Search Results

Search found 18728 results on 750 pages for 'setup deployment'.

Page 626/750 | < Previous Page | 622 623 624 625 626 627 628 629 630 631 632 633  | Next Page >

• Oracle Linux screen freezes during installation

  - by Fearless

  I was installing Oracle Linux 6.4 on a server, and the screen suddenly froze. Here were the previous steps: I put in the disk, clicked install, checked the disk (no errors), did pre-install setup (clock, root password, host+domain name, etc.), configured two 40GB hard drives in a RAID1 array (no swap, 3100mb encrypted raid partitions, ~100mb ext4 partition mounting to /boot, encrypted ext4 RAID device with mounting to /), selected packages, hit continue. The system did its short preinstall processes, then when to the main installation screen with the long status bar. The installer proceeded like always, but around package 250 out of ~1000, the screen suddenly went black with a text cursor in the upper left corner of the screen and the mouse cursor in its previous place. Neither cursor moved and the only thing that triggered a response was a ctrl-alt-delete that rebooted it. I have run this in VMs before without this issue. Memtest hasn't reported anything, and the media check went smoothly. The machine has supported Ubuntu server without issues before. Any ideas? I have tried booting after that, but the grub bootloader tries to find fd0 for some reason (I have no idea why it would search for the floppy disk). UPDATE My server successfully installed, but won't boot up. I think that, for some reason, it is still using the old bootloader from the previous installation. Any ideas on how to fix that?

  Read the article

• Having an issue trying to get Gigabit speed across my network (Ubuntu Server)

  - by user94217

  I've just started looking into the network speeds at my office, the entire network is setup to be "Gigabit". This includes Gb switches, Gb Network cards and Cat 5e cabling. I'm not expecting the full speed, I just want more than ~90 Mb/s. I've been running some tests with iperf the linux tools and checking the hardware with ethtool. I have 3 servers and when doing my checks/test I discovered that the two backup servers can access each other at around 450 Mb/s but when using either one of them to connect and test the main server, I only get the 90Mb/s even though ethtool shows the networking card running at 1000/Full. The only difference between all the server/networking cards is the "Port" which ethtool shows. On the two backup servers the "Port" is shown as MII yet on the other it's shown as "Twisted Pair". When using ethtool -s to manually set the "Port" to MII on the main server, it looses all connectivity and does not show "Speed" or "Duplex". Anyway, Am i doing something wrong? Is there a specific reason my main server cannot use Gb when there appears to be no difference except the "Port"?

  Read the article

• Hyper-V VM's cannot access Host resources, and vice-versa

  - by Agent

  I have several Hyper-V vm's running on this Win2008 R2 Server box, and up until a reboot of the host server, all the VM's were able to access shared folders on the host. Now, they can't even ping the host server. From what I've seen, I need to setup an Internal only network through Virtual Network Manager in Hyper-V. I set this up, then tried to enable the Microsoft Virtual Network Switch Protocol option in this Internal Only NIC, but I get popups saying: Your current selection will also disable the following features: Microsoft virtual network switch protocol Which is absolutely stupid, considering the protocol is what I'm ticking the checkbox to Enable! As of now, on the host, I have 2 NICs: Physical - This NIC on the host machine does have the MVNS protocol enabled Virtual Network Adapter - Created through Hyper-V Virtual Network Manager as an External type of network. Trying to enable MVNS on this NIC also produces the error above. I've tried enabling Client for Microsoft Networks on the physical NIC for IPv6, but everytime I do that, all the VMs lose Internet connectivity and I cannot RDP into them. Anything else I can try?

  Read the article

• Fixing Windows install by connecting its hard drive via USB to a different laptop

  - by Jason

  I tried to upgrade a laptop to SP3, which broke it. I later found out SP3 doesn't work on that 2002 laptop. I can't uninstall SP3, or fix SP2, because the hard drive is now not detected during setup (I've read that's the problem you get). I put the hard drive in a USB drive case and plugged it into my other laptop, and I can read (& write to) the disk okay. (The hard drive won't fit in my other laptop, so I'm using USB.) I need to get that disk back to SP2, or fix whatever files got screwed up causing the disk to not be recognized. I don't want to do a re-install as there are 80GB of files on it I need, and they won't fit on the HD of my other laptop, and also because I no longer have some of the install CDs for software on it. What do I need to do to fix that drive from my other laptop? (I don't want my working laptop (XP SP3) to get screwed with by putting an SP2 disk in the CD drive, or the non-o/s data on the other hard drive screwed with.)

  Read the article

• Fixing Windows install by connecting it's hard drive via USB to a different laptop

  - by Jason

  I tried to upgrade a laptop to SP3, which broke it. I later found out SP3 doesn't work on that 2002 laptop. I can't uninstall SP3, or fix SP2, because the hard drive is now not detected during setup (I've read that's the problem you get). I put the hard drive in a USB drive case and plugged it into my other laptop, and I can read (& write to) the disk okay. (The hard drive won't fit in my other laptop, so I'm using USB.) I need to get that disk back to SP2, or fix whatever files got screwed up causing the disk to not be recognized. I don't want to do a re-install as there are 80GB of files on it I need, and they won't fit on the HD of my other laptop, and also because I no longer have some of the install CDs for software on it. What do I need to do to fix that drive from my other laptop? (I don't want my working laptop (XP SP3) to get screwed with by putting an SP2 disk in the CD drive, or the non-o/s data on the other hard drive screwed with.)

  Read the article

• Allow members of a group to be unlocked by a specific account on AD

  - by JohnLBevan

  Background I'm creating a service to allow support staff to enable their firecall accounts out of hours (i.e. if there's an issue in the night and we can't get hold of someone with admin rights, another member of the support team can enable their personal firecall account on AD, which has previously been setup with admin rights). This service also logs a reason for the change, alerts key people, and a bunch of other bits to ensure that this change of access is audited / so we can ensure these temporary admin rights are used in the proper way. To do this I need the service account which my service runs under to have permissions to enable users on active directory. Ideally I'd like to lock this down so that the service account can only enable/disable users in a particular AD security group. Question How do you grant access to an account to enable/disable users who are members of a particular security group in AD? Backup Question If it's not possible to do this by security group, is there a suitable alternative? i.e. could it be done by OU, or would it be best to write a script to loop through all members of the security group and update the permissions on the objects (firecall accounts) themselves? Thanks in advance. Additional Tags (I don't yet have access to create new tags here, so listing below to help with keyword searches until it can be tagged & this bit editted/removed) DSACLS, DSACLS.EXE, FIRECALL, ACCOUNT, SECURITY-GROUP

  Read the article

• Should I be able to Windows Phone 8 emulator running with this AMD config

  - by pete

  I have just bought a new system as follows * AMD A4-5300 Trinity 3.4GHz * Gigabyte GA-F2A55M-DS2 Motherboard I checked and the A4-5300 supports Virtualisation. I have run the SLAT checking tool and it says that my machine supports SLAT. Been into the BIOS and ensures that SVN is enabled. I have also run the coreinfo tool that indicates that SVN is not valid fort the machine nor is NPT.. not sure why this conflicts with the true BIOS setting (I checked with GIGABYTE and seems that NPT and NX are not options that can be set in the BIOS) But.. when I run the emulator I it hangs - I can see some activity in Hyper-V manager, but it doesnt get very far and no meaningfull error messages. Been working the plethora of suggestions to get around this, but so far, nothing has worked. My question is should this setup allow the WP8 emulator to run. I am positive the CPU supports virtualisation, but are there issues with the motherboard here? I have spent a huge amount of time on this so far....am I wasting my time with the current configuration, or should it work? thanks

  Read the article

• GPG - why am I encrypting with subkey instead of primary key?

  - by khedron

  When encrypting a file to send to a collaborator, I see this message: gpg: using subkey XXXX instead of primary key YYYY Why would that be? I've noticed that when they send me an encrypted file, it also appears to be encrypted towards my subkey instead of my primary key. For me, this doesn't appear to be a problem; gpg (1.4.x, macosx) just handles it & moves on. But for them, with their automated tool setup, this seems to be an issue, and they've requested that I be sure to use their primary key. I've tried to do some reading, and I have the Michael Lucas's "GPG & PGP" book on order, but I'm not seeing why there's this distinction. I have read that the key used for signing and the key used for encryption would be different, but I assumed that was about public vs private keys at first. In case it was a trust/validation issue, I went through the process of comparing fingerprints and verifying, yes, I trust this key. While I was doing that, I noticed the primary & subkeys had different "usage" notes: primary: usage: SCA subkey: usage: E "E" seems likely to mean "Encryption". But, I haven't been able to find any documentation on this. Moreover, my collaborator has been using these tools & techniques for some years now, so why would this only be a problem for me?

  Read the article

• Why does my ftp(e)s server fails like half of the time

  - by user1092608

  I have this discussion at work regarding our ftp server running via vsftpd. Initially, we have opted to serve ftpes instead of sftp because this seemed the most flexible and straightforward solution for our server to have secure file transmission. Afterwards, our ftp server seems to be a source of issues for our end users. Half of the time, users complain about not working ftp connections. I must say, i tested our FTP trough different infrastructures (=in the field, at random times at random places) and indeed, sometimes behind some configurations (=no idea how they are configured, because the 'field' testing), i recieve errors. Some of the are: Error: Failed to retrieve directory listing (filezilla) Furthermore, behind my basic home configuration, everything seems to be running fine. I (think I) did all the basic configuration checks (passive mode?, firewall for all ports?, ...) and can't seem to find the source. Being a bunch of techies at our small office, yet knowing nothing about infrastructure, some start suggesting that ftps protocol could be the source of issues. ("No, i only knew sftp so far" "Ftps is not widespread"). I, however, strongly doubt this hypothesis, since reading around on the www, asking questions on serverfault, everyone seems to deny this. So, as I would like to avoid reconfiguring, since this involves messing around in our SSH service, our virtual user setup and ftp service, i would need some advice on 1) what could be potentially the general cause? 2) do you have some general tips? 3) would you mind having a look at my configuration file? ----- General Settings ----- write_enable=YES dirmessage_enable=YES nopriv_user=ftpsecure ftpd_banner="Welcome to XXXX FTP!" hide_ids=YES hide_file=.* max_per_ip=10 max_clients=10 local_enable=YES local_umask=022 chroot_local_user=YES secure_chroot_dir=/usr/share/empty userlist_enable=NO userlist_deny=YES userlist_file=/etc/vsftp_deny_users guest_enable=YES guest_username=ftpvirtual virtual_use_local_privs=YES user_sub_token=$USER local_root=/srv/ftp/ftpvirtual/$USER anonymous_enable=NO syslog_enable=NO xferlog_enable=YES xferlog_file=/var/log/vsftpd_xfer.log connect_from_port_20=YES pam_service_name=vsftpd listen=YES listen_port=21 pasv_enable=YES pasv_min_port=30000 pasv_max_port=30030 pasv_address=foo ssl_enable=YES rsa_cert_file=/etc/vsftpd.pem rsa_private_key_file=/etc/vsftpd.pem force_local_data_ssl=YES force_local_logins_ssl=YES ssl_tlsv1=YES ssl_sslv2=YES ssl_sslv3=YES ssl_ciphers=HIGH anon_mkdir_write_enable=NO anon_root=/srv/ftp anon_upload_enable=NO idle_session_timeout=900 log_ftp_protocol=NO dsa_cert_file=/etc/vsftpd.pem Thanks

  Read the article

• What needs to be considered when setting up for Linux Development? [closed]

  - by user123586

  I want to set up a box for Linux development. I have a working linux install with the usual toolchain and an IDE. I'm looking for advice on how to approach structuring accounts and folders for development. As the Perl folks say "There's always more than one way to do it." Left to my own devices, I'll come up with several unproductive ways of doing it before figuring out what an experienced Linux programmer would think obvious. I'm not looking for instructions to follow for a specific set of tools or a specific software package. Instead, I'm looking for insight into what decisions need to be made and how to make them, with understanding of the advantages and disadvantages of each individual choice. These are some of the questions that come up: Where to put sources Where to put built object files and libraries where to install what to set in environment variables what compiler flags matter and how do you manage them across several types of builds what configuration entries to make in an IDE how to manage libraries to support multiple environments how to handle different build versions such as debug vs release, or cross platform builds If you are an experienced Linux developer, the answers to these questions may seem trivial and obvious. I'd like to learn to make decisions about these questions that result in as little manual configuration as possible, given some existing sources, a particular IDE, or no IDE at all, a paticular set of development libraries etc. At this point you're probably thinking: Can you be more specific? Sure. But remember that I'm trying to learn how to think about this stuff, not just follow a recipie for a specific set of results. Example: Setup a project that uses CMake for some of its components, autogen.sh followed by configure for others and just configure for a few more: debug builds without an IDE debug builds in NetBeans debug builds in Eclipse debug build in Visual Studio all of the above with release builds for Linux, Mac and Windows. So... **What are your thoughts on an approach that works for all four? Do you have any advice on what to read?**

  Read the article

• Odd one: IE6 showing the "view source" command enabled when I was expecting it to be disabled.

  - by caerphilly

  Hi, OK, I admit this problem is odd. I'm just trying to understand why IE is behaving the way it is. I realise that logic may not apply here :) I have Internet Explorer 6 (Sp1) running on Windows 2000. The IE option "Do not store encrypted pages to disk" is checked (enabled). The temporary internet files folder is empty. TEMP and TMP environment variables are set to valid folders. I'm connected to a web server over SSL. The web server is serving a page over SSL with the HTTP cache-control header set to "no-cache, no-store". I was expecting the "view source" command to be greyed out in this circumstance (as it is on another machine). But it works. When I "view source", I get an entry in the Temporary Internet Files folder with an "internet address" property of "view-source:https://myserver/...." and the content of the page. I wasn't expecting that. I can't understand why one machine is different to another in this regard. Obviously there is some environment/setup difference, but I can't track it down. Anyone have any bright ideas?

  Read the article

• How do I serve Ruby on Rails applications on Windows Server 2008?

  - by Adam Lassek

  I have spent the last several hours attempting to get Ruby on Rails running on a Windows server with no luck. At first I tried configuring a test application through IIS7's FastCGI support, but the documentation for this is not very good. I've been following this blog entry, and this one, and this one, and this one but everything seems to be missing major steps, or are out of date. And every article keeps linking back to this Howto from rubyonrails.org that doesn't exist. The sense that I'm getting is that even if I manage to make this work, IIS' FastCGI isn't good enough to use in a production environment anyway. So it looks like my best bet is to setup a reverse proxy in IIS that points to Apache & Mongrel/Passenger using ARR and UrlRewrite. Is there anybody else out there stuck deploying a Rails application on a Windows stack? Am I on the right track? Can you give me a better idea of how to configure this? I believe Plesk already installed an instance of Apache/Tomcat running on this server using a different port, so adding another virtual host shouldn't be difficult; the hardest part seems to be setting up the reverse proxy through IIS.

  Read the article

• Ubuntu 12.04 can't boot after installing with software RAID 1

  - by Bill

  I've been trying to install Ubuntu with software RAID on my server and there is obviously something that I don't understand about the process. This is the guide that I followed: https://help.ubuntu.com/11.04/serverguide/advanced-installation.html I have two identical 1 TB disks in my server. I went through the initial install process and manually set up my partitions. On each disk I set up: (1) 100 MB partition for EFI boot (I didn't originally have this but added it based on a forum post I found after my original install failed to boot, I ended up with EFIboot since that was what the 'guided partitioning' decided to do) (1) 970 MB partition for / (1) 30 MB partition for swap I then created new RAID 1 disks combining the two partitions, one from each disk, such that each partition is mirrored. I then configured their usage as stated above. After saving the configuration I said yes to boot in a degraded state. The rest of the setup went normally, no errors of any kind. I saw GRUB being installed and again no errors. However, after rebooting the server I get the dreaded 'Insert boot media' and nothing happens. I loaded up the recovery disk and the mdadm configuration looks correct. md0 is my EFIBoot partition md1 is my \ partition using ext4 md2 is my swap partition Running file -s /dev/md0 doesn't indicate that GRUB is there and so I attempted to reinstall GRUB using the recovery disk. I selected the md0 disk and it appeared to install just fine. Running file -s /dev/md1 shows the error needs journal recovery, I'm not sure if that's related or not or how to fix that. Rebooting gives me the same problem, no boot media found. I've searched around the internet but can't figure out what to do next or more importantly how to troubleshoot what exactly is going wrong. Thanks!

  Read the article

• please explain these mongo statistics

  - by sivann

  My setup: I have 2 hosts, and 2 shards each. Host1 has 2 shards, and is the master of the replicas host2 has the secondaries of the 2 shards. . host1: shard1 (repset1),shard2 (repset2) host2: shard1 (repset1),shard2 (repset2) There's also a 3rd host that acts as arbitrer. I have 50 threads writing randomly to both shards (using a hash) via mongos with REPLICA_SAFE WriteConcern set on each insert. The questions: mongostat displays about 90% locked for both shards in host1 and about 1% locked on host2. Since I use REPLICA_SAFE which supposedly writes to both servers shouldn't the locks be the same? mongostat reports qr=30 for both shards of host1, and qw=0 always. Since I perform only writes how is this possible? Moreover on host2 all queues are reported 0. Faults are abut the same in all shards/hosts (arround 80). netIn/netOut on the secondaries (host2) are always about 200bytes/sec. Too low. mongos has 53 connections, host1's shards have 71 and 71 and host2's shards have 9 and 8. How is this? Please answer whatever you can. Thanks!

  Read the article

• Gentoo server time issue, can't manually set time, NTPD won't correct, too big of a time difference

  - by kevingreen

  So, my server is living in the future, unfortunately I can't get lottery numbers, or stock picks out of it. It thinks this is the time: Thu Nov 7 04:07:18 EST 2013 Not correct, I tried to set the time manually via date in a few ways # date -s "06 NOV 2013 14:48:00" # date 110614482013 -- same output, same problem Which outputs Wed Nov 6 14:48:00 EST 2013, but when I check the date again, it's still set to Nov 7th 0400 or whatever. I checked my system messages, and I see this pop up often: Nov 7 03:54:00 www ntpd[4482]: time correction of -47927 seconds exceeds sanity limit (1000); set clock manually to the correct UTC time. Which makes sense, we're way off the correct time. But I can't seem to manually fix it. So now what? Also, I'm wondering if my hardware clock is setup correct, hwclock doesn't return any values. Would that be causing issues? This is a virtualized server, I don't have direct access to the hypervisor, but I can talk to who does, assume I can explain myself well enough. Thanks

  Read the article

• Windows Server 2008 R2 grinds to a screeching halt during file copy operations

  - by skolima

  When my Windows Server 2008 R2 machine is performing any large disk operations (copying 10GB files from one drive to another, copying similar file over network, merging HyperV snapshots, compressing large files), performance of the whole machine slows down terribly, everything becomes unresponsive. This is noticeable in any situation when the disk access is large enough not to fit in the cache. Are there any settings available for tuning this behaviour? I can accept slower file transfer if this would give me more responsiveness. System details: Dell Optiflex 960, Core 2 Quad Q9650, 8GB RAM, 2 SATA drives - 320GB (ST3320418AS) and 1TB (ST31000528AS), NCQ active on both, Intel 82564LM-3 Gigabit Ethernet, ATI HD 3450 graphics, Intel ICH10 bridge. We have multiple machines like this, every one is exhibiting the same behaviour. I though this was overkill for a workstation, apparently I was mistaken. Update: I guess I shouldn't have mentioned the HyperV at all. The above configuration is a standard workstation setup at the company I work for, this is not a server of any kind. I have at most 3 virtual machines working, and usually I'm the only person accessing them. Never the less, the slowdown occurs even when no VMs are running. On a Linux machine I'd simply ionice the copy process and I could forget about it, is there any way to manage IO priorities on Windows?

  Read the article

• Why can't I connect to my home SSH (SFTP) server? What am I doing wrong?

  - by Rolo

  I am new to this topic of creating a SFTP server on one's computer. I would like to be able to access the folder on my Windows XP computer via SFTP from another computer or a phone. The following is what I have done so far: I have installed SSH Windows and everything is setup correctly because I can access it (the folder on my pc) via WinSCP. I however cannot access it from my phone. It doesn't connect. The phone can be on the same wireless network as the Windows XP computer, but I would prefer to be able to access this when not in the same network. Now, from what I have read and understood, the following is the information needed to connect: 1) Host Name: This would be my computer's ip address which I access by typing ipconfig in a cmd prompt (I access this easily on my computer because I simply put in localhost or 127.0.0.1) 2) Port Number: That would be port 22 (I have also added this to my router in the port forwarding section). 3) Username: This would be my Windows XP username. This however is my full name, including my middle initial followed by a period. I am wondering if this is maybe causing problems in accessing it from my phone, since the name has spaces and punctuation (the period). 4) Password: The password of my Windows XP computer Extra Info: When I say phone, I mean an Android phone and I am using an ftp / sftp app to access my pc via the phone's cellular network (I also tried the wireless, but that didn't work as well). I have tried more than one program. On one program it tells me Connection timed out and on another it tells me "timeout:socket is not established" Also, I know that I can use the site noip, but I prefer to connect this way first. Also, because I am new to this, I would like to look into what exactly noip is doing and if they would be seeing my files as they are transferred from phone to pc. Thanking you in advance for your help.

  Read the article

• Good support to multiple desktops AND multiple monitors in Linux (Ubuntu)?

  - by Somebody still uses you MS-DOS

  I'm starting to have A LOT of opened windows in my machine. Sometimes within a project, I have e-mail/task management/personal e-mail/twitter, and a lot of different opened applications/terminal in my Linux environment. Nowadays I have 4 worspaces: Corporate management (e-mail) and corporate messenger; Work (Documents, Requisites) Dev (Development, All gVim windows, terminal and Firefox for development) Personal (Personal stuff: personal e-mail, delicious, twitter and so on) Sometimes it would be interesting to have different workspaces to projects instead of this configuration I have nowadays that are classes of work (bad name, I know, but I think you got the idea). I'm starting to think about using two monitors: one with Corporate Management, Work and Personal. The second monitor is only the development state: each workspace here is about a project being worked on instead of groups of works like before. A workspace may be implementing different classes for example. My question is: I just want to change to a second monitor using the mouse. I want to still be able to change workspaces in the same monitor using keyboard shortcuts. The keyboard shortcuts wouldn't change monitors, just worskpaces on the same monitor. Does Linux (Ubuntu 10.04 Lucid Lynx) support this envisioned setup? If so, how?

  Read the article

• upstart scripts: run a task after networking goes up

  - by The Journeyman geek

  I'm working on moving my current server setup to newer hardware, and migrating from ubuntu karmic koala to lucid lynx. Currently i'm using gw6c (compiled from the gogo6 website, as opposed to the version from the repositories) to get ipv6 access for my systems. On the karmic koala system, i used simple init.d script to get the ipv6 client started #! /bin/sh /usr/local/gw6c/bin/gw6c -f /usr/local/gw6c/bin/gw6c.conf I figured since this runs at any runlevel, it should translate to respawn console none start on startup stop on shutdown script exec /usr/local/gw6c/bin/gw6c -f /usr/local/gw6c/bin/gw6c.conf emit free6_ipv6_started end script this works fine started from initctrl, but it apparently fails to start when it boots. - its status being stop/waiting. It works fine (and respawns) when started otherwise.Any ideas on where i'm going wrong, and what would be the appropriate 'start on' arguement? EDIT: the exact error is 'init: gw6c main process (xxx) ended with status 8' followed by the process respawning , with xxx being a PID i suspect. I'm also half suspecting this is cause gw6c starts before networking does, and i need my eth0 up before gw6c is

  Read the article

• Strange Domain name under the same IP Address

  - by Mike Chip

  There's something really weird happening in my server. But first things first: I wanted to have my website and chose the domain name "myowndomain.com", Now on my domain registrar I point "myowndomain.com" to the address of my recently setup VPS, let's say 50.50.50.50 So I installed everything I needed to run my website, and I started to notice strange queries coming from different IP Addresses. Like these [client 123.123.123.123] File does not exist: /var/www/html/api, referer: http://www.strangedomain.com/api/manyou/my.php [client 456.456.456.456] File does not exist: /var/www/html/api, referer: http://www.strangedomain.com/api/manyou/my.php or like this (Really a long line, I cut some things) GET /?s=vod-show-id-22-area-%E5%85%B6%E4%BB%96-language-%E9%9F%A9%E8%AF%AD.html HTTP/1.1" 301 295 "http://v.strangedomain.com/?s=vod-s ...[cut]... spider" That above is happening the most. The 'strangedomain.com' returns the same IP address of my VPS which my website is hosted on. The whois of such domain shows it's registered to a chinese. But the street name didn't look so right (like a huge single word), so I think all of that info might be fake, but still might be a chinese. I also noticed that all 'clients' trying to access the 'strangedomain.com' is coming from china. If I type in the browser 'strangedomain.com', I see my website. I'm worried, because my website is actually an e-commerce. I don't know if 'strangedomain.com' WAS a website on 50.50.50.50 in the not so far past, or if it's something else.

  Read the article

• How to get a list of Dovecot IMAP users

  - by Colt McCormack

  How do you get a list of users for a dovecot email server that connect via IMAP (as opposed to POP)? Our server is setup to authenticate via LDAP/PAM. Is there an easy way to get a list of the users who are accessing their mail via IMAP, rather than POP? I am about to migrate our server to Google Apps and want to migrate all of the mail for my IMAP users only (couple hundred out of several hundred total users). POP mail will be migrated separately from the client end obviously. I would much rather migrate only the IMAP users rather than the whole domain which would include migrating a bunch of POP mail left in the server that has already been read/sorted/deleted in the client's email program. Migrating all of that extra useless leftover POP mail could waste weeks of migration time. I suppose parsing some logs to see who has connected on an IMAP port (995 or 993) would give me a list would work if someone could help me do that. I know I have the raw dovecot logs, but am hoping for a cleaner solution.

  Read the article

• Amazon EC2 - Free memory

  - by Damo

  We have an amazon ec2 small instance running and over the past few days we noticed that the memory is going down and down. On the small instance, we are running apache and tomcat6 Tomcat is started with the following JVM parameters -Xms32m -Xmx128m -XX:PermSize=128m -XX:MaxPermSize=256m We use nagios to monitor stuff like updates to apply, free disk space and memory. Everything else is behaving as expected but our memory is going down all the time. Our app receives approx half a million hits a day When I shutdown apache and tomcat, and ran free -m, we had only 594mb of memory free out out of the 1.7gb of memory. Not much else is running on the small instance and when running the top command I cannot see where the memory is going. The app we run on tomcat is a grails webapp. Could there be a possibility that there is a memory leak within our application? I read online and folks say that a small amazon instance is perfect for running apach and tomcat. I found a few posts online that showed how to setup apache and tomcat to limit the memory usage and I have already performed those steps. The memory is not being used up as quick but the memory is still decreasing over time. We have other amazone ec2 small instances running grails apps and the memory is fairly standard on those nodes. But they would not be receiving as much traffic Just to add, when I run the top command on the problem server, I cannot see where all the memory is being used Any help with this is greatly appreciated The output of free -m when run on my server is as follows total used free shared buffers cached Mem: 1657 1380 277 0 158 773 -/+ buffers/cache: 447 1209 Swap: 895 0 895 In your opinion, does this look ok? At what stage would the OS give back memory, would it wait to the memory reaches 0% or is this OS dependent?

  Read the article

• Duplicate forwarded messages in Blackberry when using BIS

  - by Avery Payne

  Our Setup External email arrives at a Postfix server, is scanned, and then forwarded via settings in transport (using the RELAY:[{ip-address}] for a given address) to an Exchange 2007 server. Some users are on Exchange, but a few are still on the Postfix server (they will be moved in the near future). IMAPS is provided for external connections via Dovecot; in-house, IMAP is provided for the Gateway and native MAPI is used for Exchange/Outlook. Blackberries are connected via BIS, which uses Dovecot as a reverse-proxy IMAPS service to connect to Exchange (when the mailbox exists on Exchange, otherwise it connects to the mailbox on the gateway). The Issue We have a user that, when they forward an email on their Outlook client, they get a duplicate of the original message on their Blackberry. When I say duplicate, I mean that they have a copy of the forwarded version of the message (i.e. their version of the message that they obtained hitting the forward button), and a copy of the original message that shows up at the same time. The expected behavior is to just see the forwarded message, not the forwarded message and a 2nd copy of the original message. We've only seen this with Outlook users that also have a Blackberry. Other IMAP clients, such as OS X Mail or Thunderbird, do not exhibit this behavior when connecting to the Exchange server; forwarded messages work as expected. The Questions what is causing this to happen? why does it only affect Outlook/Blackberry setups, and not TBird/Blackberry or OSX-Mail/Blackberry? how do we get it to stop, before people go insane and never forward messages again?

  Read the article

• Apache Cache with multiple CacheRoots

  - by Tobias Greitzke

  I configured Apache with a CacheRoot directory for each of my domains / virtual hosts: <VirtualHost> ServerName domain1.tld ... CacheRoot /var/www/vhosts/domain1.tld/httpdocs/cache ... </VirtualHost> <VirtualHost> ServerName domain2.tld ... CacheRoot /var/www/vhosts/domain2.tld/httpdocs/cache ... </VirtualHost> I have this up and running for quite a while and so fare it's working pretty well except that I have to empty out the cache manually every so often because htcacheclean does't know of the different directories. Now I would like to setup htcacheclean to watch over the cache directories but as fare as I understand the manual, I can only set it to one cache directory. I would like to do something like this but that doesn't work: <VirtualHost> ServerName domain1.tld ... CacheRoot /var/www/vhosts/domain1.tld/httpdocs/cache htcacheclean -n -t -p/var/www/vhosts/domain1.tld/httpdocs/cache -l1024M ... </VirtualHost> Is it even right to have multiple cache directorys or should I work with just one cache directory for all of the domains?

  Read the article

• SQL Server: Network pauses after installing cheap SATA card: Is there a solution?

  - by samsmith

  At the risk of being assigned to the "bad DBA" club... I did something desperate, and may have to undo it. Problem: After installing a low cost eSATA board, my SQL Server is intermittently unresponsive (seemingly when there is a lot of IO to the eSATA drive). Questions: 1) Is there a solution to the intermittent unresponsiveness that allows me to keep the eSATA in place? 2) Whether or not (1==true): What is a decent, low cost way to add 1-3 TB storage to SQL for non-critical SQL DBs? Detail: Our SAN is full, and expanding it is costly and will take a month. I have a pressing need to add 1-3 TB for some development DBs (e.g. not mission critical; data loss is OK). As a bandaid, I threw a $20 eSATA PCI board in the Dell 1950 server, and attached an external 2TB eSATA drive. This seemed to work fine, but I notice that our production SQL DBs, and even remote desktop, now experience network "pauses" that they never did before (with both SQL client apps and remote desktop throwing "networking problem" errors). This SQL Server has lots of memory, and runs an instance of SQL 2005 (where all line of business apps reside) and an instance SQL 2008 (for development db's). SQL Server RAM has been appropriately configured, and this setup has run great for years. The server is: Dell 1950 Win2003 x64 14GB RAM PERC controller, 2 mirrored hd's internal Dell SAN over gbit ethernet, dual homed 2 PCIx slots (1 used by NIC for SAN, 1 now in use for eSATA board) Thank you for suggestions!

  Read the article

< Previous Page | 622 623 624 625 626 627 628 629 630 631 632 633  | Next Page >