Search Results

Search found 18329 results on 734 pages for 'interpret order'.

Page 652/734 | < Previous Page | 648 649 650 651 652 653 654 655 656 657 658 659  | Next Page >

• missing files after reassemble of RAID-5

  - by Kris_R

  I had to open my file-server's housing on Sunday to replace a faulty fan. What I didn't see was that one of the sata-cables was not properly connected. The 1st thing I did after a reboot was a check of the RAID status and it showed immediately that one drive is missing. Till this moment the device was not used (however it was mounted, so I'm not 100% sure that system did nothing). I stopped md0 and re-plugged the cable: mdadm --stop /dev/md0 poweroff After another reboot I checked the removed drive: mdadm --examine /dev/sdd1 ... Checksum : 3276bc1d - correct Events : 315782 Layout : left-symmetric Chunk Size : 32K Number Major Minor RaidDevice State this 0 8 49 0 active sync /dev/sdd1 0 0 8 49 0 active sync /dev/sdd1 1 1 8 65 1 active sync /dev/sde1 2 2 8 33 2 active sync /dev/sdc1 3 3 8 17 3 active sync /dev/sdb1 I was a bit surprised that it was shown as active (even if earlier mdadm said, that this device was removed from array) and its checksum was OK. I recreated RAID with: mdadm --assemble /dev/md0 --scan The command mdadm --detail /dev/md0 showed that all drives were running and system was in "clean" state. I mounted the device md0 and then came hic-cup. I wanted to work on one of the last files that I had been using before all the situation and it was not there. In another place I missed actually all files from the directory where I was working. As far as I can see most of the files that are older than a few days are intact but some newer ones are missing. Now the big question: what would be your advice? Is there a way to get these data? I thought about removing the drive that was earlier labeled by mdadm and rebuild array with another empty HDD. I've found that after re-assemble the "broken" drive has another label (changed from sdd to sdb). Can this have influence on rebuilt process? If yes, how to reassemble the array properly? I'm sure the SATA-cables are connected still in the same order to the controller. p.s. Please no advises like "restore from backup". I'm doing back-ups on Sunday's night and this happened in the late afternoon, so backup is not really options for me. p.s.s. I asked this question on Unix&Linux but no answer came up during last two days. I'm getting quite anxious. Sorry for duplicating if any of you reading the other forum.

  Read the article

• MySQL daemon keeps terminating unexpectedly

  - by Yehia A.Salam

  The MySQL daemon on my CentOS server keeps crashing, i got the logs from /var/logs/mysqld but still i am not sure how to fix this: 121114 16:22:56 mysqld_safe mysqld from pid file /var/run/mysqld/mysqld.pid ended 121114 21:55:11 mysqld_safe Starting mysqld daemon with databases from /var/lib/mysql 121114 21:55:11 [Note] Plugin 'FEDERATED' is disabled. 121114 21:55:11 InnoDB: The InnoDB memory heap is disabled 121114 21:55:11 InnoDB: Mutexes and rw_locks use GCC atomic builtins 121114 21:55:11 InnoDB: Compressed tables use zlib 1.2.3 121114 21:55:11 InnoDB: Using Linux native AIO 121114 21:55:11 InnoDB: Initializing buffer pool, size = 128.0M 121114 21:55:11 InnoDB: Completed initialization of buffer pool 121114 21:55:11 InnoDB: highest supported file format is Barracuda. InnoDB: The log sequence number in ibdata files does not match InnoDB: the log sequence number in the ib_logfiles! 121114 21:55:11 InnoDB: Database was not shut down normally! InnoDB: Starting crash recovery. InnoDB: Reading tablespace information from the .ibd files... InnoDB: Restoring possible half-written data pages from the doublewrite InnoDB: buffer... 121114 21:55:12 InnoDB: Waiting for the background threads to start 121114 21:55:13 InnoDB: 1.1.6 started; log sequence number 77177262 121114 21:55:13 [Note] Event Scheduler: Loaded 0 events 121114 21:55:13 [Note] /usr/libexec/mysqld: ready for connections. Version: '5.5.12' socket: '/var/lib/mysql/mysql.sock' port: 3306 MySQL Community Server (GPL) by Remi 121115 00:19:44 mysqld_safe Number of processes running now: 0 121115 00:19:44 mysqld_safe mysqld restarted 121115 0:19:47 [Note] Plugin 'FEDERATED' is disabled. 121115 0:19:47 InnoDB: The InnoDB memory heap is disabled 121115 0:19:47 InnoDB: Mutexes and rw_locks use GCC atomic builtins 121115 0:19:47 InnoDB: Compressed tables use zlib 1.2.3 121115 0:19:47 InnoDB: Using Linux native AIO 121115 0:19:47 InnoDB: Initializing buffer pool, size = 128.0M InnoDB: mmap(137363456 bytes) failed; errno 12 121115 0:19:47 InnoDB: Completed initialization of buffer pool 121115 0:19:47 InnoDB: Fatal error: cannot allocate memory for the buffer pool 121115 0:19:47 [ERROR] Plugin 'InnoDB' init function returned error. 121115 0:19:47 [ERROR] Plugin 'InnoDB' registration as a STORAGE ENGINE failed. 121115 0:19:47 [ERROR] Unknown/unsupported storage engine: InnoDB 121115 0:19:47 [ERROR] Aborting Edit #1 total used free shared buffers cached Mem: 496 370 126 0 24 110 -/+ buffers/cache: 234 261 Swap: 1023 9 1014 Edit #2 Also, largest table in my mysql is 20MB, so my the memory used should be pretty moderate. SELECT CONCAT(table_schema, '.', table_name), CONCAT(ROUND(table_rows / 1000000, 2), 'M') rows, CONCAT(ROUND(data_length / ( 1024 * 1024 * 1024 ), 2), 'G') DATA, CONCAT(ROUND(index_length / ( 1024 * 1024 * 1024 ), 2), 'G') idx, CONCAT(ROUND(( data_length + index_length ) / ( 1024 * 1024 * 1024 ), 2), 'G') total_size, ROUND(index_length / data_length, 2) idxfrac FROM information_schema.TABLES ORDER BY data_length + index_length DESC LIMIT 10;

  Read the article

• How to deny the web access to some files?

  - by Strae

  I need to do an operation a bit strange. First, i run on Debian, apache2 (which 'runs' as user www-data) So, I have simple text file with .txt ot .ini, or whatever extension, doesnt matter. These files are located in subfolders with a structure like this: www.example.com/folder1/car/foobar.txt www.example.com/folder1/cycle/foobar.txt www.example.com/folder1/fish/foobar.txt www.example.com/folder1/fruit/foobar.txt therefore, the file name always the same, ditto for the 'hierarchy', just change the name of the folder: /folder-name-static/folder-name-dinamyc/file-name-static.txt What I should do is (I think) relatively simple: I must be able to read that file by programs on the server (python, php for example), but if I try to retrieve the file contents by broswer (digiting the url www.example.com/folder1/car/foobar.txt, or via cUrl, etc..) I must get a forbidden error, or whatever, but not access the file. It would also be nice that even accessing those files via FTP are 'hidden', or anyway couldnt be downloaded (at least that I use with the ftp root and user data) How can I do? I found this online, be put in the file .htaccess: <Files File.txt> Order allow, deny Deny from all </ Files> It seems to work, but only if the file is in the web root (www.example.com / myfile.txt), and not in subfolders. Moreover, the folders in the second level (www.example.com/folder1/fruit/foobar.txt) will be dinamycally created.. I would like to avoid having to change .htaccess file from time to time. It is possible to create a rule, something like that, that goes for all files with given name, which is on www.example.com/folder-name-static/folder-name-dinamyc/file-name-static.txt, where those parts are allways the same, just that one change ? EDIT: As Dave Drager said, i could semplify this keeping those file outside the web accessible directory. But those directory's will contain others files too, images, and stuff used by my users, so i'm simply try to not have a duplicate folders system, like: /var/www/vhosts/example.com/httpdocs/folder1/car/[other folders and files here] /var/www/vhosts/example.com/httpdocs/folder1/cycle/[other folders and files here] /var/www/vhosts/example.com/httpdocs/folder1/fish/[other folders and files here] //and, then for the 'secrets' files: /folder1/data/car/foobar.txt /folder1/data/cycle/foobar.txt /folder1/data/fish/foobar.txt

  Read the article

• MySQL: Pacemaker cannot start the failed master as a new slave?

  - by quanta

  I'm going to setup failover for MySQL replication (1 master and 1 slave) follow this guide: https://github.com/jayjanssen/Percona-Pacemaker-Resource-Agents/blob/master/doc/PRM-setup-guide.rst Here're the output of crm configure show: node serving-6192 \ attributes p_mysql_mysql_master_IP="192.168.6.192" node svr184R-638.localdomain \ attributes p_mysql_mysql_master_IP="192.168.6.38" primitive p_mysql ocf:percona:mysql \ params config="/etc/my.cnf" pid="/var/run/mysqld/mysqld.pid" socket="/var/lib/mysql/mysql.sock" replication_user="repl" replication_passwd="x" test_user="test_user" test_passwd="x" \ op monitor interval="5s" role="Master" OCF_CHECK_LEVEL="1" \ op monitor interval="2s" role="Slave" timeout="30s" OCF_CHECK_LEVEL="1" \ op start interval="0" timeout="120s" \ op stop interval="0" timeout="120s" primitive writer_vip ocf:heartbeat:IPaddr2 \ params ip="192.168.6.8" cidr_netmask="32" \ op monitor interval="10s" \ meta is-managed="true" ms ms_MySQL p_mysql \ meta master-max="1" master-node-max="1" clone-max="2" clone-node-max="1" notify="true" globally-unique="false" target-role="Master" is-managed="true" colocation writer_vip_on_master inf: writer_vip ms_MySQL:Master order ms_MySQL_promote_before_vip inf: ms_MySQL:promote writer_vip:start property $id="cib-bootstrap-options" \ dc-version="1.0.12-unknown" \ cluster-infrastructure="openais" \ expected-quorum-votes="2" \ no-quorum-policy="ignore" \ stonith-enabled="false" \ last-lrm-refresh="1341801689" property $id="mysql_replication" \ p_mysql_REPL_INFO="192.168.6.192|mysql-bin.000006|338" crm_mon: Last updated: Mon Jul 9 10:30:01 2012 Stack: openais Current DC: serving-6192 - partition with quorum Version: 1.0.12-unknown 2 Nodes configured, 2 expected votes 2 Resources configured. ============ Online: [ serving-6192 svr184R-638.localdomain ] Master/Slave Set: ms_MySQL Masters: [ serving-6192 ] Slaves: [ svr184R-638.localdomain ] writer_vip (ocf::heartbeat:IPaddr2): Started serving-6192 Editing /etc/my.cnf on the serving-6192 of wrong syntax to test failover and it's working fine: svr184R-638.localdomain being promoted to become the master writer_vip switch to svr184R-638.localdomain Current state: Last updated: Mon Jul 9 10:35:57 2012 Stack: openais Current DC: serving-6192 - partition with quorum Version: 1.0.12-unknown 2 Nodes configured, 2 expected votes 2 Resources configured. ============ Online: [ serving-6192 svr184R-638.localdomain ] Master/Slave Set: ms_MySQL Masters: [ svr184R-638.localdomain ] Stopped: [ p_mysql:0 ] writer_vip (ocf::heartbeat:IPaddr2): Started svr184R-638.localdomain Failed actions: p_mysql:0_monitor_5000 (node=serving-6192, call=15, rc=7, status=complete): not running p_mysql:0_demote_0 (node=serving-6192, call=22, rc=7, status=complete): not running p_mysql:0_start_0 (node=serving-6192, call=26, rc=-2, status=Timed Out): unknown exec error Remove the wrong syntax from /etc/my.cnf on serving-6192, and restart corosync, what I would like to see is serving-6192 was started as a new slave but it doesn't: Failed actions: p_mysql:0_start_0 (node=serving-6192, call=4, rc=1, status=complete): unknown error Here're snippet of the logs which I'm suspecting: Jul 09 10:46:32 serving-6192 lrmd: [7321]: info: rsc:p_mysql:0:4: start Jul 09 10:46:32 serving-6192 lrmd: [7321]: info: RA output: (p_mysql:0:start:stderr) Error performing operation: The object/attribute does not exist Jul 09 10:46:32 serving-6192 crm_attribute: [7420]: info: Invoked: /usr/sbin/crm_attribute -N serving-6192 -l reboot --name readable -v 0 The full logs: http://fpaste.org/AyOZ/ The strange thing is I can starting it manually: export OCF_ROOT=/usr/lib/ocf export OCF_RESKEY_config="/etc/my.cnf" export OCF_RESKEY_pid="/var/run/mysqld/mysqld.pid" export OCF_RESKEY_socket="/var/lib/mysql/mysql.sock" export OCF_RESKEY_replication_user="repl" export OCF_RESKEY_replication_passwd="x" export OCF_RESKEY_test_user="test_user" export OCF_RESKEY_test_passwd="x" sh -x /usr/lib/ocf/resource.d/percona/mysql start: http://fpaste.org/RVGh/ Did I make something wrong?

  Read the article

• How to setup phpmyadmin with nginx and access it from http://vps-ip/phpmyadmin

  - by Danny

  The phpmyadmin files are located here /usr/share/phpmyadmin/ And I have this server block code that allows me to access phpmyadmin only from http://vps-ip/: server { listen 80; ## listen for ipv4; this line is default and implied #listen [::]:80 default ipv6only=on; ## listen for ipv6 root /usr/share/phpmyadmin/; index index.php index.html index.htm; server_name ein; location / { root /usr/share/phpmyadmin/; index index index.php; try_files $uri/ $uri /index.php?q=$uri&amp&$args; port_in_redirect off; } location ~* ^.+.(jpg|jpeg|gif|css|png|js|ico|xml)$ { access_log off; log_not_found off; expires max; root /usr/share/phpmyadmin/; } location ~ \.php$ { fastcgi_split_path_info ^(.+\.php)(/.+)$; #NOTE: You should have "cgi.fix_pathinfo = 0;" in php.ini fastcgi_pass php; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME /usr/share/phpmyadmin/$fastcgi_script_name; include fastcgi_params; fastcgi_param QUERY_STRING $query_string; fastcgi_param REQUEST_METHOD $request_method; fastcgi_param CONTENT_TYPE $content_type; fastcgi_param CONTENT_LENGTH $content_length; fastcgi_intercept_errors on; fastcgi_ignore_client_abort off; fastcgi_connect_timeout 60; fastcgi_send_timeout 360; fastcgi_read_timeout 360; fastcgi_buffer_size 128k; fastcgi_buffers 8 256k; fastcgi_busy_buffers_size 256k; fastcgi_temp_file_write_size 256k; } location ~ /.htaccess { deny all; log_not_found off; access_log off; } location ~ /.htpasswd { deny all; log_not_found off; access_log off; } location = /favicon.ico { allow all; log_not_found off; access_log off; } location = /robots.txt { allow all; log_not_found off; access_log off; } } What changes I need to do in order to access phpmyadmin from http://vps-ip/phpmyadmin ?

  Read the article

• The Cindy Shearin Group: New Scam Targets Renters in the Area

  - by user226089

  MONROE - Craigslist is a popular site when trying to find that perfect deal on a rental home or apartment. Experts warn some of these rental ads aren't what they seem. We decided to take a look. On our Craigslist search we found this house for rent. The problem is this home’s not for rent - it's for sale. “I think it’s a huge deal,” said Shane Wooten, the realtor for this home in Monroe. His properties have become the target of a common scam, aimed at taking your money. "It looks like they're trying to scam them out of their deposit and first months rent," adds Wooten. He says scammers copy and paste the sale ad's from legitimate realtor sites to Craigslist as rental ads. "I can usually tell when one hits craigslist because I’ll usually get 20 to 30 phone calls that day." They then pretend to be out of town on business or personal matters, and give only an email address as a point of contact. Usually they'll ask for money up front on a deal too good to miss. "You'll have a house that's supposed to rent for $950-1000 a month, and they'll have it renting for $600 a month,” says Wooten During our conversation, he shows us text messages from one scammer who says he'll mail the keys to this house if Wooten wires money for a deposit and first months rent. Jo Ann Deal of the Better Business Bureau says scammers are getting better at making themselves out to be realtors. "We’re really concerned for our real estate agents with this scam," says Deal. She says that realtors have to be more on top of their vacant homes in order to protect their businesses. So how can you tell if the house you want is really for rent? She says if the home owner lives out of the country, can't meet face to face or asks for a payment through a money wire it's probably a scam. “There are some catch-lines you watch for,” says Deal. “If the marketing is really good but there's no phone number, no physical address and they will communicate with you only by email and you can do it today, then it's probably a scam." You should always report fishy ad's to Craigslist or the BBB and never send money through a wire transfer.

  Read the article

• Windows 7 x64 installation freezes on new PC build

  - by jhsowter

  Symptoms While attempting to install Windows 7 (64 bit) on my new PC build, it freezes usually at the point where it is expanding the windows image, but has frozen as early as accepting the licence agreement, and as late as just after the first restart. My specs are at the bottom of the post. So far I have tried the following to identify the problem, in rough chronological order: Tried different hard drives with different sata cables. Same symptoms. I later used a different computer to install windows on the same hard drive with no problems. Tried the RAM in different slots, and tried one RAM stick instead of two. Same symptoms. Updated the BIOS to 1.60. Same symptoms. Ran Memtest86+ with RAM in dual channel. It passed about 6 times when I left it running overnight. Used USB to install windows instead of an optical drive. Same symptoms. Change SATA configuration from AHCI to IDE. Same symptoms. Tried various different SATA ports. Same symptoms. Updated BIOS to 1.70. Same symptoms. I saw the RAM did not list my motherboard as being supported even though the motherboard did list the RAM as being supported. So I tried some Kingston DDR3 1333MHz RAM instead. Same symptoms. Other (possibly) pertinent information My CPU idles at about 30 °C. I can't tell what it gets to when it's working. When I installed the CPU, the lever which locks the CPU in place took quite a bit of force to pull down. Now I didn't just yank it down without rechecking the CPU was seated properly about 5 times, but it does seems unusual, and I wonder if the CPU was seated badly if I would see these symptoms? I am out of ideas and don't know how to diagnose any further. I suppose either the motherboard or CPU must be the problem. I am on the verge of taking it to a specialist. The Question How should I proceed from here? Is there anything I can rule out as being the source of the symptoms I am seeing? My Specs CPU: Intel i5 3570k RAM: G.Skill RipjawsX 8GB kit HDD: single 3.5" 500GB SATA or 160GB 2.5" SATA (at different times and sometime together. But no RAID or anything). MB: ASRock Extreme4 Z77 PSU: Silverstone Strider Plus 600W ST60F-P

  Read the article

• Some DHCP clients end up with wrong DNS server

  - by Nic Waller

  The scenario: DC running Windows Server 2008 R2 providing DNS + DHCP Cisco 1811 Router as the gateway 30 Windows XP DHCP clients on the LAN The problem: Some workstations are spontaneously switching to an incorrect DNS server. Specifically, ipconfig /all shows that they start using the gateway as a DNS server. This happens about 5-10 times a day to various computers, sometimes more than once per day. The workaround: Repairing the connection on the XP client always fixes the problem, and the correct DNS server address is obtained. We lost our main DNS/DHCP machine a week ago, and had to bring this one online as a spare. We've been having this issue since then. DHCP leases on the old and new servers are configured for "wired" (8 day) duration. There are definitely no other DHCP servers active on the LAN. So far there is no discernible pattern about which clients will show this problem, or when. When I ran DCDIAG /test:DNS it came back clean. Manual inspection of the DNS zone shows that all the records are appearing as expected, with no traces of the previous machine in there. Update Feb 27: Added screenshots. Here is a screenshot of the DHCP scope options on the 2008 R2 server. And here is a screenshot of ipconfig /all running on a healthy host. I don't have any ailing hosts at the moment, but will grab a screencap next time it happens. Update Feb 28: More screenshots. Here's a screenshot of DHCP and DNS traffic from a healthy client when repairing the local area connection. There's definitely only one server responding, but it does seem strange that the negotiation takes place twice. I'll try to get a similar capture from a sick machine this coming week. Update Mar 01: Caught a bad ipconfig. Here's a screenshot of ipconfig /all from a client that had this issue. It says the lease was issued this morning, but it doesn't even have an entry for the secondary DNS I set up yesterday. Both DNS servers were discovered properly when repairing the connection. Update Mar 01: It even got the sysadmin! This issue finally affected my personal workstation this morning. Unfortunately I had just rebooted and wasn't running a packet dump at the time. I set up a secondary server yesterday, and was logging all DNS traffic to it. My machine had not contacted the secondary DNS in over half an hour, so that says to me that it's just spontaneously reverting to the gateway without even failing over to secondary DNS first. Today I swapped the order of the DNS servers in DHCP, so the secondary is primary and vice versa. I will update again once I know how that goes.

  Read the article

• DPM 2010 "Disk failed or disk not found"

  - by SysAdmin

  I have an HP Proliant ML110 G5 server with Windows server 2008R2 only dedicated for DPM 2010. This server has a limit in HD of 8TB which has already been met. I'm now stuck in this situation where my disk keeps failing "Disk failed or Disk not found" in the disk management. Only after I reboot the system the disk comes back up. Today I was running my monthly tape backup on a certain protection group and the disk failed again while the tape job was running (so the job wasn't completed). This is the description of the error in the alerts: "The disk Disk 1 - Hitachi HDS722020ALA330 SCSI Disk Device cannot be detected or has stopped responding. All subsequent protection activities that use this disk will fail until the disk is brought back online. (ID 3120)". My backup system is becoming useless! I don't think that is a hardware issue (please correct me if I'm wrong) since the HD works fine for a certain period of time which is becoming shorter and shorter. I basically have no more option to fix this problem. I tried to fix any error that was coming up in the event viewer with no luck (included one regarding the SQL2008 compatibility issue). The disk keeps failing! Now I'm only trying to recover/migrate the data from the disk that is having problem but my issue now is that I cannot add any drives to my server since I already got installed the maximum storage capacity 8TB. I thought about 2 simple options. Please tell me what you guys think about it; Unplug one of the 2 storage pool disks (disk0, that one without problem) from the machine and install a new one in order to migrate the data with the Migration tool for DPM. Remove the defective disk (disk1), put back the disk0 and run the synchronization/consistency check on all the groups to recreate replicas and recovery points. Run diskpart.exe and clean up the disk (loosing all data) and hoping that he will work after I sync all the protection groups. Both solutions are not elegant but I have no better options at the moment. Please I need some help. Thanks for your time Angelo

  Read the article

• Varnish configuration to only cache for non-logged in users

  - by davidsmalley

  I have a Ruby on Rails application fronted by varnish+nginx. As most of the sites content is static unless you are a logged in user, I want to cache the site heavily with varnish when a user is logged out but only to cache static assets when they are logged in. When a user is logged in they will have the cookie 'user_credentials' present in their Cookie: header, in addition I need to skip caching on /login and /sessions in order that a user can get their 'user_credentials' cookie in the first place. Rails by default does not set a cache friendly Cache-control header, but my application sets a "public,s-max-age=60" header when a user is not logged in. Nginx is set to return 'far future' expires headers for all static assets. The configuration I have at the moment is totally bypassing the cache for everything when logged in, including static assets — and is returning cache MISS for everything when logged out. I've spent hours going around in circles and here is my current default.vcl director rails_director round-robin { { .backend = { .host = "xxx.xxx.xxx.xxx"; .port = "http"; .probe = { .url = "/lbcheck/lbuptest"; .timeout = 0.3 s; .window = 8; .threshold = 3; } } } } sub vcl_recv { if (req.url ~ "^/login") { pipe; } if (req.url ~ "^/sessions") { pipe; } # The regex used here matches the standard rails cache buster urls # e.g. /images/an-image.png?1234567 if (req.url ~ "\.(css|js|jpg|jpeg|gif|ico|png)\??\d*$") { unset req.http.cookie; lookup; } else { if (req.http.cookie ~ "user_credentials") { pipe; } } # Only cache GET and HEAD requests if (req.request != "GET" && req.request != "HEAD") { pipe; } } sub vcl_fetch { if (req.url ~ "^/login") { pass; } if (req.url ~ "^/sessions") { pass; } if (req.http.cookie ~ "user_credentials") { pass; } else { unset req.http.Set-Cookie; } # cache CSS and JS files if (req.url ~ "\.(css|js|jpg|jpeg|gif|ico|png)\??\d*$") { unset req.http.Set-Cookie; } if (obj.status >=400 && obj.status <500) { error 404 "File not found"; } if (obj.status >=500 && obj.status <600) { error 503 "File is Temporarily Unavailable"; } } sub vcl_deliver { if (obj.hits > 0) { set resp.http.X-Cache = "HIT"; } else { set resp.http.X-Cache = "MISS"; } }

  Read the article

• Block Google requests to 16k using pf firewall

  - by atmosx

  I'd like to block access to Google search using PF after the threshold of 17500 requests (connection established) in 24h, from a host running FreeBSD 9. What I came up with, after reading pf-faq is this rule: pass out on $net proto tcp from any to 'www.google.com' port www flags S/SA keep state (max-src-conn 200, max-src-conn-rate 17500/86400) NOTE: 86400 are 24h in seconds. The rule should work, but PF is smart enough to know that www.google.com resolves in 5 different IPs. So my pfctl -sr output gives me this: pass out on vte0 inet proto tcp from any to 173.194.44.81 port = http flags S/SA keep state (source-track rule, max-src-conn 200, max-src-conn-rate 17500/86400, src.track 86400) pass out on vte0 inet proto tcp from any to 173.194.44.82 port = http flags S/SA keep state (source-track rule, max-src-conn 200, max-src-conn-rate 17500/86400, src.track 86400) pass out on vte0 inet proto tcp from any to 173.194.44.83 port = http flags S/SA keep state (source-track rule, max-src-conn 200, max-src-conn-rate 17500/86400, src.track 86400) pass out on vte0 inet proto tcp from any to 173.194.44.80 port = http flags S/SA keep state (source-track rule, max-src-conn 200, max-src-conn-rate 17500/86400, src.track 86400) pass out on vte0 inet proto tcp from any to 173.194.44.84 port = http flags S/SA keep state (source-track rule, max-src-conn 200, max-src-conn-rate 17500/86400, src.track 86400) PF creates 5 different rules, 1 for each IP that Google resolves. However I have the sense - without being 100% sure, I didn't had the chance to test it - that the number 17500/86400 applies for each IP. If that's the case - please confirm - then it's not what I want. In pf-faq there's another option called source-track-global: source-track This option enables the tracking of number of states created per source IP address. This option has two formats: + source-track rule - The maximum number of states created by this rule is limited by the rule's max-src-nodes and max-src-states options. Only state entries created by this particular rule count toward the rule's limits. + source-track global - The number of states created by all rules that use this option is limited. Each rule can specify different max-src-nodes and max-src-states options, however state entries created by any participating rule count towards each individual rule's limits. The total number of source IP addresses tracked globally can be controlled via the src-nodes runtime option. I tried to apply source-track-global in the above rule without success. How can I use this option in order to achieve my goal? Any thoughts or comments are more than welcome since I'm an amateur and don't fully understand PF yet. Thanks

  Read the article

• The server rejected the session-establishment request: WCF hosted on IIS

  - by Dave Hanna

  Background: I'm working on a project where we have about a dozen distinct WCF services implemented in an IIS application, communicating over net.tcp on the default port (808), using the Microsoft Net.Tcp Port Sharing Service. I recently added a self-test method to the base class of each of these services so that I could remotely hit the service and get back a status string verifying that it was in operation. We implement this app in a ladder of environments - Development, QA, UAT, and finally production. My problem: My test program, which instantiates a connection to each service in turn and invokes the self-test method, works fine on all the environments below production. We recently moved the app to production, and I'm getting a weird error that I can't explain: On the first of the services that I hit, I get back an exception: "The server at [URL] rejected the session-establishment request". All the other services respond fine. I initially thought there was something wrong with the particular service that was failing, but I tried rearranging the list of services into a different order, and it SEEMS to always be the first service that I hit that fails. (I say SEEMS because it think once in the early iterations of testing, I saw it happen on the second service that it hit. But I haven't been able to reproduce that.) I've looked at application startup delays, and that doesn't seem to be the problem, because I can come back and run the test again as soon as it finishes - a delay of only a minute or two - and get the same error. Also, in the lower level environments, there is a start up delay of probably 30 seconds to a minute, but the result still comes back as expected. I've tried accessing the services over http from INetManager, and I get intermittent failures on all the services - a particular service will return a yellow screen of death on on invocation, then come up with the expected link to the WSDL on the next one seconds later. I'm completely at a loss to explain this behavior, or how to resolve it. I've googled the error message, and not found anything helpful. It may be a configuration issue - the production servers are newly provisioned VM's, and we may not have the config exactly right (whereas all the lower level environments have been running this and other similar apps for some time), but I have not idea what to look for. I've looked at the properties of the app pool that the app is running on and compared it to the lower level environments without finding any differences. If somebody can point me in the right direction, you would have my undying gratitude.

  Read the article

• Windows 7 x64 "upgrade" repair fails

  - by Polynomial

  I've been running into issues with Windows Update, which I can't seem to fix. The hotfixes don't work, nor does the Windows update readyness tool, or the manual SP1 upgrade. I get various esoteric errors which nobody seems to have a fix for. Looks like some of the update cache is corrupt and digital signatures seem to be broken on some packages / Windows Update components. Long story short, I have discovered the only option is to do a repair operation on the OS, to repair everything. It's so corrupt that only a complete replacement will fix it. According to various sources (including MSKB) one can perform a repair by running an in-place upgrade. I've got the Windows 7 Ultimate retail disc, which I've inserted into my machine. I ran setup.exe and went through in the following order: Install now Go online to get latest updates (I've also tried not getting updates) Wait for updates to be downloaded Select Windows 7 Ultimate (x64 architecture) and click next Accept the T&Cs, click next Click Upgrade At this point it spends a minute on the "checking compatibility" screen, after which I get the following error: The following issues are preventing Windows from upgrading. Cancel the upgrade, complete each task, and then restart the upgrade to continue. You can’t upgrade 64-bit Windows to a 32-bit version of Windows. To upgrade, obtain a 64-bit version of the installation disc, or go online to see how to install Windows 7 and keep your files and settings. 32-bit Windows cannot be upgraded to a 64-bit version of Windows. To upgrade, obtain a 32-bit version of the Windows installation disc. It also mentions a warning about potential conflicts with a storage driver and VS2010, but that doesn't seem to be the blocking issue. My currently installed version of Windows is Ultimate 64-bit (absolutely sure of this) and the disc is definitely a x86 / x64 combined Ultimate retail disc. There seem to be a few people who have run into this (e.g. this question), but I've not seen any answers. I've checked the event viewer, but can't spot anything in there that's related. Any idea how I can get this working? P.S: Just to pre-empt the inevitable "are you suuuuuuuuuuuuure it's x64 Ultimate?" questions:

  Read the article

• Is dual-booting an OS more or less secure than running a virtual machine?

  - by Mark

  I run two operating systems on two separate disk partitions on the same physical machine (a modern MacBook Pro). In order to isolate them from each other, I've taken the following steps: Configured /etc/fstab with ro,noauto (read-only, no auto-mount) Fully encrypted each partition with a separate encryption key (committed to memory) Let's assume that a virus infects my first partition unbeknownst to me. I log out of the first partition (which encrypts the volume), and then turn off the machine to clear the RAM. I then un-encrypt and boot into the second partition. Can I be reasonably confident that the virus has not / cannot infect both partitions, or am I playing with fire here? I realize that MBPs don't ship with a TPM, so a boot-loader infection going unnoticed is still a theoretical possibility. However, this risk seems about equal to the risk of the VMWare/VirtualBox Hypervisor being exploited when running a guest OS, especially since the MBP line uses UEFI instead of BIOS. This leads to my question: is the dual-partitioning approach outlined above more or less secure than using a Virtual Machine for isolation of services? Would that change if my computer had a TPM installed? Background: Note that I am of course taking all the usual additional precautions, such as checking for OS software updates daily, not logging in as an Admin user unless absolutely necessary, running real-time antivirus programs on both partitions, running a host-based firewall, monitoring outgoing network connections, etc. My question is really a public check to see if I'm overlooking anything here and try to figure out if my dual-boot scheme actually is more secure than the Virtual Machine route. Most importantly, I'm just looking to learn more about security issues. EDIT #1: As pointed out in the comments, the scenario is a bit on the paranoid side for my particular use-case. But think about people who may be in corporate or government settings and are considering using a Virtual Machine to run services or applications that are considered "high risk". Are they better off using a VM or a dual-boot scenario as I outlined? An answer that effectively weighs any pros/cons to that trade-off is what I'm really looking for in an answer to this post. EDIT #2: This question was partially fueled by debate about whether a Virtual Machine actually protects a host OS at all. Personally, I think it does, but consider this quote from Theo de Raadt on the OpenBSD mailing list: x86 virtualization is about basically placing another nearly full kernel, full of new bugs, on top of a nasty x86 architecture which barely has correct page protection. Then running your operating system on the other side of this brand new pile of shit. You are absolutely deluded, if not stupid, if you think that a worldwide collection of software engineers who can't write operating systems or applications without security holes, can then turn around and suddenly write virtualization layers without security holes. -http://kerneltrap.org/OpenBSD/Virtualization_Security By quoting Theo's argument, I'm not endorsing it. I'm simply pointing out that there are multiple perspectives here, so I'm trying to find out more about the issue.

  Read the article

• Windows 7 remains powered on when restarting

  - by BombDefused

  I'm running windows 7 x64 on an MSI P67A-GD53 motherboard, in an Antec P280 Super Midi Towercase with a Corsair 650w PSU. I've just installed a second instance of windows 7 x64 on a separate disk (this is to keep my games separate from my work OS). The problem is that it appears now that I cannot restart from either instance of Windows 7. The shut down command, and sleep commands work as expected. When I try to restart, the shutdown happens but the system never reboots. Everything remains powered on, until I hold down the power button to force the power off. Ithink (but am not 100% sure) this has only started since I installed the second OS, and am assuming this has something to do with the motherboard needing to know which OS to run up again? Some other forums I've read suggest that the PSU has a major role in restart and could be at fault. Changing the boot order of the disks in the BIOS does not change anything. Any suggestions greatfully recieved! Update: I now have a reproduceable issue: I think the secondary OS install may have been a red herring. It was when windows tried to reboot during the install that I noticed the issue. After playing around with installing drivers, and rebooting many many times, I have found that it is the OC genie setting on the MSI motherboard that seems to trigger the problem. This makes sense as I only started using the OC genie feature a couple of weeks ago, and probably hadn't used restart in that time. However... simply turning off OC genie does not make the issue go away. I have to turn off OC genie, shutdown, start enter bios, go to the "Save and Exit" menu "Restore Defaults" yes to "Load optimized defaults", which will reset to clear the problem. Now when the PC boots into windows, I can restart as normal (and from the OS on either HDD). I only know how to control the issue, and don't still know the root cause. I'd like to be able to use the OC genie function if anyone can suggest a why I'm seeing this problem. Could it be that I'm drawing too much power when using OC feature?

  Read the article

• PHP & MySQL on Mac OS X: Access denied for GUI user

  - by Eirik Lillebo

  Hey! This question was first posted to Stack Overflow, but as it is perhaps just as much a server issue I though it might be just as well to post it here also. I have just installed and configured Apache, MySQL, PHP and phpMyAdmin on my Macbook in order to have a local development environment. But after I moved one of my projects over to the local server I get a weird MySQL error from one of my calls to mysql_query(): Access denied for user '_securityagent'@'localhost' (using password: NO) First of all, the query I'm sending to MySQL is all valid, and I've even testet it through phpMyAdmin with perfect result. Secondly, the error message only happens here while I have at least 4 other mysql connections and queries per page. This call to mysql_query() happens at the end of a really long function that handles data for newly created or modified articles. This basically what it does: Collect all the data from article form (title, content, dates, etc..) Validate collected data Connect to database Dynamically build SQL query based on validated article data Send query to database before closing the connection Pretty basic, I know. I did not recognize the username "_securityagent" so after a quick search I came across this from and article at Apple's Developer Connection talking about some random bug: Mac OS X's security infrastructure gets around this problem by running its GUI code as a special user, "_securityagent". Then I tried put a var_dump() on all variables used in the mysql_connect() call, and every time it returns the correct values (where username is not "_securityagent" of course). Thus I'm wondering if anyone has any idea why 'securityagent' is trying to connect to my database - and how I can keep this error from occurring when I call mysql_query(). Update: Here is the exact code I'm using to connect to the database. But a little explanation must follow: The connection error happens at a call to mysql_query() in function X in class_1 class_1 uses class_2 to connect to database class_2 reads a config file with the database connection variables (host, user, pass, db) class_2 connect to the database through the following function: var $SYSTEM_DB_HOST = ""; function connect_db() { // Reads the config file include('system_config.php'); if (!($SYSTEM_DB_HOST == "")) { mysql_connect($SYSTEM_DB_HOST, $SYSTEM_DB_USER, $SYSTEM_DB_PASS); @mysql_select_db($SYSTEM_DB); return true; } else { return false; } }

  Read the article

• .htaccess working on remote server but does not work on localhost. Getting 404 errors on localhost

  - by Afsheen Khosravian

  MY PROBLEM: When I visit localhost the site does not work. It shows some text from the site but it seems the server can not locate any other files. Here is a snippet of the errors from firebug: "NetworkError: 404 Not Found - localhost/css/popup.css" "NetworkError: 404 Not Found - localhost/css/style.css" "NetworkError: 404 Not Found - localhost/css/player.css" "NetworkError: 404 Not Found - localhost/css/ui-lightness/jquery-ui-1.8.11.custom.css" "NetworkError: 404 Not Found - localhost/js/jquery.js" It seems my server is looking for the files in the wrong places. For example, localhost/css/popup.css is actually located at localhost/app/webroot/css/popup.css. I have my site setup on a remote server with the same exact configurations and it works perfectly fine. I am just having this issue trying to run the site on my laptop at localhost. I edited my VirtualHosts file DocumentRoot and to /home/user/public_html/site.com/public/app/webroot/ and this reduces some errors but I feel that this is wrong and sort of hacking it since I didn't use these setting on my production server which works. The last note I want to make is that the website uses dynamic URLs. I dont know if that has anything to do with it. For example, on the production server the URLS are: site.com/#hello/12321. HERES WHAT I AM WORKING WITH: I have a LAMP server setup on my laptop which runs on Ubuntu 11.10. I have enabled mod_rewrite: sudo a2enmod rewrite Then I edited my Virtual Hosts file: <VirtualHost *:80> ServerName localhost DirectoryIndex index.php DocumentRoot /home/user/public_html/site.com/public <Directory /home/user/public_html/site.com/public/> Options Indexes FollowSymLinks MultiViews AllowOverride All Order allow,deny allow from all </Directory> </VirtualHost> Then I restarted apache. My website is using cakePHP. This is the directory structure of the website: "/home/user/public_html/site.com/public" contains: index.php app cake plugins vendors These are my .htaccess files: /home/user/public_html/site.com/public/app/.htaccess: <IfModule mod_rewrite.c> RewriteEngine on RewriteRule ^$ webroot/ [L] RewriteRule (.*) webroot/$1 [L] </IfModule> /home/user/public_html/site.com/public/app/webroot/.htaccess: <IfModule mod_rewrite.c> RewriteEngine On RewriteCond %{REQUEST_FILENAME} !-d RewriteCond %{REQUEST_FILENAME} !-f RewriteRule ^(.*)$ index.php?url=$1 [QSA,L] </IfModule>

  Read the article

• SQL server 2008 R2 installation error

  - by Sonia

  I have a windows 7,32 bit laptop. I am the administrator with all permissions. when I click on the SQL server 2008R2 set up file,it says : "SQL server set up has encountered the following error:Failed to retreive data for this request" click on OK. I have uninstalled all the components of SQL from control panel. I used Windows installer clean up to remove the files(which I must have not done ),but still no go. The summary.txt log says: Overall summary: Final result: Failed: see details below Exit code (Decimal): 847168662 Exit facility code: 638 Exit error code: 50326 Exit message: Failed to retrieve data for this request. Start time: 2012-05-25 14:59:15 End time: 2012-05-25 15:00:09 Requested action: RunRules Log with failure: C:\Program Files\Microsoft SQL Server\100\Setup Bootstrap\Log\20120525_145905\Detail.txt Exception help link: http%3a%2f%2fgo.microsoft.com%2ffwlink%3fLinkId%3d20476%26ProdName%3dMicrosoft%2bSQL%2bServer%26EvtSrc%3dsetup.rll%26EvtID%3d50000%26ProdVer%3d10.0.5500.0%26EvtType%3d0xEF814B06%400x92D13C14 Machine Properties: Machine name: EWAN-PC Machine processor count: 4 OS version: Windows Vista OS service pack: Service Pack 1 OS region: Australia OS language: English (United States) OS architecture: x86 Process architecture: 32 Bit OS clustered: No Package properties: Description: SQL Server Database Services 2008 SQLProductFamilyCode: {628F8F38-600E-493D-9946-F4178F20A8A9} ProductName: SQL2008 Type: RTM Version: 10 SPLevel: 0 Installation location: c:\385030d65c6ff61fb9\x86\setup\ Installation edition: EXPRESS User Input Settings: ACTION: RunRules CONFIGURATIONFILE: FEATURES: HELP: False INDICATEPROGRESS: False INSTANCENAME: QUIET: False QUIETSIMPLE: False RULES: GLOBALRULES,SqlUnsupportedProductBlocker,PerfMonCounterNotCorruptedCheck,Bids2005InstalledCheck,BlockInstallSxS,AclPermissionsFacet,FacetDomainControllerCheck,SSMS_IsInternetConnected,FacetWOW64PlatformCheck,FacetPowerShellCheck X86: False Configuration file: C:\Program Files\Microsoft SQL Server\100\Setup Bootstrap\Log\20120525_145905\ConfigurationFile.ini Detailed results: Rules with failures: Global rules: There are no scenario-specific rules. Rules report file: The rule result report file is not available. Exception summary: The following is an exception stack listing the exceptions in outermost to innermost order Inner exceptions are being indented Exception type: Microsoft.SqlServer.Management.Sdk.Sfc.EnumeratorException Message: Failed to retrieve data for this request. Data: HelpLink.ProdName = Microsoft SQL Server HelpLink.BaseHelpUrl = http://go.microsoft.com/fwlink HelpLink.LinkId = 20476 DisableWatson = true Stack: at Microsoft.SqlServer.Setup.Chainer.Workflow.PendingActions.InvokeActions(WorkflowObject metaDb, TextWriter loggingStream) at Microsoft.SqlServer.Setup.Chainer.Workflow.ActionEngine.RunActionQueue() at Microsoft.SqlServer.Setup.Chainer.Workflow.Workflow.RunWorkflow(HandleInternalException exceptionHandler) at Microsoft.SqlServer.Chainer.Setup.Setup.RunRequestedWorkflow() at Microsoft.SqlServer.Chainer.Setup.Setup.Run() at Microsoft.SqlServer.Chainer.Setup.Setup.Start() at Microsoft.SqlServer.Chainer.Setup.Setup.Main() Inner exception type: Microsoft.SqlServer.Configuration.Sco.ScoException Message: Attempted to perform an unauthorized operation. Data: WatsonData = HKEY_LOCAL_MACHINE@SOFTWARE\Microsoft\Windows\CurrentVersion\Uninstall\Microsoft SQL Server 10 Stack: at Microsoft.SqlServer.Configuration.Sco.InternalRegistryKey.OpenSubKey(String subkey, RegistryAccess requestedAccess) at Microsoft.SqlServer.Configuration.Sco.SqlRegistryKey.OpenSubKey(String subkey, RegistryAccess requestedAccess) at Microsoft.SqlServer.Discovery.RegistryKeyExistsPropertyValueProvider.GetPropertyValue(Object[] context) at Microsoft.SqlServer.Discovery.DiscoveryEnumObject.GetPropertyValueFromProvider(IPropertyValueProvider propertyValueProvider, String machineName, Object[] context) at Microsoft.SqlServer.Discovery.ObjectInstanceSettings.IsObjectFound(String machineName, String idFilter) at Microsoft.SqlServer.Discovery.Product.FilterObjectSet(ArrayList objects, String idFilter) at Microsoft.SqlServer.Discovery.Product.GetData(EnumResult erParent) at Microsoft.SqlServer.Management.Sdk.Sfc.Environment.GetData() at Microsoft.SqlServer.Management.Sdk.Sfc.Environment.GetData(Request req, Object ci) at Microsoft.SqlServer.Management.Sdk.Sfc.Enumerator.GetData(Object connectionInfo, Request request) at Microsoft.SqlServer.Management.Sdk.Sfc.Enumerator.Process(Object connectionInfo, Request request) Inner exception type: System.UnauthorizedAccessException Message: Attempted to perform an unauthorized operation. Stack: at Microsoft.SqlServer.Configuration.Sco.InternalRegistryKey.OpenSubKey(String subkey, RegistryAccess requestedAccess) Ineed to install SQL server 2008 R2 for one of the company softwares to work. Any immediate help will be greatly appreciated. Thanks Sonia

  Read the article

• Nginx $scheme doesn't always work while using SSL for one specific page

  - by jjiceman

  I read and followed this question in order to configure nginx to force SSL for one page (admin.php for XenForo), and it is working well for a few of the site administrators but is not for myself. I was wondering if anyone has any advice on how to improve this configuration: ... ssl_certificate example.net.crt; ssl_certificate_key example.key; server { listen 80 default; listen 443 ssl; server_name www.example.net example.net; access_log /srv/www/example.net/logs/access.log; error_log /srv/www/example.net/logs/error.log; root /srv/www/example.net/public_html; index index.php index.html; location / { if ( $scheme = https ){ rewrite ^ http://example.net$request_uri? permanent; } try_files $uri $uri/ /index.php?$uri&$args; index index.php index.html; } location ^~ /admin.php { if ( $scheme = http ) { rewrite ^ https://example.net$request_uri? permanent; } try_files $uri /index.php; include fastcgi_params; fastcgi_pass 127.0.0.1:9000; fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name; fastcgi_param HTTPS on; } location ~ \.php$ { try_files $uri /index.php; include fastcgi_params; fastcgi_pass 127.0.0.1:9000; fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name; fastcgi_param HTTPS off; } } ... It seems that the extra information in the location ^~ /admin.php block is unecessary, does anyone know of an easy way to avoid duplicate code? Without it it skips the php block and just returns the php files. Currently it applies https correctly in Firefox when I navigate to admin.php. In Chrome, it downloads the admin.php page. When returning to the non-https website in Firefox, it does not correctly return to http but stays as SSL. Like I said earlier, this only happens for me, the other admins can go back and forth without a problem. Is this an issue on my end that I can fix? And does anyone know of any ways I could reduce duplicate configuration options in the configuration? Thanks in advance!

  Read the article

• Cliq Wireless questions

  - by Nathan Adams

  Heres the deal: I am by no means a Linux expert, even less when it comes to the Android OS but lets see if we can't solve this problem. The problem I am having is that on the Cliq we have a broadcom chip. In order to use the wireless card you must first insert the module into the kernel. Fine: # insmod /system/lib/dhd.ko insmod /system/lib/dhd.ko # lsmod lsmod dhd 164936 0 - Live 0xbf000000 # BUT netcfg (or ifconfig in busybox) does not recognize that there is a wireless adapter there: # netcfg netcfg lo UP 127.0.0.1 255.0.0.0 0x00000049 dummy0 DOWN 0.0.0.0 0.0.0.0 0x00000082 rmnet0 UP 14.67.164.2 255.255.255.252 0x00001043 rmnet1 DOWN 0.0.0.0 0.0.0.0 0x00001002 rmnet2 DOWN 0.0.0.0 0.0.0.0 0x00001002 usb0 DOWN 0.0.0.0 0.0.0.0 0x00001002 # busybox ifconfig busybox ifconfig lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:282 errors:0 dropped:0 overruns:0 frame:0 TX packets:282 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:18754 (18.3 KiB) TX bytes:18754 (18.3 KiB) rmnet0 Link encap:Ethernet HWaddr EE:83:E8:B4:4A:ED inet addr:14.x.x.x Bcast:14.67.164.3 Mask:255.255.255.252 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:7148 errors:0 dropped:0 overruns:0 frame:0 TX packets:7659 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2609236 (2.4 MiB) TX bytes:908575 (887.2 KiB) # For giggles if we attempt to launch wpa_supplicant anyways we get this: # wpa_supplicant -Dwext -ieth0 -c/data/misc/wifi/wpa_supplicant.conf wpa_supplicant -Dwext -ieth0 -c/data/misc/wifi/wpa_supplicant.conf ioctl[SIOCSIWPMKSA]: No such device ioctl[SIOCSIWMODE]: No such device Could not configure driver to use managed mode ioctl[SIOCGIFFLAGS]: No such device Could not set interface 'eth0' UP ioctl[SIOCGIWRANGE]: No such device ioctl[SIOCGIFINDEX]: No such device CTRL-EVENT-STATE-CHANGE id=-1 state=0 ioctl[SIOCSIWENCODEEXT]: No such device ioctl[SIOCSIWENCODE]: No such device ioctl[SIOCSIWENCODEEXT]: No such device ioctl[SIOCSIWENCODE]: No such device ioctl[SIOCSIWENCODEEXT]: No such device ioctl[SIOCSIWENCODE]: No such device ioctl[SIOCSIWENCODEEXT]: No such device ioctl[SIOCSIWENCODE]: No such device ioctl[SIOCSIWAUTH]: No such device WEXT auth param 7 value 0x0 - Failed to disable WPA in the driver. ioctl[SIOCSIWAUTH]: No such device WEXT auth param 5 value 0x0 - ioctl[SIOCSIWAUTH]: No such device WEXT auth param 4 value 0x0 - ioctl[SIOCSIWAP]: No such device ioctl[SIOCGIFFLAGS]: No such device # In dmesg we get: <4>[18300.494065] dhd_oob_enable_intr : enable <4>[18305.019976] dhd_net_start failed bus is not ready <4>[18305.020278] dhdsdio_probe: dhd_net_start failed! Do I need to specify the firmware with insmod? Why are we trying to control the interface manually instead of through the Android API? The Android API doesn't support ad-hoc connections as far as I can tell. The card, I am sure, most certainly can.

  Read the article

• What are some fast methods for navigating to frequently used folders in Windows 7?

  - by fostandy

  (This is a followup question from my previous question.) In windows XP I used to be able to quickly navigate to frequently used folders by making use of the 'Favorites' menu item and the hotkey behaviour. In certain conditions it could be set up so that getting to a particular folder was as easy as alt-a x (and without a file explorer window open it was as fast as win-e alt-a x). I am struggling to get anywhere near this speed in Windows 7 and would like to solicit advice from others regarding fast folder navigation to see if I am missing any methods. My current way to navigate quickly is basically move hand to mouse move cursor to navigation pane/pain. scroll all the way to the top (because normally I the panel is focused on whatever deep directory structure I am already in). sift through my 50+ favorites to get the one I want, or click a link to a folder that contains further links in some sort of 'pseudo-tree' functionality. select it. This is slower than my previous method by upwards of an order of magnitude. There are a couple of things I've contemplated: add expandable folders, not just direct links, to the favorites menu. add expandable folders, not just direct links, to the start menu. add links of my favorite folders to a submenu of the start menu so that they come up when I search them. They do but this still rather cumbersome started using 7stacks - url here (I cannot link the url directly due to lack of reputation but http://www.alastria.com/index.php?p=software-7s). This is about the closest I've gotten to some sort of compact, customizeable, easy to access, tree based navigation structure. How do you power users quickly navigate to your favorite folders? Are there keyboard shortcuts I am missing? Can someone recommend other apps or addon or extensions that can achieve this sort of functionality? The Current solution (thanks to the answers below) I am going to use is a combination of Autohotkey and 7stacks - autohotkey to launch 7stacks, 7stacks with the 'menu' stack type for fast, key-enabled navigation to folders organised in a tree structure. This solves about 90% of the issue, the only issues are (note that these are really minor, I am really splitting hairs more than anything here) Can't use this for existing folder navigation (ie already have a explorer window open, want to go to another directory) A bit more cumbersome to add/remove entries to compared to xp favorites. A little slower than xp favorites. Whatever. I'm happy. Thanks guys. I think the answer is a split to John T and Kelbizzle - I've elected to give the answer to John T and +1 to Kelbizzle as I had already mentioned 7stacks.

  Read the article

• How Do I Restrict Repository Access via WebSVN?

  - by kaybenleroll

  I have multiple subversion repositories which are served up through Apache 2.2 and WebDAV. They are all located in a central place, and I used this debian-administration.org article as the basis (I dropped the use of the database authentication for a simple htpasswd file though). Since then, I have also started using WebSVN. My issue is that not all users on the system should be able to access the different repositories, and the default setup of WebSVN is to allow anyone who can authenticate. According to the WebSVN documentation, the best way around this is to use subversion's path access system, so I looked to create this, using the AuthzSVNAccessFile directive. When I do this though, I keep getting "403 Forbidden" messages. My files look like the following: I have default policy settings in a file: <Location /svn/> DAV svn SVNParentPath /var/lib/svn/repository Order deny,allow Deny from all </Location> Each repository gets a policy file like below: <Location /svn/sysadmin/> Include /var/lib/svn/conf/default_auth.conf AuthName "Repository for sysadmin" require user joebloggs jimsmith mickmurphy </Location> The default_auth.conf file contains this: SVNParentPath /var/lib/svn/repository AuthType basic AuthUserFile /var/lib/svn/conf/.dav_svn.passwd AuthzSVNAccessFile /var/lib/svn/conf/svnaccess.conf I am not fully sure why I need the second SVNParentPath in default_auth.conf, but I just added that today as I was getting error messages as a result of adding the AuthzSVNAccessFile directive. With a totally permissive access file [/] joebloggs = rw the system worked fine (and was essentially unchanged), but as I soon as I start trying to add any kind of restrictions such as [sysadmin:/] joebloggs = rw instead, I get the 'Permission denied' errors again. The log file entries are: [Thu May 28 10:40:17 2009] [error] [client 89.100.219.180] Access denied: 'joebloggs' GET websvn:/ [Thu May 28 10:40:20 2009] [error] [client 89.100.219.180] Access denied: 'joebloggs' GET svn:/sysadmin What do I need to do to get this to work? Have configured apache wrong, or is my understanding of the svnaccess.conf file incorrect? If I am going about this the wrong way, I have no particular attachment to my overall approach, so feel free to offer alternatives as well. UPDATE (20090528-1600): I attempted to implement this answer, but I still cannot get it to work properly. I know most of the configuration is correct, as I have added [/] joebloggs = rw at the start and 'joebloggs' then has all the correct access. When I try to go repository-specific though, doing something like [/] joebloggs = rw [sysadmin:/] mickmurphy = rw then I got a permission denied error for mickmurphy (joebloggs still works), with an error similar to what I already had previously [Thu May 28 10:40:20 2009] [error] [client 89.100.219.180] Access denied: 'mickmurphy' GET svn:/sysadmin Also, I forgot to explain previously that all my repositories are underneath /var/lib/svn/repository UPDATE (20090529-1245): Still no luck getting this to work, but all the signs seem to be pointing to the issue being with path-access control in subversion not working properly. My assumption is that I have not conf

  Read the article

• varnish3, mod_geoip with apache2 using mod_rewrite and mod_rpaf

  - by mursalat

  I am maintaining a website with 3 different versions of the site, with 3 different languages, handles with a single system written in php, which takes in environment variables based on the domain name that is being accessed. These are the three sites: myshop.com : english international version myshop.eu : european version of site myshop.ru : russian version of the site when myshop.com is accessed from russia it is to be redirected to myshop.ru, and any country from europe accesses myshop.com, is redirected to myshop.eu, and international visitors stay at myshop.com, although they can go to the country specific site. All these redirections for the country is done using GeoIP apache2 mod in order to determine the country code, which is used in a RewriteCondition to state a RewriteRule, there are some exceptions of IPs that do not do the rewrite for, basically the IPs of the developer's PCs. The site has been doing just fine, until we decided to setup varnish to give the site a boost, it really did give it a great boost, but the country specific rewrites has become buggy. What started to happen is that a russian visitor can go to myshop.com and won't be redirected, until he clicks a random link (perhaps a link not cached by varnish yet) and the user is redirected to their specific country. For that i setup mod_rpaf, and for exceptions to the rewrite rule (for the developer's ip), i used this RewriteCond %{HTTP:X-FORWARDED-FOR} !^43\.43\.43\.43, and i restarted varnish and apache2, it worked for a while, then it messed up again. And whole day i have been doing changes however i have little no clue as to what's going on, sometimes it works, and sometimes it doesn't, and sometimes it half works, etc... As for geoip, i used a php to check the $_SERVER variable, and here is the general idea of the output [HTTP_X_FORWARDED_FOR] => 43.43.43.44 [HTTP_X_VARNISH] => 1705675599 [SERVER_ADDR] => 127.0.0.1 [SERVER_PORT] => 80 [REMOTE_ADDR] => 43.43.43.44 [GEOIP_ADDR] => 43.43.43.44 [GEOIP_CONTINENT_CODE] => EU [GEOIP_COUNTRY_CODE] => FR [GEOIP_COUNTRY_NAME] => France Now, thanks to the "random" redirects, i hardly have a clue as to what is going on, so can you guys please give me some ideas as to what tools to use to debug this? I have tried to see the redirect logs, but they really dont show much, and varnishlog isn't helping much either - although i must admit i am no professional at varnish. I believe the problem is with varnish trying to cache the url, and thus apache redirects are not being done properly, however visits the site first has a redirect, and based on that other users are served the content, depending on from where the user was when the cache was last updated, is it correct? if so, how can i solve the problem? Also, i have the option of using geoip redirects on varnish3 instead of using apache2 to do the redirects, is that what the best practice is? Any suggestion as to debugging this or to fix this would be helpful! thnx!

  Read the article

• Installing ImageMagick on Mac OSX 10.6

  - by Russell C.

  I just got a new Mac and am trying to setup a local Perl development environment. I'm using MAMP but also need the ImageMagick perl module installed in order to do some of the photo processing our scripts require. I tried installing ImageMagick manually but ran into some issues and after reading online a lot of people reported having issues going this route. The general consensus was to install it using MacPorts instead so I went ahead and installed MacPorts. Unfortunately, MacPorts can't seem to install it successfully either. Here is the command I'm using to try to install ImageMagick: sudo port install p5-perlmagick And here are all the errors reported during install: ---> Computing dependencies for p5-perlmagick ---> Building p5-perlmagick Error: Target org.macports.build returned: shell command " cd "/opt/local/var/macports/build/_opt_local_var_macports_sources_rsync.macports.org_release_ports_perl_p5-perlmagick/work/PerlMagick-6.32" && /usr/bin/make -j2 all " returned error 2 Command output: Magick.xs:10918: error: 'struct Methods' has no member named 'exception' Magick.xs:10918: error: request for member 'severity' in something not a structure or union Magick.xs:10918: error: 'ErrorException' undeclared (first use in this function) Magick.xs:10919: error: 'struct Methods' has no member named 'exception' Magick.xs:10920: warning: implicit declaration of function 'GetImageException' Magick.xs:10922: error: 'struct PackageInfo' has no member named 'image_info' Magick.xs:10922: error: 'struct Methods' has no member named 'adjoin' Magick.xs:10929: error: request for member 'severity' in something not a structure or union Magick.xs:10929: error: 'UndefinedException' undeclared (first use in this function) Magick.xs:10929: error: request for member 'severity' in something not a structure or union Magick.xs:10929: error: request for member 'reason' in something not a structure or union Magick.xs:10929: error: request for member 'severity' in something not a structure or union Magick.xs:10929: error: request for member 'reason' in something not a structure or union Magick.xs:10929: warning: pointer/integer type mismatch in conditional expression Magick.xs:10929: error: request for member 'description' in something not a structure or union Magick.xs:10929: error: request for member 'description' in something not a structure or union Magick.xs:10929: error: request for member 'severity' in something not a structure or union Magick.xs:10929: error: request for member 'description' in something not a structure or union Magick.xs:10929: warning: pointer/integer type mismatch in conditional expression Magick.xs:10929: error: request for member 'description' in something not a structure or union Magick.xs:10929: warning: passing argument 2 of 'Perl_sv_catpv' from incompatible pointer type Magick.xs:10929: warning: unused variable 'message' Magick.xs:10856: warning: unused variable 'filename' Magick.c:10784: warning: unused variable 'ref' Magick.c:10777: warning: unused variable 'ix' Magick.xs: In function 'boot_Image__Magick': Magick.xs:2122: warning: implicit declaration of function 'InitializeMagick' Magick.xs:2123: warning: implicit declaration of function 'SetWarningHandler' Magick.xs:2124: warning: implicit declaration of function 'SetErrorHandler' make: *** [Magick.o] Error 1 Error: Status 1 encountered during processing. Before reporting a bug, first run the command again with the -d flag to get complete output. I have no idea what the problem might be or how to go about successfully installing ImageMagick. I'd appreciate any help & advice that someone out there that has done this successfully might be able to provide. Thanks in advance!

  Read the article

• Stack-based keyboard delay using Logitech MX3100 keyboard

  - by Mark S. Rasmussen

  I've been using a Logitech Cordless Desktop MX3100 keyboard for quite a while. I've never really had any problems, except for the occasional typo. I noticed however that I tended make the typo "Laod" instead of "Load", quite a bit more often than any other typos. As it started to get on my nerves, I decided to do some testing. What I found out was than when I write lowercase "load", I'd never make the typo. All uppercase, or just uppercase L, I'd make the typo quite often. My actual (very scientific) testing is probably best described by showing the output: moatmoatmoat MoatMoatMoat loatloatloat LaotLaotLaot loafloafloaf LaofLaofLaof hoathoathoat HoatHoatHoat hoadhoadhoad HoadHoadHoad lortlortlort LrotLrotLrot What i found out was that whenever shift was depressed, typing an uppercase "L" would induce a significant lag if the next character was an "o", compared to the lag of the any other key: High "o" lag: LoLoLoLoLoLo No "a" lag: LaLaLaLaLaLa No lag for neither "o" nor "a": lolololololo lalalalalala By realizing this I regained a slight bit of sanity as I knew I wasn't coming down with a case of Parkinsons. I was actually typing correctly, the lag just interpreted it wrongly. Now, what really bugs me is that I can't fathom how this is occurring. What I'm actually typing, in physical order, is this: L - o - a - d, and yet, the "a" is output before the "o", even though "o" was pressed before "a". So while the keyboard is processing the "Lo" combo, the "a" gets prioritized and is inserted before the "o" is done processing, resulting in Laod instead of Load. And this only happens when typing "Lo", not when typing lowercase "lo". This problem could stem from the keyboard hardware, the receiver hardware or the keyboard software driver. No matter the fault location however, I can't imagine how this could be implemented as anything but a FIFO queue. A general delay, sure, I could live with that, albeit I'd be irritated. But a lag affecting different keys differently, and even resulting in unpredictable outcome - that just doesn't make any sense. I've solved the problem by just switching to a wired keyboard. I just can't shake it off me though; what kind of bug/error/scenario would result in a case like this? Edit: It's been suggested that I stop drinking Red Bull and stick to water instead. While that may actually help solve the issue, I'm really not looking for a solution as such. I'm more interested in an explanation of how this could happen, as I can't imagine any viable technical solution that could result in this behavior.

  Read the article

< Previous Page | 648 649 650 651 652 653 654 655 656 657 658 659  | Next Page >