Search Results

Search found 21352 results on 855 pages for 'bit shift'.

Page 650/855 | < Previous Page | 646 647 648 649 650 651 652 653 654 655 656 657  | Next Page >

• dom0 enable IPv6 for guests

  - by user98651

  I am looking at deploying IPv6 to my virtual machines. Right now I have v6 working great on the dom0 using a 6in4 provided by Hurricane Electric as I do not have native v6. However, I would like to distribute some of the /48 I am receiving to the domUs (/64 per machine would be ideal, but I am open to your suggestions). Static configuration on the domU side is fine. All I want to accomplish is getting the traffic to pass through the dom0 to the domU. To say the least, I'm still trying to wrap my head around all the virtual interfaces and bridges Xen creates. Yes, I have Googled around for this a bit and have not found anything great. I tried using two "vif-route6" bash scripts with no luck (possibly due to my ignorance with Xen networking). I am still stuck (mainly in how to configure the dom0). I would like to imagine this problem is relatively easy to solve and I look forward to your suggestions and help! Edited post to clarify my end goal: getting IPv6 to domU guests. I am completely open to suggestions but am hoping for something other than setting up a tunnel for every guest.

  Read the article

• OpenVPN bridge network from routed clients

  - by gphilip

  I have the following setup: subnet 1 - 10.0.1.0/24 with a machine used as NAT and also running an OpenVPN client subnet 2 - 192.168.1/24 with an OpenVPN server (the server in subnet 1 connect here) subnet 3 - 10.0.2.0/24 that uses the NAT machine (subnet 1) to access the internet, so all non-local traffic is routed there to the eth0 interface The OpenVPN client creates the tun0 interface and appropriate routing so that I can access machines from 192.168.1/24 [root@ip-10-0-1-208 ~]# telnet 192.168.1.186 8081 Trying 192.168.1.186... Connected to 192.168.1.186. Escape character is '^]'. [root@ip-10-0-1-208 ~]# route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 10.0.1.1 0.0.0.0 UG 0 0 0 eth0 10.0.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 10.8.0.1 10.8.0.5 255.255.255.255 UGH 0 0 0 tun0 10.8.0.5 0.0.0.0 255.255.255.255 UH 0 0 0 tun0 169.254.169.254 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 192.168.0.0 10.8.0.5 255.255.0.0 UG 0 0 0 tun0 However, when I try the same from subnet 3, it can't reach that machine. [root@ip-10-0-2-61 ~]# telnet 192.168.1.186 8081 Trying 192.168.1.186... I suspect that it's because subnet 3 is routed to eth0 on the NAT machine in subnet 1 and it cannot jump to tun0. What's the easiest way to resolve it? I don't want to use iptables. I can't change the routing from machines in subnet 1 because it's done in AWS and so it works only with specific interfaces. Also, the NAT machine gets its IP with DHCP and so bridging is a bit complicated. IP forwarding is set on the NAT machine [root@ip-10-0-1-208 ~]# cat /proc/sys/net/ipv4/ip_forward 1 Thank you!

  Read the article

• How to allow users to transfer files to other users on linux

  - by Jon Bringhurst

  We have an environment of a few thousand users running applications on about 40 clusters ranging in size from 20 compute nodes to 98,000 compute nodes. Users on these systems generate massive files (sometimes 1PB) controlled by traditional unix permissions (ACLs usually aren't available or practical due to the specialized nature of the filesystem). We currently have a program called "give", which is a suid-root program that allows a user to "give" a file to another user when group permissions are insufficient. So, a user would type something like the following to give a file to another user: > give username-to-give-to filename-to-give ... The receiving user can then use a command called "take" (part of the give program) to receive the file: > take filename-to-receive The permissions of the file are then effectively transferred over to the receiving user. This program has been around for years and we'd like to revisit things from a security and functional point of view. Our current plan of action is to remove the bit rot in our current implementation of "give" and package it up as an open source app before we redeploy it into production. Does anyone have another method they use to transfer extremely large files between users when only traditional unix permissions are available?

  Read the article

• Apache2 default vhost in alphabetical order or override with _default_ vhost?

  - by benbradley

  I've got multiple named vhosts on an Apache web server (CentOS 5, Apache 2.2.3). Each vhost has their own config file in /etc/httpd/vhosts.d and these vhost config files are included from the main httpd conf with... Include vhosts.d/*.conf Here's an example of one of the vhost confs... NameVirtualHost *:80 <VirtualHost *:80> ServerName www.domain.biz ServerAlias domain.biz www.domain.biz DocumentRoot /var/www/www.domain.biz <Directory /var/www/www.domain.biz> Options +FollowSymLinks Order Allow,Deny Allow from all </Directory> CustomLog /var/log/httpd/www.domain.biz_access.log combined ErrorLog /var/log/httpd/www.domain.biz_error.log </VirtualHost> Now I when anyone tries to access the server directly by using the public IP address, they get the first vhost specified in the aggregated config (so in my case it's alphabetical order from the vhosts.d directory). Anyone accessing the server directly by IP address, I'd like them to just get an 403 or a 404. I've discovered several ways to set a default/catch-all vhost and some conflicting opinions. I could create a new vhost conf in vhosts.d called 000aaadefault.conf or something but that feels a bit nasty. I could have a <VirtualHost> block in my main httpd.conf before the vhosts.d directory is included. I could just specify a DocumentRoot in my main httpd.conf What about specifying a default vhost in httpd.conf with _default_ http://httpd.apache.org/docs/2.2/vhosts/examples.html#default Would having a <VirtualHost _default_:*> block in my httpd.conf before I Include vhosts.d/*.conf be the best way for a catch-all?

  Read the article

• Wired to wireless bridge in Linux

  - by adrianmcmenamin

  I am attempting to set up my Raspberry Pi as a bridge (but I think this is not a question specific to the hardware) - using Debian wheezy. I have a hostapd.conf: (some details changed for security)... interface=wlan0 bridge=br0 driver=nl80211 auth_algs=1 macaddr_acl=0 ignore_broadcast_ssid=0 logger_syslog=-1 logger_syslog_level=0 hw_mode=g ssid=MY_SSID channel=11 wep_default_key=0 wep_key0=MY_KEY wpa=0 (yes, I know WEP is no good) And this in /etc/network/interfaces auto lo iface lo inet loopback iface eth0 inet dhcp allow-hotplug wlan0 iface wlan0 inet manual wpa-roam /etc/wpa_supplicant/wpa_supplicant.conf iface default inet dhcp auto br0 iface br0 inet dhcp bridge-ports eth0 wlan0 Everything seems to come up ok, but I cannot associate with the bridged wireless connection - even though the flashing lights on the USB stick suggest packets are being exchanged. I have read somewhere that not all cards/devices will run in hostap mode - they won't pass packets in one direction: is that right? (The info was a bit old)- this my card: [ 3.663245] usb 1-1.3.1: new high-speed USB device number 5 using dwc_otg [ 3.794187] usb 1-1.3.1: New USB device found, idVendor=0cf3, idProduct=9271 [ 3.804321] usb 1-1.3.1: New USB device strings: Mfr=16, Product=32, SerialNumber=48 [ 3.816994] usb 1-1.3.1: Product: USB2.0 WLAN [ 3.823790] usb 1-1.3.1: Manufacturer: ATHEROS [ 3.830645] usb 1-1.3.1: SerialNumber: 12345 So, what have I got wrong here?

  Read the article

• Troubleshooting an overheating CPU

  - by Jeff Fry

  I & my father just recently put together a new PC. Specs below. From the very beginning, on boot it will often complain that the CPU is too hot. If I sit in BIOS and watch the CPU, it'll drop back down from red to blue (<72C), at which point I've tended to just boot into Windows...and haven't had any problems. In fact, I've played a couple hours straight of Skyrim at max settings, and not had any visible issues. That said, I've occasionally walked away & come back to find that it's crashed. Yesterday, it crashed (while idle) twice in 12 hours, which shifted the balance from busy-with-life to nervous-I'm-about-to-melt-something. I just installed Core Temp which is showing my 4 cores fluxuating between 70-98C. I'm guessing at this point that the CPU fan may be incorrectly installed or defective. My first thought is to either (a) add water cooling (which the case supports) and / or (b) replace the CPU fan with an after-market one. That said, I'm very open to suggestions. A note, while I certainly don't want to burn money here, I have a baby coming any day now and am still unpacking from a recent move so if I have a choice between an option that costs money and another that takes a while...I'll happily spend a bit extra. Side question: Should I be nervous to even have this on at this point? Let me know if there's something useful I could add to my report. Otherwise, I'm looking forward to your suggestions! Thanks. CPU Intel i7-2600 CPU w/ stock fan Other HW ASUS P8Z68-V Pro motherboard 64G SSD boot drive 4 older SATA HDs GIGABYTE ATI Radeon HD6950 1 GB DDR5 8G Kingston T1 Series RAM Corsair 650W Gold Certified power supply Antec P280 case

  Read the article

• How to make an x.509 certificate from a PEM one?

  - by Ken

  I'm trying to test a script, locally, which involves uploading a file using a Java-based program to a FileZilla FTPES server. For the real thing, there is a real certificate on the FZ server, and the upload step (tested alone) seems to work fine. I've installed FileZilla Server on my dev box (so it'll test uploading from localhost to localhost). I don't have a real certificate for it, of course, so I used the "Generate new certificate..." button in FZ. It works fine from an interactive FTPES program (as long as I OK the unknown cert), but from my Java program it throws a javax.net.ssl.SSLHandshakeException ("unable to find valid certification path to requested target"). So how do I tell Java that this certificate is OK with me? (I know there's a way to change the Java program to accept any certificate, but I don't want to go down that route. I want to test it just as it will happen in production, and I don't want to ignore unknown certificates in production.) I found that Java has a program called "keytool" that seems to be for managing this sort of thing, but it complains that the certificate file that FZ generated is not an "x.509" file. A posting from the FZ side said it was "PEM encoded". I have "openssl" here, which looks like it's perfect for converting between certificate formats, but I think my understanding of certificate formats is wrong because I'm not seeing anything obvious. My knowledge of security certificates is a bit shaky, so if my title is stupidly wrong, please help by fixing that. :-)

  Read the article

• Why is windows not able to create a system partition?

  - by hughes

  I'm reinstalling Windows 7 64 bit, and I encountered an issue I've never seen before. I have a legit copy of Win 64 Professional, and I've installed it probably a half dozen times on this machine in the past without a problem. Googling the error only brings me to issues with people who are upgrading to win7. The drive itself seems to not have a problem. I can mount it on other systems and I can create an NTFS partition on it on other machines. I can install Ubuntu on it without any issues. Additionally, if I try using my alternate backup hard drive, the installer gives the same error. I have run diskpart from the setup page and clean seems to report that all is well. However, I cannot get past the screen below, which says Setup was unable to create a new system partition or locate an existing system partition. This happens regardless of whether or not the disk space is already allocated. What is causing this? How do I solve or get past this?

  Read the article

• Using Samba to share a folder from a Linux guest with a Windows host in VirtualBox

  - by AmV

  I would like to share a folder from a Linux Guest with a Windows host (with read and write access if possible) in VirtualBox. I read in these two links: here and here that it's possible to do this using Samba, but I am a little bit lost and I need more information on how to proceed. So far, I managed to set up two network adapters (one NAT and one host-only) and install Samba on the Linux guest, but now I have the following questions: What do I need to type in samba.conf to share a folder from the Linux guest? (the tutorial provided in one of the links above only explains how to share home directories) Are there any Samba commands that need to be executed on the guest to enable sharing? How do I make sure that these folders are only available to the host OS and not on the Internet? Once the Linux guest is setup, how do I access each of the individual shared folders from the Windows host? I read that I need to mount a drive on Windows to do this, but do I use Samba logins, or Linux logins, also do I use localhost? or do I need to set up an IP for this? Thanks!

  Read the article

• Boot records messed on dual boot (win7 and ubuntu) machine with SSD and HDD

  - by Michael

  i have a lenovo ideapad y570 with two hard drives: SSD and normal HDD both managed by RapidDrive and windows 7 pre-installed. First, i have shrunk my 500 GB HDD a little bit to make some place for a linux installation. Then i installed linux mint 12 to it, also installed grub onto the drive (dev/sdb). Installation programm has not allowed me to install grub on sda. Then i replaced linux mint with ubuntu 12.04 but installed grub onto the SSD (which is dev/sda and was the default-option). After that i could boot into my windows, only ubuntu worked. So i did a research, and tried: rewriting mbr of windows into sda1, reinstalling grub, replacing grub2 with grub-legacy, and now i think my partitions table are totally messed. Here is fdisk -l output: ubuntu@ubuntu:~$ sudo fdisk -l Disk /dev/sda: 64.0 GB, 64023257088 bytes 255 heads, 63 sectors/track, 7783 cylinders, total 125045424 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Device Boot Start End Blocks Id System /dev/sda1 * 2048 411647 204800 7 HPFS/NTFS/exFAT /dev/sda2 411648 1009430959 504509656 7 HPFS/NTFS/exFAT Disk /dev/sdb: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders, total 976773168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x5e5d1cc8 Device Boot Start End Blocks Id System /dev/sdb1 * 1979 884389887 442193954+ 12 Compaq diagnostics /dev/sdb2 884391934 976771071 46189569 5 Extended /dev/sdb5 884391936 937705471 26656768 83 Linux /dev/sdb6 937707520 967006207 14649344 83 Linux /dev/sdb7 967008256 976771071 4881408 82 Linux swap / Solaris I also cant mount any windows partitions to recover data. And when i open gparted, the whole sda-disk appears unallocated and it states "can not have a partition outside the disk!", also the end-sector address of /dev/sda2 confuses me. If i boot from the SSD, it throws some mbr error and wont boot, if i boot from the HDD, i only get the grub bash. How do i restore the partition tables? I can boot only from a live-cd at the machine. Thanks for any help.

  Read the article

• MySQL (local) owner and permissions

  - by Steve Nelson

  I asked this question on the MySQL forums and got no answer. I asked on StackOverflow and received a recommendation to try on ServerFault. So here I am. I recently successfully installed the 64 bit version of mysql-5.5.8 on a MacBook Pro in the /usr/local directory. To address a completely unrelated software (RVM actually) , I chown-ed my /usr/local directory to $USER, Which made MySQL very unhappy. It complained specifically about the /usr/local/mysql/data directory, so I chown-ed that directory to _mysql:wheel. Everything appears to work again, but it made me wonder if I would have been better off changing the owner of the whole /usr/local/mysql directory, not just the data subdirectory. Since I neglected to make notes of what owner the default installation runs under before rashly changing the owner of the /usr/local directory, could someone tell me what owner and permissions the /usr/local/mysql directory is by default if you don't inadvertently screw it up? :-/ In terms of permissions I'm guessing rwxr-xr-x would be appropriate (that's what the data directory currently has and it appears to be working fine), but reinforcement for that hunch would be appreciated. Thanks for any help. Steve

  Read the article

• CD/DVD Drive not detecting locally burned CD/DVDs, but works fine with Genuine discs.

  - by Rahul

  I'm using Dell Inspiron 1420 - 32 Bit - Windows Vista, since 2.5 years. I'm facing a strange problem with my CD/DVD-drive. I cannot run/play a CD/DVD which I get burned from my friends. But when I insert Genuine CD, I'm able to play/run it. And when I try to install my Vista package which I got with my notebook, the CD/DVD gets loaded. If I insert a CD/DVD which I get from my friend, CD doesn't get loaded and the system gets hanged. But all these CDs/DVDs work on other systems. I've tested it on many of my friends PCs. So, now I'm able to run only genuine CDs & a few genuine DVDs. My Experience/Experiments: I tried to install Windows Vista using Genuine DVD - It worked I tried to install Ubuntu which I got from shipped from Canonical Ltd. - It worked I tried to install OpenSUSE .iso file burned to a DVD in my friend's PC - It didn't work for me (But working perfectly fine in my friends PCs(Tested in 4 other PCs) Tried to play a DVD containing movies, burned in my friend's PC - It didn't work for me (But working perfectly fine in my friends PCs Any help/suggestions would be appreciated. Thanks.

  Read the article

• Cisco ASA site-to-site vpn not initiating phase 1 (not sending udp 500 packets)

  - by Sean Steadman

  I am hoping someone here can help me with my problem. I am trying to setup an IPSEC site-to-site VPN between two cisco ASA 5520's in GNS3 (both using 8.4.2). I have been unsuccesful in getting the tunnel up and it appears neither ASA is sending packets out,in regards to phase 1 and phase 2 (tested by using wireshark and seeing NO udp 500 packets). Doing show ipsec sa and such shows nothing. CALIFORNIA(config)# show ipsec sa There are no ipsec sas FLA-ASA# show ipsec sa There are no ipsec sas I will attach both configurations in two different pastebin files as to keep this post a bit cleaner. Essentially California side has 172.20.1.0/24 and Florida side has 10.10.10.0/24. California ASA config: http://pastebin.com/v0pngYzF Florida ASA config: http://pastebin.com/E2geybta Please let me know if there is any other vital information that could help. I have gotten IPSEC tunnels to work using openSwan (linux) and cisco routers but cannot for the life of me get ASA IPSEC tunnels to work. The ASDM is out of the question I only use cli. Thanks for any useful help!

  Read the article

• How do I share a complete XP disk so it can be seen from a Windows 7 system? (To move all files to a

  - by Ian Ringrose

  This should be easier! (both computers can see the internet etc so I know the network it’s self is working) I have a normal home network with a Windows XP machine on it and the new Windows 7 (64 bit) machine. So I can transfer the files to the new Windows 7 machine, I wish to share the complete disk (and all files) from the Windows XP machine and access them from the Windows 7 machine. Is there a step by step set of instructions for doing this anywhere? So fare I have: put both computers into the same workgroup put the windows 7 machine into work network mode so it can see the XP machine in the work group shared the XP disk as read only But when I try to access a lot of the folders on the XP disks, I am told I am not allowed to access them. (I was not asked for any passwords by the windows 7 machine when I accessed the XP machine. The XP machine just has its default account with no password set on it) The XP machine runs XP home and hence has "simple file shairing" turn on. So it seems that even if I create a admin account (with password) and connect with that account, it still comes in as "guest" on the XP machine. Chooseing to share the folder I want access to rather then the top of the disk drive seems to work, but is a pain as I need to share each user's folder with a different share name. If the new computer was not a laptop, I would just plug the hard disk from the old machine into it, but being a laptop I don't have that option.

  Read the article

• How to repair a corrupted Excel file

  - by SjoerdV

  I'm trying to restore some files for a friend who messed up a USB stick by pulling it out of the computer too soon. By searching invisible partitions I was able to restore the files. All files are intact, except 1 excel file that seems to be corrupted. I've googled about ways to repair an Excel file, because the default repair options in Excel 2003-2010 do not work for this file. I've came across a numerous third-party apps, of which the one seemes to be able to do the job: Recovery Toolbox for Excel. Of-course, this and all other apps I found require a purchase to actually repair the file. It seems a bit silly to pay 30 dollars for a one time thing, and something that is not for myself. So, I would like to keep that as a last-resort option. Is there anything I can try to fix this? I've attached a screenshot of how the file looks when I open it on my OSX when converted to a HTML file (to view the code), for the option that it could be a character set problem.

  Read the article

• Win7 'locking' process/files/folders?

  - by Dynde

  I've had a fair bit problems with sometimes files/folders/processes being 'locked' by Windows. The weird thing is, it's not like the traditional sense, I think, where tools like UnlockIT and wholockme would work. It seems that just giving it a little often helps - making me think it could either be the HDD, the memory, or something in Windows. A scenario: I go into a folder - don't open anything at all, go back up, cut or drag-move the folder to someplace else, it says "Action can't be completed because the folder or a file in it is open in another program". Waiting sometimes 20 seconds sometimes a little longer, and I can move it. Another scenario is deleting a bunch of files in a folder, and it appears that everything is gone, but then suddenly after a few seconds an .exe file pops back up, and I can't delete it. Waiting a few minutes, then pressing refresh and it's gone. I have the strangest feeling that there's a problem with either HDD or memory. I already tried disabling Windows indexing service with no luck. Does anyone have any ideas? EDIT: I should say, that I have a very fast system, 16 GB DDR3 RAM, i7-2600k CPU, SSD main HDD, so I really should not be experiencing any sort of problems, where one might say that it's "reasonable" for the system not to respond right away. Edit2: And I updated SSD firmware a couple months ago, so it shouldn't be bad release FW either

  Read the article

• Ubuntu network card problem.

  - by Steve Greene

  Hello folks, Several days ago, I installed Ubuntu 9.10 onto my Acer Aspire 3100 laptop, running it alongside Widows Vista as a dual-bootable system. Creation of the Ubuntu boot CD went fine, and the installation onto my hard drive was flawless. Ubuntu opens and behaves as I would expect, except for one little problem. For reasons unknown to me, Ubuntu is not communicating with my laptop's networking hardware, and I have no internet connectivity, it works fine under Windows Vista. Up in the right side of the Ubuntu desktop, I click on the network icon and it does not show a wireless connection at all. At home, where I use a dialup modem, I also see no means of getting online. My modem is an HDAUDIO Soft Data Fax Modem with Smart CP,manufactured by CXT (Conexant Systems Inc., file version 4.0.13.0, and the driver version is 7.58.0.0). I am an advanced computer user, but I am not a programmer. I seek a solution that is user-friendly for normal people, something equivalent to a driver that I can easily install or activate that will allow Ubuntu to see my hardware and get me connected. Can anyone help me over this hopefully-little glitch My processor is a Mobile AMD Sempron Processor 3500+ at 1.80 GHz, 1.50 GB RAM, and a 32-bit Operating System.

  Read the article

• Load balancing with puppet

  - by Gonçalo Queirós

  Hi there. Im trying to setup a loadbalancing system. My load balancer (nginx) has a conf file where i should list all IP's of the upstream servers. I could put the IP's on the conf manually, but this ways i would need to change the conf file every time i add/remove an upstream server. For now i came up with two different ideas, but i don't like much of neither: 1 - Have every upstream machine to use Exported Resources to create a file with it's IP..Then the load balancer server will have an "include conf_directory/*", and load all the files created by the upstrem servers. Since the load balancer is using nginx this can be done, but if i wan't latter on to configure something that doesn't have the "include" on the conf files, this solution will not work. 2 - If the config doesn't support the "include" command, then we could have again, every upstream server use the Exported Resources to create a filw with its IP, and latter on, the load balancer execute a command that would pick every file and generate the config Both versions addopt the same techinque, the difference is that version 2 is used when the server (that needs to have a conf generated) doesn't recognize a command like "include" inside its own conf. Now, my question is, is there any way to do this in a different form? I suspect that there is, since puppet is made to manage multiple servers, it seems a bit strange not have a easy way to configure load balancers.

  Read the article

• Performance decrease in every game and application

  - by Márk Vincze

  When I start a game, initially it runs smoothly, but after a couple of minutes, the performance gradually decreases to the point of being unplayable (1-2 FPS). The sound also starts to lag at this point. This does not happen every time I start my PC, usually exiting the game, rebooting, then starting the game again solves the problem, and I can play with perfect FPS for as long as I want. I could not find any deterministic reason when this happens and when doesn't. It happens in every game I tried (SWTOR, Diablo 3, Skyrim), and not even games, but simple applications like a browser or the Control Panel can get unusably slow. This is a brand new PC I bought three months ago, and this problem occurs since the first day I've been using it. Could you provide any advice how to further diagnose the problem? I tried to reinstall Windows, and tried different video card drivers, but it did not help. It would be important to know whether this is a hardware or software problem, because I can use the warranty if it is a hardware issue. (I did not want to return the PC yet, because I can't reproduce the issue deterministically.) Spec of the pc: Motherboard: ASROCK H61M-HVS CPU: INTEL Core i3-2120 3.30GHz 1155 BOX Memory: KINGMAX 4096MB DDR3 1333MHz KIT Video card: GIGABYTE GV-R685OC-1GD HD6850 1GB GDDR5 PCIE HDD: SEAGATE 500GB Barracuda 7200rpm 16MB SATA3 ST500DM002 I am using Windows 7 64 bit. Thanks a lot in advance!

  Read the article

• Large, high performance object or key/value store for HTTP serving on Linux

  - by Tommy

  I have a service that serves images to end users at a very high rate using plain HTTP. The images vary between 4 and 64kbytes, and there are 1.300.000.000 of them in total. The dataset is about 30TiB in size and changes (new objects, updates, deletes) make out less than 1% of the requests. The number of requests pr. second vary from 240 to 9000 and is dispersed pretty much all over, with few objects being especially "hot". As of now, these images are files on a ext3 filesystem distributed read only across a large amount of mid range servers. This poses several problems: Using a fileysystem is very inefficient since the metadata size is large, the inode/dentry cache is volatile on linux and some daemons tend to stat()/readdir() it's way through the directory structure, which in my case becomes very expensive. Updating the dataset is very time consuming and requires remounting between set A and B. The only reasonable handling is operating on the block device for backup, copying, etc. What I would like is a deamon that: speaks HTTP (get, put, delete and perhaps update) stores data it in an efficient structure. The index should remain in memory, and considering the amount of objects, the overhead must be small. The software should be able to handle massive connections with slow (if any) time needed to ramp up. Index should be read in memory at startup. Statistics would be nice, but not mandatory. I have experimented a bit with riak, redis, mongodb, kyoto and varnish with persistent storage, but I haven't had the chance to dig in really deep yet.

  Read the article

• NAT via iptables and virtual interface

  - by Alex

  I'm trying to implement the following scenario: One VM-host, multiple guest VMs, each one gets its own IP-address (and domain). Our server has only one physical interface, so the intended use is to add virtual interfaces on eth0. To complicate our situation the provider uses port-security on their switches, so I can't run the guest interfaces in bridged mode, because then the switch detects a "spoofed" MAC-address and kills the interface (permanently, forcing me to call the support, which I'm sure will get them a little bit angry the third time ;) ). My first guess was to use iptables and NAT to forward all packages from one virtual interface to another one, but iptables doesn't seem to like virtual interfaces (at least I can't get it to work properly). So my second guess is to use the source IP of the packages to the public interface. Let's assume libvirt creates a virbr0-network with 192.168.100.0/24 and the guest uses 192.168.100.2 as IP-address. This is what I tried to use: iptables -t nat -I PREROUTING --src public_ip_on_eth0:0 -p tcp --dport 80 -j DNAT --to-destination 192.168.100.2:80 That doesn't give me the intended results either (accessing the server times out). Is there a way to do what I'm trying to do, or even to route all traffic to a certain IP on a virtual interface to the VM's device?

  Read the article

• VMWare Workstation 8 Disk I/O & Hard Faults

  - by Scott

  I have VMWare Workstation 8 installed on a host machine with the following specs: Intel i5 2500k CPU 16GB DDR3 1600 ram 1TB Western Digital Caviar Black HD I have two Windows 7 virtual machines configured (currently running one at a time but will be operating both at once when my 32GB RAM kit arrives in a couple days). Each one is configured with 8GB of RAM and no tweaks/performance customizations or anything done. All of the VMWare settings are the defaults. When I boot into these machines and run various programs (Visual Studio, Outlook, etc), I can hear the disk thrashing quite a bit and checking Resource Monitor, I can see that I'm getting anywhere between 300-800 hard faults per second. From the host machine, it shows they're coming from the VMWare image. If I go to the virtual machine, whatever app I'm currently loading is the image that's causing the hard faults. As I understand it, hard faults are (simply) when an address in memory has been swapped out to the page file and has to be read from the page file instead of from memory. I don't understand why this is happening though. With 8GB of ram on the guest machine and 6.5GB available, what could be causing this? I know Windows 7 supposedly improved on page file management over XP but it seems excessive for this kind of slowdown, disk thrashing and high hard fault count when I have that much free RAM. Is there anything I can to to improve the performance in my guest machines? On the host machine, I can open/run any applications at all and hard faults stays around 0 with low disk I/O.

  Read the article

• Windows Vista/7 dropping Mac Server share points

  - by Hooligancat

  My Windows Vista and Windows 7 clients are having problems maintaining access to SMB shares on a Mac server. The initial connection to the server appears to be OK, as the Windows clients can see all of the server share points. However, the client randomly drops a couple of the server share points although the clients can still see the server. For example. If I have the following share points on the Mac server: Share A Share B Share C Share D Share E The Windows client can see these shares most of the time and can access them most of the time. But randomly a couple of the shares will just get dropped or go missing from the Windows client's ability to view them so I end up with something like: Share B Share D Share E All the share points are established int the same way with the same permission settings. My Mac OSX Server is set up with the following for SMB: SMB sharing enabled Standalone Server Workgroup of `CORPORATE` Allow Guest Access = YES Client connections limit = 100 Authentication: NTLMv2 & Kerberos and NTLM Code Page is Latin US (437) This is a workgroup master browser WINS registration is set to Enable WINS server (tried with setting off) Enable virtual share points for homes YES I noticed in my SMB file service log that the clients appear to connect OK, but I get the following error which implies a reset by either the server or the client: /SourceCache/samba/samba-187.9/samba/source/lib/util_sock.c:read_data(534) read_data: read failure for 4 bytes to client 192.168.0.99. = Connection reset by peer I am a bit stumped as to a direction to turn to try and get this to resolve. Continued attempts to access the server from the client will reconnect to the share points, but they inevitably get dropped again in the near future. Any and all help much appreciated.

  Read the article

• Why does the screen resolution of 1440x900 suddenly disappears from Intel GMA Control Panel?

  - by GeneQ

  I'm using a Vostro 1200 laptop with the Mobile Intel(R) 965 Express Chipset powering its graphics and running Vista 32-bit SP2 . I've been using the Vostro with a Dell SE198WFP LCD Monitor as the external display since day one for about two years without any problems. Recently, I plugged the Vostro into a couple of other monitors. The problem is, now the native resolution for my main monitor's (the SE198WFP) resolution of 1440x900 @ 60 Hz is no longer available. (See below) I've tried everything from uninstalling and reinstalling the Intel drivers as well as the monitor drivers to no avail. I've Goggled that this problem and it appears that this has happened to other people but all the answers involve people giving up in frustration or reinstalling; both terrible outcomes. Has anybody ever figured why this happens and have a good solution? Thanks. UPDATE: This dude has a complicated solution, which I haven't tried yet. His explanations for the problem was After an exausting search for an answer to the matter of why my brand new 19? widescreen monitor’s native resolution (1440×900) was unavailible (sic) in the display properties, I finally stumbled upon an article a person posted on Intel’s forums that basically explained what shannanigans Intel had been up to with their GMA 950 line of onboard graphic solutions. Not very comforting.

  Read the article

• How to remove Media Center from Windows 8

  - by Arabella

  I bought 2 Windows 8 upgrades, 1 for my PC and 1 for my notebook. I added Windows Media Center to my notebook using the free offer in November (side note: the key was emailed to me within 5 minutes, I see many people have been complaining that it takes a few days). Today I decided to add WMC to my PC as well, so I went onto the Microsoft website, same like last time, and I received the email within a few minutes. Once I added WMC, entered the key and the computer rebooted, my activation is now broken: This product key is already being used on another PC. Try a different key or buy a new one. After rereading the product key email, I realised that the WMC key was exactly the same as the one I had received in November for my notebook (I used the same email, i.e. my Microsoft account Outlook email, for both). I didn't think this would be a problem, as on Microsoft's feature pack page it states: ...is limited to five licenses per customer per promotion. So then I decided, I'll just remove WMC from my PC and go back to Windows 8 Pro. So I turned off the WMC feature, PC restarted, activation still broken because my key has been replaced. I then tried to activate it with my original Pro key. The error it gave was that this key cannot be used with this version of Windows, as it is now Windows 8 Pro with Media Center and not Windows 8 Pro anymore. I've searched a bit and it seems the only way to remove it is do a clean install. I tried the Windows 8 Downgrade Helper, which told me I was already running Win 8 Pro when I tried to downgrade, and that I was running Win 8 Pro with Media center when I tried the other option. To sum up: How do I remove Windows Media Center from Windows 8 Pro without having to do a clean install?

  Read the article

< Previous Page | 646 647 648 649 650 651 652 653 654 655 656 657  | Next Page >