Search Results

Search found 37031 results on 1482 pages for 'ms access'.

Page 628/1482 | < Previous Page | 624 625 626 627 628 629 630 631 632 633 634 635  | Next Page >

• Why I cannot copy install.wim from Windows 7 ISO to USB (in linux env)

  - by fastreload

  I need to make a USB bootable disk of Windows 7 ISO. My USB is formatted to NTFS, ISO is not corrupt. I can copy install.wim elsewhere but I cannot copy it to USB. I even tried rsync. rsync error sources/install.wim rsync: writefd_unbuffered failed to write 4 bytes to socket [sender]: Broken pipe (32) rsync: write failed on "/media/52E866F5450158A4/sources/install.wim": Input/output error (5) rsync error: error in file IO (code 11) at receiver.c(322) [receiver=3.0.8] Stat for windows.vim File: `X15-65732 (2)/sources/install.wim' Size: 2188587580 Blocks: 4274600 IO Block: 4096 regular file Device: 801h/2049d Inode: 671984 Links: 1 Access: (0664/-rw-rw-r--) Uid: ( 1000/ umur) Gid: ( 1000/ umur) Access: 2011-10-17 22:59:54.754619736 +0300 Modify: 2009-07-14 12:26:40.000000000 +0300 Change: 2011-10-17 22:55:47.327358410 +0300 fdisk -l Disk /dev/sdd: 8103 MB, 8103395328 bytes 196 heads, 32 sectors/track, 2523 cylinders, total 15826944 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xc3072e18 Device Boot Start End Blocks Id System /dev/sdd1 * 32 15826943 7913456 7 HPFS/NTFS/exFAT hdparm -I /dev/sdd: SG_IO: bad/missing sense data, sb[]: 70 00 05 00 00 00 00 0a 00 00 00 00 20 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ATA device, with non-removable media Model Number: UF?F?A????U]r???U u??tF?f?`~ Serial Number: ?@??~| Firmware Revision: ????V? Media Serial Num: $I?vnladip raititnot baelErrrol aoidgn Media Manufacturer: o eparitgns syetmiM Standards: Used: unknown (minor revision code 0x0c75) Supported: 12 8 6 Likely used: 12 Configuration: Logical max current cylinders 17218 0 heads 0 0 sectors/track 128 0 -- Logical/Physical Sector size: 512 bytes device size with M = 1024*1024: 0 MBytes device size with M = 1000*1000: 0 MBytes cache/buffer size = unknown Capabilities: IORDY(may be)(cannot be disabled) Queue depth: 11 Standby timer values: spec'd by Vendor R/W multiple sector transfer: Max = 0 Current = ? Recommended acoustic management value: 254, current value: 62 DMA: not supported PIO: unknown * reserved 69[0] * reserved 69[1] * reserved 69[3] * reserved 69[4] * reserved 69[7] Security: Master password revision code = 60253 not supported not enabled not locked not frozen not expired: security count not supported: enhanced erase 71112min for SECURITY ERASE UNIT. 172min for ENHANCED SECURITY ERASE UNIT. Integrity word not set (found 0xaa55, expected 0x80a5)

  Read the article

• Problems with "Read Only" on a Samba share from Windows machines

  - by fistameeny

  Hi, We have a Ubuntu 10.04 Server that has a bunch of Samba shares on it that Windows workstations connect to. Each Windows workstation has a valid username/password to access the shares, which have restricted access governed by Samba. The problem we are experiencing is that Samba doesn't seem to be able to mimic the Windows way of handling "Read Only" attributes. Say I have two users, UserA and UserB, both a group called Staff - UserA creates a file that is readable/writeable by the group (ie. chmod rwxrwx---). If UserA then sets the "Read Only" flag, this changes the permissions to r-xr-x--- (i.e. no write for anyone). As UserB is in the same group as UserA, they should be able to remove the "Read Only" permission - however, they can't as Samba won't allow it. Is there a way to force Samba to allow users within the same group to remove the "Read Only" from a file not created by them? Edit: The Samba smb.conf is as follows: The share is defined in the smb.conf as: [global] log file = /var/log/samba/log.%m passwd chat = *Enter\snew\s*\spassword:* %n\n *Retype\snew\s*\spassword:* %n\n *password\supdated\ssuccessfully* . obey pam restrictions = yes map to guest = bad user encrypt passwords = true passwd program = /usr/bin/passwd %u passdb backend = tdbsam dns proxy = no netbios name = ubsrv server string = ubsrv unix password sync = yes os level = 20 syslog = 0 usershare allow guests = yes panic action = /usr/share/samba/panic-action %d max log size = 1000 pam password change = yes workgroup = workgroup [Projects] valid users = @Staff writeable = yes user = @Staff create mode = 0777 path = /srv/samba/Projects directory mode = 0777 store dos attributes = Yes The folder itself looks like this: ls -l /srv/samba/ drwxrwxrwx 2 nobody Staff 4096 2010-11-04 10:09 Projects Thanks in advance, Matt

  Read the article

• Options for small windows network setup without dedicated server?

  - by Mitch

  I'm very weak on networking and hope someone can point me in the right direction: I have written some windows client/server software which incorporates a database which is located on a windows server. I have a test installation running at a customer's office where the server has a static IP address. In this case its easy for the clients to access the database because of the fixed IP address. Also, customers with network servers generally have specialist support staff to set up my software, so its not such a problem for me. However I also need to offer the software to customers who have small offices with less than 10 PCs and no dedicated network server. In this case I want the customer to be able to nominate one PC as the database "server" and install my software and have the clients access it. But in this situation I believe the "server" PC may not have a dedicated IP address. Q1: What is the best way to set this up simply and make it work? Can I reliably reference the "server" by using its name, or is there a way to assign dummy fixed IP addresses? Ideally this needs to be workable on small networks running a mixture of XP/Vista/Windows7 as my target market may well have mixed OSes etc. I guess this would be akin to home networking? Many thanks Mitch

  Read the article

• Some guest networking and VMware Tools functionality broken with Sprint SmartView on the host

  - by Mads

  Using VMware Workstation 6.5.3 on Vista 64-bit. I started having problems with VMware networking about 6 months ago after upgrades to Sprint SmartView. I did not have problems previously, but I don't know if that is because I was lucky. The main symptoms of the problem when SmartView is installed are: I can no longer drag files from the host to copy them to the guest. When they are dragged, the disallowed cursor (the circle with a slash) shows in the guest. If I try to enable shared folders in the guest while it is running, I will not be able to see the shared files and will be informed that networking is not working. I can still ping guests from the host and I can still access network services via NAT most of the time when connected via my USB broadband adapter. When I configure shared folders so they are "always enabled" (with a mapped drive), I can access files on the via the mapped folders. I can also copy the file on the host and then paste it in the guest, as was suggested in some other threads concerning drag-and-drop problems that I found. The VMware Tools icon is showing in all cases and I don't see any obvious errors in the host's event viewer. If I uninstall SmartView, the problems disappear. If SmartView (current version is 2.28.0082) is reinstalled I will experience the same problems. I have tried uninstalling/reinstalling VMware and SmartView in various ways but it appears tha these problems are consistent when SmartView is installed (not just when it is running or connected, but when it is present on the system). I'm wondering if this is a combination of software (WS 6.5.3, Vista64, and SmartView) that works for other people, which would indicate a problem that is peculiar to my configuration.

  Read the article

• CodePlex Daily Summary for Sunday, January 30, 2011

  CodePlex Daily Summary for Sunday, January 30, 2011Popular ReleasesWPF Application Framework (WAF): WPF Application Framework (WAF) 2.0.0.3: Version: 2.0.0.3 (Milestone 3): This release contains the source code of the WPF Application Framework (WAF) and the sample applications. Requirements .NET Framework 4.0 (The package contains a solution file for Visual Studio 2010) The unit test projects require Visual Studio 2010 Professional Remark The sample applications are using Microsoft’s IoC container MEF. However, the WPF Application Framework (WAF) doesn’t force you to use the same IoC container in your application. You can use ...Rawr: Rawr 4.0.17 Beta: Rawr is now web-based. The link to use Rawr4 is: http://elitistjerks.com/rawr.phpThis is the Cataclysm Beta Release. More details can be found at the following link http://rawr.codeplex.com/Thread/View.aspx?ThreadId=237262 and on the Version Notes page: http://rawr.codeplex.com/wikipage?title=VersionNotes As of the 4.0.16 release, you can now also begin using the new Downloadable WPF version of Rawr!This is a pre-alpha release of the WPF version, there are likely to be a lot of issues. If you...VivoSocial: VivoSocial 7.4.2: Version 7.4.2 of VivoSocial has been released. If you experienced any issues with the previous version, please update your modules to the 7.4.2 release and see if they persist. If you have any questions about this release, please post them in our Support forums. If you are experiencing a bug or would like to request a new feature, please submit it to our issue tracker. Web Controls * Updated Business Objects and added a new SQL Data Provider File. Groups * Fixed a security issue whe...PHP Manager for IIS: PHP Manager 1.1.1 for IIS 7: This is a minor release of PHP Manager for IIS 7. It contains all the functionality available in 56962 plus several bug fixes (see change list for more details). Also, this release includes Russian language support. SHA1 codes for the downloads are: PHPManagerForIIS-1.1.0-x86.msi - 6570B4A8AC8B5B776171C2BA0572C190F0900DE2 PHPManagerForIIS-1.1.0-x64.msi - 12EDE004EFEE57282EF11A8BAD1DC1ADFD66A654VFPX: VFP2C32 2.0.0.8 Release Candidate: This release includes several bugfixes, new functions and finally a CHM help file for the complete library.EnhSim: EnhSim 2.3.3 ALPHA: 2.3.3 ALPHAThis release supports WoW patch 4.06 at level 85 To use this release, you must have the Microsoft Visual C++ 2010 Redistributable Package installed. This can be downloaded from http://www.microsoft.com/downloads/en/details.aspx?FamilyID=A7B7A05E-6DE6-4D3A-A423-37BF0912DB84 To use the GUI you must have the .NET 4.0 Framework installed. This can be downloaded from http://www.microsoft.com/downloads/en/details.aspx?FamilyID=9cfb2d51-5ff4-4491-b0e5-b386f32c0992 - Added back in a p...DB>doc for Microsoft SQL Server: 1.0.0.0: Initial release Supported output HTML WikiPlex markup Raw XML Supported objects Tables Primary Keys Foreign Keys ViewsmojoPortal: 2.3.6.1: see release notes on mojoportal.com http://www.mojoportal.com/mojoportal-2361-released.aspx Note that we have separate deployment packages for .NET 3.5 and .NET 4.0 The deployment package downloads on this page are pre-compiled and ready for production deployment, they contain no C# source code. To download the source code see the Source Code Tab I recommend getting the latest source code using TortoiseHG, you can get the source code corresponding to this release here.Office Web.UI: Alpha preview: This is the first alpha release. Very exciting moment... This download is just the demo application : "Contoso backoffice Web App". No source included for the moment, just the app, for testing purposes and for feedbacks !! This package includes a set of official MS Office icons (143 png 16x16 and 132 png 32x32) to really make a great app ! Please rate and give feedback ThanksParallel Programming with Microsoft Visual C++: Drop 6 - Chapters 4 and 5: This is Drop 6. It includes: Drafts of the Preface, Introduction, Chapters 2-7, Appendix B & C and the glossary Sample code for chapters 2-7 and Appendix A & B. The new material we'd like feedback on is: Chapter 4 - Parallel Aggregation Chapter 5 - Futures The source code requires Visual Studio 2010 in order to run. There is a known bug in the A-Dash sample when the user attempts to cancel a parallel calculation. We are working to fix this.Catel - WPF and Silverlight MVVM library: 1.1: (+) Styles can now be changed dynamically, see Examples application for a how-to (+) ViewModelBase class now have a constructor that allows services injection (+) ViewModelBase services can now be configured by IoC (via Microsoft.Unity) (+) All ViewModelBase services now have a unit test implementation (+) Added IProcessService to run processes from a viewmodel with directly using the process class (which makes it easier to unit test view models) (*) If the HasErrors property of DataObjec...NodeXL: Network Overview, Discovery and Exploration for Excel: NodeXL Excel Template, version 1.0.1.160: The NodeXL Excel template displays a network graph using edge and vertex lists stored in an Excel 2007 or Excel 2010 workbook. What's NewThis release improves NodeXL's Twitter and Pajek features. See the Complete NodeXL Release History for details. Installation StepsFollow these steps to install and use the template: Download the Zip file. Unzip it into any folder. Use WinZip or a similar program, or just right-click the Zip file in Windows Explorer and select "Extract All." Close Ex...Kooboo CMS: Kooboo CMS 3.0 CTP: Files in this downloadkooboo_CMS.zip: The kooboo application files Content_DBProvider.zip: Additional content database implementation of MSSQL, RavenDB and SQLCE. Default is XML based database. To use them, copy the related dlls into web root bin folder and remove old content provider dlls. Content provider has the name like "Kooboo.CMS.Content.Persistence.SQLServer.dll" View_Engines.zip: Supports of Razor, webform and NVelocity view engine. Copy the dlls into web root bin folder to enable...UOB & ME: UOB ME 2.6: UOB ME 2.6????: ???? V1.0: ???? V1.0 ??Password Generator: 2.2: Parallel password generation Password strength calculation ( Same method used by Microsoft here : https://www.microsoft.com/protect/fraud/passwords/checker.aspx ) Minor code refactoringVisual Studio 2010 Architecture Tooling Guidance: Spanish - Architecture Guidance: Francisco Fagas http://geeks.ms/blogs/ffagas, Microsoft Most Valuable Professional (MVP), localized the Visual Studio 2010 Quick Reference Guidance for the Spanish communities, based on http://vsarchitectureguide.codeplex.com/releases/view/47828. Release Notes The guidance is available in a xps-only (default) or complete package. The complete package contains the files in xps, pdf and Office 2007 formats. 2011-01-24 Publish version 1.0 of the Spanish localized bits.ASP.NET MVC Project Awesome, jQuery Ajax helpers (controls): 1.6.2: A rich set of helpers (controls) that you can use to build highly responsive and interactive Ajax-enabled Web applications. These helpers include Autocomplete, AjaxDropdown, Lookup, Confirm Dialog, Popup Form, Popup and Pager the html generation has been optimized, the html page size is much smaller nowFacebook Graph Toolkit: Facebook Graph Toolkit 0.6: new Facebook Graph objects: Application, Page, Post, Comment Improved Intellisense documentation new Graph Api connections: albums, photos, posts, feed, home, friends JSON Toolkit upgraded to version 0.9 (beta release) with bug fixes and new features bug fixed: error when handling empty JSON arrays bug fixed: error when handling JSON array with square or large brackets in the message bug fixed: error when handling JSON obejcts with double quotation in the message bug fixed: erro...Microsoft All-In-One Code Framework: Visual Studio 2008 Code Samples 2011-01-23: Code samples for Visual Studio 2008New ProjectsAnaida - WebSocket Client/Adapter: Anaida is a WebSocket Client Library/Adapter. With 3 versions for Java, Silverlight and C#CutPasteAssign: Visual Studio extension to assist in the common refactoring of assigning parameters to local variables.Drori Photos: Photos of Drori the photographerD-Solution: App de D-SolutionEnigma Home Inventory: Most consumers do not have an itemized list of proof of ownership. Enigma Home Inventory may take the hassle out of arguing with the insurance companies. This project is aimed to be for a simple inventory program for end users who are not computer savvy.FastKnow: is a CMS & wikiFileSignatures: FileSignatures aims to create a class library that can identify the file format based on file contents. The project is written in C# 3.0, and can be used in .NET 3.5 and 4.0 projects.Genrsis: The aim of the Genrsis project is to be a suite of products that you can use to build things, starting with a workflow-based project management tool. Built in C#, it should be a one-stop place to get well-integrated products to get you up and running.MVC Demos: MVC 2 and MVC 3 examples with ajax and json.MVC Templates for DevExpress: Scaffolding templates for use in ASP.NET MVC 2 with DevExpress MVC Extensions for ASP.NET MVCPixel Replacer: The Pixel Replacer is a simple library for replacing pixel colors with a new color, by setting a filter rule.ReviewPal - The Code Review Companion for .Net.: ReviewPal, the Code Review Companion for .Net. This is an Add-In / Extension for Visual Studio 2008 & Visual Studio 2010. The aim of the Add-In / Extension is to do a source code review within the Visual Studio IDE where code makes more sense and most readable.SMVector3: Vector3 class implemented as float array or with SIMD instructions with the same interface so it is transparant whether you decide to use one version or another. You can also chance version during the life cycle of the projects.uRibbon - Office 2007 Ribbon control for VB.NET: Office 2007 ribbon control, with Orb and graphic transitions. After searching for many day looking for an Office 2007-like ribbon bar, I finally gave up and decided to write my own. It's in decent shape as-is. But anyone interested in helping me to continue the devlopment??vtcheck: This will read a target binary and check to see if it is detected by VirusTotal.Web Scheduled Task Framework: A simple set of classes intended to allow the standalone scheduling of tasks (arbitrary code to execute) on a .net website without requiring access to the operating system.WP7 codeproject app: A Windows Phone 7 app for browsing codeproject.com.zhongjh: ?????????，???????。???????????: ???????????

  Read the article

• nginx: how do I add new site/server_name in nginx?

  - by Neo

  I'm just starting to explore Nginx on my Ubuntu 10.04. I installed Nginx and I'm able to get the "Welcome to Nginx" page on localhost. However I'm not able to add a new server_name, even when I make the changes in site-available/default file. Tried reloading/restarting Nginx, but nothing works. One interesting observation. "http://mycomputername" in browser works. So somehow there is a command like 'server_name $hostname' somewhere over-riding my rule. File: sites-available/mine.enpass server { listen 80; server_name mine.enpass ; access_log /var/log/nginx/localhost.access.log; location / { root /var/www/nginx-default; index index.html index.htm; } } File: nginx.confg user www-data; worker_processes 1; error_log /var/log/nginx/error.log; pid /var/run/nginx.pid; events { worker_connections 1024; # multi_accept on; } http { include /etc/nginx/mime.types; access_log /var/log/nginx/access.log; sendfile on; #tcp_nopush on; #keepalive_timeout 0; keepalive_timeout 65; tcp_nodelay on; gzip on; gzip_comp_level 2; gzip_proxied any; gzip_types text/plain text/css application/x-javascript text/xml application/xml application/xml+rss text/javascript; gzip_disable "MSIE [1-6]\.(?!.*SV1)"; include /etc/nginx/conf.d/*.conf; include /etc/nginx/sites-enabled/*; }

  Read the article

• Possible DNS Injection and/or SSL hijack?

  - by Anthony

  So if I go to my site without indicating the protocol, I'm taken to: http://example.org/test.php But if I go directly to: https://example.org/test.php I get a 404 back. If I go to just: https://example.org I get a totally different site (a page about martial arts). I went to the site via https not very long ago (maybe a week?) and it was fine. This is a shared server, as I understand it, and I do not have shell access, so I'm limited to the site's CPanel to do any further investigations. But when I go to: example.org:2083 I'm taken to https://example.org:2083, which, if someone has taken over the SSL port, could mean they have taken over the 2083 part as well (at least in my paranoid mind). I'm made more nervous by the fact that the cpanel login page at the above address looks very new (better, really) compared to the last time I went to it over the weekend. It's possible that wires got crossed somewhere after a system update, but I don't want to put in my name username and password in case it's a phishing attempt. Is there any way to know for sure without shell access to know for sure if someone has taken over? If I look up the IP address for the host name, the IP address matches what I have on a phpinfo page I can get to over http. If I go to the IP address directly on port 2083, I get the same login mentioned above (new and and suspiciously nice). But the SSL cert shows as good when I go this route. So if that's the case (I know the IP is right, the cert checks out, and there isn't any DNS involved), is that enough to feel safe at that point of entry? Finally, if I can safely log in via the IP, does anyone have any advice on where to check first on CPanel for why the SSL port is forwarding to a site on karate? Thanks.

  Read the article

• Enabling DNS for IPv6 infrastructure

  After successful automatic distribution of IPv6 address information via DHCPv6 in your local network it might be time to start offering some more services. Usually, we would use host names in order to communicate with other machines instead of their bare IPv6 addresses. During the following paragraphs we are going to enable our own DNS name server with IPv6 address resolving. This is the third article in a series on IPv6 configuration: Configure IPv6 on your Linux system DHCPv6: Provide IPv6 information in your local network Enabling DNS for IPv6 infrastructure Accessing your web server via IPv6 Piece of advice: This is based on my findings on the internet while reading other people's helpful articles and going through a couple of man-pages on my local system. What's your name and your IPv6 address? $ sudo service bind9 status * bind9 is running If the service is not recognised, you have to install it first on your system. This is done very easy and quickly like so: $ sudo apt-get install bind9 Once again, there is no specialised package for IPv6. Just the regular application is good to go. But of course, it is necessary to enable IPv6 binding in the options. Let's fire up a text editor and modify the configuration file. $ sudo nano /etc/bind/named.conf.optionsacl iosnet {        127.0.0.1;        192.168.1.0/24;        ::1/128;        2001:db8:bad:a55::/64;};listen-on { iosnet; };listen-on-v6 { any; };allow-query { iosnet; };allow-transfer { iosnet; }; Most important directive is the listen-on-v6. This will enable your named to bind to your IPv6 addresses specified on your system. Easiest is to specify any as value, and named will bind to all available IPv6 addresses during start. More details and explanations are found in the man-pages of named.conf. Save the file and restart the named service. As usual, check your log files and correct your configuration in case of any logged error messages. Using the netstat command you can validate whether the service is running and to which IP and IPv6 addresses it is bound to, like so: $ sudo service bind9 restart $ sudo netstat -lnptu | grep "named\W*$"tcp        0      0 192.168.1.2:53        0.0.0.0:*               LISTEN      1734/named      tcp        0      0 127.0.0.1:53          0.0.0.0:*               LISTEN      1734/named      tcp6       0      0 :::53                 :::*                    LISTEN      1734/named      udp        0      0 192.168.1.2:53        0.0.0.0:*                           1734/named      udp        0      0 127.0.0.1:53          0.0.0.0:*                           1734/named      udp6       0      0 :::53                 :::*                                1734/named   Sweet! Okay, now it's about time to resolve host names and their assigned IPv6 addresses using our own DNS name server. $ host -t aaaa www.6bone.net 2001:db8:bad:a55::2Using domain server:Name: 2001:db8:bad:a55::2Address: 2001:db8:bad:a55::2#53Aliases: www.6bone.net is an alias for 6bone.net.6bone.net has IPv6 address 2001:5c0:1000:10::2 Alright, our newly configured BIND named is fully operational. Eventually, you might be more familiar with the dig command. Here is the same kind of IPv6 host name resolve but it will provide more details about that particular host as well as the domain in general. $ dig @2001:db8:bad:a55::2 www.6bone.net. AAAA More details on the Berkeley Internet Name Domain (bind) daemon and IPv6 are available in Chapter 22.1 of Peter Bieringer's HOWTO on IPv6. Setting up your own DNS zone Now, that we have an operational named in place, it's about time to implement and configure our own host names and IPv6 address resolving. The general approach is to create your own zone database below the bind folder and to add AAAA records for your hosts. In order to achieve this, we have to define the zone first in the configuration file named.conf.local. $ sudo nano /etc/bind/named.conf.local //// Do any local configuration here//zone "ios.mu" {        type master;        file "/etc/bind/zones/db.ios.mu";}; Here we specify the location of our zone database file. Next, we are going to create it and add our host names, our IP and our IPv6 addresses. $ sudo nano /etc/bind/zones/db.ios.mu $ORIGIN .$TTL 259200     ; 3 daysios.mu                  IN SOA  ios.mu. hostmaster.ios.mu. (                                2014031101 ; serial                                28800      ; refresh (8 hours)                                7200       ; retry (2 hours)                                604800     ; expire (1 week)                                86400      ; minimum (1 day)                                )                        NS      server.ios.mu.$ORIGIN ios.mu.server                  A       192.168.1.2server                  AAAA    2001:db8:bad:a55::2client1                 A       192.168.1.3client1                 AAAA    2001:db8:bad:a55::3client2                 A       192.168.1.4client2                 AAAA    2001:db8:bad:a55::4 With a couple of machines in place, it's time to reload that new configuration. Note: Each time you are going to change your zone databases you have to modify the serial information, too. Named loads the plain text zone definitions and converts them into an internal, indexed binary format to improve lookup performance. If you forget to change your serial then named will not use the new records from the text file but the indexed ones. Or you have to flush the index and force a reload of the zone. This can be done easily by either restarting the named: $ sudo service bind9 restart or by reloading the configuration file using the name server control utility - rndc: $ sudo rndc reconfig Check your log files for any error messages and whether the new zone database has been accepted. Next, we are going to resolve a host name trying to get its IPv6 address like so: $ host -t aaaa server.ios.mu. 2001:db8:bad:a55::2Using domain server:Name: 2001:db8:bad:a55::2Address: 2001:db8:bad:a55::2#53Aliases: server.ios.mu has IPv6 address 2001:db8:bad:a55::2 Looks good. Alternatively, you could have just ping'd the system as well using the ping6 command instead of the regular ping: $ ping6 serverPING server(2001:db8:bad:a55::2) 56 data bytes64 bytes from 2001:db8:bad:a55::2: icmp_seq=1 ttl=64 time=0.615 ms64 bytes from 2001:db8:bad:a55::2: icmp_seq=2 ttl=64 time=0.407 ms^C--- ios1 ping statistics ---2 packets transmitted, 2 received, 0% packet loss, time 1001msrtt min/avg/max/mdev = 0.407/0.511/0.615/0.104 ms That also looks promising to me. How about your configuration? Next, it might be interesting to extend the range of available services on the network. One essential service would be to have web sites at hand.

  Read the article

• Getting SMB file shares working over a PPTP VPN

  - by Ben Scott

  I'm having issues getting SMB file shares working over a PPTP VPN. The server setup consists of a security device (DrayTek V3300) which passes the PPTP authentication to a SBS2003 server running RRAS. The server is the DC and provides DNS and WINS, the single NIC's name server is set to 127.0.0.1, and DHCP on the DrayTek sets the server IP as the DNS. If I create a new VPN connection in Win7, leaving everything as default apart from the server, username, password and domain, I can: ping everything by IP address resolve IPs with nslookup using their fully-qualified name, as in nslookup fileserver.mydomain.local ping machines by fully-qualified name, as in ping fileserver.mydomain.local However if I try to access a file share: within Explorer, I get "Windows cannot access ..." with "Error code: 0x80004005 Unspecified Error", using net use z: \\fileserver.mydomain.local\share, I get "System error 53 has occurred. The network path was not found." If I add the machine name to my HOSTS file I can use the file share, which is my last-ditch workaround, but I have a number of VPN users and would rather a solution that doesn't involve me trying to hand-edit system files on computers half a country away. If I set the WINS server explicitly in the connection's IPv4 settings I don't have to use the FQN to ping the machine, but that doesn't change anything else.

  Read the article

• Tips and Suggestions IP Address Re-Addressing?

  - by RSXAdmin

  Hello serverfault Universe, My ever evolving and expanding local area network is currently using a class-C address. My network consists of multiple subnets depending on site/location. 192.168.1.x is site HQ 192.168.5.x is secondary site 192.168.10.x is so on and so forth. Long story short - I have inherited this network design from the previous admin who has left the company which started off with a dozen people and now has just over 300 full time/part time employees. We do not yet have client VPN access; but we do have site to site VPN setup. My question is, in preparation for outside client access to my network via Cisco ASA, I would like to re-address the HQ site because I understand a 192.168.1.x or 192.168.0.x are not very good choices for a company subnet - it may conflict with a home user's LAN when connecting to my LAN, I believe? Through your experience, does anyone out there have any suggestions and tips on how I can proceed with re-addressing my subnets. If I designed this network I would have gone with a 10.0.0.0 (mask 255.255.255.0) so I am leaning towards changing it to fit. Thank you.

  Read the article

• Linux And NTFS Permissions

  - by VGE IT

  Trying to restrict a folder within a directory created in linux filesystem. I have changed the permissions to: root rwx, a special active directory group rwx and all others r. Upon doing so, people that are not in the special AD group can access the directory and modify files. Upon doing so the group changes to "Domain Users" when the user modifies documents within the directory. I have to manualy change the documents default group back to my AD group. I have tried to create another AD group and modify permissons to deny write access. When doing so through windows explorer, the settings seem to take affect until I go back in a look at permissions for the restricted group. No permissions show when I view for the second time. Please assist. Samba share properties [MyShare] comment = "blah blah blah" browseable = yes guest ok = no read only = no path = /xxx/xxxxx/ create mask = 0640 directory mask = 0750 admin users = @"domain\Domain Admins", @"domain\group A", @"domain\group B" valid users = @"domain\Domain Admins", @"domain\group A", @"domain\group B" nt acl support = Yes inherit acls = yes inherit owner = yes inherit permissions = yes

  Read the article

• How should I set up protection for the database against sql injection when all the php scripts are flawed?

  - by Tchalvak

  I've inherited a php web app that is very insecure, with a history of sql injection. I can't fix the scripts immediately, I rather need them to be running to have the website running, and there are too many php scripts to deal with from the php end first. I do, however, have full control over the server and the software on the server, including full control over the mysql database and it's users. Let's estimate it at something like 300 scripts overall, 40 semi-private scripts, and 20 private/secure scripts. So my question is how best to go about securing the data, with the implicit assumption that sql injection from the php side (e.g. somewhere in that list of 300 scripts) is inevitable? My first-draft plan is to create multiple tiers of different permissioned users in the mysql database. In this way I can secure the data & scripts in most need of securing first ("private/secure" category), then the second tier of database tables & scripts ("semi-private"), and finally deal with the security of the rest of the php app overall (with the result of finally securing the database tables that essentially deal with "public" information, e.g. stuff that even just viewing the homepage requires). So, 3 database users (public, semi-private, and secure), with a different user connecting for each of three different groups of scripts (the secure scripts, the semi-private scripts, and the public scripts). In this way, I can prevent all access to "secure" from "public" or from "semi-private", and to "semi-private" from "public". Are there other alternatives that I should look into? If a tiered access system is the way to go, what approaches are best?

  Read the article

• I want to add a Quality Assurance domain. How do I handle DNS servers?

  - by Tim

  I'm advising a large client on how to isolate their dev and testing from their production. They already have one domain, lets say xyz.net with the active directory domain as "XYZ01". I want to add second domain say QAxyz.net and make its active directory domain "QA01" All development and QA servers would be moved to the QAxyz.net domain, the machines would be part of the QA01 domain. Note: Some of these servers will have the same name as the production servers for testing purposes. I believe we would have separate DNS servers for each domain. If I am logged into the QA01 domain, to access the production domain I would qualify my access like so: \PRODSERVER.xyz.net login: XYZ01\username Do I need to add a forwarder to my QAxyz.net DNS server so that it can see xyz.net? Would I need to do the same to the xyz.net DNS server to see QAxyz.net? I don't know how to advise them in this. Does anyone have any other recommendations to isolationg a QA domain? Many Thanks in advance! Tim

  Read the article

• Nginx configuration question

  - by Pockata

  Hey guys, i'm trying to make the autoindex feature only run for my ip address with this code: server{ ... autoindex off; ... if ($remote_addr ~ ..*.*) { autoindex on; } ... } But it doesn't work. It gives my a 403 :/ Can someone help me :) Btw, i'm using Debian Lenny and Nginx 0.6 :) EDIT: Here's my full configuration: server { listen 80; server_name site.com; server_name_in_redirect off; client_max_body_size 4M; server_tokens off; # log_subrequest on; autoindex off; # expires max; error_page 500 502 503 504 /var/www/nginx-default/50x.html; # error_page 404 /404.html; set $myhome /bla/bla; set $myroot $myhome/public; set $mysubd $myhome/subdomains; log_format new_log '$remote_addr - $remote_user [$time_local] $request ' '"$status" "$http_referer" ' '"$http_user_agent" "$http_x_forwarded_for"'; # Star nginx :@ access_log /bla/bla/logs/access.log new_log; error_log /bla/bla/logs/error.log; if ($remote_addr ~ 94.156.58.138) { autoindex on; } # Subdomains if ($host ~* (.*)\.site\.org$) { set $myroot $mysubd/$1; } # Static files # location ~* \.(jpg|jpeg|gif|css|png|js|ico)$ { # access_log off; # expires 30d; # } location / { root $myroot; index index.php index.html index.htm; } # PHP location ~ \.php$ { fastcgi_pass 127.0.0.1:9000; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME $myroot$fastcgi_script_name; include fastcgi_params; } # .Htaccess location ~ /\.ht { deny all; } } I forgot to mention that when i add the code to remove static files from my access log, the static files cannot be accessed. I don't know if it's relevant :)

  Read the article

• Affordable combined Ruby/Rails/Redmine + Subversion hosting?

  - by Pekka

  I'm a self employed web developer and after nine years of hard work, I'm looking to become a bit more "vagrant" starting next year, do some much-needed traveling and a bit and work off and on, making use of one of the greatest advantages of a programming job: The ability to work virtually from everywhere. For that, I am looking for a reliable hosting company I can entrust my code to in the form of a number of Subversion repositories, and an installation of the Redmine project management tool. As my financial situation may vary during traveling, I am looking for something I can pay up front for a year or two, and is obviously not too pricey. I don't care where the company is located, as long as it's trustworthy and solid, meaning it's not likely to go out of business next month. Does anybody know good recommendations? Preferably from own, personal, good experience. I have looked at CVSDude / Codesion and while they are certainly great, they don't offer Redmine of course, and seem to be aiming toward bigger organizations mainly. What I would need: 2-5 Gigs of space minimum, freely distributable between SVN, and Redmine attachments Unlimited number of Subversion projects Access control (team members / checkout-only accounts / etc.) I don't mind configuring the svn settings on file basis myself I need the possibility to map a custom domain to the package that is hosted elsewhere Frequent backups and access to those backups through FTP or other means I have been running my own virtual server for this until now, but I don't want the hassle, especially on the security side, while I may not always have the internet connection to fix problems that may come up.

  Read the article

• Windows and file system abstraction - how much does it matter where something comes from?

  - by deceze

  I have come across the following phenomenon and would like to know how leaky Windows' file system abstraction is or if there's something else involved. I partitioned the hard disk of my MacBook Pro and installed Windows 7 (64 bit). The Bootcamp driver package includes file system drivers (right term?) that enable Windows to access the Mac OS HFS+ partition. AFAIK it's a read-only access, but it works. Now, I have some disk images of stuff I usually install, so I grabbed a copy of Daemon Tools to mount them. When I mount an image saved on the HFS+ partition, about two out of three installers on these disks (usually InstallShield) crash with all sorts of weird errors. Most are just gibberish that lead to all sorts of non-solutions on Google, one was "This application is not the right type for your computer, check if you need 32 or 64 bit versions." When moving the image files to another Windows 7 computer on the network and mounting them from the network share, they work fine. My question now is, why do applications behave differently depending on whether the read-only image file, which should be abstracted away through the read-only virtual Daemon Tools drive, is located on a read-only HFS+ partition or on a Windows network share? And I'll just roll this into the question as well since I was wondering: Does the file system of a network share matter? Does the client system need to understand the file system of the share host or is that abstracted away in SMB?

  Read the article

• Apache HTTPd FollowSymLinks path permission

  - by apast

  Hi, I'm configuring my development environment with a basic Apache HTTPd configuration. But, to avoid a often problem, I want to map my test URL to my development folder. I'm using Ubuntu. My development path is located under the following example path: /home/myusername/myworkspace/hptargetpath/src/pages Considering the following symbolic link mapping: #ls -l /opt/share/www/mydevelopmentrootpath: lrwxrwxrwx 1 root root 77 2011-02-13 18:53 /opt/share/www/mydevelopmentrootpath -> /home/myusername/myworkspace/hptargetpath/src/pages With this folder mapping, I configured Apache HTTPd with the following configuration: <VirtualHost *:*> ServerName local.server.com ServerAdmin [email protected] DirectoryIndex index.html DocumentRoot /opt/share/www/mydevelopmentrootpath <Directory /opt/share/www/mydevelopmentrootpath/ > Options +Indexes Options +FollowSymLinks AllowOverride None Order allow,deny Allow from all </Directory> </VirtualHost> But, I'm receiving a 403 Forbidden error when I want to access index.html under the address http://local.server.com/index.html. 403 Forbidden You don't have permission to access /index.html on this server. On httpd debug log, I checked the following message: [Sun Feb 13 19:34:47 2011] [error] [client 127.0.1.1] Symbolic link not allowed or link target not accessible: /opt/share/www/mydevelopmentrootpath I'm thinking that this problem is been generated by some path permission. It's not a direct permission to directory, but some intermediate directory in the path. There's a directive on httpd core Options: SymLinksIfOwnerMatch The server will only follow symbolic links for which the target file or directory is owned by the same user id as the link. But, I tested it without effects. Somebody may help me? I think that it's a trivial configuration on development environment. Best regards, And Past

  Read the article

• How do I set up a Windows NFS share so that I can view it's contents on Linux?

  - by hewhocutsdown

  My NFS server is a Windows XP SP3 box with the Microsoft Windows Services for Unix installed. I have a share configured under C:\NFS with the share name NFS and ANSI encoding. Anonymous access is enabled, with the anon UID/GID set to 0/0. Additionally, I've set ALL MACHINES to Read-Write, and checked the checkbox to Allow root access. My first NFS client is a Ubuntu 10.04 box, with nfs-common installed. Running sudo mount -t nfs 1.1.1.1:/NFS /home/user/NFS succeeds, but when I attempt to view the folder (even as root), it tells me that I do not have the permissions necessary to view the contents of the folder. My second NFS client is an IBM iSeries box running OS/400 V5R3. I used the mount command below: MOUNT TYPE(*NFS) MFS('1.1.1.1:/NFS') MNTOVRDIR('/PARENT/NFS') OPTIONS('rw,nosuid,retry=5,rsize=8096,wsize=8096,timeo=20,retrans=2,acregmin=30,acregmax=60,acdirmin=30,acdirmax=60,soft') CODEPAGE(*BINARY *ASCII) which also mounts successfully. Attempting to WRKLNK '/PARENT/NFS' and use Option 5 to enter the directory yields a Not authorized to object error - even though I am a security officer with the *ALLOBJ special authority. My gut says that it's a problem with the Windows share, but I don't know what it could be. Do you have any suggestions?

  Read the article

• Registry remotley hacked win 7 need help tracking the perp

  - by user577229

  I was writing some .VBS code at thhe office that would allow certain file extensions to be downloaded without a warning dialog on a w7x32 system. The system I was writing this on is in a lab on a segmented subnet. All web access is via a proxy server. The only means of accessing my machine is via the internet or from within the labs MSFT AD domain. While writing and testing my code I found a message of sorts. Upon refresing the registry to verify my code changed a dword, instead the message HELLO was written and visible in regedit where the dword value wass called for. I took a screen shot and proceeded to edit my code. This same weird behavior occurred last time I was writing registry code except on another internal server. I understand that remote registry access exists for windows systems. I will block this immediately once I return to the office. What I want to know is, can I trace who made this connection? How would I do this? I suspect the cause of this is the cause of other "odd" behaviors I'm experiencing at work such as losing control of my input director master control for over an hour and unchanged code that all of a sudden fails for no logical region. These failures occur at funny times, whenver I'm about to give a demonstration of my test code. I know this sounds crazy however knowledge of the registry component makes this believable. Once the registry can be accessed, the entire system is compromised. Any help or sanity checking is appreciated.

  Read the article

• Ubuntu 12.04 suddenly cannot connect to WPA2/WPA Personal protected connection. Windows 7 can

  - by d4ryl3

  I have a laptop with Windows 7 and Ubuntu 12.04. I have a Cisco E1200 and when I set it up, it created 2 SSIDs. Let's name them: MyConnection (WPA/WPA2 personal), and MyConnection-Guest (no authentication, guest password entered via web browser). I had no problem connecting to MyConnection before, either in Windows 7 and Ubuntu. But now, I can't access MyConnection on Ubuntu. It just says "connecting..." then disconnects after a while. But I'm able to access the internet (on Ubuntu) when I connect to MyConnection-Guest. MAC filtering is off (even if it's on its MAC address is in the white list). Any idea why I'm unable to connect to MyConnection in Ubuntu? Thanks. Update: My Ubuntu installation can connect to ANY WiFi connection (WPA/WEP/no auth), except for MyConnection. Update2: This is what "The not so easy way" returned: Initializing interface 'eth1' conf '/etc/wpa_supplicant.conf' driver 'default' ctrl_interface 'N/A' bridge 'N/A' Configuration file '/etc/wpa_supplicant.conf' -> '/etc/wpa_supplicant.conf' Reading configuration file '/etc/wpa_supplicant.conf' Priority group 0 id=0 ssid='MyConnection' id=1 ssid='MyConnection' id=2 ssid='MyConnection' id=3 ssid='MyConnection' WEXT: cfg80211-based driver detected SIOCGIWRANGE: WE(compiled)=22 WE(source)=21 enc_capa=0xf capabilities: key_mgmt 0xf enc 0xf flags 0x0 netlink: Operstate: linkmode=1, operstate=5 Own MAC address: xx:xx:xx:xx:xx:xx wpa_driver_wext_set_key: alg=0 key_idx=0 set_tx=0 seq_len=0 key_len=0 wpa_driver_wext_set_key: alg=0 key_idx=1 set_tx=0 seq_len=0 key_len=0 wpa_driver_wext_set_key: alg=0 key_idx=2 set_tx=0 seq_len=0 key_len=0 wpa_driver_wext_set_key: alg=0 key_idx=3 set_tx=0 seq_len=0 key_len=0 wpa_driver_wext_set_key: alg=0 key_idx=4 set_tx=0 seq_len=0 key_len=0 ioctl[SIOCSIWENCODEEXT]: Invalid argument Driver did not support SIOCSIWENCODEEXT wpa_driver_wext_set_key: alg=0 key_idx=5 set_tx=0 seq_len=0 key_len=0 ioctl[SIOCSIWENCODEEXT]: Invalid argument Driver did not support SIOCSIWENCODEEXT wpa_driver_wext_set_countermeasures RSN: flushing PMKID list in the driver Setting scan request: 0 sec 100000 usec WPS: UUID based on MAC address - hexdump(len=16): 16 3b d8 47 9e 24 50 89 96 16 6d 66 35 f3 58 37 EAPOL: SUPP_PAE entering state DISCONNECTED EAPOL: Supplicant port status: Unauthorized EAPOL: KEY_RX entering state NO_KEY_RECEIVE EAPOL: SUPP_BE entering state INITIALIZE EAP: EAP entering state DISABLED EAPOL: Supplicant port status: Unauthorized EAPOL: Supplicant port status: Unauthorized Added interface eth1

  Read the article

• pfSense Load Balancer and Virtual IP

  - by jshin47

  I have two identical web servers on 10.2.1.13 and 10.2.1.113. I would like to set up pfSense load balancer to balance requests to both of these. I set up pools that included HTTP and HTTPS for both of these hosts, then set up virtual servers that responded on HTTP and HTTPS and referred traffic to its respective pool. However, I set up the virtual server to listen on 10.2.1.213, a LAN IP rather than a WAN IP, because I want LAN traffic to be able use the load balancer virtual server as well. So, I set up a Virtual IP for 10.2.1.213 on LAN IP, and a NAT port forwarding rule for HTTP and HTTPS traffic on a WAN IP to forward to 10.2.1.213. It seems like this should work, but it fails. What eventually happens is that when I try to access the page from WAN, I am directed to the login page for my pfSense device rather than the page I am expecting. When I try to access 10.2.1.213 from LAN, the request times out. What is going wrong here? I have tried it with and without NAT reflection to no avail. Please advise

  Read the article

• "Server Unavailable" and removed permissions on .NET sites after Windows Update

  - by tags2k

  Our company has five almost identical Windows 2003 servers with the same host, and all but one performed an automatic Windows Update last night without issue. The one that had problems, of course, was the one which hosts the majority of our sites. What the update appeared to do was cause the NETWORK user to stop having access to the .NET Framework 2.0 files, as the event log was complaining about not being able to open System.Web. This resulted in every .NET site on the server returning "Server Unavailable" as the App Domains failed to be initialise. I ran aspnet_regiis which didn't appear to fix the problem, so I ran FileMon which revealed that nobody but the Administrators group had access to any files in any of the website folders! After resetting the permissions, things appear to be fine. I was wondering if anyone had an idea of what could have caused this to go wrong? As I say, the four other servers updated without a problem. Are there any known issues involved with any of the following updates? My major suspect at the moment is the 3.5 update as all of the sites on the server are running in 3.5. Windows Server 2003 Update Rollup for ActiveX Killbits for Windows Server 2003 (KB960715) Windows Server 2003 Security Update for Internet Explorer 7 for Windows Server 2003 (KB960714) Windows Server 2003 Microsoft .NET Framework 3.5 Family Update (KB959209) x86 Windows Server 2003 Security Update for Windows Server 2003 (KB958687) Thanks for any light you can shed on this.

  Read the article

• Explorer.exe keeps crashing during log in

  - by asif

  I have got a weird problem. My windows 7 has two user accounts (both are administrator). I can log in to one account and do all sort of work. But whenever I try to log in to other account, it shows a blank screen and a messagebox pops up with "windows explorer has stopped working". The options available are: Close the program Check online for a solution and close the program The problem signature is as follows: Problem Event Name: InPageError Error Status Code: c000009c Faulting Media Type: 00000003 OS Version: 6.1.7601.2.1.0.256.1 Locale ID: 1033 Additional Information 1: 0a9e Additional Information 2: 0a9e372d3b4ad19135b953a78882e789 Additional Information 3: 0a9e Additional Information 4: 0a9e372d3b4ad19135b953a78882e789 If I press alt+ctrl+del and then select start task manager, it also crashes. I can not run any program using runas command (from good profile) too. The task manager and runas programs all show same problem signature. I read the similar question and followed all the steps, but no luck. Later, I viewed the event log and found that, explorer.exe could not access a file. I checked the location but the file is there. The actual message is: Windows cannot access the file C:\Users\testuser\AppData\Local\Microsoft\Windows\Caches\{AFBF9F1A-8EE8-4C77-AF34-C647E37CA0D9}.1.ver0x0000000000000020.db for one of the following reasons: there is a problem with the network connection, the disk that the file is stored on, or the storage drivers installed on this computer; or the disk is missing. Windows closed the program Windows Explorer because of this error. The question is, how can I resolve this issue? Should I just delete the file or replace it with another one to stop explorer.exe from crashing? offtopic: What is the content of this file and why it is necessary?

  Read the article

• Piecing together low-powered hardware for an RS-232 terminal server

  - by Fred

  I'm working on reconstructing my Cisco lab for training/educational purposes and I found that the actual terminal server I have is dead. I have a couple of 8-port PCI serial cards which would be more than ample for my lab, but I don't want to leave my personal computer running to be able to access the console ports. Ideally I would access the terminal server remotely, either by SSH/RDP to the box (depending on what OS I go with) or by installing a software package that allows me to telnet directly to a serial port. I know I've found a program that does this under Linux in the past but its name escapes me at the moment. I'm thinking about scavenging for some old hardware, on eBay or something, to put together a low-powered PC. Needs to be something that: Has Low-power consumption Has at least 2 PCI slots (though I certainly wouldn't complain about having more) Has onboard Ethernet (or, if not, another PCI or ISA slot (not shared)) Can be headless once an OS installed (probably Linux) I'm currently leaning towards an old fashioned Pentium (sub-133MHz era) but I am wondering if anybody else knows of another platform/mobo that would suit these needs. Alternatively, I've been considering buying a Raspberry Pi and a big USB hub along with a bunch of USB-Serial adapters but this sounds like it'd get messy quick with cables and adapters all over the place, and I may not even have the same ttyS#'s between boots.

  Read the article

• GNU screen cannot find terminfo entry on HP-UX

  - by Ency

  I am trying to make screen work on HP-UX B.11.23 U ia64 0308561483 unlimited-user license. Please notice I do not have root access. I have already compiled screen successfully, configured with LIBS=-lcurses. When I try to start screen it wrotes Cannot find terminfo entry for 'xterm'. But there ARE terminfos for the terminal type in screen-4.0.3> ls -a /usr/share/lib/terminfo/x/ . .. x-hpterm x1700 x1720 x1750 xitex xl83 xterm xterms I thing the problem may be there are in non-standard path, because according to man page standard path is /usr/lib/terminfo/?/* What I tried: But as I said I do not have root access so cant make symlink, anyway I tried run screen with filled TERMINFO_DIRS (TERMINFO_DIRS=/usr/share/lib/terminfo/x/ ./screen and TERMINFO_DIRS=/usr/share/lib/terminfo/ ./screen) but none of them work - same error. Change TERM to different values - same error Cannot find terminfo entry for <WHATEVER WHAT WAS IN TERM VAR>. Put something into screenrc and run ./screen -c screenrc screen-4.0.3> cat screenrc attrcolor b ".I" term xterm termcap xterm* LP:hs@ termcapinfo xterm 'Co#256:AB=\E[48;5;%dm:AF=\E[38;5;%dm' defbce "on" But no luck so far, have you got any suggestions? Need some additional information, let me know.

  Read the article

< Previous Page | 624 625 626 627 628 629 630 631 632 633 634 635  | Next Page >