Search Results

Search found 20099 results on 804 pages for 'virtual host'.

Page 655/804 | < Previous Page | 651 652 653 654 655 656 657 658 659 660 661 662  | Next Page >

• Debian network bridge configuration - /etc/network/interfaces

  - by Mathias

  I'm running a Lenny Xen dom0 hosting multiple virtual machines in a routed IP setup. To get an additional private subnet, I created the bridge xenbr0 in the dom0 with the following commands: brctl addbr xenbr0 ifconfig xenbr0 10.0.0.1 netmask 255.255.255.0 ifconfig xenbr0 up This works as expected, and domU interfaces are added to the bridge by Xen on VM start. My only problem is: how the heck do i specify this configuration in /etc/network/interfaces that it remains permanent and the bridge is available after a reboot? I tried the following config as found on a lot of tutorials: auto xenbr0 iface xenbr0 inet static address 10.0.0.1 netmask 255.255.255.0 network 10.0.0.0 broadcast 10.0.0.255 bridge_stp no I get 2 different errors, depending on if the bridge already exists or not. If it doesn't exist: root@dom0:~# brctl show bridge name bridge id STP enabled interfaces root@dom0:~# /etc/init.d/networking restart Reconfiguring network interfaces...if-up.d/mountnfs[eth0]: waiting for interface xenbr0 before doing NFS mounts (warning). SIOCSIFADDR: No such device xenbr0: ERROR while getting interface flags: No such device SIOCSIFNETMASK: No such device SIOCSIFBRDADDR: No such device xenbr0: ERROR while getting interface flags: No such device xenbr0: ERROR while getting interface flags: No such device Failed to bring up xenbr0. done. And if it exists: root@dom0:~# brctl show bridge name bridge id STP enabled interfaces xenbr0 8000.000000000000 no root@dom0:~# /etc/init.d/networking restart Reconfiguring network interfaces...if-up.d/mountnfs[eth0]: waiting for interface xenbr0 before doing NFS mounts (warning). RTNETLINK answers: File exists Failed to bring up xenbr0. done. Could anyone point me in the right direction please? The bridge works fine when created manually, i just need the right config file entries. The most tutorials I found add some devices to the bridge in the config, is that maybe the problem why it is not working? I don't have any interfaces I want to add to the bridge on creation as they get added later on VM start... Thanks, Mathias

  Read the article

• My email server is being blocked by Yahoo: TS03 Message permanently deferred.

  - by bilygates

  Hello, My mail server has been getting the following error from Yahoo's mail servers since about a month: postfix/smtp[23791]: host g.mx.mail.yahoo.com[98.137.54.238] refused to talk to me: 421 4.7.1 [TS03] All messages from [my ip] will be permanently deferred; Retrying will NOT succeed. See http:// postmaster.yahoo.com/421-ts03.html I have exchanged about 4 emails with Yahoo's support team. The first three seemed like automated messages, and the 4th told me that there is nothing they can do, but if I change my policies I can send them another email in 6 months. They also told me: However, based on the information you have provided us, we cannot systematically deliver your email to the Inbox at this time. We suggest that you ask your users to set up a filter in Yahoo! Mail to ensure that they get your email messages in their Inbox. The problem is that my email doesn't even get to their Spam folder. The server won't allow any connections. I have never sent spam messages, not even newsletters. I only send emails for my new users so they can activate their account. I've also implemented DKIM and told Yahoo about this. I have checked my configuration with http://www.myiptest.com/staticpages/index.php/DomainKeys-DKIM-SPF-Validator-test and it reports that both SPF and DKIM are set up correctly. What should I do? Basically, I'm losing new users every day. Any help will be appreciated. P.S.: I apologize if this particular question has already been asked. I searched for it but didn't find it.

  Read the article

• How have multiple web servers and IPs on the same physical network

  - by jsigned

  I do web development out of a small office and need to have multiple physical and virtual servers that can be accessed from the internet. I also have a number of devices (computers, laptops, tablets, printers, etc) that need connections as well. I have gotten a subnet of 8 IP's from my ISP and while that is adequate for the web servers its far too small for everything that needs access to the network. My router is an ASUS RT-N16 running DD-WRT. I'm just smart enough about this routing topic to be dangerous, think 2 year old with a magic marker. I would like to keep my internal network NAT'ed on the 192.168.x.x network and route the 68.69.x.x 255.255.255.248 traffic directly to the servers. The physical network consists of the 4 port DD-WRT router and an unmanaged gig switch. I have a fiber connection to the office that works as an Ethernet port. In other words I can plug my laptop directly into it and have access to the internet. There is no login or password and the router is setup to get DHCP from the ISP, and to provide DHCP addresses for the internal network. What I've done so far is google and try different configurations with little success. In the end I decided I didn't even know how to ask the questions needed. My questions are: Is this the best way to configure the network? How do you do it? VLANs? Multiple routers? I've never had to configure a router using anything more than the GUI so if this is command line stuff be gentle.

  Read the article

• java max heap size, how much is too much

  - by brad

  I'm having issues with a JRuby (rails) app running in tomcat. Occasionally page requests can take up to a minute to return (even though the rails logs processed the request in seconds so it's obviously a tomcat issue). I'm wondering what settings are optimal for the java heap size. I know there's no definitive answer, but I thought maybe someone could comment on my setup. I'm on a small EC2 instance which has 1.7g ram. I have the following JAVA_OPTS: -Xmx1536m -Xms256m -XX:MaxPermSize=256m -XX:+CMSClassUnloadingEnabled My first thought is that Xmx is too high. If I only have 1.7gb and I allocated 1.5gb to java, i feel like I'll get a lot of paging. Typically my java process shows (in top) 1.1g res memory and 2g virtual. I also read somewhere that setting the Xms and Xmx to the same size will help as it eliminates time spend on memory allocation. I'm not a java person but I've been tasked with figuring out this problem and I'm trying to find out where to start. Any tips are greatly appreciated!! update I've started analyzing the garbage collection dumps using -XX:+PrintGCDetails When i notice these occasional long load times, the gc logs go nuts. the last one I did (which took 25s to complete) I had gc log lines such as: 1720.267: [GC 1720.267: [DefNew: 27712K->16K(31104K), 0.0068020 secs] 281792K->254096K(444112K), 0.0069440 secs] 1720.294: [GC 1720.294: [DefNew: 27728K->0K(31104K), 0.0343340 secs] 281808K->254080K(444112K), 0.0344910 secs] about 300 of them on a single request!!! Now, I don't totally understand why it's always GC'ng from ~28m down to 0 over and over.

  Read the article

• iptables: allowing incoming for 192.168.1.0/24 allowed incoming for all?

  - by nortally

  The internal side of my ISP router has three devices: ISP router 128.128.43.1 Firewall router 128.128.43.2 Server 128.128.43.3 Behind the Firewall router is a NAT network using 192.168.100.n/24 This question is regarding iptables running on the Server. I wanted to allow access to port 8080 only from the NAT clients behind the Firewall router, so I used this rule -A Firewall-1-INPUT -s 192.168.100.0/24 -m state --state NEW -m tcp -p tcp --dport 8080 -j ACCEPT This worked, but UNEXPECTEDLY ALLOWED GLOBAL ACCESS, which resulted in our JBOSS server getting compromised. I now know that the correct rule is to use the Firewall router's address instead of the internal network, but can anyone explain why the first rule allowed global access? I would have expected it to just fail. Full config, mostly lifted from a RedHat server: *filter :INPUT ACCEPT [0:0] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [0:0] :Firewall-1-INPUT - [0:0] -A INPUT -j Firewall-1-INPUT -A FORWARD -j Firewall-1-INPUT -A Firewall-1-INPUT -i lo -j ACCEPT -A Firewall-1-INPUT -p icmp --icmp-type any -j ACCEPT -A Firewall-1-INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT -A Firewall-1-INPUT -m comment --comment "allow ssh from all" -A Firewall-1-INPUT -m state --state NEW -m tcp -p tcp --dport 22 -j ACCEPT -A Firewall-1-INPUT -m comment --comment "allow https from all" -A Firewall-1-INPUT -m state --state NEW -m tcp -p tcp --dport 443 -j ACCEPT -A Firewall-1-INPUT -m comment --comment "allow JBOSS from Firewall" ### THIS RESULTED IN GLOBAL ACCESS TO PORT 8080 ### -A Firewall-1-INPUT -s 192.168.100.0/24 -m state --state NEW -m tcp -p tcp --dport 8080 -j ACCEPT ### THIS WORKED -A Firewall-1-INPUT -s 128.128.43.2 -m state --state NEW -m tcp -p tcp --dport 8080 -j ACCEPt ### -A Firewall-1-INPUT -j REJECT --reject-with icmp-host-prohibited COMMIT

  Read the article

• Enabling mod_rewrite on Amazon Linux

  - by L. De Leo

  I'm trying to enable mod_rewrite on an Amazon Linux instance. My Directory directives look like this: <Directory /> Order deny,allow Allow from all Options None AllowOverride None </Directory> <Directory "/var/www/vhosts"> Order allow,deny Allow from all Options None AllowOverride All </Directory> And then further down in httpd.conf I have the LoadModule directive: ... other modules... #LoadModule substitute_module modules/mod_substitute.so LoadModule rewrite_module modules/mod_rewrite.so #LoadModule proxy_module modules/mod_proxy.so ... other modules... I have commented out all the Apache modules not needed by Wordpress. Still when I issue http restart and then check the loaded modules with /usr/sbin/httpd -l I get only: [root@foobar]# /usr/sbin/httpd -l Compiled in modules: core.c prefork.c http_core.c mod_so.c Inside the virtual host containing the Wordpress site I have an .htaccess containing: # BEGIN WordPress <IfModule mod_rewrite.c> RewriteEngine On RewriteBase / RewriteRule ^index\.php$ - [L] RewriteCond %{REQUEST_FILENAME} !-f RewriteCond %{REQUEST_FILENAME} !-d RewriteRule . /index.php [L] </IfModule> # END WordPress The .htaccess is owned by apache which is the user apache runs under. The apachectl -t command returns Syntax OK What am I doing wrong? What should I check?

  Read the article

• Apache2 process stuck at 100% cpu, CLOSE_WAIT socket lingering

  - by mmazing

  I've troubleshooted the heck out of this today, and I can't seem to find any information on how to determine what is happening exactly. Basically, on my development server, another developer is causing CLOSE_WAIT connections that eat up one or more apache2 processes for several hours if I don't restart apache2. strace on any of the processes yields no information, only that it was able to attach. mod_proxy is not enabled. KeepAlive is on, KeepAliveTimeout is 15 seconds, MaxKeepAliveRequests is 100. From what I've been reading, this may or may not be an apache issue at all, just that that's how CLOSE_WAIT works (the server is waiting for a FIN packet to close the connection). I just can't believe that a server would be crippled so easily by not receiving a packet from a remote host telling it to close the connection. Especially without any intervention for well over an hour. Any tips? I'm about to pull my hair out. Edit : Also, there are no unusual entries in any apache log files. Edit 2: lsof -i shows only a single CLOSE_WAIT per hanging process. (That's what has been bothering me about this, as most other discussions talk about many CLOSE_WAIT connections, while I only have one per process.) The nature of the code that is running (php) doesn't really lend itself to closing open connections and whatnot. I can run the same code that he is executing with the same session data, and not result in a hanging process.

  Read the article

• Migrate Domain from Server 2008 R2 to Small Business Server 2011

  - by josecortesp

  I'm looking for some advice here, rather than the big how to do it I'm looking for what do to I have this home server, quad core and 4 GB of ram (I really can't afford more right now). With a Windows Serve 2008 R2 With ActiveDirectory and a Hyper-V-Virtual machine with SharePoint, TFS and a couple of more thigs. I have a least 10 remote users, all of them joined a Hamachi VPN (working great by the way). But I want to migrate that to a Small Business Server 2011 Standard. I tried to make a VM to join the domain and then promote that VM, back up it and then format the physical server, boot up the VM, Promote the Phisical and then erase the VM, but I can't do that because of SBS requiring a least 4 GB of ram to install (so I can't give all the 4 GB of physical ram to a VM). I was thinking in using a laptop (All the clients are laptop) as a temporal server, join the domain, promote it, then format the server and install SBS on the server and do all again. I really need some advice. Thanks in advance. BTW, I know that the software I'm using is kindda expensive, and I can't afford more hardware. I have access to MS downloads by a University partnership so I have all this software for free.

  Read the article

• 16TB Volumes and SNMP On Windows

  - by John K

  As volumes larger than 16TB became more common, it was recognized that the 32 bit value used to report disk size and usage within the standard "HOST-RESOURCES" MIB in SNMP was not large enough to report the proper disk size. Net-SNMP seems to have addressed this issue by simply manipulating the value of "AllocationUnits" to maintain a 32 bit value for disk utilization (since total disk size/usage is equal to the 32 bit space value times the allocation unit), to allow for the calculation of a volume larger than 8/16TB. Presuming you don't have any reporting interest in the allocation unit, this seems like a fine solution. https://bugzilla.redhat.com/show_bug.cgi?id=654384 Window's built in SNMP service, however, seems to continue to suffer from this error, simply reporting the modulo of the used/assigned disk space, resulting in inaccurate disk size reporting. Is there a way to enable Windows to correctly report disk usage for volumes over 16TB? We attempted to simply install Net-SNMP 5.5 x64 and disable Windows SNMP service entirely, however this unfortunately did not fix our issue. I've seen people in the Cacti community mention simply scripting out a solution. Unfortunately, we're using Observium for quick and basic systems monitoring. If the issue can't be correct on the Window's side, can Observium be made to report custom MIBs?

  Read the article

• Windows 7 machine, can't connect remotely until after ping

  - by rjohnston

  I have a Windows 7 (Home Premium) machine that doubles as a media centre and subversion server. There's a couple of problems with this setup, when connecting to the server from an XP (SP3) machine: Firstly, the machine won't respond to it's machine name until after it's IP address has been pinged. Here's an example: Microsoft Windows XP [Version 5.1.2600] (C) Copyright 1985-2001 Microsoft Corp. C:\Documents and Settings\Rob>ping damascus Ping request could not find host damascus. Please check the name and try again. C:\Documents and Settings\Rob>ping 192.168.1.17 Pinging 192.168.1.17 with 32 bytes of data: Reply from 192.168.1.17: bytes=32 time=2ms TTL=128 ... Ping statistics for 192.168.1.17: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 1ms, Maximum = 2ms, Average = 1ms C:\Documents and Settings\Rob>ping damascus Pinging damascus [192.168.1.17] with 32 bytes of data: Reply from 192.168.1.17: bytes=32 time<1ms TTL=128 .... Ping statistics for 192.168.1.17: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 0ms, Maximum = 1ms, Average = 0ms C:\Documents and Settings\Rob> Likewise, subversion commands with either the machine name or IP address will fail until the machine's IP address is pinged. Occasionally, the machine won't respond to pings on it's IP address, it'll just come back with "Request timed out". The svn server is VisualSVN, if that helps... Any ideas?

  Read the article

• Bounce backs from web-generated e-mails are missing

  - by JerSchneid

  We use Google Apps to host my company's mail. On our website, we send some e-mails on behalf of our users. In those e-mails we include lines like this: Return-Path: <[email protected]> Sender: <[email protected]> Sending the messages works great (passes SPF tests), but in the case that the message is sent TO an invalid e-mail address, we expect to get a bounce back message sent to "[email protected]". That message never arrives. (If we send an e-mail manually from within the gmail interface to the same bad e-mail, the message does arrive). We used to receive the bounce back messages as expected, but it seems like they are always quietly blocked now (not in spam or anything). Is there a new policy that blocks bounce backs when the "From" does not match the "Return-Path" or something? We would really like to get these bounce-backs to verify the delivery of the messages. Is there any way to prevent them from being blocked?! Thank you!

  Read the article

• Postfix Relay to Office365

  - by woodsbw

  I am trying to setup a Postfix server on a Linux box to relay all mail to our Office365 (Exchange, hosted by Microsoft) mail server, but, I keep getting an error regarding the sending address: BB338140DC1: to= relay=pod51010.outlook.com[157.56.234.118]:587, delay=7.6, delays=0.01/0/2.5/5.1, dsn=5.7.1, status=bounced (host pod51010.outlook.com[157.56.234.118] said: 550 5.7.1 Client does not have permissions to send as this sender (in reply to end of DATA command)) Office 365 requires that the sending address in the MAIL FROM and From: header be the same as the address used to authenticate. I have tried everything I can think of in the config to get this working. My postconf -n: append_dot_mydomain = no biff = no config_directory = /etc/postfix debug_peer_list = 127.0.0.1 inet_interfaces = loopback-only inet_protocols = all mailbox_size_limit = 0 mydestination = xxxxx, localhost.localdomain, localhost myhostname = localhost mynetworks = 127.0.0.0/8 recipient_delimiter = + relay_domains = our.doamin relayhost = [pod51010.outlook.com]:587 sender_canonical_classes = envelope_sender sender_canonical_maps = hash:/etc/postfix/sender_canonical smtp_always_send_ehlo = yes smtp_sasl_auth_enable = yes smtp_sasl_mechanism_filter = login smtp_sasl_password_maps = hash:/etc/postfix/sasl_passwd smtp_sasl_security_options = smtp_tls_CAfile = /etc/postfix/cacert.pem smtp_tls_loglevel = 1 smtp_tls_security_level = may smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache smtpd_banner = $myhostname ESMTP $mail_name (Ubuntu) smtpd_tls_session_cache_database = btree:${data_directory}/smtpd_scache smtpd_use_tls = yes sender_canonical: www-data [email protected] root [email protected] www-data@localhost [email protected] root@localhost [email protected] Also, sasl_passwd is set to the correct credentials (tested them using swaks multiple times.) Authentication works, and sends the message when the from headers are correct (also tested using swaks....which works) The emails are coming from PHP, so I have also tried altering the sendmail path in php.ini to use pass the correct from address via -f So, for some reason, mail coming from www-data and root are not having the from fields rewritten to Office 365's satisfaction, and it won't send the message. Any postfix gurus out there that can help me setup this relay?

  Read the article

• Trying to use a SmartHost with my Exchange 2010 server

  - by Pure.Krome

  Hi folks, I'm trying to use a SmartHost with my Exchange 2010 Server. SmartHost details: Secure SMTPS: securemail.internode.on.net 465 <-- Note: that's port 465 Configure your existing SMTP settings (in your email program) to: use authentication (enter your Internode username and password, enter your username as [email protected]). enable SSL for sending email (SMTPS). So I've added the smart host details to my Org Config -> Hub Transport. I then used PowerShell to add the port:- Set-SendConnector "securemail.internode.on.net" -port 465 I've then added my username/password (as suggested above) to the SmartHost as Basic Authentication (with no TLS). Then I try sending an email and I get the following error message :- 451 4.4.0 Primary target IP address responded with: "421 4.4.2 Connection dropped due to ConnectionReset." So i'm not sure how to continue. I also tried ticking the TLS box but stll I get the same error. If i don't use SMTPS (secure SMTP, on port 465) and use basic SMTP on port 25 with no Authentication, email gets sent. Any ideas? EDIT: Btw, I can telnet to that server on port 465 from my mail server .. just to make sure i'm not getting firewall'd, etc.

  Read the article

• Setting up DNS using VirtualMin/WebMin

  - by Nyxynyx

  I am moving from a cPanel server to one where I've installed VirtualMin. The LAMP stack and the website files have been setup properly and I can access the website by its IP address. Problem: Now its time to point my domain mydomain.com to my new server. After reading many sites describing setting up bind and master zones, I am pretty confused as to what to do, especially coming from a cPanel server where its really simple to set this up. Attempt Tried to register my nameservers ns1.mydomain.com and ns2.mydomain.com at my domain registrar, but I am missing the IPs I need to point these nameservers to. Should I set ns1.mydomain.com to the IP addres of my web server, and not register ns2.mydomain.com? When specifying the DNS for mydomain.com, the first one I've set it to ns1.apadment.com. On the manager/admin page of my webhost provider, I am given the option to create a secondary slave DNS, which I assigned to the IP address of my server. Though I am not sure how the slave DNS will copy the info from my web server? I have assigned this secondary DNS ns.hostprovider.com as the second DNS for mydomain.com I tried creating a Virtual Server under Virtualmin, but it seems to mess up Apache's DocumentRoot for the site by creating and enabling a new vhost file that ends with .conf. I edited the .conf file to point DocumentRoot back to where its supposed to be /var/www/mydomain instead of /user/mydomain.com I believe the next step is to setup the zone. Virtualmin has already created a Master Zone with 8 different addresses (www.mydomain.com, ftp.mydomain.com...). Under Nameservers, there are already 2 records. One is the hostname (random name given by hostprovider, ns12345.ip123-123.net), the other is the secondary slave DNS provided by the host provider. Does having BIND running on my web server makes the server the master DNS? Thank you!

  Read the article

• High latency issue for web service call from amazon aws ec2 to local server

  - by SibzTer

  We have a legacy web application that is running in our data center on premises located in Houston. We have a developed a new .net 4 based web application in order to provide new features to customers. The new web application is hosted in amazon aws ec2 environment (N. Virginia region us-east-1b zone). In order to get seamlessly integrate with the legacy application the new web application makes web service calls to retrieve data. We are seeing an unusually high latency time in the order of 5+ seconds for these web service calls. The exact same web service call returns in less than a second on our local PCs (which makes sense given physical proximity to the actual server). The weird part is that we have developers in California who also have the same milliseconds response time. We are testing the web service response using third party tools such as SoapUI, Google Chrome extensions such as Advanced REST Client, Postman REST Client, etc. As if this wasnt weird enough, we have noticed the same low latency from certain other ec2 instances while testing which are in the same region and availability zone as well. If we experienced the high latency consistently from all the ec2 instances I could understand. But there is something else going on. Comparing the various stats and results between the low latency and high latency ec2 servers do not show any significant differences: ping (constant 40ms), tracert, winmtr, etc. We have instances that are in the VPC as well. So I tried both the public and private IP address of the web service host server and that didnt make a difference either for the above results. We need to resolve this latency issue as this is causing the resulting web pages to load very slowly (almost 15+ seconds which is simply unacceptable). The ec2 instances have Windows Server Datacenter 64 bit. Let me know if there is any other infor I can provide to help diagnose this.

  Read the article

• Portable USB drives hidden pertition - New request

  - by ZXC

  This question was made by Francesco on Jul 29 '11 at 17:14. and the replies were not satisfactory due they not point to an important problem that´s: Why could anyone want to make certain data only accesible for a program but not to the users?. For example: If I want to do a safe distribution of original music for demostration purposes I will need several requisites: 1) The music should be heard using a simple procedure like selecting the name of each song on a playlist of a mediaplayer. 2) The portable media, ussually a portable USB drive, must hide for complete and should make unaccesible the files that contain the audio data to anything but the mediaplayer, that must be in the first partition, the one that is visible. 3) Considering that´s impossible to really hide files in a non-hidden partition, a second hidden partition should be created in the USB drive and the audio data will be stored there. 4) The trick is to read the audio data files stored in the hidden partition with a mediaplayer stored in the visible partition, the media player also should be a complete standalone program and independent from any library of the operating system except of the OS audio system. 5) The hidden partition should have a copy protection scheme that could impede to do copies of the data or create working ISO images of it. I know that this description could not be technically accurate but it has a complete logic from the needs of a music producer against the problem of piracy. The philosophy that surrounds the concept is to transform a virtual object like a digital string of audio in a solid object like the analog vinyl discs are.

  Read the article

• Updating modules on VPS hosted under OpenVZ

  - by tertle

  Been trying to install OpenVPN on a VPS but come into a few problems when trying to start the openvpn server: Service deferred error: IPTablesServiceBase: failed to run iptables-restore [status=1]: ['FATAL: Could not load /lib/modules/2.6.18-028stab070.14/modules.dep: No such file or directory', 'FATAL: Could not load /lib/modules/2.6.18-028stab070.14/modules.dep: No such file or directory', 'iptables-restore: line 46 failed']: internet/base:1175,internet/base:752,internet/process:45,internet/process:306,internet/_baseprocess:48,internet/process:775,internet/_baseprocess:60,svc/pp:116,svc/svcnotify:26,internet/defer:238,internet/defer:307,internet/defer:323,sagent/ipts:105,sagent/ipts:39,util/error:52,util/error:32 service failed to start due to unresolved dependencies: set(['user', 'iptables_openvpn']) service failed to start due to unresolved dependencies: set(['user', 'iptables_openvpn']) service failed to start due to unresolved dependencies: set(['iptables_openvpn']) Anyway so after a bit of playing around and some advice, I found that the Linux kernel and modules don't match on my server. uname -r returns 2.6.18-028stab070.14 and ls /lib/modules returns 2.6.18-028stab070.7 The server is running OpenVZ and my container uses Ubuntu 9.10. So my question is, is it possible for me to update my modules on a VPS and if so how would I do this, or is this something I'll need to try get my host to do? Thanks in advance.

  Read the article

• How to set up multiple DNS servers on an intranet

  - by Brent

  We have an Active Directory network, with a mixture of Windows DNS, linux BIND servers, and want to use OpenDNS as our external DNS provider. I am wondering What is the best way to set up these servers (regarding forwarders, recursion, etc.)? Active Directory is our main internal DNS for our domain, and has 3 redundant servers. DHCP and all our servers use these as their DNS servers. Then we have a legacy AD server from an old network that is still authoritative for a bunch of domains. Finally, we have a couple of Linux Bind servers that are authoritative for a bunch of websites we host. Should our main AD servers point to our legacy AD server, which points to one of our BIND servers, which points to the other BIND server, which finally points out to openDNS? Or should our main AD servers point to all of these directly? - or is there a better option? What happens if a domain is listed in 2 places? Does DNS process the forwarders in order? What about root servers - if I want to use OpenDNS for "everything else", do I just list them as the last forwarders, and delete the root servers from all my DNS servers? How does recursion work - in this scenario, should I be using recursion or not?

  Read the article

• Laptop authentication/logon via accelerometer tilt, flip, and twist

  - by wonsungi

  Looking for another application/technology: A number of years ago, I read about a novel way to authenticate and log on to a laptop. The user simply had to hold the laptop in the air and execute a simple series of tilts and flips to the laptop. By logging accelerometer data, this creates a unique signature for the user. Even if an attacker watched and repeated the exact same motions, the attacker could not replicate the user's movements closely enough. I am looking for information about this technology again, but I can't find anything. It may have been an actual feature on a laptop, or it may have just been a research project. I think I read about it in a magazine like Wired. Does anyone have more information about authentication via unique accelerometer signatures? Here are the closest articles I have been able to find: Knock-based commands for your Linux laptop Shake Well Before Use: Authentication Based on Accelerometer Data[PDF] Inferring Identity using Accelerometers in Television Remote Controls User Evaluation of Lightweight User Authentication with a Single Tri-Axis Accelerometer Identifying Users of Portable Devices from Gait Pattern with Accelerometers[PDF] 3D Signature Biometrics Using Curvature Moments[PDF] MoViSign: A novel authentication mechanism using mobile virtual signatures

  Read the article

• OS X Keeps prompting me for SSH private key passphrase (OS X 10.6.8)

  - by Danny Englander

  I have a private key to ssh into my server and the connection works. In my hosts file I have: Host myhost HostName xxx.xxx.xxx.xx GlobalKnownHostsFile ~/.ssh/known_hosts port 22 User myuser IdentityFile ~/.ssh/mykey_dsa IdentitiesOnly yes .. and then I type ssh myhost Every time I connect, I get the Mac OS X keychain prompt and I tell OS X to remember the passphrase but then when I disconnect from ssh and re-connect, I am prompted to add the passphrase to the keychain again. This is only a recent problem so I suspect and issue with Keychain? To be clear, I can 're-add' to keychain every time and connect but this defats the purpose. The permissions on my dsa key are set at 600 or -rw-------@ I tried repairing disk permissions but that did no good. My Google-foo is also failing me, nothing of use came up. So I am not sure if this an OS X / keychain issue or an SSH issue. update: When I try ssh -vvv myhost, I think it reveals the issue: debug1: Trying private key: /Users/danny/.ssh/mykey_dsa debug1: PEM_read_PrivateKey failed debug1: read PEM private key done: type <unknown> debug3: Not a RSA1 key file /Users/danny/.ssh/mykey_dsa. debug1: read PEM private key done: type DSA Identity added: /Users/danny/.ssh/mykey_dsa (/Users/danny/.ssh/mykey_dsa) debug1: read PEM private key done: type DSA debug3: sign_and_send_pubkey debug2: we sent a publickey packet, wait for reply debug1: Authentication succeeded (publickey). ... and after that I get connected. I think this crux of the matter is: PEM_read_PrivateKey failed

  Read the article

• Postfix relay gives error 450 while it should be 550

  - by dieter-be

  Hi, we use postfix to do relaying. We get several messages like the following in /var/log/mail (slightly edited) Apr 13 13:30:29 linserver postfix/smtpd[1064]: NOQUEUE: reject: RCPT from unknown[$ip]: 450 4.1.1 <[email protected]>: Recipient address rejected: undeliverable address: host domain.be [$ip] said: 550 <[email protected]>: Recipient address rejected: User unknown in virtual mailbox table (in reply to RCPT TO command); from=<[email protected]> to=<[email protected]> proto=ESMTP helo=<BLUESTREAK.domain.local> Now, when the master mail servers gives a 550, claiming that the user does not exist, I want the relay to also give a 550 back. What happens now is that it seems to return a 450, causing clients to keep messages queued, keep trying and only notify users after a certain period has passed. According to what I could find, the soft_bounce could cause this. But we have not enabled this option (and by default it's off according to postfix docs) It might also have something to do with the *_reject_code postconf values. Especially since the log message complains the unknown ip. But as you can see in the postconf output below, smtpd_sender_restrictions and smtpd_client_restrictions are empty. So even if it would try to do any restrictions there, 550 is the "worst" error going on, so that's what I expect to be returned to the client. postconf: http://sprunge.us/JYgB Thanks, Dieter

  Read the article

• Failing to send email on Ubuntu box (Karmic Koala)

  - by user25312

  I have a home network with an XP and Ubuntu (9.10) box. I have created a small test php script for checking that I can send emails from my machine. I am using the same php.ini file with the same [mail settings], yet the file works on my XP box, and fails on the Ubuntu box. I have included the script here, hopefully, someone can spot whats going wrong: <?php // send e-mail to ... $to="[email protected]"; // Your subject $subject="Test Email"; // From //$header="from: test script"; $header='From: host-email-username@hostdomain_here' . "\r\n" . // Your message $message="Hello \r\n"; $message.="This is test\r\n"; $message.="Test again "; // send email $sentmail = mail($to,$subject,$message,$header); // if your email succesfully sent if($sentmail){ echo "Email Has Been Sent ."; } else { echo "Cannot Send Email "; } ?> The emails have been spoofed for obvious reasons, but otherwise, the script is exactly as the one I tested [Edit] I have since installed mailutils package on my Ubuntu box, now the script runs and returns 'Email has been sent'. However, the mail never arrives in my mail inbox (I've waited 1 day so far). Is there something else I need to be looking at?

  Read the article

• Understanding mail failure notices, 554

  - by goran

  I'd like to confirm the meaining of a mail failure notice. Here's the message Hi. This is the qmail-send program at mydomain.com I'm afraid I wasn't able to deliver your message to the following addresses. This is a permanent error; I've given up. Sorry it didn't work out. <[email protected]>: 1.2.3.4 does not like recipient. Remote host said: 554 <[email protected]>: Relay access denied Giving up on 1.2.3.4 The way I understand this is, that 1.2.3.4 is not setup to receive mail for this domain. dig domain.com MX shows ;; ANSWER SECTION: domain.com. 6245 IN MX 10 mail.domain.com. domain.com. 6245 IN MX 20 mx.anotherdomain.com. (1.2.3.4 is mx.anotherdomain.com.). The puzzling part is that I have reports that messages sent from gmail get delivered to this address. P.S. Is this a proper question for serverfault?

  Read the article

• When pointing to new DNS servers is there any chance of E-mails being lost if the old E-mail hosting service is still up?

  - by LaserBeak

  I am changing webhosts and will be using the new hosts mail servers instead of the old ones. I have created all the correctly named mailboxes on the new service but have also not yet cut ties with the old webhost. I am expecting that even if the new DNS values which point to the new hosts DNS servers and respective SOA\zone file with the new MX values have not yet propagated and an E-mail is directed at the old hosts mail servers as per the mx records in the SOA\zone records which the old hosting provider holds, the E-mail would still come through to the mailbox that's on the old host providers mail servers. So I am just trying to reaffirm if I got this right and it's essentially impossible for me to loose an E-mail since it will hit either the old hosts mail servers or the new ones ? Also is it possible to configure the same E-mail account to check and collect mail from different mail servers by entering multiple pop3 addresses ? And if I choose to keep the old web hosts mail hosting services as a backup by specifying the mx records for it with a lower priority in the SOA records hosted by the new webhost, is it possible to have any incoming E-mails sent to both servers by the mail daemon so I have two copies? Or is my only option having the primary mail server forward the E-mail somehow to the old mailserver ?

  Read the article

• Explorer.exe not starting after login on Windows Server 2003 (Terminal Services and console)

  - by Pepperoni Icecream

  When users login to a Windows Server 2003 R2 running Terminal Services they have a blank desktop. Upon inspection, explorer.exe is not running. When I login as administrator, using either RDP or to the console, I am having the same issue. I can pull up the taskman and start explorer.exe manually. I have another Terminal Server setup exactly the same way (same apps, settings, GPO, etc . . .) the only difference is we deployed Symantec Endpoint Client 11.0.5 on Friday. For some reason the working Terminal Server is still on 11.0.4, but the suspect server received the 11.0.5 client upgrade. I checked the eventviewer for any relevant explorer.exe entries to no avail. It seems that if SEP is preventing explorer.exe from starting at login it would do the same for the domain admin starting explorer.exe from the taskman. I disabled the SEP client and services on the server and issued smc -stop and tried logging in again. Still no explorer.exe. So I'm not sure if the client upgrade is relevant but it is worth mentioning since that was the last system change. The 2 servers are members of a NLB group. I took the bad terminal server out of the group until the issue is resolved. Actually stopped the host using NLB manager Any help is appreciated.

  Read the article

< Previous Page | 651 652 653 654 655 656 657 658 659 660 661 662  | Next Page >