Search Results

Search found 19768 results on 791 pages for 'hardware programming'.

Page 667/791 | < Previous Page | 663 664 665 666 667 668 669 670 671 672 673 674  | Next Page >

• Wifi Drops Connections with WPA2-PSK

  - by graf_ignotiev

  I run a small computer lab made up of 10 computers of identical hardware and software (Dell Latitudes with Windows 7 x64 Enterprise) and I use a ZyWALL 2WG as a router/firewall. Nine of the computers connect to the router over wifi using WPA2-PSK encryption while the last one is connected by ethernet cable. I'm having a problem where any computer connected to the wi-fi occasionally drops off the network (it cannot be pinged and the client cannot ping the gateway). It only happens on the wifi side and only when the encryption is WPA2-PSK or WPA-PSK. I tried using another router with a different make and model and had no problems. Thinking it could be a software error, I reset the router to factory defaults and installed the newest firmware (V4.04(AQI.8) | 04/09/2010), but still have the problem. The 802.1X log gives the following error User logout because of user disassociation. with this note WPA2-PSK:00242c582ece:logout where 00242c582ece is the mac address of the device. At this point I'm out of things to try and leads to follow. It looks like this user had the same or similar problem, but none of those proposed solutions work for me.

  Read the article

• Migrate Windows Server 2008 to a new hard disk 2

  - by MainMa

  Hi, A few weeks ago, I already asked how to move a Windows Server 2008 to a new hard disk. Despite the previous answers and two weeks lost trying to do it, I am always unable to move the OS to the new drive. What I tried: A backup/restore using Windows Backup. This never helped. First, I tried to backup, then copy the backup to a new drive, then restore. This results in "The parameter is incorrect. (0x80070057)" error caused by a bug in Windows Backup. Recently, I attempted to backup to a network share, but I can't restore from it, because of a "*The network path was not found. (0x80070035)" error. Trying the netsh interface ipv4 set address [...] does not work neither (saw at least three different errors, mostly "The interface is unknown.") A previously suggested solution using imagex from Windows AIK results in a non-bootable disk after writing an image to it. When booting from Windows 2008 installation disk (from USB), it finds that the HDD is not bootable and proposes to fix this, but then crashes, resulting in an unbootable USB flash disk (and HDD stays unbootable). As I said in my previous question, doing a clone of a hard disk drive gives an (of course) bootable disk, but Windows complain about hardware changes and cannot start. Now can somebody suggest me another way to move Windows Server 2008 to a new hard disk? Is it at least possible to do, or any hard disk failure/change implements necessarily to reinstall the whole OS?

  Read the article

• How to multiseat with HW 3d accel on CentOS 6.3 Final?

  - by user35070

  I would like to setup a multiseat configuration on CentOS 6.3 (two video cards, two keyboards, two mice, two monitors) and have hardware accelerated 3D on both monitors. 3D HW acceleration rules out Xephyr. I saw somewhere that recent versions of GDM (3.3 and newer?) don't support multiseat, so do I have to install KDM to make this work? If I just create a duplicate section with new device identifiers in my xorg.conf file, will this 'just work'? Using different ports on the same video card and separate keyboards, mice, and displays, the result was a desktop which spanned both monitors with both keyboards and mice acting as the same input in the GUI. I will power down and put in the new video card and report on the results soon. Both video cards are nvidia. UPDATE after putting in another NVIDIA video card, default behavior (before changing xorg.conf) is that one screen works normally, and both mice and keyboards are connected to it. Changing xorg.conf and the display manager to KDM and following the directions here https://help.ubuntu.com/community/MultiseatX#Ubuntu_10.04_.28Lucid.29 , I have 2 mirrored screens connected to separate video cards, DRI enabled, and 2 mice both connected to the same pointer. Keyboards don't do anything, however, I probably just need to fix a setting in xorg.conf I would still like to get multiseat functionality, eg. separate screens with separate input devices I have verified that the separate X processes are running (see page above) using 'ps aux | grepX [01]'

  Read the article

• Mac Management and Security

  - by Bart Silverstrim

  I was going through some literature on managing OS X laptops and asked someone some questions about usage scenarios when using the MacBooks. I asked someone more knowledgeable than I about whether it was possible for my Mac to be taken over if I were visiting another site for a conference or if I went on a wifi network at a local coffee house with policies from an OS X Server with workgroup manager (either legit for the site or someone running a version of OS X Server on hardware they have hidden somewhere on the network), which apparently could be set up to do things like limit my access to Finder or impose other neat whiz-bang management features. He said that it is indeed possible for it to happen as it would be assigned via the DHCP server and the OS X server would assume my Mac is a guest and could hand out restrictions and apparently my Mac will happily accept them without notifying me or giving me an option, unlike Windows which I believe would need to be joined to a domain before it becomes "managed" by Active Directory. So my question is as network admins and sysadmins with users traveling with MacBooks, is there a way to reasonably protect your users from having their machines hijacked without resorting to just turning off networking all the time? Or isn't this much of a security hazard? What threat does this pose to the road warriors in your businesses?

  Read the article

• ASUS P8B WS - Endless Reboots

  - by tuxGurl

  I am running a Intel XEON 1245 with 4GBx2 Kingston Memory ECC Unbuffered DDR3 on an ASUS P8B WS motherboard. BIOS Version 0904 x64. This system is a little over a month old. It is running Ubuntu 11.10. This evening I found the machine turned off. When I tried to restart it, it would POST and stop at the GRUB screen. When I selected Ubuntu and hit enter within 2-3 seconds the would shutdown and restart. If I stayed at the GRUB screen and did nothing the system would not cut out. I tried booting off a USB stick and again 2-3 seconds after selecting 'Try Ubuntu without Installing' the machine will cut power and reboot. Things I have tried so far: Resetting the BIOS using the on board jumper Resetting the BIOS settings to default Disconnecting all external hardware - except keyboard & monitor Booting with 1 stick of RAM - I tried different single sticks Ensured that onboard EPU and GPU boost switches are in the off position. I am running a Memtest86 right now and it has been running for 38+ minutes. This is not an OS problem or an overheating issue (I have a CoolerMaster HAF Case with 3 fans besides the CPU fan) I am at a loss as to what to try next. I think the BIOS is mis-configured somehow but I don't know what to look for.

  Read the article

• VMware vSphere Hypervisor 5 with Intel SPL 5000 in Raid 0 no boot from DVD?

  - by Richard

  I hope this is the correct StackExchange, since I am only using StackOverflow for Web development, but need some help with my server configuration. I would like to install VMware vSphere Hypervisor 5 on my server here at home and run a view machines on it such as Windows Server 2008 and Red Hat. I used to have either OpenSuse or Windows Server 2008 installed but I would like to get into VMWare Hypervisor. My hardware configuration: - Intel S5000PSL with bios version S5000.86B.10.60.0091 build date 10/09/2008 as of read out of bios - E5420 @ 2.5GHz Intel Xeon CPU The Intel Virtualization Technology is enabled in the BIOS - DVD DH20A4P DVD Writer - 8GB ECC Ram I have configured a RAID 0 on my 2 WD 2TB SATA drives I have burned the Hypervisor 5 on an empty DVD and it is bootable, I tested it on my client PC. The main problem here is basically, that I cannot boot the DVD on my server. I have set the Boot Option to the DVD drive. I have booted from the BIOS straight in the DVD drive and it does not work. I do not see any error messages. The only thing I see are the PXE error messages when it tries booting from the network and other devices, obviously without any result. Does anybody know why I cannot boot the DVD? What could cause the problem? I have sucessfully installed Windows Server 2008 via original DVD about 1 year ago, so the DVD drive can read and does work. The DVD drive is available in the BIOS and I have checked all cables and none of them is loose in any way. I even see the light flashing but it does not want to boot from the DVD. I am looking forward to suggestions and things that I should check. Thank you very much

  Read the article

• RTL8192SU Linux Issue Installing Driver

  - by s32ialx

  OK I've read tons of fourms of people getting the onboard RTL8192SE working and the RTL8192SU working dif is U = USB they are both N and i have both Toshiba L500D-00T pre-installed Win Vistax64-HP and i have obtained the free Win7x64-HP upgrade the onboard wificard sucks and can't hold a stable connection for more then 20minutes in windows but the usb is amazing. Now problem is i tried both Ubuntu and Mandriva with no resolve the issue is the onboard drive detects and actually SHOWS that it's there but no wireless networks detect so it's saying no SSID's are broadcasting which i know is a lie since I'm running a 2wire bell dsl modem with built in wifi and a Linksys wrt54g w/ DD-WRT firmware and both are broadcasting fine. Why don't i use the USB? In the hardware device manager in mandriva it shows up as unknown but shows that it's realtek and that it's a 8192 chipset. but no option to for a driver install and when i do a make in terminal i get this error and no clue what it means [root@John-PC rtl8192se_linux_2.6.0010.1020.2009_64bit]# make make: *** /lib/modules/2.6.31.12-desktop-3mnb/build: No such file or directory. Stop. make: *** [all] Error 2 [root@John-PC rtl8192se_linux_2.6.0010.1020.2009_64bit]# any help appreciated. and just encase I'm running currently Mandriva Spring 2010 Free

  Read the article

• Printer deployment via Group Policy not working on a single system

  - by Aron Rotteveel

  One of my coworkers just got a new laptop running Windows 7 Pro x64. We use a GPO to deploy the printers to every system, but for some reason it is not working on this system. I have been breaking my head over this for the past 3 hours now without any result. The strange thing is that gpresult /H seems to indicate that the GPO did run. The hardware: Laptop: Windows 7 Professional x64 Print server: Windows Server 2008 x64 R1 HP Color LaserJet 2605dn HP LaserJet P2015 Driver packages on server: HP universal printer driver PCL5, both X86 as X64 Oddities and other info: GPO working flawlessly on every other system, including my own Windows 7 Ultimate X64 laptop gpresult /H shows the GPO being ran Windows Firewall completely disabled on the new laptop Below is the output for gpresult /H (in Dutch sadly, but I think you'll recognize it): Beleidsregels Windows-instellingen Printerverbindingen Pad Dominerend groepsbeleidsobject \\Server2008\HP Color LaserJet 2605dn Printers \\Server2008\HP LaserJet P2015 Printers Beheersjablonen Beleidsdefinities (ADMX-bestanden) opgehaald van de lokale computer. Configuratiescherm/Printers Beleid Instelling Dominerend groepsbeleidsobject Beperkingen van point-and-print Uitgeschakeld Printers Like I said, I have been trying to figure this out for the past few hours or so without any result, so you are my last hope. Any help is appreciated.

  Read the article

• Making the iPhone work with stripped down Windows XP

  - by Gabriel

  Hi, this is my first time posting here and I have a really specific question. I have an ASUS eee 901 running Windows XP Home. I had everything working well, but then I decided to improve performance by moving Windows to the smaller but faster internal SSD. I used Nlite to strip down Windows, following the instructions here: http://wiki.eeeuser.com/howto:nlitexp I now have a very lightweight installation of XP home with SP3 and all the current updates. Almost everything is working really well. I have installed iTunes and I CAN sync with no problems. However, each time I plug in my iPhone 3GS (latest firmware), Windows tries and fails to install drivers. The Found New Hardware Wizard launches, but nothing I do will make it complete successfully, with the result that the iphone does not show up in Windows as removable storage, or as a camera. When I launch the Camera and Scanner Wizard, it shows only my webcam, not the iphone. I have verified that I have the following files in place: Windows\System32\ptpusb.dll (regsvr32 successful) Windows\System32\ptpusd.dll (entry point not found, can not be registered) Windows\System32\usbaaplrc.dll (entry point not found, can not be registered) Windows\System32\drivers\usbaapl.sys Windows\System32\drivers\usbscan.sys Windows\System32\drivers\usbstor.sys Does anyone know if some other file is required or if there's some other element preventing this from working? Edit (From posted answer) I did select Cameras & Camcorders, and my webcam is working fine for video & still capture.

  Read the article

• Server taking too long to respond error

  - by DCJones

  This is my first post on serverFault and my first entry in to web server configuration. The hardware and software. CPU: GenuineIntel, Intel(R) Core(TM)2 Duo CPU E7500 @ 2.93GHz OS: Linux 2.6.18-128.el5 Memory: 2Gb Background. I am running a small database (MySQL), around 1000 records with each record containing 44 fields. At the start of each day “00:01” the tables are cleared and populated with fresh data. The are 10 remote PCs all running Winodws XP and Firefox internet browser. All remote PC’s are connected to the internet using a min 4Gb broadband connection. Each remote PC runs a URL which displays a dynamic page of data which is refreshed every 20 seconds. This is a continual process 24 hours a day. I problem I am having is on odd occasions throughout the day the PC browser error with “Server taking too long to respond error”. What I am trying to find our is if I have the correct setting in the httpd.conf file on the server. Any help or advice anyone can provide would be very helpful. Best regards Dereck Server config file: httpd.conf ServerRoot "/etc/httpd" PidFile run/httpd.pid Timeout 120 KeepAlive On MaxKeepAliveRequests 200 KeepAliveTimeout 5 <IfModule prefork.c> StartServers 8 MinSpareServers 5 MaxSpareServers 20 ServerLimit 256 MaxClients 254 MaxRequestsPerChild 4000 </IfModule> <IfModule worker.c> StartServers 2 MaxClients 150 MinSpareThreads 25 MaxSpareThreads 150 ThreadsPerChild 25 MaxRequestsPerChild 0 </IfModule>

  Read the article

• Mac Mini server (10.6) behind router with FQDN hostname

  - by thechriskelley

  I have a Mac Mini running Mac OS 10.6.6 Server that will be part of a local network, and a static IP from my ISP. I'd like to set up DNS for the Mini with a FQDN as the hostname (example.com) properly. The Mini is behind a router (Apple Airport Extreme) and is given a private, static IP address. I can't assign it the public static IP directly because it's behind a router with DHCP/NAT for other machines on the local net. My end goal here is for services to resolve to the server properly from outside and inside the local network to users via example.com (and subdomains like mail.example.com, www.example.com), which will point to the public static IP assigned to the router. Will DNS work/resolve properly (for mail services and other subdomains) if it has a private ip address, but the necessary services are forwarded properly through NAT? I'm open to any (hopefully better) suggestions, as my current setup doesn't seem like it's the best way. Currently, more hardware or another public static IP is not possible. With the current setup, it seems as though one static IP is not necessary anyway. Thanks in advance for any insight.

  Read the article

• Compaq R4000 laptop randomly locking up

  - by Josh

  I have a Compaq R4000 laptop with 2GB of RAM, running Ubuntu Linux 9.10. It is randomly locking up on me, approximately once every two days. I have a second partition with Windows XP Home installed, and I have had the system lock up in XP as well, meaning I believe this is a hardware issue. I have run two passes of Memtest86+ with no errors. The system has a fan that has died, so I initially suspected overheating. However the system just locked up on me while I was in the middle of typing a script to warn me / shut down if the temperature was too high. When the lockup happened the temperature was 88°F, so I am now starting to believe that may not be the issue. When the system locks up, I cannot SSH in nor ping it. Nothing shows in syslog when I reboot. I have configured it to send syslog messages to a local server as well and no messages appear on that server when the lockup happens. I am open to any and all advice!

  Read the article

• How to connect the virtual networks of vmware guests running on different hosts?

  - by gyrolf

  In a test setup, we are running several virtual machines on a single vmware workstation host. All virtual machines are connected via a "host only" network. This runs fine up to 2 or 3 virtual machines (depending on the host hardware). To allow more virtual machines, we want to use more host machines. Details about the environment and applications: Host PCs are running Windows XP in a corporate intranet. VMware used is Workstation 6.5 Guests are running Windows Server 2003 All guests act as Web Servers One of the guests additionally acts as Windows File server, offering shared folders for the other guests to connect to. Restrictions: VMware guests shall not be visible from the intranet. Changes to the host PC are restricted by corporate policy. In the virtual network, no domain controller exists. All virtual machines are member of the same workgroup. Running the virtual network as NAT is possible. Port forwarding might be used if it does not conflict with ports used by the host PC. Looking for a solution, I found hints about using router or vpn software on the hosts, but without any details how to setup. (I found a similar question Sharing the network between 2 VMware hosts, but the answer was not sufficient for me.)

  Read the article

• Can't view other computers on Network

  - by Darkart

  Systems: My Machine: Windows 7 Ultimate connected through ethernet into router Her Machine--Other Machine: Windows 7 Ultimate connected through wireless Router:F5D8236-4 N Wireless Router Version 1 Firmware: 2.01.03 (Apr 28 2009) ISP: Comcast Problem: I can not view the "Other Machine" on the network at all. I opened command prompt and ran net view and saw the pc name. I tried pinging the pc and it times out. Went inside the router and tried viewing the computer on the DHCP list and it can not be seen. I restored the router back to default settings and firmware and completely reset the modem and router, and created home group. I went to the other machine to configure home group settings and made sure that both PC's had identical settings. She was able to see my machine but I could not see hers. I restarted both machines and now we cant see each other at all. Also her PC ("Other Machine") had exclamation mark in the wireless icon but was connected just fine. There is no firewalls on currently or anti-virus enabled, and still can not see each other. Right now I am checking for updated drivers for the wireless card, but my question is could it be the router or something hardware related? I have went through all the settings in the Home group and visited most FAQ's and still no luck. Also as it stands I can not view her machine inside the router DHCP Client List :(

  Read the article

• Tips on setting up a virtual lab for self-learning networking topics

  - by Harry

  I'm trying to self-learn the following topics on Linux (preferably Fedora): Network programming (using sockets API), especially across proxies and firewalls Proxies (of various kinds like transparent, http, socks...), Firewalls (iptables) and 'basic' Linux security SNAT, DNAT Network admininstration power tools: nc, socat (with all its options), ssh, openssl, etc etc. Now, I know that, ideally, it would be best if I had 'enough' number of physical nodes and physical network equipment (routers, switches, etc) for this self-learning exercise. But, obviously, don't have the budget or the physical space, nor want to be wasteful -- especially, when things could perhaps be simulated/emulated in a Linux environment. I have got one personal workstation, which is a single-homed Fedora desktop with 4GB memory, 200+ GB disk, and a 4-core CPU. I may be able to get 3 to 4 additional low-end Fedora workstations. But all of these -- including mine -- will always remain strictly behind our corporate firewall :-( Now, I know I could use VirtualBox-based virtual nodes, but don't know if there are any better alternatives disk- and memory- footprint-wise. Would you be able to give me some tips or suggestions on how to get started setting up this little budget- and space-constrained 'virtual lab' of mine? For example, how would I create virtual routers? Has someone attempted this sort of thing before: namely, creating a virtual network lab behind a corporate firewall for learning/development/testing purposes? I hope my question is not vague or too open-ended. Basically, right now, I don't know how to best leverage the Linux environment and the various 'goodies' it comes with, and buying physical devices only when it is absolutely necessary.

  Read the article

• Black Screen and System Hang - Possibly CPU overheating

  - by Mahesh

  I have this old computer - P4 2.0ghz, 1.2GB RAM and onboard graphics(no external card), 80GBHDD. It has xubuntu installed on it and it regularly hangs when it takes more system resources for say like graphical programs, too many tabs on firefox etc. It just either hangs the system or shows black screen. Tested if it was issue of HD but it wasn't because i have used linux livecd and problem is still the same even if I have removed the HD. I have also tested with USB linux (puppy linux and ubuntu linux on 8gb drives). Tested windows XP as well on this HD and results are the same. Tested another HD on this machine, results are still the same with it. System hangs or goes black screen and requires restart. I thought later it could be thermal heat issue and then applied thermal paste on heatsink but still it fails to work for me. It continues to show symptoms. Another thing which was yet to be tested is changing of CPU fan which was not done because I have not found any fan for old pentium 4 machine in the market. I have to hit online stores (but i am in india and it's hard to find it in online shops which can deliver it to me). So far I don't see this as HD or Monitor or OS issue because I have tested with other HD and results are the same. So it could be either CPU fan or motherboard? What could be possible issue with the hardware?

  Read the article

• Random Hard Freeze of Windows 7 (is Kaspersky to be blamed for this?)

  - by Christian Ivicevic

  The last few weeks I experienced a new strange behavior of my computer. Sometimes Windows 7 just freezes with no real reason at all. While listening to music for example the playback hangs and you can hear a very nasty sound. Neither mouse nor keyboard input is handled and everything is just stuck. Using Ubuntu this does not happen, so I think it is just a matter of driver issues or a Windows 7 bug. Furthermore I am really suspicious about Kaspersky (Internet Security 11) and so I let it perform a complete virus scan while no other app is running. At about 50% it happened again and I needed to restart the computer by holding the power button the bad way... A really weird thing is that playing Skyrim this happened once, however music playback did not stop. Only the framerate dropped to 0 and sometimes for a few seconds I am able to move. Therefore I am really confused as furthermore no bluescreen pops up. Memtest told me that everything seems to be alright... Can anyone explain me which data you need about my hardware and software (and which tools tools to use to gather the informatik) to be able to provide any help on my problem?

  Read the article

• How to whitelist external access to an internal webserver via Cisco ACLs?

  - by Josh

  This is our company's internet gateway router. This is what I want to accomplish on our Cisco 2691 router: All employees need to be able to have unrestricted access to the internet (I've blocked facebook with an ACL, but other than that, full access) There is an internal webserver that should be accessible from any internal IP address, but only a select few external IP addresses. Basically, I want to whitelist access from outside the network. I don't have a hardware firewall appliance. Until now, the webserver has not needed to be accessible externally... or in any case, the occasional VPN has sufficed when needed. As such, the following config has been sufficient: access-list 106 deny ip 66.220.144.0 0.0.7.255 any access-list 106 deny ip ... (so on for the Facebook blocking) access-list 106 permit ip any any ! interface FastEthernet0/0 ip address x.x.x.x 255.255.255.248 ip access-group 106 in ip nat outside fa0/0 is the interface with the public IP However, when I add... ip nat inside source static tcp 192.168.0.52 80 x.x.x.x 80 extendable ...in order to forward web traffic to the webserver, that just opens it up entirely. That much makes sense to me. This is where I get stumped though. If I add a line to the ACL to explicitly permit (whitelist) an IP range... something like this: access-list 106 permit tcp x.x.x.x 0.0.255.255 192.168.0.52 0.0.0.0 eq 80 ... how do I then block other external access to the webserver while still maintaining unrestricted internet access for internal employees? I tried removing the access-list 106 permit ip any any. That ended up being a very short-lived config :) Would something like access-list 106 permit ip 192.168.0.0 0.0.0.255 any on an "outside-inbound" work?

  Read the article

• Setting up a PC for the Kids

  - by Martin Clarke

  I recently finished building a new PC from scratch; and then I decided to treat myself to a new widescreen monitor. I'm left with a bit of a conundrum with what to do with my old box. I'm considering a few options such as a file server, putting Linux on it, putting it elsewhere in the house or giving it to a member of the family and so on. But to be honest, I don't really think it would get much use. I've started thinking about putting together something for my kids. The oldest is coming up on 4 in a couple of months and he's used my PC and Macbook (supervised!) before for playing jigzaw puzzles, babysmash and so forth. He's also uses the computer at his nursery (Kindergarden for North Americans!). So, its got me thinking about setting something up for him (bonus for his brother who is 2). I was wondering what others had done when trying to put together something for their kids? Some points for consideration: Operating System? Software? Anti-virus Internet (probably blocking?) Hardware (I've seen some keyboards designed with kids in mind)

  Read the article

• Network profile reverts to 'Unidentified' following Windows Update reboot

  - by user140575

  I have searched high and low for a solution to this problem. I have multiple servers running Windows 2000 Server as well as Windows Server 2003, 2003 R2, and 2008 R2. All of these servers are on the same Active Directory domain. The servers run showing the network profile as Domain Network, which is fine and correct. However, when a Windows update is installed, the server changes the profile to Unidentified Network once it has rebooted. This then doesn't allow any traffic to the server. For security reasons, we can't turn the firewalls off for. The only way to fix the problem is to physically be in front of the machine and work on it to change the profile back. Once the Profile has been reinstated to the Domain profile, it will be fine until the next month's update. This happens on all the Windows software mentioned above. The machines are not all identical, so it's not a hardware problem either. If anyone can help I'd be very grateful.

  Read the article

• Please insert a disk into SD/MMC - Vista problem [closed]

  - by Naunidh

  Possible Duplicate: Please insert a disk into SD/MMC - Vista problem Hi I tried pushing my 2GB micro SD card using the inbuilt card reader. On clicking the drive I get "Please insert a disk into SD/MMC". This problem is really frustrating. The card works fine on other computers so does the microSD to SD attachment. I have done following o fix. - Updated Vista and installed SP1. - Updated the TI drivers for FlashDrive. - Checked Vaio site for updates (none required). - Added a new entry HKLM\SYSTEM\ControlS* et001\Services\tifm21\Parameters/SDParam=1 took the hint from (http://tinyurl.com/nk33tp) I have restarted the PC multiple times. As soon as I put the card in, the SD/MMC device icon blips, so it seems the hardware is at least detecting something. The card reader was working fine few days back. I guess some windows update has broken something, does any one have any idea on how to proceed. MY laptop is VGN-N365E.

  Read the article

• Can I make two wireless routers communicate using the wireless?

  - by Dana Robinson

  I want to make a setup like this: cable modem <-cable- wireless router 1 <-wireless- wireless router 2 in another room <-cables- PCs in another room Basically, I want to extend my network access across the house and then have a bunch of network jacks available for my office PCs. Right now, I have a cable modem going to a wireless router in one room and a PC with a wireless PCI card in it in the office on the other side of the house. I use internet connection sharing with the other PCs in the office. The problem is that ICS is flaky, especially when I switch to VPN on the Windows box to access files at work. I picked up a wireless USB adapter that I thought I could share among the PCs I work on but I'm not very happy with it so I'm going to return it (NDISwrapper support for it is poor). Is this possible? My wireless experience so far has been pretty straightforward so I have no idea what kind of hardware is available. I've looked at network extenders but those just look like repeaters for signal strength. I want wired network jacks in my office.

  Read the article

• Time not propagating to machines on Windows domain

  - by rbeier

  We have a two-domain Active Directory forest: ourcompany.com at the root, and prod.ourcompany.com for production servers. Time is propagating properly through the root domain, but servers in the child domain are unable to sync via NTP. So the time on these servers is starting to drift, since they're relying only on the hardware clock. WHen I type "net time" on one of the production servers, I get the following error: Could not locate a time-server. More help is available by typing NET HELPMSG 3912. When I type "w32tm /resync", i get the following: Sending resync command to local computer The computer did not resync because no time data was available. "w32tm /query /source" shows the following: Free-running System Clock We have three domain controllers in the prod.ourcompany.com subdomain (overkill, but the result of a migration - we haven't gotten rid of one of the old ones yet.) To complicate matters, the domain controllers are all virtualized, running on two different physical hosts. But the time on the domain controllers themselves is accurate - the servers that aren't DCs are the ones having problems. Two of the DCs are running Server 2003, including the PDC emulator. The third DC is running Server 2008. (I could move the PDC emulator role to the 2008 machine if that would help.) The non-DC servers are all running Server 2008. All other Active Directory functionality works fine in the production domain - we're only seeing problems with NTP. I can manually sync each machine to the time source (the PDC emulator) by doing the following: net time \\dc1.prod.ourcompany.com /set /y But this is just a one-off, and it doesn't cause automated time syncing to start working. I guess I could create a scheduled task which runs the above command periodically, but I'm hoping there's a better way. Does anyone have any ideas as to why this isn't working, and what we can do to fix it? Thanks for your help, Richard

  Read the article

• Windows 7 Black Screen On Boot, Seperate Bootable VHD Works Fine

  - by David Osborn

  I have a Window 7 x64 install with a bootable VHD (also Windows 7 x64). I was having problems getting my homeserver to do backups (VSS erred) so I ran check disk and used a tool from MS (cleanc2r.exe) to remove an empty Q drive from the VHD that I believe was a result of installing Office 2010 Beta. (All of this was done on the bootable VHD, not the main install.) Now I can't boot into the main install. It gets past the Starting Windows screen and then goes black. I can still boot into the bootable VHD and everything works fine from there. I have tried to boot the main install in Safe Mode/Safe Mode with Networking/and Safe Mode command prompt and it has the same issue. I ran chkdsk /r on the main install and after doing all the work there was a message about correcting some free space that was marked as allocated and also that it was unable to make an entry into the event log. I tried the startup repair utility and it found no problems. I don't see the setting for restore to last know good configuration so I couldn't do that. I don't recall installing anything new to the main install nor having hooked up any new hardware recently.

  Read the article

• Hyper-V Guests Dying

  - by Jon Rauschenberger

  I just hit my THIRD instance of a Hyper-V guest machine dying with the exact same behavior. In all three instances we are hosting WS2008 guests on a WS2008 host. AFter a config change, we reboot the guest and the guest OS comes up but in a very cripled state. Specifically, we are able to log into the guest, but can't launch any apps and the guest never comes active on the network. I opened a support ticket with MS the second time this happened and they focused in on the DCOM subsystem not coming up...best explanation they could provide was that permissions on key system files got corrupted. I eventually gave up on the ticket after close to 10 hours on the phone trying different things that were going no where. What really concerns me is that we have now seen the exact same thing happen to a guest hosted on a completly differet host machine. There is zero hardware overlap between the two. Has anyone seen this before?? It's really odd behavior, but it also seems like there's a pattern here that's concerning me. Thanks, jon

  Read the article

< Previous Page | 663 664 665 666 667 668 669 670 671 672 673 674  | Next Page >