Search Results

Search found 22900 results on 916 pages for 'pascal case'.

Page 634/916 | < Previous Page | 630 631 632 633 634 635 636 637 638 639 640 641  | Next Page >

• Inter-vlan routing issues

  - by DKNUCKLES

  I've been brought in to help administer a network and I've run into an issue - I'm not sure why this one is beyond me, however I figure an extra set of eyes on the problem may help resolve the issue. I have an HP MSM720 controller and at the time I'm trying to set up a basic hotspot set up with access points. For the time being I'm just looking to have people authenticate with a PSK and access the internet and other resources (namely printers) on other vlans. The user authenticates and the DHCP server on the controller gives them a 192.168.1.0/24 address. They are able to successfully browse the internet and ping machines on other networks, however they are unable to print to network printers that sit on the same LANs as the very computers that wireless clients can ping. The (extremely simplified) topology is as follows Computers on the wireless 192.168.1.1 network are able to ping computers on the 192.168.0.0 network, however cannot ping or print to the printers on the same network. I'm baffled and I have no idea why this is the case. Can anyone shed some light on this for me? Can someone spot the error of my configuration? EDIT : It should be noted that for whatever reason other computers on the 10.0.100.0/24 network cannot even ping the gateway of the Wireless Access network (192.168.1.1) - I'm not sure if this is relevant. These are the VLANS listed on the controller.

  Read the article

• Raid-1 Western Digital Green AARS, cloning and WD Align Utility

  - by Jaguar

  Hello all, My current setup runs on top of 2x Western Digital 2500KS drives on Raid-1, using the motherboard's 780G raid controller, on WinXP. Everything is fine, but the drives are a bit noisy. I am considering buying 2x WD6400AARS disks which are the 640GB slower 'green' drives, but also feature the Advanced Formatting 4KB sectors. This means that for WinXP the partition will have to be aligned to work properly, else there is a performance penalty. There are 2 questions here: The Green drives from WD are all slower and are (according to WD) susceptible to drop-out's from the controller. Has anyone any experience in this matter? Is there a possibility the controller will drop a drive? If so, can i do anything about it? Secondly, western digital gives a utility to perform the alignment on the partition. The thing is, will the utility see the drives in question as the operating system only sees 1 logical disk? I will be making the transition using a cloning tool (most probably norton ghost) unless i don't find a solution or a clear answer, in which case i'll just buy a win 7 license and make a clean install... thx in advance

  Read the article

• Htpc aka "Media Center": cheap and *silent*?

  - by Unknown

  It may be me, or the place I live (Italy), but it seems pretty hard to get a build or a prebuilt nettop or a laptop that fits the need. I need something silent able to playback all h.264 fullhd content without stuttering, and well (and not loosing the hw acceleration because of softsubs...) silent not ugly silent and (possibly) cheap. I'm going the linux route, therefore i'm moving towards a cpu-based or nvida-integrated solution (i don't think ati hw accelerated playback - or the intel "hd" acceleration - is useable yet). Ion nettop; it's either the Acer Revo (but here it's incredibly pricey and it's hard to find the dualcore version) or the Asrock Ion 330, that in the current version is rated "silent" at 26Db. 26. Sounds pretty noisy to me!!! the previous version was even worse. was this product really aimed at htpc market?? the Dell Zino - i think it's ATI based unfortunately. Laptop: correct me if I'm wrong: sub 600€/$ units are quite loud under full load (because of the tiny fans). ULW laptops are indeed quite similar: tiniest fans = high pitched noise and the cpu still lacks power for non hd-accelerated video decoding Handmade build: little money can be saved with underpowered cpus, a low-midrange cpu would help in the case of non-hw-accelerated content the cases are quite pricey the PSU one has to get ranges between 100/150 €/$ minimum to keep the noise down a low-mid build, all included, sums up to over 650 €/$ for a still-looking-ugly-unit, without the blu-ray drive. Please help. What do you advise on this? ;) Am I ignoring laptops too much, maybe? Are low-priced Acers that noisy/high pitched under full load?

  Read the article

• How \Deleted flag can be unset for all mails in cyrus-imapd mailbox?

  - by Sachin Divekar

  I have a 5GB mailbox which I moved using imapsync. But somehow I messed up with --delete/--delete2 option and end up with almost all the messages having \Deleted flag set. I do not have delayed expunge enabled, so I can not use unexpunge utility. I am using cyrus-imapd v2.3.7. Using cyrus-imapd's debugging feature I found out that email client(Roundcube in my case) fires following IMAP command to unset it. UID STORE 179 -FLAGS.SILENT (\Deleted) I don't know if somehow I can fire this command for all the mails. Is there any way I can unset \Deleted flag for all the mails in the mailbox? UPDATE: Using @geekosaur's tip of specifying range of message-ids in the above command, I could solve it for one mailbox under INBOX like INBOX.folder1. Is there any way I can do it for multiple mailboxes under INBOX recursively? Now I am working on solving it using/creating some script, maybe using Perl's IMAP related module. But still I need to solve it asap so inputs are welcome.

  Read the article

• Fedora-13 not detecting USB HDD enclosure (with HDD)

  - by Ramy

  I recently purchased this enclosure: http://www.amazon.com/Inland-2-5-Inc.../dp/B003SZ2Y12 and this HDD: http://www.amazon.com/Seagate-Barrac...3811667&sr=8-1 Now, I let my brother in law use the enclosure with his 160GB disk to back some stuff up. He then gave me that disk in my enclosure and I backed up my computer and my fiances computer. So...obviously, i had no problem mounting that disk. I plan on keeping this disk as my "natural disaster backup" (in case my apartment building burns down, i still have that disk with my stuff backed up). I want to use the 1.5T disk as my regular/more frequent backup device, but it doesn't seem to be mounting to my F-13 machine. I searched through this forum and found someone advising to run the following: # mount -t vfat /dev/sda1 /mnt this is the output i get when I run that: mount: /dev/sda1 already mounted or /mnt busy mount: according to mtab, /dev/sda1 is mounted on /boot Thing is, shouldn't this disk automatically mount just like the LAST disk in the same enclosure with the same USB cable and power supply? Any help would be greatly appreciated. THANKS!

  Read the article

• D-LINK 2450U DSL router: Port forwarding forwading to the modem itself, not the specified IP

  - by axk

  I found a similar question but it has no satisfactory answers. I have a D-LINK 2540U DSL router. It has a basic port forwarding(under DNS - Virtual Servers) configuration in the administration panel where you specify: external port range, protocol, internal port range, server IP address and it is supposed to forward that port to that IP address. When I first set it up for a Real VNC connection it worked fine, just as I expected. Then I added a DynDNS configuration entry in the router's 'Dynamic DNS' section and added an additional SSH (22) forwarding rule. The SSH forwarding also worked fine (now with the dynamic hostname, but I suppose it doesn't make any difference as far as SSH is concerned). Then I removed the SSH rule and after that the VNC forwarding stopped working with the VNC client failing to connect (I have tried to connect with telnet and it also failed to connect, so it wasn't a VNC problem). After adding a rule for port 80 it turned out it would forward on port 80 though not to the specified server IP but to the modem itself. At least it is what it looks like, because it gives me the administration panel when I connect to my external IP (both using a browser and plain telnet in which case I can see that it is mini_hhtpd sitting on the port, which is obviously the modem's administration panel). Have anybody encountered a similar problem with port forwarding? I have tried to do a reset through the administration panel and to restore a backup of the settings made before I started playing with port forwarding, but it didn't help. Should I do a 'hard' reset with the button on the modem? Is it any different from the administration panel's reset (Restore default)?

  Read the article

• Bash Script - Traffic Shaping

  - by Craig-Aaron

  hey all, I was wondering if you could have a look at my script and help me add a few things to it, How do I get it to find how many active ethernet ports I have? and how do I filter more than 1 ethernet port How I get this to do a range of IP address? Once I have a few ethenet ports I need to add traffic control to each one #!/bin/bash # Name of the traffic control command. TC=/sbin/tc # The network interface we're planning on limiting bandwidth. IF=eth0 # Network card interface # Download limit (in mega bits) DNLD=10mbit # DOWNLOAD Limit # Upload limit (in mega bits) UPLD=1mbit # UPLOAD Limit # IP address range of the machine we are controlling IP=192.168.0.1 # Host IP # Filter options for limiting the intended interface. U32="$TC filter add dev $IF protocol ip parent 1:0 prio 1 u32" start() { # Hierarchical Token Bucket (HTB) to shape bandwidth $TC qdisc add dev $IF root handle 1: htb default 30 #Creates the root schedlar $TC class add dev $IF parent 1: classid 1:1 htb rate $DNLD #Creates a child schedlar to shape download $TC class add dev $IF parent 1: classid 1:2 htb rate $UPLD #Creates a child schedlar to shape upload $U32 match ip dst $IP/24 flowid 1:1 #Filter to match the interface, limit download speed $U32 match ip src $IP/24 flowid 1:2 #Filter to match the interface, limit upload speed } stop() { # Stop the bandwidth shaping. $TC qdisc del dev $IF root } restart() { # Self-explanatory. stop sleep 1 start } show() { # Display status of traffic control status. $TC -s qdisc ls dev $IF } case "$1" in start) echo -n "Starting bandwidth shaping: " start echo "done" ;; stop) echo -n "Stopping bandwidth shaping: " stop echo "done" ;; restart) echo -n "Restarting bandwidth shaping: " restart echo "done" ;; show) echo "Bandwidth shaping status for $IF:" show echo "" ;; *) pwd=$(pwd) echo "Usage: tc.bash {start|stop|restart|show}" ;; esac exit 0 thanks

  Read the article

• Run script before shutdown/restart

  - by dtbarne

  I'd like to run a PHP script when an instance is told to shutdown, but of course before it actually finishes shutting down. My particular script is just looking to push some log files from the local partition to a another server. I've got the gist of how this process works, but I need some clarification. How I understand it. Please correct me if I'm wrong. Create an executable script in /etc/init.d (lets call it /etc/init.d/push-logs) Create a symlink to /etc/init.d/push-logs from /etc/rc0.d (shutdown) and /etc/rc6.d (reboot). The name should be KXXpush-logs Here's my questions: Of course - am I understanding correctly? For #2 above - it sounds like the lower the XX the better - is there too low a number I can use? Does it matter if it shares a number with another script? Does the script in /etc/init.d/push-logs HAVE to follow the standard init.d template (supporting start/stop, etc. commands)? This doesn't really apply to my use case. If possible I just want the script to be the following: #!/bin/sh # # Run PHP file prior to shutdown # /usr/bin/php /path/to/php_file.php

  Read the article

• Are these computer parts compatible?

  - by Jcubed

  so I'm building a computer and i want to know if all these parts are compatible. case: http://www.amazon.com/Xion-Gaming-Steel-Tower-Computer/dp/B002139YSS/ref=sr_1_1?ie=UTF8&s=electronics&qid=1270923001&sr=8-1 power supply: http://www.amazon.com/Thermaltake-W0121RU-PurePower-Version-PCI-Express/dp/B0015MCMRG/ref=sr_1_1?ie=UTF8&s=electronics&qid=1270924656&sr=1-1 motherboard: http://www.amazon.com/GIGABYTE-GA-EP45-UD3P-LGA-Intel-Motherboard/dp/tech-data/B001HH2WE2/ref=de_a_smtd processor: http://www.amazon.com/Intel-Processor-1333MHz-LGA775-BX80570E8400/dp/B00116SLYY/ref=sr_1_1?ie=UTF8&s=electronics&qid=1270924524&sr=1-1 hard drive: http://www.amazon.com/Western-Digital-Caviar-Black-WD1001FALS/dp/B001C271MA/ref=sr_1_1?ie=UTF8&s=electronics&qid=1270924586&sr=8-1 DVD/Blu Ray Dive: http://www.amazon.com/LITE-Blu-ray-Internal-Optical-iHOS104/dp/tech-data/B002EE996Q/ref=de_a_smtd Graphics Card: http://www.amazon.com/Sapphire-Radeon-100252HDMI-PCI-Express-Graphics/dp/B001SJLLTQ/ref=sr_1_1?ie=UTF8&s=electronics&qid=1270924798&sr=1-1-spell Sound Card: http://www.amazon.com/Creative-Labs-SB0570L4-Blaster-Audigy/dp/B000LP0R3E/ref=sr_1_1?ie=UTF8&s=electronics&qid=1270924850&sr=1-1 Memory: http://www.amazon.com/Corsair-TWIN2X4096-8500C5DF-Dominator-PC2-8500-1066MHz/dp/B0014Z0Q04/ref=sr_1_1?ie=UTF8&s=electronics&qid=1270924896&sr=1-1-spell OS: Ubuntu 64-bit

  Read the article

• PXE booting LACP hosts on Force10 S50N with FTOS

  - by lolwutreddit

  Hardware: S50N Firmware: FTOS 8.4.2.6 Problem: We're trying to PXE boot some servers that are connected via port-channel interfaces with LACP. Current Work-around: we PXE boot a server with a single interface (eth0), and then use a Perl script to turn up the port-channel interfaces after the server is built. Details: Is anyone doing anything similar on Force10 S50 switches with FTOS? If not, is anyone doing this on another S series, or larger chassis-based Force10? I'm wondering if Native VLAN will solve this, since ports in a port-channel cannot explicitly have a VLAN set, and they don't seem to use the tagged or untagged VLAN that the port channel is in. I will confirm this next (I think it's the only thing I haven't tried) Juniper Example: http://broken.net/openindiana/how-to-pxe-boot-systems-on-lacp-using-juniper-switches/ Cisco: there are plenty of documented ways to solve this issue on IOS and Nexus Update/Edit: since there seems to be no way to use interface or port-channel mode commands to get the individual interfaces to show up in spanning-tree (rtsp in this case), the ports should never go into a forwarding state. I'm not going to mess with it anymore unless a) someone that has experience passes it on, or b) Force10 comes up with a solution for this (I'm guessing it will only be introduced on other S platforms (S55, S60), since the S50 seems to be near EOL). I'm basing that on the fact that the Open Automation type features are only being supported on the newer switches.

  Read the article

• external drive enclosure -> software RAID 5?

  - by memilanuk

  Hello all, I have two older PCs on my LAN posing as 'servers'... one running FreeNAS off a USB stick using three 500GB hdds in a ZFS RAID-Z pool serving as storage for the LAN and one running Debian Lenny with an 80GB drive used as a general purpose 'tinker' box that I can ssh into, etc. Problem is that the SMART report for one of those 500GB drives in the FreeNAS box is showing some pre-failure attributes, and the whole array is a little small anyways. Rather than simply replace one 500GB drive with another 500GB drive, and have no backup of the file server, I'd like to upgrade all the drives to 2TB ones - but I have no where to store that much data in the mean while. As such, I started looking at getting a 4-bay external drive enclosure with an eSATA card for the Debian box, with the hopes of creating a RAID5 + LVM setup using those drives and backing the data up to that external drive enclosure. After the backup is done, replace the drives in the FreeNAS box and rebuild the array there and mirror the data back. Then, I'd have both the primary storage (on the FreeNAS box) and a backup (which I don't have currently) using the external drive enclosure on the Debian box. My big question is... most of these external drive boxes seem to claim support for JBOD, RAID 0, 1, 10, 5, etc. - should I presume that is simply fake RAID like many commodity mobos have, and not really usable in Linux? In that case, with all the drives hanging off the one eSATA connection, will Linux (specifically Debian Squeeze, as I plan on upgrading that box here shortly) see all four drives, or just the first one? Will I be able to configure them in a RAID5 array as desired? Thanks, Monte

  Read the article

• tomcat 5.5 startup script on Ubuntu server

  - by Registered User

  Can any one share their Tomcat startup script I am looking for a tomcat start up script on a Ubuntu machine. My Ubuntu is 10.04 server. The tomcat is 5.5.30. It is in /opt/apache-tomcat-5.5.31 I tried a script #!/bin/bash # # tomcat # # chkconfig: # description: Start up the Tomcat servlet engine. # Source function library. . /lib/lsb/init-functions RETVAL=$? CATALINA_HOME="/opt/apache-tomcat-5.5.31" case "$1" in start) if [ -f $CATALINA_HOME/bin/startup.sh ]; then echo $"Starting Tomcat" /opt/apache-tomcat-5.5.31/bin/startup.sh fi ;; stop) if [ -f $CATALINA_HOME/bin/shutdown.sh ]; then echo $"Stopping Tomcat" /opt/apache-tomcat-5.5.31/bin/shutdown.sh fi ;; *) echo $"Usage: $0 {start|stop}" exit 1 ;; esac exit $RETVAL but it did not worked after a reboot. But the same script works if I do /etc/init.d/tomcat start or /etc/init.d/tomcat stop I have done update-rc.d tomcat defaults as it is a Ubuntu server but on reboot all of this fails to work.

  Read the article

• sql developer cannot establish connection to oracle db with listener running

  - by lostinthebits

  I am working from home and connected to my work's vpn. I have tried to connect to the work db with sql developer (the latest version and the previous version) on the following environments: mac os x 10.8.5 (with sql developer launched and installed directly on the iMac. sql developer launched and installed directly on a vm on same computer (guest Ubuntu 12.04 LTS) sql developer launched and installed directly on a vm on same computer (guest Windows 7.0 Professional) I get Status Failure Test Failed : IO Error - The Network Adapter could not establish the connection. I have read dba forums and googled and the most common suggestion is that the oracle listener is not up and running. I can conclusively say this is not the case because I have the option of using remote desktop and accessing the oracle db in question on my work computer. If the listener was down, according to my DBA, no one would be able to connect. My sysadmin and dba are stumped so I assume it is something unique to my home system. The reason I do not want to continue with the remote desktop workaround is because remote desktop has an annoying (infuriating often) lag.

  Read the article

• How does enterprise failover, such as with google.com, actually work?

  - by Alex Regan

  We have a few fedora systems that are configured for web, FTP, and email services. We'd like to mirror these services, so that we can provide near 100% reliability for our users. I'm a fairly experienced Linux administrator, but don't have much experience with redundant systems. What is the best way to do this? How does google and amazon do it? Google.com resolves to multiple IP addresses, but if my local desktop caches one of the IPs that are unreachable, I'm going to get a failed connection message. How do they prevent that from happening? If one of their servers goes down, how is it automatically redirected to another system, without the end-user ever knowing it? I understand there are failover devices, but they're only for failing over the system itself, not a complete network. Let's say we have the worst-case scenario, such as my primary system becomes inaccessible. What are the fundamental components that are used on Linux systems to provide this capability? I'm looking for concepts, or approaches, not answers like "check out openstack". What are the actual pieces that make up the solution? What has to be done to implement this capability? Hopefully my question is clear. I'd like to know what the pieces are that make up a failover system and what approach is taken by successful organizations that implement it. Thanks again, Alex

  Read the article

• Weird routing issue

  - by Joel Coel

  I'm having some weird internet problems on campus. I know it's something simple, but it's a case where I need another set of eyes. I think I can explain the problem best by posting a tracert: Tracing route to google.com [74.125.45.147] over a maximum of 30 hops: 1 3 ms 3 ms 3 ms 192.168.8.1 2 1 ms 1 ms 1 ms elissaemily-pc.york.edu [192.168.10.5] 3 2 ms 2 ms 2 ms rrcs-76-79-19-33.west.biz.rr.com [76.79.19.33] 4 31 ms 3 ms 2 ms ge-1-1-0.lnclne00-mx41.neb.rr.com [76.85.220.109] 5 20 ms 17 ms 17 ms ge-7-3-0.chcgill3-rtr1.kc.rr.com [76.85.220.137] 6 20 ms 20 ms 19 ms ae-5-0.cr0.chi30.tbone.rr.com [66.109.6.112] 7 19 ms 19 ms 24 ms ae-1-0.pr0.chi10.tbone.rr.com [66.109.6.155] 8 26 ms 24 ms 24 ms 74.125.48.109 9 23 ms 24 ms 21 ms 216.239.46.246 10 39 ms 39 ms 55 ms 209.85.242.215 11 39 ms 39 ms 39 ms 209.85.254.243 12 39 ms 40 ms 96 ms 209.85.253.145 13 39 ms 39 ms 39 ms yx-in-f147.1e100.net [74.125.45.147] Trace complete. Note the second entry in there. Not only is the host name a student's computer, but the ip address doesn't exist. Dhcp shows that host as having a different address and you can't ping any 192.168.10.5. Yet somehow it's routing packets for us (and not very well, either — things are slow right now). The basic network routing table looks like this: Destination Subnet Mask Gateway --------------------------------------- Default Route -- 10.1.1.5 (our firewall) 10.0.0.0 255.0.0.0 -- 192.168.8.0 255.255.252.0 --

  Read the article

• sudo ./starling start works well but sudo service starling start fails

  - by Keating Wang

  sudo ./starling start works well but sudo service starling start fails $ sudo ./starling start * Starting Starling Server... [ OK ] $ sudo ./starling stop * Stop Starling Server... [ OK ] $ sudo service starling stop * Starting Starling Server... /home/keating/.rvm/rubies/ruby-1.9.2-p290/lib/ruby/site_ruby/1.9.1/rubygems/dependency.rb:247:in `to_specs': Could not find starling (>= 0) amongst [minitest-1.6.0, rake-0.8.7, rdoc-2.5.8] (Gem::LoadError) from /home/keating/.rvm/rubies/ruby-1.9.2-p290/lib/ruby/site_ruby/1.9.1/rubygems/dependency.rb:256:in `to_spec' from /home/keating/.rvm/rubies/ruby-1.9.2-p290/lib/ruby/site_ruby/1.9.1/rubygems.rb:1229:in `gem' from /home/keating/.rvm/gems/ruby-1.9.2-p290/bin/starling:18:in `<main>' The error above is 'cannot find gem starling' Following the starling file(located in /etc/init.d, rwxrwxrwx): set -e LOGFILE=/var/log/starling/starling.log SPOOLDIR=/var/spool/starling PORT=22122 LISTEN=127.0.0.1 PIDFILE=/var/run/starling.pid NAME=starling DESC="Starling" INSTALL_DIR=/home/keating/.rvm/gems/ruby-1.9.2-p290/bin/ DAEMON=$INSTALL_DIR/$NAME SCRIPTNAME=/etc/init.d/$NAME OPTS="-d" . /lib/lsb/init-functions d_start() { log_begin_msg "Starting Starling Server..." start-stop-daemon --start --quiet --pidfile $PIDFILE --exec $DAEMON -- $OPTS || log_end_msg 1 log_end_msg 0 } d_stop() { log_begin_msg "Stopping Starling Server..." start-stop-daemon --stop --quiet --pidfile $PIDFILE || log_end_msg 1 log_end_msg 0 } case "$1" in start) d_start ;; stop) d_stop ;; restart|force-reload|reload) d_stop sleep 2 d_start ;; *) echo "Usage: $SCRIPTNAME {start|stop|restart|force-reload}" exit 3 ;; esac exit 0

  Read the article

• Finding a backup and synchronization solution

  - by Andrea Zilio

  I'm having difficulties to find a backup and synchronization solution with the following characteristics: Cross-platform: Windows, Linux, Mac Offsite backup (so Internet Backup) Data deduplication Transfer only new/modified bits of modified files Secure: Data encrypted before leaving computer Maintain multiple versions of files (even deleted files) Folder synchronization integrated with backup and across multiple computers connected to the internet (not necessarily in the same LAN) I think that the Folder Sync feature needs a better explanation. The use case is this: you have a desktop pc and a laptop. The desktop pc contains a folder with some files and this folder is part of the backup (so it was selected to be backed up). The laptop does not contain that folder or that files at all. Then you're abroad with your laptop and you need that folder. So you want to be able to open the backup program, select that folder from the backup and download it in your laptop mantaining it synchronized with the backed up version. When you then come back home and switch on your desktop pc you want the folder we're talking about to be updated in the desktop PC. Does anyone knows any service with all these features? I've only found SpiderOak to support all the features I've mentioned but I'm not completely satisfied by the time taken to complete a backup. Sometimes it seems to hang for minutes with no reasons at all and folder synchronization occurs only after all files are backed up (instead folder sync should have a separated queue independent from other backup operations and synchronization should occurs frequently... for example every 5 minutes or less, independently from the frequency of normal backup operations)

  Read the article

• Cant connect to MySQL server from Java application

  - by RN

  This is on VPS\Centos server. The MySQL server is pre configured. I am running the Java application on Tomcat My Java web application is not able to connect to the MySQL server. I get an error - "Caused by: java.net.ConnectException: Connection refused" I suspect this to be a configuration problem rather than a coding problem- hence I have posted this on ServerFault And yes, The same web-app is able to connect to MySQL on a different linux box This is the URL that I provided to my Java application (note- it assumes default port) url = "jdbc:mysql://localhost/pickupgames" My first suspicion was that I am running on a non-default port So I tried to find the port where mySQL server is running I tried every trick mentioned in http://serverfault.com/questions/116100/how-to-check-what-port-mysql-is-running-on But no luck ! SHOW GLOBAL VARIABLES LIKE 'PORT'; This shows port 0 netstat -tlnp doesn't show mysql at all /etc/my.cnf It has no port entry telnet localhost 3306 Doesn't connect And in case you are wondering if mysql server is running at all or not It is And I know for sure, because I have been able to login using the mysql command Also # ps -ef|grep 'mysql' root 31839 27662 0 00:49 pts/3 00:00:00 grep mysql root 32452 1 0 Apr02 ? 00:00:00 /bin/sh /usr/bin/mysqld_safe --skip-grant-tables --skip-networking mysql 32504 32452 0 Apr02 ? 00:00:06 /usr/libexec/mysqld --basedir=/usr --datadir=/var/lib/mysql --user=mysql --pid-file=/var/run/mysqld/mysqld.pid --skip-external-locking --socket=/var/lib/mysql/mysql.sock --skip-grant-tables --skip-networking Please note the --skip-networking parameter Does this have something to do with the issue ? Any explanation why I cant connect to mysql server on port 3306 by telnet? Or why it docent show up under netstat? Any suggestion on whet I should try next ?

  Read the article

• ASUS P8B WS - Endless Reboots

  - by tuxGurl

  I am running a Intel XEON 1245 with 4GBx2 Kingston Memory ECC Unbuffered DDR3 on an ASUS P8B WS motherboard. BIOS Version 0904 x64. This system is a little over a month old. It is running Ubuntu 11.10. This evening I found the machine turned off. When I tried to restart it, it would POST and stop at the GRUB screen. When I selected Ubuntu and hit enter within 2-3 seconds the would shutdown and restart. If I stayed at the GRUB screen and did nothing the system would not cut out. I tried booting off a USB stick and again 2-3 seconds after selecting 'Try Ubuntu without Installing' the machine will cut power and reboot. Things I have tried so far: Resetting the BIOS using the on board jumper Resetting the BIOS settings to default Disconnecting all external hardware - except keyboard & monitor Booting with 1 stick of RAM - I tried different single sticks Ensured that onboard EPU and GPU boost switches are in the off position. I am running a Memtest86 right now and it has been running for 38+ minutes. This is not an OS problem or an overheating issue (I have a CoolerMaster HAF Case with 3 fans besides the CPU fan) I am at a loss as to what to try next. I think the BIOS is mis-configured somehow but I don't know what to look for.

  Read the article

• How to Move SMS from iPhone to Mac?

  - by seda16

  SMS is the main form to Communicate with others, you would saved many messages on your iPhone. Well, there're many reasons you need to backup your iPhone sms to the Mac. For example, your family or friends have sent you some important and you want to save them on your iPhone in case you delete them by accident, or you just need to backup your sms for other use. So today let's talk about how to move sms from iPhone to Mac. It would be very easy if you use an app to help you, I always use the iPhone to Mac transfer on Amacsoft to copy sms from iPhone to Mac. Now let me tell you how to use this great app: Step 1:Connect iPhone to Mac First of all, you need to install and launch the iPhone to Mac transfer, then connect your iPhone to Mac. The iPhone to Mac transfer would recognise your iPhone automatically. And all information of your iPhone will be shown on an interface. Step 2:Select sms and Start the Export Now you can see many choice on the left, find "SMS" and click it, all sms on your iPhone will be listed on the right. Select and check those you want to move, then just click "Export" on the top to start the transfer. Wait just a few a minute the transfer will be done. Great! You have finish the transfer now, it's really very easy, right? I believe it won't be a problem if you want to transfer your sms from iPhone to Mac. By the way you can also use this Amacsoft iPhone to Mac transfer to move other kind of files , like photos, songs etc. If you're a windows user, you can use iPhone to PC transfer on this web to move sms from iPhone to your PC just with the same steps, good luck!

  Read the article

• Intermittent "Lost connection to MySQL server at 'reading initial communication packet'"

  - by db2

  Our web environment consists of two servers. Web front-end. Dell PowerEdge R610, RHEL 5.5, Apache 2.2.17, php 5.2.14. Database server. Dell PowerEdge R710, Windows 2008 R2 Standard x64, MySQL 5.5.11-log x64. Normally these two work perfectly fine together. However, when I try to get them talking via a dedicated LAN on their secondary NICs (each machine has four of them), things get flaky. I have NIC #2 on both machines configured on the 172.16.1.0/24 subnet, with no gateway or DNS servers (obviously, since it's just those two systems), and I put the private IP address of each machine into the hosts file of the other. The routing tables on both machines look okay after I do this. I've tried this with both a crossover cable draped directly between the two NICs, and also via a dedicated vlan on the switch in the rack. In either case, I get intermittent connection problems. It's a fairly small percentage of connections that fail, but it's enough to cause a significant problem, and I have to switch back to the main network connection, which will contend with all the other traffic and hosts on the switch. The full error message that appears in the application log: SQLSTATE[HY000] [2013] Lost connection to MySQL server at 'reading initial communication packet', system error: 110 Am I doing something really dumb that's causing this to not work properly? Anything I can check in MySQL that would explain why it's failing to connect occasionally?

  Read the article

• Need to link WP Blog with Rails App on Heroku

  - by John Glass

  I have a client who wants to migrate his Rails app to Heroku. However the client also has a blog associated with his domain that runs on WordPress. Currently, the WordPress blog is running happily alongside the Rails app, but once we migrate to Heroku, that clearly won't be possible. The url for the app is like http://mydomain.com, and the url for the blog is like http://mydomain/blog. I realize that the best long-term solution is to redo the blog in a Rails format like Toto or Jekyll. But in the short term, what is the best way to continue hosting the WP blog where it is (or somewhere) but use Heroku to run the app? The client doesn't want the blog to be on a subdomain, but to remain at mydomain/blog for SEO reasons and also since there is traffic to the blog. I have two ideas: Use rack_rewrite or refraction (or just a regular old 301 and Apache mod_rewrite) on the old (non-Heroku) server to redirect the main url from the old site to Heroku. In this case, I can just leave the Wordpress blog running happily where it is. I think?? Is there a reason to choose one of those options (rack_rewrite, refraction, or mod_rewrite) over the others if I do it this way? Switch the DNS info to point to the Heroku site, and then use a 301 redirect from the blog to the old site. But then I'll have to get the old (non-Heroku) site on a subdomain and use some kind of rewrite rules anyway so it looks like it isn't a subdomain. Are either of these approaches preferable, or is there another way to do it that's easier that I'm missing?

  Read the article

• Running multiple services on different servers with IPv6 and a FQDN

  - by Mark Henderson

  One of the things NAT has permitted us to do in the past decade is split physical services onto different servers whilst hiding behind a single interface. For example, I have example.com behind a NAT on 192.0.2.10. I port-forward :80 and :443 to my web server. I'm also port forward :25 to my mail server, and :3389 to a terminal server and :8080 to the web interface of my computer that downloads torrents, and the story goes on. So I have 5 port forwardings going to 4 different computers on example.com. Then, I go and get me some neat IPv6. I assign example.com an IPv6 address of 2001:db8:88:200::10. That's great for my websites, but I want to go to example.com:8080 to get to my torrents, or example:3389 to log on to my terminal server. How can I do this with IPv6, as there is no NAT. Sure, I could create a bunch of new DNS entries for each new service, but then I have to update all my clients who are used to just typing example.com to get to either the website or the terminal server. My users are dumber than two bricks so they won't remember to connect to rdp.example.com. What options do I have for keeping NAT-style functionality with IPv6? In case you haven't figured it out, the above scenario is not a real scenario for me, or perhaps anyone yet, but it's bound to happen eventually. You know, with devops and all.

  Read the article

• Networking "chokes" on Windows 7 64 bit

  - by Rohit Nair

  I've been having this problem for some months now, and I have been unable to figure out a solution, or even the cause. At random points throughout the day, my internet connectivity "freezes". I don't get disconnected from my local wireless network. My router doesn't get disconnected from the world. However, for some reason, my computer stops receiving packets. If I'm playing an MMO ( World of Warcraft, in this case, but it has happened with Eve Online as well ) all activity just freezes. If I try to browse, Opera, Firefox and IE all stall at "Waiting for google.com..." or whatever the hostname may be. Inspection with a packet sniffer seems to reveal that there are no incoming packets. Here's the interesting part. Disconnecting from my wireless network and reconnecting fixes the issue. Obviously this led me to conclude that it was a problem with my router or wireless card. However, I have tweaked all the settings on my router that I could think of, including things like QoS, AP Isolation, etc. with no change. My wireless card doesn't really have that many options, and I have uninstalled and reinstalled drivers a few times without any change. Windows Firewall on/off doesn't make a difference. Anyone have any suggestions for debugging this? It's becoming an annoyance.

  Read the article

• My hard drive seems to be overheating... what should I do?

  - by George Edison

  After a cold boot, the hard drive in my notebook jumps to 56? within an hour or so of idling. Is 56? a cause for alarm? Notes: The notebook is on a flat desk and none of the vents are obstructed. The video card is currently at 55? and the CPU at 50?. It's a Western Digital 250GB hard drive. SMART reports the drive healthy but does warn that: Edit: this problem had a very surprise ending. I inverted the notebook and unscrewed some of the panels on the back (there was one covering the hard drive, and one that provided access to the memory). I couldn't see any dust, so I simply screwed everything back together and powered it on... and it worked! The temperature is now staying at 46?, and it feels notable cooler to the touch. So I can only assume that some internal fan was malfunctioning or something. Whatever the case, it's working now so I won't complain. Edit: I have an SSD now, so temperature isn't as big an issue as it was when I had a mechanical drive.

  Read the article

< Previous Page | 630 631 632 633 634 635 636 637 638 639 640 641  | Next Page >