Search Results

Search found 30270 results on 1211 pages for 'bart read'.

Page 606/1211 | < Previous Page | 602 603 604 605 606 607 608 609 610 611 612 613  | Next Page >

• RSync over SSH - permission denied even though the user is in the root group

  - by Bastien974

  I have a need to copy files between servers through the web. I'm using RSYNC over ssh to do so. The problem is, I need to be able to transfer files, no matter where the files is. I created a user rsync and : usermod -G root -a rsync to give him the right to read/write anywhere on both servers. During the transfer, I see this error: rsync: mkstemp "/root/.myFile.RDr2HY" failed: Permission denied (13) I don't understand what's happening. edit: I just found out that the destination folder didn't have the write access for the root group. How would I give 100% access to this rsync user ? If I change its uid to 0, rsync stop working.

  Read the article

• Converting text file to epub?

  - by jamesh

  I have a bunch of book length text files I'd really like to read on my EPUB reader (as it happens FBReaderJ). What would be the best route to convert them? I have access to OSX and Linux (Ubuntu). Probably happiest with a command line, but would setting for a GUI for batch conversion. My criteria for success are really based upon the shortfalls I have found with Calibre must do the whole book at least a guess of what the title/author may be. Minimum the source filename for the title. hygienic with files it uses - tidies up after itself (this is less important) doesn't try to be an all-in-one library manager (again, less important). is lenient in parsing special characters (e.g. < and & characters).

  Read the article

• x11vnc is slow, but using only 10% of available bandwidth

  - by mmm

  I am using x11vnc over 15Mbit/s network with 20ms latency. When the screen is changing a lot x11vnc is slow - for example when I switch a tab in a browser, it takes almost two seconds until the view is fully redrawn. The strange thing is that max connection speed of x11vnc is even during slow redrawing only about 10% of the available bandwidth. Why is x11vnc not using available bandwidth to speed the redrawing up? For example scp is using 100% of available bandwidth without problems. How can I identify what is the bottleneck for x11vnc on my system? So far I think: 10% network usage = network is not a bottleneck fb read rate: 601 MB/sec = reading fb is not a bottleneck Any ideas how can I further profile x11vnc and find out what is causing a slowdown? For example is there any switch for x11vnc to show how much data it is handling and how long it takes to grab a screen, process and compress it and send it over the network?

  Read the article

• Why is a ZFS pool not persisting over server restart?

  - by Chance

  I have a ZFS pool with 4 drives. It also has a 3gb ZIL and a 20GB L2ARC that are each partitions on an SDD that doubles as my Linux Mint (ver. 13) boot drive. The pool is mounted to /data. The problem I am running into is that when I restart the server the pool/directory is completely wiped despite having data in it prior. I'm afraid I'm doing something wrong in the setup, which leads me to the following questions: What would cause this? Is there anyway to get the data back? How do I stop it from happening in the future? Thank you in advance! pool: data state: ONLINE scan: none requested config: NAME STATE READ WRITE CKSUM data ONLINE 0 0 0 raidz2-0 ONLINE 0 0 0 sda1 ONLINE 0 0 0 sdb1 ONLINE 0 0 0 sdc1 ONLINE 0 0 0 sdd1 ONLINE 0 0 0 logs sde4 ONLINE 0 0 0 cache sde3 ONLINE 0 0 0 errors: No known data errors

  Read the article

• Remote file access.

  - by Rob Rob

  Hi, We're needing to provide remote (read/write) access to a number of files on our network to several users (some technical, some non-technical) who will be running Windows. The non technical users will need to be able to access their files in an easy to use manner. From previous experience, we could do this with: (some sort of) VPN SSH and something like Dokan (i've only previously done this on linux with sshfs) WebDav FTP VPN and SSH access are more open that we need at present, so I'm leaning towards webdav, however I only have limited experience of it (setting up an SVN server several years ago), but my understanding is that users can access it through windows explorer. FTP I haven't had much experience of, as I've always used SFTP via ssh - but i'd imagine we could make this work in a similar way to ssh. So my question is - have I missed any obvious candidates for this task, or if webdav is (or isn't) suitable what are the security implications of using it for this (obviously https will be used for the transfers, etc). Thanks, Rob.

  Read the article

• How to share media stored in an attached drive using Windows Media Player?

  - by David

  We've got a Windows 7 PC with a Windows Media Player music library that includes both files on the internal hard drive and files on a USB-attached hard drive. When we browse this library from another Windows Media Player (on another Windows 7 machine) we see only the files residing on the library host's internal drive. The files residing on the attached drive don't show up at all, yet on the host they appear undistinguished within the library. Is there a configuration change we can make to cause the attached files to be shared properly? We've turned on read-sharing for "Everyone" on the USB drive, but that hasn't helped. Also it might be worth noting that this issue behaves the same way for us if the client machine is a Playstation 3.

  Read the article

• Why are they putting "processors" on hard drives?

  - by Celeritas

  What does it mean when they have a processor on the hard drive, how does it work, and what benfit does it have? I don't understand - the CPU is the processor and the hard drive transfers it's contents to RAM. Do have additional processors, preprocess the data some how? Here's some examples Western Digital WD Black WD1002FAEX 1TB "Dual processor speed" NETGEAR ReadyNAS 312 2-Bay Diskless Network Attached Storage "Dual-core Intel 2.1GHz processor and 2GB on-board memory" and routers now have processors too, why's that nescecary? I guess it sort of makes sense - some logic needs to happen for the packets to be read in to know which ports to send them out on, but why did old routers not need them? Example or wireless router with processor: "Dual-core processor"

  Read the article

• Best way to create a common folder when creating new users that is a drop box, readable and writeable by all users

  - by Michael Prescott

  What is the best way to provide a common drop box for all users, so that any user that is a part of a particular group can read and write to and from the directory? I thought of creating a directory outside of the /home directory, creating a group specifically for accessing the directory, then adding all desired users to that group, and finally adding a symlink to the home directory of each user that points to the drop box folder. That seems like a lot of work. Is there a better way? I'm running ubuntu 10.04 LTS.

  Read the article

• Restore XP on Acer Aspire One netbook

  - by Imran

  I have an Acer Aspire One D250 netbook which came with Windows XP (but no CD) on which I have since installed Xubuntu 9.10. Now I am trying to sell it, but I cannot find a way to recover XP. I have read in a lot of different places that holding Alt+F10 during boot should send me to a recovery menu (which will allow me to restore XP from a "secret partition"), but I have tried many times to no avail. The best I can do is get the BIOS setup screen by holding F2, but there doesn't seem to be any recovery option there. After the initial option to go into the BIOS setup GRUB starts loading and there don't seem to be any more opportunities to enter a system setup screen. Please help!

  Read the article

• Internal only DNS?

  - by ethrbunny

  We are running a research project with hundreds (becoming thousands) of remote hosts. Each host is running OpenVPN so we can find them regardless of what their 'assigned' IP is. We have been using DynDNS to manage this but we're running into some issues with them ( API is weak/nonexistent, size constraints, etc). Im looking into setting up a internal-only domain (EG "our.stuff" so a host would be "site1.our.stuff" or "site3.net4.our.stuff") that I can configure with the info from the OpenVPN server. Since we'd have to point our internal DNS to this machine it would have to be able to route/cache requests for 'external' machines as well. I've been trying to read about 'internal DNS', 'private', 'non-routeable' but I'm not having much success. Summary: need info on internal, caching DNS server. Something with open-source would be ideal. If not, I can script out changes to .conf, etc.

  Read the article

• Server side rules in Outlook 2007

  - by AngryHacker

  Using Outlook 2007 with an Exchange Server. I am trying to setup a server-side rule, but regardless of what I do, it always sets up a client-only rule. I am trying to copy a message to a folder if it comes from a certain person and the subject contains certain words. What am I missing? Update: It seems that setting the rule to mark the message read-only forces the message to be client-side. Anyway to get around that?

  Read the article

• How can I enable anonymous access to a Samba share under ADS security mode?

  - by hemp

  I'm trying to enable anonymous access to a single service in my Samba config. Authorized user access is working perfectly, but when I attempt a no-password connection, I get this message: Anonymous login successful Domain=[...] OS=[Unix] Server=[Samba 3.3.8-0.51.el5] tree connect failed: NT_STATUS_LOGON_FAILURE The message log shows this error: ... smbd[21262]: [2010/05/24 21:26:39, 0] smbd/service.c:make_connection_snum(1004) ... smbd[21262]: Can't become connected user! The smb.conf is configured thusly: [global] security = ads obey pam restrictions = Yes winbind enum users = Yes winbind enum groups = Yes winbind use default domain = true valid users = "@domain admins", "@domain users" guest account = nobody map to guest = Bad User [evilshare] path = /evil/share guest ok = yes read only = No browseable = No Given that I have 'map to guest = Bad User' and 'guest ok' specified, I don't understand why it is trying to "become connected user". Should it not be trying to "become guest user"?

  Read the article

• Is it possible to use a laptop charger in other laptop with different specifications?

  - by poz2k4444

  Let's say I have my laptop charger that uses 19.5V and 3.9A and I want to use it in other laptop that has no charger but it needs just 19V and 3.16A, I've studied a little of electtronics and I know that the amperage doesn't affect because the computer will use just the necessary, but I'm not really sure about the voltage. I read this post and I know the polarity is the same and the connector fits, but it doesn't say anything about voltage, I also know if the voltage of the charger were lower than the specification it'll not be a problem, but what about this little almost insignificant difference??

  Read the article

• Damaged XenServer Storage LVM partition table

  - by Fiolek

  I have a homeserver running under XenServer control with 3x1TB discs inside, one for XenServer and two mirrored(using Intel's fakeRAID and dmraid) for VMs and a user data(but now I think RAID didn't work). I tried to pass PCI card to VM using PCI-passthroug and I read somewhere that I need to recompile kernel with pciback module but something went wrong(I made mistake in /boot/extlinux.conf and server couldn't run) and I had to use LiveCD of GPartEd(I already had it on USB key) to correct this. But when I re-run the server all VDIs were gone. I have completly no idea what could go wrong. I tried to repair RAID using dmraid -R in the hope that everything will return to noramal but now I think this done more bad than good(and corrupted rest of LVM table...). Is there any possibility to recover this SR or only data from one(~100GB) of VDI? I also wants to apologise for my English, I'm not from English-speaking country and I'm only 16 years old, so I hadn't "time" to learn it(school isn't good place to do this) in sufficient way.

  Read the article

• How to point a Wordpress registered domain to github pages?

  - by Dave Castillo

  I'm trying to use a CNAME file in my git hub project to point to my wordpress registered domain name. E.g. example.com to point to myusername.github.com. I read Github-Setting up a custom domain and it tells me to point the domain to their servers: For a TLD like example.com, you should use an A record pointing to 204.232.175.78: But in the wordpress domain manager I only get the option to specify a nameserver like this: NS1.WORDPRESS.COM NS2.WORDPRESS.COM Inputting 204.232.175.78 in the wordpress manager give me an "invalid TLD." What am I doing wrong and how can I troubleshoot this issue?

  Read the article

• "Fast link detected" warning in GP management console

  - by ???????? ??????

  There is a message that is shown in every report i make in Group Policy Results section of Group Policy Management Console, saying that "A fast link is detected". I followed the link in the waring, but after I read the page several times, I concluded, that I can ignore the warning. However, I noticed that the group policies are not applied when security filtering is used untl "gpupdate /sync" is executed... Is this related to the fast sync? In general, can somebody explain me the consequences of fast links briefly?

  Read the article

• How to install Mac OS X from Windows without a CD

  - by John Smith

  I have two partitions, one for windows the other for Mac OS X. Recently, my Mac OS X crashed and my partition rendered unbootable. When I insert Mac OS X's installation CD everything seems normal from startup, to choosing whether to boot from Windows or CD, until the CD boots. The screen flickers and it becomes extremely dark can barely see anything but I can see that it is booted correctly. I tried increasing brightness but that did not work. After hours of trying to read what is on the screen and guessing where to click the installation did not go through... It took more than a couple of hours so I restarted. Now the partition is accessible through Windows but is not bootable. TL;DR Is it possible to install Mac OS X on a visible partition without the CD through Windows XP?... Thanks

  Read the article

• SQL log shipping for reporting

  - by Patrick J Collins

  I would like to create a read-only copy of my SQL Server 2008 database on a secondary server for reporting and analysis. I've been testing log shipping, configured to run every 5 minutes or so. Alas, there appears to be a stumbling block, for exclusive access is required on the target database during the restore, which in turn requires killing all active connections. This is far from ideal, especially if a user is in the middle of running a report. Any better suggestions? Edit : I'm doing this on the Express edition.

  Read the article

• How can I get data off of a Corsair SSD?

  - by user1870398

  My Corsair SSD won't work and I have some critical data on it that I didn't back up (I needed to create a copy of my mechanical storage device, just forgot). The drive isn't detected by the OS or BIOS. I also tried it on another system, but all that happened was the OS failed to load (my guess was that it knew the drive was there, just couldn't read it). I tried powering it on without the data cable for a bit of time to see if it'd work again, but it didn't. Any ideas of how I can get the data off of this drive without having to send it in?

  Read the article

• What am I doing wrong with this cat 6 patch panel wiring?

  - by Max Hodges

  top number is transmitter bottom number is remote terminator 12345678 36145278 is this because I could be mixing T568A and T568B wiring? how do I know if my patch cord is A or B? Do I just look at the plug and match it up with the diagram on the back of the panel somehow? EDIT I read that 36145278 indicates a cross over cable, but I'm not trying to make a cross over. Where did I go wrong? I'm guessing the cable plug is T568A but I wired it to the panel using T568B. So I need to redo it as T568A. But in the future how do I know if I cable is A or B? Cheers!

  Read the article

• I split partition in Windows 7 home edition but the Windows doesn't reboot

  - by Samnan

  I Have Geniune Windows 7 home edition and my Laptop is Pavilion HP DV6 . I had only 1 partition of 500+ GB i Wanted to make another partition. I read somewhere in forum that I have to make my C: logical and then I'd be able to split C: I did the same thing using Partition Wizard. I made C: of 125 GB and shift rest of the space in New drive. I made a bootable disk, performed all the task using partition Wizard After that I have not been able to boot my windows. Even after running system restore several times.

  Read the article

• Exchange 2010 - No Push notification when when deleting emails from Outlook

  - by ThinkTank

  Hi I'm setting up a Exchange 2010 server for our test environment. I'm running Windows 2008R2 enterprise on this machine. Iv'e also installed all updates available for windows and exchange 2010 including rollup 1 and 2 for exchange that include bugfixes regarding push notifications. My problem is when deleting mail or marking mail as read don't trigger a push notification. The happens when I use webgui, mobile phone and Outlook 2007. When deleting a email in Outlook 2007 the changes get sent to the server since the changes are visible in webgui but not on mobile phone. I get push notifications when I get new emails since new emails appear instantly on the mobile phone. Is this normal behaviour on Exchange 2010? For me it seems a bit funny. If i force sync on mobile phone the changes appear. Iv'e tested this on both iphone and HTC HD2(Running Windows Mobile 6.5) with same results.

  Read the article

• "My Documents" as the first class citizen in "Documents" in Windows 7

  - by Dennis

  In windows 7, you can have a "Document" as a menu on the "Start Menu". However, it lead to sub-items "My Documents" and "Public Documents". As well as only me is using my notebook, "Public Documents" is useless and waste me for a click to the "My Documents". So, my question is -- how do I hack the registry(without hacking DLLs) to make the contents in "My Documents" as the first class citizen in the start menu? PS. after read this, I've removed the "Public Documents" from the library. But still, it takes me one more click

  Read the article

• Debian Unstable + Postfix 2.6.5 + dkim-filter 2.8.2 issue

  - by kura

  I have Postfix installed on Debian Unstable, as the title states, the system is completely up-to-date, I have tried to get DKIM signatures working on outgoing mail using dkim-filter 2.8.2. I couldn't use the default Debian way of doing things with sockets, instead I used the Ubuntu way: SOCKET="inet:12345@localhost"` I have the following in my postfix/main.cf milter_default_action = accept milter_protocol = 6 smtpd_milters = inet:localhost:12345 non_smtpd_milters = inet:localhost:12345 All is fine except I get the following message I start DKIM in mail.log: dkim-filter[22029]: can't configure DKIM library; continuing And when it tries to sign mails I get the following error: postfix/cleanup[22042]: warning: milter inet:localhost:12345: can't read SMFIC_EOH reply packet header: Success And then dkim-filter daemon stops. I've looked through Google but found no actual way to fix this that works for me. I have this working fine on an Ubuntu server but would love to get it working on Debian too.

  Read the article

• Best MTA setup for home or laptop computers - not server

  - by thomasrutter

  Hello, What is a good MTA (e.g. Postfix or something else) setup for a home computer behind a NAT, or a laptop that connects to various different wifi networks? I've read a lot of Postfix tutorials on how to set it up this way or that, but they are usually geared towards computers that are servers ie they have a static IP have a domain name are always connected to the same network My requirements are, I guess: Ability to forward mail for "root" to another server of my choosing. No listening for incoming SMTP connections - outgoing only Ability to route outgoing mail via an external SMTP server with authentication (and perhaps encryption) If not Postfix, I need an MTA which can queue up mails in case it temporarily has no internet connection.

  Read the article

< Previous Page | 602 603 604 605 606 607 608 609 610 611 612 613  | Next Page >