Search Results

Search found 25797 results on 1032 pages for 'source formatting'.

Page 667/1032 | < Previous Page | 663 664 665 666 667 668 669 670 671 672 673 674  | Next Page >

• Second Monitor Detected, but not receiving a signal after upgrading to 12.04

  - by user62458

  After I upgraded to 12.04, my second monitor is detected (in display settings), but will not power on. I have scoured the Internet and forums for a solution and I can't find anything. I have found a couple people with the same problem, but never a solution for it. I am no expert, but I'm certainly not a noob. My computer uses AMD Radeon 6250 graphics, but I do NOT want to use the proprietary graphics drivers. They refuse to work properly with my second monitor (they ATI drivers will only mirror screens, and I've done everything to try to fix it, and I DON't want mirrored screens) Not to mention that the default open-source video drivers seem to work much better than the proprietary anyway! Again, Ubuntu's default video drivers work fine, and they even DETECT the second monitor (Dell 19'). I can drag stuff off the screen and put it on the 'space' of the second monitor and even a screen-shot shows that there are two monitors active; but the monitor is OFF. It will not power on. It goes into 'power-save' mode because it is not receiving a signal. For some reason it is not getting the signal to power on, even though Ubuntu thinks the monitor is working properly. I had this working fine on my Sony VAIO yesterday (with Radeon graphics/default Ubuntu video drivers). I upgraded to a Samsung Series 3 and now I have this issue. I can't for the life of me figure out why the monitor is connected, detected and I have screen space for the monitor, but the screen won't turn on! XRANDR Output: Screen 0: minimum 320 x 200, current 1366 x 768, maximum 8192 x 8192 VGA-0 connected (normal left inverted right x axis y axis) 1440x900 59.9 + 75.0 1280x1024 75.0 60.0 1152x864 75.0 1024x768 75.1 70.1 60.0 832x624 74.6 800x600 72.2 75.0 60.3 56.2 640x480 72.8 75.0 66.7 60.0 720x400 70.1 LVDS connected 1366x768+0+0 (normal left inverted right x axis y axis) 344mm x 194mm 1366x768 60.1*+ 1280x720 59.9 1152x768 59.8 1024x768 59.9 800x600 59.9 848x480 59.7 720x480 59.7 640x480 59.4 HDMI-0 disconnected (normal left inverted right x axis y axis)

  Read the article

• Organize code in Chef: libraries, classes and resources

  - by ColOfAbRiX

  I am new to both Chef and Ruby and I am implementing some scripts to learn them. Now I am facing the problem of how to organize my code: I have created a class in the library directory and I have used a custom namespace to maintain order. This is a simplified example of my file: # ~/chef-repo/cookbooks/mytest/libraries/MyTools.rb module Chef::Recipe::EP class MyTools def self.print_something( text ) puts "This is my text: #{text}" end def self.copy_file( dir, file ) cookbook_file "#{dir}/#{file}" do source "#{dir}/#{file}" end end end end From my recipe I call both methods: # ~/chef-repo/cookbooks/mytest/recipes/default.rb EP::MyTools.print_something "Hello World!" EP::MyTools.copy_file "/etc", "passwd" print_something works fine, but with copy_file I get this error: undefined method `cookbook_file' for Chef::Recipe::EP::FileTools:Class It's clear to me that I don't know how to create libraries in Chef or I don't know some basic assumptions. Can anyone help me, please? I am looking for a solution of this problem (organize my code, libraries, use resources in classes) or, better, a good Chef documentation as I find the documentation very deficient in clarity and disorganized so that research through it is a pain.

  Read the article

• Render a 3D image as a 2D vector image

  - by Clinton Blackmore

  Is there any software that will take a 3d model (in any format) and allow you to render it as a 2D vector image (preferable as either an .SVG or .PDF)? My intention is to render LEGO building instructions this way. While there are many tools that let you view them or generate nice, rasterized output, I'd really like to be able to generate vectorized output. Textures are not needed, and hidden line removal may not be needed. I could use a tool that works on any platform (although my preference is OS X, Linux, then Windows). Open source is preferred. If no one knows of a tool that does this, does anyone have a good recommendation of something to hack on and add a feature to output via Cairo?

  Read the article

• eTrayz: Replace base system with a bootstrapped Debian

  - by knoopx

  I bought an eTrayz NAS time ago. The device is more or less good but it ships with a closed-source custom linux and a bunch of broken web-apps. I wanted to replace the whole system with a raw Debian installation. I successfully bootstrapped a Lenny Debian into a chroot and I'm able to use use it. However I would like it to be the default system and to boot automatically at login. The device itself ships with a bundled 2.6.24.4 kernel. I think the kernel is on a dedicated flash memory so I would prefere not to re-flash it. What do you think is the best way to accomplish it?

  Read the article

• How can I prevent my computer from waking up accidentally?

  - by Ivo Flipse

  When I put my computer into sleep mode, it will wake up while I'm away from it. There's nothing near the computer that could move the mouse or accidentally press a button and I have no idea what might be causing it. I tried checking what woke it, apparently LASTWAKE only tells me that it has been in sleep mode, not what woke it up. I also couldn't find anything in my Power Options regarding Sleep that seems off. Poking around in the Event Viewer I notice the following: The Power-Troubleshooter event at the top notes the following: The system has returned from a low power state. Sleep Time: ?2012?-?10?-?27T11:31:53.408927000Z Wake Time: ?2012?-?10?-?27T12:25:51.887029300Z Wake Source: Unknown So does anyone have an idea to find out what might be causing it and how I can prevent my computer from randomly waking up?

  Read the article

• PHP Debugging

  - by Bob Porter

  Originally posted on: http://geekswithblogs.net/blogofbob/archive/2013/06/25/php-debugging.aspxI have been experimenting setting up a PHP development environment. I have been trying on Windows, Linux (Ubuntu) and Mac OS X. So far my favorite environment is on Mac OS X. I have tried a number of IDE's and debuggers as well.  IDE's Eclipse with the PDT Add On The PDT version of Eclipse Aptana Zend Netbeans  Debuggers Zend XDebug So far the only environments that I could get running quickly were Zend and Netbeans. Eclipse is a nightmare of versions and capabilities. I could only get Eclipse working well on Windows. On Ubuntu I was able to get the debugger working once. Thats it, one session, then it never worked again. I love the Zend tools and environment and it worked well everywhere I tried it, but it was beyond my budget.  Aptana also worked best on Windows, on Mac OS X it was fragile and I never could get debugging to work.  Netbeans worked first time, every time, every where. With one oddity, after several debugging sessions the debugger would refuse to connect. On every platform, I would end having to reboot to restore debugging, which would then work correctly for quite some time. I am sure I will discover that some process is hanging and there is a less intrusive way to clear the issue, but for now rebooting always works. In a future post I will go over how exactly I set my environment up, for now I have decided to stay with OS X. By the way, I did NOT use MAMP or the Zend Server, I stuck with PHP compiled and built from source, as well as Apache and MySQL installed locally. I use Homebrew as a package manager for OS X. I tried PORT but did not like the fact I had to sudo all the time to use it, and it installed things in /opt which I was not used to. Homebrew does sandbox the apps but it is nice enough to symlink them to their "normal" locations usually in /usr/local.

  Read the article

• Microsoft Press Deal of the Day 11/Oct/2012 - CLR via C#, 3rd Edition

  - by TATWORTH

  Today's Deal of the Day from Microsoft Press at http://shop.oreilly.com/product/9780735627048.do?code=MSDEAL is CLR via C#, 3rd EditionThe deal expires probably 23:59 PT, today 11/Oct/2012. Remember to use the code MSDEAL at checkout."Dig deep and master the intricacies of the common language runtime (CLR) and the .NET Framework 4.0. Written by a highly regarded programming expert and consultant to the Microsoft® .NET team, this guide is ideal for developers building any kind of application-including Microsoft® ASP.NET, Windows® Forms, Microsoft® SQL Server®, Web services, and console applications. You'll get hands-on instruction and extensive C# code samples to help you tackle the tough topics and develop high-performance applications." This is a very through book about Dot Net that I have completed reviewing. I commend it to all C# development teams and to individual developers with at least a year's worth of C# experience. The only drawback is that there should be a VB.NET equivalent book for the benefit of the many programming shops that have chosen VB.NET.For further details about the book see: http://oreilly.com/catalog/9780735627048The author has made some useful source available athttp://www.wintellect.com/Resources/Downloads/PushPin

  Read the article

• Web master tools is throwing out 404 errors on link not on page

  - by plantify

  Webmaster tools is showing thousands of 404 errors, where pages on the site are referring to another incorrect url. For example, URL not found www.plantify.co.uk/shop/=, linked from http://www.plantify.co.uk/shop/gift-voucher and http://www.plantify.co.uk/shop/special-plant-offers. I obviously have checked the source and cannot find any references to this link on any page. The only consistent issue is that it only seems to report this error on pages with two section i.e. www.plantify.co.uk/shop does not report any error whilst all pages with www.plantify.co.uk/shop/xxx (where xxx can be several different pages such as gift-voucher) all report this. I cannot seem to duplicate this error. I have run a link checker (we use Screaming Frog) and it does not report this error. I have fetched these pages as a bot, and these do not report this error. I am at a total loss. I cannot even duplicate the issue, but it is most definitely an issue, as Webmaster Tools is reporting new errors every day. Is this perhaps google bot doing its own thing?

  Read the article

• How to do a 3-tier using PHP [closed]

  - by Ric

  I have a requirement from a client for my PHP Web application to be 3-tier. For example, I would have a web server on Apache in the DMZ, but it should NOT contain any DB connections. It should connect to a Middle server that would host the business objects but be behind the firewall. Then those objects connect to my SQL cluster on another server. I have actually done this using .NET, but I am not sure how to setup my stack using PHP. I suppose I could have my UI front tier call the middle tier using REST based web services if I create my middle tier as a second web server, but this seems overly complex. The main reason for this is advanced security: we can not have any passwords on the DMZ first tier web server. The second reason is scalability - to have multiple server on different tiers that can handle the requests. The Last reason is for deployment - it is easier if I can take one set of servers offline for testing before putting them back in production. Is there a open source project that shows how to do this? The only example I can find is the web server hosting files from a shared drive on another machine (kind of how DotNetNuke pretends to be 3-tier), but that is NOT secure.

  Read the article

• Copy & Paste Images Wiki functionality?

  - by Jakub

  I was discussing this with some coworkers, they would like a wiki, but are turned off by the need to constantly [browse] and [upload] files. They like the functionality of Lotus Notes that they can copy & paste screenshots (or crops etc) directly into Notes databases / libraries. But they are not fans of Lotus notes behond that (performance, etc,) Anyone work with a free (open source hopefully) wiki of documenting application that just allows copy & paste of text & image content? Would be great to have one internally installed that we could use for documentation without constantly uploading/attaching files. Not sure if I am asking for functionality that is not available in a browser.

  Read the article

• Is Zabbix the right tool for me?

  - by hortitude

  I just want to monitor a small handful of servers (less than 10). From reading various places it sounds like the top leading contenders (for open source at least) are: nagios munin zabbix From what I have read a lot of people tend to use munin and nagios together -- munin for history and graphs, and nagios for alerting. On the other hand it sounds like Zabbix is a more complete solution and easier to configure than either of the other two. So I was thinking of going that route. My thoughts right now are: What are the general disadvantages of Zabbix? Does Zabbix have a small footprint on boxes it is monitoring? Do I really need to setup an entire other server for it? I currently have a server that is under very light load -- can I dual purpose it?

  Read the article

• How *NAT* was Implemented in Home Based Routers ? [closed]

  - by Sumit Arora

  Different Types of Home-Based Routers Exist, and those routers provide NAT Feature as well e.g; and most of them are Port Restricted. Q-1 : What kind of Base Softwares Manufactures use to develop NAT Functionality ? Q-2 : Is that Technology Proprietary ? Or some Open-Source used to develop that e.g; Firehol ? Q-3 : I am looking for a software which works exactly like a NAT,and by doing very basic configuration it should work either Symmetric NAT, Port Restricted NAT or Address Restricted NAT ? So that I can test some of my Network Application which are dependent on NAT via this way on same PC ? e.g; I can test my developed ICE Algorithms

  Read the article

• How do I stop someone from saturating my line & wasting CPU cycles

  - by JoshRibs

  My web host shows inbound & outbound traffic with mrtg. I have a steady 3.5mbps inbound traffic from Nigeria. Even assuming the source IPs & destination ports are blocked with Iptables & verifying nothing is listening on those ports, will the traffic still always pass through the switch & "get" to my server (where my server wastes CPU cycles "dropping" the packets)? Assuming I was setup with a hardware firewall, the traffic would still show in mrtg assuming the firewall is behind the switch? So is there any way to stop someone from saturating your 100mbps line, if they also have a 100mbps line? Other than filing an abuse complaint with the kind folks in Nigeria?

  Read the article

• Which one is better deal: iPed or Apple iPad?

  - by Evan Carroll

  The Chinese knockoff iPed is now in the wild and receiving a lot of attention? Does anyone know how the Android distribution it ships with compares with Apple iPad's software pack? How does the look-and-feel of the iPed fit with the Apple iPad? Quite frankly, I have little interest in Apple products because of the company policy. But, cheaper comparable hardware running open-source software is pretty interesting... Anything useful to add.. Here are the Apple iPad specs for comparison. The iPed is priced at $199.00, the Apple iPad starts at $499.00 .

  Read the article

• Scripting help - need to get phone number of AD accounts and then add them to contacts in trusted domain

  - by TheCleaner

  I have domain accounts that I have created as contacts in another trusted domain so that they can see them in their Exchange GAL. I need a way to extract the phone number field from UserA (user account) in DomainA and import it into UserA (contact) in DomainB. I get the logic, it's just the code (vbscript/powershell/whatever) that eludes me. The logic as I see it: Connect to source AD (ou/subtree) Extract user accounts from OU and subcontainers including first name, last name, display name, and phone number Connect to target AD (ou/subtree) Verify/match contact with extract in #2 above based on display name Update phone field with phone number in extract Write log of success and failures Anybody able to help?

  Read the article

• Grub2 attempting to boot hd1 when it should boot hd0

  - by JoBu1324

  I'm attempting to perform a "normal" install on a USB3 SSD (I don't know if it is noteworthy, but I don't have a swap partition). The installation proceeds normally (I'm installing from a USB2 device I created using LiLi Boot, with a copy of Ubuntu 12.10 64bit that I downloaded directly from the source. The system I'm running Ubuntu on has had a more traditional installation of ubuntu running on it without issue (also 12.10), so I know that everything works A-OK when booting from a 7200RPM internal disk. There are a number of oddities that I've noticed so far, including graphics corruption, but the first and most pressing issue is that Grub2 refuses to recognize the correct hd. From /boot/grub/grub.cfg: if [ x$feature_default_font_path = xy ] ; then font=unicode else insmod part_msdos insmod ext2 set root='hd1,msdos1' if [ x$feature_platform_search_hint = xy ]; then search --no-floppy --fs-uuid --set=root --hint-bios=hd1,msdos1 --hint-efi=hd1,msdos1 --hint-baremetal=ahci1,msdos1 b58ee4f7-d41d-400a-b7b8-18bd1f0ae9d3 else search --no-floppy --fs-uuid --set=root b58ee4f7-d41d-400a-b7b8-18bd1f0ae9d3 fi font="/usr/share/grub/unicode.pf2" fi This is from a 100% fresh install of linux (first boot), which was installed while no hard drives were connected to the system, other than the USB2 LiLi drive. The system refuses to boot unless I change the hd1,msdos1 - hd0,msdos1 in the grub menu at boot, when it is the only disk device connected to the PC. What options are left for me to troubleshoot this issue? I've been racking my brains and taxing the internet trying to dig up something on this problem, but now I'd like to see if the Ubuntu community can rise to the challenge and help me fix this boot problem. This is the second time I've attempted this particular setup. The first time, after days of wasted time, I managed to get it to boot every other boot - i.e. every even boot it would boot into Ubuntu like it was happy; every odd boot it would boot into the BusyBox or Grub prompt. At one point it complained that it couldn't find /dev/disk/by-uuid/[the disk], which I found most perplexing, since the disk was there and booted before and after the occurrence (with intervention).

  Read the article

• Microsoft Lowers Cloud Barrier To Entry

  - by Herve Roggero

  Once in a while, the technology stack changes enough to create a disturbance in the IT industry. Microsoft did just that today and has officially closed the gap with its #1 competitor: Amazon. What is remarkable is that Microsoft is no longer an alternative to Amazon, it is becoming a clear leader in that space. Some of the new features include official support for durable Virtual Machines with high availability (cross-geographic replication), free WebSites to try Azure, MySQL database at no charge, a new distributed low-latency cache feature, Linux support, support with existing VPN hardware for seamless on-premise integration, a new partner ecosystem and much, much more. Amazon had an edge against Windows Azure in the IaaS (Infrastructure as a Service) space, until now. With the latest release from Microsoft Azure, the gap has been filled. In fact, it seems Amazon may now have a gap to fill… This is great news to everyone; it seems that cloud offerings are becoming more standardized with the more mature cloud providers, and the management stack and quality of service of each cloud provider is increasingly becoming the differentiator. With today’s announcements, it is becoming clear that cloud providers are pushing hard to increase their service footprint and lowering typical barriers to entry such as support for open-source operating systems, free trial offers, higher availability, faster deployment times and simpler enterprise integration.

  Read the article

• Why my browsers display XML files as blank pages?

  - by n1313

  Every time I open an XML file, all I get is blank page instead of tag tree. The file itself is correct and loads okay, I can see it via View Source or in the Firebug. I've tried turning off all my addons and tried running Firefox in safe mode, but the problem was not solved. I'm guessing that I've messed up my configuration somehow and Firefox now tries to render XML files as HTML ones. I've tried googling, but with no success. Help, please? UPD: example file: http://lj.lain.ru/3/1273657698603.sample.xml Also I've noticed that somehow all of the browsers on the machine are now acting the same, so I'm changing the question accordingly

  Read the article

• Does the password get sent in the clear when connecting to Sql-Server?

  - by Scott Chamberlain

  I was asked this today and I honestly did not know the answer. If you connect using a connection string without sspi to a server is there any way a 3rd party can intercept on the wire the password used to log in? "Data Source=MyServer;Initial Catalog=MyDatabase;User Id=sa;Password=CanThisBeSniffed;" I am not asking about MiTM attacks just someone listing on the same computer or on the same hub on the network with wireshark or something similar running. I fired up wireshark myself and did not see it in plain text but it could be a simple obfuscation or proper encryption, I just wanted to know which.

  Read the article

• Having problems with Grub2 booting Ubuntu from my External Hard Drive

  - by anonymous

  I installed Ubuntu on my external hard drive but it won't boot on my laptop. what do i do? i did some reading and traced the source of the problem to grub2. Apparently, grub2 doesn't use the device's UUID, and uses the linux directory instead (/dev/sdf2). This means that whenever i plug my E-HDD into a system that has a different number of drives connected to it, i won't be able to boot without editting the boot command. I don't understand it too well but that's what i got from what i read. Is there anyway to fix this?

  Read the article

• Complex nagios command

  - by gonvaled

  I have defined the following command for one of my service checks: define command{ command_name mycommand command_line $USER1$/check_by_ssh -p $ARG1$ -l nagios -i /etc/nagios2/keys/key1 -H $HOSTADDRESS$ -v -C 'source $USER10$ ; command.py -a get --alert-name $ARG2$ -q' } The problem is that it seems that nagios is parsing the command with the semicolon, and producing garbage which can not be executed. I have tried also putting a backslash \;, to no avail. If I run the command directly on the shell, it works. Which means that this is not a problem with check_by_ssh, but a problem on the parsing of the nagios configuration file. How can I debug this? Is there a way to get a listing of all the commands that nagios has parsed when reading the configuration files?

  Read the article

• Python Web Applications: What is the way and the method to handle Registrations, Login-Logouts and Cookies? [on hold]

  - by Phil

  I am working on a simple Python web application for learning purposes. I have chosen a very minimalistic and simple framework. I have done a significant amount of research but I couldn't find a source clearly explaining what I need, which is as follows: I would like to learn more about: User registration User Log-ins User Log-outs User auto-logins I have successfully handled items 1 and 3 due to their simple nature. However, I am confused with item 2 (log-ins) and item 4 (auto-logins). When a user enters username and password, and after hashing with salts and matching it in the DB; What information should I store in the cookies in order to keep the user logged in during the session? Do I keep username+password but encrypt them? Both or just password? Do I keep username and a generated key matching their password? If I want the user to be able to auto-login (when they leave and come back to the web page), what information then is kept in the cookies? I don't want to use modules or libraries that handle these things automatically. I want to learn basics and why something is the way it is. I would also like to point out that I do not mind reading anything you might offer on the topic that explains hows and whys. Possibly with algorithm diagrams to show the process. Some information: I know about setting headers, cookies, encryption (up to some level, obviously not an expert!), request objects, SQLAlchemy etc. I don't want any data kept in a single web application server's store. I want multiple app-servers to be handle a user, and whatever needs to be kept on the server to be done with a Postgres/MySQL via SQLAlchemy (I think, this is called stateless?) Thank you.

  Read the article

• What are some best practices for minimizing code?

  - by CrystalBlue

  While maintaining the sites our development team has created, we have come across include files and plugins that have proven to be very useful to more then one part of our applications. Most of these modules have come with two different files, a normal source file and a min file. Seeing that the performance and speed of a page can be increased by minimizing the size of the file, we're looking into doing that to our pages as well. The problem that we run into is a lot of our normal pages (written in ASP classic) is a mix of HTML, ASP, Javascript, CSS, and include files. We have some pages that have their JS both in include files and in the page, depending on if the function is only really used in that page or if it's used in many other pages. For example, we have a common.js and an ajax.js file, both are used in a lot of pages, but not all of them. As well as having some functions in a page that doesn't really make sense to put into one master page. What I have seen a few other people do online is use one master JS file and place all of their javascript into that, minify it, gzip it, and only use that on their production server. Again, this would be great, but I don't know if that fully works for our purposes. What I'm looking for is some direction to go with on this. I'm in favor of taking all of our JS and putting it in one include file, and just having it included in every page that is hit. However, not every page we have needs every bit of JS. So would it be worth the compilation and minifying of the files into one master file and include it everywhere, or would it be better to minify all other files and still include them on a need-to-use basis?

  Read the article

• Can vCenter 4 authenticate and authorize against a virtual directory server??

  - by iforeman

  Hi I am looking into Identity managment in our environment. We currently use Active Directory and Sun's Enterprise Directory server (6.3). I was wondering if I used the Virtual Directory Server of the Enterprise Directory server, would we be able to point the vCenter clients to this Directory service for authentication and authorization rather than at the AD source. The reason for this is that we have more users we want to add to the management role of this server but not all are in AD, a fair number are in the Sun LDAP v3. directory. Thanks in advance Ian

  Read the article

• puppet propagate variable from node to erb tamplate?

  - by picca

  Is it possible to declare variable in node and than propage it way down to the erb template? Example: node basenode { $myvar = "bar" # default include myclass } node mynode extends basenode { $myvar = "foo" } class myclass { file { "/root/myfile": content => template("myclass/mytemplate.erb") ensure => present, } } Source of mytemplate.erb: myvar has value: <%= myvar %> I know that my example might be complicated. But I'm trying to propagate file on (almost) all my nodes and I want its content to be altered depending on the node which requests the file. The $myvar = "bar" statement should be default when node does not override its value. Is there a solution to my problem? I'm using puppet 0.24.5

  Read the article

< Previous Page | 663 664 665 666 667 668 669 670 671 672 673 674  | Next Page >