Search Results

Search found 16808 results on 673 pages for 'computer guru'.

Page 603/673 | < Previous Page | 599 600 601 602 603 604 605 606 607 608 609 610  | Next Page >

• Volume is no longer showing in Raid Controller BIOS and in Windows

  - by Gordon

  Hi all, I have installed some critical Windows Updates yesterday and now my external RAID Volume no longer shows in Windows Vista x64. All updates went through successfully. From their description, I cannot see how they should relate to the issue, but this is the only change that happened, so who knows. Anyway, here is the details: I have an external eSata enclosure that is running on a SiI4726 controller. I can connect to the controller with it's management utility from the computer the enclosure is connected to. The three drives in the enclosure show up as JBODs. I had those drives configured to be one logical RAID5 drive. RAID management is done through a SiI3132 SoftRaid controller. The Raid Management Utility just shows empty channels where it usually shows the Raid Group. In the Windows Disk Manager, I can see an unknown unitialized device. This is fine according to the setup manual. What it doesn't show is my Raid drive. It's gone. Also, when booting Windows, the BIOS of the controller used to show the RAID volume before booting the OS. This is not happening anymore. Updating drivers and firmware did not help. I have made sure the drivers and firmware are compatible to each others. And like I said, it used to work before. Any clues?

  Read the article

• How to use the outcome of a formula as the value for Vlookup or another IF formula

  - by Steven

  Ok I will try to explain my issue effectively. I am making a GPA sheet in which the value out of 100 is computer in to a GPA value and then in to a letter. In cell N5 i have the value of all their grades (formula: =H3+H4+H5) Now in cell (j6) I have a formula which is giving them a number depending on the value calculated in N5 (Formula: =IF(AND(N5>=60,N5<=63.999),"2.0",IF(AND(N5>=64,N5<=66.999),"2.25",IF(AND(N5>=67,N5<=69.999),"2.4",IF(AND(N5>=70,N5<=73.999),"2.5",IF(AND(N5>=74,N5<=76.999),"2.75",IF(AND(N5>=77,N5<=79.999),"2.9",IF(AND(N5>=80,N5<=83.999),"3.0",IF(AND(N5>=84,N5<=86.999),"3.25",IF(AND(N5>=87,N5<=89.999),"3.4",IF(AND(N5>=90,N5<=93.999),"3.50",IF(AND(N5>=94,N5<=96.999),"3.75",IF(AND(N5>=97,N5<=100),"4",IF(AND(N5<=59.999),"0"))))))))))))) Still no problem... as the values I was looking for comes out (example 84.2 shows up as 3.25 as I wanted). However here comes the problem.... I have tried to use the outcome in J6 to do Vlookup or another if formula, however excel does not seem to recognize the value in J6. For example: =VLOOKUP(j6,B3:C15,2,FALSE)... this returns N/A however if I enter =VLOOKUP(3.25,B3:C15,2,FALSE) it gives me what im looking for. It seems that excel will not register the outcome of my formula as a number. What can I do please?

  Read the article

• ATI Radeon 5670 Won't Show Resolutions over 1400x900

  - by Phil Sandler

  Just got my new Dell computer with Windows 7 and an ATI Radeon 5670. I attached it to my current monitor, which is a Samsung 24" (2443bwt). Windows 7 does not allow me to display in resolutions greater than 1400 x 900. The setup through a VGA cable into the VGA port of the card. The card also has a DVI port, but I need to use the VGA port because a KVM that supports VGA only. My old PC (which is Windows XP, GeForce 8600 video) can display in 1900 x 1200 on the same monitor (which is what I want) and even higher. It does this through a vga cable also connected to the KVM (through the DVI port but using an adapter). I have tried the same setup (DVI = VGA adapter) on the new PC and nothing changed. I have tried: Updating the drivers via Windows "Update Driver" (says they are current) Installing the updated version of the drivers from ATI (made no difference) Installing Powerstrip (all the options I would need for a custom resolution are greyed out) Installing the drivers/software from ATI caused the ATI Catalyst Control Center software to stop functioning, so I can no longer even start it. I have found some references to other people having this problem and instructions on cleaning the software off and reinstalling it (as uninstalling normally doesn't solve it). I will try this tonight. In any case, I didn't see any options in CCC that would allow me to override the settings for max resolution. However I didn't tinker with it too much before I tried updating the drivers, so I may have missed a setting. I contacted Samsung via online chat and they say it's a problem with the video card/driver (of course--what else would they say?). Any thoughts on what else I could try?

  Read the article

• Windows 7 - ignore security when reading external drive

  - by w-

  hi, My system hard drive on an XP computer kind of failed (random corrupt sectors). So i got a new harddrive and am trying to recover the files. The filesystem is NTFS. The system i'm trying to use when recovering the files is Windows 7. I'm obviously an admin on this box. The last data i'm trying to recover is stuff in the Documents and Settings folder. I'm using a SATA to a USB cable thingy so that I just plug it in as an External Hard Drive. The problem: In Windows Explorer when i try to copy the data, I keep getting prompted with Security warnings and error messages. It keeps telling me i have to change the owner permissions of the folder and all it's contents. If i tell it to change all the files and folder permissions it takes a really long time because it has to recurse through all the folder contents to change the permissions. Is there a way for me to ignore the file permissions when doing this? thanks

  Read the article

• VMware guest pauses when the host is idle - how do I keep it running?

  - by EMP

  I'm running VMWare Worstation 7 with Windows 7 x64 as guest, Windows XP x64 as host. Inside the guest I run a long-running console application, which prints out progress messages with timestamps on them. Sometimes I leave it running for several hours while I lock the host OS and don't touch the computer at all. When I come back I find that some time after I left it seems to have paused and automatically resumed: the console app hasn't made much progress and there's a large time gap in its progress messages. There's nothing relevant in the host event log, but in the guest Application event log I can see these messages around the time I left: A request to disable the Desktop Window Manager was made by process (VMware Tools Service) The Desktop Window Manager was unable to start because composition was disabled by a running application And later, around the time I returned, this shows up in the System log: The system time has changed to ?2012?-?01?-?12T06:36:46.921000000Z from ?2012?-?01?-?12T03:18:19.953079000Z. That seems to support my theory that it's VMware doing something and not Windows itself. The question is: how do I stop it doing that? I want my application to continue running. By the way, the power options are set to never sleep in both guest and host.

  Read the article

• Does anyone know where I could find a 2 input USB voltage meter?

  - by John O

  What we really need is a tiny UPS, of sorts. We'll be hooking up a solar cell and a battery to a single board computer. Currently, that SBC is a custom Pic32 device, and it does it's own UPS and voltage monitoring duties. I've been tasked with trying to replicate all of its features with off the shelf products... and for the most part I've succeeded. But I don't currently have any way to switch between two sources of juice, or monitor when they're getting low. These guys have something: http://www.mini-box.com/picoUPS-100-12V-DC-micro-UPS-system-battery-backup-system I really like it, the price is well within the budget. We might even work it in though it does 12V and I'll probably be using 5V... there are enough engineers on hand to figure out something. But I'd still have no idea what the voltage was for the PV or battery. I was hoping that there was some simple little USB multimeter thing that I could use to monitor this with, but I can't seem to come up with anything. I've found all sorts of cool hardware, but nothing that will help us. Does anyone know of anything?

  Read the article

• Remote Desktop leaves host unresponsive

  - by Jeff Dalley

  I have my desktop PC at home set up to accept remote connections, and I often connect to it from work on my laptop via mstsc.exe. However, every time I remote to it, I find when I go home that despite the monitor being on - it's not receiving an image and it looks as though the computer is hibernating/asleep. I basically have to restart it whenever I get home and I know there's an answer for why its doing this. More details: When exiting the remote session, I have tried both logging off the account, and closing the RDP window without logging off; both give the same result. When I get home to the desktop I of course try moving the mouse, ctrl+alt+del to see if its responsive to restart, multiple key-press to see if I can get any audio out of it; It seems pretty obvious its sleeping/hibernating in some way: Nothing happens in any of these cases and a physical restart is necessary. Both desktop and laptop are running Windows 7 Ultimate. I'm thinking it really is sleeping/hibernating it, and I'm not sure why because left alone my desktop's power options are set to never turn off the HDD or change its state - I leave it on 24/7. This could be a stupid error on my part but I just can't see it! Thanks.

  Read the article

• A switch and router between the printer and PC that want to print but cannot

  - by Robert Memo

  IP 192.168.1.5 has a wireless connection to a Linksys router (192.168.1.1) which then is connected to a switch. The switch is connected to a server (192.168.0.2). My printer has IP address of 192.168.0.8. Internet connection is fine on 192.168.1.5. Problem 1: IP 192.168.1.5 can not print using printer 192.168.0.8. Problem 2: IP 192.168.1.2 can not access a shared folder on the the server. The reason for connecting this way is that, the server does not release wireless signal. In order to get wireless signal the Router is connected to the switch. The server is a computer server that only has one outgoing LAN port. Plus, due to inconvinience physical locations, I do not have option to change the physical locations and the way it is connected already. I just want the labtops that only have wireless connection to communicate with the printer and the server. I have tried to change the router IP address to 192.168.0.x like the server and printer. It caused problem for the laptop. The router no longer release internet signals. The router does have IP address from the server 192.168.0.5.

  Read the article

• How to disable monitor auto detection in Windows 7?

  - by Jay Yother

  I am currently running Windows 7 Ultimate 64-bit with a dual monitor setup with an NVIDIA 7950 GT graphics card. One monitor is dedicated to this machine and the other monitor is connected to a DVI KVM switch. When I switch to my other computer, Windows 7 disables the monitor. However, when I switch back it does not re-enable the monitor. The only circumstance that automatically re-enables the second monitor is when I switch back after Windows has put the monitors into power save mode. I am continually having to bring up the NVIDIA control panel to have it re-enable the monitor. Under Windows XP I would just disable the NVIDIA service to prevent it from auto-detecting the monitor (which doesn't solve the problem under Win7), and in Vista there was a registry hack that would prevent this. It looks as though that has been removed in Windows 7. I have found similar questions posted on this site, but nothing that matches my problem exactly. The following link is the question that comes the closest, but does not provide a solution to the problem. http://superuser.com/questions/96683/how-to-fix-monitor-detection-on-windows-7 Is there a way in Windows 7 to disable monitor auto-detection? Update: I just added a second graphics card to my Windows 7 64-bit machine. I plugged one monitor into each graphics card. Now, when I use the KVM switch to switch back and forth it will re-enable the second monitor like it should. There are however, a few quirks with this. If I have a program maximized on the second monitor and it has focus, when I switch it will move to monitor 1. If I have a program maximized on the second monitor and it does not have focus, when I switch it will behave like it is minimized and when I bring it back up it will show up maximized on monitor 1. Definitely better than it was, but still looking for a way to disable the auto-detection.

  Read the article

• Uninstalled server 2008 now router won't handle DHCP

  - by john

  My set up is this. server behind router, router has a server and switch connected to it with multiple computers. router used to serve DHCP and DNS, a couple of days ago installed AD, DNS and DHCP on the server, and the server gave out IP's. For various reasons we had to uninstall the domain on our server. I removed AD, DHCP and DNS from the roles and set the router back to serving DHCP and DNS. Now I can't get computers on the network. I reset my router back to factory defaults, and if I plug a computer directly into the router I can get a IP address, but all the computers behind the switch can't get an IP address and can't see the router. All my computers say unidentified network, and if I ping the router it says host is unreachable. On the other hand, my wireless devices are just fine and connect no problem. But for desktops, ipconfig /release doesn't release anything and /renew can't find a server to renew on. My router log shows several FIN scans but they are from innocuous websites (google, netgear) and it shows a couple of smurf attacks but they are all from my external IP. Any ideas? the server isn't even connected to the route right now, and all the computers are set for dynamic IP addresses.. I don't know what else to try? Any help?

  Read the article

• Graphics artifacts/distortion with Win7 and nVidia

  - by Gepard

  Problem I encounter is rather hard to describe, so I provide a screenshot: http://dl.dropbox.com/u/1732760/video-distortion.png As you can see there are some horizontal stripes in random colors. These stripes appear sometimes in all windowed apps, games and on the desktop too. They tend to stay in place until I refresh window (or force it to to redraw by for example minimizing and maximizing again). They also tend to appear in the same place and shape multiple times, even if they disappear, it's very likely they will be again in the same place after a while. These artifacts do not blink or change if computer is idling. If I don't touch anything, do not use mouse, they will stay in place forever (unless some app redraws its window on its own). I first encountered this problem some weeks ago. Back then I thought it might be cooling problem, so I took out the graphics card, removed dust from the radiator and fan and put it into PC back. I also ran some stress test using Furmark (peak tempearature was ~65C) to see if the problem becomes more intense if the card gets hotter, but suprisingly no artifacts whatsoever appear during the stress test. Graphic card is Galaxy GeForce 7300 GT with DDR3 memory, was never overclocked. Drivers are the latest, from Nvidia site. OS is Windows 7 64-bit, updated. AMD64 3000+, 2GB RAM. I'm running a dual monitor setup with 2 19'' Samsung LCDs and problem is on both, so I assume it's not a monitor or cable issue.

  Read the article

• Windows won't boot after moving house. How do I solve this?

  - by James

  Ive just moved house and tried to set up my desktop after packing it away and now when I power it on, the BIOS boots up and no errors are found but when my computer tires to boot into Windows 7 a continuous fast beeping sound is made and a black screen is displayed. What I've done so far: Reset to UEFI defauts Played about with RAM, I had 4*4 GB sticks, I took all of them out to test for a mobo error which I have and now im only using 1 stick of 4 GB. Changed my GPU, I tok my gtx580 out and now im using the onboard Intel 3000 graphics driver, the BIOS and uefi are correctly displaying so I no longer think its a GPU based error. Ive check all of the connections and nothing seems to be loose. My HDD setup is: 2 128 GB SSD's in Raid 0 as my main C drive (possibly cause of error?) 1 1 TB Games drive 1 2 TB Data Drive Ive also got a blueray drive connected. After searching the internet im pretty much out of suggestions but im currently downloading a live CD to see if it will boot and if I can access some files on my HDD.

  Read the article

• Server Intermittently Inaccessible Externally (but Accessible Internally Continuously)

  - by nicorellius

  I have a CRM on a server on a network. We have a static IP and another server outward facing. We use port-forwarding to map to the CRM, so that when you go to the IP or the FQDN, you get to the CRM: xxx.xxx.xxx.xxx crm.example.com Internally, we can access the CRM by going to crm or crm.example.com Lately, I've been noticing that accessing the server from outside the network times out or gives 503, bad gateway. During that time, I can also SSH (different port, so this works) into the outward facing computer and access the server just fine. I have a robot monitoring the site and indeed via HTTP monitoring the site is going down periodically. I looked through the Apache server access and error logs and nothing stuck out at me so I'm a bit confused as to what could be going on. I also searched the access logs for 503 and found nothing. When I run tracert from outside the network, it appears the packets basically make it through the wider area servers (Comcast city and county servers) and end up dropping at the CRM server's front step. I'm tempted to replace the server because it is older and underpowered but it would be nice to know what is going on. Any ideas what to do next?

  Read the article

• 412 Precodition Failed error only occurs on certain networks

  - by Andy

  One of my favorite websites: http://jessiejofficial.com (yes, I'm a Jessie J Fan :')) has recently started displaying the error message "412 Precondition Failed" whenever I visit it from my home network, even when I use Tor Browser. At first I thought that this was an issue with the whole website, however I have contacted the web developer and he has said that they has been plenty of hits within the last 48 hours. Plus, I discovered tonight that I can access the website from my phone, through the mobile network. So it appears to just be my network as all of the devices in my house connected to the WiFi display the same error when I try to visit any page of the site. However there have been no changes that we are aware of or are noticeable to our network since the website was accessible, and I have just heard that another person in a different part of the country is experiencing the same difficulties also. Any help/advice/suggestions would be appreciated greatly Update: When trying to ping 'jessiejofficial.com' in Windows command prompt the request times out on all four attempts, on any computer connected to the wireless network. I can now also confirm that the same thing occurs on my MacBook Pro.

  Read the article

• retain last used path to location for saving files in Windows 7

  - by Mark Miller

  I am using Microsoft Office 2010 and Windows 7 on a Dell PC. I am opening a bunch of MSWord files one at a time, copying data tables therein, pasting the data into Excel and saving the Excel files as comma delimited text files. I am creating a separate Excel file for each MSWord file. The path to the folder containing the saved comma-delimited files is quite long, something like this: c:\users\me\aa\bb\cc\dd\ee\ Every time I open Excel and save a new comma-delimited file I have to re-navigate the entire path (c:\users\me\aa\bb\cc\dd\ee). In the past Windows seemed to remember the last used path, saving a lot of tedious key-strokes. In fact, I think Windows did this for me as recently as last week, albeit on a different computer. Can I apply a setting in Windows somewhere asking it to offer the last used path as a default when saving files so I do not have to re-navigate the entire directory structure to save each new comma-delimited file? If I can, how so? Where is the option for specifying that setting? Thank you for any help.

  Read the article

• what are these weird IP address connections in resource monitor?

  - by bill

  I decided to check out Resource Monitor (on the 'Performance' tab in Task Manager, Windows 7) and I noticed in the "Network" section that the 'System' image name kept making a bunch (~5 at a time) of connections to random IP addresses, it would show anywhere from 1-500 bytes/sec 'sent'. They would stay connected for 1-2 minutes. -All web browsers are closed So, first thing I did was run a trace from network-tools.com on some of these IP addresses. 8/10 were outside of US and did not resolve to any host name. Of the 10 IP addresses I traced, 2 were in US, 4 showed origins in China, and one each to Algeria, Russia, Pakistan, Korea. (!) So, the next thing I did was turn off my wireless card, watch the connections disappear, then turn the card back on, and within 30 seconds more random connections were created by System, with different IP addresses from the first time. The next thing I did was go open Task Manager, Show Processes From All Users, then I killed just about everything that wasn't (what appeared to be) a windows process. Turned on wi-fi, and again within 30 seconds, random IP addresses connect for ~ 1 min at a time, new ones coming and going. I occasionally use bit torrent on this machine, but there was definitely no process that seemed related to bt running after I went through task manager, and bt wasn't open to begin with. So, any ideas on what these connections might be for? I have been using Ad-Aware Free and AVG Free on this computer for a while now, always up to date..

  Read the article

• is there a man in the middle attacking to my server machine?

  - by GongT

  My server works well about half a year. But a strange thing happened (several hours before). This server has two IP-address 58.17.85.19 & 117.21.178.19 When I navigate to http://58.17.85.19, nothing different as before. But http://117.21.178.19 will return a "302 Object moved" and become a "redirect loop" I do some test: ($cmd = "wget http://117.21.178.19/?xx=$RANDOM --max-redirect 0 -S --no-cache -O -") Step by step: run $cmd on my PC and my firend's one (we live in two side of China, far away). - got 302 run $cmd on this server - got 200 OK (content is correct result of index.php) run $cmd on another server in same computer room - got 200 OK telnet from my PC and build an HTTP request (type by hand) - got 200 OK shutdown php-fpm, run $cmd on my PC - got 302 run $cmd on server - 502 Bad Gateway shutdown nginx, run $cmd on both the server and my PC - Connection refused. create iptables rule, refuse any connection to 58.17.85.19:80. run nc -l 80 -k -vvv on server and run $cmd on my PC NC show me that.... Server accept connection (Connection from [my ip]) My connection closed ! (Remove fd xx from list) wget dump out response - got 302 I know that, normaly, NC will accept connection, then dump HTTP request from client, and client will wait for response. this connection will open forever(infact client will close connection becouse timeout), becouse NC can't give any response. So... where my request gone? who send an response to the client? some virus on my server system? If so, why 58.17.85.19 didn't has this error? or... I was attacked by a middleman?

  Read the article

• OS X Application icons missing after filesystem tampering

  - by dylan

  A while back I installed some Google software, I forget what it was, but it was something that attached itself to Google Chrome and was un-uninstallable short of uninstalling all of Chrome. It was a total pain in the a$$. Anyways, I was trying to put up a fight before going nuclear and just wiping Chrome, and during that fight, something went wrong (i.e., I didn't know what I was doing). I remember messing around with the Applications folder somehow. I don't remember what exactly I did, but it perhaps involved some interchanging between the /Applications and /User/Username/Applications folders? Definitely some tampering in those areas, I'm sure at least about that. Anyways, I've since updated and restarted my computer. Now, while all my apps work fine, many of them have blank icons - not on the Dock, those icons are fine, but in Spotlight search results, etc. Currently, my /Applications folder contains only OS X-cooked-in applications. My ~/Applications folder contains cooked in apps AND post-OS/third-party apps. There hasn't been any functionality deficit so far, but I don't like working on a machine where something isn't how it should be. I know my information was vague, but does anyone know what went wrong / how to fix it? OS X Mavericks 10.9.3

  Read the article

• 2 routers at home- how to connect with VNC?

  - by Charles Leviton

  I have two routers at home. First router is upstairs and is connected to the cable modem. 2nd router is downstairs and acts as "signal booster" for the 1st router. Devices connected to the upstairs router have IP addresses of the form 192.168.1.n Devices connected to the upstairs router have IP addresses of the form 192.168.2.n. I blindly followed instructions from a website to do this set up, just glad it works! Upstairs I have a PC running Win 7 64 bit. Its assigned IP is 192.168.1.7. I have a VNC viewer running on this. Downstairs I have a 2nd PC running Vista 32 Home edition bit that is connected to the 2nd router and has IP Address 192.168.2.114. VNC server is running on this. It's listening on 5900. There is no firewall. When I try to connect to this downstairs PC from upstairs it fails with message "Failed to connect to server". I cannot ping to this either. If I try to connect to this downstairs PC using VNC Viewer from another computer that's connected to the same downstairs router then it works like a charm. So what's the work around if the viewer is on a different "network"? I don't have any problems doing remote desktop connection from the downstairs PC to the upstairs PC even if they are connected to different routers. Router information- Upstairs- ASUS RTN13U, downstairs- DD-WRT v24 RC-5 Thanks! P.S. I posted this on the Ultra VNC forum as well but that doesn't seem to have a lot of activity, so taking the liberty to multipost.

  Read the article

• Made a .dmg for a project; user can't open it - "no mountable file systems"

  - by dragonridingsorceress

  Hello, We don't know a great deal about Macs. We had to make an installer, and were told to try a .dmg So we put together version 1, and it seemed to work. We had one application file, which had our icon, and one folder. The user was instructed to drag these into the Applications folder, of which there was the Mac version of a shortcut in the dmg. Then we were told we needed to update files, and assured that we could do so via drag-and-drop. So we did; we dragged them into the folder in the dmg. We tested it (on the computer we were using to edit the dmg) and it seemed to work. So we burnt it onto a disk (along with a windows installer that actually works!). I've just gotten an email from the recipient. She's got a Mac laptop. She inserted the disk, doubleclicked on it, doubleclicked on the .dmg, and got a Warning: no mountable file systems. Screenshot: http://www.flickr.com/photos/97292258@N00/5101670174/ I have the dmg (not on a disk) and am able to open it with no difficulty. How can we get it to work for our recipient?

  Read the article

• Are email addresses mandatory for Windows 8 login names?

  - by Cedric Martin

  I've got a computer running Windows 8 and in the user accounts I can see four accounts (they're in french, here's a rough translation): [email protected] / administrator Veronique YYY / [email protected] ASP.NET Machine Account / local account guest account / the guest account is desactivated I've got several questions but they're all related to email addresses and login names / accounts. Are email addresses mandatory for Windows 8 login names? Can you mix live and non-live user accounts on a Windows 8 system? Is it possible to have a live Windows 8 user account which is not using a @live.xx email address? Is it possible to have a non-live Windows 8 user account which is using a @live.xx email address? If the gmail.com email address of the admin is not a live Windows 8 account, does this mean I can create a "fake" email and use that as the email of a new Windows 8 account? Basically I don't understand very well why there are email addresses displayed on the login screen and why there are both @live.xx and @gmail.com email addresses on the same system and answer to the questions I asked above may help me understand a bit better what is going on (I'm coming from a Linux / OS X background. I literally haven't used Windows in more than a decade).

  Read the article

• quad sli with gtx 690 not working

  - by Moaadh

  I have two cards GTX 690 (dual core). I did the Sli successfully. Nvidia control panel acknowledges the two cards as quad Sli. However, the problem is that Windows 7 64-bit Ultimate is showing me the graph memory size as 4 GB while it is supposed to be 8 GB because of the Sli. Also the benchmark from all software is giving me a very low score compared to some other guy's benchmark on YouTube. It gives me a big headache. Does anyone know why this is happening? If so, how can I get Windows 7 to recognize all 8 GB of memory? Thanks for your help in advance. My computer specifications: (Processor: Intel Core i7-3930k @3.2GHz(12CPUs))--- (Memory: 65536 MB Ram 1866 MHz)-- (OS: Windows 7 Ultimate 64-bit)-- (OCZ 240GB as SSD PCIe drive for booting and storage disk)-- (DirextX version: DirectX 11)-- (VGA Card: 2 X EVGA GTX 690 Dual GPU. Each GPU is 2 GB, so total memory should be 8 GB.)-- (MotherBoard: ASUS Rampage IV Extreme)-- Others with lesser specifications get a 2500 score in heaven benchmark while I get 1501 as if it is one card.

  Read the article

• After RAID failure SBS 2008 issues logging in and Exchange store does not mount

  - by Josh R

  today has been one of those days. Yesterday a hard drive in our Dell Poweredge 2900 server failed and the RAID array didn't degrade gracefully, so I called Dell (Server still under warranty) and got an engineer to work though the RAID issues with me. He was a nice guy but didn't do too much. We tried to put the RAID in a state where it was bootable and even though we only lost one disk there are still issues with the server. Once we got the server to boot there was an error message saying that the logonui.exe was corrupted and we needed to run chkdsk. I clicked through the error messages and the login screen never came up. So I power cycled the server and it chkdsk automatically but the login screen didn't appear. I tried safe mode, no difference there either. So the issues I am currently having are: 1) The server boots up, the loading windows screen comes up then it dumps me into a black screen where I can only see my mouse cursor. Ctrl+Esc doesn't work Ctrl+Alt+Del doesn't work 2) Some of the services come up: DHCP, DNS, DFS, and Print come up 3) The exchange information store and transport service don't start - I tried using mmc to connect to services.msc on the computer and start them but they throw an error message of "Can't start because group or dependency failed" Has anyone had a problem like this? Can anyone offer some guidance? Thanks a bunch!

  Read the article

• Stop Windows 7 from accessing or writing to hard drive unless "told" to by me? (More info inside...)

  - by Jeff

  A confusing question, perhaps, but bear with me. I have two internal HDDs set up in a RAID0 array which I use as mass storage. I access the drive very infrequently (once a day at most) and so I have set up Windows 7's power options to turn off idle disks after only 1 minute. This is fine, and the disks are turned off most of the time. However, I notice that Windows sometimes spins up the drives when I really, really don't want or need it to. This causes a 30 second delay as both drives spin up and lock up my system. Some examples of when this happens: 1) When I'm installing something using Windows Installer or Installshield; it seems to me as if they're using the drive with most available free space as the installer cache location... so my big RAID drive has to spin up! Most annoying. 2) Apparently, when I open a Java-based program which resides on my system drive and has nothing to do with my RAID drive! 3) At boot-up and shut-down time. At shutdown the drive spin up only for the computer to immediately shut down! Incredibly frustrating! I've already tried changing the letter of the drive, and at some points have removed the drive letter entirely, which solves the first two issues above. So my question (FINALLY!) is this: is there any way I can mark this drive as being for "storage only", so Windows basically does not see it at all until I actually invoke it somehow? Or is there any way I could set it up so that only specific programs have write access to it? For example, download managers, TeraCopy, etc. etc.? Basically I want it to be a "ghost drive" until I'm ready to use it and to stop Windows from spinning it up all the damn time! Thank you. :)

  Read the article

• Drive security settings in Windows 8 Pro

  - by Donotalo

  My PC OS is Windows 8 Pro x64. Windows 8 seems confusing. D:\ drive is supposed to be used solely by a single user, who is in Users group of the PC. The requirement is... that user will have full control of D drive. Admins will have full control of D drive. All other users can only list drive contents. No file could be opened. My account is admin account. From D drive's property Security tab, I've set the following: Allow "List folder contents" for Authenticated Users group. Allow "Full control" for SYSTEM. Allow "Full control" to specific user, who's supposed to use the drive. Allow "Full control" for Administrators group of the computer. Allow "List folder contents" for Users group. After setting this up, the specific user have full control of D drive. No other user can open any file on D drive. But though my account is an admin account, no file on D drive could be opened from my account! Why is this happening and how files can be opened from my account? Note: All accounts in this PC are local accounts.

  Read the article

< Previous Page | 599 600 601 602 603 604 605 606 607 608 609 610  | Next Page >