Search Results

Search found 49026 results on 1962 pages for 'open source alternative'.

Page 608/1962 | < Previous Page | 604 605 606 607 608 609 610 611 612 613 614 615  | Next Page >

• switchless Infiniband between two servers on RHEL 6.3

  - by exfizik

  I have 2 servers running RHEL 6.3 which have 2 port Infiniband cards >lspci | grep -i infini 07:00.0 InfiniBand: QLogic Corp. IBA7322 QDR InfiniBand HCA (rev 02) I'm interested in connecting them directly to each other bypassing an Infiniband switch (which I don't have). Quick googling showed that at least in some configurations it's possible. I installed all RedHat Infiniband packages with yum groupinstall "Infiniband Support". However, ibv_devinfo shows that both ports in each card are down, which indicates that cables are not connected. But the cable is connected, although the LEDs are off on the cards (not a good sign). Another source of confusion for me is that according to this, RedHat doesn't come with OFED packages and I'm slightly hesitant to install them from source due to the lack of RedHat support for them... So where am I going with this? The questions I have are: is it possible to have a switchless/direct Infiniband connection between two servers the way I described above? If it's possible, do I have to use the OFED packages or can I configure everything with just the packages coming with RHEL. Why are the LEDs off on my servers even though the cable is connected? Any additional input/advice/pointers would be appreciated. P.S. I followed this guide for installation instructions. The Infiniband cards are clearly recognized by my OS and the rdma service is running. Update: I have opensm installed. When I run it it says: OpenSM 3.3.13 Command Line Arguments: Log File: /var/log/opensm.log ------------------------------------------------- OpenSM 3.3.13 Entering DISCOVERING state Using default GUID 0x1175000076e4c8 SM port is down and stays at that point.

  Read the article

• Problems sending and receiving data between php and perl?

  - by Chip Gà Con

  I have a problem in sending and receiving data between php and perl socket: -Problem: +php can not send all byte data to perl socket +Perl socket can not receiving all data from php . Here code php: function save(){ unset($_SESSION['info']); unset($_SESSION['data']); global $config,$ip; $start=$_POST['config']; $fp = fsockopen($_SESSION['ip'], $config['port'], $errno, $errstr, 30); if(!$fp) { $_SESSION['info']="Not connect "; transfer("Not connect".$ip, "index.php?com=server&act=info"); } else { $_SESSION['info']="Save config - ".$ip; fwrite($fp,$start); transfer("Sending data to ".$ip, "index.php?com=server&act=info"); } } Here code perl socket: #!/usr/bin/perl use strict; use warnings; use Carp; use POSIX qw( setsid ); use IO::Socket; $| = 1; my $socket = new IO::Socket::INET ( LocalHost => '192.168.150.3', LocalPort => '5000', Proto => 'tcp', Listen => 5, Reuse => 1 ); die "Coudn't open socket" unless $socket; print "\nTCPServer Waiting for client on port 5000"; my $client_socket = ""; while ($client_socket = $socket->accept()) { my $recieved_data =" "; my $send_data=" "; my $peer_address = $client_socket->peerhost(); my $peer_port = $client_socket->peerport(); print "\n I got a connection from ( $peer_address , $peer_port ) "; print "\n SEND( TYPE q or Q to Quit):"; $client_socket->recv($recieved_data,20000); #while (defined($recieved_data = <$client_socket>)) { if ( $recieved_data eq 'q' or $recieved_data eq 'Q' ) { close $client_socket; last; } elsif ($recieved_data eq 'start' or $recieved_data eq 'START' ) { $send_data = `/etc/init.d/squid start`; } elsif ($recieved_data eq 'restart' or $recieved_data eq 'RESTART' ) { $send_data = `/etc/init.d/squid restart`; } elsif ($recieved_data eq 'stop' or $recieved_data eq 'STOP' ) { $send_data = `/etc/init.d/squid stop`; } elsif ($recieved_data eq 'hostname' or $recieved_data eq 'HOSTNAME' ) { $send_data= `hostname`; } elsif ($recieved_data eq 'view-config' or $recieved_data eq 'VIEW-CONFIG' ) { $send_data = `cat /etc/squid/squid.conf` ; } else { # print $recieved_data; open OUTPUT_FILE, '> /root/data' or die("can not open file"); print OUTPUT_FILE $recieved_data; close OUTPUT_FILE } #} if ($send_data eq 'q' or $send_data eq 'Q') { $client_socket->send ($send_data); close $client_socket; last; } else { $client_socket->send($send_data); } }

  Read the article

• missing network usage through iptables

  - by Purres

  I inserted a rule to iptables to track the input usage to a certain ip address. The vps server's IP is 192.168.1.5 and the guest os's IP is 192.168.1.115. I ran 'yum update' inside the guest OS to get some network traffic. Then I ran iptables -vnL from the hypervisor. However it only showed network usage to the host, but not to the guest. Chain INPUT (policy ACCEPT 0 packets, 0 bytes) pkts bytes target source destination 0 0 0.0.0.0/0 0.0.0.0/0 destination IP range 192.168.1.115-192.168.1.115 1853 114K 0.0.0.0/0 0.0.0.0/0 destination IP range 192.168.1.5-192.168.1.5 I ran tcpdump and the log showed that there're data packets to the guest os. 16:17:43.932514 IP mirrordenver.fdcservers.net.http > 192.168.1.115.34471: Flags [.], seq 17694667:17696115, ack 1345, win 113, options [nop,nop,TS val 1060308643 ecr 1958781], length 1448 16:17:43.932559 IP 192.168.1.115.34471 > mirrordenver.fdcservers.net.http: Flags [.], ack 17696115, win 15287, options [nop,nop,TS val 1958869 ecr 1060308643], length 0 Why the guest OS network usage couldn't be tracked? iptables -L will return the INPUT chain as following: Chain INPUT (policy ACCEPT) target prot opt source destination all -- anywhere anywhere destination IP range 192.168.1.115-192.168.1.115 all -- anywhere anywhere destination IP range 192.168.1.5-192.168.1.5 all -- anywhere anywhere

  Read the article

• VMWare player grabbing mouse focus

  - by Bryan Rowe

  I am using the newest VMWare player on a Windows 7 machine. When I have the player open on one of my two monitors I get some weird behavior. For instance, if the player is open on monitor 2, and I minimize firefox on monitor 1, my mouse will instantly switch to the monitor 2 and be centered within the VMWare player window. This happens when I minimize any window after having been working in my VM. I hope there is a setting or tweak that I am not aware of that can remedy this. EDIT: Through more testing I have found that this only occurs when the VMWare player is full screen on either of my two monitors. Also, I found people having the exact same issue at: http://communities.vmware.com/message/1244913

  Read the article

• Windows 7: Can't see ISO file in C:\

  - by cbp

  I used DVD shrink to create an ISO file and saved it into C:\ The ISO file is visible with some programs but not with others. The file is not hidden as far as I am aware. But it cannot be seen by Windows Explorer, DVD Decrypter or a bunch of other programs. If I search for the file using Windows 7's Start Menu search tool, I can see the file and I can right click and select Properties. The Properties window appears OK, but if I try to change tabs on the property window, I receive an error message as though the file is not there. DVD Shrink can still open the file OK. I can also find the file using Agent Ransack (a file searching tool), but then I cannot open it. What gives?

  Read the article

• Need clear steps on how to convert a Windows 2000 Server to a XenServer VM

  - by Jay

  The source system is not local. The target host running XenServer is not local. The source system is running Windows 2000 Server SP4 and has 1 disk split into 6 partitions, all NTFS: C: 6 GB (boot) D: 15 GB E: 6 GB F: 6 GB G: 5 GB H: 26 GB Most of the partitions are mostly mostly full ( 60%). What is the most straightforward way to do a P2V migration of the server? I can do minor database & data syncs after the P2V is successful & running as a VM within XenServer, it's just getting to that point which is not clear. The option of installing a Windows 2000 Server from scratch is not available, I need to convert the existing physical server as-is into a VM to be hosted within a XenServer environment. I've looked at XenConvert but it maxes out on converting only 4 partitions in one shot, and I'm not certain how to account for the 2 extra partitions. I'm not familiar with XenServer but it's my only option right now to go P2V.

  Read the article

• Windows 2008 Group Policy Setting? - Migration Headache

  - by DevNULL

  I have a small domain of users that I just migrated from a linux domain running open-ldap. Our new servers are running Windows 2008 Standard. I've installed Active Directory and everything is working perfectly... except that the initial user privileges is pretty restrictive and I need to loosen it up a bit. For example once they login to their workstations, they can create new files and folders but can not modify existing files or start. I basically want to open it all up except for software installations. Can someone please help with with this migration headache?

  Read the article

• How to remap a NERDTree shortcut in VIM

  - by btelles

  Hi There, I use the Dvorak keyboard layout with VIM, and the 't' key is the 'up' motion when editing a regular file. The problem is that NERDTree remaps 't' to open files in a new tab. How can I undo that mapping and use 't' for the up motion in NERDTree? Here are the relevant lines from my vimrc file and from the NERDTree plugin. My .vimrc: no t k NERDTree plugin file: exec "nnoremap <silent> <buffer> ". g:NERDTreeMapOpenInTab ." :call <SID>openInNewTab(0)<cr>" call s:initVariable("g:NERDTreeMapOpenInTab", "t") let @h=@h."\" ". g:NERDTreeMapOpenInTab.": open in new tab\n"

  Read the article

• One domain, dedicated SSL IP on whm

  - by Vanja D.

  It's long, but please read carefully. I am trying to install an SSL certificate on my dedicated server with WHM/cPanel. I have a dedicated IP to use with the SSL certificate. My main domain is example.com (NOT www.example.com), and I have an account and website already running on it. I bought the certificate for the main domain (example.com without www.). I installed the certificate (successfully). I used the example.com domain, the dedicated IP and the same cPanel user which owns example.com (non-ssl) I double checked ConfigServer for port 443 being open. RESULT: https://example.com won't open, ssl check tool returns a "SSL is not configured on this port (443)" error. I have three questions: where did I go wrong, wht did I miss? is it possible to have one domain on two ips (one for http, one for https)? is it possible to have an ssl host with the same user as the regular one?

  Read the article

• Lightweight Linux distro that includes developer tools? (or, the most BSD-like Linux)

  - by RevAaron

  I cut my teeth on Minix and Slackware 1.1, but I've been in the OS X Wilderness for the last few years. I'm trying to standardize on a Linux distribution for personal and work-related use on less powerful laptops and under virtualization. So far, NetBSD and OpenBSD are the best fit for my purposes- but after plenty of frustration I've come to the conclusion that I need to stick with Linux to get the hardware and software support that comes with it. What I like about NetBSD/OpenBSD that I'd like to keep: X, but no default KDE, GNOME or XFCE! A sensible /etc and dot file setup- startx calls xinit, xinit looks for ~/.xinitrc; nothing more complicated than that is needed. Command line tools and file-based configuration: I shouldn't need a GUI to connect to a WAP. Decent selection of binary packages; building from source is OK, but nothing source-only like Gentoo. pkg_add (BSD) and apt-get both have treated me well in the past. Modest RAM and HDD requirements: boot + X + awesome+ two xterms takes up 80 MB on OpenBSD and 240 MB on Debian 5 and Crunchbang In my experience, most "lightweight" and Live CDs focus on a nice desktop environment crammed into a CD or USB stick; once you add build-essentials you end up with something just about as bloated as Ubuntu or Debian full install. Crunchbang is a great example. Thanks in advance for all suggestions!

  Read the article

• Why doesn't the People Pane in Outlook 2010 show appointments for individual contacts?

  - by Curtis

  Outlook 2010 will not show appointments in the people pane. Under the activities tab if I go to All Items then eventually the appointments will show, but this takes a seriously long time. If I then click off the tab to look at another field then return to All Items, all the appointments are gone again. I need to be able to: Open a contact and see when that contact has appointments Open an appointment and see which contacts are attached to that appointment It works well from the appointment card to the contact, but has me completely frustrated going from the contact card to find the appontments. I have tried many things but cannot solve this problem. My set up is as follows: Exchange Server Windows 7 Ultimate Indexing enabled Cached exchange mode enabled Help! This is the whole reason I installed Outlook 2010.

  Read the article

• Event Log: atapi - the device did not respond within the timeout period - Freeze

  - by rjlopes

  Hi, I have a Windows Server 2003 that stops working randomly (displays image on monitor but is completely frozen), all I could found on the event log as causes were an error from atapi and a warning from msas2k3. The event log entries are: Event Type: Error Event Source: atapi Event Category: None Event ID: 9 Date: 22-07-2009 Time: 16:13:33 User: N/A Computer: SERVER Description: The device, \Device\Ide\IdePort0, did not respond within the timeout period. For more information, see Help and Support Center at http : // go.microsoft.com / fwlink / events.asp. Data: 0000: 0f 00 10 00 01 00 64 00 ......d. 0008: 00 00 00 00 09 00 04 c0 .......À 0010: 01 01 00 50 00 00 00 00 ...P.... 0018: f8 06 20 00 00 00 00 00 ø. ..... 0020: 00 00 00 00 00 00 00 00 ........ 0028: 00 00 00 00 01 00 00 00 ........ 0030: 00 00 00 00 07 00 00 00 ........ Event Type: Warning Event Source: msas2k3 Event Category: None Event ID: 129 Date: 22-07-2009 Time: 16:14:23 User: N/A Computer: SERVER Description: Reset to device, \Device\RaidPort0, was issued. For more information, see Help and Support Center at http : // go.microsoft.com / fwlink / events.asp. Data: 0000: 0f 00 10 00 01 00 68 00 ......h. 0008: 00 00 00 00 81 00 04 80 ......? 0010: 04 00 00 00 00 00 00 00 ........ 0018: 00 00 00 00 00 00 00 00 ........ 0020: 00 00 00 00 00 00 00 00 ........ 0028: 00 00 00 00 00 00 00 00 ........ 0030: 01 00 00 00 81 00 04 80 ......? Any hints?

  Read the article

• IE9 Kiosk Mode scheduled task opens behind taskbar

  - by greg27

  I've set up a scheduled task in Windows 7 Pro to open up Internet Explorer 9 (x86 version) in kiosk mode. The scheduled task executes when a certain user logs in, and this user is logged in automatically when Windows starts. This is the command I'm using to start IE: "C:\Program Files (x86)\Internet Explorer\iexplore.exe" -k http://example.com So far so good - the computer boots up, the user gets logged in, and IE opens up in kiosk mode. The problem is that IE seems to open behind the taskbar - so the taskbar (start menu, pinned programs, etc.) appears at the bottom of the window, and the bottom of the IE window is visible through the taskbar (since the taskbar is translucent). Is there anything I can do, preferably without installing any third party programs (although I will go for that option if none other is available), to ensure that the IE9 kiosk window always opens in front of the taskbar?

  Read the article

• 1000Base-X layer 2/MAC address details

  - by user69971

  A layer 2 Ethernet frame is sent with a source and destination MAC address. Given a 100Base-TX (copper) trunk between two Cisco switches, I can do a "show interface fa 0/0" on S1 to see the MAC address assigned to the trunking interface, then go to Switch2 and do a "show mac address-table" and find the MAC address of the S1 fa 0/0 interface as a dynamically learned MAC in the table. Given a similar setup with a 1000Base-X (fiber GBIC) trunk, the MAC address shown in "show interface gi 0/0" on S1 does not show up in the MAC address-table of S2. Everything I can find online indicates that 1000Base-X uses largely the same layer 2 format as copper connections. There's some slight alterations - minimum frame size is slightly larger - but the fundamentals of the frame structure appear to be the same, including transmission with a source and destination L2 address. Why doesn't the address of gi 0/0 show up in the MAC address table of the connection switch? The only thing which seems to make sense would be that the GBIC has its own MAC address, almost as if its acting as a mini 2-port switch or hub, with the switch-assigned MAC address showing up on the interface connection and a different MAC address assigned to the fiber side. If this is the case, is there any way to see the GBIC MAC address on the switch? (I've tried to look up the details in IEEE 802.3z but it doesn't seem to be available without an IEEE membership or purchasing the standard. I find the base 802.3 PDFs for download, but not 802.3z.)

  Read the article

• Why does terminal prompt text becomes black when connecting to Ubuntu with Nomachine NX client?

  - by David B

  I'm using Nomachine NX client for Windows to remotely connect to my Ubuntu. Every now and then I experience a strange phenomena: the text in the prompt of all open terminal windows becomes black, so it can't be viewed over the black background. Typed commands are also black, but the results are in normal colors. So I can run stuff, but can't see what I'm typing... After I close all open terminal windows and start a new terminal window, everything goes back to normal. This is rerally annoying and happens quite often. Any idea why?

  Read the article

• How do I change the URL handler for Apple Mail?

  - by Alex Reynolds

  When I highlight and right-click on text in an email message in Apple Mail 4.4 (1082), I can select "Search in Google". Despite having either Google Chrome or Mozilla Firefox set as my default web browser within Apple Safari 5.0.3 (6533.19.4) preferences, Apple Mail will open Safari, then open a new window in Safari with the search results. How do I change the default URL handler in Apple Mail, so that searches are opened in my default browser? Or is this a known bug? Thanks for your advice!

  Read the article

• Real-time local backup with versioning on Windows 7/8

  - by Borda

  I'm looking for a reliable backup solution on Windows, something with a feature set similar to Yadis. I've been using CrashPlan for 2 months, but their software lost more than 1TB of my data, that's why I'm looking for alternatives. Requirements: Real-time folder-to-folder backup: I don't need online features, I want to use this to duplicate my files between my local disks. Versioning support: Should be able to choose how many versions to keep of the files. Plain backup: I'd like to be able to open the backup without special software. No proprietary file format. External disk support: Shouldn't have any problem using external disks, at least on the source side. Backup every file, even locked/system files. (Yadis fails this one) Should start automatically, and have a comfortable GUI. Should use actively maintained and/or popular software. I don't want to use discontinued products. Optional requirements: Low RAM usage I'm not really comfortable with something that eats 1GB of my RAM. Compression support Preferably ZIP, but I'm not picky about this. Any ordinary everyday format is acceptable. Freeware or Open Source Preferred, but not necessary. I can do a one-time payment within reasonable bounds. (preferably under $100) I only need Windows support, but if it works on Linux, that's a plus. I've already searched and tried lots of software, most of them failed at the plain backup, the versioning or the locked file backup requirements.

  Read the article

• File transfer from MP3 player to computer

  - by JP

  I own an old 20GB Creative Zen jukebox (all external screws are gone on it LOL) and I would like to transfer files back to my PC to get them on my new iPod. Problem is, no matter what software I use (WinAMP, Creative Media Source or Windows Media Player), it just stops transferring files on my HD with an error message that says there is no more space on the destination folder. Problem is, there is still 320GB free. I tried lot of things like installing newer driver, latest Zen plug-in for Media Source, latest WinAMP version. Sometimes, it just works and then again, it stops working and I get this non-sense error. Restarting my PC sometime solves the issue by giving me enough time to transfer 10 or 15 more files and then I get the error again and again. Yesterday though I managed to transfer up to 3GB of MP3s on my computer before getting the error. Seems like I'm having a driver issue or a weird behavior from the player and/or the software I'm using. 3 different software can't reproduce the exact same issue by themselves so it must be something related to the driver. I can't find any post of any sort concerning such issue on old forums. Any idea?

  Read the article

• Windows Live Family Safety Service keeps closing Start Menu

  - by Jim McKeeth

  Got my kids a new Toshiba Laptop for Christmas. I was setting it all up for them so it would be ready to go. Tonight I installed Windows Live Family Safety Parental Controls. In the process of testing I discovered that on all the accounts the Start Menu closes automatically within 3 seconds (or less) of opening. It seems that it happens every 3 seconds, so sometimes it is immediate, and if I open it again then it will stay open for a full 3 seconds. This of course is rather annoying, and I need to wrap it up so it is ready to go under the tree. I disabled the Windows Live Family Safety Service, and that fixed it. Enable it again and the behavior returns. Is this a feature of the service? Can I disable that feature and keep the other features?

  Read the article

• How can I explain to dspam that the user "brandon" is the same as "brandon@mydomain"

  - by Brandon Craig Rhodes

  I am using dspam for spam filtering by running the "dspamd" daemon under Ubuntu 9.10 and then setting up a Postfix rule that says: smtpd_recipient_restrictions = ... check_client_access pcre:/etc/postfix/dspam_everything ... where that PCRE map looks like this: /./ FILTER lmtp:[127.0.0.1]:11124 This works well, and means that all users on my system get all of their email, whether "dspam" thinks it is innocent or not, and have the option of filtering on its decisions or ignoring them. The problem comes when I want to train dspam using my email archives. After reading about the "dspam" command, I tried this on the files in my Inbox and spam boxes (which date from when I was using another filtering solution): for file in Mail/Inbox/*; do cat $file | dspam --class=innocent --source=corpus; done for file in Mail/spam/*; do cat $file | dspam --class=spam --source=corpus; done The symptom I noticed after doing all of this was that dspam was horrible at classifying spam — it couldn't find any! The problem, when I tracked it down, was that I was training the user "brandon" with the above commands, but the incoming email was instead compared against the username "brandon@mydomain", so it was running against a completely empty training database! So, what can I do to make the above commands actually train my fully-qualified email address rather than my bare username? I would like to avoid having to run "dspam" as root with a "--user" option. I would have expected that the "dspam" configuration files would have had an "append_domain" attribute or something with which to decorate local usernames with an appropriate email domain, but I can't find any such thing. When I used to use the Berkeley DB backend to "dspam", I solved this problem by creating a symlink from one of the databases to the other. :-) But that solution eventually died because the BDB backend is not thread-safe, so now I have moved to the PostgreSQL back-end and need a way to solve the problem there. And, no, the table where it keeps usernames has a UNIQUE constraint that prevents me from listing both usernames as mapping to the same ID. :-)

  Read the article

• Time not propagating to machines on Windows domain

  - by rbeier

  We have a two-domain Active Directory forest: ourcompany.com at the root, and prod.ourcompany.com for production servers. Time is propagating properly through the root domain, but servers in the child domain are unable to sync via NTP. So the time on these servers is starting to drift, since they're relying only on the hardware clock. WHen I type "net time" on one of the production servers, I get the following error: Could not locate a time-server. More help is available by typing NET HELPMSG 3912. When I type "w32tm /resync", i get the following: Sending resync command to local computer The computer did not resync because no time data was available. "w32tm /query /source" shows the following: Free-running System Clock We have three domain controllers in the prod.ourcompany.com subdomain (overkill, but the result of a migration - we haven't gotten rid of one of the old ones yet.) To complicate matters, the domain controllers are all virtualized, running on two different physical hosts. But the time on the domain controllers themselves is accurate - the servers that aren't DCs are the ones having problems. Two of the DCs are running Server 2003, including the PDC emulator. The third DC is running Server 2008. (I could move the PDC emulator role to the 2008 machine if that would help.) The non-DC servers are all running Server 2008. All other Active Directory functionality works fine in the production domain - we're only seeing problems with NTP. I can manually sync each machine to the time source (the PDC emulator) by doing the following: net time \\dc1.prod.ourcompany.com /set /y But this is just a one-off, and it doesn't cause automated time syncing to start working. I guess I could create a scheduled task which runs the above command periodically, but I'm hoping there's a better way. Does anyone have any ideas as to why this isn't working, and what we can do to fix it? Thanks for your help, Richard

  Read the article

• RAID1 Hard drives with Intel Controller

  - by Dave_H

  I have an older server with 2 35GB hard drives arranged as a RAID-1 drive. I have 3 open bays, I'd like to add 2 more hard drives to the open bays and have all 4 drives configured as a RAID-1 drive that Windows sees as 1 larger drive. Is this possible? If not, the new drives are 2x as big as the old drives, is it possible to replace 1 of the old drives and rebuild then replace the second drive and rebuild and somehow expand the array to use all of the available space? The server is using an Intel hardware raid controller, the software interface is Intel Storage Console v2.12.

  Read the article

• How to launch a remote process through ssh and end the connection?

  - by Lukasz Lew

  This is still blocking: ssh host nohup cmd This still leaves the connection open: ssh host nohup cmd &

  Read the article

• Problem installing Cardbus/PCMCIA drivers (USB 2.0 2-port)

  - by Carl

  I obtained the drivers from the manufacturer for my HT-Link NEC USB 2.0 2-port Cardbus card. When I plugged in the card before I got the drivers, 3 new entries showed up in the Device Manager - two "NEC PCI to USB Open Host Controller" and one "Standard Enhanced PCI to USB Host controller." With the card plugged in, I uninstalled those two drivers. I then removed the card. I copied the new drivers to c:\windows\system32\drivers and the .inf file to c:\windows\inf. I also copied the drivers & inf to a new directory called c:\windows\drivers\ousb2. I reinserted the card. Windows automatically installed the same drivers as before. I selected 'update driver' on the "NEC PCI to USB..." entry and didn't see any other options. I then selected 'have disk' and pointed to c:\windows\drivers\ousb2 and got a message "The specified location does not contain information about your hardware." I then selected 'update driver' on the "Standard Enhanced PCI to USB...," and manually selected "USB 2.0 Enhanced Host Controller" (OWC 4/15/2003 2.1.3.1). Windows then automatically found a USB root hub, and I manually selected "USB 2.0 Root Hub Device" (OWC 4/15/2003 2.1.3.1). Now there are two sections in the Device Manager titled "Universal Serial Bus controllers." I plugged in my external USB hard disk adapter, and "USB Mass Storage Device" was added to the first set. Here's how it looks (w/drivers from the properties): [Universal Serial Bus controllers] Intel(R) 82801DB/DBM USB 2.0 Enhanced Host Controller - 24CD (6/1/2002 5.1.2600.0) Intel(R) 82801DB/DBM USB Universal Host Controller - 24C2 (7/1/2001 5.1.2600.5512) Intel(R) 82801DB/DBM USB Universal Host Controller - 24C4 (7/1/2001 5.1.2600.5512) Intel(R) 82801DB/DBM USB Universal Host Controller - 24C7 (7/1/2001 5.1.2600.5512) NEC PCI to USB Open Host Controller (7/1/2001 5.1.2600.5512) NEC PCI to USB Open Host Controller (7/1/2001 5.1.2600.5512) USB Mass Storage Device USB Root Hub (7/1/2001 5.1.2600.5512) (5 more USB Root Hubs - same driver) [Universal Serial Bus controllers] USB 2.0 Enhanced Host Controller (OWC 4/15/2003 2.1.3.1) USB 2.0 Root Hub Device (OWC 4/15/2003 2.1.3.1) When I unplug the card the two "NEC PCI to USB..." entries in the first set disappear, and the whole second set disappears. (I unplugged the hard disk adapter first...) The hard disk adapter still doesn't work in that Cardbus card with the new drivers. I don't think the above looks right - a second set of USB controllers listed in the Device Manager, and the NEC entries still in the first set, and the the USB mass storage device still in the first set. Any help appreciated. (Windows XP PRO SP3 w/all current updates.)

  Read the article

• Strange corruption saving from Textpad 5 within Windows 7-64 VirtualBox VM to shared folder with Mac host

  - by joelarson

  I have a fairly new Window-7 64bit install running in Virtual Box on a MacBook Pro. I'm using TextPad 5 within that environment to edit source files that live on a shared folder that is on the Mac Host. When I save some of these source files, the saved file ends up with some amount of the end of the file repeated one or more times. For example, a file that has this at the end: ... return ttp; }; would, once saved, open up with: ... return ttp; }; }; It is definitely a problem with how the file gets written as opposed to how it's read, because I can see this now matter what app I use to open the file with (NotePad & Word in Windows 7, TextWrangler back in the Mac). I've tried saving as ANSI and UTF-8, and with or without the 'Write Unicode and UTF-8 BOM' checked in TextPad preferences. It doesn't happen with all files though I can't see any pattern about which files do or don't have the problem. It doesn't happen with files written to the Windows 7 c:\ drive. And so far it doesn't happen from other applications saving files, only TextPad. Any ideas? My versions: Textpad 5.4.2 Windows 7 Professional 64-bit, fully up to date VirtualBox 4.0.8 r71778 OSX 10.6.7

  Read the article

< Previous Page | 604 605 606 607 608 609 610 611 612 613 614 615  | Next Page >