Search Results

Search found 4638 results on 186 pages for 'john kube'.

Page 62/186 | < Previous Page | 58 59 60 61 62 63 64 65 66 67 68 69  | Next Page >

• Determine which version of linux/unix/darwin I have

  - by John

  I have root ssh/terminal access to a linux server. How do I determine which version of centos I have? Some people suggested I run the command cat /etc/redhat-release but I got an error saying file not found. In fact, i'm not entirely sure i'm even using CentOS. That's what some suggested it might be. Here's a list of commands I tried that gave me no file or directory error: cat /etc/*release* cat /etc/*version* cat /proc/*version* cat /proc/*release* Here's a list of linux commands that do not exist: lsb_release: command not found wget: command not found yum: command not found

  Read the article

• K8NDRE motherboard in server fails to complete BIOS load with error 0078

  - by John

  K8NDRE motherboard with 4 sata drives, was running fine. Drives had raid-0 and raid-1 partitions, using mdadm. The onboard raid is disabled. Upon reformatting the drives, setting a new partition structure and new raid partitions, the bios fails to finish loading, with 0078 in the bottom right corner. Tried using completely new set of drives, and bios worked fine. Able to boot from a usb, format the drives, partition them, start raid, and then installed os. Reboot and received the same error from the bios, 0078. Works fine if I unplug the sata drives. Any thoughts? Physical inspection reveals no damage cables, connectors, or capacitors. Server was running happily for over a year, and this is the first problem it has had. Per Michael Hampton's answer: The drives, unjumpered and supporting sata III worked fine originally, and worked fine for formatting and having new partitions and raid installed on them. I did try jumpering one, with no change. If I put a brand new unformatted drive in, the motherboard recognizes it and I can proceed with formatting and installing. When I reboot, I get the 0078. I have 4 sata cables-the board supports 4 drives, so I tried each and no change. I am close to calling the motherboard done.

  Read the article

• Installing php(suexec) for Apache

  - by John

  I've got Apache installed and running but how do i install and run PHP as fastcgi so it runs as its own user? here is my apache config: ./configure --prefix=/usr/local/apache2 --enable-rewrite=shared --enable-so --enable-suexec --disable-asis --disable-autoindex --enable-cache --enable-deflate --enable-disk-cache --enable-expires --enable-file-cache --enable-mem-cache --enable-ssl --enable-vhost-alias --with-mpm=prefork --with-port=8080 here is my php config: ./configure prefix=/usr/local/php --without-pear --enable-safe-mode --enable-magic-quotes --with-apxs2=/usr/local/apache2/bin/apxs --disable-cli --disable-cgi --enable-force-cgi-redirect --enable-fastcgi --with-mysql --with-gd --with-jpeg-dir=/usr/lib --with-png-dir=/usr/lib --with-freetype-dir=/usr/lib --enable-calendar --with-curl --enable-mbstring --with-mcrypt

  Read the article

• How to control fan speed using SpeedFan?

  - by John Young

  The CPU fan in my laptop is running too fast. I wish to control the speed manually to my preference, at times. Here is a CPU-Z screenshot of my laptop configuration: http://i.stack.imgur.com/1oST1.png And here is how SpeedFan window looks at my end: http://i.imgur.com/BIi0RdJ.jpg I have no idea how to use SpeedFan to control my laptop's CPU fan speed. How to configure it so that I can increase and decrease speed of the fan at my will? Edit: Sorry, the first image wasn't as intended, so I've corrected it now. Also, if someone can edit the post and embed the images in the post, that would be great. I need at least 10 reputation to successfully accomplish that.

  Read the article

• cheapstuff.com malware

  - by John Peet

  I left my computer off for a couple of weeks and since my Windows 7 updates have been installed I have managed to gather a malware virus. It tries to redirect me on almost all websites I go to. I have read many ways to solving this issue manually, but it seems difficult and I dont want to delete any important files by mistake. All the instructions I have read seem complicated and generic all leading to a company that say they can help remove it. Is it their scam?? Can anybody help by giving me any free software or a descriptive run through for beginners of how to manually remove it? cheers guys

  Read the article

• Sticky Load Balancing with AWS

  - by John Wheal

  I have just setup a load balancer with AWS for a few instances as search engine crawlers were bringing down the site (it has millions of pages). Parts of the site allow you to login so I selected: Enable Application Generated Cookie Stickiness and everything works fine. I now wonder how this will effect my SEO and the crawlers. As I selected sticky load balancing does this mean that a crawler will be stuck on one server and therefore defeat the point in the load balancer? Any recommendations will be appreciated.

  Read the article

• hybrid cable for QSFP to CX4 convertion

  - by John-ZFS

  here is a hybrid cable for QSFP to CX4. Will this fit SFP+ ports? Deeply confused by standards and struck in a situation with wrong hardware selection!Personally have not seen the ports/hardware and hence the obviously stupid question! thanks for stopping by and bearing with me. http://www.cablesondemand.com/pcategory/72/category/QSFP+-+CX4/URvars/Catalog/Library/InfoManage/QSFP_TO_CX4_COPPER_CABLES.htm

  Read the article

• VirtualPC/XPMode... trying to let a VM access pages served using IIS on the host machine

  - by John

  My host PC is running IIS7.5 under Windows7. I have a VM running XP to let me use IE6, but I've no idea what network settings on the VM/host are needed so the VM can access pages on the host. I thought if the host was 192.168.1.1, then from the VM I'd simply do http://192.168.1.1/... if I do this on the host it works but the VM can't see it. I'm assuming there are some shortcuts here rather than manually having to set up loads of permissions, e.g a shortcut way of letting the VM access the host maybe?

  Read the article

• 3D in Windows 7 on Thinkpad R51

  - by John W.

  I installed Windows 7 on my laptop, and now the 3D doesn't work. According to dxdiag DirectX 11 is installed, but when I open up World of Warcraft, this error comes up. World of Warcraft World of Warcraft was unable to start up 3D acceleration. Please make sure DirectX 9.0c is installed and your video drivers are up-to-date. There are no alerts from Windows to update any drivers. Why doesn't the 3D work?

  Read the article

• Amazon EC2 firewall rules & VPN connections

  - by John

  I'm moving from Rackspace to Amazon EC2. One thing I like about our Rackspace setup is that it is extremely secure. The MySQL box can only be accessed via internal IPs, and we have a Cisco VPN firewall that allows us to dial in remotely and access port 3306 as though we were on the internal network. I'd like to figure out how to replicate this setup with EC2. How can I make the MySQL box so that port 3306 can only be accessed on the internal network? What about the VPN piece of things? I know Amazon has the VPC service, but it seems like that's for the purpose of connecting to an existing network. I don't have an existing network. I want to essentially create one inside Amazon and connect to that. What are my options? Any good tutorials on how to get started? Thanks in advance for your help

  Read the article

• Copying partial cell to another cell in OpenOffice Calc

  - by Justin

  Cell A1 says 0001 John Smith Cell A2 says 0002 Bill Snyder I want to basically split this, so one column just shows the numbers (0001, 0002, etc.) and then another column just shows the name. The first part is easy. Using the function "=LEFT(A1;4)" I can get 0001. How can I grab the name? Using "RIGHT(A1;99)", for example, will grab the entire string "0001 John Smith". Since each name is different in length, I'm not sure what to do. Can I somehow tell it to grab the whole string EXCEPT the first 4 characters? Or somehow tell it to grab the last 2 WORDS instead of a number of characters like it's asking?

  Read the article

• How do you backup 40+ Centos5.5 servers?

  - by John Little

  We are embarrassed to ask this question. Apologies for our lack of UNIX expertise. We have inherited 40+ centos 5.5 servers, and don't know how to back them up. We need low level clone type images so that we could restore the servers from scratch if we had to replace the HDs etc. We have used the "dd" command, but we assume this only works if you want to back up one local disk to another, not 40 servers to one server with an external USB HD attached. All 40 servers have a pair of mirrored disks (dont know if its HW or SW raid). Most only have 100MB used. SErvers are running apache, zend, tomcat, mysql etc. Ideally we dont want to have to shut them down to backup (but could). We assume that standard unix commands like tar, cpio, rsync, scp etc. are of no use as they only copy files, not partitions, all attributes, groups etc. i.e. do not produce a result which can simply be re-imaged to a new HD to get the serer back from dead. We have a large SAN, a spare windows box and spare unix boxes, but these are only visible to one layer in the network. We have an unused Dell DL2000 monster tape unit, but no sw or documentation for it. WE have a copy of symantec backup exec, but we have no budget for unix client licenses. (The company has negative amounts of money). We need to be able to initiate the backup remotely, as we can only access the servers in person in an emergency (i.e. to restore) Googling returns some applications to do this, e.g. clonezilla - looks difficult to install and invasive. Mondo, only seems to support backup if you are local to the machine. Amanda might be an option, but looks like days/weeks of work to learn and setup? Is there anything built into Centos, or do we have to go the route of installing, learning and configuring a set of backup softwares? Any ideas? This must be a pretty standard problem which goggling doesnt give an obvious answer.

  Read the article

• xen hotplug can't add vif to eth0: operation not supported

  - by John Tate

  I am new to xen and I am trying to get a domU running but I am having problems with it. I think my network card might not support bridging which is bizarre. This is the error I get when trying to create the domU [root@hyrba ~]# xm create sardis.secusrvr.com.cfg Using config file "/etc/xen/sardis.secusrvr.com.cfg". Error: Device 0 (vif) could not be connected. Hotplug scripts not working. All the xen kernel modules are loaded... xen_pciback 52948 0 xen_gntalloc 6807 0 xen_acpi_processor 5390 1 xen_netback 27155 0 [permanent] xen_blkback 21827 0 [permanent] xen_gntdev 10849 1 xen_evtchn 5215 1 xenfs 3326 1 xen_privcmd 4854 16 xenfs I get this error in /var/log/xen/xen-hotplug.log RTNETLINK answers: Operation not supported can't add vif2.0 to bridge eth0: Operation not supported can't add vif2.0-emu to bridge eth0: Operation not supported

  Read the article

• what is the best GUI editor in ubuntu-9.10 linux system?

  - by john

  what is the preferred GUI editor for PHP on linux systems, can we use Notepad++

  Read the article

• How do you passthrough native SATA drives to a guest on ESXi?

  - by John

  I have ESXi 4.0 running on an Intel DX58S0 Mothboardboard with an Intel Core i7 930 processor. VT-d is also enabled. I have three drives in the system, drive 0 is used for ESXi. Drive 1 and 2 contain data from an older machine and show up under the "Storage Adapters" section in configuration. I would like to allow a guest machine to access the data on these drives (as nativly as possible). I have enabled passthrough of the motherboard's built in SATA controller (Intel/Marvell 88SE6121 ). This controller shows up in my guest OS, but the guest shows no drives aside from the normal virtual drive. I have tried a Linux guest and Windows7. I have also configured the host machine to try IDE/RAID/ACHI modes for the SATA controller. Any ideas how I can configure one of my guests to get at the raw data on these drives?

  Read the article

• Speeding Up Search On Ubuntu File Server Accessed Through Windows

  - by John Birdy

  I run an Ubuntu box as a media server, which I use to either share files (copy and paste off of the network drive), or stream to my computer (which runs Win7), or to my xbox. I have a lot of files on there, especially music. Currently when I'm searching for a file, I just use Windows' search, which can be quite slow. I was wondering if there were better ways to search from my Windows box? I'd prefer not to SSH in to the box and use find or something like that. Is there any way to speed up Windows' search? Or an easy alternative? Thanks!

  Read the article

• volume group disappeared after xfs_check run

  - by John P

  EDIT** I have a volume group consisting of 5 RAID1 devices grouped together into a lvm and formatted with xfs. The 5th RAID device lost its RAID config (cat /proc/mdstat does not show anything). The two drives are still present (sdj and sdk), but they have no partitions. The LVM appeared to be happily using sdj up until recently. (doing a pvscan showed the first 4 RAID1 devices + /dev/sdj) I removed the LVM from the fstab, rebooted, then ran xfs_check on the LV. It ran for about half an hour, then stopped with an error. I tried rebooting again, and this time when it came up, the logical volume was no longer there. It is now looking for /dev/md5, which is gone (though it had been using /dev/sdj earlier). /dev/sdj was having read errors, but after replacing the SATA cable, those went away, so the drive appears to be fine for now. Can I modify the /etc/lvm/backup/dedvol, change the device to /dev/sdj and do a vgcfgrestore? I could try doing a pvcreate --uuid KZron2-pPTr-ZYeQ-PKXX-4Woq-6aNc-AG4rRJ /dev/sdj to make it recognize it, but I'm afraid that would erase the data on the drive UPDATE: just changing the pv to point to /dev/sdj did not work vgcfgrestore --file /etc/lvm/backup/dedvol dedvol Couldn't find device with uuid 'KZron2-pPTr-ZYeQ-PKXX-4Woq-6aNc-AG4rRJ'. Cannot restore Volume Group dedvol with 1 PVs marked as missing. Restore failed. pvscan /dev/sdj: read failed after 0 of 4096 at 0: Input/output error Couldn't find device with uuid 'KZron2-pPTr-ZYeQ-PKXX-4Woq-6aNc-AG4rRJ'. Couldn't find device with uuid 'KZron2-pPTr-ZYeQ-PKXX-4Woq-6aNc-AG4rRJ'. Couldn't find device with uuid 'KZron2-pPTr-ZYeQ-PKXX-4Woq-6aNc-AG4rRJ'. Couldn't find device with uuid 'KZron2-pPTr-ZYeQ-PKXX-4Woq-6aNc-AG4rRJ'. PV /dev/sdd2 VG VolGroup00 lvm2 [74.41 GB / 0 free] PV /dev/md2 VG dedvol lvm2 [931.51 GB / 0 free] PV /dev/md3 VG dedvol lvm2 [931.51 GB / 0 free] PV /dev/md0 VG dedvol lvm2 [931.51 GB / 0 free] PV /dev/md4 VG dedvol lvm2 [931.51 GB / 0 free] PV unknown device VG dedvol lvm2 [1.82 TB / 63.05 GB free] Total: 6 [5.53 TB] / in use: 6 [5.53 TB] / in no VG: 0 [0 ] vgscan Reading all physical volumes. This may take a while... /dev/sdj: read failed after 0 of 4096 at 0: Input/output error /dev/sdj: read failed after 0 of 4096 at 2000398843904: Input/output error Found volume group "VolGroup00" using metadata type lvm2 Found volume group "dedvol" using metadata type lvm2 vgdisplay dedvol --- Volume group --- VG Name dedvol System ID Format lvm2 Metadata Areas 5 Metadata Sequence No 10 VG Access read/write VG Status resizable MAX LV 0 Cur LV 1 Open LV 0 Max PV 0 Cur PV 5 Act PV 5 VG Size 5.46 TB PE Size 4.00 MB Total PE 1430796 Alloc PE / Size 1414656 / 5.40 TB Free PE / Size 16140 / 63.05 GB VG UUID o1U6Ll-5WH8-Pv7Z-Rtc4-1qYp-oiWA-cPD246 dedvol { id = "o1U6Ll-5WH8-Pv7Z-Rtc4-1qYp-oiWA-cPD246" seqno = 10 status = ["RESIZEABLE", "READ", "WRITE"] flags = [] extent_size = 8192 # 4 Megabytes max_lv = 0 max_pv = 0 physical_volumes { pv0 { id = "Msiee7-Zovu-VSJ3-Y2hR-uBVd-6PaT-Ho9v95" device = "/dev/md2" # Hint only status = ["ALLOCATABLE"] flags = [] dev_size = 1953519872 # 931.511 Gigabytes pe_start = 384 pe_count = 238466 # 931.508 Gigabytes } pv1 { id = "ZittCN-0x6L-cOsW-v1v4-atVN-fEWF-e3lqUe" device = "/dev/md3" # Hint only status = ["ALLOCATABLE"] flags = [] dev_size = 1953519872 # 931.511 Gigabytes pe_start = 384 pe_count = 238466 # 931.508 Gigabytes } pv2 { id = "NRNo0w-kgGr-dUxA-mWnl-bU5v-Wld0-XeKVLD" device = "/dev/md0" # Hint only status = ["ALLOCATABLE"] flags = [] dev_size = 1953519872 # 931.511 Gigabytes pe_start = 384 pe_count = 238466 # 931.508 Gigabytes } pv3 { id = "2EfLFr-JcRe-MusW-mfAs-WCct-u4iV-W0pmG3" device = "/dev/md4" # Hint only status = ["ALLOCATABLE"] flags = [] dev_size = 1953519872 # 931.511 Gigabytes pe_start = 384 pe_count = 238466 # 931.508 Gigabytes } pv4 { id = "KZron2-pPTr-ZYeQ-PKXX-4Woq-6aNc-AG4rRJ" device = "/dev/md5" # Hint only status = ["ALLOCATABLE"] flags = [] dev_size = 3907028992 # 1.81935 Terabytes pe_start = 384 pe_count = 476932 # 1.81935 Terabytes } }

  Read the article

• Why is my SSH session timing out in less than a minute?

  - by John Smith

  Within a minute of connecting to my remote Linux server through SSH, my session times out and I cannot contact the server until a few seconds have passed. Meanwhile, I'm connected to other servers without interruption. This is only happening when I establish connection from an hotel wireless AP. When I connect from my phone's Internet, the problem does not occur. Does anyone know what might be causing these unusual timeouts?

  Read the article

• Setup local EC2 style cloud?

  - by John Kramlich

  I was recently given 3 dual opteron 2400 servers with 4GB of RAM and 120GB hard drives. I am interested in setting up something similar to Amazon's EC2 for my own personal web development use. Basically, I would like to spin up instances from an ISO or other disk images and have them available to test and develop software. Are there open source solutions I can use to accomplish this? I am assuming one of the machines will need to act as a controller of some sort for the other two. I use Sun's VirtualBox on my local development machine to virtualize various versions of Microsoft Windows. However, I'm not sure if that's the best tool for what I am trying to achieve. I apologize in advance if this question is to vague to get meaningful responses. I am new to cloud computing and fairly new at server administration.

  Read the article

• Postfix sasl: Relay access Denied (state 14)

  - by Primoz

  I have postfix installed with dovecot. There are no problems when I'm trying to send e-mails from my server, however all e-mails that are coming in are rejected. My main.cf file: queue_directory = /var/spool/postfix command_directory = /usr/sbin daemon_directory = /usr/libexec/postfix mail_owner = postfix inet_interfaces = all mydestination = localhost, $mydomain, /etc/postfix/domains/domains virtual_maps = hash:/etc/postfix/domains/addresses unknown_local_recipient_reject_code = 550 mynetworks = 127.0.0.0/8 alias_maps = hash:/etc/aliases alias_database = hash:/etc/aliases home_mailbox = Maildir/ debug_peer_level = 2 debugger_command = PATH=/bin:/usr/bin:/usr/local/bin:/usr/X11R6/bin xxgdb $daemon_directory/$process_name $process_id & sleep 5 sendmail_path = /usr/sbin/sendmail.postfix newaliases_path = /usr/bin/newaliases.postfix mailq_path = /usr/bin/mailq.postfix setgid_group = postdrop html_directory = no manpage_directory = /usr/share/man sample_directory = /usr/share/doc/postfix-2.3.3/samples readme_directory = /usr/share/doc/postfix-2.3.3/README_FILES smtpd_sasl_type = dovecot smtpd_sasl_path = private/auth smtpd_sasl_auth_enable = yes smtpd_recipient_restrictions = check_policy_service inet:127.0.0.1:9999, permit_mynetworks, permit_sasl_authenticated, reject_non_fqdn_recipient, reject_unknown_recipient_domain, reject_unauth_destination, smtpd_sender_restriction = reject_non_fqdn_sender broken_sasl_auth_clients = yes UPDATE: Now, when e-mail comes to the server, the server tries to reroute the mail. Example, if the message was sent to [email protected], my server changes that to [email protected] and then the mail bounces because there's no such domain on my server.

  Read the article

• Network Services disabled (not starting) on Windows XP

  - by Rickesh John

  I am currently running Windows XP Service Pack 3 on my system. But today, when I failed to connect to the internet, via a LAN cable, I realized that almost all of the vital network services had stopped functioning. Any attempts to start it through services.msc gives me the following message: Could not start the DNS Client Service on Local Computer Error 1068: The dependency service group failed to start All my software or services that are related to networking have stopped functioning, for example, Windows Firewall is turned off permanently, so is my Avast Anti-Virus' service of Real Time Shields and Web Shield. When I insert the LAN wire into my laptop, it registers itself, but this is what I get when I do a ping localhost C:>ping localhost Unable to contact IP driver, error code 2 Moveover, with ipconfig I get this : Windows IP Configuration An internal error occurred: The request is not supported. Please contact Microsoft Product Support Services for further help. Additional Information: Unable to query host name On some further poking around, I saw that none of the "NETWORK SERVICE" process in task manager, except svchost.exe were running. Also, when I first opened the task manager, I saw some 20 processes running with username column empty for most of them. With some search in Google, I found out that these services were important, DHCP DNS Net logon Network connection Network location Awareness TCP/IP Net BIOS Helper none of them, except Network Connections are working, they do not start. The event viewer of my system shows a bunch of 7000 and 7001 event errors. I have tried re installing the network driver, booting in safe mode with networking and tried to enable those services mentioned above. I had disabled System Restore some time back, so I have no restore points for my system. I tried a lot of things from Google searches but none of them worked. Also, with such a long list of issue, I am a little confused as to what should I search on the internet. :( One more thing I would like to mention, previous morning, my anti-virus Avast detected a RootKit buried deep in my system folders. It was removed, but maybe this was a problem caused by the root kit. I did run a boot-time scan but no viruses were found. Please please please advice. Is formatting and re-installation of Windows my only option?

  Read the article

• Computer has power but won't boot

  - by John Isaacks

  When I power on my computer it will not boot. It will not even go into bios or anything. It is as if it is not powering on at all, however the decorative casing lights turn on and the PC is making noise (like from the fans). I am reluctant to think it is the power supply since some part are getting power. I do not know what it is though? For the couple days leading up to this, the computer would make a loud noise and the screen would stop displaying anything. I had to reboot to get it to work again. Now nothing happens when I boot, except the case lights come on and it sounds like some fans are coming on. Any ideas?

  Read the article

• Determine creator of mail item in Exchange 2003 public folder

  - by John Gardeniers

  We have several users using a shared account and when messages in that account's in box have been processed they are drag and dropped into a public folder. Is there a way to determine who dropped a mail item in an Exchange 2003 public folder, so that we can have some accountability? I suspect this can't be done natively in Exchange, so if there is a scripted solution to this I'd be very interested.

  Read the article

• outlining in colors

  - by John

  ? I like outlining all information, but I am looking for better way to outline: I would like my outlines to be colorful like programming, so that it is very easy to distinguish between different types of texts within an outline. How can I do this?

  Read the article

• cruisecontrol.net failing build with no errors

  - by John Hoge

  Hi, I've been using CCNet for some time now but just upgraded to .net 4. I've installed the new framework on my dev box along with vs2010 and on my CC.net server as well. I've just installed CruiseControl.net version 1.5.6804.1, and changed my MSBuild tasks to point to the new v4.0.30319 framework directory. I've got two projects on .net 4 now that just don't build. They build perfectly well in VS and run well on both Cassini and IIS. I just don't get any error messages from cc.net, just this: BUILD FAILED Project: GoodBay Date of build: 2010-05-11 10:21:59 Running time: 00:00:02 Integration Request: Build (ForceBuild) triggered from SVN Modifications since last build (0)

  Read the article

< Previous Page | 58 59 60 61 62 63 64 65 66 67 68 69  | Next Page >