "abnormal" situations with recommendations on how to fix them? I look for software that checks the system performance after installation and calculate some average load values (memory, CPU, etc). And when something happens (CPU load is increased to 20%) then it tries to detect a reason for this. If it is apache, it should check for access logs. If mysql, it should check mysql logs and tell me what happens. It this is because some user decodes a lot of images, I'd like to know which command is executed, when and user name. The same for disk usage, memory, number of processes, threads and so on. Ideally, this software should periodically checks the system and report problems: errors in PHP error log, outdated packages, security vulnerabilities. In other word I'm looking a software that will keep my simple Debian/Apache/PHP/MySQL server without forcing me to monitor the charts every day. I hope that such program exists. Thanks, Alex

  Read the article

• fglrx-legacy-driver not seeing Radeon HD 4650 AGP

  - by Rocket Hazmat

  I am running Debian Squeeze on an old Dell Dimension 8300 box. It has an AGP Radeon HD 4650 card. I use this machine to mine bitcoins, and today I noticed that the machine had rebooted! My precious uptime! Anyway, my miner wouldn't start, so I figured might as well update my graphics driver, maybe that would fix the issue. I went to amd.com and downloaded the newest driver (12.6 legacy), but after installing it, aticonfig gave an error: aticonfig: No supported adapters detected I uninstalled the driver and figured I'd try to install it from apt. AMD has dropped support for the HD 4000 series in fglrx, forcing me to use fglrx-legacy-driver (currently only in experimental). In order to install this, I had to update libc6 (and some other important packages, like gcc), I had to use their wheezy versions. I finally got fglrx-legacy-driver installed, but I still got: aticonfig: No supported adapters detected Why isn't the driver finding my video card? I have a hunch it has something to do with the fact that it's an AGP video card. Here is the output of lspci -v (why does it say Kernel driver in use: fglrx_pci?): 01:00.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI RV730 Pro AGP [Radeon HD 4600 Series] (prog-if 00 [VGA controller]) Subsystem: Advanced Micro Devices [AMD] nee ATI Device 0028 Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 16 Memory at e0000000 (32-bit, prefetchable) [size=256M] I/O ports at de00 [size=256] Memory at fe9f0000 (32-bit, non-prefetchable) [size=64K] Expansion ROM at fea00000 [disabled] [size=128K] Capabilities: [50] Power Management version 3 Capabilities: [58] AGP version 3.0 Kernel driver in use: fglrx_pci EDIT: fglrx 12.4 seems to work. Thing is, since I am on kernel 3.2, I need to apply this patch to common/lib/modules/fglrx/build_mod/firegl_public.c. I thought ATI dropped support for the 4xxx series after 12.4. Why doesn't 12.6 legacy work?

  Read the article

• Windows based development environment: HyperV, VMWare, or VirtualBox on development machine?

  - by bleepzter

  I am a software engineer with a little bit of an informal "support" functionality... I am trying to figure out what is the best possible approach to employing virtualization technologies into our development process. Since the code we develop is server-centric, testing it often requires a VM with specific software requirements. I used to use VM Ware player (free version) to run my VM's until both of my laptops started exhibiting issues with corrupted windows 7 services and dying hard drives. All leads pointed to VMWare, which by the way seems to be a solid product if you pay for the Workstation edition ($300). On a side note, I have always been a fan of the Windows Server product line. I think it makes for one of the best development environments out there - it is highly scalable, highly reliable, and very efficient. So to be fair I replaced the drives of the laptops and installed Windows Server 2008R2, VS2010 Ultimate SP1, SQL Server 2008R2, TFS Server 2010 and all other tools and API's needed do do my work properly. So now I am stuck with a bunch of VMWare VMs. I don't want to repeat of what happened before, and I certainly don't want to bog down my machine with an inefficient hypervisor or services that are not needed. Futhermore the VMDK hard-disk format used by VMWare is not compatible with the VHD format of Hyper V. It is my understanding that converting from one format to the other can only happen by Microsoft System Center Virtual Machine which I have downloaded from MSDN and ready to install. I guess the question at this point is: Does SCVM run as another service in Windows? Is it a memory hog? What is a better virtualization technology - Hyper-V or Virtual Box in terms of efficiency ease of use and most importantly - memory footprint? (Keep in mind the development environment already has a ton of services running such as TFS Server, SQL Server, IIS, etc...) How would you advise to proceed at this point so that the VMs are still used in the test process? Thanks Martin

  Read the article

• Incredble low disk performance on HP DL385 G7

  - by 3molo

  Hi, As a test of the Opteron processor family, I bought a HP DL385 G7 6128 with HP Smart Array P410i Controller - no memory. The machine has 20GB ram 2x146GB 15k rpm SAS + 2x250GB SATA2, both in Raid 1 configurations. I run Vmware ESXi 4.1. Problem: Even with one virtual machine only, tried Linux 2.6/Windows server 2008/Windows 7, the VMs' feel really sluggish. With windows 7, the vmware converter installation even timed out. Tried both SATA and SAS disks and SATA disks are nearly unsusable, while SAS disks feels extremely slow.I can't see a lot of disk activity in the infrastructure client, but I haven't been looking for causes or even tried diagnostics because I have a feeling that it's either because of the cheap raid controller - or simply because of the lack of memory for it. Despite the problems, I continued and installed a virtual machine that serves a key function, so it's not easy to take it down and run diagnostics. Would very much like to know what you guys have to say of it, is it more likely to be a problem with the controller/disks or is it low performance because of budget components? Thanks in advance,

  Read the article

• Weird glitches on Intel iGPU

  - by FrederikVds

  I have a weird problem that I can't manage to describe in one word, so I'm having trouble searching for a solution. My monitors sometimes go black for a tenth of a second. Other times, they show the image shifted a few centimeters to the left or to the right. This happens on both of my monitors, but not necessarily at the same time. I would say it happens about once a minute, unless under heavy load, in which case it can happen every second or so. Interestingly, heavy CPU/memory usage can also cause this, not just heavy GPU usage. This only happens when they are both at 1920x1080, not when one of them, or both, are at a lower resolution. It also happens when they are in mirrored mode instead of extended desktop mode. My GPU is obviously not at full clock speed most of the time: this happens at 350 MHz as well as at 1200 MHz. So it doesn't seem like a matter of too little performance. I'm not seeing any traditional artefacts, even when I use MSI Kombustor, only this kind of full-screen glitches. CPU stressing software isn't reporting any issues either. I'm thinking maybe the connection between my CPU and my PCH isn't fast enough, but I can't find anyone with the same problem to confirm that. I'd rather not invest in a discrete GPU without being certain it will fix something. Does anyone know how to search for this, or even better, does anyone have a solution? My full specs are below. Thanks in advance! Specs: ASUS P8Z77-M Intel Core i5-3570K (with Intel HD 4000 Graphics) 2x4 GB AMD Performance Edition memory Corsair Force 3 Series Rev. B 120GB SSD Maxtor 200GB HD Lite-On DVD-RW Antec 350 Watt PSU 64-bit Windows 7 Professional 2x Iiyama ProLite E2208HDS display

  Read the article

• How can I install git on RHEL 6?

  - by JR.Xyza

  I'm trying to install Git on a RHEL6 development server, I have experience with Ubuntu but this is my first time working with RHEL (I'm a developer trying to fill in for a recently departed Linux Sysadmin). I've set up two additional repos (EPEL and IUS) for other packages needed for a Magento install. Output of yum repolist: [root@box]# yum repolist Loaded plugins: product-id, security, subscription-manager Updating certificate-based repositories. repo id repo name status epel Extra Packages for Enterprise Linux 6 - x86_64 7,841 ius IUS for RHEL 6Server - x86_64 135 Most of what I've read indicates a simple 'yum install git' should work with EPEL enabled, but I get the dreaded [root@box]# yum install git Loaded plugins: product-id, security, subscription-manager Updating certificate-based repositories. Setting up Install Process No package git available. Error: Nothing to do Same goes for git-daemon, etc. I've tracked down a number of git RPMs such as this one at repoforge but they require a train of dependencies that seems to never end. I've also toyed with compiling it manually but the rabbit hole to get make working seems to go even deeper. I'm convinced there's a simple oversight somewhere keeping me from being able to install from the EPEL repo, but I'm a rookie at all this. Thanks in advance for help/pointers/additional resources.

  Read the article

• SATA DVD drive refuses to read movie DVDs

  - by poke

  Hey, I have a problem with my DVD Drive (Asus DRW-2014L1T, most current firmware installed) on Windows 7 x64. When I insert a DVD movie and Windows starts to access the drive (for autoplay, or when I manually click on the drive icon), my computer hangs up in a particular way, while trying to read the disk. Explorer stops reacting and several programs won't run or their launch is horribly delayed (like the device manager). In th end, I can't access the movie and can't even eject the disk (probably because Windows is still trying to access it). To get the disk out of the drive I then have to reboot (which sometimes doesn't work either) and eject the disk before Windows boots. BIOS recognizes the drive just fine, and Windows is also able to read data disks (tried it with some software disks), but just refuses any movies. I have checked the region code in the device manager, but it is correct. My notebook is reading the disks just fine btw.. I remember having the same problem with an older drive as well, but I don't remember what I did to make it work again (maybe I didn't even fix the problem back then). I do remember however that booting with the disk inserted made Windows recognize the disk, however this doesn't work in this situation either. Do you have any idea what to do to fix that problem?

  Read the article

• Enable bitlocker an save key to share

  - by user273694

  I have searched all over the web but cannot find a complete answer to this: How to enable Bitlocker on a laptop with TPM, and store a file with the Bitlocker recovery key and TPM password by USING THE manage-bde command line tool. The file should be the same as when created in the Bitlocker manager UI. I DO NOT want to save to AD. The same question was asked here but was not answered correctly. The goal is to write a script to be used with an endpoint manager. I have tried the following: manage-bde -on C: Works fine, but does not create or save a key. manage-bde -on C: -rk C:\myfolder\ and manage-bde -on C: -RecoveryKey C:\myfolder\ -rp The output from the last two methods state that a key has been saved to c:\myfolder and so on, but that is not the case. It also says that I have to: Save the password in a secure location Insert a USB flash drive with an external key file into the computer. Restart and run hardware test type "manage-bde -status" to check if the hardware test succeeded After a restart, I get an error saying that Bitlocker could not be enabled because the bitlocker startup key or recovery kpassword cannot be found on the USB device.... C: was not encrypted. Why am I asked to insert a USB?? I simply want to encrypt the hard drive and save the recovery information to a file automatically. Is that too much to ask? Help please!

  Read the article

• Grayed-Out Sleep and Hibernate Options on Windows 7 After Updating Graphics Driver

  - by Maxim Zaslavsky

  I have a Gateway M275 Tablet PC, on which I've installed Windows 7 Ultimate. The laptop is quite old, so there aren't any Win7 drivers for it, not to mention any Vista drivers. Win7 has been working for some time, but I noticed that my video output wasn't working. I went into Device Manager and found that I didn't have a driver for my video card: it just recognized it as the standard one. I searched online and found an XP driver for it, released by Gateway. Device Manager accepted this driver and prompted me to reboot. After that, I noticed that my Sleep and Hibernate options in the Shut Down menu have been grayed-out. I looked online and found that many people are attributing this to display drivers, as such an old driver would surely not be compatible with the standby procedures Windows 7 uses. To make it clear: I was able to Sleep and Hibernate before updating the drivers; now, I can't. Running powercfg /a gives me, "An internal system component has disabled this standby state," for each available standby mode. Is there some way that the driver can be modified to support hibernation? The new driver fixed my video output problem, but I guess hibernation is more important for me. If not, what steps should I take to remove the driver and just leave the standard Windows one, which previously supported hibernation and sleep on this computer? Thanks in advance.

  Read the article

• Ubuntu on VPS becomes unresponsive: BUG: soft lockup - CPU#0 stuck for 22s

  - by Bhante Nandiya

  We have a VPS running Ubuntu, on Xen. The problem is this, about once a day, for about 20-50 minutes, at a random time, the server becomes completely unresponsive to the outside world. After this period, it becomes responsive again, as if nothing had happened, it doesn't lose uptime, it doesn't restart. It just starts responding again as if it had been in suspended animation. These outages occur under conditions of non-exceptional memory and cpu, for example 70% mem, 5% cpu. I have stopped all non-essential services so the usage is very even. These outages don't particularly occur during times of increased memory/cpu (during daily tasks), they sometimes occur at times of very low cpu use (<2%), but in the past also occured during swapping. These blackouts have been occurring both under Ubuntu 12.04 LTS, and Ubuntu 14.04 LTS - no change at all (I upgraded Ubuntu specifically to see if it helped this problem). It is possible to log into our webhosts site, and use their administration console to see error messages from during this time. Presumably, these messages are from the Xen virtualization, the main message goes like this: BUG: soft lockp - CPU#0 stuck for 22s! [ksoftireqd/0:3] (repeats many times) SysRq : Emergency Sync (Sometimes this is the only message in the console) Others seen previously under different load situations include: BUG: soft lockup - CPU#0 stuck for 22s! [swapper/0:0] (repeated many times) or: INFO: rcu_sched detected stall on CPU 0 (t=15000 jiffies) (repeated many times with t getting bigger) From googling around I've tried various kernel parameters such as nohz=off and acpi=off to no avail. All tech support has said is that other Ubuntu installations are not suffering the same problem. Anyone got any ideas or experience with this problem?

  Read the article

< Previous Page | 598 599 600 601 602 603 604 605 606 607 608 609  | Next Page >