Search Results

Search found 19157 results on 767 pages for 'shared folder'.

Page 671/767 | < Previous Page | 667 668 669 670 671 672 673 674 675 676 677 678  | Next Page >

  • SharePoint Records Center Submitted E-mail Records not picked up

    - by Kenneth Verburg
    We have set up a new SharePoint 2007 site with a Records Repository. We're using Exchange 2007 Managed Folders to route e-mails to this repository based on the 'label' attached to the e-mail as set in the Exchange 2007 journaling options. E-mails added to a Managed Folder get sent to SharePoint, they end up in the "Submitted E-mail Records" list of the Records Repository. That's according to plan, but the e-mails are not routed to the respective document library as defined by the label. Instead an error appears in the event viewer for every e-mail listed in the Submitted E-mail Records list, on every interval of the records repository schedule (set to every two minutes for testing purposes): Value cannot be null, parameter name: g. Sending a document from the SharePoint site iself to the Records Repository via the Send To... link works fine, but e-mails get stuck in the list... We have set Document Libraries in the Respository with and without content types (with matching names with the Label and the Record Routing rule set). Any ideas what could be wrong? This is in the event log: Every two minutes the following error appears in the Application Log: Source: Office SharePoint Server Category: Records Center Type: Error Event ID: 4975 User: N/A Computer: SPS2007 Description: Value cannot be null. Parameter name: g For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp.

    Read the article

  • How to use Zune software to listen to podcasts with generic MP3 player?

    - by Bevan
    I listen to a bunch of podcasts - a great way to fill the otherwise mindless space of a daily commute. My MP3 player is a Transonic brand, appears on my computer as a generic storage device. I've been using iTunes to download the podcasts, and manually moving the files out of the disk folder onto my player, but this is pretty tedious. iTunes also fails to recognise that the files are gone and leaves them in the list. (Actually, iTunes for windows is pretty much a dog, but that's a different rant.) The Zune software is 99% of what I want in a podcast downloader - performs well, looks nice, downloads reliably and so on. Some features - like only downloading the next five unheard episodes of a podcast - are superb. However, if I manually move the files across to the MP3 player, the Zune software concludes that the file has never been downloaded, and downloads it again. This leads me to my question: What is a good way to use the Zune software to download podcasts for listening on a generic MP3 player? Are there any addons for the Zune software to make this easier? Registry hacks? Can I configure the Zune software to not download the same episode multiple times? Is there a way for the Zune software to populate my MP3 player directly, instead of having to copy files?

    Read the article

  • Backup a hosted Sharepoint

    - by David Mackintosh
    One of my customers has outsourced their Sharepoint and Exchange services to a hosted services provider. I believe it is a Sharepoint 2007 service. It is a shared hosting solution, so we do not have any kind of access to the server itself; we only have user-level and sharepoint-administrator-level access to the Sharepoint application. They have come to the point where they would like to have a copy of everything that is on the Sharepoint server. I have downloaded the Office Sharepoint Designer 2007, and it features three (!) ways to backup a Sharepoint server, none (!) of which work for me: File-Export-Personal Web Package: When selecting everything, it calculates a negative size. Barfs with No "content-type" in CGI environment error. File-Export-Sharepoint Template: barfs with a A World Wide Web browser, such as Windows Internet Explorer, is required to use this feature error. Site-Administration-Backup Web Site: wants to create the backup .cmp file on the sharepoint server itself. I don't have access to any servers on the same network so I can't redirect it to any form of the suggested \\server\place. Barfs with a The Web application at $URL could not be found. [...] error. Possibly moot because Google tells me that bad things happen using OSD to back up sites larger than 24MB (which this site is most definitely). So I called the helpdesk of the outsource provider, and got told that they recommend using OSD, but no they don't actually provide any application support for OSD (not that I blame them for that), but they could do a stsadm.exe backup and provide us with that, and OSD should be able to read the resulting cmp file. Then for authorization reasons they had my customer call them directly (since I can't authorize such an operation), and they told him that he didn't want a stsadm.exe backup, he wanted to get into an 'explorer view' and deal with things that way (they were vague). Google hasn't been much help in figuring out what an 'explorer view' is, let alone how I bring one up. The end goal of this operation is to have a backup of the site as it exists (hopefully today, but shortly anyways) in such a format that we don't need another sharepoint server to restore it to. Ie we'd like to be able to pick individual content directly out of this backup. We are not excessively concerned with things like formatting. We just want the documents. This is a fairly complex site with multiple subsites and multiple folders per subsite, so sitting there and manually downloading each file isn't really going to happen if there is a better easier way. So, my questions: Is the stsadm.exe backup what I want? If not, what do I want? If I manage to convince them that I do want the stsadm.exe backup, can I pick files out of the resulting backup file with OSD? If OSD isn't going to let me extract individual files, is there a tool I can use that can?

    Read the article

  • Robocopy failure with Windows Server 2008 Scheduled Task

    - by CC
    So I have a batch script for robocopy. Running this from the command line does exactly what I want. robocopy "D:\SQL Backup" \\server1\Backup$\daily /mir /s /copyall /log:\\lmcrfs4g\NavBackup$\robocopyLog.txt /np Then I create a Scheduled Task in Windows Server 2008. If I set up the task to use my Domain Admin account, great. But I'm trying to get it to run as a separate domain account for Scheduled Tasks. If I use that account, folders get created, but files aren't copied. I get the following error: 2011/02/17 15:41:48 ERROR 1307 (0x0000051B) Copying NTFS Security to Destination Directory D:\SQL Backup\folder\ This security ID may not be assigned as the owner of this object. I've verified my domain\Scheduled Tasks account has Full Control NTFS permissions on both the source and destination, and the Full Control Sharing on my hidden \server1\backup$ share. Just for giggles, I've tried adding the domain account to the local Administrators group on both servers. This works fine, but that seems like a lot of privileges just to copy files. Any ideas on what I'm missing?

    Read the article

  • procmail don't execute php script

    - by Phliplip
    Hi, I have setup a kannel SMS gateway on my FreeBSD 7.2 - the service works great. I'm now trying to setup a email2sms feature. For this i have created a system user called kannel and all mails are forwarded to this user. In the home dir of kannel i have the following files. -rw-r--r-- 1 kannel kannel 81B 17 jan 09:50 .procmailrc lrwxr-x--- 1 root kannel 58B 14 jan 13:24 email2sms.php @ -> some-what-some-where -rw-rw-rw- 1 root kannel 5,8K 17 jan 09:52 log.email2sms -rw------- 1 kannel kannel 1,3K 17 jan 09:50 procmail.log -rw-r----- 1 root kannel 606B 14 jan 13:28 rawmail.txt The file email2sms.php is a symlink to the a php script (ZendFramework Application) that takes the email from STDIN, and uses ZendFramework to parse that mail into an object. It then do a http request to the SMS gateway. The php-script works. Content of .procmailrc LOGFILE=$HOME/procmail.log VERBOSE=yes :0 | php email2sms.php >> log.email2sms From last sent email i have this in procmail.log procmail: [97744] Mon Jan 17 09:50:40 2011 procmail: [97744] Mon Jan 17 09:50:40 2011 procmail: Assigning "LASTFOLDER= php email2sms.php >> log.email2sms" procmail: Executing " php email2sms.php >> log.email2sms" procmail: Notified comsat: "kannel@:/home/user/kannel/ php email2sms.php >> log.email2sms" From [email protected] Mon Jan 17 09:50:40 2011 Subject: asdf as Folder: php email2sms.php >> log.email2sms 2600 But there is no new output to log.email2sms, and the script should output the subject of the email. If i sudo as the kannel user and pipe a file with raw email to the script, it executes just fine. [root@webserver /home/user/kannel]# /home/user/kannel/ sudo -u kannel cat rawmail.txt | php email2sms.php >> log.email2sms And the command outputs to log.email2sms as desired. Any ideas guys?

    Read the article

  • Integration of SharePoint 2010 with TFS2010

    - by Kabir Rao
    We have performed following steps as of now- Install TFS2010 10.0.30319.1 (RTM) on Windows Server 2008 R2 Enterprise(app tier) SQL 2008 SP1 with Cumulative update 2 on Windows Server 2008 R2 Enterprise(data tier) Reporting Service is installed on app tier. After this installation worked fine we installed SharePoint 2010 on app tier. After installation we followed http://blogs.msdn.com/b/team_foundation/archive/2010/03/06/configuring-sharepoint-server-2010-beta-for-dashboard-compatibility-with-tfs-2010-beta2-rc.aspx for configuration. We are not able to perform the last step described in the link as following error occured- TF249063: The following Web service is not available: http://apptier:31254/_vti_bin/TeamFoundationIntegrationService.asmx. This Web service is used for the Team Foundation Server Extensions for SharePoint Products. The underlying error is: The remote server returned an error: (404) Not Found.. Verify that the following URL points to a valid SharePoint Web application and that the application is available: http://apptier:31254. If the URL is correct and the Web application is operating normally, verify that a firewall is not blocking access to the Web application. We have also noticed that Document Folder in Team project also have red x. Please help. Thanks upfront.

    Read the article

  • Win 2008 R2 - copying TO disk is very slow, copying FROM is more or less okay

    - by avs099
    I have Windows 2008 R2 SP1 with 4 identical SATA disks (Seagate Barracude 7200) in RAID 5 array. It has 4Gb of memory; all recent updates are installed. Problem: when I copy large file from one folder to another, I get about 10MB/s average speed. When I read this file from network share via 1Gbps connection - I get about 25-30 MB/s. Both numbers seems to be low for me - but specifically I'm very frustrated with low write speed. there is no antivirus, no hyper-v, it's just a fileserver - i when i do my tests nobody else reads/write from it (we have only 4 people in a team, so I'm sure). Not sure if that matters, but there is only 1 logic disk "C" with all available space (1400 GB). I'm not an admin at all, so I have no idea where to look and what other information to provide. I did run performance monitor with "% idle time", "avg bytes read", "avg byte write" - here is the screenshot: I'm not sure why there are such obvious spikes. Any idea? Please let me know if you need me to provide more information - what counters should I check, etc. I'm very eager to get this solved. Thank you. UPDATE: we have another Windows 2008 R2 SP1 server with 2 RAID1 arrays - one is disk C (where windows is installed, another one is disk E). It is running Hyper-V and does not have antivirus. I noticed the following behavior when I copy large file (few GBs): C - C: about 50MB/sec C - E: about 55MB/sec E - E: 8MB/sec!!! E - C: 8MB/sec!!! what could cause this?? E drive is RAID1 array from same Seagate Barracuda 1TB drives..

    Read the article

  • User directive in nginx generates error despite running as UID root

    - by Joost Schuur
    I'm running nginx on a MacOS X machine, installed with brew, and when I launch nginx, even with sudo, I get the following warning in my log file over and over again: 4/21/11 2:03:42 AM org.nginx[3788] nginx: [warn] the "user" directive makes sense only if the master process runs with super-user privileges, ignored in /usr/local/etc/nginx/conf/nginx.conf:2 From nginx.conf: user jschuur staff; I'm already launching nginx with sudo, since I want the thing to listen on port 80. Shouldn't that be enough to give it the proper super user privileges? The nginx binary as it's installed: jschuur@Glenna:sbin ? master ls -la total 4544 drwxr-xr-x 3 jschuur staff 102 Apr 12 20:53 . drwxrwxr-x 15 jschuur staff 510 Apr 12 15:25 .. -rwxr-xr-x 1 jschuur staff 2325648 Apr 12 20:39 nginx FWIW, I recompiled the binary to set passenger up and moved it around from it's original location into /usr/local/sbin. Update: As it turns out MacOS X was restarting nginx after I'd stopped it, because the launchd plist in ~/Library/LaunchAgents had set it to 'KeepAlive'. However, because I installed this plist into my local user's LaunchAgents folder as opposed to /Library/LaunchAgents (or better yet /Library/LaunchDaemons, which run before you even log on), it wasn't executed as root. Because of an error about not having permissions to use port 80, it actually exited right away, but still wrote to the same log file as the nginx process I started with sudo. I had thought the errors stemming from the automatic restart were actually coming from my manual restart via sudo. So, bottom line, problem solved. The real problem here was the homebrew instructions specifically asking you to install the plist file into an area that wouldn't allow a local site to use port 80.

    Read the article

  • How to hide subfolder when using Web.config for subdomains?

    - by mc-kay
    I have FTP access to my ASP.NET Websapce (IIS 7) and I route subdomains with a Web.config in the web root folder. She looks like this: <?xml version="1.0" encoding="UTF-8"?> <configuration> <system.webServer> <rewrite> <rules> <rule name="route www and emtpy requests" stopProcessing="true"> <match url=".*" /> <conditions logicalGrouping="MatchAll" trackAllCaptures="false"> <add input="{HTTP_HOST}" pattern="^(www.)?example.com" /> <add input="{PATH_INFO}" pattern="^/www/" negate="true" /> </conditions> <action type="Rewrite" url="\www\{R:0}" /> </rule> <rule name="route to blog" stopProcessing="true"> <match url=".*" /> <conditions logicalGrouping="MatchAll" trackAllCaptures="false"> <add input="{HTTP_HOST}" pattern="^blog.example.com$" /> <add input="{PATH_INFO}" pattern="^/blog/" negate="true" /> </conditions> <action type="Rewrite" url="\blog\{R:0}" /> </rule> </rules> </rewrite> </system.webServer> </configuration> As you can see i have two folders in my root directory: "www" and "blog". When i now enter "blog.example.com" everythink is working fine, but when i click a link i will go to "blog.example.com/blog" What can I do to prevent this behavior ?

    Read the article

  • Is there any way to send Outlook meeting requests from a non-default calendar?

    - by rbeier
    Hi, We have a user with two Outlook accounts. [email protected] is of type Exchange; [email protected] is of type IMAP/SMTP. Both are actually on our Exchange server; but since an Outlook profile can only have one Exchange account, the second one is set up as IMAP. The user would like to send a meeting request from her xyz.com account, so the "from" address appears as [email protected]. Unfortunately that doesn't work. If she creates the meeting in her xyz.com calendar, the meeting request still goes out through her Exchange account, [email protected]. The meeting request "compose message" window has an Account dropdown below the Send button, but this has no effect. Before she sends the invitation, a warning appears: "Responses to this meeting request will not be tallied because this meeting is not in your main Calendar folder. Is this OK?" Is there any workaround for this? We're using Outlook 2007 and Exchange 2003 SP2. Thanks, Richard

    Read the article

  • Git fails to push with error 'out of memory'

    - by jwir3
    I'm using gitosis on a server that has a low amount of memory, specifically around 512 MB. When I try to push a large folder (happens to be a backup from an android phone), I get: me@corellia:~/Configs/$ git push origin master Counting objects: 18, done. Delta compression using up to 8 threads. Compressing objects: 100% (14/14), done. fatal: Out of memory, malloc failed MiB | 685 KiB/s error: pack-objects died of signal 13 error: failed to push some refs to 'git@dagobah:Configs' I've been searching the web, and notably found: http://www.mail-archive.com/[email protected]/msg01747.html as well as http://git.661346.n2.nabble.com/Out-of-memory-error-during-git-push-td5443705.html but these don't seem to help me for two reasons: 1) I am not actually out of memory when I push. When I run 'top' during the push, I get: 24262 git 18 0 16204 6084 1096 S 2 1.2 0:00.12 git-unpack-obje Also, during the push if I run /head/meminfo, I get: MemTotal: 524288 kB MemFree: 289408 kB Buffers: 0 kB Cached: 0 kB SwapCached: 0 kB Active: 0 kB Inactive: 0 kB HighTotal: 0 kB HighFree: 0 kB LowTotal: 524288 kB So, it seems that I have enough memory free, but it's actually still failing, and I'm not enough of a git guru to figure out what is happening. I would appreciate it if someone could give me a hand here and tell me what could be causing this problem, and what I can do to solve it. Thanks! EDIT: The output of running the ulimit -a command: scottj@dagobah:~$ ulimit -a core file size (blocks, -c) 0 data seg size (kbytes, -d) unlimited scheduling priority (-e) 0 file size (blocks, -f) unlimited pending signals (-i) 204800 max locked memory (kbytes, -l) 32 max memory size (kbytes, -m) unlimited open files (-n) 1024 pipe size (512 bytes, -p) 8 POSIX message queues (bytes, -q) 819200 real-time priority (-r) 0 stack size (kbytes, -s) 10240 cpu time (seconds, -t) unlimited max user processes (-u) 204800 virtual memory (kbytes, -v) unlimited file locks (-x) unlimited

    Read the article

  • Performance associated with storing millions of files on NTFS

    - by Tim Brigham
    Does anyone have a method / formula, etc that I could use - hopefully based on both current and projected numbers of files - to project the 'right' length of the split and the number of nested folders? Please note that although similar it isn't quite the same as Storing a million images in the filesystem. I'm looking for a way to help make the theories outlined more generic. Assumptions I have 'some' initial number of files. This number would be arbitrary but large. Say 500k to 10m+. I have considered the underlying physical hardware disk IO requirements that would be necessary to support such an endeavor. Put another way As time progresses this store will grow. I want to have the best balance of current performance and as my needs increase. Say I double or triple my storage. I need to be able to address both current needs and projected future growth. I need to both plan ahead and not sacrifice too much of current performance. What I've come up with I'm already thinking about using a hash split every so many characters to split things out across multiple directories and keeping the trees even, very similar as outlined in the comments in the question above. It also avoids duplicate files, which would be critical over time. I'm sure that the initial folder structure would be different based on what I've outlined, and depending on the initial scale. As far as I can figure there isn't a one size fits all solution here. It would be horrendously time intensive to work something out experimentally.

    Read the article

  • apache2.2 + php5 , process never die and stay blocked to LOCK_SH

    - by Givre
    Server version: Apache/2.2.22 (Unix) Server built: Mar 28 2012 16:31:45 Server's Module Magic Number: 20051115:30 Server loaded: APR 1.4.6, APR-Util 1.4.1 Compiled using: APR 1.4.6, APR-Util 1.4.1 Architecture: 64-bit Server MPM: Prefork threaded: no forked: yes (variable process count) Server compiled with.... -D APACHE_MPM_DIR="server/mpm/prefork" -D APR_HAS_SENDFILE -D APR_HAS_MMAP -D APR_HAVE_IPV6 (IPv4-mapped addresses enabled) -D APR_USE_SYSVSEM_SERIALIZE -D APR_USE_PTHREAD_SERIALIZE -D SINGLE_LISTEN_UNSERIALIZED_ACCEPT -D APR_HAS_OTHER_CHILD -D AP_HAVE_RELIABLE_PIPED_LOGS -D DYNAMIC_MODULE_LIMIT=128 -D HTTPD_ROOT="/opt/apache2" -D SUEXEC_BIN="/opt/apache2/bin/suexec" -D DEFAULT_PIDLOG="logs/httpd.pid" -D DEFAULT_SCOREBOARD="logs/apache_runtime_status" -D DEFAULT_LOCKFILE="logs/accept.lock" -D DEFAULT_ERRORLOG="logs/error_log" -D AP_TYPES_CONFIG_FILE="conf/mime.types" -D SERVER_CONFIG_FILE="conf/httpd.conf" Php5.2.17. Using mod_php5 as a DSO module compiled Problem: On shared webhosting, a lot of apache2 process never stop or die and they waiting as long as apache2 restart. Strace of one of theses process: access("tmp/meta_cache.txt", F_OK) = 0 getcwd("/home/exemple.com/htdocs"..., 4096) = 34 lstat("/var", {st_mode=S_IFDIR|0755, st_size=4096, ...}) = 0 lstat("/var/www", {st_mode=S_IFDIR|0755, st_size=4096, ...}) = 0 lstat("/home", {st_mode=S_IFDIR|0755, st_size=1715, ...}) = 0 lstat("/home/exemple.com", {st_mode=S_IFDIR|0755, st_size=16, ...}) = 0 lstat("/home/exemple.com/htdocs", {st_mode=S_IFDIR|0770, st_size=51, ...}) = 0 lstat("/home/exemple.com/htdocs/tmp", {st_mode=S_IFDIR|0777, st_size=51, ...}) = 0 lstat("/home/exemple.com/htdocs/tmp/meta_cache.txt", {st_mode=S_IFREG|0666, st_size=8901, ...}) = 0 lstat("/var", {st_mode=S_IFDIR|0755, st_size=4096, ...}) = 0 lstat("/var/www", {st_mode=S_IFDIR|0755, st_size=4096, ...}) = 0 lstat("/home", {st_mode=S_IFDIR|0755, st_size=1715, ...}) = 0 lstat("/home/exemple.com", {st_mode=S_IFDIR|0755, st_size=16, ...}) = 0 lstat("/home/exemple.com/htdocs", {st_mode=S_IFDIR|0770, st_size=51, ...}) = 0 lstat("/home/exemple.com/htdocs/tmp", {st_mode=S_IFDIR|0777, st_size=51, ...}) = 0 lstat("/home/exemple.com/htdocs/tmp/meta_cache.txt", {st_mode=S_IFREG|0666, st_size=8901, ...}) = 0 lstat("/var", {st_mode=S_IFDIR|0755, st_size=4096, ...}) = 0 lstat("/var/www", {st_mode=S_IFDIR|0755, st_size=4096, ...}) = 0 lstat("/home", {st_mode=S_IFDIR|0755, st_size=1715, ...}) = 0 lstat("/home/exemple.com", {st_mode=S_IFDIR|0755, st_size=16, ...}) = 0 getcwd("/home/exemple.com/htdocs"..., 4096) = 34 lstat("/var", {st_mode=S_IFDIR|0755, st_size=4096, ...}) = 0 lstat("/var/www", {st_mode=S_IFDIR|0755, st_size=4096, ...}) = 0 lstat("/home", {st_mode=S_IFDIR|0755, st_size=1715, ...}) = 0 lstat("/home/exemple.com", {st_mode=S_IFDIR|0755, st_size=16, ...}) = 0 lstat("/home/exemple.com/htdocs", {st_mode=S_IFDIR|0770, st_size=51, ...}) = 0 lstat("/home/exemple.com/htdocs/tmp", {st_mode=S_IFDIR|0777, st_size=51, ...}) = 0 lstat("/home/exemple.com/htdocs/tmp/meta_cache.txt", {st_mode=S_IFREG|0666, st_size=8901, ...}) = 0 open("/home/exemple.com/htdocs/tmp/meta_cache.txt", O_RDONLY) = 10905 fstat(10905, {st_mode=S_IFREG|0666, st_size=8901, ...}) = 0 lseek(10905, 0, SEEK_CUR) = 0 flock(10905, LOCK_SH) = The process never die, and stay like this. All files are on NFS V3 I'dont know how to solve this problem or find more informations. The effect is that all apache2 process become used and apache2 crash totaly . Thanks for you help.

    Read the article

  • hostapd running on Ubuntu Server 13.04 only allows single station to connect when using wpa

    - by user450688
    Problem Only a single station can connect to hostapd at a time. Any single station can connect (W8, OSX, iOS, Nexus) but when two or more hosts are connected at the same time the first client loses its connectivity. However there are no connectivity issues when WPA is not used. Setup Linux (Ubuntu server 13.04) wireless router (with separate networks for wired WAN, wired LAN, and Wireless LAN. iptables-save output: *nat :PREROUTING ACCEPT [0:0] :INPUT ACCEPT [0:0] :OUTPUT ACCEPT [0:0] :POSTROUTING ACCEPT [0:0] -A POSTROUTING -s 10.0.0.0/24 -o p4p1 -j MASQUERADE -A POSTROUTING -s 10.0.1.0/24 -o p4p1 -j MASQUERADE COMMIT *mangle :PREROUTING ACCEPT [13:916] :INPUT ACCEPT [9:708] :FORWARD ACCEPT [4:208] :OUTPUT ACCEPT [9:3492] :POSTROUTING ACCEPT [13:3700] COMMIT *filter :INPUT DROP [0:0] :FORWARD DROP [0:0] :OUTPUT ACCEPT [9:3492] -A INPUT -i p4p1 -m state --state RELATED,ESTABLISHED -j ACCEPT -A INPUT -i p4p1 -p tcp -m tcp --dport 22 -m state --state NEW -j ACCEPT -A INPUT -i eth0 -j ACCEPT -A INPUT -i wlan0 -j ACCEPT -A INPUT -i lo -j ACCEPT -A FORWARD -i p4p1 -m state --state RELATED,ESTABLISHED -j ACCEPT -A FORWARD -i eth0 -j ACCEPT -A FORWARD -i wlan0 -j ACCEPT -A FORWARD -i lo -j ACCEPT COMMIT /etc/hostapd/hostapd.conf #Wireless Interface interface=wlan0 driver=nl80211 ssid=<removed> hw_mode=g channel=6 max_num_sta=15 auth_algs=3 ieee80211n=1 wmm_enabled=1 wme_enabled=1 #Configure Hardware Capabilities of Interface ht_capab=[HT40+][SMPS-STATIC][GF][SHORT-GI-20][SHORT-GI-40][RX-STBC12] #Accept all MAC address macaddr_acl=0 #Shared Key Authentication wpa=1 wpa_passphrase=<removed> wpa_key_mgmt=WPA-PSK wpa_pairwise=CCMP rsn_pairwise=CCMP ###IPad Connectivevity Repair ieee8021x=0 eap_server=0 Wireless Card #lshw output product: RT2790 Wireless 802.11n 1T/2R PCIe vendor: Ralink corp. physical id: 0 bus info: pci@0000:03:00.0 logical name: mon.wlan0 version: 00 serial: <removed> width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list logical wireless ethernet physical configuration: broadcast=yes driver=rt2800pci driverversion=3.8.0-25-generic firmware=0.34 ip=10.0.1.254 latency=0 link=yes multicast=yes wireless=IEEE 802.11bgn #iw list output Band 1: Capabilities: 0x272 HT20/HT40 Static SM Power Save RX Greenfield RX HT20 SGI RX HT40 SGI RX STBC 2-streams Max AMSDU length: 3839 bytes No DSSS/CCK HT40 Maximum RX AMPDU length 65535 bytes (exponent: 0x003) Minimum RX AMPDU time spacing: 2 usec (0x04) HT RX MCS rate indexes supported: 0-15, 32 TX unequal modulation not supported HT TX Max spatial streams: 1 HT TX MCS rate indexes supported may differ Frequencies: * 2412 MHz [1] (27.0 dBm) * 2417 MHz [2] (27.0 dBm) * 2422 MHz [3] (27.0 dBm) * 2427 MHz [4] (27.0 dBm) * 2432 MHz [5] (27.0 dBm) * 2437 MHz [6] (27.0 dBm) * 2442 MHz [7] (27.0 dBm) * 2447 MHz [8] (27.0 dBm) * 2452 MHz [9] (27.0 dBm) * 2457 MHz [10] (27.0 dBm) * 2462 MHz [11] (27.0 dBm) * 2467 MHz [12] (disabled) * 2472 MHz [13] (disabled) * 2484 MHz [14] (disabled) Bitrates (non-HT): * 1.0 Mbps * 2.0 Mbps (short preamble supported) * 5.5 Mbps (short preamble supported) * 11.0 Mbps (short preamble supported) * 6.0 Mbps * 9.0 Mbps * 12.0 Mbps * 18.0 Mbps * 24.0 Mbps * 36.0 Mbps * 48.0 Mbps * 54.0 Mbps max # scan SSIDs: 4 max scan IEs length: 2257 bytes Coverage class: 0 (up to 0m) Supported Ciphers: * WEP40 (00-0f-ac:1) * WEP104 (00-0f-ac:5) * TKIP (00-0f-ac:2) * CCMP (00-0f-ac:4) Available Antennas: TX 0 RX 0 Supported interface modes: * IBSS * managed * AP * AP/VLAN * WDS * monitor * mesh point software interface modes (can always be added): * AP/VLAN * monitor valid interface combinations: * #{ AP } <= 8, total <= 8, #channels <= 1 Supported commands: * new_interface * set_interface * new_key * new_beacon * new_station * new_mpath * set_mesh_params * set_bss * authenticate * associate * deauthenticate * disassociate * join_ibss * join_mesh * set_tx_bitrate_mask * set_tx_bitrate_mask * action * frame_wait_cancel * set_wiphy_netns * set_channel * set_wds_peer * Unknown command (84) * Unknown command (87) * Unknown command (85) * Unknown command (89) * Unknown command (92) * testmode * connect * disconnect Supported TX frame types: * IBSS: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 * managed: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 * AP: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 * AP/VLAN: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 * mesh point: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 * P2P-client: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 * P2P-GO: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 * Unknown mode (10): 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 Supported RX frame types: * IBSS: 0x40 0xb0 0xc0 0xd0 * managed: 0x40 0xd0 * AP: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0 * AP/VLAN: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0 * mesh point: 0xb0 0xc0 0xd0 * P2P-client: 0x40 0xd0 * P2P-GO: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0 * Unknown mode (10): 0x40 0xd0 Device supports RSN-IBSS. HT Capability overrides: * MCS: ff ff ff ff ff ff ff ff ff ff * maximum A-MSDU length * supported channel width * short GI for 40 MHz * max A-MPDU length exponent * min MPDU start spacing Device supports TX status socket option. Device supports HT-IBSS.

    Read the article

  • How to backup a NAS drive to a USB drive?

    - by Tim Murphy
    How would you backup 600+ GB of data on a NAS (Network-Attached Storage) drive to a USB external drive? The NAS drive does not contain mission critical data nonetheless I wish to make weekly copies of it just in case. The NAS drive is almost exclusively used as an archive dump and is rarely updated. However the backup strategy used must have a simple restore procedure so I can confidently say the data now on the NAS drive is exactly how it was at the time of backup. I did try xcopy but seemed like it would take many-many hours and eventually crashed with insufficient memory. http://www.ctunion.com/node/114 suggests I would need to use xxcopy instead due to folder/file name lengths. My concern with xcopy/xxcopy is the length of time it takes. Hoping something else is faster. NAS drive is DLink DNS-313. 1TB drive installed. Connected to router via Ethernet cable. USB drive is Seagate 1TB. Can be connected to Windows Vista (preferred) or Windows 7 PCs. Both PCs are usually connected Wirelessly however ethernet cable can be used during backup to speed up the process.

    Read the article

  • publickey authentication only works with existing ssh session

    - by aaron
    publickey authentication only works for me if I've already got one ssh session open. I am trying to log into a host running Ubuntu 10.10 desktop with publickey authentication, and it fails when I first log in: [me@my-laptop:~]$ ssh -vv host ... debug1: Next authentication method: publickey debug1: Offering public key: /Users/me/.ssh/id_rsa ... debug2: we did not send a packet, disable method debug1: Next authentication method: password me@hosts's password: And the /var/log/auth.log output: Jan 16 09:57:11 host sshd[1957]: reverse mapping checking getaddrinfo for cpe-70-114-155-20.austin.res.rr.com [70.114.155.20] failed - POSSIBLE BREAK-IN ATTEMPT! Jan 16 09:57:13 host sshd[1957]: pam_sm_authenticate: Called Jan 16 09:57:13 host sshd[1957]: pam_sm_authenticate: username = [astacy] Jan 16 09:57:13 host sshd[1959]: Passphrase file wrapped Jan 16 09:57:15 host sshd[1959]: Error attempting to add filename encryption key to user session keyring; rc = [1] Jan 16 09:57:15 host sshd[1957]: Accepted password for astacy from 70.114.155.20 port 42481 ssh2 Jan 16 09:57:15 host sshd[1957]: pam_unix(sshd:session): session opened for user astacy by (uid=0) Jan 16 09:57:20 host sudo: astacy : TTY=pts/0 ; PWD=/home/astacy ; USER=root ; COMMAND=/usr/bin/tail -f /var/log/auth.log The strange thing is that once I've got this first login session, I run the exact same ssh command, and publickey authentication works: [me@my-laptop:~]$ ssh -vv host ... debug1: Server accepts key: pkalg ssh-rsa blen 277 ... [me@host:~]$ And the /var/log/auth.log output is: Jan 16 09:59:11 host sshd[2061]: reverse mapping checking getaddrinfo for cpe-70-114-155-20.austin.res.rr.com [70.114.155.20] failed - POSSIBLE BREAK-IN ATTEMPT! Jan 16 09:59:11 host sshd[2061]: Accepted publickey for astacy from 70.114.155.20 port 39982 ssh2 Jan 16 09:59:11 host sshd[2061]: pam_unix(sshd:session): session opened for user astacy by (uid=0) What do I need to do to make publickey authentication work on the first login? NOTE: When I installed Ubuntu 10.10, I checked the 'encrypt home folder' option. I'm wondering if this has something to do with the log message "Error attempting to add filename encryption key to user session keyring"

    Read the article

  • SMTP error goes directly to Badmail directory after Queue

    - by Sergio López
    This is the error I got in the .BDR Unable to deliver this message because the follow error was encountered: "This message is a delivery status notification that cannot be delivered.". The specific error code was 0xC00402C7. The message sender was <. The message was intended for the following recipients. [email protected] This is the .bad file I got in the badmail error, Can anyone help me ? I´m getting this error from every mail I try to deliver from several php apps and other apps, the relay is only for 2 ip adresses 127.0.0.1 and the server ip, I telnet the smtp and it seems to work fine the mail go to the queue folder... Im stucked From: postmaster@ALRSERVER02 To: [email protected] Date: Mon, 22 Aug 2011 18:39:38 -0500 MIME-Version: 1.0 Content-Type: multipart/report; report-type=delivery-status; boundary="9B095B5ADSN=_01CC61236DC6DEED00000001ALRSERVER02" X-DSNContext: 7ce717b1 - 1378 - 00000002 - C00402CF Message-ID: Subject: Delivery Status Notification (Failure) This is a MIME-formatted message. Portions of this message may be unreadable without a MIME-capable mail program. --9B095B5ADSN=_01CC61236DC6DEED00000001ALRSERVER02 Content-Type: text/plain; charset=unicode-1-1-utf-7 This is an automatically generated Delivery Status Notification. Delivery to the following recipients failed. [email protected] --9B095B5ADSN=_01CC61236DC6DEED00000001ALRSERVER02 Content-Type: message/delivery-status Reporting-MTA: dns;ALRSERVER02 Received-From-MTA: dns;ALRSERVER02 Arrival-Date: Mon, 22 Aug 2011 18:39:38 -0500 Final-Recipient: rfc822;[email protected] Action: failed Status: 5.3.5 --9B095B5ADSN=_01CC61236DC6DEED00000001ALRSERVER02 Content-Type: message/rfc822 Received: from ALRSERVER02 ([74.3.161.94]) by ALRSERVER02 with Microsoft SMTPSVC(7.0.6002.18264); Mon, 22 Aug 2011 18:39:38 -0500 Subject: =?utf-8?Q?[MantisBT]_Reinicializaci=C3=B3n_de_Contrase=C3=B1a?= To: [email protected] X-PHP-Originating-Script: 0:class.phpmailer.php Date: Mon, 22 Aug 2011 17:39:38 -0600 Return-Path: [email protected] From: Alr Tracker Message-ID: X-Priority: 3 X-Mailer: PHPMailer 5.1 (phpmailer.sourceforge.net) MIME-Version: 1.0 Content-Transfer-Encoding: 8bit Content-Type: text/plain; charset="utf-8" X-OriginalArrivalTime: 22 Aug 2011 23:39:38.0020 (UTC) FILETIME=[C182E640:01CC6124] Si solicitó este cambio, visite la siguiente URL para cambiar su contraseña: Usuario: slopez Dirección IP remota: 189.191.159.86 NO RESPONDA A ESTE MENSAJE --9B095B5ADSN=_01CC61236DC6DEED00000001ALRSERVER02--

    Read the article

  • Restore passwd for root on a server

    - by s.mihai
    Hello,       I have a DVR server with linux embeded. It has some telnet functions but i don't have the password for it (the chinese manufacturer refuses to give me the password). I did get a upgrade folder from them and found a passwd file inside.       So i assume that when i upgrade the firmware the password in that file will be used.       Now i am trying to modify the file so taht i can insert a password i already know.       The problem is that i don't know how to create the password hash from what i figured the password hash is $1$1/lfbDKX$Hmd.FqzB8IZEohPesYi961       The file is named rom.ko and i found a command telnetd /mnt/yaffs/web/boa -c /mnt/yaffs/web & /bin/cp -f /mnt/yaffs/rom.ko /etc/shadow in a script file so i assume this is the right way.       Can you help me reconstruct a password that i know already? Tell me how or make one for me :) ?... passwd file: root:$1$1/lfbDKX$Hmd.FqzB8IZEohPesYi961:0:0:99999:7:-1:-1:33637592 bin::10897:0:99999:7::: daemon::10897:0:99999:7::: adm::10897:0:99999:7::: lp::10897:0:99999:7::: sync::10897:0:99999:7::: shutdown::10897:0:99999:7::: halt::10897:0:99999:7::: mail::10897:0:99999:7::: news::10897:0:99999:7::: uucp::10897:0:99999:7::: operator::10897:0:99999:7::: games::10897:0:99999:7::: gopher::10897:0:99999:7::: ftp::10897:0:99999:7::: nobody::10897:0:99999:7::: next::11702:0:99999:7:::

    Read the article

  • Bridged virtual interface is not available or visible to ifconfig.

    - by Omniwombat
    Hello all. I'm running Ubuntu 9.04, kernel 2.6.28-18, and vmware-server 2.0.1. I'm attempting to setup a virtual linux machine to use a bridged interface rather than NAT or host-only. Both NAT and host-only work just fine. When running vmware-config.pl, I set /dev/vmnet0 to bridge eth0, /dev/vmnet1 to host-only, and /dev/vmnet8 to NAT. When I run ifconfig -a I see the physical interface (eth0), vmnet1 and vmnet8 both of which are up and have IP addresses assigned to them. I also see other various interfaces that are not relevant here. In the web console, when I ask that the guest machine's network card be bridged, it states that a bridged setup is "Not available" and shows the disabled device icon. Inside the guest machine, I do have an eth0 interface which I can set to anything I like, however it can't see my external network, or the host. I do see errors in my vmware/hostd.log which state: "The network bridge on device vmnet0 is not running. The virtual machine will not be able to communicate with the host or with other machines on your network" which confirms the problem. vmnet-bridge is running, and I see the following in my process table: /usr/bin/vmnet-bridge -d /var/run/vmnet-bridge-0.pid -n 0 -i eth0 I confirm that the /var/run/vmnet-bridge-0.pid file is there and that it points to the correct process. I saw this question relating to Ubuntu 9.04 and bridged interfaces, in which the poster determined that the vsock library was not getting built due to a flaw in the vmware-config.pl script. I applied the patch, reran the script, and confirm that vsock.ko and vsock.o are in my /lib directory structure. vsock does show up in an lsmod. My /etc/vmware directory has /vmnet1 and /vmnet8 subdirectories. They contain configuration utilities for running DHCP and nat type services as expected. There is no vmnet0 subdirectory. My /etc/vmware/netmap.conf file DOES show entries for vmnet0; both the name and the device as I configured it from the script. My /dev directory contains devices vmnet0 through vmnet9. They have major device number 119, and minor device numbers 0 through 9. /proc/net/dev shows statistics for vmnet1 and vmnet8, but not vmnet0. I have a /proc/vmnet directory, but it's empty. When I start or stop the vmware service with /etc/init.d/vmware start, I see the following: Starting VMware services: Virtual machine monitor done Virtual machine communication interface done VM communication interface socket family: done Virtual ethernet done Bridged networking on /dev/vmnet0 done Host-only networking on /dev/vmnet1 (background) done DHCP server on /dev/vmnet1 done Host-only networking on /dev/vmnet8 (background) done DHCP server on /dev/vmnet8 done NAT service on /dev/vmnet8 done VMware Server Authentication Daemon (background) done Shared Memory Available done Starting VMware management services: VMware Server Host Agent (background) done VMware Virtual Infrastructure Web Access Starting VMware autostart virtual machines: Virtual machines done Nothing appears to be wrong there. What n00b thing am I doing such that vmnet0 and only vmnet0 does not show up in the interface list?

    Read the article

  • KVM + Cloudmin + IpTables

    - by Alex
    I have a KVM virtualization on a machine. I use Ubuntu Server + Cloudmin (in order to manage virtual machine instances). On a host system I have four network interfaces: ebadmin@saturn:/var/log$ ifconfig br0 Link encap:Ethernet HWaddr 10:78:d2:ec:16:38 inet addr:192.168.0.253 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::1278:d2ff:feec:1638/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:589337 errors:0 dropped:0 overruns:0 frame:0 TX packets:334357 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:753652448 (753.6 MB) TX bytes:43385198 (43.3 MB) br1 Link encap:Ethernet HWaddr 6e:a4:06:39:26:60 inet addr:192.168.10.1 Bcast:192.168.10.255 Mask:255.255.255.0 inet6 addr: fe80::6ca4:6ff:fe39:2660/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:16995 errors:0 dropped:0 overruns:0 frame:0 TX packets:13309 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:2059264 (2.0 MB) TX bytes:1763980 (1.7 MB) eth0 Link encap:Ethernet HWaddr 10:78:d2:ec:16:38 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:610558 errors:0 dropped:0 overruns:0 frame:0 TX packets:332382 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:769477564 (769.4 MB) TX bytes:44360402 (44.3 MB) Interrupt:20 Memory:fe400000-fe420000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:239632 errors:0 dropped:0 overruns:0 frame:0 TX packets:239632 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:50738052 (50.7 MB) TX bytes:50738052 (50.7 MB) tap0 Link encap:Ethernet HWaddr 6e:a4:06:39:26:60 inet6 addr: fe80::6ca4:6ff:fe39:2660/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:17821 errors:0 dropped:0 overruns:0 frame:0 TX packets:13703 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:500 RX bytes:2370468 (2.3 MB) TX bytes:1782356 (1.7 MB) br0 is connected to a real network, br1 is used to create a private network shared between guest systems. Now I need to configure iptables for network access. First of all I allow ssh sessions on port 8022 on the host system, then I allow all connections in state RELATED, ESTABLISHED. This is working ok. I install another system as guest, it's IP address is 192.168.10.2, and now I have two problems: I want to allow the access from this host to the outside world, cannot accomplish this. I can ssh from the host. I want to be able to ssh to the guest from the outside world using 8023 port. Cannot accomplish this. Full iptables configuration is following: ebadmin@saturn:/var/log$ sudo iptables --list [sudo] password for ebadmin: Chain INPUT (policy DROP) target prot opt source destination ACCEPT all -- anywhere anywhere ACCEPT tcp -- anywhere anywhere tcp dpt:8022 ACCEPT all -- anywhere anywhere state RELATED,ESTABLISHED LOG all -- anywhere anywhere LOG level warning Chain FORWARD (policy ACCEPT) target prot opt source destination LOG all -- anywhere anywhere LOG level warning Chain OUTPUT (policy ACCEPT) target prot opt source destination LOG all -- anywhere anywhere LOG level warning ebadmin@saturn:/var/log$ sudo iptables -t nat --list Chain PREROUTING (policy ACCEPT) target prot opt source destination DNAT tcp -- anywhere anywhere tcp spt:8023 to:192.168.10.2:22 Chain INPUT (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination Chain POSTROUTING (policy ACCEPT) target prot opt source destination The worst of all is that I don't know how to interpret iptables logs. I don't see the final decision of the firewall. Need help urgently.

    Read the article

  • How to set up the jdbc driver to connect to hsqldb from libreoffice?

    - by rumtscho
    I am trying to "split" a LibreOffice .odb file into a HSQL database and an OpenOffice document containing forms and macros. I am trying to follow the instructions from this thread: Within a few minutes you can convert your embedded HSQLDB to a stand-alone HSQLDB which is just a very fine database engine. 1) Download and extract the current version from http://hsqldb.org/ and point the Java class path in ToolsOptionsJava to the new hsqldb.jar 2) Extract the database folder from your embedded database and rename the files data, properties, script to name.data name.properties, name.script where "name." is an arbitrary name prefix. 3) Connect a Base document to an existing JDBC database such as jdbc:hsqldb:file:/home/chenier/hsqldb/name;default_schema=true;shutdown=true;hsqldb.default_table_type=cached;get_column_name=false (again, "name" refers to your own file name prefix). This local single-user connection gives you much more than the embedded HSQLDB. 4) Copy queries, forms and reports from the old database over to the new one. The wizard presents me with a window expecting two inputs: a "Datasource URL" and a "JDBC driver class". As far as I can tell, the tutorial above only tells me what to put into the Datasource URL. As for the JDBC driver class, I have no idea what to write into this field. I tried the fully-qualified name of the Java class, org.hsqldb.jdbc.JDBCDriver as given in the HSQLDB documentation. When that failed, I tried the physical path /var/lib/hsqldb/lib/hsqldb.jar (although that should have been unnecessary, because first I pointed to this path as described under 1 and then restarted LibreOffice). In both cases, "Test class" failed with the message "The JDBC driver could not be loaded". OpenOffice's documentation doesn't say anything sensible about the field, it was something like "enter the JDBC driver in this box". Any ideas what I should enter there to get the connection working?

    Read the article

  • Help me understand Ubuntu user/group permissions.

    - by Bartek
    I'm beginning to deal with more than one user on my system (it's a VPS serving some sites) and I need to make sure I understand how group permissions work. Here's my setup: I have an account named "admin" .. it's basically the primary account that is used for serving most of the sites that I control myself. Now, I added a second account named "Ville" as one of my users wants to be able to administer that site. So, I can do this the easy way and just chown their domains folder under the ville user and viola, they have permission to do whatever they need be and so forth. However, let's say I want to also give the admin user access to the files (modifying and all) .. how can I put both users into the same group and give them both permission? I've tried doing: sudo usermod -a -G admin ville To add the ville into the admin group, but ville still cannot edit files by admin. Permissions for the primary directory for the ville user are read/write for both owner and group, and the current group for the files is admin:admin .. But ville still can't write into the directory. So, what should I be doing here to get this right and secure at the same time? Thank you.

    Read the article

  • openvpn not creating internal route for client

    - by user42055
    I have two openvpn clients and a server using shared keys. I have internal routes specified in the ccd directory for both clients, but when they connect, the server only creates the internal route for one of them, despite the logs saying it's creating both. Both clients and the server use the "--script-security 2" command-line option. Can anyone think of why it would do this ? My ccd files are: client1: iroute 192.168.0.0 255.255.255.0 client2: iroute 10.0.1.0 255.255.255.0 My log file shows the following (cropped): May 3 17:22:59 kino openvpn[2416]: 118.208.58.60:48730 [client1] Peer Connection Initiated with 118.208.58.60:48730 May 3 17:22:59 kino openvpn[2416]: client1/118.208.58.60:48730 OPTIONS IMPORT: reading client specific options from: ccd/client1 May 3 17:22:59 kino openvpn[2416]: client1/118.208.58.60:48730 MULTI: Learn: 192.168.150.10 -> client1/118.208.58.60:48730 May 3 17:22:59 kino openvpn[2416]: client1/118.208.58.60:48730 MULTI: primary virtual IP for client1/118.208.58.60:48730: 192.168.150.10 May 3 17:22:59 kino openvpn[2416]: client1/118.208.58.60:48730 MULTI: internal route 192.168.0.0/24 -> client1/118.208.58.60:48730 May 3 17:22:59 kino openvpn[2416]: client1/118.208.58.60:48730 MULTI: Learn: 192.168.0.0/24 -> client1/118.208.58.60:48730 May 3 17:23:01 kino openvpn[2416]: client1/118.208.58.60:48730 PUSH: Received control message: 'PUSH_REQUEST' May 3 17:23:01 kino openvpn[2416]: client1/118.208.58.60:48730 SENT CONTROL [client1]: 'PUSH_REPLY,route 192.168.150.1,topology net30,ping 10,ping-restart 120,ifconfig 192.168.150.10 192.168.150.9' (status=1) May 3 17:21:36 kino openvpn[2416]: 124.148.1.90:59277 [client2] Peer Connection Initiated with 124.148.1.90:59277 May 3 17:21:36 kino openvpn[2416]: client2/124.148.1.90:59277 OPTIONS IMPORT: reading client specific options from: ccd/client2 May 3 17:21:36 kino openvpn[2416]: client2/124.148.1.90:59277 MULTI: Learn: 192.168.150.14 -> client2/124.148.1.90:59277 May 3 17:21:36 kino openvpn[2416]: client2/124.148.1.90:59277 MULTI: primary virtual IP for client2/124.148.1.90:59277: 192.168.150.14 May 3 17:21:36 kino openvpn[2416]: client2/124.148.1.90:59277 MULTI: internal route 10.0.1.0/24 -> client2/124.148.1.90:59277 May 3 17:21:36 kino openvpn[2416]: client2/124.148.1.90:59277 MULTI: Learn: 10.0.1.0/24 -> client2/124.148.1.90:59277 May 3 17:21:39 kino openvpn[2416]: client2/124.148.1.90:59277 PUSH: Received control message: 'PUSH_REQUEST' May 3 17:21:39 kino openvpn[2416]: client2/124.148.1.90:59277 SENT CONTROL [client2]: 'PUSH_REPLY,route 192.168.150.1,topology net30,ping 10,ping-restart 120,ifconfig 192.168.150.14 192.168.150.13' (status=1) And after both clients have connected, the routing table looks like this: 192.168.150.2 0.0.0.0 255.255.255.255 UH 0 0 0 tun0 203.209.167.192 0.0.0.0 255.255.255.224 U 0 0 0 eth0 192.168.150.0 192.168.150.2 255.255.255.0 UG 0 0 0 tun0 192.168.0.0 192.168.150.2 255.255.255.0 UG 0 0 0 tun0 127.0.0.0 0.0.0.0 255.0.0.0 U 0 0 0 lo 0.0.0.0 203.209.167.193 0.0.0.0 UG 0 0 0 eth0 As you can see, it's created the route to 192.168.0.0/24 (client1) but not to 10.0.1.0/24 (client2), even though the log says it's been created. Any suggestions why ?

    Read the article

  • Need advice on a monitoring, reminder and warning application.

    - by cbmeeks
    I am a developer that also has to monitor several things on different servers. Such as: 1) Did all of the MS SQL databases backup last night? 2) Did all of the MySQL databases backup last night? 3) Were the database dumps actually copied to the right folder? 4) How much free space is left on each server's hard drives? 5) How big are folders "abc", "def", "etc" getting? 6) Send emails/alerts when thresholds are reached Etc. Just basically something to help me NOT forget such important things. I thought about writing something myself but didn't want to waste the effort if something is already out there. I would also prefer one application instead of many if I could. Thanks. EDIT Forgot to mention the operating system. These run on Windows Server 2003 and/or 2008. In fact, what would be cool is a program that supports multiple servers from one machine. Something that can log into those servers.

    Read the article

  • How to run a website domain without redirecting if IP is already used for another website? [duplicate]

    - by SSpoke
    This question already has an answer here: Hosting multiple distinct folders for distinct domains 1 answer I bought a VPS Host that gave me only 1 IP Address which I used on my first domain name and it works without any problems. Now my second domain name I can't use the same ip address as it points to the first domain name. So I figured my only option was to use a GoDaddy hosted iframe redirection which redirects to a sub folder on my first domain which worked so far. Now I'm trying to load paypal from <?php headers() ?> and I get a permission error because of that iframe Refused to display 'https://www.paypal.com/cgi-bin/webscr?notify_url=&cmd=_cart&upload=1&business=removed&address_override=1' in a frame because it set 'X-Frame-Options' to 'SAMEORIGIN'. How do I avoid the Iframe solution for my second domain while not messing up my first domain? Somebody I forgot once told me it doesn't matter if you have 1 IP Address you could host multiple websites on it? how it that possible the DNS doesn't seem to work off ports afaik, yes I could host multiple websites on different folders but that's not what I call hosting a real website it has to be pointed by a domain name, so this iframe issue doesn't happen My server configuration is httpd (apache) that comes with CentOS 6 (Linux) operating system

    Read the article

< Previous Page | 667 668 669 670 671 672 673 674 675 676 677 678  | Next Page >