Search Results

Search found 40915 results on 1637 pages for 'virtual method'.

Page 657/1637 | < Previous Page | 653 654 655 656 657 658 659 660 661 662 663 664  | Next Page >

• CentOS Failover Cluster - SIOCADDRT: No such process (when adding a loopback)

  - by Steve Rolfe

  I'm trying to configure two web servers for a load balancing server. The load balancing aspect works fine (it sees both server, kills 'em if it needs to, and seems to direct traffic fine). The only issue is with the servers looping: /etc/sysconfig/network-scripts/ifcfg-lo:0 DEVICE=lo:0 IPADDR=<Virtual IP> NETMASK=255.255.255.255 ONBOOT=yes NAME=loopback Everytime I try a "service network restart" I get a SIOCADDRT: No such process when loading the loopback interface. Anyone have an idea what's causing this?

  Read the article

• How can I prevent my domain controller doing forward lookups for remote users?

  - by markmnl

  I have a Windows Server 2003 server in the office. I VPN into the LAN remotely. My VPN has a virtual NIC with the Windows Server as the primary DNS since it is a domain controller. When connected to the VPN and I do an nslookup or simply browse the web the DNS from the VPN provides the DNS answers. I believe this is because it has DNS forwarders, so queries it can't answer are forwarded and then it relays the answer. This is the desired behavior for workstations in the office (they should query their domain controller first); however for remote VPN users this is not desirable. I do not want my remote office's server to answer DNS queries it is not the authority of (which happens to be 192.168.x.x). Is there any way I can configure this?

  Read the article

• Apache2 - setting PERL5LIB via SetEnv under CGI

  - by j0nes

  Hi, my setup is as follows: I have one Apache2 webserver running different vhosts, one vhost is for the production website, the other vhost is for a staging / preview system. Both vhosts have different DocumentRoots and also different (Perl) CGI folders. The used modules for each of these vhosts should be in different directories, so I did the following: <VirtualHost...> ServerName production SetEnv PERL5LIB /home/production/modules </VirtualHost> <VirtualHost...> ServerName staging SetEnv PERL5LIB /home/staging/modules </VirtualHost> However, I just noticed that in my Perl CGI scripts, both paths get filled into my @INC, so I can not separate the staging modules from the production modules, e.g. the SetEnv directive is not limited to a single virtual host, but seems to work globally. How can I solve this? Thanks! Jonas

  Read the article

• port to subdomain

  - by takeshin

  I have installed Hudson using apt-get, and the Hudson server is available on example.com:8080. For example.com I use standard port *:80 and some virtual hosts set up this way: # /etc/apache2/sites-enabled/subdomain.example.com <Virtualhost *:80> ServerName subdomain.example.com ... </Virtualhost> Here is info about Hudson process: /usr/bin/daemon --name=hudson --inherit --env=HUDSON_HOME=/var/lib/hudson --output=/var/log/hudson/hudson.log --pidfile=/var/run/hudson/hudson.pid -- /usr/bin/java -jar /usr/share/hudson/hudson.war --webroot=/var/run/hudson/war 987 ? Sl 1:08 /usr/bin/java -jar /usr/share/hudson/hudson.war --webroot=/var/run/hudson/war How should I forward: http:// example.com:8080 to: http:// hudson.example.com

  Read the article

• Problems switching to QEMU control panel with -nographics

  - by tor

  It seems that the terminal does not recognise CTRL+ALT+2 when typed, so I don't know how to quit the QEMU emulation, or switch to the QEMU control panel. I am running Mac OSX Lion, and I type $ qemu-system-arm -M verdex -pflash flash.img -nographic -sd sdcard.img to start QEMU emulation of an ARM system in the Terminal. I learned from this site that typing CTRL+ALT+2 should work, but the only thing that happens to me, is that a "2" is printed on the command line of the virtual operating system. Any ideas on what could be wrong? Is this a Mac specific issue? (The same problem occurs in both terminal.app and iTerm2)

  Read the article

• Error installing Arch Linux

  - by Garethj94

  So, I am trying to install Arch Linux on my Acer Aspire 4830tg, but I keep running into problems. Some background knowledge, I am trying to install Arch off a usb stick and I got the iso image using bittorrent. I am also trying to install it alongside of Windows 8 (which is already installed). So when I boot into Arch linux I get this error: :: Mounting '/dev/disk/by-label/ARCH_201212' to 'run/archiso/bootmnt' Waiting 30 seconds for device /dev/disk/by-label/ARCH_201212 ... ERROR: '/dev/disk/by-label/ARCH_201212' device did not show up after 30 seconds... Falling back to interactive prompt You can try to fix the problem manually, log out when you are finished sh: can't access tty; job control turned off I know that it will work if I run it on a virtual machine but whenever I try to install it on my laptop I keep getting this error. And since you can't register for the Arch forums without a Arch terminal to run their captcha command I can't ask this on their forums.

  Read the article

• ICS as guest in Ubuntu 12.04 host

  - by oshirowanen

  I have installed Android as per this guide as a guess os via VirtualBox: http://www.android-x86.org/documents/virtualboxhowto Using the following ISO: android-x86-4.0-RC1-eeepc.iso But I am unable to connect to the internet from within the android virtual machine. The host OS is Ubuntu 12.04 where the internet works fine. I have internet access via a usb wireless connection to the home router. All this is fine. If I install Ubuntu 12.04 as a guest, where the host is also Ubuntu 12.04. The guest os'es internet works fine out of the box. But for some reason, I can't get the above androids internet to work out of the box as the guest os. Anyone know what I am doing wrong?

  Read the article

• Windows 7 / 8 tool for amplifying sound / equivalent to pavucontrol?

  - by Quandary

  I'm watching live streamed videos, but the volume sometimes is barely loud enough. With Windows, I can only turn the system volume and the flash volume up to maximum, and then bad luck if that's still not loud enough. On Linux, on the same notebook, I have the same problem, but I can use pavucontrol to amplify the sound volume beyond 100%. Unfortunately, I can't always work on Linux, since Visual Studio and SQL-Server only run on Windows. Is there any tool or way to amplify volume on Windows 7 / 8 , without having to resort to run Linux in a virtual machine?

  Read the article

• Can't access VirtualBox host-only network from windows host

  - by Markus Orreilly

  I've got two vms running on a windows host, each with a host-only network and ips in the 192.168.56.XXX range. One of them is running apache and serving some content that I want to access from my windows host. However, the windows host can't access the apache server at all. The server is running on 192.168.56.103. ipconfig from windows says it's ip for the Virtual Box interface is 169.254.143.37. I tried route add to route 192.168.56.XX traffic, but everything I tried didn't work and I was probably using it wrong. Any ideas on how to make this work?

  Read the article

• Hide non VHD partitions

  - by James

  Hey! I have two partition on my HDD: C and D. On D: I have a vhd image (with windows 7 ultimate) that I use to boot from. When I'm running the OS from VHD I can still access my physical parititons. Is it possible to dismount them, in order to see just the virtual disks in the VHD OS? I tried with the physical C and it says that I cannot dismount a boot paritition and I think D cannot be dismounted because the VHD is on it.

  Read the article

• IIS seems to send email twice

  - by David Brunelle

  Hi, we have a request page in our website that send email to confirm the request. It seem that whenever this page is accessed, some (not all of them) are sent more than once at different time, sometime hours apart. The code (which is an old ASP page) looks fine as it sends only once to the recipient. So I doubt it's a programming related problem. When looking at the Exchange server, the tech told me that he seems to be receiving the request twice at different time, so the problem comes from what's between the code and Exchange. My hypothesis is that IIS seem to 'remember' the page and rerun it for some reason. Any hint on where to start? We have IIS 6 (in french if it makes any difference) with Exchange 2007. IIS is running on a Windows Server 2003 machine (virtual machine I believe) in a DMZ. I don't know about Exchange. Thank you.

  Read the article

• does vmware server needs bare metal or can be installed on an existing OS

  - by Registered User

  I am new to virtual stuff on Vmware sort of environment.I am basically testing Vmware and its various things for our needs.I have a linux 64 bit laptop.I want to know 1) The Vmware server can it be installed in this existing OS or I need to have baremetal installation for this? 2) What is the advantage of using Vmware Server on Vmware workstation ? 3) What is the use of ESX server of vmware? I have seen some alternatives like Xen which one is better Xen or Vmware might be a debatable issue but my questions for Xen are also same I checked Citrix website. 1) I see similar products for Xen What is the advantage of using Xen Server on Xen desktop ?

  Read the article

• Manual Duplex printing for Mac (and/or Linux)

  - by chris_l

  My printers don't support automatic duplex printing. I'm looking for a solution for my Mac and Linux computers that I've seen with most Windows printer drivers: Check "Manual duplex" in the printer screen Printer starts printing one side A dialog appears, asking me to flip the pages Printer prints the other side. One thing I can do, is print odd pages, then reopen the dialog and print even pages, but this is very inconvenient, especially when I only want to print a certain page range of the document as the Mac dialog forgets my previous page range every time. It gets even more inconvenient, when printing 2-up double sided, or when changing additional settings for this one printout. Is there maybe some tool, that can do this? Or maybe a "virtual printer driver" that can sit somewhere between the dialog and the actual printer driver, which manages these steps? (The Windows tool http://en.wikipedia.org/wiki/FinePrint can do something like that, but I don't need all of its features - and I need it on Mac/Linux) Thanks, Chris

  Read the article

• Can't login to just installed view administrator

  - by matarvai81

  Hi, we are starting to test View for our purposes. I have created new test enviroment, new vdidemo active directory, new virtual center etc... I just installed view connection server component to new server and trying to do initial configuration, but when trying to log in I get following error " Error accessing the View Administrator. Contact the system administrator" Log file says following error 08:14:08,925 INFO LoginBean User administrator has failed to authenticate to View Administrator What is causing this problem? How can I log in and start to test VDI?

  Read the article

• VPN Network intermittantly fails to provide internet: What could be possible causes

  - by Jake M

  We have a small office with our own VPN setup. We occasionally experience failures in our internet connection where we cannot access the internet. Most of the time the internet connection will resume by itself(without me doing anything) after a period of time(10 mins). Would you be able to suggest possible causes of the connection failure so I can then go and run some tests? Our network architecture is like so: A 'Billion' brand router that is connected to the internet via phone cable and then connected to our Cisco Switch A Cisco Switch/Bus which is connected to all our office nodes, our external harddrive and also to our router as stated above. All connections are via ethernet cable A series of work computers(nodes) connected via ethernet cable to the Cisco switch. Our ISP is TPG Australia We have a Virtual Private Network All the ethernet cables are about 3 years old Do you think that the causes of our intermittant connection problems could be due to the following: Data collisions in the ethernet cables Old/Faulty ethernet cables Our ISP has bad service Can you think of any other causes of the problem?

  Read the article

• Apache, Django with mod_wsgi, and large request buffering

  - by Mukul

  In my setup of Apache 2.2 MPM worker and Django 1.3 with mod_wsgi 2.8, I need to support large POST request payloads. The problem is that when there are many such simultaneous requests, Apache uses up all the memory in the system and then crashes. It seems that Apache is buffering the requests completely in memory before executing the WSGI handler and passing it the request. Is there any way to control request buffering in Apache? The log shows the following error whenever the crash happens: [Wed Jun 29 18:35:27 2011] [error] cgid daemon process died, restarting Here's my virtual host's configuration: <VirtualHost *:8080> ServerName example.com ErrorLog /var/log/apache2/error.log WSGIScriptAlias / <path to django.wsgi> WSGIPassAuthorization on WSGIDaemonProcess example.com WSGIProcessGroup example.com XSendFileAllowAbove on XSendFile on </VirtualHost>

  Read the article

• Cannot access Application configured on local IIS 7 using IP/machine name

  - by SilverHorse

  I have a windows 7 machine 64 bit and IIS 7 I have a default website on the IIS.Its binding is {IP: All Unassigned , Port:80 , Host Name : blank} I have added a new asp.net application to that website,mapped physical path, have set the virtual path as "MyWebApp". Application pool for "MyWebApp" is "DefaultAppPool" {.Net Framework: 4.0 ; Managed Pipeline Mode: Classic} The problem I am facing is I can access the website using http://localhost, http://IP.IP.IP.IP and http://MyMachineName But I can not access the Application other than using http://localhost/MyWebApp What should I do if I want to access the webapp using http://MyMachineName/MyWebApp OR http://IP.IP.IP.IP/MyWebApp Please note : I have already created an inbound rule to allow all HTTP traffic for port 80 in firewall settings.

  Read the article

• WebDAV "PROPFIND" exception in IIS due to network share?

  - by jacko

  Hi all, We're finding continuous exceptions in our event viewer on our live box to the following exception: [snippet] Process information: Process ID: 3916 Process name: w3wp.exe Account name: NT AUTHORITY\NETWORK SERVICE Exception information: Exception type: HttpException Exception message: Path 'PROPFIND' is forbidden. Thread information: Thread ID: 14 Thread account name: OURDOMAIN\Account Is impersonating: True Stack trace: at System.Web.HttpMethodNotAllowedHandler.ProcessRequest(HttpContext context) at System.Web.HttpApplication.CallHandlerExecutionStep.System.Web.HttpApplication.IExecutionStep.Execute() at System.Web.HttpApplication.ExecuteStep(IExecutionStep step, Boolean& completedSynchronously) Other Specs: Windows Server 2003 R2 & IIS 6.0 We've narrowed it down to occuring when people try to access shares on the box from within the network, and have discovered (we think) that its due to the WebDAV web services extension being previously disabled by past staff. The exceptions are being thrown when trying to access directories that are virtual dirs in IIS, and plain old UNC network shares What the implications for enabling the WebDAV extensions on our live web server? And will this solve our problems with the exceptions in our event log?

  Read the article

• Can not change to a static IP in Fedora 19

  - by user196272

  Im having a bit of a weird situation. Ive installed Fedora Linux 19 onto a virtual machine with no GUI. initially eth0 does not show up when I perform ifconfig. when I run dmesg | grep eth I see the adapter but it says it changed names to p2p1. Once I perform the ifconfig p2p1 up command it shows up. Now when I try to edit the /etc/sysconfig/network-scripts/ifcfg-p2p1, it does not exist. the only scripts that are there lo and enp0s3. If I try to create the ifcfg-p2p1 file with the correct settings, I can not restart the network service. I tried editing the enp0s3 file, but that did not work. Im fairly new to linux and not sure what else to put in here, so if you need any more information just let me know and Ill put it in here.

  Read the article

• Raid HDD Boot up

  - by user234695

  My server is Power Edge 1950 running server 2008 32Bit, using 3 Physical SAS HDD as a Virtual 2 Disk configured for RAID5, with partition of C drive as OS and D drive as Data. Planning to format and install Server 2008 R2 64Bit so I insert a New Physical disk and configured as RAID5 and clone the C drive and D drive to the new hard disk. Now I need to test that the new hard disk is able to boot windows and work as expected. How do I test, I am not able to boot the windows by choosing the new harddisk, the bios show only the existing HDD, not the new one. Also, if I remove the old three hard disk, and leave the new harddisk and then am I able to boot the device, if I do this does my existing RAID5 configuration and data on the hard disk still remain.

  Read the article

• How to open existing VMs in VirtualBox?

  - by Alex R

  VirtualBox seems to lack the obvious "File - Open" menu option. Frustrating! More details... I recently got a new workstation and I moved my VirtualBox and VMWare Player VMs from the old PC to the new. The VMWare Player VMs are a snap... you go to "File - Open a Virtual Machine...", find the .vmx files from the old PC, and voila! It's up and running. All the required files apparently are in the same folder. With VirtualBox there just doesn't seem to be a way to do that. Looks like VMs are tied to the original host in some magical/invisible way like registry entries, etc.

  Read the article

• Error adding 4tb LUN (Raw Device Mapping) to ESX4 VM

  - by Tom Gardiner

  Hi guys, I'm trying to map an existing 4tb LUN from a Fibre Channel SAN, through to a VM in my ESX4 environment. It keeps telling me that the VMDK file size exceeds the the maximum size supported by the datastore. I've tried in Physical compatibility mode, and also both Virtual styles. I'm a little confused by this as we had the same LUN mapped through to another VM when we were running ESX3.5... I've also noticed that some of my other RAW mappings are generating extremely large VMDK files on the ESX servers. Does anyone know if this change in behaviour is intentional? And if so why? It doesn't seem to me that if the LUN is mapped directly to the VM that it's size should be relevant. We're running 4.0.0 build 236512, and 4.0.0 build 219382 and I've not had any success on either. Any insight or advice would be much appreciated! TG

  Read the article

• Connecting Small business network to Azure Site to Site VPN

  - by MarkKGreenway

  Would like to have connectivity between azure virtual machines and on LAN users. My current network has a Cisco ISA550 connected to the WAN (one Ethernet cable into the office the fiber transceiver is on a different floor)and any public servers can be one-to one NAT-ed to have a public and private IP. What is the best way to get a reliable connection. Between end users and the cloud? I want to know the preferred on site endpoint. Do the azure vm's have to have a local ip in the LAN subnet? (Right now 10.10.0.0/20 or 255.255.240.0 to give room if this is the case). If in purchased an asa550 would I put it behind or in front of the isa550. Would it be ahead or peer with the users switches? What is the best way to get a reliable connection. Between end users and the cloud servers?

  Read the article

• Troubleshooting source of heavy resource-usage on a windows server 2008 running multiple sites

  - by batman_man

  Hi, I am running about 10 asp.net websites on a hosted virtual server. The server runs Server 2008 - each website is backed by its own database running on SQL server 2008 on the same box. Lately the box has seemed really slow. The only kind of discovery i could think of doing was looking in the task manager, where i can see w3wp and sqlserver.exe jumping to 40% cpu usage every 5-10 seconds. What are the steps i can take to determine which of my websites is taking these resources and or what database is getting hit the most? I have of course ssms installed on the machine as well. As you can tell, my sysadmin skills are very very limited - any help would be much appreciated.

  Read the article

• What's the best way of handling permissions for apache2's user www-data in /var/www ?

  - by gyaresu

  Has anyone got a nice solution for handling files in /var/www/ ? We're running Name Based Virtual Hosts and the apache2 user is 'www-data' We've got two regular users & root. So when messing with files in /var/www ,rather than having to... chown -R www-data:www-data ...all the time, what's a good way of handling this? Supplementary question. How hardcore do you then go on permissions? This one has always been a problem in collaborative development environments. Cheers.

  Read the article

< Previous Page | 653 654 655 656 657 658 659 660 661 662 663 664  | Next Page >