Search Results

Search found 40998 results on 1640 pages for 'setup project'.

Page 673/1640 | < Previous Page | 669 670 671 672 673 674 675 676 677 678 679 680  | Next Page >

  • Multi-site email relay based on email address (in AD?)

    - by MarkRobinson
    We have a multi site setup currently based around Exchange 2003, but we are getting a lot of traffic over the vpn as only one server has an internet facing IP. Is there such a product that could sit on a hosted rack somewhere that would look at an incoming email and from information in AD determine which mail server to relay the message to?

    Read the article

  • What is the best way to remove duplicate files on web hosting's FTP server?

    - by Eric Harrison
    For some reason(Happened before I started working on this project)- my client's website has 2 duplicates of every single file. Effectively tripling the size of the site. The files look much like this: wp-comments-post.php | 3,982 bytes wp-comments-post (john smith's conflicted copy 2012-01-12).php | 3,982 bytes wp-comments-post (JohnSmith's conflicted copy 2012-01-14).php | 3,982 bytes The hosting that the website is on has no access to bash or SSH. In your opinion, what would be the easiest way to delete these duplicate files that would take the least time?

    Read the article

  • Image backup with two Macs

    - by Konzepz
    Hi, My setup is as follows: iMac + Ext. HD in the living room A MacBook I want to create a regular weekly backup flow, that will create an image file for the MacBook (the entire disk image), and save it to the ext. HD on the iMac, meaning -- connect via local network and save the file. What's the best practice/application for this? Thank you.

    Read the article

  • How can order of IP addresses issued be controlled?

    - by warren
    Every home router I've setup/used issues addresses from low to high. However, dhcpd from the Internet Systems Consortium seems to issue addresses in reverse order - ie, high to low. Is there a way to change this so that addresses are issued starting at the bottom of the range, and progress higher?

    Read the article

  • APPCMD syntax issue

    - by Adam
    I am trying to setup recycling logging events, using the following: appcmd set config /section:applicationPools /[name=' AppPoolName '].recycling.logEventOnRecycle:time But I am getting this error: Failed to process input: The parameter ''].recycling.logEventOnRecycle:time' mus t begin with a / or - (HRESULT=80070057). I used this technet article but I cannot figure out where I went wrong. Any ideas?

    Read the article

  • Hybrid gmail MX + postfix for local accounts

    - by krunk
    Here's the setup: We have a domain, mydomain.com. Everything is on our own server, except general email accounts which are through gmail. Currently gmail is set as the MX record. The server also has various email aliases it needs to support for bug trackers and such. e.g. [email protected] |/path/to/issuetracker.script I'm struggling with a setup that allows the following, both locally and from user's email clients. guser1 - has a gmail account and a local account guser2 - only has a gmail account bugs - has a pipe alias in /etc/aliases for issue tracker Scenarios mail to [email protected] from local host (crons and such) needs to go to gmail account mail to [email protected] from local host mail to [email protected] needs to be piped to the local issue tracker script So, the first stab was creating a transport map. In this scenario, the our server would be set as teh MX and guser* destined emails are sent to gmail. Put the gmail users in a map like so: [email protected] smtp:gmailsmtp:25 [email protected] smtp:gmailsmtp:25 Problems: Ignores extensions such as [email protected] Only works if append_at_myorigin = no (if set to yes, gmail refuses to connect with: E4C7E3E09BA3: to=, relay=none, delay=0.05, delays=0.02/0.01/0.02/0, dsn=4.4.1, status=deferred (connect to gmail-smtp-in.l.google.com[209.85.222.57]:25: Connection refused)) since append_at_myorigin is set to no, all received emails have (unknown sender) The second stab was to set explicit localhost aliases in /etc/aliases and do a domain wide forward on mydomain. This too requires setting the local server as the MX: root: root@localhost # transport mydomain.com smtp:gmailsmtp:25 Problems: * If I create a transport map for a domain that matches "$myhostname", the aliases file is never parsed. So when a local user (or daemon) sends an email like: mail -s "testing" root < text.txt Postfix ignores the /etc/alias entry and maps to [email protected] and attempts to send it to the gmail transport mapping. Third stab: Create a subdomain for the bugs, something like bugs.mydomain.com. Set the MX for this domain to local server and leave the MX for mydomain.com to the Gmail server. Problems: * Does not solve the issue with local accounts. So when the bug tracker responds to an email from [email protected], it uses a local transport and the user never receives the email. % postconf -n alias_database = hash:/etc/aliases alias_maps = hash:/etc/aliases append_at_myorigin = no append_dot_mydomain = no biff = no config_directory = /etc/postfix inet_interfaces = all mailbox_command = procmail -a "$EXTENSION" mailbox_size_limit = 0 mydestination = $myhostname, localhost.$myhostname, localhost myhostname = mydomain.com mynetworks = 127.0.0.0/8 [::ffff:127.0.0.0]/104 [::1]/128 myorigin = /etc/mailname readme_directory = no recipient_delimiter = + relayhost = smtp_tls_cert_file = /etc/ssl/certs/kspace.pem smtp_tls_enforce_peername = no smtp_tls_key_file = /etc/ssl/certs/kspace.pem smtp_tls_note_starttls_offer = yes smtp_tls_scert_verifydepth = 5 smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache smtp_use_tls = yes smtpd_banner = $myhostname ESMTP $mail_name (Debian/GNU) smtpd_recipient_restrictions = permit_mynetworks, reject_invalid_hostname, reject_non_fqdn_sender, reject_non_fqdn_recipient, reject_unknown_sender_domain, reject_unknown_recipient_domain, reject_unauth_destination smtpd_tls_ask_ccert = yes smtpd_tls_req_ccert = no smtpd_tls_session_cache_database = btree:${data_directory}/smtpd_scache tls_random_source = dev:/dev/urandom transport_maps = hash:/etc/postfix/transport

    Read the article

  • Ubuntu Desktop system restore ?

    - by neolix
    Hello Geeks, We are using all the desktop ubuntu 8.04 to 10.04, we are looking same thing like system resorting to back date like windows feature. Around 500 desktop and 79 server we want to setup. Thanks

    Read the article

  • Cannot send emails from outlook 2010 for an exchange account

    - by Mahmoud Saleh
    i have setup an exchange 2010 account on microsoft outlook 2010 and i can read my emails, but i am not able to send emails, when i create a new email and click send, the messages are not sent, they don't even get to the outbox folder. my guess is that the issue is not from exchange itself, becuase i can send emails with this exchange account with java code using smtp port 25 please advise how to fix this issue.

    Read the article

  • HTML notes in freemind

    - by asdf
    Hi, I wonder if the following things can be done with the HTML notes pane of freemind: Is it possible on the layout view to decrease the separation between lines? The panel is horizontal, is it possible to setup a vertical view? (I have a big, horizontal-like monitor) By the way, when I move the mouse pointer over a node, i can see the HTLM note associated with it, but its view (as a yellow square) only lasts for some seconds. Can it be made permament? Thanks a lot

    Read the article

  • Complete stack traces from Hyperic

    - by Mike Kushner
    I've setup Hyperic to run on our CI-machine, and every once in a while it reacts to some random stack trace and sends of an alert. So far so good, we've caught a lot of intermittent bugs that way. My only issue is that the alert only contains the first error line and not the entire stack trace, which requires me to access the machine and look at the logs manually. Is there any way to modify the alert message to contain more information, alternatively to include the log file in the alert mail?

    Read the article

  • SafeOffice 500 - how to enable VPN access to another network (out)

    - by Dani
    Hi, I have a safe office 500 box at my edge. (checkpoint's hardware firewall) I'm trying to connect to another office VPN using windows 7 pptp connection. It fails (saying something about enabling GRE). (after authenticating, hangs for a while, than give the error message.) Using the same computer with direct internet access (not behind the firewalls) works fine and I get connected. how do I setup the safe office to enable me to use vpn (pptp) out connections.

    Read the article

  • How can I make monodevelop render text in KDE?

    - by Spikolynn
    Monodevelop from git in KDE 4.10.2 does not render text in code edit tabs I tried with xfce and text is rendered ok there. I tried disabling composition with alt shift f12 and restarting x server but it was no better. I also tried disabling font softening in monodevelop options and disabling plugins. I also tried temporarily deleting my KDE profile. This is dual screen setup on Nvidia with nouveau. OS is slackware64-current.

    Read the article

  • Operative systems on SD cards

    - by HisDudeness
    I was getting some wild ideas the last days, like putting some operative systems into SD cards rather than on my hard drive. I'll go further into details now and explain what lead me to consider this probably abominable decision. I am on a laptop (that means I have a native SD-card reader) which is currently running a cross-distro setup, with a bunch of Linux systems (placed in dedicated ext4 logical partitions into a huge extended one) regulated by an unique GRUB. Since today, my laptop haven't even seen any Windows system with binoculars. I was thinking about placing all the os part of my setup into a Secure Digital to save all my 500 Gb Hard Drive for documents, music, videos and so on, and being able to just remove the SD and boot my system into another computer too, as well as having the possibility of booting other systems into mine by just plugging in another SD, without having to keep it constantly placed in my PC. Also, in the remote case in the near future I just wanted to boot Windows 8 in it, I read it causes major boot incompatibility issues with other systems by needing a digital signature in order for them to start. By having it in a removable drive, I could just get rid of it when I'm needing him and switch its card with Linux one, and so not having any obstacles to their boot. Now, my questions are: I know unlikely traditional rotating disk drives, integrated circuits ones have a limited lifespan in terms of cluster rewriting. Is it an obstacle to that kind of usage? I mean, some Ultrabooks are using SSD now, is it the same issue, or there are some differences between Solid State Drives and Secure Digitals in that sense? Maybe having them to store system files which are in fixed positions (making the even-usage of cluster technology useless) constantly being re-read and updated and similar things just gets them soon unserviceable, do it? Second question: are all motherboards and BIOSes able to boot from SDs just like they are from USB pen drives (I mean, provided card reader is USB-connected, isn't it)? Or can't bootloaders like GRUB be installed on SDs working? If they can't, is it a solution installing GRUB to MBR and making boot option pointing to SD? Will it work? Are there any other problems to installing OSs on a Secure Digital?

    Read the article

  • Celery and Django : How to start at boot in production env (linux)

    - by llazzaro
    Hello, I have and app that uses celery and django to run distribuited tasks (like send email, crawl web,etc). The app never wa sin prod, so I always start celeryd with ./manage celeryd. I want to setup a pre-post env in linux, and I will need information in how to make an init.d script for start the celeryd for django. (I had made some init.d scripts before, no need complete script just relevant part) Thanks!

    Read the article

  • Cannot install grub to RAID1 (md0)

    - by Andrew Answer
    I have a RAID1 array on my Ubuntu 12.04 LTS and my /sda HDD has been replaced several days ago. I use this commands to replace: # go to superuser sudo bash # see RAID state mdadm -Q -D /dev/md0 # State should be "clean, degraded" # remove broken disk from RAID mdadm /dev/md0 --fail /dev/sda1 mdadm /dev/md0 --remove /dev/sda1 # see partitions fdisk -l # shutdown computer shutdown now # physically replace old disk by new # start system again # see partitions fdisk -l # copy partitions from sdb to sda sfdisk -d /dev/sdb | sfdisk /dev/sda # recreate id for sda sfdisk --change-id /dev/sda 1 fd # add sda1 to RAID mdadm /dev/md0 --add /dev/sda1 # see RAID state mdadm -Q -D /dev/md0 # State should be "clean, degraded, recovering" # to see status you can use cat /proc/mdstat This is the my mdadm output after sync: /dev/md0: Version : 0.90 Creation Time : Wed Feb 17 16:18:25 2010 Raid Level : raid1 Array Size : 470455360 (448.66 GiB 481.75 GB) Used Dev Size : 470455360 (448.66 GiB 481.75 GB) Raid Devices : 2 Total Devices : 2 Preferred Minor : 0 Persistence : Superblock is persistent Update Time : Thu Nov 1 15:19:31 2012 State : clean Active Devices : 2 Working Devices : 2 Failed Devices : 0 Spare Devices : 0 UUID : 92e6ff4e:ed3ab4bf:fee5eb6c:d9b9cb11 Events : 0.11049560 Number Major Minor RaidDevice State 0 8 1 0 active sync /dev/sda1 1 8 17 1 active sync /dev/sdb1 After bebuilding completion "fdisk -l" says what I have not valid partition table /dev/md0. This is my fdisk -l output: Disk /dev/sda: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders, total 976773168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00057d19 Device Boot Start End Blocks Id System /dev/sda1 * 63 940910984 470455461 fd Linux raid autodetect /dev/sda2 940910985 976768064 17928540 5 Extended /dev/sda5 940911048 976768064 17928508+ 82 Linux swap / Solaris Disk /dev/sdb: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders, total 976773168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000667ca Device Boot Start End Blocks Id System /dev/sdb1 * 63 940910984 470455461 fd Linux raid autodetect /dev/sdb2 940910985 976768064 17928540 5 Extended /dev/sdb5 940911048 976768064 17928508+ 82 Linux swap / Solaris Disk /dev/md0: 481.7 GB, 481746288640 bytes 2 heads, 4 sectors/track, 117613840 cylinders, total 940910720 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/md0 doesn't contain a valid partition table This is my grub install output: root@answe:~# grub-install /dev/sda /usr/sbin/grub-setup: warn: Attempting to install GRUB to a disk with multiple partition labels or both partition label and filesystem. This is not supported yet.. /usr/sbin/grub-setup: error: embedding is not possible, but this is required for cross-disk install. root@answe:~# grub-install /dev/sdb Installation finished. No error reported. So 1) "update-grub" find only /sda and /sdb Linux, not /md0 2) "dpkg-reconfigure grub-pc" says "GRUB failed to install the following devices /dev/md0" I cannot load my system except from /sdb1 and /sda1, but in DEGRADED mode... Anybody can resolve this issue? I have big headache with this.

    Read the article

  • Internet Explorer cannot display page from apache with single SSL virtual host

    - by P.scheit
    I have a question that has come up somehow in different questions but I still can't find the solution, yet. My problem is that I'm hosting a site on apache 2.4 on debian with SSL and Internet Explorer 7 on windows xp shows Internet Explorer cannot display the webpage I have only ONE virtual host that uses ssl, but DIFFERENT virtual hosts that use http. Here is my config for the site with SSL enabled (etc/sites-avaible/default-ssl is NOT linked) <Virtualhost xx.yyy.86.193:443> ServerName www.my-certified-domain.de ServerAlias my-certified-domain.de DocumentRoot "/var/local/www/my-certified-domain.de/current/www" Alias /files "/var/local/www/my-certified-domain.de/current/files" CustomLog /var/log/apache2/access.my-certified-domain.de.log combined <Directory "/var/local/www/my-certified-domain.de/current/www"> AllowOverride All </Directory> SSLEngine on SSLCertificateFile /etc/ssl/certs/www.my-certified-domain.de.crt SSLCertificateKeyFile /etc/ssl/private/www.my-certified-domain.de.key SSLCipherSuite HIGH:MEDIUM:!aNULL:+SHA1:+MD5:+HIGH:+MEDIUM SSLCertificateChainFile /etc/apache2/ssl.crt/www.my-certified-domain.de.ca BrowserMatch "MSIE [2-8]" nokeepalive downgrade-1.0 force-response-1.0 </VirtualHost> <VirtualHost *:80> ServerName www.my-certified-domain.de ServerAlias my-certified-domain.de CustomLog /var/log/apache2/access.my-certified-domain.de.log combined Redirect permanent / https://www.my-certified-domain.de/ </VirtualHost> my ports.conf looks like this: NameVirtualHost *:80 Listen 80 <IfModule mod_ssl.c> # If you add NameVirtualHost *:443 here, you will also have to change # the VirtualHost statement in /etc/apache2/sites-available/default-ssl # to <VirtualHost *:443> # Server Name Indication for SSL named virtual hosts is currently not # supported by MSIE on Windows XP. Listen 443 </IfModule> <IfModule mod_gnutls.c> Listen 443 </IfModule> the output from apache2ctl -S is like this: xx.yyy.86.193:443 www.my-certified-domain.de (/etc/apache2/sites-enabled/020-my-certified-domain.de:1) wildcard NameVirtualHosts and _default_ servers: *:80 is a NameVirtualHost default server phpmyadmin.my-certified-domain.de (/etc/apache2/conf.d/phpmyadmin.conf:3) port 80 namevhost phpmyadmin.my-certified-domain.de (/etc/apache2/conf.d/phpmyadmin.conf:3) port 80 namevhost staging.my-certified-domain.de (/etc/apache2/sites-enabled/010-staging.my-certified-domain.de:1) port 80 namevhost testing.my-certified-domain.de (/etc/apache2/sites-enabled/015-testing.my-certified-domain.de:1) port 80 namevhost www.my-certified-domain.de (/etc/apache2/sites-enabled/020-my-certified-domain.de:31) I included the solution for this question: Internet explorer cannot display the page, other browsers can, possibly htaccess / server error And I understand the answer from this question: How to setup Apache NameVirtualHost on SSL? In fakt: I only have one ssl certificate for the domain. And I only want to run ONE virtual host with ssl. So I just want to use the one ip for the ssl virtual host. But still (after rebooting / restarting / testing) internet explorer will still not show the page. When I intepret the apachectl -S as well, I already have only one SSL host and this should response to the initial SSH handshake, shouldn't it? What is wrong in this setup? Thank you so much Philipp

    Read the article

  • SMTP Server: '421 unable to verify sender domain'

    - by Tim
    I have recently setup a new SMTP server on my new webserver (win 2008). The server sends mail from a number of domains hosted on the website, everything seems to work OK but I am getting a number of undeliverable reports which state '421 unable to verify sender domain' What does this mean and what should I do about it?

    Read the article

  • Custom hostname instead ISP's

    - by JohnZ
    Hi! I have setup a Centos 5.5 server and a domain name (say mydomain.com) pointing to it (using bind9) with custom nameservers (like ns1.mydomain.com and ns2.mydomain.com). Everything works fine but there is something more I would like to have and don't know if it is possible. Is it possible to have the returned host to be mydomain.com (PHP gethostbyaddr()), not host-static-x-y-a-b.myisp-provider.com? And how do I implement it if it's possible?

    Read the article

  • Internet Speed for Webserver

    - by René
    That should be kind of dumb question in comparison to all other questions here. What minimum upload and download is required for a small home webserver with one webpage? Or is there a schema that shows me the required upload and download speed for a number of visitors? We talk about a Windows Server, but not really sure this is relevant. That's just for a practice project.

    Read the article

  • BSOD when using Visual Studio 2008

    - by I'm raaaaageeed
    Man, I am so fucking mad right now that my hand is broken from punching my piece of shit laptop. Fucking I'm in Visual Studio trying to get work done, and the piece of shit keeps telling me "LOL VSHost.exe crashed!" So I'm like fuck you you little piece of shit and keep ignoring it Then now everytime I start VS2008 and start working on a project I get the following blue screen: STOP: 0x0000007E (0xC000001D, 0x80573002*, 0xF78E6840, 0xF78E653C) = *can barely read my own handwriting on that one sorry lool Btw VSHost.exe was crashing in the mscorwks.dll FUCKING HELP ME I HAVE SO MUCH WORK TO DO

    Read the article

  • Can't login as root but I can SU while logged with another user

    - by Rhyuk
    What I was doing before this happened?: I was tinkering trying to setup X server so I can open an app's GUI remotely so I installed "X Window System", "xclock" and uncommented "# ForwardX11 yes" from my "/etc/ssh/ssh_config". (never got it working but thats a whole other question) Since that moment I'm not able to login as root from Putty (I get Access Denied). I can login as another user and I can "su" successfully so I know the password is right. How can have direct access with root again?

    Read the article

  • Photoshop - How to create master/detail pages?

    - by worchyld
    I am skinning up a website and other things in Photoshop but I am finding the PSD taking a very long time to load/save and I'm wanting to split the PSD file into several files. I've done this, but sometimes I need to adjust one thing and I have to change every PSD file so that the entire project is consistent. Ideally, I'd like to be able to create a master/detail (or a template) structure using Photoshop. What is the best way to achieve this goal? Thanks

    Read the article

  • Setting a Preferred Network Adapter for browsing

    - by ala
    My PC at work is connected to 2 networks; LAN: local corporate network for remote desktop access and very slow internet connection WAN: wireless faster internet browsing Is there a way to setup the default/preferred network adapter for the internet browsing?

    Read the article

  • Any tool to check which ports/protocols firewalls prevent?

    - by Jus12
    Suppose I have a setup as: host_1 --- Firewall_1 --- Internet --- Firewall_2 --- host_2 I need to check which ports are open on host_2 from host_1 (which may be blocked by either firewalls) If there a tool that comes in two parts (one running on host_1 and other on host_2) that does this for me? It should be something like: 1 Listen to all ports on host_2 2 Try to connect to every port on host_2 from host_1 3 Give a report what ports are allowed.

    Read the article

< Previous Page | 669 670 671 672 673 674 675 676 677 678 679 680  | Next Page >