Search Results

Search found 21717 results on 869 pages for 'setup versions'.

Page 679/869 | < Previous Page | 675 676 677 678 679 680 681 682 683 684 685 686  | Next Page >

• Raid-1 Western Digital Green AARS, cloning and WD Align Utility

  - by Jaguar

  Hello all, My current setup runs on top of 2x Western Digital 2500KS drives on Raid-1, using the motherboard's 780G raid controller, on WinXP. Everything is fine, but the drives are a bit noisy. I am considering buying 2x WD6400AARS disks which are the 640GB slower 'green' drives, but also feature the Advanced Formatting 4KB sectors. This means that for WinXP the partition will have to be aligned to work properly, else there is a performance penalty. There are 2 questions here: The Green drives from WD are all slower and are (according to WD) susceptible to drop-out's from the controller. Has anyone any experience in this matter? Is there a possibility the controller will drop a drive? If so, can i do anything about it? Secondly, western digital gives a utility to perform the alignment on the partition. The thing is, will the utility see the drives in question as the operating system only sees 1 logical disk? I will be making the transition using a cloning tool (most probably norton ghost) unless i don't find a solution or a clear answer, in which case i'll just buy a win 7 license and make a clean install... thx in advance

  Read the article

• Macbook Pro 2010 Ethernet Jumbo Frame(9k MTU) Support?

  - by Troggy

  Has anyone been able to use jumbo frame support on their 2010 Macbook Pros? This is kind of negative news here, but I am seeing many reports that this is not available anymore due to Apple's choice of network card in the new machines. I cannot set my MTU speed over 1500 on my new 2010 MBP i7, but my old early 2008 MBP (Core2) has the 9000 MTU setting for use. Everything I have is setup to use jumbo frames and I thought apple kept that feature in their "pro" lineup. It sounds like the Mac Pro still has it. Did they decide to use a chipset that doesn't support it? I am trying to pinpoint some solid chipset numbers and the feature support. Maybe they just need to update the drivers? Is there some more official information about this feature? This might seem minor, but this is really frustrating if apple removed this feature from their pro laptop line. From what I have read so far, it sounds like I am not alone in my frustrations with this. http://discussions.info.apple.com/message.jspa?messageID=12258067 http://discussions.apple.com/thread.jspa?messageID=12130158 Anyone have any experience or further knowledge about this issue ... beyond typing my question into google and giving the top 5 results as answers? :)

  Read the article

• How to deal with DELL support system?

  - by Nishant Kumar

  We have purchased a Dell Optiplex 9010 SSFV for our organization's work. Since the first installation two of the USB keyboard keys were not working properly. I had to press those keys two times simultaneously, on first time keys did not work and for for second time it printed two characters (as it were buffering first character.) Two keys that were not working properly: Hexangrave (Below the ESC key: `) Double Quotes (Left the enter key ") We registered our complaint with DELL and they suggested (with some hard to understand and weird ENGLISH accent) some test and tricks, such as switching to different ports, checking keyboard on different PC, and it worked well with diff. PC(with Windows 7 Home Premium installed). It was clear that it is an OS fault, hence they suggested to re-install OS. Problem began here, we have a project on the run and currently a video editing project setup on our system, so can't re-install system in hurry and also DELL persons were not providing any other solution such as updating keyboard driver, etc. Arguments I am a Software Engg. and don't think it is a feasible solution to re-install entire system for simple problems. This prob is coming since the fresh system installation, so I don't think it will solve the problem. Finally, I had to find solution myself and got it here, now I want to show my disappointment to dell persons or at least tell them that they should improve there support system to not advice to re-install entire system for that simple problems. Notes We have purchased 5 years NEXT business day support from DELL for around 8000 INR (Not for that kind of solutions from DELL). It is Dell India Support System. So can anyone tell me how to tackle dell support system officially, so that they will pay more attention in near future. Thanks

  Read the article

• ESXi 4.0 Guests Locking up

  - by Brendan Sherwin

  I installed ESXi 4.0 on an HP Proliant g5 with a 64bit Xeon processor and took advantage of the free license as I work for a public school. I created two instances of server 2003 from scratch, one to be the DC, DHCP, the other to be a file server and DNS/DHCP backup. I had both guests up and running fine, setup my user accounts, transferred the data, etc etc. Once I joined a client machine to the domain, I would find that both of my Windows guests would lock up. Sometimes it would be for five or so minutes, once it was overnight. The "locked up" state means that as far I could tell, all services were stopped; dhcp no longer handed out IP's, DNS stopped working, I couldn't RDP into the server. The ESXi host, my HP server, was still running fine. VSphere was working, and I could look at the performance of the individual guests.I would try Powering off the hosts from inside VSPhere, and the hosts would start powering off, but get stuck at 95%, and stay that way, sometimes only for 10 minutes, others for hours. Several times I had to restart ESXi from it's console in order to restart my machines. Now, can anyone tell me what is happening, and how I can fix it, or take steps to prevent it? I hired a consultant to come take a look at it, someone who's experience and knowledge I trust, and he told me he had never seen anything like this ever before. He spoke to a friend of his who is VM certified, and he also said he had never heard of this issue. Thanks for your replies, and I'll do my best to respond ASAP. Currently, the server is powered off, and I've reinstituted my nine year old Server 2000 boxes, and I'm considering installing ESXi 3.5. Does anyone know a host created in 4.0 will work in 3.5? I'd really like to avoid having to rebuild those accounts! I know 4.0 works on this server, as I have another server in another school with the same exact hardware running 4.0 fine. Brendan

  Read the article

• Cannot push to GitHub from Amazon EC2 Linux instance

  - by Eli

  Having the worst luck push files to a repo from EC2 to GitHub. I have my ssh key setup and added to Github. Here are the results of ssh -v [email protected] OpenSSH_5.3p1, OpenSSL 1.0.0g-fips 18 Jan 2012 debug1: Reading configuration data /etc/ssh/ssh_config debug1: Applying options for * debug1: Connecting to github.com [207.97.227.239] port 22. debug1: Connection established. debug1: permanently_set_uid: 0/0 debug1: identity file /root/.ssh/identity type -1 debug1: identity file /root/.ssh/id_rsa type 1 debug1: identity file /root/.ssh/id_dsa type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.1p1 Debian-5github2 debug1: match: OpenSSH_5.1p1 Debian-5github2 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.3 debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-ctr hmac-md5 none debug1: kex: client->server aes128-ctr hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug1: Host 'github.com' is known and matches the RSA host key. debug1: Found key in /root/.ssh/known_hosts:1 debug1: ssh_rsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey debug1: Next authentication method: publickey debug1: Trying private key: /root/.ssh/identity debug1: Offering public key: /root/.ssh/id_rsa debug1: Remote: Forced command: gerve eliperelman 81:5f:8a:b2:42:6d:4e:8c:2d:ba:9a:8a:2b:9e:1a:90 debug1: Remote: Port forwarding disabled. debug1: Remote: X11 forwarding disabled. debug1: Remote: Agent forwarding disabled. debug1: Remote: Pty allocation disabled. debug1: Server accepts key: pkalg ssh-rsa blen 277 debug1: Trying private key: /root/.ssh/id_dsa debug1: No more authentication methods to try. Permission denied (publickey).

  Read the article

• Force database read to master if slave data is stale

  - by Jeff Storey

  I previously asked a specific question about this database replication for new user signup to which I got an answer, but I want to ask this in the more general sense. I have a database setup in which I am using a master/slave combination. I am using the slaves for load balancing (the data itself is partitioned/sharded across multiple databases, but each database has X slaves for load balancing). Let's say I write some data to the master. Now I do a subsequent read which hits a slave, but the slave has not yet caught up to the master. Is there a way (which can be done quickly since it will happen frequently) to determine if the data is stale in the slave so I can then route to the master? In my previous question, it was suggested to do simultaneous writes to the cache and the database. This solution seems practical, but there is still a chance that the data may have been removed from the cache but not yet updated in the slave. A possible solution is to ensure the cache is big enough (based on the typical application load) so the data will not be evicted within the time frame it takes to replicate the data. This seems like it may be feasible. Can anyone provide additional insight into this question? Thanks!

  Read the article

• Why is vCenter 5.1u1 exiting hosts from maintenance mode?

  - by Shane Madden

  This vCenter server was just upgraded to 5.1 update 1. I'm going through hosts and bringing firmware up to date, then upgrading them from various versions of 5.0 to 5.1u1. vCenter 5.1u1 seems to have an interesting new behavior: it's removing hosts from maintenance mode when they reconnect after being disconnected -- but very inconsistently, I've seen it maybe 4 or 5 times on ~25-30 host reboots. I've only seen it happen on 5.0 hosts that have not yet been upgraded to 5.1. In the image, I placed the host in maint mode and rebooted it into the HP SPP DVD's automatic update mode. After its usual ~40 minute update process, the host came back online.. and 7 seconds before even logging that the host had reconnected, vCenter had sent the host a task to exit maintenance mode. In my understanding, the only time vCenter should drop a host out of maintenance mode is when vCenter put it into maintenance mode itself (such as a VUM upgrade task). Why would this vCenter be unilaterally exiting a host from user-initiated maintenance mode? Edit, additional info: I ran the firmware upgrades on 5 more hosts, all at the same time. Two of them exited maint mode after reconnecting, three did not. The common factor of those exiting maint mode seems to be how long they were offline; the two that took a few tries to boot to the virtual media are the two that got knocked out of maint mode. esx31 (image above): 45 minutes unresponsive esx19 (exited maint): 87 minutes unresponsive esx24 (stayed in maint): 32 minutes unresponsive esx29 (stayed in maint): 39 minutes unresponsive esx32 (stayed in maint): 30 minutes unresponsive esx34 (exited maint): 70 minutes unresponsive Edit: The disconnect time idea seems to have been a red herring, as it's not happening consistently. Additionally, in the vpxd.log the exit maint mode task initiation seems to always immediately follow this vim.EnvironmentBrowser.queryProvisioningPolicy SOAP call. Here's the lines, slightly trimmed for clarity: 15:27:49.535 [info 'vpxdvpxdVmomi'] [ClientAdapterBase::InvokeOnSoap] Invoke done (esx31, vim.EnvironmentBrowser.queryProvisioningPolicy) 15:27:49.560 [info 'commonvpxLro'] [VpxLRO] -- BEGIN task -- esx31 -- HostSystem.exitMaintenanceMode -- Note that on the nodes that don't get the exit task, the vim.EnvironmentBrowser.queryProvisioningPolicy event still occurs. I'm not seeing any other differences in events before or after this in the reconnect process, aside from the extra events caused by exiting maintenance mode. Given the log's mention of provisioning policies, looking for autodeploy-related maintenance mode issues turns up complaints about similar behavior (though I'm not using autodeploy at all).

  Read the article

• Chroot jail of Nginx and php

  - by sqren

  I'm hosting multiple websites on one VPS, and want to chroot each website, eg. /chroot/website1 /chroot/website2 I'm using makejail, which is a highlevel tool, for creating the jails, and copying the libraries and dependencies. Easy peasy. Each website will need nginx, php and mysql. For php I'm using php5-fpm which actually supports chroot by configuration, however I'm not using this (maybe I should?) My question is which approach of the following three is the better: 1) Every website will have its own seperated instance of nginx, php and mysql. The downside is, that each webserver + php has to listen to a different port. I also need a "master" nginx web server in front of them, reverse proxying to the chrooted servers behind it. Probably most secure, but also most advanced. 2) I don't make any chroot jails manually. I setup one nginx web server, that proxies php requests to php-fpm, on different ports. I can have multiple php-fpm configurations each with is own chroot'ed folder. This is quite managable - however only php will be chrooted. Not the actual webserver. Is this secure enough. Also, I tried this option out, and it seems I will need to use TCP instead of sockets for connecting to MySQL. 3) You tell me ;) I'm quite new to chroot jailing, so please correct me if I'm wrong in my assumptions. I've been reading all the tutorials I could find, however, I find the market for chroot guides very scarce. Any help or inputs much appreciated!

  Read the article

• Why is site serving different SSL certs to different browsers?

  - by TRiG

  The SSL certificate on menswearireland.com and on www.menswearireland.com works fine on Safari, Chrome, SeaMonkey, K-Meleon, QtWeb, Firefox, and Opera. However, Internet Explorer claims that there is an error: The security certificate presented by this website was not issued by a trusted certificate authority. The security certificate presented by this website was issued for a different website's address. Security certificate problems may indicate an attempt to fool you or intercept any data you send to the server. Mozilla/5.0 (compatible; MSIE 9.0; Windows NT 6.0; Trident/5.0) Another site hosted on the same managed server shows no errors: achill-fieldschool.com and www.achill-fieldschool.com work fine on IE, even though as far as I can tell the certificate is set up identically. What am I doing wrong? This is a LAMPP server running Plesk. It looks like the server is showing different certificates to different clients. To some clients it shows a RapidSSL certificate made out to www.menswearireland.com with menswearireland.com as a valid alternative name. To other clients, it shows a Parallels Panel certificate, made out to Parallels Panel. Here are results from a few different online SSL checkers: most say it's fine, while two show errors. Three online checkers say it's valid Comodo SSL Check shows it as valid DigiCert SSL Check shows it as valid SSL Shopper SSL Check shows it as valid Common name: www.menswearireland.com SANs: www.menswearireland.com, menswearireland.com Valid from October 2, 2012 to November 4, 2013 Serial Number: 559425 (0x88941) Signature Algorithm: sha1WithRSAEncryption Issuer: RapidSSL CA Another online checker seems to see a completely different certificate GeoCerts SSL Check shows it as invalid Common name: Parallels Panel Organization: Parallels Valid from August 15, 2012 to August 15, 2013 Issuer: Parallels Panel Another online checker sees more than one certificate Symantic SSL Check shows it as invalid The certificate installation checker connected to the Web server and read its certificates, but could not determine which is the primary certificate for the Web server. Incidentally, on both menswearireland.com and achill-fieldschool.com the homepage will redirect from HTTPS to HTTP. To see SSL details, visit the page /account on both (that page will redirect from HTTP to HTTPS). I’ve found more information in a more detailed online SSL checker. https://www.ssllabs.com/ssltest/analyze.html?d=menswearireland.com This site works only in browsers with SNI support My understanding is that SNI (RFC 6066) is a method for putting many SSL sites on one shared IP address and port. This does not work on Internet Explorer on older versions of Windows (this has to do with the version of Windows, not the version of Internet Explorer). However, all our SSL sites are on a unique IP address, so we shouldn’t need SNI.

  Read the article

• Windows 7 disk backup and clone for deployment to multiple systems

  - by gregmac

  I'm in the process of deploying some new PCs (there's only 8), all identical hardware. What I'd like to do is install Windows 7 (64bit), join to domain etc, install a bunch of other software, and then clone that drive to multiple other machines. I'd also like to be able to use it as a backup image, so the machine can be restored back to that image at some future date. I understand this involves at least sysprep, but I am confused after reading some tutorials that talk about using Windows Automated Installation Kit, or hacks with the registry and custom-build batch files. This process seems overly complex to me: I did something similar 10+ years ago, and and don't remember it being this bad. Surely things have improved in a decade? There's also some products that involve having network servers running deployment software, network boot, etc etc.. this is way more than I want to set up. My systems are all identical hardware. Is there a simplified way to clone PCs? Preferably (since I'm a lazy developer, and not an IT admin) I'd like to find some off-the-shelf product that I can run after I get the machine setup, that will spit out a bootable DVD I can run on all the other systems, which will boot up, ask for a computer name, join it to the domain, and that's it. Does such as product exist?

  Read the article

• Application losing Printer within Terminal Services for remote users

  - by Richard

  Question: What I need to do is have a permanent link to a printer, normally only accessible through Terminal Services (Printer Redirect), to allow Sage Line 50 layouts to see that printer persistently, even after users have disconnected and reconnected to the Terminal Services session? Although the printer is accessible each time a user connects to the Sage Server via Terminal Services, it is given a different session number and therefore the Sage Layout sees it as a different printer. History behind question: Users using Terminal Services connecting to a Sage Server on a different site Using Sage Line 50 v 15 on that Server Users want to print invoices (sage layouts) locally Sage Server cannot see the users local printers, to get around this user uses the Print redirect features of Terminal Services The individual reports can be edited to point to a specific printer by default. This means the user just has to select an invoice and click print, then select the layout/report wanted and it auto prints that invoice to the default printer specified. The problem occurs because the layouts are edited to point to the users local printer "Ricoh 1018d (session#)", note the "(session#)" as this is the users local printer being redirected through the terminal services session. Users are able to print using the sage layouts once the default printer is setup within the layout and saved, but as soon as the users disconnects from the Terminal Services session and then reconnect in the morning go to print, it has lost the connection to that printer. I understand why its failed, because that the printer is on a per session basis and the layout would not be able to hold on to the connection from a previous session. Thanks in advance for any assistance...

  Read the article

• DNS configuration issues. Clients inside network unable to resolve DNS server's name

  - by hydroparadise

  Setup the DNS service on Ubuntu 12.04 64 and all apears to be well except that my dhcp clients do not recognize my DNS servers hostname. When doing a nslookup on one of my Windows clients, I get C:\Users\chad>nslookup Default Server: UnKnown Address: 192.168.1.2 Where I would expect the FQDN in the spot where UnKnown is seen. The DNS server know's itself pretty well, but I think only because I have an entry in the /etc/hosts file to resolve. There's so many places to look I don't even know where to begin. Are there any logs I can look at? Something. Places I've looked at and configured: /etc/bind/zones/domain.com.db /etc/bind/zones/rev.1.168.192.in-addr.arpa /etc/bind/named.conf.local EDIT: '/etc/bind/zones/rev.1.168.192.in-addr.arpa' @ IN SOA dns-serv1.mydomain.com [email protected]. ( 2006081401; 28800; 604800; 604800; 86400 ) IN NS dns-serv1.mydomain.com. 2 IN PTR dns-serv1 2 IN PTR mydomain.com EDIT 2: '/etc/bind/named.conf.local' zone "mydomain.com" { type master; file "/etc/bind/zones/mydomain.com.db"; }; zone "1.168.192.in-addr.arpa" { type master; file "/etc/bind/zones/rev.0.168.192.in-addr.arpa"; };

  Read the article

• external drive enclosure -> software RAID 5?

  - by memilanuk

  Hello all, I have two older PCs on my LAN posing as 'servers'... one running FreeNAS off a USB stick using three 500GB hdds in a ZFS RAID-Z pool serving as storage for the LAN and one running Debian Lenny with an 80GB drive used as a general purpose 'tinker' box that I can ssh into, etc. Problem is that the SMART report for one of those 500GB drives in the FreeNAS box is showing some pre-failure attributes, and the whole array is a little small anyways. Rather than simply replace one 500GB drive with another 500GB drive, and have no backup of the file server, I'd like to upgrade all the drives to 2TB ones - but I have no where to store that much data in the mean while. As such, I started looking at getting a 4-bay external drive enclosure with an eSATA card for the Debian box, with the hopes of creating a RAID5 + LVM setup using those drives and backing the data up to that external drive enclosure. After the backup is done, replace the drives in the FreeNAS box and rebuild the array there and mirror the data back. Then, I'd have both the primary storage (on the FreeNAS box) and a backup (which I don't have currently) using the external drive enclosure on the Debian box. My big question is... most of these external drive boxes seem to claim support for JBOD, RAID 0, 1, 10, 5, etc. - should I presume that is simply fake RAID like many commodity mobos have, and not really usable in Linux? In that case, with all the drives hanging off the one eSATA connection, will Linux (specifically Debian Squeeze, as I plan on upgrading that box here shortly) see all four drives, or just the first one? Will I be able to configure them in a RAID5 array as desired? Thanks, Monte

  Read the article

• Windows 7 - Wireless Signal Good - Internet Often Says Limited or No Activity

  - by Anthony Trilussa Pizzo

  Hi - I have a New Dell Studio XPS latop that I hooked up in early January of 2010. The Dell Studio XPS laptop is connected to my wireless router (Belkin Wireless N). The router was purchased in Februaru of 2010 because I thought my router was bad (A D-Link router). Comcast is my ISP. Everyday, at random times, the internet will have a good signal (according to the little Win 7 icon on the taskbar) but I will receive a message saying limited or no internet access and I cannot access the internet. I have the internet setup to automatically get an IP and I did the IPCONFIG release / renew but with no success. I even had a WiFi enabled Blackberry right next to my computer and whenever the computer loses an WiFi connection, so does the Blackberry. The router isnt't bad, because the old router did the same thing - giving me limited or no internet access while working sometimes. I also tried using two other laptops in same physical position as my Dell Studio XPS laptop and they have the same problem. I am going crazy trying to figure this out as I have called the Router Company (Belkin), my ISP (Comcast), and my computer maker (Dell). Can anyone offer some suggestions and I can try them as we work through this and maybe one of the suggestion will be right one. Thanks in advance for even reading my problem. I searched for a problem similar to mine on the internet, but I have not been able to keep a steady internet connection. (Side note - I used to have an IBM thinkpad laptop and D - Link router and for years that wireless connection worked FLAWLESSLY, with the same physical set up - the laptop in my bedroom, and the router in the basement.)

  Read the article

• Bind9 zone files

  - by user42780

  Well for the better part of the last two hours I've tried to figure out what is actually wrong, but I can't seem to find anything obvious to me. What I'm trying to do is setup my DNS for say(per example) domain.com. This should include two NS records, namely ns1.domain.com and ns2.domain.com. With that there should be a mail record, as well as a CNAME record for www. I've been trough roughly 20 how to's in the last two hours, rewrote everything from scratch four times and I still can't seem to find whats wrong. My only suspicion to this might be two things; the error I get from the bind9 daemon when I stop the service, and the named.conf file. The error I get from the bind9 daemon when stopping the service is: * Stopping domain name service... bind9 rndc: connection to remote host closed This may indicate that * the remote server is using an older version of the command protocol, * this host is not authorized to connect, * the clocks are not syncronized, or * the key is invalid. I honestly doesn't know what this means, apart from the key defined in /etc/bind/rndc.key that's not in the named.conf file(yes, I did try to add it to no avail). Here's all the zone files, and configuration files; http://208.77.101.5/bind9/ If anyone could help, it would be greatly appreciated.

  Read the article

• Why is my cat5e cable not okay?

  - by torbengb

  My LAN cable seems to work (indicator LED lights up) but the computer can't find a connection. What's wrong? Setup: I had to run a network cable from a router in one room to a computer to another room, through a hole in the wall that was too small to pass the RJ-45 plug through. The plug was cut off and the cable passed through the wall. Then a new plug was crimped on using this detailed explanation. The connection didn't work because the (factory-made!) plug in the other end used a non-standard wire order. I crimped a new plug on again, using the exact same order of the factory-made plug. The LED indicator lights up on both ends, but the computer cannot find a connection. What can be wrong? How can I find out? I don't have a cable tester. By visually inspecting my new plug, I think it's good; the wire order matches the other end, and all wires are all the way inside the plug and reach the connector piece. I've used the cable before (with both factory-made ends) so i don't think that the cable itself has a defect.

  Read the article

• Apache directory structure with multiple hosted languages.

  - by anomareh

  I just got a new work machine up and running and I'm trying to decide on how to set everything up directory wise. I've done some digging around and really haven't been able to find anything conclusive. I know it's a question with a variety of answers but I'm hoping there's some sort of general guidelines or best practices to go by. With that said, here are a few things specific to my situation. I will be doing actual development and testing on the same machine as the server. It is a single user machine in the sense that I will be the only one working on the machine. There will be multiple hosted languages, specifically PHP and RoR while possibly expanding later. I'd like the setup to translate well to a production environment. With those 3 things in mind there are a couple of things I've had in the back of mind. Seeing as it's a single user machine I haven't been able to decide whether or not I should be working on things out of my home directory or if they should be located outside of it. I'm feeling that outside of a user directory would be better as it would translate better to a production environment, but I'm also not sure if that will come with any permission annoyances or concerns seeing as I'll be working on the same machine. Hosting multiple languages seems like it may be a bit quirky. With PHP I've found you're generally just dumping the project somewhere in the document root where as something like a Rails app you have the entire project and you only want the public directory in the document root. Thanks for any insight, opinion, or just personal preference from experience anyone can offer.

  Read the article

• Trouble serving vhosts when trying to set up wildcard subdomains with dnsmasq in local development e

  - by Jeremy Kendall

  I'm trying to get wildcard DNS enabled on my laptop using dnsmasq. I realize that this has been asked and answered more than once on this forum, but I can't get the solution to work for me. Steps taken so far: Installed dnsmasq Set address=/example.dev/127.0.0.1 in dnsmasq.conf Set listen-address=127.0.0.1 in dnsmasq.conf Ensured nameserver 127.0.0.1 is in /etc/resolv.conf Set prepend domain-name-servers 127.0.0.1; in /etc/dhcp3/dhclient.conf Created a vhost for example.dev Restarted apache and dnsmasq Note: example.dev is not set in /etc/hosts My vhost for example.dev <VirtualHost *:80> ServerName example.dev DocumentRoot /home/jkendall/public_html/example/public ServerAlias *.example.dev # This should be omitted in the production environment SetEnv APPLICATION_ENV development <Directory /home/jkendall/public_html/example/public> DirectoryIndex index.php AllowOverride All Order allow,deny Allow from all </Directory> </VirtualHost> The setup above will server example.dev locally without any problem. It will also serve test.example.dev, but test.example.dev returns the default apache "It works!" index.html from /var/www rather than my index.php in /home/jkendall/public_html/example/public. The solution in this Server Fault thread suggests that address=/.example.dev/127.0.0.1 would resolve my problem, but when I try to use that solution, restarting dnsmasq results in a failure with the error message dnsmasq: error at line 62 of /etc/dnsmasq.conf For grins, I moved my project over to /var/www/example and modified the vhost appropriately. I got the same result as described above. At this point I'm not sure what other steps I can take to resolve the issue. Thoughts?

  Read the article

• Installing SATA dvd burner on machine with no spare SATA ports/connectors

  - by Faheem Mitha

  Greetings. I have the following motherboard Tyan Thunder K8WE S2895A2NRF Motherboard - extended ATX - nForce Pro 2200/2050 - Socket 940 - UDMA133, Serial ATA-300 (RAID) - 2 x Gigabit Ethernet - FireWire - 6-1 channel audio This is part of a computer that was assembled in the winter of 2006/2007. The user manual says the following with regard to SATA Integrated SATAII Generation 1 Controllers (from NForce Professional 2200) Two integrated dual port SATA II controllers Four SATA connectors support up to four drives 3 Gb/s per direction per channel NvRAID v2.0 support Supports RAID 0, 1, 0+1 and JBOD. I just purchased a SATA DVD burner. Here is the page for the product http://www.amazon.ca/gp/product/B002QGDWLK/ The problem I am facing is that I already have 4 SATA drives installed. I don't want to remove any of them. However, I want the DVD burner above installed as well. The person I am consulting with here (Bombay, India) tells me that my four available SATA ports are filled, and that my only option is to install a SATA card into the one free PCI slot on the motherboard. However, he says that with this setup I will not be able to boot from the DVD drive. Are these statements correct, and what are my other options if any? Even it the statements in the last para are true, I suppose I could use one of the motherboard connectors/ports there are currently being used with the hard drives with the DVD drive, and use the "add-on" connector with one of the hard drives. Not all the 4 hard drives need to be bootable. BTW, despite having read through http://en.wikipedia.org/wiki/Serial_ATA#Cables.2C_connectors.2C_and_ports I am fuzzy on the differences between connectors, cables and ports. Thanks in advance.

  Read the article

• Solr error; JNDI not configured for solr; Anybody know what this means?

  - by Camran

  I am installing solr on my VPS (Ubuntu 9.10) via PuTTY. First, I thought about installing Solr with Tomcat, but then after installing tomcat, I changed my mind and went for the Jetty which comes with Solr. Now that I have setup everything on my Server, and try to start the "start.jar" file, I get some errors... Here is some text from the log file: 2010-05-29 00:22:42.074::INFO: jetty-6.1.3 2010-05-29 00:22:42.134::INFO: Extract jar:file:/var/www/webapps/solr.war!/ to /var/www/work/Jetty_0_0_0_0_8983_solr.war__solr__k1kf17/webapp May 29, 2010 12:22:42 AM org.apache.solr.core.SolrResourceLoader locateSolrHome INFO: JNDI not configured for solr (NoInitialContextEx) May 29, 2010 12:22:42 AM org.apache.solr.core.SolrResourceLoader locateSolrHome INFO: solr home defaulted to 'solr/' (could not find system property or JNDI) May 29, 2010 12:22:42 AM org.apache.solr.core.SolrResourceLoader <init> INFO: Solr home set to 'solr/' May 29, 2010 12:22:42 AM org.apache.solr.servlet.SolrDispatchFilter init INFO: SolrDispatchFilter.init() May 29, 2010 12:22:42 AM org.apache.solr.core.SolrResourceLoader locateSolrHome INFO: JNDI not configured for solr (NoInitialContextEx) May 29, 2010 12:22:42 AM org.apache.solr.core.SolrResourceLoader locateSolrHome INFO: solr home defaulted to 'solr/' (could not find system property or JNDI) May 29, 2010 12:22:42 AM org.apache.solr.core.CoreContainer$Initializer initialize INFO: looking for solr.xml: /var/www/solr/solr.xml May 29, 2010 12:22:42 AM org.apache.solr.core.SolrResourceLoader <init> INFO: Solr home set to 'solr/' Anybody know what this is? Thanks

  Read the article

• Ubuntu in VirtualBox File Modified Time in Future and PHP slow file operations

  - by user1750

  For some reason, some of my files have a last modified date in the future. In addition to this, file operations in PHP are SUPER slow. For example, rebuilding the Symfony2 cache can take over 40 seconds (its takes 1-2 on my MacBook Pro). Notice the time for ListingsCRUDController.php. It just says "2012". In order see the date more clearly I ran ls --time-style="full-iso" -l For some reason it shows that this file's last modified date is ~5 hours into the future. System time: To make things more confusing, the system will intermittently speed up. Suddenly, my app will start serving requests in 1-2 seconds (down from 40 seconds) for no apparent reason. I mean I don't do anything to my code/system config - it just changes. Also, during a slow PHP request, the php5-fpm process (nginx) uses 100% of the CPU for the duration of the request. This is the second VM this has happened on and I need to know why its doing this. It has become unusable. Information About My Setup VirtualBox 4.2.0 Host: Macbook Pro Guest: Ubuntu Server 12.04 Package dkms is installed Timezones match for Ubuntu and PHP. Things I've Tried Both Apache and Nginx. APC enabled and disabled. Xdebug enabled and disabled. 1 processor up to 4 processors. 1gb memory up to 4gb memory. I've installed Ubuntu using the regular kernel and the VM kernel.

  Read the article

• Failed to bring up eth1 in a dual ips solution in ubuntu

  - by lxyu

  I'm using ubuntu 12.04. I tried to assign two ips to two ethernet cards in my server. The content of /etc/network/interfaces is like this: auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 114.80.156.a netmask 255.255.255.224 gateway 114.80.156.b auto eth1 iface eth1 inet static address 114.80.156.c netmask 255.255.255.240 gateway 114.80.156.d a b c d have different values, which means the two ips are in different vlans. But I can only bring up eth0 with this command: $ /etc/init.d/networking restart RTNETLINK answers: File exists Failed to bring up eth1. ...done. I have checked the question here which shows the same problem like the one I encountered: Can only bring up one of two interfaces But it seems it's not really solved. And in my situation, I need the 2 ips to use 2 different gateways. So how to fix this problem? Edit1, changed the example config ip from 192.168.0.0/16 subnet to another 'real' subnet. Edit2, the purpose of doing this is fairly simple. Because the ip range I previous in don't have more room for new servers, and I have to move to another ip range. So I want to make the public servers bind to 2 ips for the transition period. I only have really limited knowledge about routing and subnet. @BillThor @rackandboneman, would you please give me some keywords or links on how to setup route for 2 ips? and @Mike Pennington, how do you know I speak chinese?

  Read the article

• DD-WRT router causing IP address conflicts across network

  - by r.tanner.f

  My DD-WRT router has lost its mind! I just set up two DD-WRT routers, one as a WAP (working fine) and one in Client Bridge (routed) mode (the problem). Not long after setup I started seeing IP address conflicts on other machines. The event log always points the finger at my Client Bridge router's MAC address. Neighbour table overflow The log on my router is flooded with Neighbour table overflow errors. These start a minute or two after boot. The network is rather large, with +200 IP addresses being used in this subnet. The other router shows no such errors. Mass ARP requests from 1.1.1.1 I'm also seeing constant ARP requests (with the problem router's MAC address) from 1.1.1.1. Seems like it's bugging everything on the network for its MAC address and then promptly forgetting it (or never receiving a response). Configuration: Model: Buffalo N600 Firmware: DD-WRT v24SP2-MULTI (03/21/11) Wireless Mode: Client Bridge (routed) I'm not sure what configuration details are relevant and I'd rather not have comments flooded, so just ping me in this chat if you want to know something. Why is my router stealing IP addresses and how can I stop it?

  Read the article

• Data Protection Manager System Protection Backups Failing

  - by TrueDuality

  I'm just starting to setup DPM 2010 in a test environment with a Domain Controller and a File Server. Everything seem to be working fairly well and I can get all of my backup jobs to succeed except for the "Computer\System Protection" backups. Both servers are running fully up to date 64 bit Windows Server 2008 R2 Enterprise with Service Pack 1. The error that is being provided is: DPM cannot create a backup because Windows Server Backup (WSB) on the protected computer encountered an error (WSB Event ID: 517, WSB Error Code: 0x8078001D). (ID 30229 Details: Internal error code: 0x809909FB) This Microsoft Knowledge Base article describes the issue perfectly and provides a hotfix. I downloaded the hotfix, moved it onto the affected server, attempt to run it and receive the following error: The update is not applicable to your computer. I've verified that I have indeed downloaded the 64 bit version. According to this thread the hotfix got rolled into Service Pack 1, yet I'm still experiencing the issue. Both machines do have the Windows Server Backup feature installed. Can anybody point me in the right direction? What am I missing?

  Read the article

• Correctly setting up UFW on Ubuntu Server 10 LTS which has Nginx, FastCGI and MySQL?

  - by littlejim84

  I'm wanting to get my firewall on my new webserver to be as secure as it needs to be. After I did research for iptables, I came across UFW (Uncomplicated FireWall). This looks like a better way for me to setup a firewall on Ubuntu Server 10 LTS and seeing that it's part of the install, it seems to make sense. My server will have Nginx, FastCGI and MySQL on it. I also want to be allow SSH access (obviously). So I'm curious to know exactly how I should set up UFW and is there anything else I need to take into consideration? After doing research, I found an article that explains it this way: # turn on ufw ufw enable # log all activity (you'll be glad you have this later) ufw logging on # allow port 80 for tcp (web stuff) ufw allow 80/tcp # allow our ssh port ufw allow 5555 # deny everything else ufw default deny # open the ssh config file and edit the port number from 22 to 5555, ctrl-x to exit nano /etc/ssh/sshd_config # restart ssh (don't forget to ssh with port 5555, not 22 from now on) /etc/init.d/ssh reload This all seems to make sense to me. But is it all correct? I want to back this up with any other opinions or advice to ensure I do this right on my server. Many thanks!

  Read the article

< Previous Page | 675 676 677 678 679 680 681 682 683 684 685 686  | Next Page >