Search Results

Search found 46833 results on 1874 pages for 'distributed system'.

Page 605/1874 | < Previous Page | 601 602 603 604 605 606 607 608 609 610 611 612  | Next Page >

• Will my RAID0 stay intact when I move it to a new computer?

  - by Jeremy H

  My primary drive is a 250GB WD SATA drive. So, I added 2x 500GB 7,200 RPM WD SATA drives into my Windows Vista box and created a 1TB RAID0. I then formatted the the primary drive and installed Windows 7. To my pleasant surprise when I booted into Windows 7 my RAID0 was still intact and I kept trotting along the same as I did before. Now I am replacing my motherboard, processor, and RAM and plan on formatting the primary 250GB drive again and using it to boot for a new clean install of Windows 7. My question is: if I move these two SATA drives which are setup for RAID0 into the new system, install Windows 7 again, will the RAID0 remain? Edit: Software RAID. I created it within Windows. The RAID0 does NOT contain the system boot partition.

  Read the article

• "Disk boot failure" error after installing Windows 7 on SSD

  - by Tony_Henrich

  I have a system with 3 SATA drives which runs fine. Got a new SSD drive and wanted to install a fresh Windows-7 on it. So I removed the boot drive and replaced it with the SSD drive. Installed Windows and when it was done, rebooted and now I get "Disk boot failure. Insert system disk and press enter" error message. I reinstall again and still same message. Removed the SSD and put back the original drive and I got the same message!! I checked the BIOS and things look good. Something is wrong. Two questions: 1- Why isn't the new Windows booting from the SSD? 2- Why isn't the machine booting using the previous working configuration anymore, after removing the SSD? I did connect it during the second Windows installation but it was the last drive in the SATA connector. Would Windows installer mess with its MBR sector?

  Read the article

• ATI Radeon Drivers works with which linux distribution and version? [closed]

  - by amit.codename13

  I have ATI Mobility Radeon HD 5850 graphics card. Almost every new linux distribution seems to have an issue with it, when i install the drivers. Working without utilizing the graphics card leaves me so unproductive. So i made a plan to use older versions of linux, any distribution suitable as a desktop distribution. The problems that i am facing are, 1) After installing drivers the system boots and hangs, 2) There are unusual lines over the screen 3) After upgrade system doesn't start properly(hangs the usual old way) The kind of answers i am looking for is, distribution X(the newer the version the better) doesn't have the above problem after installing drivers for ATI Mobility Radeon HD 5850 graphics card. UPDATE: The new drivers released by AMD seems to fix all the issues, although they are still beta

  Read the article

• Exchange Server 2003 Drive Error

  - by Saif Khan

  My exchange box went offline this AM. The logs show The device, \Device\Harddisk1, has a bad block. I tried running chkdsk D: /x /r but that didn't help either. I went to the Exchange Manager and tried to move the .stm file from D: to C: but got Exchange System Manager The database files in this store are corrupted. ID no: c104173b Exchange System Manager What else is there to try just to get this online for a few hours until I can get onsite to change the drive. This is a Windows Server 2003 server.

  Read the article

• Where does truecrypt store the backup volume header?

  - by happygolucky

  When using WDE, where does (if anywhere) truecrypt store a backup volume header? As i know there is always a backup header for regular truecrypt volumes, however i am not sure if this applies when system encryption is used. Because if i damage the volume header in track 0, my password won't boot my system anymore. So there is no backup header on the drive? I read somewhere on a forum that truecrypt might have a backup header relative to some position from the END of the HDD, however this doesn't make sense as it could easily be wiped over by programs running in Windows. And how would truecrypt know where this backup is anyway?

  Read the article

• consulting a network admin for rails and php applications

  - by Karo Devos

  Hi I'm a web developer who writes most of the time rails applications. Next month I'm going to switch from my current VPS to linode. I'm wondering how much it would cost to properly set (or teach me how to do it) everything to get my app up and running. My requirements are probably: nginx/apache, REE/ruby, passenger, full blown php environment, system wide RVM, search engine such a sphinx, being able to perform cronjobs. I have some knowledge of unix and I was able to install everything I needed on my development system. However I had quite a few issues setting up everything on my production server.

  Read the article

• Mac OS X change IP configuration automatically by location (by Wifi network)?

  - by Seppo Sade

  Can Mac OS X be setup to automatically configure its Airport interface with a static IP address when connected to a Wifi network with a certain name, and on all other Wifi networks use DHCP? Currently I'm using the "Locations" feature of the "Network" section in System Preferences to manually switch between two IP address setups. I have a "my static IP" setup, and a default "DHCP" setup. However this requires entering System Preferences to change the Location drop-down each time when switching locations. Can this be automated? Preferably this would be done without third-party software.

  Read the article

• "Cannot allocate memory " error whle copying data from window to ubuntu

  - by John

  I have Ubuntu 9.10 installed inside VM of server 2008. WHen i try to copy the data from the network and paste insid ethe Ubuntu it says error called "Cannot allocate memory " I have 3GB RAM attached to the Ubuntu I tried above suggestion but still im unbale to copy file from my host machine i.e. Windows XP to my Ubuntu machine ( which is at Virtual Machine) Im trying to copy jdk-1_5_0_22-linux-i586.bin file whose size is 47.4 MB Is there any other work around for this problem???? I tried Set the following registry key to ’1': HKLM\SYSTEM\CurrentControlSet\Control\Session Manager\Memory Management\LargeSystemCache and set the following registry key to ’3': HKLM\SYSTEM\CurrentControlSet\Services\LanmanServer\Parameters\Size but still im unbale to copy file from my host machine i.e. Windows XP to my Ubuntu machine ( which is at Virtual Machine) Im trying to copy jdk-1_5_0_22-linux-i586.bin file whose size is 47.4 MB Is there any other work around for this problem????

  Read the article

• Adding a web folder via command line (Windows)

  - by Ryan

  I am trying to add a web folder via command line in windows. At first I though I should use the "net use" command, but when I tried I kept getting System error 67: C:net use * http://dev.subdomain.domain.tdl/dav/ the user name for 'dev.subdomain.domain.tdl': correctusername the password for dev.subdomain.domain.tdl: System error 67 has occurred. The network name cannot be found. The url I used works in a browser. It's an Apache dav on basic auth LDAP authentication method being used. Here's the thing... I CAN create a web folder when I use the "Add a network place" wizard. When I do net use, I don't see it listed in the prompt that follows. What utility do I need to use to mount a web folder in command line?

  Read the article

• scsi and ata entries for same hard drive under /dev/disk/by-id

  - by John Dibling

  I am trying to set up a ZFS pool using 4 bare drives which I have attached to my Ubuntu system via a SATA hot swap backplane. These are Hitachi SATA drives. When I list the contents of /dev/disk/by-id, I see two entries for each drive: root@scorpius:/dev/disk/by-id# ls | grep Hitachi ata-Hitachi_HDS5C3030ALA630_MJ1323YNG0ZJ7C ata-Hitachi_HDS5C3030ALA630_MJ1323YNG1064C ata-Hitachi_HDS5C3030ALA630_MJ1323YNG190AC ata-Hitachi_HDS5C3030ALA630_MJ1323YNG1DGPC scsi-SATA_Hitachi_HDS5C30_MJ1323YNG0ZJ7C scsi-SATA_Hitachi_HDS5C30_MJ1323YNG1064C scsi-SATA_Hitachi_HDS5C30_MJ1323YNG190AC scsi-SATA_Hitachi_HDS5C30_MJ1323YNG1DGPC I know these are the same drives because I wrote down the serial numbers, and all the other drives in this system are either Seagate or WD. The serial number for the first one, for example, is YNG0ZJ7C. Why are there two entries here for each drive? More to the point, when I create my ZFS pool which one should I use; the scsi- one or the ata- one?

  Read the article

• How do I know when my on-board ethernet is dead? (Realtek 8112L LAN controller w/ AI NET2 )

  - by Usagi

  So I have an ASUS P7P55D-E Pro motherboard. It has an on-board Realtek 8112L LAN controller w/ AI NET2. I suspect that my LAN controller is dead but I don't really know for sure. This is what I know thus far: Everything was working, I have a triple booted system and ethernet was functional under Linux, Win7, and OSX. My ethernet is no longer functional under all three of the operating systems. I was experiencing random momentary internet outages before everything finally went dark. I don't know much about the AI NET BIOS tool but I believe it just checks for ethernet problems before you boot into an operating system. In any case, it doesn't find a connection upon boot. I've checked the connection on a couple of other machines and everything worked fine. I think I already know the answer to my question, but are there any other possible explanations, or is it dead?

  Read the article

• water cooler fan in my computer room............

  - by metal gear solid

  Is using water cooler fan in my computer room HARMFUL for the internal parts of the computer system?

  Read the article

• Somebody knows why the sectors of the IBM floppy disk are named 1 to 8 (and not 0 to 7 )

  - by Olivier Briand

  I am now programming on a 8 bits Z80 computer with CP/M 2.2, (as a hobby) and the floppy disk format is IBM, 40 tracks, 8 sectors per track, 512 bytes per sector. free space is 154 Ko on each face of the disk. Why the sectors are indexed 1 to 8 (and not zero to seven, as usually is seen with computers)? The catalog of the floppy disk is on the track 1 (sector 1 to 4, 64 entries). I'm wondering is the catalog on track zero? Is the zero track reserved to included a system (as track 0 & 1 are reserved to the system on a CP/M floppy disk, and catalog is on track 2)?

  Read the article

• How to stop LDAP authentication in ubuntu?

  - by Kery

  My OS is Ubuntu 12.04 and use LDAP authentication. Now I meet a problem that another people want to access my system. But he is in another domain so he can't login. And I have no right to change this configuration in LDAP server. So I have to choose a workaround to solve this problem, for example close the LDAP authentication and use local authentication (I have root right in my system) or create another account which is not registered in LDAP server (I did this but can't change the created account password. The error is 'password reset by root is not supported'). Of course any other suggestion is appreciated! Than you in advance!

  Read the article

• 5 x 3GB drives and 4 x 1500GB drive best raid setup?

  - by Zen_Silence

  Hello, I am building a file server my plan is the have the Operating system on one raid partition and the data storage on another partition. I currently have 5 x 3GB IDE drives that i would like to put the operating system on theses drives are old but that doesnt matter to me at the moment i have a ton of them so for this raid partition i would probably want to be able to pull out dead a drive and rebuild the array. My file partition is going to consist of 4 x 1.5TB SATA drives I would like the maximum storage with some redundancy. Any suggestions to which Raid level i should use would be greatly appreciated and if you could also suggest a PCI or PCI-e raid controller to handle theses arrays. Thanks in Advance, Zen_Silence

  Read the article

• OOF (Out of Office) is not working for remote users (Outlook Anywhere)

  - by Doughecka

  I'm not sure how long this issue has been happening, but recently a few of the remote sales users were going to a sales meeting and wanted to set their Out of Office... however in Outlook 2010, they get this error message: "Your automatic reply settings cannot be displayed because the server is currently unavailable" When I run the Exchange Remote Connectivity Analyzer, Autodiscover completes fine, but the next step fails: Exception details: Message: The request failed. The remote server returned an error: (403) Forbidden. Type: Microsoft.Exchange.WebServices.Data.ServiceRequestException Stack trace: at Microsoft.Exchange.WebServices.Data.ServiceRequestBase.GetEwsHttpWebResponse(IEwsHttpWebRequest request) at Microsoft.Exchange.WebServices.Data.MultiResponseServiceRequest`1.Execute() at Microsoft.Exchange.WebServices.Data.ExchangeService.BindToFolder[TFolder](FolderId folderId, PropertySet propertySet) at Microsoft.Exchange.Tools.ExRca.Tests.EnsureEmptyFolderTest.PerformTestReally() Exception details: Message: The remote server returned an error: (403) Forbidden. Type: System.Net.WebException Stack trace: at System.Net.HttpWebRequest.GetResponse() at Microsoft.Exchange.WebServices.Data.EwsHttpWebRequest.Microsoft.Exchange.WebServices.Data.IEwsHttpWebRequest.GetResponse() at Microsoft.Exchange.WebServices.Data.ServiceRequestBase.GetEwsHttpWebResponse(IEwsHttpWebRequest request) I've done some research, but I have yet to find a working fix for this... it seems like some permissions are messed up in IIS, but I haven't figured out what.

  Read the article

• Windows XP Home Adobe.Com folder trying to install twice

  - by John Martinez

  Twice I had to reinstall because Adobe 9 installed for a second time without me requesting or being asked to. There is a Adobe folder and an Adobe(2) folder. Installed were Adobe.com; AIS; Reader 9 and Active X. The system crashes. I can't do anything. In safe mode, can't uninstall or system restore. Can't click on anything in regular environment. Not only will I start looking for alternative pdf reader, and if I can't view a site without active X so be it. But if I do decide to re-install Adobe, HOW DO I CONFIGURE IT TO NOT UPDATE AUTOMATICALLY???? Day and a half to re-install everything.

  Read the article

• suggest AMD machine for software developement [closed]

  - by superb1

  I need a AMD machine (Processor, Motherboard, Ram, HDD ) for software developement .. I will mainly use microsoft visual studio 2010. Operating system would be windows 7 . Suggest decent machine but i dont want to overspend....i guess the rating system of ecommerce websites may help you to suggest !? I want you to suggest from this list : http://www.flipkart.com/computers/components/processor-20246?ref=bae2643a-2cc8-4710-942f-79e7fbc1b416 plz note basic criteria for vs 2010 is 1.6GHz or faster processor 1 GB (32 Bit) Ram 5400 RPM hard disk DirectX 9 capable video card running at 1024 x 768 or higher-resolution

  Read the article

• Enlarge partition on SD card

  - by chenwj

  I have followed Cloning an SD card onto a larger SD card to clone a 2G SD card to a 32G SD card, and the file system is ext4. However, on the 32G SD card I only can see 2G space available. Is there a way to maximize it out? Here is the output of fdisk: Command (m for help): p Disk /dev/sdb: 32.0 GB, 32026656768 bytes 64 heads, 32 sectors/track, 30543 cylinders, total 62552064 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000e015a Device Boot Start End Blocks Id System /dev/sdb1 * 32 147455 73712 c W95 FAT32 (LBA) /dev/sdb2 147456 3994623 1923584 83 Linux I want to make /dev/sdb2 use up the remaining space. I try resize2fs /dev/sdb after dd, but get message below: $ sudo resize2fs /dev/sdb resize2fs 1.42 (29-Nov-2011) resize2fs: Bad magic number in super-block while trying to open /dev/sdb Couldn't find valid filesystem superblock. Any idea on what I am doing wrong? Thanks.

  Read the article

• Getting Started with windows server 2008/2012

  - by hbrock

  First let me say, I am a programmer(not a super star) but I want to get more into the system/network administration side of things. This because there are more jobs for system/network administrators in the area I live. Right now I am using virtual machines to learn how windows 2008/2012 works and to build labs with. But how would I prove to an employer what my skill set is with windows 2008/2012? As a programmer I would point to my past projects, code samples, and so on. Thanks for any help.

  Read the article

• Config Time Service on Server 2008 DC using Group Policy Only

  - by Ed Fries

  I want to configure the Time Service using only GP in a Server 2008 R2 domain. I have created a GP as follows: Computer Config, Policies, Administrative Templates, System, Windows Time Policy: =Global Configuration Settings -Enabled w/ default settings. Computer Config, Policies, Administrative Templates, System, Windows Time Policy,Time Providers: =Configure Windows NTP Client -Enabled w/ default settings. =Enable Windows NTP Client -Enabled w/ default settings. =Enable Windows NTP Server -Enabled w/ default settings. The policy is linked, enforced and applied to Domain Controllers OU. The GP modeling results shows the policy is in effect on the DC (Single DC domain) and the DC is recognized as the PDC emulator. I have run gpupdate /force and logged off/on. The issue is that the DC shows the time source as internal. I understand I can force this at the cmd line using w32tm to set the peer but I would like to understand what is missing in the GP. The default NTP Client GP setting includes time.windows.com,0x9 as the source but it does not appear to be taking effect.

  Read the article

• Prevent Windows 7 from unpluging External HDD [migrated]

  - by marverix

  I have installed Windows 7 as my media server. I pluged in 500GB external HDD via USB. I have changed power plan to Best Performance and changed advenced power settings to never turn off HDD etc. I even yesterday wrote powershell script (create and delete folder on this disk) and I have added it to harmonogram to run every 5 minutes starting from system boot. And nothing! Disk after some time (I realy can't say when) is turning off and Windows show "Unknown Device" in Device Manager. Then only system reboot or disk reboot helps. Any ideas how to prevent Windows 7 from stopping my external HDD? Cheers!

  Read the article

• Clarification of the difference between PCI memory addressing and I/O addressing?

  - by KevinM

  Could someone please clarify the difference between memory and I/O addresses on the PCI/PCIe bus? I understand that I/O addresses are 32-bit, limited to the range 0 to 4GB, and do not map onto system memory (RAM), and that memory addresses are either 32-bit or 64-bit. I get the impression that memory addressing must map onto available RAM, is this true? That if a PCI device wishes to transfer data to a memory address, that address must exist in actual system RAM (and is allocated during PCI configuration) and not virtual memory. So if a PCI device only needs to transfer a small amount of data at a time, where there is no advantage to putting it into RAM or using DMA, then I/O addressing is fine (e.g. a parallel port implemented on a PCI card). And why do I keep reading that PCI/PCIe I/O addressing is being deprecated in favour of memory addressing? Thanks!

  Read the article

• Build Advise for Home Web/NAS Server with Ubuntu Server 12.04 [closed]

  - by razor7

  I need to have a personal Webserver with NAS capabilities. The Webserver to test some LAMP projects I develop for clients, and also NAS to be able to stream media to local network. I want to have full control of the box, so I'm planning to build it with some spare parts and Ubuntu Server. The services/software that will run are (remember, is for personal and testing use only): SAMBA/CIFS SSH Server Apache 2 MySQL 5 Mercurial Repo PHP 5.3 Ruby on Rails OwnCloud Dovecot Webmin Postfix PureFTPd ClamAV The Hardware: Intel Dual Core E2180 2.0 GHz MSI P35 Neo Kinkston 1GB DDR2, 667 MSI Nvidia 7300le PCIe x16 256mb RAM HDD SATA WD Green 2TB x2 (RAID-1 with MDADM RAID Controller) 16 GB USB Pendrive (For server system installation) My idea is to build this system, using the pendrive for the Ubuntu Server software, and packages, and the RAID-1 for gross data storage. What do you think? Thanks a lot!

  Read the article

• Installing OpenVPN on Windows7

  - by Darcara

  It seems I cannot install the current version of OpenVPN (2.1.2) because the TAP driver is not signed and therefore windows 7 x64 refuses to install it. It shows up in the device manager, but with a yellow exclamation mark. It's a fresh system, and OpenVPN was never installed before. When I start the OpenVPN client it seems to connect fine, but then it stops with CreateFile failed on TAP device: ... All TAP-Win32 adapters on this system are currently in use. How can I install the unsigned drivers, or are there signed drivers available somewhere ?

  Read the article

< Previous Page | 601 602 603 604 605 606 607 608 609 610 611 612  | Next Page >