Search Results

Search found 22756 results on 911 pages for 'power query'.

Page 671/911 | < Previous Page | 667 668 669 670 671 672 673 674 675 676 677 678  | Next Page >

  • Intel Motherboard Lightning Victim Dies Hard

    - by Stetson RDT
    Today, I have a more hardware-related question. I have an Intel board, and I really do not know which board it is, I built the machine for a relative, but he forgot to keep the documentation. Long story short, the computer was disconnected during a lightning storm, but a lightning strike travelled in via the ethernet cable (It was directly connected to a power brick commonly seen on those long distance ISP Wireless transmitters), and the motherboard was shocked. I am attempting to get this PC going. The problem is as follows: The computer will randomly reboot, just in the middle of anything as it pleases. May load to EFI (or whatever BIOS is nowadays), may load to bootloader, may even get to the OS. But before 5 minutes is up, the system will always die. Out of curiosity, I plugged my voltmeter in to a molex connector. On the 5V side, it gets a good, consistant +5.13V. On the 12V side, it fluctuates, as follows: Upon immediate startup, it soars to 12.11-12.13V. It will now do one of two things: it will immediately jump down to 12.04-12.05V, or hover for about a minute at 12.11-12.13, then jump down. It seems the longer the voltage stays at 12.11-12.13, the shorter the machine will stay running. Also, post codes, whenever the machine locks up, but does not die hard, seem to be between "AA" and "AC". Does this make any sense to anybody? Do you all think this motherboard is salvageable? It was an expensive bugger, and I'd prefer to not replace it.

    Read the article

  • What hardware would I need (approx) to run ESXi server?

    - by mr.b
    Hi, I am considering to purchase off-the-shelf commodity hardware in order to build server that will host virtual machines using ESXi server. Intended purpose for this server is NOT mission critical tasks. It will have to run perhaps 20-50 Windows XP/Vista/7 virtual machines (in total, but closer to 20 figure). Each guest would have to have 1-2 GB of ram, and probably two-three times more disk space than guest OS needs with clean install and all updates applied (that would be around 6-8 GB for XP, and i believe closer to 10-15 for win7). Those guests will act as a test ground for a new product that is network management software, thus guests will idle most of their time once initially loaded, but if I give them some task to complete, they should be able to perform reasonably well. Now, from what I have learned... CPU is usually not much of an issue (6 cores would do it), memory should not be lacking, but doesn't have to be sum of all guests, because of overcommitment... That leads me to IO, which is, as it seems, the bottleneck. Since I have very little experience with ESXi (and ESX, too) server, I'd like to ask: How much memory could I save by overcommitment, and how does it affect performance? Is 6-core cpu enough to run above described system? Would it be possible to run entire server off two (or even one) SSD drives (to host system virtual disks, with few additional HDDs (2-3) in RAID 0 to be used as secondary storage? I read somewhere that ESXi allows having something like "master image", essentially virtual machine that is "deployed" many times, so that disk space can be saved by having only differences stored by specific guests, instead of copying around whole virtual disks. Is this true, and how can this help me? Are there any other things I need to take into consideration when building this off-the-shelf solution? I should probably mention here that I'm fully aware of issues like SPOF regarding power supply, raid 0, etc, but since it's only a testing ground and not a production system, it's not so important for me. Thanks, B.

    Read the article

  • What is the solution to enable Dymo Turbo 400 Label Printer to work on Win 7 / 64-bit?

    - by mdpc
    It's Christmas time and time for printing labels for all those Christmas cards. I've upgraded to Windows 7 64-bit from XP. I've been unsuccessfully attempting to get the connected Dymo 400 Turbo label USB printer to work again. The latest manufacturer drivers have been successfully loaded and installed. The drivers are supposed to work on Windows 7/64-bit. The Win 7 system(s) in question are patched and up-to-date on that score. The Windows Update site responds with a driver when the USB cable is connected to this printer. The printer queue seems to be established correctly. What happens is that I submit a job to the printer (either using the DYMO s/w or not), it delays for a period of time, and then I get the message 'printing error'. Can't seem to locate the appropriate error in the new and improved event log. Several combinations of rebooting, re-installation and power cycling components fail to make the printer work. Sometimes during some type of reset it spits out the last thing to be submitted, but that seems intermittent. I have tried different USB cables and different USB (2.X) ports as well. I have run the Windows 7 troubleshooter it tries to fix the problem but alas it doesn't. Interestingly, trying the USB printer (and its associated manufacturer drivers and s/w) on another Windows 7 64-bit system has the identical failures noticed on the original system. I did not find anything on the manufacturers' site concerning this problem. The printer has no hardware problems or issues.

    Read the article

  • hyper-v cluster behavior when losing network connectivity

    - by ChristopheD
    Setup: (rather new) Hyper-V R2 cluster with 2 nodes (in failover configuration). Fysical host OS: Windows Server 2008. About eight VM's (mixed: Windows Server 2008 and Linux) Yesterday we had a power outage of about 15 minutes. Our blades are on UPS so the fysical host machines (Windows Server 2008) never went down. Our main switches are not on UPS (yet) and we saw the behaviour similar to the following (as distilled from the event logs). The nodes in the cluster lost means of communication (because the external switches went down). The cluster wants to bring down one (the first) of the nodes (to start failover?). The previous step impacts clustered storage where the virtual machine VHD's are located. All VM's got brutally terminated and were found in a failed state in the failover manager in the host OS'es. The Linux VM's were kernel panicking and looked like they had their disk ripped out. This whole setup is rather new to us, so we are still learning about this. The question: We are putting switches on UPS soon but were wondering if the above is expected behavior (seems rather fragile) or if there are obvious improvements configuration-wise to handle such scenario's ? I can upload an evtx file concerning what exactly was going on in case that's necessary.

    Read the article

  • Intel HD Graphics vs NVIDIA Quadro FX 380 PCI-E

    - by Michael
    I recently purchased an Acer Veriton which has an i5-650 processor, Windows 7 Pro (64 bit) and Intel HD Graphics listed as the video card. I also purchased a PNY nVIDIA Quadro FX 380 PCI-E card for improved picture and home video viewing and editing. I have already replaced the original 300 wattt power supply to a 430 watt Antec Truepower I had on hand and boosted the RAM to 8 gigs from the original 4. Question 1) Am I getting any improvement in visual quality or system speed with the Quadro or is it a waste of money and I should just save up to buy a bigger video card? This card was on sale for $115. If I am getting improvement then I need to ask another question. Question 2) Instructions for the Quadro installation are as follows... 1--Uninstall the existing VGA driver. -Remove the existing Display Driver via "Add or Remove Porgrams". -Shut down your computer. 2--Remove your Existing Graphics Board (or Disable Integrated 3D Graphics Controller). skipping instructions on how to remove existing graphics board -Systems with integrated (also know as on-board) 3D graphics may require you to disable the integrated 3D graphics system. Consult the owners or vendor manual that came with your PC on how to properly do this. So is the Intel HD Graphics considered a 3D graphics controller? If so should I just contact Acer or can anyone give me instructions? Thanks in advance for any help.

    Read the article

  • Platform to allow users to suggest and vote for ideas

    - by Simon
    I head up a support team for a software product. I am in the process of setting up a blog (Wordpress.org), a forum (PHPBB or maybe Vanilla), a means to view bugs (probably expose Jira), but would also like to allow our customers to suggest enhancement requests. Currently we have this as a 'contact form' via the blog, which feeds into a dedicated inbox, which the product manager reviews and may include some of these ideas into the product. However, I would like to give the clients more power/visibility over this. Have a look at ideas.arcgis.com. There are plenty of other similar sites as well. Users can suggest new ideas Other users can vote these ideas up or down (similar to Stack Exchange sites) Ideas that are voted highly will be given a higher priority over lower ones. We can report back on the # of ideas we implement, and potentially reject ideas with reasoning. Has anyone seen any platforms (ideally free) which would replicate something similar to this? I was half thinking of embedding Vanilla within a wordpress page, but need to look into it more.

    Read the article

  • Configuring two nearby WLANs: should I use the same ssid?

    - by Rory
    I'm configuring a home network for basic internet use (ie don't really need connectivity between workstations on the network). My brick walls mean a single wireless router doesn't provide good coverage throughout the house, so I have purchased two powerline adapters and now have the incoming modem/wireless router at one end of the house plugged into a powerline adapter, and at the other end of the house the other powerline adapter plugged into another wireless router. Currently the two wireless networks have different ssids. (The powerline adapters only do power-Ethernet; they're not wireless access points themselves.) This works well, except when I move between rooms and would ideally like my devices (iPad, phones, laptops) to switch from the weak to the strong signal. Sometimes there's enough signal that they hold on to the weak connects instead of switching to the strong one. Should I name the two networks the same ssid, and if so what is the actual effect? Do the signals get confused, is the bandwidth affected, will this help my devices seamlessly move from one to the other, or is the ssid just a cosmetic thing that actually doesn't have any impact on this situation? Are there any other settings that I should configure to make my setup optimal?

    Read the article

  • tomcat vs FULL J2EE Solutions

    - by jrhickey
    We are getting ready to make a major revision in our Web Application architecture which currently is running on JBoss 4.2. At first we were looking at moving from 4.2 to JBoss 6 but after some research tomcat may be a better solution for us. My first question is their anything that JBoss can do that tomcat cannot do assuming you are using the correct plugins. We do not really use EJB's in our solution and it would appear there are simple plugins for web services, JMX and other features. Tomcat appears to have much better support, faster upgrade cycles and many, many books. Since there is less to the system it also seems much easier to support from an admin point of view. What am I missing? The main features we want to enable are better clustering support and session replication / persistence. We will consider other application servers as well such as Glassfish / Geronimo. quote form a web article: Apache Tomcat is the world’s most widely used web application server, with over one million downloads per month and over 70% penetration in the enterprise datacenter. Tomcat is used to power everything from simple one server sites to large enterprise networks.

    Read the article

  • No audio with streaming video

    - by Chris Barnhill
    I am having trouble with audio when playing streaming videos. My sound card is fine. I know this because if I play sounds from my local machine, there's no problem. It's only when I try to play sounds from the internet that I lose audio. This only started happening recently when I did 2 things: I connected a USB headphone/microphone set to record screencasts I began recording/publishing screencasts from screenr.com. I have tried playing video both with the headset connected and without it connected: it makes no difference. If I record a screencast on screenr.com and preview it, I hear the audio. But once I publish is and play it, there is no audio. I also hear no audio with YouTube videos. I really hope someone can help. Thanks. The latest is that the problem went away after I powered my system off and on. A reboot didn't do it, I had to actually shut down the power.

    Read the article

  • Using Truecrypt to secure mySQL database, any pitfalls?

    - by Saul
    The objective is to secure my database data from server theft, i.e. the server is at a business office location with normal premises lock and burglar alarm, but because the data is personal healthcare data I want to ensure that if the server was stolen the data would be unavailable as encrypted. I'm exploring installing mySQL on a mounted Truecrypt encrypted volume. It all works fine, and when I power off, or just cruelly pull the plug the encrypted drive disappears. This seems a load easier than encrypting data to the database, and I understand that if there is a security hole in the web app , or a user gets physical access to a plugged in server the data is compromised, but as a sanity check , is there any good reason not to do this? @James I'm thinking in a theft scenario, its not going to be powered down nicely and so is likely to crash any DB transactions running. But then if someone steals the server I'm going to need to rely on my off site backup anyway. @tomjedrz, its kind of all sensitive, individual personal and address details linked to medical referrals/records. Would be as bad in our field as losing credit card data, but means that almost everything in the database would need encryption... so figured better to run the whole DB in an encrypted partition. If encrypt data in the tables there's got to be a key somewhere on the server I'm presuming, which seems more of a risk if the box walks. At the moment the app is configured to drop a dump of data (weekly full and then deltas only hourly using rdiff) into a directory also on the Truecrypt disk. I have an off site box running WS_FTP Pro scheduled to connect by FTPs and synch down the backup, again into a Truecrypt mounted partition.

    Read the article

  • Ubuntu 10.10 - disaster - what other linux for beginner?

    - by A-ha
    Guys, I've tried to install ubuntu (desktop and notebook ed) on my laptop and unortunately I have to say that as despite the fact that installation process supposed to be easy I couldn't finish installation of this system - didn't detect my keyboard or rather lost my keyboard as soon as I tried to switch on/off pad on my laptop. After I've discovered that, I started all over again (this time without touching my laptop's pad during installation) and yes, eventually it get to the end of installation. Unfortunately, when I've tried to switch my pad (sometimes I just do not want to use a mouse) the whole system froze. So I had to restart it with the power button and this time I didn't touch pad at all, plugged in mouse and tried to rearrange taskbars according to my liking (all taskbars on the top side of the screen and auto-hide on) and I gave up. It is so unfinished that I just can't be bothered to use it. I would like to have one linux system on my machine so I started googling and most of the links are to either ubuntu (which I just do not want to touch for now) and suse or commercial versions of linux. I do not really mind paying for something (and having experience with ubuntu I'd rather pay and have something pro then get it free and discover that it's unusable). So could someone please provide short list of linux distros which would be appropriate for a beginner, and I don't mind paying for it, I just want it to be a professional product.

    Read the article

  • need assistance with my.cnf - 1500% CPU usage

    - by Alan Long
    I'm running into a few issues with our new database server. It is a HP G8 with 2 INTEL XEON E5-2650 processors and 32GB of ram. This server is dedicated as a MySQL server (5.1.69) for our intranet portal. I have been having issues with this server staying alive - I notice high CPU usage during certain times of day (8% ~ 1500%+) and see very low memory usage (7 ~ 15%) based on using the 'top' command. When the CPU usage passes 1000%, that is when the app usually dies. I'm trying to see what I'm doing wrong with the config file, hopefully one of the experts can chime in and let me know what they think. See below for my.cnf file: [mysqld] default-storage-engine=InnoDB datadir=/var/lib/mysql socket=/var/lib/mysql/mysql.sock #user=mysql large-pages # Disabling symbolic-links is recommended to prevent assorted security risks symbolic-links=0 max_connections=275 tmp_table_size=1G key_buffer_size=384M key_buffer=384M thread_cache_size=1024 long_query_time=5 low_priority_updates=1 max_heap_table_size=1G myisam_sort_buffer_size=8M concurrent_insert=2 table_cache=1024 sort_buffer_size=8M read_buffer_size=5M read_rnd_buffer_size=6M join_buffer_size=16M table_definition_cache=6k open_files_limit=8k slow_query_log #skip-name-resolve # Innodb Settings innodb_buffer_pool_size=18G innodb_thread_concurrency=0 innodb_log_file_size=1G innodb_log_buffer_size=16M innodb_flush_log_at_trx_commit=2 innodb_lock_wait_timeout=50 innodb_file_per_table #innodb_buffer_pool_instances=4 #eliminating double buffering innodb_flush_method = O_DIRECT flush_time=86400 innodb_additional_mem_pool_size=40M #innodb_io_capacity = 5000 #innodb_read_io_threads = 64 #innodb_write_io_threads = 64 # increase until threads_created doesnt grow anymore thread_cache=1024 query_cache_type=1 query_cache_limit=4M query_cache_size=256M # Try number of CPU's*2 for thread_concurrency thread_concurrency = 0 wait_timeout = 1800 connect_timeout = 10 interactive_timeout = 60 [mysqldump] max_allowed_packet=32M [mysqld_safe] log-error=/var/log/mysqld.log pid-file=/var/run/mysqld/mysqld.pid log-slow-queries=/var/log/mysql/slow-queries.log long_query_time = 1 log-queries-not-using-indexes we connect to one database with 75 tables, the largest table has 1,150,000 entries and the second largest has 128,036 entries. I have also verified that our PHP queries are optimized as best as possible. Reference - MySQLtuner: >> MySQLTuner 1.2.0 - Major Hayden <[email protected]> >> Bug reports, feature requests, and downloads at http://mysqltuner.com/ >> Run with '--help' for additional options and output filtering -------- General Statistics -------------------------------------------------- [--] Skipped version check for MySQLTuner script [OK] Currently running supported MySQL version 5.1.69-log [OK] Operating on 64-bit architecture -------- Storage Engine Statistics ------------------------------------------- [--] Status: -Archive -BDB -Federated +InnoDB -ISAM -NDBCluster [--] Data in InnoDB tables: 420M (Tables: 75) [!!] Total fragmented tables: 75 -------- Security Recommendations ------------------------------------------- [!!] User '[email protected]' has no password set. -------- Performance Metrics ------------------------------------------------- [--] Up for: 1h 14m 50s (8M q [1K qps], 705 conn, TX: 6B, RX: 892M) [--] Reads / Writes: 68% / 32% [--] Total buffers: 19.7G global + 35.2M per thread (275 max threads) [!!] Maximum possible memory usage: 29.1G (93% of installed RAM) [OK] Slow queries: 0% (472/8M) [OK] Highest usage of available connections: 66% (183/275) [OK] Key buffer size / total MyISAM indexes: 384.0M/91.0K [OK] Key buffer hit rate: 100.0% (173 cached / 0 reads) [OK] Query cache efficiency: 96.2% (7M cached / 7M selects) [!!] Query cache prunes per day: 553614 [OK] Sorts requiring temporary tables: 0% (3 temp sorts / 1K sorts) [!!] Temporary tables created on disk: 49% (3K on disk / 7K total) [OK] Thread cache hit rate: 74% (183 created / 705 connections) [OK] Table cache hit rate: 97% (231 open / 238 opened) [OK] Open file limit used: 0% (17/8K) [OK] Table locks acquired immediately: 100% (432K immediate / 432K locks) [OK] InnoDB data size / buffer pool: 420.9M/18.0G -------- Recommendations ----------------------------------------------------- General recommendations: Run OPTIMIZE TABLE to defragment tables for better performance MySQL started within last 24 hours - recommendations may be inaccurate Reduce your overall MySQL memory footprint for system stability Increasing the query_cache size over 128M may reduce performance Temporary table size is already large - reduce result set size Reduce your SELECT DISTINCT queries without LIMIT clauses Variables to adjust: *** MySQL's maximum memory usage is dangerously high *** *** Add RAM before increasing MySQL buffer variables *** query_cache_size (> 256M) [see warning above] Thanks in advanced for your help!

    Read the article

  • VMware guest pauses when the host is idle - how do I keep it running?

    - by EMP
    I'm running VMWare Worstation 7 with Windows 7 x64 as guest, Windows XP x64 as host. Inside the guest I run a long-running console application, which prints out progress messages with timestamps on them. Sometimes I leave it running for several hours while I lock the host OS and don't touch the computer at all. When I come back I find that some time after I left it seems to have paused and automatically resumed: the console app hasn't made much progress and there's a large time gap in its progress messages. There's nothing relevant in the host event log, but in the guest Application event log I can see these messages around the time I left: A request to disable the Desktop Window Manager was made by process (VMware Tools Service) The Desktop Window Manager was unable to start because composition was disabled by a running application And later, around the time I returned, this shows up in the System log: The system time has changed to ?2012?-?01?-?12T06:36:46.921000000Z from ?2012?-?01?-?12T03:18:19.953079000Z. That seems to support my theory that it's VMware doing something and not Windows itself. The question is: how do I stop it doing that? I want my application to continue running. By the way, the power options are set to never sleep in both guest and host.

    Read the article

  • Windows won't boot after moving house. How do I solve this?

    - by James
    Ive just moved house and tried to set up my desktop after packing it away and now when I power it on, the BIOS boots up and no errors are found but when my computer tires to boot into Windows 7 a continuous fast beeping sound is made and a black screen is displayed. What I've done so far: Reset to UEFI defauts Played about with RAM, I had 4*4 GB sticks, I took all of them out to test for a mobo error which I have and now im only using 1 stick of 4 GB. Changed my GPU, I tok my gtx580 out and now im using the onboard Intel 3000 graphics driver, the BIOS and uefi are correctly displaying so I no longer think its a GPU based error. Ive check all of the connections and nothing seems to be loose. My HDD setup is: 2 128 GB SSD's in Raid 0 as my main C drive (possibly cause of error?) 1 1 TB Games drive 1 2 TB Data Drive Ive also got a blueray drive connected. After searching the internet im pretty much out of suggestions but im currently downloading a live CD to see if it will boot and if I can access some files on my HDD.

    Read the article

  • HP/IBM alternative to Buffalo iSCSI TerraStation?

    - by Robin Day
    I'm looking at virtualising some of our infrastructure in order to allow for more resiliance and future expandability. We have successfully virtualised on single servers with Direct Attached Storage and are now looking for a more future proof solution using a high powered host (or two) and a SAN (or two). I'm thinking that the host machine will probably be an HP ProLiant DL360 G7 (all of our exisiting infrastructure is HP). Unfortunately, I am new to the world of SANs. From what I can see, the Buffalo Terrastation III is all I would need in order to setup an iSCSI SAN for VMWare to use. However, I'm a little reticent to go that way as it's a bit too "entry level" for my liking. In particular I would be very keen for more redundancy, power, networking, etc. I'm also very aware that you "get what you pay for". Therefore, can anyone reccommend equivalents from the big boys? HP/IBM? I have searched high and low on the HP site and seen many options but am struggling to work out if it is all the hardware I will need. Some options appear to need separate controllers from disk enclosures, etc.

    Read the article

  • Chrome Lockups Windows 7 64-bit

    - by Mike Chess
    I'm running Google Chrome (6.0.427.0 dev) on Windows 7 Home Premium 64-bit (AMD Phenom 3.00 GHz, 8 GB RAM). The computer lockups hard after running Chrome for about five minutes. The lockup happens whether Chrome is actually being used to browse web sites or it is just idling. No programs can be started or interacted with when this happens. The computer must be power-cycled to recover. The lockup happens regardless of which web sites are being browsed. The system event logs do not show any events around the time when the lockup transpired. All other applications run just fine on this system. In fact, Chrome ran without issue for several months on this system (the system was brand new 03-2010). I also run the same version of Chrome on other computers (Windows XP SP3) without issue. I've come to really like Chrome and use it as my default browser whenever possible. What could be causing Chrome to cause the system to lockup as it does? Does Chrome have any logs that aren't part of the Windows event log? Does Chrome have a debug command line switch that might reveal more about what happens?

    Read the article

  • Why is my Toshiba Satellite L675D laptop not connecting to my HD TV using an HDMI cord?

    - by Akasha Eyre
    I'm having a problem connecting my Toshiba Satellite L675 laptop to my Samsung HD TV. I've done it before using an HDMI cord but now, for some odd reason, it's not connecting at all. My computer screen before would go completely black for a second & then come back & (with it being attached to the TV with the HDMI cord & it being on the proper channel) it would make a sound, come on & work beautifully. Now, I try hooking it up & it doesn't do anything. No black screen, no sound. The TV screen just says there's no connection & that I need to check out the power source. I'm still checking around, trying to find out if there's a virus in my computer (since my dad & I have the same computer & he can connect his to the TV with no problems), or if I deleted something that had to do with the connection. I've tried turning my computer off & letting it sit for a while, I've tried checking out other websites & have come up with nothing.

    Read the article

  • PC in POST loop

    - by Antony Scott
    Hi, I have a custom built PC using a Gigabyte GA-EP35-DS3P motherboard with a Q6600 CPU. For the last 2 days it has got itself stuck into a POST loop. Saying that, I don't think it actually got in to the BIOS. It repeatedly lit up the LEDs and then not much more. Sometimes I could see the CPU fan twitch. Today I re-seated the DIMMs and it powered up straight away. Could this be a sign of an impending hardware failure? The PC is hooked up to a UPS, so I don't think it's a power spike or anything like that, as I have 2 other PCs on the same UPS and they're both fine. Yesterday, the first time this happened, I was getting a message which I think said "Scanning BIOS image on hard drive". I've been building and using PCs for well over 25 years and that's a new one on me! I don't think it's an over heating problem, as when the PC does finally boot up the CPU is running at 35-40C. Any help or suggestions would be greatly appreciated.

    Read the article

  • Periodic internet connection drops

    - by user9647
    My setup is a dsl modem, and a dlink di 524M router. I'm also using a Witopia VPN which runs through OpenVPN. I've been having trouble with the internet connection dropping very frequently. It comes back shortly, without even a router/modem/computer restart. This happens as frequently as every ten minutes. Occasionally (not often) it will last as long as an hour or two without dropping. When it drops, I can get it back almost immediately by clicking Reconnect in the OpenVPN GUI and letting that do it's thing. It's worth noting that I'm in China. Calling support is a bit difficult because of that. Also I don't really understand all of the router's software, although I've got it generally figured out. I've tried a bunch of stuff, attempts to diagnose and/or fix the problem. No success with any of the following: I've power cycled both the modem and the router. I've tried an ethernet connection to the router. I've connected without the VPN. I've disabled IEEE authentication on all connections. I've checked for viruses. I've tried lifting it off the ground so as to prevent overheating.

    Read the article

  • How to disable monitor auto detection in Windows 7?

    - by Jay Yother
    I am currently running Windows 7 Ultimate 64-bit with a dual monitor setup with an NVIDIA 7950 GT graphics card. One monitor is dedicated to this machine and the other monitor is connected to a DVI KVM switch. When I switch to my other computer, Windows 7 disables the monitor. However, when I switch back it does not re-enable the monitor. The only circumstance that automatically re-enables the second monitor is when I switch back after Windows has put the monitors into power save mode. I am continually having to bring up the NVIDIA control panel to have it re-enable the monitor. Under Windows XP I would just disable the NVIDIA service to prevent it from auto-detecting the monitor (which doesn't solve the problem under Win7), and in Vista there was a registry hack that would prevent this. It looks as though that has been removed in Windows 7. I have found similar questions posted on this site, but nothing that matches my problem exactly. The following link is the question that comes the closest, but does not provide a solution to the problem. http://superuser.com/questions/96683/how-to-fix-monitor-detection-on-windows-7 Is there a way in Windows 7 to disable monitor auto-detection? Update: I just added a second graphics card to my Windows 7 64-bit machine. I plugged one monitor into each graphics card. Now, when I use the KVM switch to switch back and forth it will re-enable the second monitor like it should. There are however, a few quirks with this. If I have a program maximized on the second monitor and it has focus, when I switch it will move to monitor 1. If I have a program maximized on the second monitor and it does not have focus, when I switch it will behave like it is minimized and when I bring it back up it will show up maximized on monitor 1. Definitely better than it was, but still looking for a way to disable the auto-detection.

    Read the article

  • Buying an old laser printer -- what will need to be replaced?

    - by marienbad
    Hi all -- as you can see I'm new. I do IT and wiring for a small local shop but I never deal with printers. I do a LOT of printing, and I'd like to stop spending as much money on it. On my local CL, there is an HP 8100DN (duplex network) printer for a very good price (and the toner is a quarter-cent per page). It has printed 200,000 pages and I don't yet know anything else about it. The model was released in 1999. So my questions: What are the parts that tend to need service on laser printers? On ebay, I see fusers, rollers, DC power boards, and motors. What would you expect to replace soon at 200,000 pages? Are there any good "tests" to find out if certain parts are near failure? Do you have anything to say about the HP 8100 specifically? The bottom line for me is that if there's any chance of repairs costing more than $100, it's not worth it for me.

    Read the article

  • How to resolve 'No internet connectivity issues' with a Virtualised 2008 R2 Server using Forefront UAG

    - by user684589
    I have spent some considerable time reading up on as many possible blogs and articles as I can to help me solve why my VM (Running on Hyper-V) for DirectAccess has suddenly stopped being able to access the internet. The VM setup shares the same internet connection on which I have written and submitted this question so I know that the actual underlying internet connection is fully functional. Previous to last week the DirectAccess was fully functional and had no issues. This is a recent problem which was led up to by a number of consistent crashes on the DA machine when access was attempted. Upon reboot all seemed well until recently. I am not certain whether it is relevant, but previously to this I had a number of power issues where the entire VM host shutdown unexpectedly leaving around 8 VM's in a bad way. Upon restart, the UAG DirectAccess machine was unable to access its configuration service (although the service was started) but this seemed to relate to the Light-Weight Active Directory Service AD LDS which had a corrupted database. Having repaired this database, I restarted the service and could subsequently reconnect to the configuration service again. For good measure I re-bound the network adapters (virtualised through Hyper-V) and DirectAccess claimed to be all happy again. However as it stands my machine is still unable to access the internet showing the "No internet connectivity" exclamation mark for the external facing NIC. I have also tried removing the adapters, disabling, re-enabling and the problem persists. The intranet part of the VM CorpNet seems to be fully functional as before and I'm running out of ideas. Any input would be greatly appreciated. I am not an advanced Domain Administrator so please be gentle.

    Read the article

  • Computer won't start up. Stuck on Lenovo splash screen. Help Diagnose

    - by Ace Legend
    I have some (I'm not sure exactly what model) Lenovo 21" IdeaCentre. Honestly, the computer works off and on. I have had problems with it not being able to shutdown, which I fixed. The fan seems to be constantly running, a few other problems as well. Anyway, nobody was using it when all of a sudden it switched to a blue screen. I was in the kitchen, but when I got over to the computer I read the message. It said something about bad drivers, but that is all I saw and then it restarted. However, when it got to the Lenovo Splash screen, nothing happened. I waited there for over 10 minutes, but still nothing. I tried to turn of the computer, but the only way to do it was to pull out the power cable. I then removed all USB devices and tried again. Still nothing. It also won't respond to keyboard input when I try to use enter to interrupt normal startup. My guess is some piece of hardware is damaged inside the machine. However, I have no idea what piece it is. Does anybody have any idea what could be wrong with it? Thanks.

    Read the article

  • Proper approach to debug PC startup problems (POST)

    - by saurabhj
    My CPU was heating up to around 65 deg C and last time this had happened (about a year ago), I got thermal paste put between the CPU and heat sink and this managed to get it down to about 45 - 50 degrees. This time, I got some thermal paste and put it myself. However, my PC is not showing the POST display and not starting up. This is what happens LEDs light up HDDs spin Mouse is getting power All fans including the processor fan starts No display on monitor No diagnostic beep sounds (no sounds at all) What I have tried Removing everything including RAM, HDD, PCI cards, AGP card Boot up machine No changes from first state. What steps can I take to figure out where the problem lies? Note (might be important) When I removed the heat sink, the processor came out with it (it was stuck to it inspite of the processor latch on) Had to pry it separate with a screw-driver. Configuration Pentium 4, 2.8 Ghz with HT (very old, I know) Original Intel Mobo with onboard sound and graphics (GB series) 2x512 Mb DDR-RAM 2 SATA disks (320 Gigs / 250 gigs) DVD Writer Creative Sound Card Network card Any help would be appreciated. Thanks!

    Read the article

  • Servers - Buying New vs Buying Second-hand

    - by Django Reinhardt
    We're currently in the process of adding additional servers to our website. We have a pretty simple topology planned: A Firewall/Router Server infront of a Web Application Server and Database Server. Here's a simple (and technically incorrect) diagram that I used in a previous question to illustrate what I mean: We're now wondering about the specs of our two new machines (the Web App and Firewall servers) and whether we can get away with buying a couple of old servers. (Note: Both machines will be running Windows Server 2008 R2.) We're not too concerned about our Firewall/Router server as we're pretty sure it won't be taxed too heavily, but we are interested in our Web App server. I realise that answering this type of question is really difficult without a ton of specifics on users, bandwidth, concurrent sessions, etc, etc., so I just want to focus on the general wisdom on buying old versus new. I had originally specced a new Dell PowerEdge R300 (1U Rack) for our company. In short, because we're going to be caching as much data as possible, I focussed on Processor Speed and Memory: Quad-Core Intel Xeon X3323 2.5Ghz (2x3M Cache) 1333Mhz FSB 16GB DDR2 667Mhz But when I was looking for a cheap second-hand machine for our Firewall/Router, I came across several machines that made our engineer ask a very reasonable question: If we stuck a boat load of RAM in this thing, wouldn't it do for the Web App Server and save us a ton of money in the process? For example, what about a second-hand machine with the following specs: 2x Dual-Core AMD Opteron 2218 2.6Ghz (2MB Cache) 1000Mhz HT 16GB DDR2 667Mhz Would it really be comparable with the more expensive (new) server above? Our engineer postulated that the reason companies upgrade their servers to newer processors is often because they want to reduce their power costs, and that a 2.6Ghz processor was still a 2.6Ghz processor, no matter when it was made. Benchmarks on various sites don't really support this theory, but I was wondering what server admin thought. Thanks for any advice.

    Read the article

< Previous Page | 667 668 669 670 671 672 673 674 675 676 677 678  | Next Page >