Search Results

Search found 19093 results on 764 pages for 'max path'.

Page 633/764 | < Previous Page | 629 630 631 632 633 634 635 636 637 638 639 640  | Next Page >

• Best NIC config when virtual servers need iSCSI storage?

  - by icky2000

  I have a Windows 2008 server running Hyper-V. There are 6 NICs on the server configured like this: NIC01 & NIC02: teamed administrative interface (RDP, mgmt, etc) NIC03: connected to iSCSI VLAN #1 NIC04: connected to iSCSI VLAN #2 NIC05: dedicated to one virtual switch for VMs NIC06: dedicated to another virtual switch for VMs The iSCSI NICs are used obviously for storage to host the VMs. I put half the VMs on the host on the switch assigned to NIC05 and the other half on the switch assigned to NIC06. We have multiple production networks that the VMs could appear on so the switch ports that NIC05 & NIC06 are connected to are trunked and we then tag the NIC on the VM for the appropriate VLAN. No clustering on this host. Now I wish to assign some iSCSI storage direct to a VM. As I see it I have 2 options: Add the iSCSI VLANs to the trunked ports (NIC05 and NIC06), add two NICs to the VM that needs iSCSI storage, and tag them for the iSCSI VLANs Create two additional virtual switches on the host. Assign one to NIC03 and one to NIC04. Add two NICs to the VM that needs iSCSI storage and let them share that path to the SAN with the host. I'm wondering about how much overhead the VLAN tagging in Hyper-V has and haven't seen any discussion about that. I'm also a bit concerned that something funky on the iSCSI-connected VM could saturate the iSCSI NICs or cause some other problem that could threaten storage access for the entire host which would be bad. Any thoughts or suggestions? How do you configure your hosts when VMs connect direct to iSCSI?

  Read the article

• Standards for documenting/designing infrastructure

  - by Paul

  We have a moderately complex solution for which we need to construct a production environment. There are around a dozen components (and here I'm using a definition of "component" which means "can fail independently of other components" - e.g. an Apache server, a Weblogic web app, an ftp server, an ejabberd server, etc). There are a number of weblogic web apps - and one thing we need to decide is how many weblogic containers to run these web apps in. The system needs to be highly available, and communications in and out of the system are typically secured by SSL Our datacentre team will handle things like VLAN design, racking, server specification and build. So the kinds of decisions we still need to make are: How to map components to physical servers (and weblogic containers) Identify all communication paths, ensure all are either resilient or there's an "upstream" comms path that is resilient, and failover of that depends on all single-points of failure "downstream". Decide where to terminate SSL (on load balancers, or on Apache servers, for instance). My question isn't really about how to make the decisions, but whether there are any standards for documenting (especially in diagrams) the design questions and the design decisions. It seems odd, for instance, that Visio doesn't have a template for something like this - it has templates for more physical layout, and for more logical /software architecture diagrams. So right now I'm using a basic Visio diagram to represent each component, the commms between them with plans to augment this with hostnames, ports, whether each comms link is resilient etc, etc. This all feels like something that must been done many times before. Are there standards for documenting this?

  Read the article

• make pentaho report for ubuntu 11.04

  - by Hendri

  currently i'm trying to install Pentaho Reports for OpenERP which is refer from https://github.com/WillowIT/Pentaho-...rver/build.xml i ever installed on some laptops which is Windows Based and it's working, but currently i'm trying on UBuntu 11.04 OS, it prompted me error like this "error build.xml:18: failed to create task or type.." below is the steps i did : 1. install java-6-openjdk comment : "apt-get install java-6-openjdk" then i set installed java jdk into java_home environment command: "nano /etc/environment" add environment with this new line : JAVA_HOME="/usr/lib/jvm/java-6-openjdk" I install apache ant command : "apt-get install ant" followed by setting the evnironment command: "nano /etc/environment" add environment with this new line : ANT_HOME="/usr/share/ant" try to check installation with command "ant"... I get message like this: Buildfile: build.xml does not exist! Build failed then download java server from https://github.com/WillowIT/Pentaho-...rver/build.xml and then copied to Ubuntu share folder and then on command form, i goto extracted path which is share folder i mentioned and executed command "ant war " and i got error message : BUILD FAILED /share/java_server/build.xml:18: problem: failed to create task or type antlibrg:apacge.ivy.ant:retrieve cause: The name is undefined. Action:Check the spelling. Action:Check that any custom taks/types have been declared Action:Check that any /declarations have taken place. No types or taks have been defined in this namespace yet This appears to be an antlib declaration. Action:Check that the implementing library exists in one of: -/usr/share/ant/lib -/root/.ant/lib -a directory added on the command line with the -lib argument Total time:0 seconds is there any compability issue? or i miss out some steps? i'm in the some project to rush with for reporting, so please help me to solve this issue i look forward to your corporation to help me solve this issue, thanks a lot in advance Thx Best Regards,

  Read the article

• How to remotely connect using perfmon?

  - by user36914

  Suprised there is not a ton of information on google when i search for this but there is not. Lot of people asking the question but i none of them have any good answers. I have a remote computer running hyper-v (server) running a Windows 7 x64 guest (guest). Occasionally i won't be able to remote desktop to guest. I will then remote to server and see that the guest instance is constantly using about 25% of the cpu. WHen i try to connect directly from server i will get the login screen but as soon as i type the password in it will just stay at the windows 7 login screen but the account names will disappear and it will not log in. It responds to pings though. I don't know how else to diagnose other than trying to run perfmon remotely. It only happens like every 3 weeks and i run it 24/7. So i'm trying to run remote desktop remotely. I tested this out on a local vm i have running under vmware. When i try to connect using perfmon to my local vm i get this error: "when attempting to connect to the remote computer the4 following system error occurred: the network path was not found" I found in another past to start the remote registry service and when i start the service i get this error: "No such interface supported" Anyways, how do i remotely connect to another machine with perfmon or if anyone has a better idea how i can diagnose the problem above then let me know.

  Read the article

• GUI interfaces to ATI card behave weirdly out of the box and after updates.

  - by jdk

  My Lenovo W500 came with an ATI Mobility FireGL V5700 and both the Catalyst control center software and Vista display manager display four monitors. What's really annoying is the behaviour. My two active displays (laptop display + my external monitor) are always #s 3 and 4 respectively which doesn't make sense. This is out of the box. Additionally dragging & dropping is jumpy and displays #1 and 2 (always inactive because they don't exist to the software) are often preventing me from dragging #3 and 4 to the rightmost side. They also auto-snap to weird positions and certain sensible positions like position one directly over top of the other are not possible. The exact same annoyances are present when using the Windows Display manager too. In other words the interface is crap and I'm looking for a fix that's not wishing I had gone with nVidia instead. I've updated drivers, and Catalyst control centre. Have latest Windows and AMD/ATI updates. Any thoughts? Graphics Software Driver Packaging Version 8.563.2.1-090401a-079160C-Lenovo Provider ATI Technologies Inc. 2D Driver Version 7.01.01.849 2D Driver File Path /REGISTRY/MACHINE/SYSTEM/ControlSet001/Control/Class/{4D36E968-E325-11CE-BFC1-08002BE10318}/0001 Direct3D Version 7.14.10.0630 OpenGL Version 6.14.10.8306 Catalyst® Control Center Version 2009.0401.1328.22301 Graphics Hardware Primary Adapter Graphics Card Manufacturer Powered by ATI Graphics Chipset ATI Mobility FireGL V5700 Device ID 9591 Vendor 1002 Subsystem ID 2126 Subsystem Vendor ID 17AA Graphics Bus Capability PCI Express 2.0 Maximum Bus Setting PCI Express 2.0 x16 BIOS Version 010.088.000.021 BIOS Part Number BK-ATI VER010.088.000.021.034663 BIOS Date 2009/09/30 Memory Size 512 MB Memory Type DDR3 Core Clock in MHz 600 MHz Memory Clock in MHz 700 MHz

  Read the article

• apt-mirror does not mirror the i18n directory

  - by Fred

  I need to setup a local Ubuntu mirror so the whole network doesn't need to hit remote servers in order to update and install new packages. Following a brief tutorial found here, I managed to get a server up and running that correctly mirrors packages from the main and restricted categories. However, when I call apt-get update on a client, I get a couple of errors such as : Ign http://192.168.1.18 karmic/main Translation-fr Ign http://192.168.1.18 karmic/restricted Translation-fr Checking back on the server, I see that apt-mirror only took the binary-amd64 directory of the mirror, and didn't take i18n that would provide Translation-fr. The manpage for apt-mirror doesn't say anything about i18n, and Google is of no help either. How do I properly mirror i18n? My current mirror.list file is as follows : ############# config ################## # # set base_path /var/spool/apt-mirror # # if you change the base path you must create the directories below with write privileges # # set mirror_path $base_path/mirror # set skel_path $base_path/skel # set var_path $base_path/var # set cleanscript $var_path/clean.sh # set defaultarch <running host architecture> # set postmirror_script $var_path/postmirror.sh set run_postmirror 0 set nthreads 20 set _tilde 0 # ############# end config ############## deb http://mirror.cc.columbia.edu/pub/linux/ubuntu/archive karmic main restricted deb http://mirror.cc.columbia.edu/pub/linux/ubuntu/archive karmic-updates main restricted clean http://mirror.cc.columbia.edu/pub/linux/ubuntu/archive

  Read the article

• logrotate: neither rotate nor compress empty files

  - by Andrew Tobey

  i have just set up an (r)syslog server to receive the logs of various clients, which works fine. only logrotate is still not behaving as intending. i want logrotate to create a new logfile for each day, but only to keep and store i.e. compress non-empty files. my logrotate config looks currently like this # sample configuration for logrotate being a remote server for multiple clients /var/log/syslog { rotate 3 daily missingok notifempty delaycompress compress dateext nomail postrotate reload rsyslog >/dev/null 2>&1 || true endscript } # local i.e. the system's very own logs: keep logs for a whole month /var/log/kern.log /var/log/kernel-info /var/log/auth.log /var/log/auth-info /var/log/cron.log /var/log/cron-info /var/log/daemon.log /var/log/daemon-info /var/log/mail.log /var/log/rsyslog /var/log/rsyslog-info { rotate 31 daily missingok notifempty delaycompress compress dateext nomail sharedscripts postrotate reload rsyslog >/dev/null 2>&1 || true endscript } # received i.e. logs from the clients /var/log/path-to-logs/*/* { rotate 31 daily missingok notifempty delaycompress compress dateext nomail } what i end up with is having is some sort of "summarized" files such as filename-datestampDay-Day and corresponding .gz files. What I do have are empty files, which are eventually zipped. so does the notifempty directive is in fact responsible for these DayX-DayY files, days on which really nothing happened? what would be an efficient way to drop both, empty log files and their .gz files, so that I eventually only keep logs/compressed files that truly contain data?

  Read the article

• I have a NGINX server configured to work with node.js, but many times a file of 1.03MB of js is not loaded by various browser and various pc

  - by Totty

  I'm using this in a local LAN so it should be quite fast. The nginx server use the node.js server to serve static files, so it must pass throught node.js to download the files, but that is not a problem when I'm not using the nginx. In chrome with debugger on I can see that the status is: 206 - partial content and it only has downloaded 31KB of 1.03MB. After 1.1 min it turns red and the status failed. Waiting time: 6ms Receiving: 1.1 min The headers in google chrom: Request URL:http://192.168.1.16/production/assembly/script/production.js Request Method:GET Status Code:206 Partial Content Request Headersview source Accept:*/* Accept-Charset:ISO-8859-1,utf-8;q=0.7,*;q=0.3 Accept-Encoding:gzip,deflate,sdch Accept-Language:pt-PT,pt;q=0.8,en-US;q=0.6,en;q=0.4 Connection:keep-alive Cookie:connect.sid=s%3Abls2qobcCaJ%2FyBNZwedtDR9N.0vD4Fi03H1bEdCszGsxIjjK0lZIjJhLnToWKFVxZOiE Host:192.168.1.16 If-Range:"1081715-1350053827000" Range:bytes=16090-16090 Referer:http://192.168.1.16/production/assembly/ User-Agent:Mozilla/5.0 (Windows NT 6.0) AppleWebKit/537.4 (KHTML, like Gecko) Chrome/22.0.1229.94 Safari/537.4 Response Headersview source Accept-Ranges:bytes Cache-Control:public, max-age=0 Connection:keep-alive Content-Length:1 Content-Range:bytes 16090-16090/1081715 Content-Type:application/javascript Date:Mon, 15 Oct 2012 09:18:50 GMT ETag:"1081715-1350053827000" Last-Modified:Fri, 12 Oct 2012 14:57:07 GMT Server:nginx/1.1.19 X-Powered-By:Express My nginx configurations: File 1: user totty; worker_processes 4; pid /var/run/nginx.pid; events { worker_connections 768; # multi_accept on; } http { ## # Basic Settings ## sendfile on; tcp_nopush on; tcp_nodelay on; keepalive_timeout 65; types_hash_max_size 2048; # server_tokens off; # server_names_hash_bucket_size 64; # server_name_in_redirect off; include /etc/nginx/mime.types; default_type application/octet-stream; ## # Logging Settings ## access_log /home/totty/web/production01_server/node_modules/production/_logs/_NGINX_access.txt; error_log /home/totty/web/production01_server/node_modules/production/_logs/_NGINX_error.txt; ## # Gzip Settings ## gzip on; gzip_disable "msie6"; # gzip_vary on; # gzip_proxied any; # gzip_comp_level 6; # gzip_buffers 16 8k; # gzip_http_version 1.1; # gzip_types text/plain text/css application/json application/x-javascript text/xml application/xml application/xml+rss text/javascript; ## # nginx-naxsi config ## # Uncomment it if you installed nginx-naxsi ## #include /etc/nginx/naxsi_core.rules; ## # nginx-passenger config ## # Uncomment it if you installed nginx-passenger ## #passenger_root /usr; #passenger_ruby /usr/bin/ruby; ## # Virtual Host Configs ## autoindex on; include /home/totty/web/production01_server/_deployment/nginxConfigs/server/*; } File that is included by the previous file: server { # custom location for entry # using only "/" instead of "/production/assembly" it # would allow you to go to "thatip/". In this way # we are limiting to "thatip/production/assembly/" location /production/assembly/ { # ip and port used in node.js proxy_pass http://127.0.0.1:3000/; } location /production/assembly.mongo/ { proxy_pass http://127.0.0.1:9000/; proxy_redirect off; } location /production/assembly.logs/ { autoindex on; alias /home/totty/web/production01_server/node_modules/production/_logs/; } }

  Read the article

• How to make an x.509 certificate from a PEM one?

  - by Ken

  I'm trying to test a script, locally, which involves uploading a file using a Java-based program to a FileZilla FTPES server. For the real thing, there is a real certificate on the FZ server, and the upload step (tested alone) seems to work fine. I've installed FileZilla Server on my dev box (so it'll test uploading from localhost to localhost). I don't have a real certificate for it, of course, so I used the "Generate new certificate..." button in FZ. It works fine from an interactive FTPES program (as long as I OK the unknown cert), but from my Java program it throws a javax.net.ssl.SSLHandshakeException ("unable to find valid certification path to requested target"). So how do I tell Java that this certificate is OK with me? (I know there's a way to change the Java program to accept any certificate, but I don't want to go down that route. I want to test it just as it will happen in production, and I don't want to ignore unknown certificates in production.) I found that Java has a program called "keytool" that seems to be for managing this sort of thing, but it complains that the certificate file that FZ generated is not an "x.509" file. A posting from the FZ side said it was "PEM encoded". I have "openssl" here, which looks like it's perfect for converting between certificate formats, but I think my understanding of certificate formats is wrong because I'm not seeing anything obvious. My knowledge of security certificates is a bit shaky, so if my title is stupidly wrong, please help by fixing that. :-)

  Read the article

• IIS 7, FastCGI, PHP and custom php.ini files

  - by Marlon

  I'm running PHP 5.3, FastCGI, and IIS 7 on Windows Server 2008. I have a site which I would like to configure its own php.ini settings for but things aren't working as expected. I am following the tutorial located here. This is what I have done so far: 1) Configured a new website with it's own AppPool. 2) Selected PHP 5.3.6 from the PHP Manager available on the website home on IIS (not the web server home which sets the global version of PHP) 3) Added the following lines to the section of the applicationHost.config file located at system32/inetsrv/config <application fullPath="C:\Program Files (x86)\PHP\v5.3\php-cgi.exe" arguments="-d open_basedir=C:\inetpub\wwwroot\kickasswebsite.com" maxInstances="4" idleTimeout="300" activityTimeout="30" requestTimeout="90" instanceMaxRequests="200" protocol="NamedPipe" queueLength="1000" flushNamedPipe="false" rapidFailsPerMinute="10"> <environmentVariables> <environmentVariable name="PHPRC" value="c:\inetpub\wwwroot\kickasswebsite.com" /> </environmentVariables> </application> 4) I then create a php.ini file located in C:\inetpub\wwwroot\kickasswebsite.com (the location of the root of the website) register_globals = on 5) I then run test.php which simply outputs everything the method call to phpinfo() returns. At this point, I observe that the global setting for register_globals = off (as it should be), but the local setting for register_globals = off, even though I specified it differently in the php.ini file I created at the root of the site. Furthermore, I see these settings in the output of the php.ini Configuration File (php.ini) Path C:\Windows Loaded Configuration File C:\Program Files (x86)\PHP\v5.3\php.ini Scan this dir for additional .ini files (none) Additional .ini files parsed (none) What am I messing up on, or is there a different way to go about this?

  Read the article

• Snapshotting single disk of running Hyper-V VM

  - by modelnine

  I'm currently somewhat at a loss of how to create a snapshot of a single virtual hard-disk of a running Hyper-V VM. Generally, creating a differential disk while a server is shut down is no problem (i.e., call the new-vhd cmdlet and pass a ParentPath, then update the VHD-binding of the respective VM-device), but while the host is running, all I can find is checkpointing the VM as a whole (which creates snapshots of all attached disks), and leaves the VM-state in a form which isn't easily processable by external tools (i.e., it requires reading additional meta-data from the VM). Generally, what'd I'd like to happen for a single-disk snapshot (in my understanding) is: Pause the VM Rename current disk to some other name which specifies it as a base-snapshot Create a new VHD which has the renamed VHD as parent path and is marked as "current" Swap the VHD for the VM for the snapshotted hard-disk to the newly created differential VHD Resume the VM Is there any means to do this programatically? Update: I've seen that this is actually possible with SCSI-disks, i.e. pause the VM, remove the SCSI disk, make the snapshot, reattach the SCSI disk at the same position, resume the VM. And, the VM resumes properly. But: is something similar also possible with G1 machines for the boot disk which is always IDE?

  Read the article

• Changing the current URL but serving content from another (same domain) - ProxyPass?

  - by zigojacko

  I've been banging my head against the wall with this for months now so I hope someone on here will be able to finally advise what is needed for this. I have some URL's like this:- domain.com/category/subcat/filter/brand And I wish to rewrite the URL's to:- domain.com/category/brand-subcat Content loads fine at the first URL, I just want to show it at a different URL - is URL masking the correct term for this? I have a RewriteRule in .htaccess that should do this job as far as I believe:- RewriteRule ^([a-zA-Z]+)/([a-zA-Z]+)/filter/([a-zA-Z]+)$ $1/$3-$2 This isn't actually modifying the URL at all though on a Magento website (mod_rewrite is enabled and plenty of other rewrites are working from the same .htaccess). So firstly, I want to know is what I am trying to achieve definitely possible? If so, what is this process even called? Secondly, does this need to be handled using ProxyPass and then use a [P] flag with the rewrite rule? I assume the Apache server doesn't have mod_proxy enabled currently because when I add a [P] flag, the URL returns a 403 forbidden error with the full server path for the current URL. Please could anyone kindly advise what on earth I need to do to achieve this?

  Read the article

• Multiple rack apps on nginx + passenger, one as root, the other not...config help

  - by cannikin

  So I've got two apps I want to run on a server. One app I would like to be the "default" app--that is, all URLs should be sent this app by default, except for a certain path, lets call it /foo: http://mydomain.com/ -> app1 http://mydomain.com/apples -> app1 http://mydomain.com/foo -> app2 My two rack apps are installed like so: /var /www /apps /app1 app.rb config.ru /public /app2 app.rb config.ru /public app1 -> apps/app1/public app2 -> apps/app2/public (app1 and app2 are symlinks to their respective apps' public directories). This is the Passenger setup for sub URIs described here: http://www.modrails.com/documentation/Users%20guide%20Nginx.html#deploying_rack_to_sub_uri With the following config I've got /foo going to app2: server { listen 80; server_name mydomain.com; root /var/www; passenger_enabled on; passenger_base_uri /app1; passenger_base_uri /app2; location /foo { rewrite ^.*$ /app2 last; } } Now, how do I get app1 to pick up everything else? I've tried the following (placed after the location /foo directive), but I get a 500 with an infinite internal redirect in error.log: location / { rewrite ^(.*)$ /app1$1 last; } I hoped that the last directive would prevent that infinite redirect, but I guess not. /foo gets the same error. Any ideas? Thanks!

  Read the article

• WNDR3700 Router + Cisco SG200-08 + LACP + Dual Uplink

  - by kobaltz

  Background I have a storage server that has several virtual machine images stored on them. I would store them locally, but I have limited space on my desktop (using SSD storage). I would like to increase the bandwidth between the desktop and the storage server by using two NICs on each computer. My original configuration allowed about 55MBps between the desktop and storage server. This storage server also has several TBs of documents, pictures, movies, vms, and ISO/programs. The storage server has 8 1.5TB hard drives in a RAID 10 configuration with a hardware RAID controller. The benchmarks on the RAID 10 are about 300MBps. Configuration In short, I am trying to bridge my switch and router. The switch is a small 8 port Cisco smart switch that supports 802.3ad LACP. I have two computers plugged into the switch, each with 2 Intel Gigabit NICs. The first computer is a Windows 7 machine that has the Intel ANS software installed. I have LACP configured with the computer and now show 3 NICs (2 Physical + 1 TEAM Virtual @ 2Gbps). It looks like this computer is configured correctly. I trunked the two ports that this computer is plugged into with the switch's web interface. The second computer is a homebrew storage box running debian. I also have the bonding enabled on this machine and the switch configured with LACP. Without having the WNDR3700 router in the picture yet, I am able to communicate between the Windows 7 machine and the debian box since they both have static IP addresses. With LACP enabled on both machines I am getting about 106-108MBps speeds. Issue I plug in a network cable from the switch into the router and enable DHCP on the desktop. I saw no need to have a static address on the desktop. My transfer rates are still from 106MBps-108MBps. While this is still a boost, I am trying to figure out how to get about 140-180MBps. I am thinking that I need to increase the bandwidth from the router to the switch. My switch allows 4 groups for port trunking. I plugged in a second network cable from the router to the switch. My question is, what is the proper way to fix this issue. Should I port trunk the two ports that are going from the switch to the router? Keep in mind that the router is a WNDR3700 and is unsure whether or not it supports LACP. I do have OpenWRT installed on the router, but it still wasn't clear in any documentation that I found if it supported 802.3ad LACP standards. I am also wondering if there needs to be anything changed within the Cisco settings. [Edit] - Corrected some numbers, wasn't really paying attention. It looks like the speeds though at least two NICs are bonded with LACP is still reaching the max bandwidth of one port. Is there a way to configure the switch so that I can increase this bandwidth? Also, on the storage server, I had a couple of extra NICs laying around and threw them on there as well. Another EDIT and More Findings I happened to look at the traffic of each individual NIC and think that I see the problem. I tested with a simple transfer for a 4GB file. I noticed that only one of the NICs was taking the load of the traffic. I then copied the file back to the Storage Server and noticed that the other NIC was sending out the traffic. I have 802.3ad LACP enabled on the two NICs and I see that it gets enabled dynamically on the switch's interface. Should I be using Static Link Aggregation?

  Read the article

• How to change mount to grant user write permissions?

  - by nals

  I am on TomatoUSB, and using the feature to have a NAS. The only way I can write to the Samba share is if I force root: [global] interfaces = 127.0.0.1, 192.168.1.1/24 bind interfaces only = no workgroup = WORKGROUP netbios name = TOMATO security = share wins support = yes name resolve order = wins lmhosts hosts bcast guest account = nobody [Public] path = /mnt/sda2 read only = no public = yes only guest = yes guest ok = yes browseable = yes comment = Network share force user = root writeable = yes I dont really like the idea having to use root to allow write access to my share. I have a samba account created already named nobody to allow access to the share. However every time I try to write I get access denied error. fstab: /dev/sda2 /mnt/sda2 vfat defaults 0 0 Further more every time I try to chmod 777 /tmp/mnt/sda2 the permissions are not changed, and no error is produced. They stay 755. drwxr-xr-x 2 root root 4096 Jun 4 01:49 sda2 Basically; how can I give the user nobody write permissions to my mount? dev name: /dev/sda2 dev mount: /tmp/mnt/sda2

  Read the article

• Windows 7 access denied to executables.. by what?

  - by stijn

  Ever since I started using Windows 7 this problem has been bothering me. From time to time I see similar questions popping up on misc forums, but never did I see an answer. Here are two scenarios that nearly always reproduce it: the explorer way with explorer, navigate to a directory containing at least one exe file go one directory up immediately delete the directory just navigated to yields Folder Acces Denied dialog stating You need permission to perform this action You require permission from Administrators to make changes to this folder, with the buttons try Again and Cancel hitting Try Again never works immediately. Waiting a minute or so and then clickig it again does work note: if in step 2 and waiting a minute or more before going up one directory, the problem does not occur and the folder can be deleted the visual studio way build a project producing an exe file run the executable then close it immediately build the project again (by changing a single character in a source file for example) yields fatal error LNK1168: cannot open /path/to/the.exe for writing note: if in step 2 and waiting a minute or more before building again, the problem does not occur some specs happens both on Windows 7 32 and 64 bit, with VS2008/2010/2011 happens on 3 different machines I do not have a virusscanner of any kind I do have a bunch of services disabled, but nothing that prevents Windows from running normally, UAC is disabled as well happens on any type of disc I always use a user account that is in the Administrators group Obviously both scenarios are very similar and extremely reproducable. So I figured some process must have the file open for some reason, and release it again later. However, using systinternal's handle -a the exe file in question never shows up. (that is the correct way to use handle, right?) So while explorer/VS are reporting they cannot access the file, handle.exe says it's not in use anywhere. This leaves me rather clueless, so I'm wondering if someone can come up with a solution: why does this happen, and how to solve it?

  Read the article

• Windows 2008 R2 file share - any way to "lock it down" outside of a 3rd party app?

  - by TheCleaner

  I have a 3rd party app that "makes a call" to write files to a file share on our network using the currently logged in credentials of the Windows domain user. Meaning the 3rd party app doesn't pass the apps credentials but simply issues a behind the scenes copy command to take a source file specified and copy/move it to the destination "repository" on the file share. The basic premise is that it keeps revisions/approvals for Document Control (think svn/git I guess, similar to this question: Lock down Windows folder to only be updatable by SVN). This all works fine...but here's my issue: I need a way to lock down the file share from being accessed/modified outside of using the 3rd party app (meaning prevent explorer/word/excel/etc from getting to that share). I know I can do the following: make the share a hidden share ($) - this definitely helps. Most users would have zero clue on how to get to such a share. Solves probably 95% of my issue. go one step further and set the "Hidden" attribute on the folders in the hidden share - this would go a little further in that even if a user knows the path to the hidden share like \\server\hidden$ they still won't see folders in that share without changing their explorer options to "show hidden files/folder Any other ideas on how I can lock this down? The users still need modify rights to this share/folders since the 3rd party app relies on their Windows permissions to that location when copying the files into it. I can't really use 3rd party tools to password protect the folder/share without causing the 3rd party app functions to fail.

  Read the article

• Windows Explorer and UAC: run elevated

  - by syneticon-dj

  I am profoundly annoyed by UAC and switch it off for my admin user wherever I can. Yet, there are situations where I can't - especially if those are machines not under my continuous administration. In this case, I am always challenged with the task of traversing directories using my administrative user via the Windows Explorer where regular users do not have "read" permissions. The possible two approaches to this problem so far: change the ACLs to the directory in question to include my user (Windows conveniently offers the Continue button in the "You don't currently have permissions to access this folder" dialog. This obviously sucks since more often than not I do not want to change ACLs but just look into the folder's contents use an elevated cmd.exe prompt along with a bunch of command line utilities - this usually takes a lot of time when browsing through large and / or complex directory structures What I would love to see would be a way to run Windows Explorer in elevated mode. I have yet to find out how to do so. But other suggestions solving this problem in an unobtrusive way without changing the entire system's configuration (and preferably without the need for downloading / installing anything) are very welcome, too. I have seen this post with a suggestion for altering HKCR - interesting, but it changes the behavior for all users, which I am not allowed to do in most situations. Also, some folks have suggested using UNC paths to access the folders - unfortunately this does not work when accessing the same machine (i.e. \\localhost\c$\path) as the "Administrators" group membership is still stripped from the token and a re-authentication (and thus the creation of a new token) would not happen when accessing localhost.

  Read the article

• Migrating WebLogic 10.3.0 to new host. Slow managed server startup times

  - by wadevondoom

  We are migrating our Blue Martini Commerce application (only supported on WebLogic 10.3.0) to a new host (Redhat 6.3 on a VMWare ESX vm). We are seeing extremely slow start up times for our managed server(s) that is basically 20x slower than our current production. As a for instance the Publish managed server takes ~30 - 45 seconds in current production and in the new environment it takes ~10 minutes. The setup uses the same domain structure and JVM as the current production environment. The same setup files are used. We use jdk1.6.0_33 on 64 bit architecture. We used the generic 64bit weblogic installer and used pack / unpack utilities to migrate the domain. The JAVA_OPTS to start this server are: "-d64 -Xms256m -Xmx512m -XX:PermSize=48m -XX:MaxPermSize=256m" The sysadmins have checked /etc/sysctl.conf and /etc/limits.conf to ensure we were not hitting some kind of process limit. As I am not sure what this managed server does from a Blue Martini perspective during the phase of startup I also had the DBA check to ensure that Oracle RAC (11.2.0.3) wasn't also hitting some kind of process limit or if there was a tns listener issue. The new host is quite a bit stricter with their server lock downs so there are a few differences.... Redhat 6.3 in new env, RH 5.7 in current SElinux is targeted in new env and disabled in current VM in new env and dedicated hardware in current iptables disabled in current. It was enabled in new prod but I had them disable it just in case I apologize for not being more specific. I am mostly hoping got some tips. I do not have the typical root access I would normally have in this environment. I am just hoping got a path forward. I did a few 'kill -3' to see if there are blocked threads and I got nadda. The service works for all intents and purposes it is just painfully slow. Thanks you all in advance for reading and best regards. Wade

  Read the article

• Why are my Windows 7 updates continuously failing?

  - by Chris C.

  I'm an advanced level user here with an odd issue. I have two Windows Updates that are failing to install, every single time. I'm getting a mysterious "Code 1" error on both updates, an error for which I'm having difficulty finding a solution. The updates in question are: Security Update for Microsoft Visual C++ 2008 Service Pack 1 Redistributable Package (KB2538243) System Update Readiness Tool for Windows 7 for x64-based Systems (KB947821) [May 2011] Because these updates are failing, the Shut Down button in my start menu always has the shield icon next to it, indicating that "new" updates will be installed on shut down. But, of course, they'll fail and when the PC is restarted, the shield icon is still there. When checking the update history and viewing the details of the failed updates, I get the following: Security Update for Microsoft Visual C++ 2008 Service Pack 1 Redistributable Package (KB2538243) Installation date: ?6/?29/?2011 3:00 AM Installation status: Failed Error details: Code 1 Update type: Important A security issue has been identified leading to MFC application vulnerability in DLL planting due to MFC not specifying the full path to system/localization DLLs. You can protect your computer by installing this update from Microsoft. After you install this item, you may have to restart your computer. More information: http://go.microsoft.com/fwlink/?LinkId=216803 and: System Update Readiness Tool for Windows 7 for x64-based Systems (KB947821) [May 2011] Installation date: ?6/?28/?2011 3:00 AM Installation status: Failed Error details: Code 1 Update type: Important This tool is being offered because an inconsistency was found in the Windows servicing store which may prevent the successful installation of future updates, service packs, and software. This tool checks your computer for such inconsistencies and tries to resolve issues if found. More information: http://support.microsoft.com/kb/947821 About My System I'm running Windows 7 Home Premium 64-bit. This is a custom PC build and the OS was installed fresh, not an upgrade from a previous version. I've been running this system for about four months. Windows Updates aside, the system is usually quite stable.

  Read the article

• Process PHP files from a network share in a vmware virtual machine

  - by nhinkle

  As a testing environment, I have set up a vmware virtual machine running Windows Server 2008 R2. I have Apache and PHP installed (as part of the xampp package). I am doing the development outside of the VM, and so want Apache to serve PHP files from a VM shared folder (which appears as a network share in the VM). I have done this by creating an NTFS symbolic link in Apache's htdocs directory. I can access this directory from the browser, and plain-text files are readable. However, PHP fails to process files, instead returning the following error: Warning: Unknown: failed to open stream: No such file or directory in Unknown on line 0 Fatal error: Unknown: Failed opening required 'C:/xampplite/htdocs/path/to/file.php' (include_path='.;C:\xampplite\php\PEAR') in Unknown on line 0 It appears to be a permissions issue — PHP doesn't seem to be allowed to read the file to process it. However, Apache has no problem opening files in the directory. I cannot figure out how to give PHP the necessary permissions to process the file. Does anybody know of a way to make this work, or else another solution for getting the files into the VM automatically while I develop on the host machine?

  Read the article

• apache virtualhost: Auto subdomain with exception

  - by Ineentho

  I've been searching for a way to automatically redirect domains to a specific folder, and fond a good answer here on serverfault: Apache2 VirtualHost auto subdomain. (The accepted answer) So far everything works good, however now I need to add an exception to this. The result I want is this: http://localhost/ --> E:/websites/ http://specialDomain2/ --> E:/websites/ http://normal1.com/ --> E:/websites/normal1.com/ http://normalDomain.com/ --> E:/websites/normal2.com/ I get the expceted result for the two last domains, but the localhost doesn't work. I copied the script from the question aboved, and tried to add something like <VirtualHost *:80> RewriteEngine On RewriteMap lowercase int:tolower # if already rewitten and we have the right path, stop right here RewriteRule ^(E:/websites/[^/]+/.*)$ $1 [L] RewriteRule ^localhost/(.*)$ E:/websites/$1 [L] # <-- Added this row RewriteRule ^(.+) ${lowercase:%{SERVER_NAME}}$1 [C] RewriteRule ^(www\.)?([^/]+)/(.*)$ E:/websites/$2/$3 [L,E=VHOST_ROOT:E:/websites/$2/] </VirtualHost> I thought this would make sense, since I would translate this to if URL = localhost/* Do nothing (because of the [L] flag), and use the default document root specified earlier else continue What's wrong with this? Thanks for any help!

  Read the article

• Install Exchange 2013 with DSC

  - by Alain Laventure

  I tried to install Exchange 2013 with the resource windowsProcess in existing Exchange Configuration. All prerequisites are installed (the Exchange Organization still exists). This is my Resource section: WindowsProcess Exchange2013 { Credential=$credential Path= "C:\Sources\Cumulative Update 5 for Exchange Server 2013 (KB2936880)\Setup.exe" Arguments= "/mode:Install /role:Mailbox /IAcceptExchangeServerLicenseTerms /TargetDir:C:\EX2013" Ensure= "Present" } #End Filter } #End Node } # End configuration /* @TargetNode='TargetDSC02' @GeneratedBy=exadmin @GenerationDate=08/02/2014 08:16:03 @GenerationHost=SOURCEDSC02 */ instance of MSFT_Credential as $MSFT_Credential1ref { Password = "Password1"; UserName = "S05\\Exadmin"; }; Exadmin is a member of Orgaganization Management Group and it is also member of Domain Admin Group, to be able to install Exchange When I execute this resource , Exchange Installation Start but after 1 minute the installation stops with this error: Failed [Rule:GlobalServerInstall] [Message:You must be a member of the 'Organization Management' role group or a member of the 'Enterprise Admins' group to continue.] To be sure that the right is really the problem I create a special User with only Administrator right of the Exchange server and with no Exchange Permission I run manually on the new Exchange server .\Setup.exe /mode:Install /role:Mailbox /IAcceptExchangeServerLicenseTerms /Targetdir:C:\EX2013 And I got the Same error that with DSC. After I add my test user in the Organization Management Group and I run again manually .\Setup.exe /mode:Install /role:Mailbox /IAcceptExchangeServerLicenseTerms /Targetdir:C:\EX2013 And the Exchange 2013 installation finish without any error. That prove that the problem with DSC is Permission right.

  Read the article

• Postfix : outgoing mail in TLS for a specific domain

  - by vercetty92

  I am trying to configure postfix to send mail in TLS (starttls in fact), but only for a specific destination. I tried with "smtp_tls_policy_maps". This is the only line in my main.cf file regarding TLS configuration, but it seems not working. Here is my main.cf file: queue_directory = /opt/csw/var/spool/postfix command_directory = /opt/csw/sbin daemon_directory = /opt/csw/libexec/postfix html_directory = /opt/csw/share/doc/postfix/html manpage_directory = /opt/csw/share/man sample_directory = /opt/csw/share/doc/postfix/samples readme_directory = /opt/csw/share/doc/postfix/README_FILES mail_spool_directory = /var/spool/mail sendmail_path = /opt/csw/sbin/sendmail newaliases_path = /opt/csw/bin/newaliases mailq_path = /opt/csw/bin/mailq mail_owner = postfix setgid_group = postdrop mydomain = ullink.net myorigin = $myhostname mydestination = $myhostname, localhost.$mydomain, localhost masquerade_domains = vercetty92.net alias_maps = dbm:/etc/opt/csw/postfix/aliases alias_database = dbm:/etc/opt/csw/postfix/aliases transport_maps = dbm:/etc/opt/csw/postfix/transport smtp_tls_policy_maps = dbm:/etc/opt/csw/postfix/tls_policy inet_interfaces = all unknown_local_recipient_reject_code = 550 relayhost = smtpd_banner = $myhostname ESMTP $mail_name debug_peer_level = 2 debugger_command = PATH=/bin:/usr/bin:/usr/local/bin:/usr/X11R6/bin xxgdb $daemon_directory/$process_name $process_id & sleep 5 And here is my "tls_policy" file: gmail.com encrypt protocols=SSLv3:TLSv1 ciphers=high I also tried gmail.com encrypt My wish is to use TLS only for the gmail domain. With this configuration, I don't see any TLS line in the source of the mail. But if I tell postfix to use TLS if possible for all destination with this line, it works: smtp_tls_security_level = may Beause I can see this line in the source of my mail: (version=TLSv1/SSLv3 cipher=OTHER); But I don't want to try to use TLS for the others domains...only for gmail... Do I miss something in my conf? (I also try whith "hash:/etc/opt/csw/postfix/tls_policy", and it's the same) Thanks a lot in advance

  Read the article

• Reading email from Emacs VM using a secure server (Gmail)

  - by Alan Wehmann

  This is a question (see below) originally entered at https://answers.launchpad.net/vm/+question/108267 and upon the recommendation of Uday Reddy the question and answers are being moved here. The date of the original question was May 4, 2010. One subject of the question is use of the program stunnel with program View Mail (run within Emacs) on a PC running Microsoft Windows, in order to read email from a server that requires use of TSL/SSL (Gmail). See the related question, How to configure Emacs smtp for secure server for using a secure server, for sending email. The programs discussed are Emacs, VM (ViewMail) and stunnel. The platform under discussion is MS Windows. The original question was asked by usr345 on 2010-04-24: I tried to install vm on Windows, but when I tried to get the mail from gmail using ssl, an error emerges, emacs hanges-up. Here is the code from .emacs: (add-to-list 'load-path (expand-file-name "~/vm/lisp")) (add-to-list 'Info-default-directory-list (expand-file-name "~/vm/info")) (require 'vm-autoloads) (setq vm-primary-inbox "~/mail/inbox.mbox") (setq vm-crash-box "~/mail/inbox.crash.mbox") (setq vm-spool-files `((,vm-primary-inbox "pop-ssl:pop.gmail.com:995:pass:usr345:PASSWORD" ,vm-crash-box))) (setq vm-stunnel-program "g:/program files/stunnel/stunnel.exe") So, the question: How to configure pop-ssl on Windows?

  Read the article

< Previous Page | 629 630 631 632 633 634 635 636 637 638 639 640  | Next Page >